ADC082S021CIMMX - National Semiconductor

ADC082S021

ADC082S021 2 Channel, 50 ksps to 200 ksps, 8-Bit A/D Converter

Literature Number: SNAS282C

ADC082S021

February 2, 2010

2 Channel, 50 ksps to 200 ksps, 8-Bit A/D Converter

General Description

The ADC082S021 is a low-power, two-channel CMOS 8-bit

analog-to-digital converter with a high-speed serial interface.

Unlike the conventional practice of specifying performance at

a single sample rate only, the ADC082S021 is fully specified

over a sample rate range of 50 ksps to 200 ksps. The con-

verter is based upon a successive-approximation register

architecture with an internal track-and-hold circuit. It can be

configured to accept one or two input signals at inputs IN1

and IN2.

The output serial data is straight binary, and is compatible with

several standards, such as SPI™, QSPI™, MICROWIRE,

and many common DSP serial interfaces.

The ADC082S021 operates with a single supply that can

range from +2.7V to +5.25V. Normal power consumption us-

ing a +3V or +5V supply is 1.6 mW and 5.8 mW, respectively.

The power-down feature reduces the power consumption to

just 0.12 µW using a +3V supply, or 0.35 µW using a +5V

supply.

The ADC082S021 is packaged in an 8-lead MSOP package.

Operation over the industrial temperature range of −40°C to

+85°C is guaranteed.

Features

■Specified over a range of sample rates.

■Two input channels

■Variable power management

■Single power supply with 2.7V - 5.25V range

Key Specifications

■DNL ±0.04 LSB (typ)

■INL ±0.04 LSB (typ)

■SNR 49.6 dB (typ)

■Power Consumption

■—3V Supply 1.6 mW (typ)

—5V Supply 5.8 mW (typ)

Applications

■Portable Systems

■Remote Data Acquisition

■Instrumentation and Control Systems

Pin-Compatible Alternatives by Resolution and Speed

All devices are fully pin and function compatible.

Resolution Specified for Sample Rate Range of:

50 to 200 ksps 200 to 500 ksps 500 ksps to 1 Msps

12-bit ADC122S021 ADC122S051 ADC122S101

10-bit ADC102S021 ADC102S051 ADC102S101

8-bit ADC082S021 ADC082S051 ADC082S101

Connection Diagram

20124805

Ordering Information

Order Code Temperature Range Description Top Mark

ADC082S021CIMM −40°C to +85°C 8-Lead MSOP Package X16C

ADC082S021CIMMX −40°C to +85°C 8-Lead MSOP Package, Tape & Reel X16C

ADC082S021EVAL Evaluation Board

TRI-STATE® is a trademark of National Semiconductor Corporation

QSPI™ and SPI™ are trademarks of Motorola, Inc.

ADC082S021 2 Channel, 50 ksps to 200 ksps, 8-Bit A/D Converter

Block Diagram

20124807

Pin Descriptions and Equivalent Circuits

Pin No. Symbol Description

ANALOG I/O

5,4 IN1 and IN2 Analog inputs. These signals can range from 0V to VA.

DIGITAL I/O

8 SCLK Digital clock input. This clock directly controls the conversion and readout processes.

7 DOUT Digital data output. The output samples are clocked out at this pin on falling edges of the

SCLK pin.

6 DIN Digital data input. The ADC082S021's Control Register is loaded through this pin on rising

edges of the SCLK.

1 CS Chip select. On the falling edge of CS, a conversion process begins. Conversions

continue as long as CS is held low.

POWER SUPPLY

2VA

Positive supply pin. This pin should be connected to a quiet +2.7V to +5.25V source and

bypassed to GND with a 1 µF capacitor and a 0.1 µF monolithic capacitor located within

1 cm of the power pin.

3 GND The ground return for the die.

www.national.com 2

ADC082S021

Absolute Maximum Ratings (Note 1, Note

If Military/Aerospace specified devices are required,

please contact the National Semiconductor Sales Office/

Distributors for availability and specifications.

Analog Supply Voltage VA−0.3V to 6.5V

Voltage on Any Pin to GND −0.3V to VA +0.3V

Input Current at Any Pin (Note 3) ±10 mA

Package Input Current (Note 3) ±20 mA

Power Consumption at TA = 25°C See (Note 4)

ESD Susceptibility (Note 5)

Human Body Model

Machine Model

2500V

250V

Junction Temperature +150°C

Storage Temperature −65°C to +150°C

Operating Ratings (Note 1, Note 2)

Operating Temperature Range −40°C ≤ TA ≤ +85°C

VA Supply Voltage +2.7V to +5.25V

Digital Input Pins Voltage Range −0.3V to VA

Clock Frequency 50 kHz to 16 MHz

Analog Input Voltage 0V to VA

Package Thermal Resistance

Package θJA

8-lead MSOP 250°C / W

Soldering process must comply with National

Semiconductor's Reflow Temperature Profile specifications.

Refer to www.national.com/packaging.(Note 6)

ADC082S021 Converter Electrical Characteristics (Note 9)

The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 0.8 MHz to 3.2 MHz,

fSAMPLE = 50 ksps to 200 ksps, CL = 50 pF, unless otherwise noted. Boldface limits apply for TA = TMIN to TMAX: all other limits

TA = 25°C.

Symbol Parameter Conditions Typical Limits

(Note 7)Units

STATIC CONVERTER CHARACTERISTICS

Resolution with No Missing Codes 8Bits

INL Integral Non-Linearity ±0.04 ±0.2 LSB (max)

DNL Differential Non-Linearity ±0.04 ±0.2 LSB (max)

VOFF Offset Error +0.52 ±0.7 LSB (max)

OEM Channel to Channel Offset Error Match ±0.01 ±0.3 LSB (max)

FSE Full-Scale Error +0.51 ±0.7 LSB (max)

FSEM Channel to Channel Full-Scale Error

Match +0.01 ±0.3 LSB (max)

DYNAMIC CONVERTER CHARACTERISTICS

SINAD Signal-to-Noise Plus Distortion Ratio VA = +2.7 to 5.25V

fIN = 39.9 kHz, −0.02 dBFS 49.6 49.1 dB (min)

SNR Signal-to-Noise Ratio VA = +2.7 to 5.25V

fIN = 39.9 kHz, −0.02 dBFS 49.6 49.2 dB (min)

THD Total Harmonic Distortion VA = +2.7 to 5.25V

fIN = 39.9 kHz, −0.02 dBFS −76 −62 dB (max)

SFDR Spurious-Free Dynamic Range VA = +2.7 to 5.25V

fIN = 39.9 kHz, −0.02 dBFS 68 63 dB (min)

ENOB Effective Number of Bits VA = +2.7 to 5.25V

fIN = 39.9 kHz, −0.02 dBFS 7.9 7.9 Bits (min)

Channel-to-Channel Crosstalk VA = +5.25V

fIN = 40.2 kHz −73 dB

IMD

Intermodulation Distortion, Second

Order Terms

VA = +5.25V

fa = 40.161 kHz, fb = 41.015 kHz −78 dB

Intermodulation Distortion, Third Order

Terms

VA = +5.25V

fa = 40.161 kHz, fb = 41.015 kHz −73 dB

FPBW -3 dB Full Power Bandwidth VA = +5V 11 MHz

VA = +3V 8 MHz

3 www.national.com

ADC082S021

Symbol Parameter Conditions Typical Limits

(Note 7)Units

ANALOG INPUT CHARACTERISTICS

VIN Input Range 0 to VAV

IDCL DC Leakage Current ±1 µA (max)

CINA Input Capacitance Track Mode 33 pF

Hold Mode 3 pF

DIGITAL INPUT CHARACTERISTICS

VIH Input High Voltage VA = +5.25V 2.4 V (min)

VA = +3.6V 2.1 V (min)

VIL Input Low Voltage 0.8 V (max)

IIN Input Current VIN = 0V or VIN = VA ±10 µA (max)

CIND Digital Input Capacitance 2 4pF (max)

DIGITAL OUTPUT CHARACTERISTICS

VOH Output High Voltage ISOURCE = 200 µA VA − 0.03 VA − 0.5 V (min)

ISOURCE = 1 mA VA − 0.1

VOL Output Low Voltage ISINK = 200 µA 0.03 0.4 V (max)

ISINK = 1 mA 0.1

IOZH, IOZL TRI-STATE® Leakage Current ±0.01 ±1 µA (max)

COUT TRI-STATE® Output Capacitance 2 4pF (max)

Output Coding Straight (Natural) Binary

POWER SUPPLY CHARACTERISTICS (CL = 10 pF)

VAAnalog Supply Voltage 2.7 V (min)

5.25 V (max)

Supply Current, Normal Mode

(Operational, CS low)

VA = +5.25V,

fSAMPLE = 200 ksps, fIN = 40 kHz 1.1 1.7 mA (max)

VA = +3.6V,

fSAMPLE = 200 ksps, fIN = 40 kHz 0.45 0.8 mA (max)

Supply Current, Shutdown (CS high)

VA = +5.25V,

fSAMPLE = 0 ksps 200 nA

VA = +3.6V,

fSAMPLE = 0 ksps 200 nA

Power Consumption, Normal Mode

(Operational, CS low)

VA = +5.25V 5.8 8.9 mW (max)

VA = +3.6V 1.6 2.9 mW (max)

Power Consumption, Shutdown (CS

high)

VA = +5.25V 1.05 µW

VA = +3.6V 0.72 µW

AC ELECTRICAL CHARACTERISTICS

fSCLK Maximum Clock Frequency (Note 8) 0.8 MHz (min)

3.2 MHz (max)

fSSample Rate (Note 8) 50 ksps (min)

200 ksps (max)

tCONV Conversion Time 13 SCLK cycles

DC SCLK Duty Cycle fSCLK = 3.2 MHz 50 30 % (min)

70 % (max)

tACQ Track/Hold Acquisition Time Full-Scale Step Input 3SCLK cycles

Throughput Time Acquisition Time + Conversion Time 16 SCLK cycles

www.national.com 4

ADC082S021

ADC082S021 Timing Specifications

The following specifications apply for VA = +2.7V to 5.25V, GND = 0V, fSCLK = 0.8 MHz to 3.2 MHz,

fSAMPLE = 50 ksps to 200 ksps, CL = 50 pF, Boldface limits apply for TA = TMIN to TMAX: all other limits TA = 25°C.

Symbol Parameter Conditions Typical Limits

(Note 7)Units

tCSU Setup Time SCLK High to CS Falling Edge (Note 10)VA = +3.0V −3.5 10 ns (min)

VA = +5.0V −0.5

tCLH Hold time SCLK Low to CS Falling Edge (Note 10)VA = +3.0V +4.5 10 ns (min)

VA = +5.0V +1.5

tEN Delay from CS Until DOUT active VA = +3.0V +4 30 ns (max)

VA = +5.0V +2

tACC Data Access Time after SCLK Falling Edge VA = +3.0V +16.5 30 ns (max)

VA = +5.0V +15

tSU Data Setup Time Prior to SCLK Rising Edge +3 10 ns (min)

tHData Valid SCLK Hold Time +3 10 ns (min)

tCH SCLK High Pulse Width 0.5 x tSCLK 0.3 x tSCLK ns (min)

tCL SCLK Low Pulse Width 0.5 x tSCLK 0.3 x tSCLK ns (min)

tDIS CS Rising Edge to DOUT High-Impedance

Output Falling VA = +3.0V 1.7

20 ns (max)

VA = +5.0V 1.2

Output Rising VA = +3.0V 1.0

VA = +5.0V 1.0

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is

functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed

specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test

conditions.

Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified.

Note 3: When the input voltage at any pin exceeds the power supply (that is, VIN < GND or VIN > VA), the current at that pin should be limited to 10 mA. The 20

mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two. The Absolute

Maximum Rating specification does not apply to the VA pin. The current into the VA pin is limited by the Analog Supply Voltage specification.

Note 4: The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by TJmax, the

junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula PDMAX = (TJmax − TA)/θJA. The values

for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven

beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.

Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through zero ohms

Note 6: Reflow temperature profiles are different for lead-free and non-lead-free packages.

Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level).

Note 8: This is the frequency range over which the electrical performance is guaranteed. The device is functional over a wider range which is specified under

Operating Ratings.

Note 9: Min/max specification limits are guaranteed by design, test, or statistical analysis.

Note 10: Clock may be either high or low when CS is asserted as long as setup and hold times tCSU and tCLH are strictly observed.

5 www.national.com

ADC082S021

Timing Diagrams

20124851

ADC082S021 Operational Timing Diagram

20124808

Timing Test Circuit

20124806

ADC082S021 Serial Timing Diagram

20124850

SCLK and CS Timing Parameters

www.national.com 6

ADC082S021

Specification Definitions

ACQUISITION TIME is the time required to acquire the input

voltage. That is, it is time required for the hold capacitor to

charge up to the input voltage.

APERTURE DELAY is the time between the fourth falling

SCLK edge of a conversion and the time when the input signal

is acquired or held for conversion.

CONVERSION TIME is the time required, after the input volt-

age is acquired, for the ADC to convert the input voltage to a

digital word.

CROSSTALK is the coupling of energy from one channel into

the other channel, or the amount of signal energy from one

analog input that appears at the measured analog input.

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of

the maximum deviation from the ideal step size of 1 LSB.

DUTY CYCLE is the ratio of the time that a repetitive digital

waveform is high to the total time of one period. The specifi-

cation here refers to the SCLK.

EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE

BITS) is another method of specifying Signal-to-Noise and

Distortion or SINAD. ENOB is defined as (SINAD − 1.76) /

6.02 and says that the converter is equivalent to a perfect

ADC of this (ENOB) number of bits.

FULL POWER BANDWIDTH is a measure of the frequency

at which the reconstructed output fundamental drops 3 dB

below its low frequency value for a full scale input.

FULL SCALE ERROR (FSE) is a measure of how far the last

code transition is from the ideal 1½ LSB below VREF+ and is

defined as:

VFSE = Vmax + 1.5 LSB – VREF+

where Vmax is the voltage at which the transition to the maxi-

mum code occurs. FSE can be expressed in Volts, LSB or

percent of full scale range.

GAIN ERROR is the deviation of the last code transition

(111...110) to (111...111) from the ideal (VREF − 1.5 LSB), af-

ter adjusting for offset error.

INTEGRAL NON-LINEARITY (INL) is a measure of the de-

viation of each individual code from a line drawn from negative

full scale (½ LSB below the first code transition) through pos-

itive full scale (½ LSB above the last code transition). The

deviation of any given code from this straight line is measured

from the center of that code value.

INTERMODULATION DISTORTION (IMD) is the creation of

additional spectral components that are present at the output

and are not present at the input and result from two sinusoidal

frequencies being applied to the ADC input at the same time.

It is defined as the ratio of the power in the intermodulation

products to the total power in one of the original frequencies.

IMD is usually expressed in dB.

MISSING CODES are those output codes that will never ap-

pear at the ADC outputs. These codes cannot be reached with

any input value. The ADC082S021 is guaranteed not to have

any missing codes.

OFFSET ERROR is the deviation of the first code transition

(000...000) to (000...001) from the ideal (i.e. GND + 0.5 LSB).

SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in

dB, of the rms value of the input signal at the converter output

to the rms value of the sum of all other spectral components

below one-half the sampling frequency, not including d.c. or

harmonics included in the THD specification.

SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or

SINAD or SNDR) is the ratio, expressed in dB, of the rms

value of the input signal at the output to the rms value of all

of the other spectral components below half the clock fre-

quency, including all harmonics but excluding DC.

SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-

ence, expressed in dB, between the rms values of the input

signal at the output and the peak spurious signal, where a

spurious signal is any signal present in the output spectrum

that is not present at the input, excluding d.c.

TOTAL HARMONIC DISTORTION (THD) is the ratio, ex-

pressed in dBc, of the rms total of the first five harmonic

components at the output to the rms level of the input signal

frequency as seen at the output. THD is calculated as

where Af1 is the RMS power of the input frequency at the out-

put and Af2 through Af6 are the RMS power in the first 5

harmonic frequencies. Accurate THD measurement requires

a spectrally pure sine wave (monotone) at the ADC input.

THROUGHPUT TIME is the minimum time required between

the start of two successive conversion. It is the acquisition

time plus the conversion and read out times. In the case of

the ADC082S021, this is 16 SCLK periods.

7 www.national.com

ADC082S021

Typical Performance Characteristics TA = +25°C, fSAMPLE = 50 ksps to 200 ksps, fSCLK = 0.8 MHz to 3.2

MHz, fIN = 39.9 kHz unless otherwise stated.

DNL - VA = 3.0V

20124820

INL - VA = 3.0V

20124821

DNL - VA = 5.0V

20124862

INL - VA = 5.0V

20124863

DNL vs. Supply

20124822

INL vs. Supply

20124823

www.national.com 8

ADC082S021

DNL vs. Clock Frequency

20124824

INL vs. Clock Frequency

20124825

DNL vs. Clock Duty Cycle

20124826

INL vs. Clock Duty Cycle

20124827

DNL vs. Temperature

20124828

INL vs. Temperature

20124829

9 www.national.com

ADC082S021

SNR vs. Supply

20124830

THD vs. Supply

20124835

SNR vs. Clock Frequency

20124831

THD vs. Clock Frequency

20124836

SNR vs. Clock Duty Cycle

20124832

THD vs. Clock Duty Cycle

20124837

www.national.com 10

ADC082S021

SNR vs. Input Frequency

20124833

THD vs. Input Frequency

20124838

SNR vs. Temperature

20124834

THD vs. Temperature

20124839

SFDR vs. Supply

20124840

SINAD vs. Supply

20124845

11 www.national.com

ADC082S021

SFDR vs. Clock Frequency

20124841

SINAD vs. Clock Frequency

20124846

SFDR vs. Clock Duty Cycle

20124842

SINAD vs. Clock Duty Cycle

20124847

SFDR vs. Input Frequency

20124843

SINAD vs. Input Frequency

20124848

www.national.com 12

ADC082S021

SFDR vs. Temperature

20124844

SINAD vs. Temperature

20124849

ENOB vs. Supply

20124852

ENOB vs. Clock Frequency

20124853

ENOB vs. Clock Duty Cycle

20124854

ENOB vs. Input Frequency

20124855

13 www.national.com

ADC082S021

ENOB vs. Temperature

20124856

Spectral Response - 3V, 200 ksps

20124859

Spectral Response - 5V, 200 ksps

20124860

Power Consumption vs. Throughput

20124861

www.national.com 14

ADC082S021

Applications Information

1.0 ADC082S021 OPERATION

The ADC082S021 is a successive-approximation analog-to-

digital converter designed around a charge-redistribution dig-

ital-to-analog converter. Simplified schematics of the

ADC082S021 in both track and hold modes are shown in

Figure 1 and Figure 2, respectively. In Figure 1, the

ADC082S021 is in track mode: switch SW1 connects the

sampling capacitor to one of two analog input channels

through the multiplexer, and SW2 balances the comparator

inputs. The ADC082S021 is in this state for the first three

SCLK cycles after CS is brought low.

Figure 2 shows the ADC082S021 in hold mode: switch SW1

connects the sampling capacitor to ground, maintaining the

sampled voltage, and switch SW2 unbalances the compara-

tor. The control logic then instructs the charge-redistribution

DAC to add fixed amounts of charge to the sampling capacitor

until the comparator is balanced. When the comparator is

balanced, the digital word supplied to the DAC is the digital

representation of the analog input voltage. The ADC082S021

is in this state for the fourth through sixteenth SCLK cycles

after CS is brought low.

The time when CS is low is considered a serial frame. Each

of these frames should contain an integer multiple of 16 SCLK

cycles, during which time a conversion is performed and the

result is clocked out at the DOUT pin while the multiplexer

address for the next conversion is clocked in at the DIN pin.

20124809

FIGURE 1. ADC082S021 in Track Mode

20124810

FIGURE 2. ADC082S021 in Hold Mode

2.0 USING THE ADC082S021

An ADC082S021 timing diagram and a serial interface timing

diagram for the ADC082S021 are shown in the Timing Dia-

grams section. CS is chip select, which initiates conversions

and frames the serial data transfers. SCLK (serial clock) con-

trols both the conversion process and the timing of serial data.

DOUT is the serial data output pin, where the conversion re-

sult is sent out as a serial data stream, MSB first. Data to be

written to the ADC082S021's Control Register is placed at

DIN, the serial data input pin. New data is written in at DIN

with each conversion.

A serial frame is initiated on the falling edge of CS and ends

on the rising edge of CS. Each frame must contain an integer

multiple of 16 rising SCLK edges. The ADC output data

(DOUT) is in a high impedance state when CS is high and is

active when CS is low. Thus, CS acts as an output enable.

Additionally, the device goes into a power down state when

CS is high and also between continuous conversion cycles.

During the first 3 cycles of SCLK, the ADC is in the track mode

acquiring the input voltage. For the next 13 SCLK cycles, the

conversion is accomplished and the data is clocked out, MSB

first, starting with the 5th clock. If there is more than one con-

version in a frame, the ADC will re-enter the track mode on

the falling edge of SCLK after the N*16th rising edge of SCLK,

and re-enter the hold/convert mode on the N*16+4th falling

edge of SCLK, where "N" is an integer.

When CS is brought high, SCLK is internally gated off. If SCLK

is stopped in the low state while CS is high, the subsequent

fall of CS will generate a falling edge of the internal version of

SCLK, putting the ADC into the track mode. This is seen by

the ADC as the first falling edge of SCLK. If SCLK is stopped

with SCLK high, the ADC enters the track mode on the first

falling edge of SCLK after the falling edge of CS.

During each conversion, data is clocked into the ADC at DIN

on the first 8 rising edges of SCLK after the fall of CS. For

each conversion, it is necessary to clock in the data indicating

15 www.national.com

ADC082S021

the input that is selected for the conversion after the current

one. See Tables 1, 2 and Table 3.

If CS and SCLK go low within the times defined by tCSU and

tCLH, the rising edge of SCLK that begins clocking data in at

DIN may or may not be one clock cycle later than expected.

It is, therefore, best to strictly observe the minimum tCSU and

tCLH times given in the Timing Specifications.

There are no power-up delays or dummy conversions re-

quired with the ADC082S021. The ADC is able to sample and

convert an input to full conversion immediately following pow-

er up. The first conversion result after power-up will be that of

IN1.

TABLE 1. Control Register Bits

Bit 7 (MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

DONTC DONTC ADD2 ADD1 ADD0 DONTC DONTC DONTC

TABLE 2. Control Register Bit Descriptions

Bit #: Symbol: Description

7 - 6, 2 - 0 DONTC Don't care. The value of these bits do not affect the device.

3 ADD0 These bits determine which input channel will be sampled and converted in the

next track/hold cycle. The mapping between codes and channels is shown in

Table 3.

4 ADD1

5 ADD2

TABLE 3. Input Channel Selection

ADD2 ADD1 ADD0 Input Channel

x 0 0 IN1 (Default)

x 0 1 IN2

x 1 x Not allowed. The output signal at the DOUT pin

is indeterminate if ADD1 is high.

www.national.com 16

ADC082S021

3.0 ADC082S021 TRANSFER FUNCTION

The output format of the ADC082S021 is straight binary. Code transitions occur midway between successive integer LSB values.

The LSB width for the ADC082S021 is VA/256. The ideal transfer characteristic is shown in Figure 3. The transition from an output

code of 0000 0000 to a code of 0000 0001 is at 1/2 LSB, or a voltage of VA/512. Other code transitions occur at steps of one LSB.

20124811

FIGURE 3. Ideal Transfer Characteristic

4.0 TYPICAL APPLICATION CIRCUIT

A typical application of the ADC082S021 is shown in

Figure 4. Power is provided, in this example, by the National

Semiconductor LP2950 low-dropout voltage regulator, avail-

able in a variety of fixed and adjustable output voltages. The

power supply pin is bypassed with a capacitor network locat-

ed close to the ADC082S021. Because the reference for the

ADC082S021 is the supply voltage, any noise on the supply

will degrade device noise performance. To keep noise off the

supply, use a dedicated linear regulator for this device, or

provide sufficient decoupling from other circuitry to prevent

noise from reaching the ADC082S021 supply pin. Because of

the ADC082S021's low power requirements, it is also possi-

ble to use a precision reference as a power supply to maxi-

mize performance. The four-wire interface is shown connect-

ed to a microprocessor or DSP.

20124813

FIGURE 4. Typical Application Circuit

17 www.national.com

ADC082S021

5.0 ANALOG INPUTS

An equivalent circuit for one of the ADC082S021's input chan-

nels is shown in Figure 5. Diodes D1 and D2 provide ESD

protection for the analog inputs. At no time should any input

go beyond (VA + 300 mV) or (GND − 300 mV), as these ESD

diodes will begin conducting, which could result in erratic op-

eration. For this reason, these ESD diodes should NOT be

used to clamp the input signal.

The capacitor C1 in Figure 5 has a typical value of 3 pF, and

is mainly the package pin capacitance. Resistor R1 is the on

resistance of the multiplexer and track / hold switch, and is

typically 500 ohms. Capacitor C2 is the ADC082S021 sam-

pling capacitor and is typically 30 pF. The ADC082S021 will

deliver best performance when driven by a low-impedance

source to eliminate distortion caused by the charging of the

sampling capacitance. This is especially important when us-

ing the ADC082S021 to sample AC signals. Also important

when sampling dynamic signals is a band-pass or low-pass

filter to reduce harmonics and noise, improving dynamic per-

formance.

20124814

FIGURE 5. Equivalent Input Circuit

6.0 DIGITAL INPUTS AND OUTPUTS

The ADC082S021's digital output DOUT is limited by, and

cannot exceed, the supply voltage, VA. The digital input pins

are not prone to latch-up and, and although not recommend-

ed, SCLK, CS and DIN may be asserted before VA without

latchup risk.

7.0 POWER SUPPLY CONSIDERATIONS

The ADC082S021 is fully powered-up whenever CS is low,

and fully powered-down whenever CS is high, with one ex-

ception: the ADC082S021 automatically enters power-down

mode between the 16th falling edge of a conversion and the

1st falling edge of the subsequent conversion (see Timing

Diagrams).

The ADC082S021 can perform multiple conversions back to

back; each conversion requires 16 SCLK cycles. The

ADC082S021 will perform conversions continuously as long

as CS is held low.

7.1 Power Management

When the ADC082S021 is operated continuously in normal

mode, the maximum throughput is fSCLK/16. Throughput may

be traded for power consumption by running fSCLK at its max-

imum 3.2 MHz and performing fewer conversions per unit

time, putting the ADC082S021 into shutdown mode between

conversions. A plot of typical power consumption versus

throughput is shown in the Typical Performance Curves sec-

tion. To calculate the power consumption for a given through-

put, multiply the fraction of time spent in the normal mode by

the normal mode power consumption and add the fraction of

time spent in shutdown mode multiplied by the shutdown

mode power consumption. Generally, the user will put the part

into normal mode and then put the part back into shutdown

mode. Note that the curve of power consumption vs. through-

put is nearly linear. This is because the power consumption

in the shutdown mode is so small that it can be ignored for all

practical purposes.

7.2 Power Supply Noise Considerations

The charging of any output load capacitance requires current

from the power supply, VA. The current pulses required from

the supply to charge the output capacitance will cause voltage

variations on the supply. If these variations are large enough,

they could degrade SNR and SINAD performance of the ADC.

Furthermore, discharging the output capacitance when the

digital output goes from a logic high to a logic low will dump

current into the die substrate, which is resistive. Load dis-

charge currents will cause "ground bounce" noise in the sub-

strate that will degrade noise performance if that current is

large enough. The larger is the output capacitance, the more

current flows through the die substrate and the greater is the

noise coupled into the analog channel, degrading noise per-

formance.

To keep noise out of the power supply, keep the output load

capacitance as small as practical. If the load capacitance is

greater than 50 pF, use a 100 Ω series resistor at the ADC

output, located as close to the ADC output pin as practical.

This will limit the charge and discharge current of the output

capacitance and improve noise performance.

www.national.com 18

ADC082S021

Physical Dimensions inches (millimeters) unless otherwise noted

8-Lead MSOP

Order Number ADC082S021CIMM, ADC082S021CIMMX

NS Package Number P0MUA08A

19 www.national.com

ADC082S021

Notes

ADC082S021 2 Channel, 50 ksps to 200 ksps, 8-Bit A/D Converter

For more National Semiconductor product information and proven design tools, visit the following Web sites at:

www.national.com

Products Design Support

Amplifiers www.national.com/amplifiers WEBENCH® Tools www.national.com/webench

Audio www.national.com/audio App Notes www.national.com/appnotes

Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns

Data Converters www.national.com/adc Samples www.national.com/samples

Interface www.national.com/interface Eval Boards www.national.com/evalboards

LVDS www.national.com/lvds Packaging www.national.com/packaging

Power Management www.national.com/power Green Compliance www.national.com/quality/green

Switching Regulators www.national.com/switchers Distributors www.national.com/contacts

LDOs www.national.com/ldo Quality and Reliability www.national.com/quality

LED Lighting www.national.com/led Feedback/Support www.national.com/feedback

Voltage References www.national.com/vref Design Made Easy www.national.com/easy

PowerWise® Solutions www.national.com/powerwise Applications & Markets www.national.com/solutions

Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero

Temperature Sensors www.national.com/tempsensors SolarMagic™ www.national.com/solarmagic

PLL/VCO www.national.com/wireless PowerWise® Design

University

www.national.com/training

THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION

(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY

OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO

SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,

IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS

DOCUMENT.

TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT

NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL

PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR

APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND

APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE

NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.

EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO

LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE

AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR

PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY

RIGHT.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR

SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL

COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and

whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected

to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform

can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.

National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other

brand or product names may be trademarks or registered trademarks of their respective holders.

For the most current product information visit us at www.national.com

National Semiconductor

Americas Technical

Support Center

Email: support@nsc.com

Tel: 1-800-272-9959

National Semiconductor Europe

Technical Support Center

Email: europe.support@nsc.com

National Semiconductor Asia

Pacific Technical Support Center

Email: ap.support@nsc.com

National Semiconductor Japan

Technical Support Center

Email: jpn.feedback@nsc.com

www.national.com

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,

and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should

obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are

sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard

warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where

mandated by government requirements, testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and

applications using TI components. To minimize the risks associated with customer products and applications, customers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,

or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information

published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a

warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual

property of the third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied

by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive

business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional

restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all

express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not

responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably

be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing

such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and

acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products

and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be

provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in

such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are

specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military

specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at

the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.

TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are

designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated

products in automotive applications, TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Audio www.ti.com/audio Communications and Telecom www.ti.com/communications

Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers

Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps

DLP®Products www.dlp.com Energy and Lighting www.ti.com/energy

DSP dsp.ti.com Industrial www.ti.com/industrial

Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical

Interface interface.ti.com Security www.ti.com/security

Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Mobile Processors www.ti.com/omap

Wireless Connectivity www.ti.com/wirelessconnectivity

TI E2E Community Home Page e2e.ti.com

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265