AASL4805QR425S/5-C1 - Kingbright

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 1 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

HIGH BRIGHTNESS LED LIGHT BAR

AASL4805QR425S/5 SERIES

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.25(0.01") unless otherwise noted.

3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

DISCHARGE

SENSITIVE

DEVICES

Features

zDimension: 48mm X 5mm X 1.6mm.

zInstant light.

zLinear type.

zHigh efficiency.

zLong operating life.

zLow power consumption.

zMore energy efficient than incandescent,most halogen lamps, and fluorescent lamp.

zRoHS compliant.

Chip

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 2 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

Precautions

1. Do not touch the lens with any sharp object.

2. No stress should be applied on the lens.

3. Thermal grease between the light bar and heat sink is recommended to fill air gaps for better thermal conductivity.

4. For securing the LED light bar, M2 screws are recommended. The light bar should not be bent or stressed in any way

which could damage the internal circuit.

5. To prevent damages caused by electrostatic discharge (ESD), it is recommended to wear proper gear such as

wristband or anti-static gloves when handling the product.

6. Constant current source is recommended to power the light bar. When more than one light bar are used, they should

be connected in series if possible.

7. Thermal management should be taken into consideration when using the product. Maximum driving current

should be reduced accordingly at higher ambient temperature to prevent overheating.

8. Soldering recommendations:

zSoldering iron power should not exceed 40W, and should not be in contact with the joint for more than 3.5 secs.

zThe maximum soldering temperature should be less than 350°C.

zDo not touch the product immediately after soldering.

zNot reflow compatible.

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 3 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

Absolute Maximum Ratings

Electrical / Optical Characteristics

Note:

1. 1/10 Duty Cycle, 0.1ms Pulse Width.

Test Item

Moisture-proof Test 85°C , 85%RH for 1000 hours

Test Condition

Selection Guide

Erp. Part No. Dice Lens Type CCT Range [2] Luminous Flux (lm)

@ 500mA [1]

Min. Typ. Max. Min. Typ.

1209000166 AASL4805QR425S/5-C1 Cool White WATER CLEAR 5310K 6000K 7040K 280 330

1209000167 AASL4805QR425S/5-N2 Neutral White WATER CLEAR 4260K 4700K 5310K 280 320

1209000168 AASL4805QR425S/5-W2 Warm White WATER CLEAR 2870K 3000K 3220K 240 290

Notes:

1. Flux is measured with an accuracy of +/-15%.

2. CCT selection acc.to CCT groups and an accuracy of +/-300K.

Note:

1. Forward Voltage is measured with an accuracy of +/-0.1V.

Parameter Symbol

Min. Typ. Max. Units Conditions

Forward Voltage [1] VF 8.4 10.3 11.6 V

IF=700mA

Temperature Coefficient of

Forward Voltage ΔVF/ΔT - -2.9 -

mV/°C IF=700mA

Thermal Resistance Rth j-c - 3.5 °C/W IF=700mA

Emission Angle

2θ1/2

x direction - 120 - ° IF=700mA

2θ1/2

y direction - 120 - ° IF=700mA

Parameter Symbol Rating Units

Forward Current IF 500 mA

Forward Pulse Current [1] IFP 700 mA

Power Dissipation Pd 5.8 W

LED Junction Temperature Tj 120 °C

Operating Temperature Topr -30~+100 °C

Storage Temperature Tstg -40~+120 °C

Case Temperature Tc 100 °C

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 4 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 5 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 6 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 7 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

0.30

0.32

0.34

0.36

0.38

0.40

0.42

0.44

0.28 0.30 0.32 0.34 0.36 0.38 0.40 0.42 0.44 0.46 0.48 0.50

x

y

2500 K3000 K

4000 K

5000 K

6000 K

7000 K

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

W1

W2

W3

N1

N2

C1

Color Group Chromaticity Regions CCT (K)

Min. Typ. Max.

Warm White W1 1, 2, 3, 4 2580 2700 2870

W2 5, 6, 7, 8 2870 3000 3220

W3 9, 10, 11, 12 3220 3500 3710

N1 13, 14, 15, 16 3710 4000 4260

N2 17, 18, 19, 20, 21, 22 4260 4700 5310

Cool White C1 23, 24, 25, 26, 27, 28 5310 6000 7040

Neutral White

x y x y x y x y

1

0.4582 0.4099

8

0.4147 0.3814

15

0.3702 0.3722 0.3481 0.3557

0.4687 0.4289 0.4221 0.3984 0.3736 0.3874 0.3370 0.3472

0.4813 0.4319 0.4342 0.4028 0.3869 0.3958 0.3364 0.3328

0.4700 0.4126 0.4259 0.3853 0.3825 0.3798 0.3466 0.3411

2

0.4483 0.3919

9

0.4080 0.3916

16

0.3670 0.3578

23

0.3376 0.3616

0.4582 0.4099 0.4146 0.4089 0.3702 0.3722 0.3260 0.3512

0.4700 0.4126 0.4299 0.4165 0.3825 0.3798 0.3265 0.3371

0.4593 0.3944 0.4221 0.3984 0.3783 0.3646 0.3370 0.3472

3

0.4465 0.4071

10

0.4017 0.3751

17

0.3736 0.3874

24

0.3370 0.3472

0.4562 0.4260 0.4080 0.3916 0.3616 0.3788 0.3265 0.3371

0.4687 0.4289 0.4221 0.3984 0.3592 0.3641 0.3270 0.3230

0.4582 0.4099 0.4147 0.3814 0.3703 0.3726 0.3364 0.3328

4

0.4373 0.3893

11

0.3941 0.3848

18

0.3703 0.3726

25

0.3260 0.3512

0.4465 0.4071 0.3996 0.4015 0.3592 0.3641 0.3144 0.3408

0.4582 0.4099 0.4146 0.4089 0.3568 0.3495 0.3160 0.3274

0.4483 0.3919 0.4080 0.3916 0.3670 0.3578 0.3265 0.3371

5

0.4342 0.4028

12

0.3889 0.3690

19

0.3616 0.3788

26

0.3265 0.3371

0.4430 0.4212 0.3941 0.3848 0.3496 0.3702 0.3160 0.3274

0.4562 0.4260 0.4080 0.3916 0.3481 0.3557 0.3175 0.3139

0.4465 0.4071 0.4017 0.3751 0.3592 0.3641 0.3270 0.3230

6

0.4259 0.3853

13

0.3825 0.3798

20

0.3592 0.3641

27

0.3144 0.3408

0.4342 0.4028 0.3869 0.3958 0.3481 0.3557 0.3028 0.3304

0.4465 0.4071 0.4006 0.4044 0.3466 0.3411 0.3055 0.3177

0.4373 0.3893 0.3950 0.3875 0.3568 0.3495 0.3160 0.3274

7

0.4221 0.3984

14

0.3783 0.3646

21

0.3496 0.3702

28

0.3160 0.3274

0.4299 0.4165 0.3825 0.3798 0.3376 0.3616 0.3055 0.3177

0.4430 0.4212 0.3950 0.3875 0.3370 0.3472 0.3081 0.3049

0.4342 0.4028 0.3898 0.3716 0.3481 0.3557 0.3175 0.3139

22

CCT 2500-7000 K Bin Code

Notes:

Shipment may contain more than one chromaticity

regions.Orders for single chromaticity region are

generally not accepted.

Measurement tolerance of the chromaticity

coordinates is ±0.01.

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 8 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

AASL4805 Application Note

Introduction

The AASL4805 LED light bar provide very high light output, and can be configured to suit a wide rage of applications. However the

heat generated during operation, if not handled properly, could shorten the product life significantly. Therefore for optimal per-

formance, proper thermal management should be incorporated to keep it below the rated temperature. This document describes

the heat sink attachment procedure.

Attachment to Heat sink

1. Apply a thin layer (0.1 ~ 0.2 mm) of thermal grease on the bottom of the AASL4805 LED light bar.

2. Press the AASL4805 LED light bar firmly on the heat sink to ensure good contact between the heat sink and the LED light

bar. A guide for heat sink size selection at various driving currents is listed in the table below.

Current (mA) 350 500 600 700

Heat sink

surface area (mm2) 10,000 15,000 17,000 21,000

Rear surface Thermal glue on rear surface

3. A specifically designed electronic circuit is required to power the LED light bar. Do not connect the product directly to the main

power.

It is strongly recommended

that temperature of pad be

not highter than 75°C when

you use the product.

SPEC NO: DSAK3010 REV NO: V.1 DATE: JAN/15/2010 PAGE: 9 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: S.P.Chen

PACKING & LABEL SPECIFICATIONS AASL4805QR425S/5