INTRODUCTION
This Applicati on Manu al is produc ed for en gin eers who int end to des ign light ing it ems using the Stanle y Slim
Stick S-Type LED Modules.
Through the use of this Application Manual, the lighting items can use their unique characteristics effectively.
Safety precautions and notes on the necessary quality conditions for design are described in this manual.
Before the LED lighting item is designed, be sure to read this manual thoroughly and understand the
functions of LED modules.
For performance and quality specifications of LED modules, refer to specifications (separately supplied).
SPECIAL FEATURES OF SLIM STICK S-TYPE LED MODULE
The Stanley Slim Stick S-Type is a unique brand-new LED illumination module which has the special
characteristics described below.
・ The thin and na rrow stic k shape of the LED modul e is appli cable to illumin ation in stalle d in the narrow spa ces.
・ Emission color can be selected from either warm white or normal white.
・ Two LED configurations (15 or 30 LEDs) are available.
・ The LEDs are aligned in the same pitch.
・ By using a special connector supplied by BJB, LED modules can be joined and the joined LED module
emits the same pitch.
・ The LED module can operate on 12V DC power supply.
・ The LED luminous intensity and emission color dispersion are minimized by the regulation specified by
Stanley.
・ The Stanley LED Modules all conform to the RoHS Directive.
APPLICABLE LED MODULES
This Application Manual applies to the following Stanley Slim Stick S-Type.
MODEL EMITTED COLO R
(COL OR TEM P ERATUR E) NUMBER OF LEDS REMARKS
STW0101N Warm white (3,300K) 30 LEDs (10 mm pitch)
STW0201N Warm white (3,300K) 15 LEDs (20 mm pitch)
STN0101N White (5,000K) 30 LEDs (10 mm pitch)
STN0201N White (5,000K) 15 LEDs (20 mm pitch)
・ Direct L E D emission can serio usl y damage the eyes. Never vie w a LED emi ssi on directly.
・ Never use a disassembled LED mod ul e.
・ A LED generates heat while it is emitting.
(The ambient temperature is increased by 20℃
℃℃
℃ by a 30 LED unit).
Pay at t ent ion to avoiding burns and to prevent def or mation of t he LED mount uni t.
SLIM STICK S-TYPE LED MODULE
APPLICATIONS MANUAL
W
ARNING
1
TABLE OF CONTENTS
1. CHARACTERISTICS AND VARIATIONS･････････････････････････････････････････････････････ 1
2. GENERAL VI EW S, NAMES, DESCRIPTIONS ･･･････････････････････････････････････････････ 2
3. INS TALLAT ION , CONNECTION ･････････････････････････････････････････････････････････････ 3
4. POWER SUPPLY REQUIREMENT･･･････････････････････････････････････････････････････････ 5
5. CAUTIONS･･････････････････････････････････････････････････････････････････････････････････ 5
6. APPLIC ATION EXAMPLES OF SLIM STICK S-TYPE LED MO DULES ･･･････････････････････ 6
1. CHARACTERISTICS AND VARIATIONS
Select the desired LED module from the table below according to the illumination plan which describes the
emission color and the number of LED modules.
Model Emitted Color
(Color
Temperature)
Number of
LEDs
Forward
Voltage
TYP
(V cc)
Forward
Current
(mA)
Central
Illumination
H=0.5m
(lx)
Luminous
Flux
TYP
(lm)
Power
Consumption
(W)
STW0101N Warm white
(3,300K) 30 LEDs
(10 m m pitch)
12 200 80 45 2.4
STW0201N Warm white
(3,300K) 15 LEDs
(20 m m pitch)
12 100 40 24 1.2
STN0101N White
(5,000K) 30 LEDs
(10 m m pitch)
12 200 95 55 2.4
STN0201N White
(5,000K) 15 LEDs
(20 m m pitch)
12 100 60 29 1.2
●
●●
●BJB Special Connectors
Stanley
Model BJB Part No. Description Outside View Purposes
STCB1 47.302.2001.50 LED module block
coupler
・To connect modules
of the same pitch.
・This part is used for
straight connection
between LED
modules.
STCC2 47.342.3001 LED module coupler
w/sin gle w i r e s
・To connect
modules.
・When modules are
separately installed,
a maximum 50 mm
separation distance
is allowable.
STCC1 47.342.2001.50 LED module
connector w/ dou ble
wires
・To connect module
and power supply.
Approx.
50 mm
2
2. GENERAL VIEWS, NAMES, DESCRIPTIONS
●
●●
●STW0101N (Warm wh ite, 30 L EDs)
●
●●
●STN0101N (White, 30LEDs)
Mount hole
Power supply connecting part (Coupling part)
LED
Pitch: 10mm
Coupling part
Guide hole, positioning hole (Round hole)
●
●●
●STW0201N (Warm wh ite, 15 L EDs)
●
●●
●STN0201N (White, 15 LEDs)
LED
Pitch: 20mm
Coupling part
Power supply connecting part (Coupling part)
Guide hole, positioning hole (Round hole)
Mount hole
3
3. INSTALLATION, CONNEC TION
Two or more Slim Stick S LED modules can be installed by joining them with special couplers. A heat sink
mounted LED module has superior reliability.
●
●●
●Installation Proced ure
(1) Installation with screws
Use M3 bolts (round head diameter < 0.7mm) for mounting LED module.
The LED module is equipped with one guide hole. Use this hole for positioning the LED module.
There ar e five mounting holes in additi on to the gui de hole. At least two hole s must be secure d with bolt s.
[NOT E] In t he case of 30 LE D types ( STW0101N, STN0101N) , pay att ention that the holes' lin e is
offset from the LE Ds' line.
(2) I nstallation with double-faced tape
The LED modules can be installed with double-faced tape. (Recommended tape: NITTO 5000N)
Guide hole
30 LEDs (STW0101N, STN0101N)
15 LEDs (STW0201N, STN0201N)
Guide hole
BJB coupler Screw
If the screw is secured without the above
spacer, the LED module will warp 2mm
stressing the part.
●
●●
●When plates are used: Plates (Thickness: 2mm)
Washers (Thickness: 2mm)
Offset : 0.7mm
Pay attention not to warp the Slim Stick S-Type while installing. A warped installation will
have shorter LED module life and low reliability.
When the spe cial BJB connector is used for coupling LD modules, a 2mm gap w ill exist due
to the coupler's thickness. To remedy this, a plate, washer or spacer of 2mm thickness mus
t
be used to mount the LED module with bolt.
W
ARNING
PWB
2mm
●
●●
●When washers are used:
2mm
2mm
＊ When a metal plate is used, the insulator mus
t
be placed between the back of the circ uit board
and the metal plate. Apply the appropriate
insulator such as vinyl tape to the metal pl ate.
4
●
●●
●Connecting Procedure
The connector has a projection for meshing with the LED module and guaranteeing polarity orientation.
Insert the connector properly orientated until a click sounds informing complete insertion into the LED
module.
■Power supplying part
■Module coupling part ＊Use STCC2 or STCB1 for coupling the LED modules.
＊Use STCB1 to install the LED modules of the same LED pitch.
Cord (Red)
Cord (Black)
Cord (Red)
Cord (Black)
STCC1
30 LEDs type
(STW0101N, STN0101N)
15 LEDs type
(STW0201N, STN0201N)
STCC1
30 LEDs type
(STW0101N, STN0101N)
15 LEDs type
(STW0201N, STN0201N)
STCB1
(
Set the flat surface up.
)
STCC2
The number of connector connections/disconnections must not exceed five.
30 LEDs type
(STW0101N, STN0101N)
15 LEDs type
(STW0201N, STN0201N)
●Coupling with ST CC2
●Coupling with ST CB1
5
4. INSTALLATION, CONNEC TION
Use a DC12V constant voltage power supply. Stanley recommends the following power supply.
The number of LED modules connected is limited by power supply capacity and LED module contact
capacity.
Model Recommended Power Supply Number of LED modules
connected
STW0201N, STN0201N
(15 LEDs type) COSEL PBA15F-12 8
COSEL PBA15F-12 5 STW0101N, STN0101N
(30 LEDs type) COSEL PBA30F-12 8
＊The aforementioned recommended power supplies have sufficient safe performance. However they are
not PSE certif ied.
＊The number of connectable LED modules can be limited by distance between power supply and LED
module or cable resistance.
5. CAUTIONS
(
1) Please do not bend when using and storing this unit, anytime. Should this product be
bent, it may crack in the soldering area, causing malfunction. Please check carefully tha
t
there will be no excessiv e stress on module in usage.
(
2) In order to prevent electrostatic breakdown at the time of a mounting, please be sure to
protect from any electrostati c ch arge within the reassembl i ng productio n pro cess.
(
3) Please advise especially the parts (light emitting diode, resistor, etc.) that are mounted in
the switching, the maintenance, etc. that it does not add to o much load.
(
4) Please be sur e t o t urn OFF the power source when a mounti ng and rem oval of thi s uni t .
(
5) When connect i ng to another unit or power source, do not reverse co nnect.
(
6) In real usage, take care not to allow any conductive touch parts to touch the solde
r
pattern and component part lea d on the surface of Slim Stick S-Type.
(
7) Please take measures to dustproof the unit, as any dust etc. will effects the quality o
f
output.
(
8) In this unit, please do not submit to strong impulse or vibration or do not scratch with
sharp things, such as an ed ged tool.
(
9) Please keep the temperature and Moisture during storage + usage within the limits
defined by the specification. Moreover, please avoid usage or storage in any environmen
t
exposed to the organic solvent, etching gas (gaseous chlorine and sulfuration gas), etc.,
or fire.
(
10
) When cleaning the LED module post installation, use air pressure to blow off dust o
r
softly wipe with dry cloth to remove dust. Non observance of this caution (such as wiping
with moistened cloth, cleaning with detergent, solvent or alcohol, etc.) will result in LED
lighting failure a nd/or short e r l ife.
If the LED modules are installed in an area needing frequent cleaning, cover the LED
modules wit h a tran sparent acrylic cover or equi valent.
(
11
) During real usage, constraints, such as an input voltage, an operating environment, etc.
(temperature and Moisture) defined by the specification, should be observed. If used
outside of specification, the unit may not be able to satisfy optical and the electric
characteristi cs defined by the speci f i cati on.
(
12
) The characteristics described in this specifications may be altered without previous
notice in order to impr ove the performance.
CAUTIONS
6
6.
APPLICATION EXAMPLES OF SLIM STICK S-TYPE LED MODULES
■
■■
■Bed side illumination ■
■■
■
Ambient illumina tion (Indirect lig hting)
■
■■
■Under counter illumination ■
■■
■Cabinet illumination
