KSD-O2Q002-002
1
SI5313-H / SI5313-H(B)
IRED
21
0.60 Max.
5.60~6.00
21
1.00 Min.
1.20 Min.
4.80~5.20
8.70~9.10
1.40 Max.
1.00 Min.
2.20~3.20
0.05 Typ.
23.00 Min.
2.54 Typ.
0.55 Max.
4.80~5.20
8.70~9.10
1.40 Max.
23.00 Min.
2.54 Typ.
0.60 Max.
0.05 Typ.
5.60~6.00
0.55 Max.
0.05 Typ.
i
Features
Colorless transparency lens type
5mm(T-1) all plastic mold type
Low power consumption
High radiant intensity
Applications
Light source for remote control devices
(This device should be only used at non- repetitive pulse mode)
Outline Dimensions unit : mm
PIN Connections
1. Cathode
2. Anode
STRAIGHT TYPE STOPPER TYPE : (B)
S
Se
em
mi
ic
co
on
nd
du
uc
ct
to
or
r
KSD-O2Q002-002
2
-
H / SI5313
-
H(B)
Absolute Maximum Ratings (Ta=25℃)
Characteristic Symbol Rating Unit
Power dissipation PD 145 mW
*1Forward current IF 100 mA
*2Peak forward current IFP 1 A
Reverse voltage VR 4 V
Operating temperature range Topr -25 85∼ ℃
Storage temperature range Tstg -30 100∼ ℃
*3Soldering temperature Tsol 260 for ℃10 seconds
*1. Avoid operating under continuous bias
*2.Duty ratio = 1/100, Pulse width = 0.1ms
*3.Keep the distance more than 2.0mm from PCB to the bottom of IRED package
Electrical / Optical Characteristics (Ta=25℃)
Characteristic Symbol
Test Condition Min.
Typ.
Max.
Unit
Forward voltage VF IF= 50mA - 1.3 1.45 V
Radiant intensity IE IF= 50mA 10 25 - mW/Sr
Peak wavelength P IF= 50mA - 950 - nm
Spectrum bandwidth Δλ IF= 50mA - 50 - nm
Reverse current IR VR=4V - - 10 uA
*4Half angle 1/2 IF= 50mA - 30 - deg
*4. 1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity
KSD-O2Q002-002
3
-
H / SI5313
-
H(B)
Characteristic Diagrams
Fig. 3 IF – Ta
0 80
Fig. 2 IE - IF
30
Forward Current IF [mA]
Ambient Temperature Ta [℃]
Relative Intensity [%]
Wavelength [nm]
Forward Voltage VF [V]
Forward Current IF [mA]
Forward Current IF [mA]
Fig. 5 Radiation Diagram
Radiant Intensity IE [mW/Sr]
Relative Radiant Intensity IE [%]
Fig. 1 IF - VF
Fig.4 Spectrum Distribution
KSD-O2Q002-002
4
SI5313
-
H / SI5313
-
H(B)
The AUK Corp. products are intended for the use as components in general electronic
equipment (Office and communication equipment, measuring equipment, home
appliance, etc.).
Please make sure that you consult with us before you use these AUK Corp. products
in equipments which require high quality and / or reliability, and in equipments which
could have major impact to the welfare of human life(atomic energy control, airplane,
spaceship, transportation, combustion control, all types of safety device, etc.). AUK
Corp. cannot accept liability to any damage which may occur in case these AUK Corp.
products were used in the mentioned equipments without prior consultation with AUK
Corp..
Specifications mentioned in this publication are subject to change without notice.