COMMUNICATIONS MODULES & SUBSYSTEMS
Key Features • Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Applications
• Telecommunications
• Metropolitan Area Networks
• Subscriber loop
• Intra-office SONET/SDH
• High bit-rate data communications
Compliance
• Telcordia GR-253-Core
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
NORTH AMERICA:800 498-JDSU (5378) WEBSITE:www.jdsu.comWORLDWIDE:+800 5378-JDSU
2
PH1 SERIES
Dimensions Diagram (Specifications in inches [mm] unless otherwise noted.)
FIBER PIGTAIL
39.37 NOM
[1 METER]
0.52 MAX
[13.2]
2.20 MAX
[56.1]
3.00 MAX
[76.5]
2X 1.20 MAX
[30.0]
0.525±0.010
[13.34±0.25]
Configuration A
Configuration C
FIBER PIGTAIL
41.73 NOM
[1.06 METER]
0.835±0.010
[21.21±0.25]
2X 1.10 MAX
[27.9]
3.50 MAX
[88.9]
3.31 MAX
[84.1]
2X 3.94 MAX
[100.1]
0.52 MAX
[13.2]
3
PH1 SERIES
Module Functional Block Diagram
(K 30) TxFIFOERR
(K27) TxFIFORES
(B30) TxLOCKERR
(K24) TxRESET
TxDin (15:0)
(G28, 29) TxPICLK
(J21, K21) TxRATESEL(1: 0)
(E28, 29) TxPCLK
(C28, 29) TxMCLK
(F30) TxREFSEL
(A28, 29) TxREFCLK
(H30) TxLINETIMESEL
Mux
10 Gb/s
Laser
Driver
EML
Laser
PLL
Laser
TEC
Control
Laser
Bias
Control
10 Gb/s Clock
Recovery PD Bias
Control
µC
De -Mux
10 Gb/s
CMU
RxDout (15:0)
(E13,14) RxPOCLK
(C13,14) RxMCLK
(B 15) RxLOCKERR
(A13,14) RxREFCLK
(B9) RxLCKREF
(B6) RxMUTEDout
(F15) RxREFSEL
Vdd2 (1.8 VDC optional)
Vdd (3.3Vdc)
Vcc (5VDC)
Vee ( -5.2Vdc)
GND
10 Gb/s Serial Optic Output
LsPOWMON (D18)
LsBIASMON (F18)
LsENABLE (F21)
TxTRACE (J29)
LsTEMPMON (D21)
LsTEMPALM (F27)
LsBIASALM (F24
ALMINT (H15)
I2CDATA (K18)
I2CCLOCK (K15)
I2CADD(2:0) (D9,6,3)
MOD_RESET (D12)
10 Gb/s Serial Optic Input
RxPOWMON (F3)
RxPOWALM (F6)
APDTEMPMON (H3)
(L1 version only)
RxRATESEL(1:0) (J3,K3)
RxMUTEPOCLK (K9)
T
IA
Jitter Filter Bypass
Configuration
F RAM
EEPROM
Re
g
ulator
Vdd2 (1.8VDC)
Vdd (3.3VDC)
Vcc (5VDC)
Vee ( -5.2Vdc)
1.8 V Supply Source
Configuration
T
ransmitter
Receiver
µC bus
PD
4
PH1 SERIES
PH1 (IR2) Specifications
Parameter Minimum Typical Maximum
Transmitter
Output power (EOL) -1 dBm 0.5 dBm 2 dBm
Extinction ratio (EOL) 8.2 dB - -
Tx spectral range 1530 nm - 1570 nm
Wavelength stability over operating temperature (BOL setup, 100 GHz option) -25 pm - 25 pm
Wavelength stability over operating temperature (EOL setup, 100 GHz option) -100 pm - 100 pm
Sidemode suppression ratio 30 dB - -
Spectral power density - - 0.1 mW/MHz
Jitter generation GR-253 compliant
Receiver
PIN input power {BER = 10-12} (EOL) -15.0 dBm -16.0 dBm -
Maximum overload: PIN receiver {BER = 10-12} (EOL) -1 dBm - -
Rx spectral range 1280 nm - 1600 nm
Jitter tolerance and jitter transfer GR-253 compliant
System optical return loss -27 dB - -
Optical Path
Optical path penalty at 1550 nm and with 1600 ps/nm dispersion - - 2 dB
Electrical
Operating case temperature -5 °C - 70 °C
TDM power dissipation with jitter filter - 5.0 W 7.0 W
TDM power dissipation without jitter filter - 4.8 W 6.8 W
DWDM power dissipation with jitter filter - 5.8 W 7.8 W
DWDM power dissipation without jitter filter - 5.6 W 7.6 W
PH1 (SR2) Specifications
Parameter Minimum Typical Maximum
Transmitter
Output power (EOL) -4 dBm -2.5 dBm -1 dBm
Extinction ratio (EOL) 8.2 dB - -
Tx spectral range 1530 nm - 1570 nm
Sidemode suppression ratio 30 dB - -
Spectral power density - - 0.1 mW/MHz
Jitter generation GR-253 compliant
Receiver
PIN input power {BER = 10-12} (EOL) -15.0 dBm -16.0 dBm -
Maximum overload: PIN receiver {BER = 10-12} (EOL) -1 dBm - -
Rx spectral range 1280 nm - 1600 nm
Jitter tolerance and jitter transfer GR-253 compliant
System optical return loss -27 dB - -
Optical Path
Optical path penalty at 1550 nm and with 1600 ps/nm dispersion - - 2 dB
Electrical
Operating case temperature -5 °C - 70 °C
TDM power dissipation with jitter filter - 5.0 W 7.0 W
TDM power dissipation without jitter filter - 4.8 W 6.8 W
