SPECIFICATION CONTROL DRAWING 44A112X TITLE TWO CONDUCTOR CABLE, SHIELDED, JACKETED, Dae oeMAR{4 Revision yy GENERAL PURPOSE, 600 VOLT This specification sheet forms a part of the latest issue of Raychem Specification 44. SHIELD - COPPER, COATING SAME AS ON CONDUCTOR EXCEPT TIN-COATED SHIELD WITH SILVER- COATED HIGH-STRENGTH ALLOY CONDUCTOR JACKET - RADIATION-CGROSSLINKED, MODIFIED PYF, COMPONENT WIRE - 44A011X S KES 7X hi (Ed I \ ROG OX TABLE |. CABLE CONSTRUCTION DETAILS CONDUCTOR | SHIELD JACKET OUTSIDE PART NUMBER AWG) SIZE THICKNESS DIAMETER MAXIMUM Vv : ; WEIGHT (AWG) (n.) (in.) (Ib/1000 ft) * 44A112X-24-* 713 44A112X-10-* TABLE IIl_ CABLE PERFORMANCE DETAILS BEND TESTING MANDREL DIAMETER WEIGHT PART NUMBER nch) (+ 3% (Ib) (+ 3%) 1 LIFECYCLE, IMMERSION AND COLD LIFECYCLE, IMMERSION AND ACCELERATEDAGING BEND ACCELERATED AGING 44A112X-12-* NOTE: Nominal values are for information only. Nominal values are not requirements. Users should evaluate the suftability of this product for their application. Specifications are subject to change without notice. TE Connectivity afso reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1f COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANGE WITH MIL-STD-681. HOWEVER, DUE TO LENGTH LIMITATIONS OF THE RAYCHEM PART NUMBER, AN ALTERNATIVE COLOR CODE MAY REPLACE MIL-STD-681 COLOR CODE DESIGNATORS. (EXAMPLE 901/802.." MAY BE REPLACED BY "Axxx".) OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER, AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER Page 1 of 2 DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL = IE Wire & Cable , & 501 Oakside Avenue Redwood City, CA 94063-3800 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN TE Gannectivity Phone: 1-800-227.8816 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID Fax: 1-650-361-6297Revision f SGD Number TE spccirication CONTROL DRAWING J] Page 2 of 27 gy 44A112X TE Connectivity CABLE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level ACCELERATED AGING: 300 + 3C for6 hours BLOCKING: 150+ 3C for 6 hours DIELECTRIC WITHSTAND: 2500 volts (rms), 60 Hz, 1 minute FLAMMABILITY: 30 seconds (maximum); 3 in. (maximum); no flaming of facial tissue IMMERSION: Diameter increase 5% (maximum); no cracking, no dielectric breakdown JACKET COLOR: White preferred JACKET CONCENTRICITY: 70% (minimum) JACKET ELONGATION AND TENSILE STRENGTH: Elongation, 200% (minimum) Tensile Strength, 4000 Ibf/in? (minimum) JACKET FLAWS: Spark Test, 1.5 kV (rms) Impulse Dielectric Test, 6.0 kV (peak) LIFE CYGLE: 200 + 3C for 168 hours LOW TEMPERATURE-COLD BEND: -65+ 2C for 4 hours SHIELD COVERAGE: 85% (minimum) VOLTAGE WITHSTAND TEST (Post Environmental) : 1000 volts (rms), 60 Hz, 1 minute PART NUMBER: The X in the part numbers on page 1 shall be replaced by the applicable conductor material designator as follows: 1 tin-coated copper 2 silver-coated copper 3 nickel-coated copper 4 silver-coated high strength copper alloy (AWG's 26-16 only} 6 nickel-coated high strength copper alloy (AWG's 26-20 only} The "*" in the part numbers on page 1 shall be replaced by color code designators with a slash separating component wire colors and a dash separating the component wire color from the jacket color. 1/ Example: AWG 20, tin-coated copper, black and white component wires; white jacket: 44A1121-20-0/9-9 1/ see footer section on page 1