8-Lead LFCSP Amplifier Evaluation Board User Guide
UG-919
One Technology Way • P. O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Universal Evaluation Board for Single, 8-Lead LFCSP Operational Amplifiers
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS. Rev. 0 | Page 1 of 6
FEATURES
Enables quick breadboarding/prototyping
User defined circuit configuration
Edge mounted subminiature version A (SMA) connector
provisions
Easy connection to test equipment and other circuits
GENERAL DESCRIPTION
The 8L LFCSP SINGLE AMP evaluation board aids in the
evaluation of single, 8-lead LFCSP operational amplifiers. The
8L LFCSP SINGLE AMP evaluation board is a bare board with
no components soldered on, which enables users to prototype a
variety of operational amplifier circuits. The 8L LFCSP SINGLE
AMP evaluation board supports any of the Analog Devices, Inc.,
single operational amplifiers with and without a dedicated
feedback pin in 8-lead LFCSPs.
The 6-layer evaluation board accepts edge mounted SMA
connectors on both inputs and outputs to allow an efficient
connection to test equipment and other circuitry.
Optimized power and ground planes ensure low noise and high
speed operation. Component placement and power supply
bypassing are optimized for maximum circuit flexibility and
performance. The evaluation board accepts 0402 or 0603 surface-
mount technology (SMT) components, 1206 bypass capacitors,
and 100 mil headers.
All components are placed on the primary side. No components
are placed on the secondary side.
8L LFCSP SINGLE AMP EVALUATION BOARD
IMAGES
14072-001
Figure 1. 8L LFCSP SINGLE AMP Evaluation Board, Primary Side
14072-002
Figure 2. 8L LFCSP SINGLE AMP Evaluation Board, Secondary Side
UG-919 8-Lead LFCSP Amplifier Evaluation Board User Guide
Rev. 0 | Page 2 of 6
TABLE OF CONTENTS
Features .............................................................................................. 1
General Description ......................................................................... 1
8L LFCSP SINGLE AMP Evaluation Board Images ...................... 1
Revision History ............................................................................... 2
Schematic, Assembly Drawings, and Board Layout ..................... 3
Board Assembly ................................................................................ 5
Power Supply Bypassing ...............................................................5
Evaluation Board Stack Up ..........................................................5
Ordering Information .......................................................................6
Bill of Materials ..............................................................................6
REVISION HISTORY
3/16—Revision 0: Initial Version
8-Lead LFCSP Amplifier Evaluation Board User Guide UG-919
Rev. 0 | Page 3 of 6
SCHEMATIC, ASSEMBLY DRAWINGS, AND BOARD LAYOUT
14072-003
EPAD
R6 R11
VEE
VCC
R5
3VN
VP
FB
VCC
VEE
CC
VO
PD
EPAD
CF
RF
R3
RTN
R1
R7
R8
RS
CL
R9
C7
V
INN
VEE
R10
VEE
VCC
PD
VCC VEE
C8
VOUT
C1
R4
R2
VINP
RTP
C3 C5 C2 C4 C6
4
2
8
5
1
6
7
Figure 3. 8L LFCSP SINGLE AMP Evaluation Board Schematic
UG-919 8-Lead LFCSP Amplifier Evaluation Board User Guide
Rev. 0 | Page 4 of 6
14072-004
Figure 4. Component Side Assembly Drawing
14072-005
Figure 5. Component Side Layout Pattern
14072-006
Figure 6. Circuit Side Assembly Drawing
14072-007
Figure 7. Circuit Side Layout Pattern
8-Lead LFCSP Amplifier Evaluation Board User Guide UG-919
Rev. 0 | Page 5 of 6
BOARD ASSEMBLY
POWER SUPPLY BYPASSING
Internal power planes provide adequate interplanar capacitance
for certain applications. The external bypass capacitors, C1 and
C2, provide additional high frequency bypassing at the amplifier
power pins. The C3, C4, C5, and C6 capacitors provide additional
board level bypassing.
EVALUATION BOARD STACK UP
This 6-layer FR4 board design provides optimized high speed
and low noise performance. The first ground layer is spaced to
provide a 50 Ω controlled impedance with the primary layer to
optimize high frequency performance.
The VCC layer is sandwiched with the GND layer to provide
mechanical stability and distributed interplanar capacitance
between VCC and GND.
The bottom three layers sandwich the VEE plane layers between
two GND layers, generating distributed interplanar capacitance.
TOP COPPER – SIGNAL
GND
VCC
GND
VEE
BOTTOM COPPER – GND
50Ω IMPEDANCE
SPACING
14072-008
Figure 8. Stack Up
UG-919 8-Lead LFCSP Amplifier Evaluation Board User Guide
Rev. 0 | Page 6 of 6
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Quantity Reference Designator Description
3 VINP, VINN, VOUT Side mount SMAs
4 C1, C2, C3, C4 0.1 μF capacitors
2 C5, C6 10 μF capacitors
2 CF, CL Capacitors, user defined
2 C7, C8 Capacitors, user defined
1 R9 Resistor, user defined
6 R1, R2, R3, R4, R7, R8 Resistors, user defined
3 R5, R6, R11 Resistors, user defined
4 RTP, RTN, RF, RS Resistors, user defined
1 R10 1 kΩ resistor
2 GND1, GND2 Test points
2 VEE, VCC 100 mil headers, 3 position
1 PD 100 mil header, 2 position
1 U1 Analog Devices, Inc., 8-lead LFCSP amplifier
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG14072-0-3/16(0)
