B65684A0000R049 - EPCOS - Product.Network

%BUB4IFFU%BUB4IFFU

Date: September 2006, November 2008

hereto and the information contained therein without EPCOS’ prior express consent is prohibited.

Ferrites and accessories

PM 62/49

Core and accessories

Series/Type: B65684, B65685

209/06

Please read Cau ti ons and warnings and

Import ant notes at the end of this document.

■To IEC 61247

■Particularly suitable for power transformers

and energy storage chokes

■Delivery mode: sets

Magnetic characteristics (per set)

Σ l/A = 0.191 mm–1

le= 109 mm

Ae= 570 mm2

Amin = 470 mm2

Ve= 62000 mm3

Approx. weight 280 g/set

Gapped

Ungapped

Material AL value

approx.

μeOrdering code

N27 315 ±3% 2.60 48 B65684A0315A027

630 ±3% 1.10 95 B65684A0630A027

Material AL value

μePV

W/set

Ordering code

N27 9200 +30/–20% 1400 < 9.5 (200 mT, 25 kHz, 100 °C) B65684A0000R027

N87 9200 +30/–20% 1400 < 5.8 (200 mT, 100 kHz, 100 °C) B65684A0000R087

FPM0024-2

> 29

< 28.5

4+1

48.8+1.5 1.2+0.2

62 2

ø5.4+0.2

ø25.5 0.8

33.4+0.8

49 0.4

B65684Core

PM 62/49

3 11/08

Please read Cau ti ons and warnings and

Import ant not es at the end of this document.

Coil former

Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085:

F max. operating temperature 155 °C), color code black

Valox 420-SE0 ® [E45329 (M)], GE PLASTICS B V

Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s

Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3.5 s

Winding: see Data Book 2007, chapter “Processing notes, 2.1”

Pins squared in the start-of-winding area.

Also available without solder pins.

Sections AN

mm2lN

mm AR value

μΩ Solder

pins Ordering code

1270 120 15.4 16 B65685B1016T001

1270 120 15.4 —B65685A1000T001

B65685Accessories

PM 62/49

409/08

Please read Cau ti ons and warnings and

Import ant not es at the end of this document.

Mounting assembly

■For chassis mounting1) or printed circuit boards

■The set comprises a yoke and a base plate

■Fixing nuts M3 and washers are supplied

Yoke

■Material: Brass clamping yoke (∅ 2.6 mm) with thread

Base plate

■Material: Aluminum (0.6 mm)

Ordering code

Complete mounting assembly including nuts and washers B65685A2000X000

1) On a chassis the coil former must be mounted with its solder pins upward.

B65685Accessories

PM 62/49

509/06

Ferrites and accesso ries

Cautions a nd w a rnings

Mechanical stress and mounting

Ferrite cores have to meet mechanical requirements during assembling and for a growing number

of applications. Since ferrites are ceramic materials one has to be aware of the special behavior

under mechanical load.

As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing

or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads

can cause cracks or failure of the ferrite cores.

For detailed information see Data Book 2007, chapter “General – Definitions, 8.1”.

Effects of core combination on AL value

Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent

that the initial permeabilit y is dependent on the stress state of the core. The higher the stresses are

in the core, the lower is the value for the initial permeability. Thus the embedding medium should

have the greatest possible elasticity.

For detailed information see Data Book 2007, chapter “General – Definitions, 8.2”.

Heating up

Ferrites can run hot during operation at higher flux densities and higher frequencies.

NiZn-materials

The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.

Processing notes

– The start of the winding process should be soft. Else the flanges may be destroid.

– To strong winding forces may blast the flanges or squeeze the tube that the cores can no more

be mount.

– To long soldering time at high tem perature (>300 °C) may effect copl anarity or pin arrangement.

– Not following the processing notes for soldering of the J-leg terminals may cause solderability

problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation

of the wire. For detailed information see Data Book 2007, chapter “Processing notes, 2.2”.

– The dimensions of the hole arrangement have fixed values and should be understood as a

recommendation for drilling the printed circuit board. For dimensioning the pins, the group of

holes can only be seen under certain conditions, as they fit into the given hole arrangement. To

avoid problems when mounting the transforme r, the manufacturing tolerances for positioni ng the

customers’ drilling process must be considered by increasing the hole diameter.

6 11/08

Important no tes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical

requirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application.

As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with

them than the cu stomers themsel ves. For these reasons , it is always ul timately incumbent on the

customer to check and decide whether an EPCOS product with the properties described in the

product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or failure

before the end of their usual service life cannot be completely ruled out in the current state

of the art, even if they are operated as specified. In customer applications requiring a very

high level of operational safety and especially in customer applications in which the malfunction

or failure of a passive electronic component could endange r human life or heal th (e.g. in acciden t

prevention or life-saving systems), it must therefore be ensured by means of suitable design of

the customer application or other action taken by the customer (e.g. installation of protective

circuitry or redundancy) that no injury or damage is sustained by third parties in the event of

malfunction or failure of a passive electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our

Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more

detailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order.

We also reserve the right to discontinue production and delivery of products.

Consequently, we cannot guarantee that all products named in this publication will always be

available.

The aforementioned does not apply in the case of individual agreements deviating from the

foregoing for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current version

of the “General Terms of Delivery for Products and Services in the Electrical Industry”

published by the German Electrical and Electronics Industry Association (ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,

MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD,

SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered

or pending in Europe and in other countries. Further informati on will be found on the Internet at