Series MB2400 Toggles Electrical Capacity (Resistive Load) Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons General Specifications Rockers Snap-Action Pushbuttons C Power Level (silver): Logic Level (gold): Logic/Power Level: (gold over silver) Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel Materials & Finishes Plunger: Bushing: Frame: Case: Base: Movable Contactor: Movable Contacts: Stationary Contacts: Terminals: Supplement Accessories Indicators Touch Tilt Tactiles Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Installation Mounting Torque: Cap Installation Force: Soldering: Cleaning: 3A @ 125V AC 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. 20 milliohms maximum for silver; 30 milliohms maximum for gold 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 200,000 operations minimum 25,000 operations minimum for silver; 100,000 operations minimum for gold Single pole 2.45N; double pole 3.92N Pretravel .024" (0.6mm); Overtravel .016" (0.4mm); Total Travel .039" (1.0mm) Brass with nickel plating Brass with nickel plating Stainless steel Polybutylene terephthalate (PBT) (UL94V-0) Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver alloy with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Copper or brass with silver plating; copper or brass with gold plating -30C through +85C (-22F through +185F) 90 ~ 95% humidity for 96 hours @ 40C (104F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 3 shocks in each direction) 1.5Nm (13.0 lb * in) for double nut; 0.7Nm (6.0 lb * in) for single nut 80.0N (18.0 lbf) maximum downward force on actuator Wave Soldering (PC version): See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. These devices are not process sealed. Hand clean locally using alcohol based solution. See Cleaning Specifications in Supplement section. Standards & Certifications Flammability Standards: UL94V-0 case & base UL: File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" or "/CUL" before dash in part number to order UL recognized switch. All single and double pole models recognized at 3A @ 125V AC or 0.4VA max. @ 28V DC max. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" before dash in part number to order CSA certified switch. Single pole models with PC, solder lug, or Wirewrap terminals & double pole with PC or Wirewrap terminals certified at 3A @ 125V AC or 0.4VA @ 28V maximum. C96 www.nkkswitches.com Toggles Series MB2400 Rockers Distinctive Characteristics Snap-acting mechanism gives smooth actuation, short stroke, light touch, and audible feedback. This mechanism also provides long mechanical life. C Programmable Illuminated PB High torque bushing construction prevents rotation or separation from frame during installation. Pushbuttons Snap-Action Pushbuttons Antijamming design protects contacts from damage due to excessive downward force on the actuator. Keylocks Compatible companions with M series toggles. Body, bushing, and footprint dimensions ideal for mounting MB2400 pushbuttons and M toggles next to one another. Stainless steel frame resists corrosion. Rotaries Longer center solder lug terminal simplifies wiring and soldering. Slides Silver contacts of specially composed alloy for hardness. Tactiles Epoxy sealed terminals prevent entry of solder flux and other contaminants. Tilt Prominent external insulating barriers increase insulation resistance and dielectric strength. Page C98 Bracket PC Mount Page C102 Snap-in Mount Page C108 Accessories Indicators Touch Bushing Mount www.nkkswitches.com C97 Supplement Actual Size Toggles Series MB2400 TYPICAL SWITCH ORDERING EXAMPLE Rockers Pushbuttons Programmable Illuminated PB Keylocks Rotaries 11 MB24 C E1 Poles & Circuits 11 61 SPDT DPDT ON (ON) ON W 01 Contact Materials & Ratings (ON) W G Gold Rated 0.4VA max @ 28V AC/DC max A Gold over Silver Rated 3A @ 125V AC & 0.4VA max @ 28V AC/DC max Bushings F Caps Silver Rated 3A @ 125V AC ( ) = Momentary E1 .285" (7.24mm) Threaded with D Flat E2 .285" (7.24mm) Smooth with D Flat A1 .280" (7.1mm) Threaded with Keyway A2 .280" (7.1mm) Smooth with Keyway 01 Solder Lug 03 .250" (6.35mm) Straight PC S1 .350" (8.9mm) Threaded with Keyway 05 .425" (10.8mm) Wirewrap .350" (8.9mm) Smooth with Keyway 06 .750" (19.05mm) Wirewrap S2 07 .964" (24.5mm) Wirewrap Tactiles Slides Snap-Action Bushing Mount Pushbuttons F .201" (5.1mm) Diameter H .295" (7.5mm) Diameter Cap Colors A Black B White C Red Terminals IMPORTANT: Tilt Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators MB2411E1W01-FA Accessories Black .201" (5.1mm) Diameter Cap SPDT ON-(ON) Circuit Supplement Silver Contacts with 3-Amp Rating C98 www.nkkswitches.com .285" (7.24mm) Threaded Bushing with D Flat Solder Lug Terminals A Series MB2400 Toggles Snap-Action Bushing Mount Pushbuttons POLES & CIRCUITS Note: Terminal numbers are not actually on the switch. SP MB2411 ON (ON) 1-3 1-2 SPDT DP MB2461 ON (ON) 1-3 4-6 1-2 4-5 DPDT Keyway Rockers Down Model Keyway 1 (COM) 3 2 4 Programmable Illuminated PB 1 (COM) 3 C 2 5 6 BUSHINGS Note: Plunger selection is not required for MB2400 pushbuttons. The plunger can be used with or without a cap. (8.0) Dia .315 (2.5) .098 (5.54) (7.24) .218 .285 E2 .285" (7.24mm) Smooth with D Flat (6.2) Dia .244 (2.84) Dia .112 (8.0) Dia .315 .280" (7.1mm) Smooth with Keyway (5.54) (7.24) .218 .285 (0.9) .035 .350" (8.9mm) Smooth with Keyway (6.2) Dia .244 (2.84) Dia .112 (8.0) Dia .315 (5.54) (7.1) .218 .280 (8.9) .350 Maximum Panel Thickness with Standard Hardware: .134" (3.40mm) (0.8) .031 (2.5) .098 (0.9) .035 (5.54) .218 S2 (6.2) Dia .244 (2.84) Dia .112 (8.0) Dia .315 (2.5) .098 (2.5) .098 (0.9) .035 Maximum Panel Thickness with Standard Hardware: .068" (1.74mm) (0.8) .031 1/4-40 Thd (2.84) Dia .112 (8.0) Dia .315 (2.5) .098 (5.54) (7.1) .218 .280 A2 .350" (8.9mm) Threaded with Keyway (0.8) .031 1/4-40 Thd (2.84) Dia .112 (0.9) .035 Maximum Panel Thickness with Standard Hardware: .068" (1.74mm) S1 Keylocks (0.8) .031 1/4-40 Thd (2.84) Dia .112 (8.0) Dia .315 .280" (7.1mm) Threaded with Keyway A1 Tactiles .285" (7.24mm) Threaded with D Flat Tilt E1 (2.5) .098 (0.9) .035 (5.54) .218 (8.9) .350 (0.9) .035 (0.6) .024 (6.5) Dia .256 (5.8) .228 (6.5) Dia .256 (2.2) Dia .087 Accessories (5.8) .228 With Optional Locking Ring (6.1) .240 Supplement (6.5) Dia .256 For E1 or E2 Bushing with D Flat Indicators Panel Cutouts For A1, A2, S1, or S2 Bushing with Keyway Standard hardware includes 2 hex nuts & 1 lockwasher. Hardware is illustrated following the Typical Switch Dimension drawings. www.nkkswitches.com Pushbuttons Normal Pole Rotaries Down Throw & Switch Schematics Slides Normal Connected Terminals Touch Plunger Position ( ) = Momentary C99 Toggles Series MB2400 Keylocks Programmable Illuminated PB Pushbuttons Rockers CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 3A @ 125V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum C Note: Complete explanation of operating range in Supplement section. A Power Level or Logic Level Gold over Silver 3A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section for complete explanation of dual rating and operating range. TERMINALS 01 03 Solder Lug (4.0) .157 Rotaries Epoxy Seal Slides Snap-Action Bushing Mount Pushbuttons .250" (6.35mm) Straight PC Epoxy Seal (2.0) .079 (2.0) (1.1) .079 .043 Thk = (0.8) .031 (1.17) .046 Thk = (0.8) .031 Wirewrap or Extended PC 05 .425" (10.8mm) (4.8) .189 Tactiles Epoxy Seal 06 3 A .750" (19.05mm) Refer to footprints if using as extended PC terminal. (1.27) .050 Tilt (6.35) (4.8) .250 .189 07 .964" (24.5mm) Dimension A = terminal lengths as shown beside the code boxes at left. Thk = (0.8) .031 2 (4.7) Typ .185 1 3 6 2 5 1 4 (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole Double Pole AT475 .201" (5.1mm) Diameter Cap H (5.1) Dia .201 (6.4) .253 (4.0) .157 AT496 .295" (7.5mm) Diameter Cap Material: Polyamide Material: Polyamide Finish: Glossy Finish: Glossy Cap Colors Available: Supplement Accessories Indicators Touch CAPS & CAP COLORS F C100 A Black B www.nkkswitches.com White (7.5) Dia .295 (6.4) .253 C Red (4.7) Typ .185 (4.0) .157 Toggles Series MB2400 Snap-Action Bushing Mount Pushbuttons TYPICAL SWITCH DIMENSIONS NC (4.7) Typ .185 1/4-40 Thd (6.4) .253 (7.24) .285 (0.9) (4.5) .035 .177 (14.0) .552 3 NO C 2 COM 1 (4.0) .157 (2.0) .079 (7.9) .311 MB2411E1W01-FA (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 (2.4) .096 (5.1) Dia .201 (2.84) Dia .112 (13.0) .512 (4.7) Typ .185 1/40-40 Thd (6.4) .253 (7.24) .285 (0.9) (4.5) .035 .177 (14.0) .552 NC 6 3 NO 5 2 COM 4 1 (4.0) .157 (4.8) .189 (12.7) .500 Rotaries Flat Solder Lug Keylocks Double Pole Pushbuttons (13.0) .512 Programmable Illuminated PB (1.1) x (2.0) Typ .043 x .079 (0.8) Typ .031 (2.4) .096 (5.1) Dia .201 (2.84) Dia .112 (2.0) Typ .079 MB2461E1W01-FA Slides Flat Solder Lug Rockers Single Pole Tactiles HARDWARE Standard Hardware AT509 Lockwasher (8.0) .315 1 included with each switch Material: Brass with Nickel Plating (9.0) .354 Material: Steel with Zinc/Chromate (1.5) .059 (0.5) .020 Touch 2 included with each switch (6.4) Dia (10.2) Dia .252 .402 Tilt 1/4-40 Thd AT513H Inch Threaded Hexagon Nut Material: Steel with Zinc/Chromate Material: Steel with Zinc/Chromate (5.8) .229 (1.7) .067 (0.8) .031 (6.2) Dia .244 (2.0) .079 (1.68) .066 www.nkkswitches.com (5.5) .217 (12.0) Dia .472 Accessories (12.0) Dia .472 (2.0) .079 AT515 Locking Ring for E1 Bushing Supplement AT507H Locking Ring for A1 or S1 Bushing (6.35) Dia .250 Indicators Optional Hardware (0.8) .031 C101