APE12M05 Non-isolated Product Te c h n i c a l R e f e r e n c e N o t e s 5V Input, 1.5V Output 18W DC-DC Converter (Rev01) -1TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 Publishing Date: 20020701 APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Introduction Feature APE12M05 is double structure non-isolated 1. Wide operating environment temperature DC-DC module featuring high efficiency up to range ( 0-25 C with natural convection ) 84%. 2. High efficiency: 84% typical APE12M05 comes in 5V input version and is capable of providing up to 18W of output power in a small size 2.0in. x 1.0in. x 0.475in. The module uses a 4.5V to 5.5 V input range and 3. High power density 4. Low output noise 5. Nonisolated output provides 1.5V output voltage with 12A output 6. Small size: 50.8mm x 25.4mm x 12.1mm current. APE12M05 features high efficiency, high power density, wide operating environment tempera- ( 2.0in. x 1.0in. x 0.475in. ) 7. Remote sense ture range, and easy installation. The typical 8. Trim function: 90% - 110% Vo efficiency is 84% and the power density is 18.9W/inch3. The operating environment tem- 9. Over-current protection perature is 25 C with natural convection. With adjustable output, remote sense, OCP, the Applications product is especially suitable for Telecom, Datacom, work station, severs and distributed 1. Distributed power architecture power supply systems. The APE12M05 is designed to meet CISPR22, FCC Class A, UL, TUV, and CSA certifications. 2. Servers 3. Workstations 4. Desktop computers TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -2www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Typical Application C1 C2 Vin Vin Vout C3 C4 Load GND C1 C2 C3 C4 : Recommended 1200F Electrolytic Capacitor : Recommended 4.7F Ceramic Capacitor : Recommended 4.7F Ceramic Capacitor : Recommended 1200F Electrolytic Capacitor Block Diagram Current Detecting +Vin +Vout GND GND OCP Driving Sense PWM Trim + Vref Pin Location (Component-side view) -Vin -Vout -Vsense Ground No conn. No conn. Trim +Vsense +Vout +Vin TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -3www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Absolute Maximum Rating Characteristic Min Typ Input Voltage(continuous) Input Voltage(peak/surge) Operating temperature storage temperature Max Units 6 Vdc 7 Vdc 0 25 C -40 125 C Notes 100ms non-repetitive Natural convection Input Characteristics Characteristic Min Typ Max Units Input Voltage Range 4.5 5 5.5 Vdc Input Reflected Current (p-p) 4 10 %Iin Shortcircuit Current 1.5 2 A Input Current 4.2 APE12M05 Output Characteristics Characteristic Min Typ Power 18 A Max Units Notes Actual testing value < 4.6A Notes W Output Current 12 A Line Regulation 1 %Vo Vin=4.5~5.5V, Io=12A Load Regulation 1 %Vo Io=0~12A, Vin=5V Efficiency 83 84 % Dynamic Response 50%-100% load 100%-50% load TEL: FAX: USA 1-760-930-4600 1-760-930-0698 30 50 mV Ta=25 C , DI/Dt=1A/10s 120 300 s Ta=25 C , DI/Dt=1A/10s 30 50 mV Ta=25 C , DI/Dt=1A/10s 120 300 s Ta=25 C , DI/Dt=1A/10s Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -4www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output APE12M05 Output Characteristics ( continued ) Characteristic Min Current Limit Threshold 13.2 Output Setpoint Voltage -1 Trim Range -10 Sense Compensation Typ 0 Max Units 16.8 A +1 %Vo +10 %Vo 0.25 Temperature Coefficient Notes Vin=5V, Io=12A V 0.03 %Vo/C 9 18 mV ( 0 to 20MHz BW ) Noise (p-p) 30 50 mV ( 0 to 20MHz BW ) Switching Frequency 290 Ripple (rms) General Specifications Characteristic Min MTBF Typ kHz Max 1,800 Pin solder temperature 260 Hand Soldering Time 5 Weight 27 Units Notes k Hrs Bellcore TR332, 25 C C s wave solder < 10 s iron temperature 425 C grams Ordering Information Model Number APE12M05 TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Input Voltage Iin ( typ ) Output Voltage Output Current Efficiency typ Ripple (mV rms) 5V 4.2A 1.5V 12A 84 9 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 Noise (mV pp) 30 -5www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Ef ficiency Characteristic Curves Typical Output Characteristics APE12M05 Typical Efficiency APE12M05 4.5V 90 (at 25C) 5V 1.6 88 5.5V 1.4 5.5V 84 Efficency(%) Output Voltage(V) 86 82 80 78 5V 1.2 1.0 4.5V 0.8 76 0.6 74 0 2 4 6 8 10 12 12 Typical Output Ripple Voltage ( 12A Output ) APE12M05 TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 13 14 15 16 17 Output Current(A) Output Current,Io(A) Typical Start-Up Transient(5V Input,12A Output) APE12M05 Asia 852-2437-9662 852-2402-4426 -6www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Power Derating Power Derating vs. Local Ambient Temperature and Air Velocity APE12M05 Percent of Maximum Output Power 100 80 60 40 20 0 0 Natural Convection 10 20 30 40 50 60 70 80 90 100 110 120 Ambient Temperature T A ( C) TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -7www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Input Characteristics The APE12M05 power module has no internal fuse. An external fuse must always be employed! To meet international safety requirements, an input line fuse should be used. Input wires and copper coil must be capable of conducting a current of 1.5 times the value of the fuse. If one of the input lines is connected to chassis ground, then the fuse must be placed in the other input line. A fuse with ratings of 10A is recommended for APE12M05. Output T rimming Output can be externally trimmed by using either method shown in figure 2. Users can increase or decrease the output voltage set point of a module by connecting an external resistor between the TRIM pin and either the +Vout or GND pins. The trim resistor should be positioned close to the module. If not using the trim feature, leave the TRIM pin open. Trimming up or down by more than 10% of the nominal output may cause the converter to work improperly. J1 PIN 3 Output Characteristics Trim up J2 PIN 9 Remote Sensing When the load can not be placed close to converter output pin, voltage drop will occur in distribution. This voltage drop can be compensated using sense lead. As shown in figure 1, connecting sense pin close to the load, when the load changes, the module will automatically adjust the real output to maintain the constant voltage on the load. If not using the remote sense pin, leave it open. Trim down J1 PIN 4 Rtrim up = 10 Vo up - 1.5 Rtrim down = 20 - 20 Vo down - 1 - 20 3 - 2 Vo down Where: Rtrim up is trimming up resistance; Rtrim down is trimming down resistance; Vo up is trim up voltage; Vo down is trim down voltage; Rline R is in kohms. +Vout Fig.2 Output Voltage Set-point Adjustment +Sense Load -Sense Rline -Vout Fig.1 Sense Connection TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Output Over-Current Protection APE12M05 features current limiting with a threshold is between 13.2A and 16.8A. The module can not tolerate short circuit conditions in a long time. When the overcurrent condition is removed, the converter will automatically restart. Asia 852-2437-9662 852-2402-4426 -8www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Safety Considerations For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL1950, CSA C22.2 No. 950-95, and VDE 0805 (EN60950, IEC950). For the module's output to be considered meeting the requirements of safety extra-low voltage (SELV), one of the following must be true: 1. All inputs are SELV and floating, with the output also floating. 2. All inputs are SELV and grounded, with the output also grounded. 3. Any non-SELV input must be provided with reinforced from any other hazardous voltages, including the ac mains, and must have a SELV reliability test performed on it in combination with the converters. Inputs must meet SELV requirements. If the input meets extra-low voltage (ELV) requirements, then the converter's output is considered ELV. The input to these units is to be provided with a maximum 10A normal blow fuse in the ungrounded lead. parallel with the air-flow direction. Soldering APE12M05 is compatible with standard wave soldering techniques. When wave soldering, the converter pins should be preheated for 2030 seconds at 110 C, and wave soldered at 260 C for less than 10 seconds. When hand soldering, the iron temperature should be maintained at 425 Cand applied to the converter pins for less than 5 seconds. Longer exposure can cause internal damage to the converter. Cleaning can be performed with cleaning solvent IPA or with water. Mechanical Chart See Fig. 3. next page. Dimensions are in millimeters Component-side footprint. (inches). APE12M05 Mechanical Considerations Thermal Performance APE12M05 can work properly under natural convection in ambient temperature up to 25 C. If air-flow is applied, it can work in a much wider temperature range( See derating curves for reference ). In order to maintain efficient heat dissipation, the converters should be mounted TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -9www.astec.com APE12M05 Non-Isolated DC/DC Converter 5V Input, 1.5V Output Tolerances: Inches .xx !0.020 .xxx !0.010 Pins >4mm <4mm Millimeters .x !0.5 .xx !0.25 !0.02inch ( !0.5mm) !0.01inch ( !0.25mm) Fig.3 APE12M05 Mechanical Chart Pin Function 1 2 3 4 5 6 7 8 9 10 -Vin +Vin -Vout +Vout -Vsense Ground No conn* No conn Trim +Vsense * In IPD module, this is Loop comp pin. when External capacitor exceeds 20000F, connect this pin to ground, else leave it floating. APE12M05 cancles the function. TEL: FAX: USA 1-760-930-4600 1-760-930-0698 Europe 44-(0)1384-842-211 44-(0)1384-843-355 Asia 852-2437-9662 852-2402-4426 -10www.astec.com PART NUMBER DESCRIPTION ss pp c - 0 iv L - iv = Input Voltage 05 = Range centered on 5V 12 = Range centered on 12V 24 = 18 to 36(2:1), 9 to 36V(4:1) 36 = 20 to 60V 46 = 18V to 75V (4:1) 48 = Typ 36 to 75V xxx f yy h n - p - mx-Options p = Pin Length Omit this digit for Standard 5mm 6 = 3.8mm, 7= 5.8mm 8 = 2.8mm Enable Logic Polarity Omit for Positive Enable Logic N = Negative Enable Except: AK60C-20H, BK60C-30H Omit for Negative Logice P = Positive Logic c = Pinout compatability A= Astec Footprint or "non Lucent" footprint C= Ind Std, Exact Lucent drop in pp = Package Type 40 = 1" x 2" SMD 42 = 1.5" x 2" SMD 45 = 1.45" X 2.3" (1/4 Brk) 60 = 2.4" X 2.3" (1/2 Brk) 80 = Full size 4.6" x 2.4" 72= 2.35" X 3.3 (3/4 Brk) H = High Efficiency (Synch rect.) Omit H if Conventional Diode (low Eff) yy = Output Current ie. 08 = 8 Amps f = # of Outputs F = Single Output D = Dual Output xxx = Output Voltage Format is XX.X (ie 1.8V = 018) ss = Series AA = 1/2brick Dual (Old designator) mx = Options M1,M2 = .25" Height Heatsink M3,M4 = .5" height Heatsink M5.M6 = 1.0" Height Heatsink AK = Ind Std sizes (1/4, 1/2, full) <150W AM/BM = Full size, astec pin out AL = Half size, astec pin-out BK = Ind Std size =>150W or feature rich AV = Avansys Product Note: For some products, they may not conform with the PART NUMBER DESCRIPTION above absolutely. REVISION Q ATTACHMENT I Page 1 of 2 NEW PART NUMBER DESCRIPTION A c s ii V1 V2 V3 Output Voltage A = 5.0V F = 3.3V G = 2.5V D = 2.0V / 2.1V Y = 1.8V M = 1.5V K = 1.2V J = 0.9V Vin - e t p Mx E = 7.5V B = 12V, C = 15V L = 8V, H = 24V, R = 28V Omit V2 and V3 if Single Output Omit V3 if Dual Output ie for Dual Output 5 and 3.3V V1 =A, V2 = F, V3 =Omit V1 =A, V2 = F, V3 =Omit ii = Output Current Max ie 60 = 60 Amps Vin = Input Voltage range 300 = 250V to 450V 48 = 36V to 75V 24 = 18V to 36V 03 = 1.8V to 5.0V 08 = 5.0V to 13.0V PFC: Power Factor Corrected S = Size F = Full Brick H = Half Brick Q = Quarter Brick S = 1 X 2 18 Pin SMT E = 1 X 2 Thru Hole C = (.53X1.3X.33) SMT (Austin Lite drop in) V = Conventional Package (2X2.56") or ( A = SIP W = Convent pkg (Wide 2.5X3) R = 1 X 1 Thru Hole A = SIP T = 1.6 X 2 E = Enable Logic for > 15W Omit this digit for Positive enable N = Negative Logic E = Enable Logic for < 15W Omit this digit for no enable option 1 = Negative Logic 4 = Positive Logic c = Construction E = Enhanced Thermals (Baseplate or adapter plate) I = Integrated (Full Featured) Hong Kong models L = Low Profile (Open Frame, No case - Isolated) P = Open Frame (SIP or SMT) non-isolated Trim for 1W to 15W 9 = Trim Added P = Pin Length Omit this digit for Standard 5mm 6 = 3.8mm 8 = 2.8mm 7 = 5.8 mm Mx - Factory Options customer Specific Note: For some products, they may not conform with the NEW PART NUMBER DESCRIPTION above absolutely. REVISION Q ATTACHMENT I Page 2 of 2