Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS Product information in this catalog is as of October 2011. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that Taiyo Yuden Co., Ltd. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. Please contact Taiyo Yuden Co., Ltd. for further details of product specifications as the individual specification is available. Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact Taiyo Yuden Co., Ltd. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called"TAIYO YUDEN' s official sales channel"). It is only applicable to the products purchased from any of TAIYO YUDEN's official sales channel. Please note that Taiyo Yuden Co., Ltd. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. Taiyo Yuden Co., Ltd. grants no license for such rights. Caution for export Certain items in this catalog may require specific procedures for export according to"Foreign Exchange and Foreign Trade Control Law"of Japan,"U.S. Export Administration Regulations", and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 12 notice_e-01 LEADED FERRITE BEAD INDUCTORS WAVE FEATURES APPLICATIONS Use of high loss ferrite material. Waveform correction of digital signals from digital equipment and absorption of high-frequency noise from data lines. Easy mounting on PC boards. Available in a wide range of values and configurations to suit most applications. OPERATING TEMP. 2585 ORDERING CODE F B FB A 0 H Type Ferrite Beads A R 4 4 5 Core Dimensions mm 03 2.5 04 3.5 05 5.0 06 6.0 07 7.5 Configuration Axial lead A 0 B Material code HA Refer to impedance curves for material VA difference B Nominal Impedance 00 example 850 121 Internal code Standard Products 85 120 Excluding 03Type Lead configurationmm Straight lead (26mm lead space) / ammo SA Straight lead (FBR05 type) / ammo Straight lead (52mm lead space) / ammo SB Straight lead (FBR07 type) / ammo Formed lead (10mm pitch) / bulk TB Straight lead (FBR07 type) / ammo Formed lead (12.5mm pitch) / bulk UB Radial lead formed / ammo Formed lead / bulk (15.0mm pitch) / bulk US Formed lead (crimped) / bulk Lead (2.5mm pitch)/bulk (FBR) VB Dual side lead formed (crimped) / ammo NA Straight lead / bulk (FBA) VS Formed lead / bulk NB Formed lead (crimped) / bulk AB BB KD KE KF Radial lead EXTERNAL DIMENSIONS/STANDARD QUANTITY Configurations Type Taping Straight Dimensions Bulk Formed Straight 0 3H A450 - 0 0 0 3V A 4 5 0 - 0 0 D Formed 2.50.2 F: 10, 12.5, 15 (0.39, 0.492, 0.591) (0.0980.008) P: 12.7 (0.500) 4.50.3 (0.1770.012) Type FBA03 F: 5.0 (0.197) 0 4H A4 50 - 0 0 0 4V A 4 5 0 - 0 0 3.50.2 (0.1380.008) 4.50.3 (0.1770.012) 3.50.2 F: 10, 12.5, 15 (0.39, 0.492, 0.591) (0.1380.008) 6.00.5 0 (0.2360.020 ) 0 F: 10, 12.5, 15 (0.39, 0.492, 0.591) Lead Configuration Bulk Taped Ammo NA, KD, US 1000 KE, KF, VS 500 AB, BB 2000 UB, VB 3000 NA, KD, US 1000 KE, KF, VS 500 AB, BB 1000 UB, VB 3000 NA 1000 SA 2000 NA 1000 NB 1000 SB 2000 F: 5.0 (0.197) P: 12.7 (0.500) FBA Standard Quantity (pcs) L 0 4H A6 0 0 - 0 0 0 4V A 6 0 0 - 0 0 04H A9 0 0 - 0 0 0 4V A 9 0 0 - 0 0 F: 12.5, 15 (0.492, 0.591) 3.50.2 (0.1380.008) 9.00.5 (0.3540.020) 5.0 max. (0.197 max.) 7.5 (0.295) FBA04 P: 12.7 (0.500) 0 5 V A12 1 - 0 0 P: 12.7 (0.500) 06H A850N A -00 06V A850N A - 00 FBR F: 2.5 (0.098) 6.00.5 (0.2360.020) 06H A121N A - 0 0 0 6V A121N A - 0 0 F: 2.5 (0.098) 07H A 8 50 - 0 0 07 V A 8 5 0 - 0 0 07 H A121 - 0 0 0 7 V A12 1 - 0 0 P: 12.7 0.500 FBR05 F: 5.0 (0.197) 7.50.5 (0.2950.020) 2.0 H: SB 18 0 TB 16 0.5 5.0 (0.197) FBR06 7.0 (0.276) 5.5 (0.217) FBR07 7.5 (0.295) Please specify the lead configuration code. Note: Lead diameter (d) shall fall within a range of 0.65mm0.05mm, FBR05, and FBR07 types however, will have a lead diameter (d) range of 0.6mm0.05mm. Unitmminch This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. 150 12 leaded_i04_e-01 PART NUMBERS Ordering code FBA FBR 03 04 04 04 05 06 06 07 07 450 00 450 00 600 00 900 00 VA 121 00 850 NA 00 121 NA 00 850 00 121 00 EHS (Environmental Hazardous Substances) RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS Impedance [] min. 35.0 45.0 60.0 90.0 120.0 85.0 120.0 85.0 120.0 Measuring frequency [MHz] Material HA VA 50 100 50 100 50 100 50 100 100 50 100 50 100 50 100 50 100 Rated Current [A] max. Material HA VA 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 7.0 Please specify material codes (HA,VA) and lead configuration code. DC Resistance : 0.01 max., Insulation resistance : 1.0M min. ELECTRICAL CHARACTERISTICS IMPEDANCE-vs-FREQUENCY CHARACTERISTICS Measured by HP4191A FERRITE BEAD INDUCTORS NOISE SUPPRESSION COMPONENTS This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. leaded_i04_e-01 12 151 PACKAGING Minimum Quantity Type Lead Configuration NA, KD, US KE, KF, VS AB, BB UB, VB NA, KD, US KE, KF, VS AB, BB VB, UB FBA03 FBA04 Standard quantity [pcs] Taped Bulk Ammo 1000 500 2000 3000 1000 500 1000 3000 Type Lead Configuration NA SA NA NB SB FBR05 FBR06 FBR07 F L1 d 10.01.0 4.50.3 (0.3940.040) (0.1770.012) 3.50.2 (0.1380.008) 10.01.0 4.50.3 (0.3940.040) (0.1770.012) FBA04600 3.50.2 (0.1380.008) 6.00.5 10.01.0 0 (0.3940.040) (0.2360.020 ) 0 7.52.0 (0.2950.079) FBA03450 2.50.2 (0.0980.008) 12.51.0 4.50.3 (0.4920.004) (0.1770.012) 7.02.0 (0.2760.079) 3.50.2 (0.1380.008) 12.51.0 4.50.3 (0.4920.004) (0.1770.012) FBA04600 3.50.2 (0.1380.008) 12.51.0 (0.4920.004) 6.00.5 0 (0.2360.020 ) 0 FBA04900 3.50.2 (0.1380.008) 12.51.0 (0.4920.004) 9.00.5 (0.3540.020) 7.52.0 (0.2950.079) FBA03450 2.50.2 (0.0980.008) 15.01.0 (0.5910.004) 4.50.3 (0.1770.012) 7.02.0 (0.2760.079) 3.50.2 (0.1380.008) 15.01.0 (0.5910.004) 4.50.3 (0.1770.012) FBA04450 KD FBA04450 KE Standard quantity [pcs] Taped Bulk Ammo 1000 2000 1000 1000 2000 D 2.50.2 (0.0980.008) FBA03450 Radial lead (FBR) Dimensions Lead Symbol Type Axial lead (FBA) FBA04450 KF FBA04600 3.50.2 (0.1380.008) 15.01.0 (0.5910.004) 6.00.5 0 (0.2360.020 ) 0 FBA04900 3.50.2 (0.1380.008) 15.01.0 (0.5910.004) 9.00.53 (0.3540.020) 7.02.0 (0.2760.079) 0.650.05 (0.0260.020) 0.650.05 (0.0260.020) 0.650.05 (0.0260.020) 7.52.0 (0.2950.079) 7.52.0 (0.2950.079) 7.52.0 (0.2950.079) 7.52.0 (0.2950.079) 7.52.0 (0.2950.079) 7.52.0 (0.2950.079) Unit : mm (inch) Bulk dimensions VS Axial lead (FBA) NA Type D L1 Dimensions L2 FBA03450 2.50.2 (0.0980.008) FBA04450 3.50.2 4.50.3 6.5 max. (0.1380.008) (0.1770.012) (0.256 max.) FBA04600 3.50.2 (0.1380.008) 6.00.5 0 (0.2360.020 ) 0 8.5 max. (0.335 max.) FBA04900 3.50.2 9.00.5 (0.1380.008) (0.3540.020) 11.0 max. (0.433 max.) d 51 for 900 type only 4.50.3 6.5 max. (0.1770.012) (0.256 max.) Type 0.650.05 (0.0260.002) 18 min. (0.709 min.) Unit : mm (inch) US D Dimensions a A d F FBA03450 2.50.2 (0.0980.008) 4.50.3 12.5 max. 5.01.0 (0.1770.012) (0.492 max.) (0.1970.039) 0.650.05 (0.0260.002) FBA04450 3.50.2 4.50.3 12.5 max. 5.01.0 (0.1380.008) (0.1770.012) (0.492 max.) (0.1970.039) 0.650.05 (0.0260.002) 6.00.5 0 (0.2360.020 ) 0 FBA04600 3.50.2 (0.1380.008) 12.5 max. 5.01.0 (0.492 max.) (0.1970.039) 0.650.05 (0.0260.002) FBA04900 3.50.2 9.00.5 16.0 max. 5.01.0 (0.1380.008) (0.3540.020) (0.630 max.) (0.1970.039) 0.650.05 (0.0260.002) Unit : mm (inch) Radial lead (FBR) NA Type FBA03450 FBA04450 D 2.50.2 (0.0980.008) A Dimensions a 4.50.3 9.0 max. (0.1770.012) (0.354 max.) d F 5.01.0 (0.1970.039) 3.50.2 4.50.3 9.0 max. (0.1380.008) (0.1770.012) (0.354 max.) 0.650.05 (0.0260.002) Unit : mm (inch) KD/KE/KF Type D FBR05VA121 FBR06850 FBR06121 L1 Dimensions d W F 10.03 5.0 max. 9.0 max. 0.650.05 2.5 max. 2.51.0 5 (0.197 max.) (0.354 max.) (0.0260.002) (0.3940.118 (0.098 max.) (0.0980.039) 0.197 ) 10.03 6.00.5 7.0 max. 0.650.05 3.00.5 2.51.0 5 (0.2360.020) (0.276 max.) (0.0260.002) (0.3940.118 (0.1180.020) (0.0980.039) 0.197 ) 10.03 6.00.5 9.0 max. 0.650.05 3.00.5 2.51.0 5 (0.2360.020) (0.354 max.) (0.0260.002) (0.3940.118 (0.1180.020) (0.0980.039) 0.197 ) Unit : mm (inch) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. leaded_i04_pack-P1 12 leaded_i04_pack_e-01 PACKAGING NB SA (F : 2.5mm pitch) (0.098 inches) Type D Dimensions d L1 W F 5.01 5.01 0.60.05 2.5 max. 0.5 2 0.039 (0.0240.002) (0.1970.039 0.079 ) (0.098 max.) (0.1970.020 ) FBR07850 7.50.5 7.0 max. (0.2950.020) (0.276 max.) FBR07121 5.01 5.01 7.50.5 9.0 max. 0.60.05 2.5 max. 2 0.5 (0.2950.020) (0.354 max.) (0.0240.002) (0.1970.039 (0.098 max.) (0.1970.039 0.020 ) 0.079 ) Unit : mm (inch) Type Symbol Dimensions Symbol Dimensions 9.0 max. (0.354 max.) W 18.01.0 0.5 (0.7090.039 0.020 ) T 2.5 max. (0.098 max.) W0 12.5 min. (0.492 min.) D 5.0 max. (0.197 max.) W1 9.00.75 0.5 (0.3540.039 0.020 ) H 18.02.0 0 (0.7090.079 ) 0 W2 3.0 max. 2 (0.118 max.) P 12.71.0 (0.5000.039) 1.0 max. (0.039 max.) P0 12.70.3 1 (0.5000.039) D 0 4.00.3 (0.1570.012) P1 5.10.7 (0.2010.028) d 0.650.05 (0.0260.002) P2 6.351.3 (0.2500.051) L 11.0 max. (0.433 max.) F 2.51.0 0.5 (0.0980.039 0.020 ) t 0.70.2 (0.0280.008) h 0.02.0 (0.00.079) A Taping Dimensions AB (a : 26mm) (1.02inch lead space) FBR05 Type FBA03 Dimensions D 2.50.2 (0.0980.008) L a b |L1-L 2| d 1.5 0.8max 1.0 max 0.650.05 4.50.3 26.00 (0.1770.012) (1.020.059 ) (0.031max) (0.039 max) (0.0260.002) 0 Minimum insertion pitch 10.0 (0.394) 4.50.3 0.1770.012 FBA04 450 6.00.5 FBA04 3.50.2 0 26.01.5 0.8max 1.0 max 0.650.05 10.0 0 600 0.1380.0080.2360.020 0.031max0.039 max0.0260.0020.394 1.020.059 0 0 121: Unit : mm(inch) 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. 9.00.5 0.3540.020 FBA04 900 Unit : mm (inch) BB (a : 52mm) (2.05inches lead space) Type FBA03 FBA04 450 Dimensions D 2.50.2 (0.0980.008) L a b |L1-L 2| d 52.02 1.2 max 1.0 max 0.650.05 4.50.3 1 (0.1770.012) (2.050.079 0.039) (0.047 max) (0.039 max) (0.0260.002) Minimum insertion pitch 10.0 (0.394) 4.50.3 0.1770.012 6.00.5 FBA04 3.50.2 0 52.02 1.2max 1.0 max 0.650.05 10.0 1 600 0.1380.0080.2360.020 2.050.079 0.0390.047max0.039 max0.0260.0020.394 0 FBA04 900 9.00.5 0.3540.020 Unit : mm (inch) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. leaded_i04_pack_e-01 12 leaded_i04_pack-P2 PACKAGING SB/TB (F: 5mm pitch) (0.197 inches) Type Symbol Dimensions Symbol Dimensions A 4.50.3 (0.1770.012) h 0.02.0 (0.00.079) A1 9.0 max. (0.354 max.) W 18.01.0 0.5 (0.7090.039 0.020 ) 03: 2.7 max. (0.106 max.) W0 12.5 min. (0.492 min.) 04: 3.7 max. (0.146 max.) W1 9.00.75 0.5 (0.3540.039 0.020 ) H 20.00.5 1.0 (0.7870.020 0.039 ) W2 3.0 max. 2 (0.118 max.) P 12.71.0 (0.5000.039) 1.0 max. (0.039 max.) P0 12.70.3 1 (0.5000.012) D 0 4.00.3 (0.1570.012) D FBA03450 FBA04450 Type Symbol Dimensions P1 3.850.8 (0.1520.032) d 0.650.05 (0.0260.002) h 0.02.0 (0.00.079) P2 11.0 max. (0.433 max.) W 18.01.0 0.5 (0.7090.039 0.020 ) 6.351.3 (0.2500.051) L 7.0 max. (0.276 max.) F t 2.5 max. (0.098 max.) 0.70.2 (0.0280.008) W0 12.5 min. (0.492 min.) 5.01.0 (0.1970.039) 7.50.5 (0.9250.020) W1 9.00.75 0.5 (0.3540.039 0.020 ) SB: 18.02.0 0 (0.7090.079 ) 0 W2 3.0 max. 2 (0.118 max.) TB: 16.00.5 (0.6300.020) 1.0 max. (0.039 max.) P 12.71.0 (0.5000.039) D 0 4.00.3 (0.1570.012) P0 12.70.3 1 (0.5000.012) d 0.650.05 (0.020.002) P1 3.850.8 (0.1520.028) L 11.0 max. (0.433 max.) P2 6.351.3 (0.2500.051) t 0.70.2 (0.0280.008) F 5.01.0 0.5 (0.1970.039 0.020 ) Symbol A Dimensions 121: 9.0 max. (0.354 max.) 850: T D H FBR07 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. Unit : mm (inch) VB Unit : mm(inch) Type Symbol Dimensions Symbol Dimensions 450: 4.50.3 (0.1770.012) F 5.01.0 (0.1970.039) 600: 6.00.5 0 (0.2360.020 ) 0 h 0.02.0 (0.00.079) 900: 9.00.5 (0.3540.020) W 18.01.0 0.5 (0.7090.039 0.020 ) 450: 600: 12.5 max. (0.492 max.) W0 12.5 min. (0.492 min.) 900: 16.0 max. (0.630 max.) W1 9.00.75 0.5 (0.3540.039 0.020 ) D 3.7 max. (0.146 max.) W2 3.0 max. 2 (0.118 max.) H0 16.00.5 (0.6500.020) 1.0 max. (0.039 max.) P 12.71.0 (0.5000.039) D 0 4.00.3 (0.1570.012) P0 12.70.3 1 (0.5000.012) d 0.650.05 (0.0260.002) P1 3.850.8 (0.1520.032) L 11.0 max. (0.433 max.) P2 6.351.3 (0.2500.051) t 0.70.2 (0.0280.008) UB A A1 FBA03450 FBA04450 FBA04600 FBA04900 1 Accumulated error for 20 pitches is 2mm. 2 Bonding tape must not protrude from the base tape. Unit : mm (inch) This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. leaded_i04_pack-P3 12 leaded_i04_pack_e-01 RELIABILITY DATA 1. Operating temperature Range LA Type CAL45 Type 25105 LHL FBA/FBR 2585 FL05 Type 25105 FL06BT Type Test Method and Remarks LACAFL : Including self-generated heat LHL : Including self-generated heat 2. Storage temperature Range LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type 4085 3. Rated current LA Type CAL45 Type LHL Within the specified tolerance FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : The maximum DC value having inductance within 10% and temperature incease within 40 (LA:20) by the application of DC bias. LA, CA LHL : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25 (LHL08, LHL10, LHL13) : 30 (LHL16, LHLP) : 40 (LHLC08, LHLC10) FB : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within 20% of the initial value. This is not guaranteed for electrial characteristics during current application. FL : The maximum DC value having temperature rise within specified value. 4. Impedance LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Measuring equipment FB Measuring frequency FL06BT : Measuring equipment Measuring frequency Within the specified tolerance Refer to individual specification : : : : Impedance analyzer (HP4191A) or its equivalent Specified frequency 4291A (HP) or its equivalent Specified frequency 5. Inductance LA Type CAL45 Type Within the specified tolerance LHL FBA/FBR Within the specified tolerance FL05 Type FL06BT Type Test Method and Remarks : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent) LA, CA Measuring frequency : Specified frequency LHL : Measuring equipment : LCR meter (HP4285AHP42851A or its equivalent) LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency FL05R : Measuring equipment : HP4262A or its equivalent Measuring frequency : 1kHz 6. Q LA Type Within the specified tolerance CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA : Measuring equipment : LCR meter (HP4285A + HP42851A or its equivalent) Measuring frequency : Specified frequency LHL (except LHLP) : Measuring equipment : LCR meter (HP4285AHP42851A or its equivalent) LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli-RP1 12 le0104fi01_reli_e-01 RELIABILITY DATA 7. DC Resisitance LA Type CAL45 Type LHL Within the specified tolerance FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA, CA : Measuring equipment : low ohmmeter (A&D AD5812 or its equivalent) LHLFBFL : Measuring equipment : DC ohmmeter 8. Self resonance frequency LA Type Within the specified tolerance CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA : Measuring equipment : Network analyzer (Anritsu MS620J or its equivalent) LHL (except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent 9. Temperature characteristic LA Type L/L : Within 5% CAL45 Type L/L : Within 7% (except LHLP16 : Within 20%) LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA : Change of maximum inductance deviation in step 1 to 5 Step 1 2 3 4 5 Temperature () 20 25 (Minimum operating temperature) 20 (Standard temperature) 85 (Maximum operating temperature) 20 LHL : Change of maximum inductance deviation in step 1 to 5 Temperature at step 1 : 20 Temperature at step 2 : Minimum operating temperature Temperature at step 3 : 20 (Standard temperature) Temperature at step 4 : Maximum operating temperature Temperature at step 5 : 20 10. Tensile strength test LA Type CAL45 Type No abnormality such as cut lead, or looseness. LHL FBA/FBR No abnormality such as cut lead, or looseness. FL05 Type No abnormality such as cut lead, or looseness. FL06BT Type Test Method and Remarks : Apply the stated tensile force progressively in the direction to draw terminal. LA force (N) 25 CA duration (s) 5 : Apply the stated tensile force progressively in the direction to draw terminal. force (N) 10 duration (s) 10 LHL : Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter tensile d (mm) force (N) duration (s) 0.3d0.5 5 0.5d0.8 10 305 0.8d1.2 25 FBA/FBR : The body of a component shall be fixed and a tensile force of 201N shall be applied to the lead wire in the axial diretion of the component during 101 seconds. FL05R : Fix the body of a component in the direction to draw terminal,and gradually apply the tensile force of 4.9N. 11. Over current LA Type CAL45 Type LHL No emission of smoke no firing. There shall be no scorch or short of wire. LHLC08,LHLC10 : There shall be no firing. FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LHL/LACAL45 Type Measuring current Duration Number of measuring : Rated currentx2 : 5 min. : one time This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli_e-01 12 le0104fi01_reli-RP2 RELIABILITY DATA 12. Terminal strength : bending LA Type CAL45 Type No abnormality such as cut lead, or looseness. LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA, CA : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight d (mm) (N) (kg) 0.3d0.5 2.5 0.25 0.5d0.8 5 0.50 LHFB : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter tensile Bending force Mass reference weight d (mm) (N) (kg) 0.3d0.5 2.5 0.25 0.5d0.8 5 0.5 0.8d1.2 10 1.0 13. Insulation resisitance : between the terminals and body LA Type CAL45 Type 100M min. LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LHL : Applied voltage : 500 VDC Duration : 60 sec. 14. Insulation resistance : between terminals and core LA Type CAL45 Type LHL FBA/FBR 1M min. (Other than materail code MA) FL05 Type FL06BT Type Test Method and Remarks FBAFBR : Applied voltage : 100 VDC Duration : 605 sec. 15. Withstanding : between the terminals and body LA Type CAL45 Type No abnormality such as insulation damage LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LHL : Accoding to JIS C5102. 7. 1. 3 (C) Metal global method Applied voltage : 500 VDC Duration : 60 sec. 16. DC bias characteristic LA Type L/L : Within 10% CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks LA, CA : Measure inductance with appliation of rated current using LCR meter to compare it with the initial value. 17. Body strength LA Type No abnormality as damage. CAL45 Type LHL FBA/FBR No abnormality such as cracks on body. FL05 Type FL06BT Type Test Method and Remarks : Applied force : 30N LA Duration : 10 sec. Speed : Shall attain to specified force in 2 sec. CAL45 : Applied force : 50N Duration : 10 sec. Speed : Shall attain to specified force in 2 sec. FBA : Applied force : 503N Duration : 301 sec. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli-RP3 12 le0104fi01_reli_e-01 RELIABILITY DATA 18. Resisitance to vibration LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Directions LA, CA Frequency range Amplitude Mounting method Recovery : : : : : 2 hrs each in X, Y and Z directions total : 6hrs. 10 to 55 to 10Hz (1min.) 1.5mm Soldering onto printed board. At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. LHLFB Directions Frequency range Amplitude Mounting method : : : : 2 hrs each in X, Y and Z directions total : 6hrs. 10 to 55 to 10Hz (1min.) 1.5mm (But don't exceed acceleration 196m/s2 (two power)) Soldering onto printed board. L/L : Within 5% Q : 30min L/L : Within 5% L/L : Within 5% Q change : Within 30% (LHLP : only L/L) Appearance : No abnomality Impedance change : Within 20% Appearance : No abnomality 19. Resistance to shock LA Type No significant abnormality in appearance CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Drop test LA, CA Impact material : concrete or vinyl tile Height : 1m Total number of drops : 10 times 20. Solderability LA Type At least 75 of terminal electrode is covered by new solder. CAL45 Type LHL At least 75 of terminal electrode is covered by new solder. FBA/FBR At least 90 of terminal electrode is covered by new solder. FL05 Type At least 75 of terminal electrode is covered by new solder. FL06BT Type Test Method and Remarks : Solder temperature : 2305 LA, CA Duration : 20.5 sec. LHL : Solder temperature : 2355 : 20.5 sec. Duration Immersion depth : Up to 1.5mm from bottom of case. FB : Solder temperature : 2305 Duration : 31 sec. Immersion depth : Up to 1.5mm from terminal root. FL05R : Solder temperature : 2305 Duration : 20.5 sec. Immersion depth : Up to 2 to 2.5mm from terminal root. FL06BT : Solder temperature : 2305 Duration : 31 sec. Immersion depth : Up to 0.5 to 1.0mm from terminal root. 21. Resisitance to soldering heat LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Solder temperature LA, CA Duration Immersed conditions Recovery LHL : Solder bath method Manual soldering Caution Recovery FB : Solder bath method Recovery FL : Solder condition Immersion depth Recovery No significant abnormality in appearance L/L : Within 5% No significant abnormality in appearance No significant abnormality in appearance Refer to individual specification No significant abnormality in appearance : : : : Inductance change : Within 5% Impedance change : Within 20% Q change : Within 30%(LHLP : only L/L) Impedance change : Within 20% (CA) 2705, (LA) 2605 50.5 sec. One time Inserted into substrate with t=1.6mm At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. : Solder temperature : 2605 Duration : 101 sec. Up to 1.5mm from the bottom of case. : Solder temperature : 35010 (At the tip of soldering iron) Duration : 51 sec. Up to 1.5mm from the bottom of case. : No excessive pressing shall be applied to terminals. : 4 to 24hrs of recovery under the standard condition after the test. : Condition 1 : Solder temperature : 2605 Duration : 101 sec. Immersion depth : Up to 1.5mm from the terminal root. Condition 2 : Solder temperature : 3505 Duration : 31 sec. Immersion depth : Up to 1.5mm from the terminal root. : 3hrs of recovery under the standard condition after the test. 101 sec. : 2605 : Up to 0.5 to 1.0mm from the terminal root. : 3hrs of recovery under the standard condition after the test. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli_e-01 12 le0104fi01_reli-RP4 RELIABILITY DATA 22. Resisitance to solvent LA Type Please avoid the ultrasonic cleaning of this product. CAL45 Type LHL Impedance change : Within 20% FBA/FBR No significant abnormality in appearance FL05 Type FL06BT Type Test Method and Remarks FB : Solvent temperature : 2025 Duration : 305 sec. Solvent type : Acetone Recovery : 3hrs of recovery under the standard condition after the test. 23. Thermal shock LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Conditions for 1cycle LA, CA L/L : Within 10% Q : 30min L/L : Within 10% Appearance : No abnormality Appearance : No abnormality Refer to individual specification Appearance : No abnormality Step Temperature () 1 250 3 303 2 Room temperature Within 3 Inductance change : Within 10% Impedance change : Within 20% Q change : Within 30% (LHLPonly L/L) Impedance change : Within 20% Duration (min.) 3 852 0 303 4 Room temperature Within 3 Number of cycles : 5 cycles Recovery : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. LHLFB : Accoding to JIS C0025 Conditions for 1 cycle Step Temperature () 1 Minimum operating temperature0 3 2 Room temperature 3 Minimum operating temperature2 0 4 Room temperature Number of cycles : : Recovery : : FL Duration (min.) 303 Within 3 303 Within 3 10 cyclesLHL 5 cycles (FBA, FBR) 4 to 24hrs of recovery under the standard condition after the removal from the test chamber.LHL 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA, FBR) : Accoding to JIS C0025 Conditions for 1 cycle Step Temperature () 1 250 3 Duration (min.) 303 2 Room temperature Within 3 3 852 0 303 4 Room temperature Within 3 Number of cycles : 10 cycles Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 24. Damp heat LA Type L/L : Within 10% Q : 30min CAL45 Type L/L : Within 10% LHL Impedance changeWithin 20% FBA/FBR AppearanceNo abnormality FL05 Type FL06BT Type Test Method and Remarks LA, CA : Temperature : 402 Humidity : 9095%RH Duration : 1000 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. FB : Temperature Humidity Duration Recovery : : : : 602 9095%RH 1000 hrs 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli-RP5 12 le0104fi01_reli_e-01 RELIABILITY DATA 25. Loading under damp heat LA Type CAL45 Type LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Temperature LA, CA : Humidity : Duration : Applied current : Recovery : L/L : Within 10% Q : 30min L/L : Within 10% Appearance : No abnormality Imductance change : Within 10% Refer to individual specification Appearance : No abnormality Impedance change : Within 20% Q change : Within 30% (LHLP : only L/L) 402 9095%RH 1000 hrs Rated current At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. LHL : Temperature Humidity Duration Applied current Recovery : : : : : 402 9095%RH 100024 hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. FL : : : : : 603 9095%RH 500 (12, 0) hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. : Temperature Humidity Duration Applied current Recovery 26. Loading at high temperature LA Type L/L : Within 10% Q : 30min CAL45 Type L/L : Within 10% LHL FBA/FBR FL05 Type FL06BT Type Test Method and Remarks : Temperature LA, CA : 852 Duration : 1000 hrs Applied current : Rated current Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test LA Type L/L : Within 10% Q : 30min CAL45 Type L/L : Within 10% Inductance change : Within 10% Q change : Within 30% (LHLP : only L/L) LHL Appearance : No abnormality FBA/FBR Refer to individual specification FL05 Type Impedance change : Within 20% FL06BT Type Appearance : No abnormality Test Method and Remarks : Temperature : 252 LA, CA Duration : 1000 hrs Recovery : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. LHL : Temperature : 403 Duration : 100024 hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. FL : Temperature : 403 Duration : 500 (12, 0) hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 28. High temperature life test LA Type CAL45 Type Inductance change : Within 10% Q change : Within 30% (LHLP : only L/L) Appearance : No abnormality LHL FBA/FBR Refer to individual specification FL05 Type Impedance change : Within 20% FL06BT Type Appearance : No abnormality Test Method and Remarks LHL : Temperature : 1053 Duration : 100024 hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. FL : Temperature : 853 Duration : 500 (12, 0) hrs Recovery : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli_e-01 12 le0104fi01_reli-RP6 PRECAUTIONS CAL Type, LH Type, FB Type, FL Type, LA Type 1. Circuit Design Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high Precautions reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. Technical Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of considerations the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. Precautions 3. Considerations for automatic placement Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. Precautions 2. Mounting and soldering conditions should be checked beforehand. Technical Adjustment of mounting machine consider1. When installing products, care should be taken not to apply distortion stress as it may deform the products. ations 4. Soldering Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. Recommended conditions for using a soldering iron: Precautions Put the soldering iron on the land-pattern. Soldering iron's temperature - Below 350 Duration - 3 seconds or less The soldering iron should not directly touch the inductor. Reflow soldering 1. As for reflow soldering, please contact our sales staff. Technical Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of considerations the products. 5. Cleaning Precautions Technical considerations Cleaning conditions 1. CAL type, LH type, LA Type Please do not do cleaning by a supersonic wave. Cleaning conditions 1. CAL type, LH type, LA Type If washing by supersonic waves, supersonic waves may deform products. 6. Handling Handling 1. Keep the inductors away from all magnets and magnetic objects. Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type Precautions If inductors are dropped onto the floor or a hard surface they should not be used. Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). Handling 1. There is a case that a characteristic varies with magnetic influence. Mechanical considerations Technical 1. There is a case to be damaged by a mechanical shock. consider2. LH type ations There is a case to be broken by a fall. Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions Ambient temperature 040 Precautions Humidity Below 70% RH The ambient temperature must be kept below 30. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of considerations taping/packaging materials may take place. This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs. le0104fi01_reli-RP7 12 le0104fi01_reli_e-01