ALUMINUM ELECTROLYTIC CAPACITORS
Extremely Low Impedance, High Reliability
High reliability withstanding 5000 hour load life at +105
°C
(3000/2000 hours
for smaller case sizes as specified below).
Capacitance ranges available based on the numerical values in E12 series
under JIS.
Compliant to the RoHS directive (2002/95/EC).
Radial Lead Type Type numbering system (Example : 25V 470
µ
F)
Frequency coefficient of
rated ripple current
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 4 for the minimum order quantity.
PMseries
(through 100V only)
PM
PW
Smaller
Dimension table in next page.
Specifications
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
Tangent of loss angle (tan δ)
Stability at Low Temperature
Endurance
Marking
Performance CharacteristicsItem –55 to +105°C (6.3 to 100V), –40 to +105°C (160 to 400V), –25 to +105°C (450V)
6.3 to 450V
0.47 to 15000µF
±20% at 120Hz, 20°C
Rated Voltage (V)
Leakage current
For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. Measurement frequency : 120Hz, Temperature : 20°C
120Hz
After 1 minute's application of rated voltage, leakage current is not more
than 0.03CV or 4 (µA), whichever is greater.
Printed with white color letter on dark brown sleeve.
The specifications listed at right shall be met when the
capacitors are restored to 20°C after D.C. bias plus rated
ripple current is applied for 5000 hours (2000 hours for φD=5
and 6.3, 3000 hours for φD=8) at 105°C, the peak voltage
shall not exceed the rated voltage.
Shelf Life
After storing the capacitors under no load at 105°C
for 1000 hours and then performing voltage treatment based
on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the
characteristic requirements listed at right.
160 to 450
CV <
=1000 :
I
= 0.1CV+40 (µA) max. (1 minute's)
CV > 1000 :
I
= 0.04CV+100 (µA) max. (1 minute's)
Rated voltage (V)
Impedance
ratio (MAX.)
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Z–55°C / Z+20°C
Rated Voltage (V)
tan δ (MAX.)
6.3
0.22
6.3 · 10
—
—
4
16
—
—
3
25 · 35
—
—
3
50 to 100
—
—
2
160
·
200
—
4
—
250
—
6
—
315
·
350
—
8
—
400
—
10
—
450
15
—
—
10
0.19 16
0.16 25
0.14 35
0.12 50
0.10 63 to 100
0.08 160 to 350
0.20 400 · 450
0.25
6.3 to 100
Leakage current
tan δ
Capacitance change
Less than or equal to the initial specified value
200% or less than the initial specified value
Within ±20% of the initial capacitance value
Leakage current
tan δ
Capacitance change
Less than or equal to the initial specified value
150% or less than the initial specified value
Within ±20% of the initial capacitance value
• Please refer to page 20 about the end seal configulation.