SPEC NO: DSAD1260 REV NO: V.3 DATE: DEC/21/2005 PAGE: 1 OF 5
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: Y.W.WANG ERP: 1202000642
Package Dimensions
P/N: AM2520SGD03 SUPER BRIGHT GREEN
Description
The Super Bright Green source color devices are made
with Gallium Phosphide Green Light Emitting Diode.
Features
SUBMINIA TURE PACKAGE.
WIDE VIEWING ANGLE.
GULL WING LEAD.
LONG LIFE - SOLID STATE RELIABILITY.
LOW PACKAGE PROFILE.
PACKAGE : 1000PCS / REEL.
RoHS COMPLIANT.
SUBMINIATURE SOLID STATE LAMP
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. Specifications are subject to change without notice.
SPEC NO: DSAD1260 REV NO: V.3 DATE: DEC/21/2005 PAGE: 2 OF 5
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: Y.W.WANG ERP: 1202000642
Selection Guide
Note:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 the optical centerline value.
Electrical / Optical Characteristics at TA=25°C
Absolute Maximum Ratings at TA=25°C
Note:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
Symbol Parameter Device Typ. Max. Test ConditionsUnits
λpeak Peak Wavelength Super Bright Green 565 nm IF=20mA
λDDominant Wavelength Super Bright Green 568 nm IF=20mA
∆λ1/2 Spectral Line Half-width Super Bright Green 30 nm IF=20mA
C Capacitance Super Bright Green 15 pF VF=0V;f=1MHz
VFForward Voltage Super Bright Green 2.2 2.5 V IF=20mA
IRReverse Current Super Bright Green 10 uA VR = 5V
Parameter Super Bright Green Units
Power dissipation 105 mW
DC Forward Current 25 mA
Peak Forward Current [1] 140 mA
Reverse Voltage 5 V
Operating / Storage Temperature -40°C To +85°C
Part No. Dice Lens Type Iv (mcd)
@ 20mA
Viewing
Angle
Min. Typ. 2 θ
θ θ
θ 1/2
AM2520SGD03 40°SUPER BRIGHT GREEN (GaP) GREEN DIFFUSED 2.6 10
SPEC NO: DSAD1260 REV NO: V.3 DATE: DEC/21/2005 PAGE: 3 OF 5
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: Y.W.WANG ERP: 1202000642
Super Bright Green AM2520SGD03
SPEC NO: DSAD1260 REV NO: V.3 DATE: DEC/21/2005 PAGE: 4 OF 5
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: Y.W.WANG ERP: 1202000642
AM2520SGD03
Tape Specifications
(Units : mm)
Recommended Soldering Pattern
(Units : mm)
SPEC NO: DSAD1260 REV NO: V.3 DATE: DEC/21/2005 PAGE: 5 OF 5
APPROVED: J. Lu CHECKED: Allen Liu DRAWN: Y.W.WANG ERP: 1202000642
Remarks:
If special sorting is required (e.g. binning based on forward voltage, luminous intensity/ luminous flux or wavelength),
the typical accuracy of the sorting process is as follows:
1. Wavelength: +/-1nm
2. Luminous Intensity/ Luminous Flux: +/-15%
3. Forward Voltage: +/-0.1V
Note: Accuracy may depend on the sorting parameters
PACKING & LABEL SPECIFICATIONS AM2520SGD03