6ES7134-0HF01-0XB0 - SIEMENS

Product Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Product Information for the ET 200B Distributed

I/O System

This

Product Information refers to the

ET 200B Distributed I/O Device

manual, edition 04 (order no.: 6ES5 998-4ET

.1).

General Information on the ET 200B

The

supply voltage on the PROFIBUS-DP port is intended for connecting a

bus connector

, an ET

200 hand-held device (only in the case of digital mod

ules) or an OLP

The display of the “DIA” diagnostic LED has the following additional signif

icance for the analog modules of the ET

200B:

If you set ”disable” for the ”Diagnostics Alarm” parameter and ”enable” for

the ”Diagnostics Enable CH0” parameter (for channel/channel group) during

parameterization, when there is an error on the corresponding channel the

“DIA” LED comes on, although disabling the diagnostics alarm prevents a

diagnosis from being reported to the CPU.

The type U compensation unit described on page 8-9 in table 8-3 together

with its accessories is no longer supplied.

Note on table 8-25 on page 8-39:

Hinweis

The possible resolutions in table 8-25 do not apply to temperature values.

The converted temperature values are the result of a conversion in the analog

module.

Third rule (third point):



The terminals of unused outputs are left open when voltage output

measurement) is configured.



The terminals of unused outputs must be shorted whencurrent output

(I measurement) is configured.

Applicability

Section

3.6,

Pg. 3-28: W

iring

the Bus

Connection

Section 5.2,

Pg. 5-4: Error

Display Analog

ET 200B

Section 8.4.1,

Table

8-3: Com

pensation Units

Section 8.4.5,

Pg. 8-39:

Resolution

Section 8.6.1,

Pg. 8-78: Rules

2Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

the event of a wire break, the ET

200B-4AI analog module up to and in

cluding release 2 may report a measurement range underflow instead of a

wire break. As of release 3, the following values apply in tables 8-50 and

8-54 in the

ET 200B Distributed I/O Device

manual:

Tabelle 8-50 Representation of Digitized Measured Values of the ET 200B-4AI

(6ES7 134-0HF01-0XB0; Measurement Range: 4 to 20 mA)

Units Measured

value

Digitized Measured Value1X X O Range

4 ... 20 mA 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

2559 19.992 0 1 0 0 1 1 1 1 1 1 1 1 1 0 0 1

2048 16.000 0 100000000000000

512 4.000 0 001000000000000 Rated

511 3.992 0 000111111111000 range

384 3.000 0 000110000000000

383 2.992 0 000101111111000

151 1.185 0 000010010111000

4095 < 1.185 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 Wire break

1Same

representation in data format twos complement, value and sign and binary repre

sentation

Tabelle 8-54 Representation of Digitized Measured Values of the ET 200B-4AI

(Measurement Range: 0 to 20 mA and 4 to 20 mA)

Measure-

ment Range

Measure-

ment Range

Units

men

ange

from 0

to 20 mA

men

ange

from 4

to 20 mA Decimal Hexadeci-

mal Range

 23.5185  22.815 32767 7FFFHOverflow

23.518 22.814 32511 7EFFH

: : : : Overrange

20.0007 20.0006 27649 6C01H

20.000 20.000 27648 6C00H

15.000 16.000 20736 5100H

Rated range

: : : : Rated range

0.000 4.000 0 0H

-0.0007 3.9995 –1 FFFFH

: : : : Underrange

–3.5185 1.1852 –4864 ED00H

–3.5192 –32768 8000HUnderflow

1.1846 –32768 8000HWire break

Section

5.3.8,

Pg. 5-21:

Measurement

Range Underflow

Table 8-50,

Pg. 8-69

Table 8-54,

Pg. 8-71

Product Information ET 200B

Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

table 8-58 on page 8-84 it is also possible to specify that the channel is not

activated for output value and range.

Note on table A-2 on page A-3:

Hinweis

The SIxxxAD.200 and SIxxxTD.200 type files contain the normal identifier

format for configuration (see table D-7). The SIxxxBD.200 type files contain

the special identifier format (see table B-4).

If, while running an analog ET

200B module, reconfiguration is carried out

with another type file version (e.g. previously with SIxxxAD.200 and subse

quently with SIxxxBD.200, or vice versa), you must carry out a ST

OP-RUN

transition on the analog module.

The following applies to ET

200B analog modules as of release 3:

o permit analog ET

200B modules to be connected to DP masters of other

manufacturers, all analog ET

200B modules as of release 3 also support the

normal identifier format.

The prerequisite for this is that your non-Siemens master must send a control

command (”UNCLEAR”) cyclically and be able to process diagnostic frames

up to 29 bytes in length. If your non-Siemens master does not fulfill these

requirements, you can only run the ET

200B modules by means of a device

master file created using COM PROFIBUS on the basis of the SIxxxAD.200

type files.

For non-Siemens masters, COM PROFIBUS allows you as of version V3.1 to

create a device master file for every analog ET

200B module with address

identifiers in the normal identifier format.

The type files for COM PROFIBUS and STEP 7 still contain the preset ad

dress identifiers in the special identifier format for these analog modules.

As of release 3, a DP master can read the normal identifier format from the

analog ET

200B modules after each power on as in table D-7 (

ET 200B Dis

tributed I/O Device

manual). If the special identifier format is used in config

uration, the module makes the special identifier format available.

As long as the DP master is in CLEAR mode, the diagnostic information of

the ET

200B modules is

not

updated.

Section

8.6.3,

Pg. 8-84:

Parameters

Section A.1,

Pg.

A-3:

Analog Modules

Section B, Pg. B-1:

Normal ID format

Updating of the

Slave Diagnostics

Product Information ET 200B

4Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Product Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Product Information for the

TB3-4/DC, 6ES7 193-0CA40-0XA0, as of version

Fig.

Fig. II

6Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Fig.

III

200B-16DO

TB3-4/DC

X1 L3+ M

5 V

Q1:

0...7

L2+L1+

Q0: 0...7

PROFIBUS-DP

L2+L1+ L3+ M

Fig.

Logic

Interface

between electronics block and terminal block

Station

number

selection

Suppr

. Logic

STOP/RUN-

switch

PROFIBUS-DP

connection

Screw for groun-

ded

configuration

Digital

outputs

24 V

supply

Outp.

Ground

Supply

Product

Information for the TB3-4/DC

Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Description The

TB3-4/DC terminal block belongs to the family of the ET 200B distribu

ted I/O station modules.

Fig. I:

Basic construction: TB3-4/DC terminal block (spring-release termi

nal)

Polarization slide

Switch for setting the station number (this number is not accepted by

the system until you actuate the ST

OP/RUN switch (ST



RUN))

PROFIBUS-DP interface

Screw for connecting frame to PE

M5 screw for connecting PE

erminal block for inputs/outputs

Slide for removing the terminal block from the standard mounting rail

erminals for the logic supply and the load power supply

9ST

OP/RUN switch for switching the power supply to the logic compo

nents in the electronics block on and of

f. The ST

OP/RUN switch also

switches the ET

200B distributed I/O station on and of

10 Fuse

Fig. II: Dimension drawing: TB3-4/DC terminal block

Fig. III:

erminal designations: TB3-4/DC terminal block

Fig. IV

Block diagram: TB3-4/DC terminal block and ET

200B-16DO

The TB3-4/DC terminal block (spring-release terminal, 4-tier) of

fers the

same functionality as the TB1-4/DC terminal block (screw terminal, 4-tier).

The only dif

ference is that the TB3-4/DC is fitted with a 4-tier

spring-re-

lease

terminal.

The ET

200B-16DI, -16DO, -8DI/8DO, -8DI/8DO HW

A and -8RO electro

nics blocks can all be connected to the TB3-4/DC terminal block.

ou can find details of how to install and set the terminal blocks of the

200B in the

ET 200B Distributed I/O Station

manual.

The assignment of the inputs and outputs on the terminal blocks of the

TB3-4/DC depends on the type of electronics block mounted on them.

The pin-out of all the plug-in electronics blocks for the TB1-4/DC is descri

bed in the

ET 200B Distributed I/O Station

manual. This pin-out is the same

as for the TB3-4/DC.

Characteristics

Installation and

settings

Input/output

connections

Product Information for the TB3-4/D

8Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Product Information for the

TB4-4/DC, 6ES7 193-0CB40-0XA0, as of version

Fig.

Fig. II

Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Fig.

III

200B-16DO/2A

TB4-4/DC

L5+ M5L1+ Q0:

0...3 L2+ M2M1 Q0:

4...7 L3+ M3 Q1:

0...3 L4+ M4

4x 4x 4x 4x

L5+ M5

5 V

Q1:

4...7

L1+M1 L2+M2 L3+M3 L4+M4

PROFIBUS-DP

Fig.

Station

number

selection

PROFIBUS-DP

Connection

Screw for groun-

ded

configuration

Logic

Interface between electronics block and terminal block

Outp.

Supply

Ground

Digital

outputs

Suppr

. Logic

STOP/RUN-

switch

24 V

supply

Suppr.

logic Suppr.

logic

Product

Information for the TB4-4/D

10 Product

Information on the ET 200B Distributed I/O Station

A 4NEB 780 6731-02

Description The

TB4-4/DC terminal block belongs to the family of the ET 200B distribu

ted I/O station modules.

Fig. I:

Basic construction: TB4-4/DC terminal block (spring-release termi

nal)

Polarization slide

Switch for setting the station number (this number is not accepted by

the system until you actuate the ST

OP/RUN switch (ST



RUN))

PROFIBUS-DP interface

Screw for connecting frame to PE

M5 screw for connecting PE

erminal block for inputs/outputs and the load power supply

Slide for removing the terminal block from the standard mounting rail

erminals for the logic supply

9ST

OP/RUN switch for switching the power supply to the logic compo

nents in the electronics block on and of

f. The ST

OP/RUN switch also

switches the ET

200B distributed I/O station on and of

10 Fuse

Fig. II: Dimension drawing: TB4-4/DC terminal block

Fig. III:

erminal designations: TB4-4/DC terminal block

Fig. IV

Block diagram: TB4-4/DC terminal block and ET

200B-16DO/2A

The TB4-4/DC terminal block (spring-release terminal, 4-tier) of

fers the

same functionality as the TB2-4/DC terminal block (screw terminal, 4-tier).

The only dif

ference is that the TB4-4/DC is fitted with a 4-tier

spring-re-

lease

terminal.

The ET

200B-16DO/2A, -32DI, -32DI 0.2ms, -32DO, -16DI/16DO,

-24DI/8DO and -24DI/8DO 0.2ms electronics blocks can all be connected to

the TB4-4/DC terminal block.

ou can find details of how to install and set the terminal blocks of the

200B in the

ET 200B Distributed I/O Station

manual.

The assignment of the inputs and outputs on the terminal blocks of the

TB4-4/DC depends on the type of electronics block mounted on them.

The pin-out of all the plug-in electronics blocks for the TB2-4/DC is descri

bed in the

ET 200B Distributed I/O Station

manual. This pin-out is the same

as for the TB4-4/DC.

Characteristics

Installation and

settings

Input/output

connections

Product Information for the TB4-4/D