HD-LINX TM GS1522 HDTV Serial Digital Serializer DATA SHEET DESCRIPTION * SMPTE 292M compliant The GS1522 is a monolithic bipolar integrated circuit designed to serialize SMPTE 274M and SMPTE 260M bit parallel digital signals. * 20:1 parallel to serial conversion * NRZ(I) encoder & SMPTE scrambler with selectable bypass This device performs the following functions: * NRZ to NRZ(I) serial data conversion * Sync word mapping for 8-bit/10-bit operation. * Parallel to Serial conversion of Luma & Chroma data * Interleaving of Luma and Chroma data * 9 4 Data Scrambling (using the X +X +1 algorithm) * Conversion of NRZ to NRZI serial data (using the (X+1) algorithm) * Selectable DUAL or QUAD 75 Cable Driver outputs * Lock Detect Output * 1.485Gb/s or 1.485/1.001Gb/s operation * 1.485Gb/s and 1.485/1.001Gb/s operation * lock detect output * selectable DUAL or QUAD 75 cable driver outputs * 8 bit or 10 bit input data support * 20 bit wide inputs * Pb-free and Green * 3.3V and 5V CMOS/TTL compatible inputs * single +5.0V power supply APPLICATIONS SMPTE 292M Serial Digital Interfaces for Video Cameras, Camcorders, VTRs, Signal Generators, Portable Equipment, and NLEs. This device requires a single 5V supply and typically consumes less than 1000mW of power while driving two 75 cables. The GS1522 uses the GO1515 external VCO connected to the internal PLL circuitry to achieve ultra low noise PLL performance. ORDERING INFORMATION PART NUMBER PACKAGE TEMPERATURE Pb-FREE AND GREEN GS1522-CQR 128 pin MQFP 0C to 70C No GS1522-CQRE3 128 pin MQFP 0C to 70C Yes RSET0 RESET BYPASS SYNC_DETECT _DISABLE 20 DATA_IN[19:0] 20 SYNC DETECT SDO0 SMPTE INPUT LATCH SCRAMBLER O/P0 RESET INTERLEAVER BYPASS PCLK_IN SDO0 PARALLEL TO SERIAL CONVERTER SCLK PLL SDO1 O/P1 NRZ TO NRZI SDO1 PLOAD MUTE GO1515 RSET1 SDO1_EN PLL_LOCK FUNCTIONAL BLOCK DIAGRAM Revision Date: June 2004 Document No. 522 - 26 - 03 GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: info@gennum.com www.gennum.com GS1522 FEATURES ABSOLUTE MAXIMUM RATINGS PARAMETER VALUE Supply Voltage (VS) 5.5V Input Voltage Range (any input) VEE - 0.5 < VIN < VCC+ 0.5 TBD Power Dissipation (VCC = 5.25V) TBD Input ESD Voltage TBD Die Temperature GS1522 DC Input Current (any input) 125C 0C TA 70C Operating Temperature Range -40C TS 150C Storage Temperature Range Lead Temperature (soldering 10 seconds) 260C AC ELECTRICAL CHARACTERISTICS VCC = 5V, VEE = 0V, TA = 0C to 70C unless otherwise specified. PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS BRSDO - 1.485 - Gb/s Serial data bit rate SMPTE 292M Digital Serial Data Outputs Differential outputs VSDO 750 800 850 mV p-p Rise/Fall times, 20-80% tr, tf - 150 270 ps - 0 7 % 15 17 - dB Overshoot Output Return Loss @ 1.485GHz ORL Lock Time Worst case tLOCK Typical Loop Bandwidth 0.1dB peaking, 1.485Gb/s Intrinsic Jitter Pseudo-random NOTES 1.485/1.001Gb/s also With 52.3 1% RSET Resistor As per SMPTE292M (5MHz to clock frequency), using Gennum Evaluation Board, recommended layout and components. - 200 250 ms - 0.200 1.5 MHz tIJR - - 100 ps p-p tIJP - - 100 ps p-p tIJR - - 100 ps p-p tIJP - - 100 ps p-p 23 PRBS (2 -1) (200kHz LBW) Pathological 23 PRBS (2 -1) (200kHz LBW) Pseudo-random (1.5 MHz LBW) Pathological (1.5 MHz LBW) 2 of 20 GENNUM CORPORATION 522 - 26 - 03 AC ELECTRICAL CHARACTERISTICS - PARALLEL TO SERIAL STAGE VDD = 5V, TA = 0C to 70C unless otherwise specified. PARAMETER CONDITIONS MIN TYP MAX UNITS VIL - - 0.8 V For compatibility with TTL voltage levels VIH 2.0 - - V For compatibility with TTL voltage levels Input Capacitance CIN - 1 2 pF Output Voltage Levels VOL - - 0.4 V For compatibility with TTL voltage levels VOH 2.4 - - V For compatibility with TTL voltage levels PCLK_IN - 74.25 - MHz Input Clock Pulse Width LOW tPWL 5 - - ns Input Clock Pulse Width HIGH tPWH 5 - - ns Input Clock Rise/Fall time tr, tf - 500 1000 ps Input Clock Rise/Fall time Matching trfm - 200 - ps Input Setup Time tSU 1.0 - - ns Input Hold Time tIH 0 - - ns Input Voltage Levels Parallel Input Clock Frequency NOTES 74.25/1.001MHz also 20% to 80% DC ELECTRICAL CHARACTERISTICS VCC = 5V, VEE = 0V, TA = 0C to 70C unless otherwise specified. PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS NOTES Positive Supply Voltage Operating Range VCC 4.75 5.00 5.25 V Power (system power) VCC = 5.00V, T=25C PD - 950 - mW (Driving two 75 outputs) VCC = 5.00V, T=25C PD - 1170 - mW (Driving four 75 outputs) VCC = 5.25V, T=70C - - 300 mA (Driving four 75 outputs) VCC = 5.00V, T=25C - 234 - mA (Driving four 75 outputs) SDO1 disabled - - 240 mA (Driving two 75 outputs) - 190 - mA (Driving two 75 outputs) Supply Current VCC = 5.25V, 70C SDO1 disabled VCC = 5.0V, 25C 3 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 SYMBOL 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 OSC_VEE A0 NC NC NC VEE2 RSET0 VCC2 NC SDO0 SDO_NC SDO0 NC NC NC SDO1 SDO_NC SDO1 NC VCC2 RSET1 NC NC NC NC NC PIN CONNECTIONS GS1522 NC 65 38 NC NC 66 37 NC NC 67 36 NC NC 68 35 NC NC 69 34 NC NC 70 33 NC NC 71 32 NC NC 72 31 SDO1_EN NC 73 30 VEE2 VCO 74 29 VEE2 VCO 75 28 VEE2 PD_VEE 76 27 VEE2 PDSUB_VEE 77 26 VEE2 IJI 78 25 VCC2 PD_VCC 79 24 VCC2 NC 80 23 VCC2 NC 81 22 VCC2 LFS 82 21 VCC2 NC 83 20 NC LFS 84 19 NC PLCAP 85 18 VEE2 DM 86 17 RESET PLCAP 87 16 BYPASS DFT_VEE 88 15 PLL_LOCK LFA_VEE 89 14 NC LFA 90 13 XDIV20 LBCONT 91 12 NC LFA_VCC 92 11 NC NC 93 10 BUF_VEE VCC3 94 9 NC VEE3 95 8 NC SYNC_DETECT_DISABLE 96 7 NC NC 97 6 NC NC 98 5 NC NC 99 4 NC NC 100 3 NC NC 101 2 PCLK_IN NC 102 1 VEE3 DATA_IN[19] DATA_IN[18] DATA_IN[17] DATA_IN[16] DATA_IN[15] NC NC DATA_IN[14] DATA_IN[13] DATA_IN[12] DATA_IN[11] DATA_IN[10] DATA_IN[9] NC NC DATA_IN[8] DATA_IN[7] NC NC DATA_IN[6] DATA_IN[5] DATA_IN[4] DATA_IN[3] DATA_IN[2] DATA_IN[1] DATA_IN[0] 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 GS1522 TOP VIEW NOTE: No Heat Sink Required 4 of 20 GENNUM CORPORATION 522 - 26 - 03 PIN DESCRIPTIONS NUMBER 1, 95 2 LEVEL TYPE DESCRIPTION VEE3 Power Input Negative Supply. Most negative power supply connection, for input stage. PCLK_IN TTL Input Parallel Data Clock. 74.25 or 74.25/1.001MHz NC No Connect. These pins are not used internally. These pins should be floating. 10 BUF_VEE Power TEST Negative Supply/Test Pin. Most negative power supply connection. For buffer for oscillator/divider for test purposes only. Leave floating for normal operation. 13 XDIV20 TTL TEST Test Pin. Test block output. Leave floating for normal operation. 15 PLL_LOCK TTL Output Status Signal Output. Indicates when the GS1522 is phase locked to the incoming PCLK_IN clock signal. LOGIC HIGH indicates PLL is in Lock. LOGIC LOW indicates PLL is out of Lock. 16 BYPASS TTL Input Control Signal Input. Used to bypass the scrambling function if data is already scrambled by GS1501 or if non-SMPTE encoded data stream such as 8b/10b is to be transmitted. When BYPASS is LOW, the SMPTE scrambler and NRZ(I) encoder are enabled. When BYPASS is HIGH, the SMPTE scrambler and NRZ(I) encoder are bypassed. 17 RESET TTL Input Control Signal Input. Used to reset the SMPTE scrambler. For logic HIGH; Resets the SMPTE scrambler and NRZ(I) encoder. For logic LOW: normal SMPTE scrambler and NRZ(I) encoder operation. 18, 26, 27, 28, 29, 30, 59 VEE2 Power Input Negative Supply. Most negative power supply connection. For Cable Driver outputs and all other digital circuitry excluding input stage and PLL stage. 21, 22, 23, 24, 25, 45, 57 VCC2 Power Input Positive Supply. Most positive power supply connection. For Cable Driver outputs and all other digital circuitry excluding input stage and PLL stage. 31 SDO1_EN Power Input Control Signal Input. Used to enable or disable the second serial data output stage. This signal must be tied to GND to enable this stage. Do not connect to a logic LOW. 44 RSET1 Input Control Signal Input. External resistor is used to set the data output amplitude for SDO1 and SDO1. Use a 1% resistor. 47, 49 SDO1, SDO1 Analog Output Serial Data Output Signal. Current mode serial data output #1. Use 75 1% pull up resistors to VCC2. 48, 54 SDO_NC 53, 55 SDO0, SDO0 Analog Output Serial Data Output Signal. Current mode serial data output #0. Use 75 1% pull up resistors to VCC2. RSET0 Analog Input Control Signal Input. External resistor is used to set the data output amplitude for SDO0 and SDO0. Use a 1% resistor. 58 No Connect. Not used internally. This pin must be left floating. 5 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 3, 4, 5, 6, 7, 8, 9, 11, 12, 14, 19, 20, 32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43,46, 50, 51, 52, 56, 60, 61, 62, 65, 66, 67, 68, 69, 70, 71, 72, 73, 80, 81, 83, 93, 97, 98, 99, 100, 101, 102, 108, 109, 116, 117, 120, 121 SYMBOL PIN DESCRIPTIONS (Continued) NUMBER LEVEL TYPE DESCRIPTION 63 A0 TTL TEST Test Signal. Used for manufacturing test purposes only. This pin must be tied low for normal operation. 64 OSC_VEE Power Input Negative Supply. Ground for ring oscillator. This pin must be floating for normal operation. 74 VCO Analog Input Control Signal Input. Input pin is AC coupled to ground using a 50 transmission line. 75 VCO Analog Input Control Signal Input. Voltage controlled oscillator input. This pin is connected to the output pin of the GO1515 VCO. This pin must be connected to the GO1515 VCO output pin via a 50 transmission line. 76 PD_VEE Power Input Negative Supply. Most negative power supply connection. For phase detector stage. 77 PDSUB_VEE Power Input Guard Ring. Ground guard ring connection to isolate phase detector in PLL stage. 78 IJI Analog Output 79 PD_VCC Power Input Positive Supply. Most positive power supply connection. For phase detector stage. 82, 84 LFS, LFS Analog Input Loop Filter Connections. 85, 87 PLCAP, PLCAP Analog Input Control Signal Input. Phase lock detect time constant capacitor. Status Signal Output. Indicates the amount of excessive jitter on the incoming SDI and SDI input. 86 DM 88 DFT_VEE Power Input Most Negative Power Supply Connection . Enables the jitter demodulator functionality. This pin should be connected to ground. If left floating, the DM function is disabled resulting in a current saving of 340A. 89 LFA_VEE Power Input Negative Supply. Most negative power supply connection. For loop filter stage. 90 LFA Analog Output 91 LBCONT Analog Input Control Signal Input. Used to provide electronic control of Loop Bandwidth. 92 LFA_VCC Power Input Positive Supply. Most positive power supply connection. For loop filter stage. 94 VCC3 Power Input Positive Supply. Most positive power supply connection. For input stage. 96 SYNC_DETECT_DISABLE TTL Input Control Signal Input. Used to disable the sync detection function. Logic HIGH disables sync detection. Logic LOW: 000-003 is mapped into 000 and 3FC-3FF is mapped into 3FF for 8-bit operation. DATA_IN[19:0] TTL Input Input Data Bus. The device receives a 20 bits data stream running at 74.25 or 74.25/1.001 MHz from the GS1501 HDTV Formatter or GS1511 HDTV Formatter. Input data can be in SMPTE292M scrambled or unscrambled format. DATA_IN[19] is the MSB (pin 103). DATA_IN[0] is the LSB (pin 128). 103, 104, 105, 106, 107, 110, 111, 112, 113, 114, 115, 118, 119, 122, 123, 124, 125, 126, 127, 128 Test Signal. Used for manufacturing test only. This pin must be left floating in normal operation. Control Signal Output. Control voltage for GO1515 VCO. 6 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 SYMBOL INPUT/OUTPUT CIRCUITS PD_VCC LFA_VCC 5k 5k 500 GS1522 LFA 10k 10k 40 31p 40 5mA 100A PD_VEE 50 LFA_VEE VCO VCO Fig. 4 LFA Circuit Fig. 1 VCO/VCO Input Circuit LFA_VCC PD_VCC 25k 10k 10k DM LFS 400A 85A LFA_VEE DFT_VEE Fig. 5 LFS Output Circuit Fig. 2 DM Output Circuit LFA_VCC PD_VCC 20k 10k 10k PLCAP 5k PLCAP LFS 100A 100A 100A PD_VEE 100A 100A LFA_VEE Fig. 3 PLCAP/PLCAP Output Circuit Fig. 6 LFS Input Circuit 7 of 20 GENNUM CORPORATION 522 - 26 - 03 VCC3 2k BIAS PD_VCC 10k GS1522 10k D0 - D19, SYNC_DETECT_DISABLE PLL_LOCK PD_VEE VEE3 All on-chip resistors have 20% tolerance at room temperature. Fig. 7 PLL_LOCK Output Circuit Fig. 10 Data Input and SYNC_DETECT_DISABLE Circuit VCC 1k PD_VCC 10k BIAS IJI PCLK_IN 5k 5k VCC 30k A VEE PD_VEE Fig. 8 IJI Output Circuit Fig. 11 PCLK_IN Circuit VCC 20k SDO SDO BIAS RESET 10k + CD_VEE VEE RSET Fig. 9 SDO/SDO Output Circuit Fig. 12 RESET Circuit 8 of 20 GENNUM CORPORATION 522 - 26 - 03 VCC 5k 5k BIAS GS1522 BYPASS 10k VEE Fig. 13 BYPASS Circuit DETAILED DESCRIPTION The GS1522 HDTV Serializer is a bipolar integrated circuit used to convert parallel data into serial format according to the SMPTE 292M standard. The device encodes both 8-bit and 10-bit TTL compatible parallel signals producing a serial data rate of 1.485Gb/s. The device operates from a single 5V supply and is available in a 128 pin MQFP package. The functional blocks within the device include the input latches, interleaver, sync detector, parallel to serial converter, SMPTE scrambler, NRZ to NRZ(I) converter, two internal cable drivers, PLL for 20x parallel clock multiplication and lock detect circuitry. 1. INPUT LATCHES The 20-bit input latch accepts either 3.3V or 5V CMOS/TTL inputs. The input data is buffered and then latched on the rising edge of the PCLK_IN pin (2). The output of the latch is a differential signal for increased noise immunity. Further noise isolation is provided by the use of separate power supplies. 2. INTERLEAVER The interleaver takes the 20-bit wide parallel data (Y and C) and reduces it internally to a 10-bit wide word by alternating the Y and C data words according to SMPTE 292M, section 6.1. 3. SYNC DETECTOR The sync detector looks for the reserved words 000-003 and 3FC-3FF in 10-bit hexadecimal, or 00-03 and FC-FF in 8-bit hexadecimal used in the TRS-ID sync word. When there is an occurrence of all zeros or all ones in the eight higher order bits, the lower two bits are forced to zeros or ones respectively. This allows the system to be compatible with 8-bit and 10-bit data. For non-SMPTE standard parallel data, a logic input Sync Detect Disable pin (96) is available to disable this feature. 4. SCRAMBLER The scrambler is a linear feedback shift register used to pseudo-randomize the incoming data according to the fixed polynomial (X9+X4+1). This minimizes the DC component in the output serial stream. The NRZ to NRZ(I) converter uses another polynomial (X+1) to convert a long sequence of ones to a series of transitions, minimizing polarity effects. To disable these features, set the BYPASS pin (16) HIGH. 5. SLEW PHASE LOCK LOOP (S-PLL) An innovative feature of the GS1522 is the slew phase lock loop (S-PLL). When a step phase change is applied to the PLL, the output phase gains constant rate of change with respect to time. This behavior is termed slew. Figure 14 shows an example of input and output phase variation over time for slew and linear (conventional) PLLs. Since the slewing is a non-linear behavior, the small signal analysis cannot be done in the same way as it is for the standard PLL. However, it is still possible to plot input jitter transfer characteristics at a constant input jitter modulation. Slew PLLs offer several advantages such as excellent noise immunity. The loop corrects small input jitter modulation immediately because of the infinite bandwidth. Therefore, the small signal noise of the VCO is cancelled immediately. The GS1522 uses a very clean, external VCO called the GO1515 (refer to the GO1515 Data Sheet for details). Another advantage is the bi-level digital phase detector which provides constant loop bandwidth that is predominantly independent of the data transition density. The loop bandwidth of a conventional tri-stable charge 9 of 20 GENNUM CORPORATION 522 - 26 - 03 pump drops with reducing data transitions. During pathological signals, the data transition density reduces from 0.5 to 0.05 but the slew PLL's performance does not change significantly. PHASE ALIGNMENT EDGE IN-PHASE CLOCK Because most of the PLL circuitry is digital, it is very robust as digital systems are generally more robust than their analog counterparts. Signals which represent the internal functionality, like DM (86), can be generated without adding additional artifacts. Thus, system debugging is possible with these features. PHASE (UI) 0.2 INPUT 0.1 INPUT CLOCK WITH JITTER OUTPUT DATA Fig. 15 Phase Detector Characteristics During pathological signals, the amount of jitter that the phase detector will add can be calculated. By choosing the proper loop bandwidth, the amount of phase detector induced jitter can also be limited. Typically, for a 1.41MHz loop bandwidth at 0.2UI input jitter modulation, the phase detector induced jitter is about 0.015UIp-p. This is not significant, even in the presence of pathological signals. OUTPUT 5.2. Charge Pump The charge pump in a slew PLL is different from the charge pump in a linear PLL. There are two main functions of the charge pump: to hold the frequency information of the input data and to provide a binary control voltage to the VCO. 0.0 SLEW PLL RESPONSE The charge pump holds the frequency information of the input data. This information is held by CCP1 which is connected between LFS (82) and LFS (84). CCP2, which is connected between LFS and LFA_VEE (89), is used to remove common mode noise. Both CCP1 and CCP2 should have the same value. 0.2 PHASE (UI) 0.8UI GS1522 The complete slew PLL is made up of several blocks including the phase detector, the charge pump and an external Voltage Controlled Oscillator (VCO) which are described in the following sections. Phase lock loop frequency synthesis and lock logic are also described. RE-TIMING EDGE INPUT 0.1 OUTPUT 0.0 LINEAR (CONVENTIONAL) PLL RESPONSE Fig. 14 PLL Characteristics 5.1. Phase Detector The phase detector portion of the slew PLL used in the GS1522 is a bi-level digital phase detector. It indicates whether the data transition occurred before or after with respect to the falling edge of the internal clock. When the phase detector is locked, the data transition edges are aligned to the falling edge of the clock. The input data is then sampled by the rising edge of the clock, as shown in Figure 15. In this manner, the allowed input jitter is 1UI p-p in an ideal situation. However, due to setup and hold time, the GS1522 typically achieves 0.8UI p-p input jitter tolerance without causing any errors in this block. When the signal is locked to the internal clock, the control output from the phase detector is refreshed at the transition of each rising edge of the data input. During this time, the phase of the clock drifts in one direction. The charge pump provides a binary control voltage to the VCO depending upon the phase detector output. The output pin LFA (90) controls the VCO. Internally there is a 500 pull-up resistor which is driven with a 100A current called P. Another analog current F, with 5mA maximum drive proportional to the voltage across the CCP1, is applied at the same node. The voltage at the LFA node is VLFA_VCC - 500(P+F) at any time. Because of the integrator, F changes very slowly whereas P can change at the positive edge of the data transition as often as a clock period. In the locked position, the average voltage at LFA (VLFA_VCC - 500(P/2+F) is such that VCO generates frequency equal to the data rate clock frequency. Since P is changing all the time between 0A and 100A, there are two levels generated at the LFA output. 5.3. VCO The GO1515 is an external hybrid VCO which has a centre frequency of 1.485GHz. It is guaranteed to provide 1.485/1.001GHz within the control voltage (3.1V - 4.65V) of the GS1522 over process, power supply and temperature. 10 of 20 GENNUM CORPORATION 522 - 26 - 03 The GO1515 is a very clean frequency source and, because of the internal high Q resonator, is an order of magnitude more immune to external noise as compared to on-chip VCOs. The LBCONT pin (91) is used to adjust the loop bandwidth by externally changing the internal charge pump current. For maximum loop bandwidth, connect LBCONT to the most positive power supply. For medium loop bandwidth, connect LBCONT through a pull-up resistor (RPULL-UP). For low loop bandwidth, leave LBCONT floating. The formula below shows the change in the loop bandwidth using RPULL-UP. 5.4. Phase Lock Loop Frequency Synthesis The GS1522 requires the HDTV parallel clock (74.25 or 74.25/1.001MHz) to synthesize a serial clock which is 20 times the parallel clock frequency (1.485MHz) using a phase locked loop (PLL). This serial clock is then used to strobe the output serial data. Figure 16 illustrates this operation. The VCO is normally free-running at a frequency close to the serial data rate. A divide-by-20 circuit converts the free running serial clock frequency to approximately that of the parallel clock. Within the phase detector, the dividedby-20 serial clock is then compared to the reference parallel clock from the PCLK_IN pin (2). Based on the leading or lagging alignment of the divided clock to the input reference clock, the serial data output is synchronized to the incoming parallel clock. where LBWNOMINAL is the loop bandwidth when LBCONT is left floating. 7. LOOP BANDWIDTH OPTIMIZATION Since the feed back loop has only digital circuits, the small signal analysis does not apply to the system. The effective loop bandwidth scales with the amount of input jitter modulation index. The following table summarizes the relationship between input jitter modulation index and bandwidth when RCP1 and CCP3 are not used. See the Typical Application Circuit for the location of RCP1 and CCP3 . TABLE 1: Relationship Between Input Jitter Modulation Index and Bandwidth GS1522 PLL PCLK_IN ( 25k + R PULL - UP ) LBW = LBW NOMINAL x -----------------------------------------------------( 5k + R PULL - UP ) PHASE DETECTOR DIVIDE-BY-20 GO1515 VCO INPUT JITTER MODULATION INDEX BANDWIDTH BW JITTER FACTOR (jitter modulation x BW) 0.05 5.657MHz 282.9kHzUI 0.10 2.828MHz 282.9kHzUI 0.20 1.414MHz 282.9kHzUI 0.50 565.7kHz 282.9kHzUI Fig. 16 Phase Lock Loop Frequency Synthesis 5.5. Lock Logic Logic is used to produce the PLL_LOCK (15) signal which is based on the LFS signal and phase lock signal. When there is no data input, the integrator charges and eventually saturates at either end. By sensing the saturation of the integrator, it is determined that no data is present. If there is no data present or phase lock is low, the lock signal is made LOW. Logic signals are used to acquire the frequency by sweeping the integrator. Injecting a current into the summing node of the integrator achieves the sweep. The sweep is disabled when phase lock is asserted. The direction of the sweep is changed when LFS saturates at either end. The product of the input jitter modulation (IJM) and the bandwidth (BW) is a constant. In this case, it is 282.9kHzUI. The loop bandwidth automatically reduces with increasing input jitter, which results in the cleanest signal possible. Using a series combination of RCP1 and CCP3 in parallel to an on-chip resistor (see the Typical Application Circuit) can reduce the loop bandwidth of the GS1522. The parallel combination of the resistors is directly proportional to the bandwidth factor. For example, the on-chip 500 resistor yields 282.9kHzUI. If a 50 resistor is connected in parallel, the effective resistance will be (50:500) 45.45. This resistance yields a bandwidth factor of [282.9 x (45.45/500)] = 25.72kHzUI The capacitance CCP3 in series with the RCP1 should be chosen such that the RC factor is 50F. For example, RCP1=50 requires CCP3=1F. 11 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 The VCO gain, K, is nominally 16MHz/V. The control voltage around the average LFA voltage is 500 x P/2. This produces two frequencies off from the centre by = K x 500 x P/2. 6. LBCONT The K of the VCO (GO1515) is specified with a minimum of 11MHz/V and maximum of 21MHz/V which is about 32% variation. The 500 x P/2 varies about 10%. The resulting bandwidth factor varies by approximately 45% when no RCP1 and CCP3 are used. P by itself may vary by 30% so the variability for lower bandwidths increases by an additional 30%. The CCP1 and CCP2 capacitors should be changed with reduced bandwidths. Smaller CCP1 and CCP2 capacitors result in jitter peaking, lower stability, less probability of locking but at the same time lowering the asynchronous lock time. Therefore, there is a trade-off between asynchronous lock time and jitter peaking/stability. These capacitors should be as large as possible for the allowable lock time and should be no smaller than the allowed value. With the recommended values, jitter peaking of less than 0.1dB has been measured at the lower loop bandwidth as shown in Figure 17. At higher loop bandwidths, it is difficult to measure jitter peaking because of the limitation of the measurement unit. It has been determined that for 282.9kHzUI, the minimum value of the CCP1 and CCP2 capacitors should be no less than 0.5F. For added margin, 1F capacitors are recommended. The 1F value gives a lock time of about 60ms in one attempt. For 25.72kHzUI, these capacitors should be no less than 5.6F. This results in 340ms of lock time. If necessary, extra margin can be built by increasing these capacitors at the expense of a longer asynchronous lock time. Bandwidths lower than 129kHz at 0.2UI modulation have not been characterized, but it is believed that the bandwidth could be further lowered (contact Gennum's Video Products Applications for further details). Since a lower bandwidth has less correction for noise, extra care should be taken to minimize board noise. Figures 18 and 19 show the two measured loop bandwidths at these two settings. Table 2 summarizes the two bandwidth settings. Fig. 18 Typical Jitter Transfer Curve at Setting A in Table 2 Fig. 17 Typical Jitter Peaking However, because relatively larger CCP1 and CCP2 capacitors can be used, over-damping of the loop response occurs. An accurate jitter peaking measurement of 0.1dB for the GS1522 requires the modulation source to have a constant amount of jitter modulation index (within 0.1dB or 1.2%) over the frequency range beyond the loop bandwidth. Fig. 19 Typical Jitter Transfer Curve at Setting B in Table 2 12 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 The synchronous lock time increases with reduced bandwidth. Nominal synchronous lock time is equal to [ 0.25 x 2 /Bandwidth factor]. That is, the default bandwidth factor (282.9kHzUI) yields 1.25s. For 25.72kHzUI, the synchronous lock time is 0.3535/25.72k = 13.75s. Since the CCP1, CCP2 and CCP3 are also charged, it is measured to be about 11s which is slightly less than the calculated value of 13.75s. TABLE 2: Loop Bandwidth Setting Options RCP1 CCP3 CCP1 CCP2 BW FACTOR BW at 0.2 UI JITTER MODULATION INDEX ASYNCHRONOUS SYNCHRONOUS A Open Open 1.0 1.0 282.9kHz 1.41MHz 60ms 1.25s B 50 1.0 5.6 5.6 25.72kHz 129kHz 340ms 11.0s 9. INPUT JITTER INDICATOR (IJI) The phase lock circuit is used to determine the phase locked condition. It is done by generating a quadrature clock by delaying the in-phase clock by 166ps (0.25UI at 1.5GHz) with the tolerance of 0.05UI. The in-phase clock is the clock whose falling edge is aligned to the data transition. When the PLL is locked, the falling edge of the inphase clock is aligned with the data edges as shown in Figure 20. The quadrature clock is in a logic HIGH state in the vicinity of input data transitions. The quadrature clock is sampled and latched by positive edges of the data transitions. The generated signal is low pass filtered with an RC network. The R is an on-chip 6.67k resistor and CPL is an internal capacitor (31pF). The time constant is about 200ns. This signal indicates the amount of excessive jitter which occurs beyond the quadrature clock window (greater than 0.5UI, see Figure 19). All the input data transitions occurring outside the quadrature clock window are captured and filtered by the low pass filter as mentioned in section 8, Phase Lock. The running time average of the ratio of the transitions inside the quadrature clock and outside the quadrature is available at the PLCAP/PLCAP pins (87 and 85). IJI, which is the buffered signal available at the PLCAP, is provided so that loading does not effect the filter circuit. The signal at IJI is referenced with the power supply such that the factor VIJI /V CC is a constant over process and power supply for a given input jitter modulation. The IJI signal has 10k output impedance. Figure 21 shows the relationship of the IJI signal with respect to the sine wave modulated input jitter. PHASE ALIGNMENT EDGE RE-TIMING EDGE TABLE 3: IJI Voltage as a Function of Sinusoidal Jitter IN-PHASE CLOCK 0.8UI INPUT CLOCK WITH JITTER 0.25UI QUADERATURE CLOCK PLCAP SIGNAL PLCAP SIGNAL P-P SINE WAVE JITTER IN UI IJI VOLTAGE 0.00 4.75 0.15 4.75 0.30 4.75 0.39 4.70 0.45 4.60 0.48 4.50 0.52 4.40 0.55 4.30 0.58 4.20 0.60 4.10 0.63 3.95 Fig. 20 PLL Circuit Principles If the signal is not locked, the data transition phase could be anywhere with respect to the internal clock or the quadrature clock. In this case, the normalized filtered sample of the quadrature clock is 0.5. When VCO is locked to the incoming data, data will only sample the quadrature clock when it is logic HIGH. The normalized filtered sample quadrature clock is 1.0. We chose a threshold of 0.66 to generate the phase lock signal. Because the threshold is lower than 1, it allows jitter to be greater than 0.5UI before the phase lock circuit reads it as "not phase locked". 13 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 8. PHASE LOCK 5.0 IJI SIGNAL (V) 4.8 4.6 4.4 4.2 GS1522 4.0 3.8 3.6 0.00 0.20 0.40 0.60 0.80 INPUT JITTER (UI) Fig. 21 Input Jitter Indicator (Typical at TA = 25C) 10. JITTER DEMODULATION (DM) Fig. 22 Jitter Demodulation Signal The differential jitter demodulation (DM) signal is available at the DM pin (86). This signal is the phase correction signal of the PLL loop, which is amplified and buffered. If the input jitter is modulated, the PLL tracks the jitter if it is within loop bandwidth. To track the input jitter, the VCO has to be adjusted by the phase detector via the charge pump. Thus, the signal which controls the VCO contains the information of the input jitter modulation. The jitter demodulation signal is only valid if the input jitter is less than 0.5UIp-p. The DM signal has a 10k output impedance, which can be low pass filtered with appropriate capacitors to eliminate high frequency noise. DFT_VEE (88) should be connected to GND to activate the DM signal. The DM signal can be used as a diagnostic tool. Assume there is an HDTV SDI source which contains excessive noise during the horizontal blanking because of the transient current flowing in the power supply. To discover the source of the noise, probe around the source board with a low frequency oscilloscope (Bandwidth < 20MHz) that is triggered with an appropriately filtered DM signal. The true cause of the modulation is synchronous and appears as a stationary signal with respect to the DM signal. Figure 22 shows an example of such a situation. An HDTV SDI signal is modulated with a signal causing about 0.2UI jitter (Channel 1). The GS1522 receives this signal and locks to it. Figure 22 (Channel 2) shows the DM signal. Notice the wave shape of the DM signal, which is synchronous to the modulating signal. The DM signal can also be used to compare the output jitter of the HDTV signal source. 11. MUTE The logic controls the mute block when the PLL_LOCK (15) signal has a LOW logic state. When the mute signal is asserted, the previous state of the output is latched. 12. CABLE DRIVER The outputs of the GS1522 are complementary current mode cable driver stages. The output swing and impedance can be varied. Use Table 4 to select the RSET resistor for the desired output voltage level. Linear interpolation can be used to determine the specific value of the resistor for a given output swing at the load impedance. For linear interpolation, use either Figure 23 or the information in Table 4. Find the admittance and then, by inverting the admittance, a resistor value for the RSET can be found. The output can be used as dual 0.8V 75 cable drivers. It can also be used as a differential transmission line driver. In this case, the pull-up resistor should match the impedance of the transmission line because the pull-up resistor acts as the source impedance. To reduce the swing and save power, use a higher value of RSET resistor. There are HD-LINXTM products that can handle such low input swings. NOTE: For reliability, the minimum RSET resistor cannot be less than 50 because of higher current density. 14 of 20 GENNUM CORPORATION 522 - 26 - 03 0.8 0.6 75 0.4 GS1522 SOURCE/END TERMINATED OUTPUT SWING (V) 1.0 50 0.2 0.0 0.00 0.01 0.02 0.03 1/RSET () Fig. 23 Signal Swing for Various R SET Admittances When the outputs are used to differentially drive another device such as the GS1508, use 50 transmission lines with the smallest possible signal swing while allowing 10% variation at the output swing to select the correct RSET resistor. To drive the GS1508, the recommended RSET resistor is 150. There is no need to compensate for the return-loss in this situation. The uncompensated waveform at the output is shown in Figure 24. Fig. 24 Uncompensated Output Eye Waveform Fig. 25 Compensated Output Eye Waveform NOTE: Figures 24 and 25 show the waveforms on an oscilloscope using a 75 to 50 pad. TABLE 4: RSET Values for Various Output Load Conditions OUTPUT CURRENT TRANSMISSION LINE, TERMINATED AT THE END. (PULL-UP RESISTOR AT THE SOURCE = 75) TRANSMISSION LINE, TERMINATED AT THE END. (PULL-UP RESISTOR AT THE SOURCE = 50) 0.0020 2.506mA 0.094V 0.063V 150.0 0.0067 7.896mA 0.296V 0.197V 75.0 0.0133 15.161mA 0.569V 0.379V 53.6 0.0187 20.702mA 0.776V 0.517V 52.3 0.0192 21.216mA 0.796V 0.530V 49.9 0.0200 22.032mA 0.826V - RSET RESISTOR ADMITTANCE (g) OF THE RSET RESISTOR (= 1/RSET RESISTOR) 500.0 15 of 20 GENNUM CORPORATION 522 - 26 - 03 12. RETURN LOSS Unless the artwork is an exact copy of the recommended layout, verify every design for output return loss. Tweak the layout until a return loss of 25dB is attained while the GS1522 is not mounted and L1 is shorted. When the device is mounted, use different inductors to match the parasitic capacitance of the IC. When the correct inductor is used, maximum return loss of 5MHz to 800MHz is achievable. To increase the return loss 800MHz to 1.5GHz, use a shunt capacitor of 0.5pF to 1.5pF. The larger inductor causes slower rise/fall time. The larger shunt capacitor causes a kink in the output waveform. Therefore, the waveform must be verified to meet SMPTE 292M specifications. There are two levels at the output depending upon the output state (logic HIGH or LOW). When taking measurements, latch the outputs in both states. An interpolation is necessary because the actual output node voltages are different when a stream of data is passing as compared to the static situation created when measuring return loss. See the GS1508 Preliminary Data Sheet for more information. GS1522 In an application where the GS1522 directly drives a cable, it is possible to achieve an output return loss (ORL) of about 17dB to 1.485GHz. PCB layout is very important. Use the EB1522 as a reference layout (see Figures 28 to 31). When designing high frequency circuits, use very small `0608' surface mount components with short distances between the components. To reduce PCB parasitic capacitance, provide openings in the ground plane. For best matching, a 12nH inductor in parallel with a 75 resistor and a 1.5pF capacitor matches the 75 cable impedance. The inductor and resistor cancel the parasitic capacitance while the capacitor cancels the inductive effect of the bond wire. To verify the performance of any layout, measure the return loss by shorting the inductor with a piece of wire without the GS1522 installed. Fig. 26 Compensated Output Return Loss at Logic HIGH Fig. 27 Compensated Output Return Loss at Logic LOW 16 of 20 GENNUM CORPORATION 522 - 26 - 03 PCLK D1_0 D1_1 D1_2 D1_3 D1_4 D1_5 D1_6 D1_7 D1_8 D1_9 D1_10 D1_11 D1_12 D1_13 D1_14 D1_15 D1_16 D1_17 D1_18 D1_19 C19 10 100n C20 VCC SYNC_DETECT_DISABLE 10 C17 0 C21 R6 124 DATA_IN[4] 125 DATA_IN[3] 126 DATA_IN[2] 127 DATA_IN[1] 128 DATA_IN[0] 118 DATA_IN[8] 119 DATA_IN[7] 120 nc 121 nc 122 DATA_IN[6] 123 DATA_IN[5] 116 nc 117 nc 109 nc 110 DATA_IN[14] 111 DATA_IN[13] 112 DATA_IN[12] 113 DATA_IN[11] 114 DATA_IN[10] 115 DATA_IN[9] 106 DATA_IN[16] 107 DATA_IN[15] 108 nc 103 DATA_IN[19] 104 DATA_IN[18] 105 DATA_IN[17] L8 L5 All resistors in ohms, all capacitors in farads, unless otherwise shown. C18 100n VCC C46 100n C5 10n C47 10 VCC VCC L7 10 C45 10n C1 LBCONT LOOP FILTER COMPONENTS 1 CCP2 + 100n C48 VCC JMP NOTE: R35 IS AN OPTIONAL 1k RESISTOR. LEAVE FLOATING. R35 OPTIONAL 1 CCP1 + 10n VCC C4 10n C6 NOTE: L3 to L8 are 0 RESISTORS. USE 12nH INDUCTORS IN NOISY ENVIRONMENTS. GS1522 JMP R36 NOTE: R36 IS AN OPTIONAL 0 RESISTOR. LEAVE FLOATING. VCC nc 83 L6 LFS 82 81 nc nc 80 79 VCC 4 nc 5 nc nc 102 1 V EE3 nc 99 98 nc nc 97 96 SYNC_DETECT_DISABLE VEE3 95 VCC3 94 93 nc LFA LFA 90 VCO PDSUB_VEE 77 PD_VEE 76 VCO 75 VCO 74 TYPICAL APPLICATION CIRCUIT 3 nc PCLK_IN IJI nc 101 nc 100 2 LFS DM 86 PLCAP 85 84 LBCONT 92 LFA_VCC 6 nc 7 nc 8 nc 9 nc 10 BUF_VEE 11 nc IJI 78 PD_VCC 91 LBCONT 12 nc 13 XDIV20 nc 70 nc 69 VCC 470n 10n C16 C12 33 nc 34 nc LFA_VEE 89 DFT_VEE 88 PLCAP 87 BYPASS 14 nc 15 PLL_LOCK 16 BYPASS PLL_LOCK nc 73 nc 72 nc 71 17 RESET 18 VEE2 19 nc 20 nc 21 VCC2 22 VCC2 23 VCC2 24 VCC2 25 V CC2 26 V EE2 27 VEE2 28 V EE2 29 V EE2 30 V EE2 31 SDO1_EN 32 nc RESET nc 68 nc 67 35 nc 36 nc C13 100n VCC C40 10 59 60 61 62 RSET L4 L3 C7 12nH R4 1p5 L1 42 43 41 nc nc 40 nc 39 nc nc SET1 nc 50 49 SDO1 48 SDO_nc 47 SDO1 46 nc VCC2 45 44 R VCC 1p5 12nH C11 75 L2 C8 10n nc 52 nc 51 R2 75 VCC 100n R3 75 VCC C15 75 R5 10 C14 SDO_nc 54 SDO0 53 RSET0 58 VCC2 57 V 52.3 CC 56 nc SDO0 55 VEE2 nc nc nc OSC_VEE 64 A0 63 nc 66 nc 65 37 nc 38 nc 17 of 20 GS1522 GENNUM CORPORATION 522 - 26 - 03 J4 BNC_ANCHOR J2 J1 BNC_ANCHOR SECOND PAIR OF BNC SHOWN IS FOR DUAL FOOTPRINT OPTION ON INPUT CONNECTORS C9 + 47 C10 + 47 J3 TYPICAL APPLICATION CIRCUIT (continued) GO1515 VCO POWER CONNECT LFA VCC C37 C41 + 100n VCC 10 C38 + C44 RCP1 VCTR 1 GND 50 8 CCP3 + 1 GS1522 LOCK DETECT 7 nc 2 GND 6 GND U2 GND GO1515 5 O/P 4 100n GS1522 VCC 3 10 VCC R22 R25 LOCK VCO GS1522 SYNC DETECT DISABLE (10BIT/8BIT) LED1 22k VCC VCC BYPASS HDR1 HDR5 S1 SYNC_DETECT_DISABLE 150 GS1522 RESET CIRCUIT GS1522 SCRAMBLER BYPASS VCC Q1 RESET 1 2 3 4 R20 4k7 All resistors in ohms, all capacitors in farads, unless otherwise shown. The figures above show the recommended application circuit for the GS1522. The external VCO is the GO1515 and is specifically designed to be used with the GS1522. Figures 28 through 31 show an example PC board layout of the GS1522 IC and the GO1515 VCO. This application board layout does not reflect every detail of the typical application circuit. It is provided as a general guide to the location of the critical parts. Fig. 28 Top Layer of EB1522 PCB Layout Fig. 29 Ground Layer of EB1522 PCB Layout 18 of 20 GENNUM CORPORATION 522 - 26 - 03 GS1522 Fig. 31 Bottom Layer of EB1522 PCB Layout Fig. 30 Power Layer of EB1522 PCB Layout APPLICATION INFORMATION Please refer to the EBHDTX documentation for more detailed application and circuit information on using the GS1522 with the GS1501 and GS1511 Formatters. 19 of 20 GENNUM CORPORATION 522 - 26 - 03 PACKAGE DIMENSIONS 23.20 0.25 20.0 0.10 18.50 REF GS1522 12 TYP 0.75 MIN 17.20 0.25 12.50 REF 0 -7 0.30 MAX RADIUS 14.0 0.10 0-7 0.13 MIN. RADIUS 0.88 0.15 1.6 REF 3.00 MAX 0.50 BSC 2.80 0.25 128 pin MQFP All dimensions are in millimetres. 0.27 0.08 CAUTION ELECTROSTATIC SENSITIVE DEVICES DO NOT OPEN PACKAGES OR HANDLE EXCEPT AT A STATIC-FREE WORKSTATION DOCUMENT IDENTIFICATION REVISION NOTES: Added Pb-free and green information. For latest product information, visit www.gennum.com DATA SHEET The product is in production. Gennum reserves the right to make changes at any time to improve reliability, function or design, in order to provide the best product possible. GENNUM CORPORATION MAILING ADDRESS: P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3 Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 SHIPPING ADDRESS: 970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5 GENNUM JAPAN CORPORATION Shinjuku Green Tower Building 27F 6-14-1, Nishi Shinjuku Shinjuku-ku, Tokyo 160-0023 Japan Tel: +81 (03) 3349-5501 Fax: +81 (03) 3349-5505 GENNUM UK LIMITED 25 Long Garden Walk, Farnham, Surrey, England GU9 7HX Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523 Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. (c) Copyright May 2000 Gennum Corporation. All rights reserved. Printed in Canada. 20 of 20 522 - 26 - 03