THIS SPEC IS OBSOLETE
Spec No: 001-97334
Spec Title: CY5676A PROC(TM) BLE 256KB MODULE
Replaced by: NONE
CY5676A PROCTM BLE 256KB MODULE
Wiggle antenna
32.768-kHz crystal
(bottom side)
Cmod
Ctank
Antenna matching
network (AMN)
4-pin UART header
SAR bypass capacitor
(bottom side)
24-MHz crystal
GND VDDA
P3_6 P3_7
P3_4 P3_5
P3_2 P3_3
P3_0 P3_1
P4_0 P5_1
P4_1 P5_0
P2_6 P2_7
P2_4 P2_5
P2_2 P2_3
P2_0 P2_1
VDDR GND
P0_1 P0_0
P0_3 P0_2
P0_5 P0_4
P1_0 VREF
P1_2 P1_1
P0_6 P1_4
P0_7 P1_3
XRES P1_5
GND P1_7
VDDD P1_6
VDD
GND
P1_4
P1_5
CYBL11573-56LQXI
PRoC BLE device
Note: To apply power to the module, apply 1.9 V - 5.0 V to any of the VDD pins (VDD,
VDDD, VDDA, or VDDR) and 0 V to any GND pin
Fig-1: Pinout Description for CY5676A
CY5676A PRoCTM BLE 256KB Module is a complete solution to add BLE connectivity
to any embedded system with Bluetooth® 4.2 features. The module features a
PRoC BLE device (CYBL11573-56LQXI), 24-MHz and 32.768-kHz crystals, a PCB
antenna, and other passives while providing access to all GPIOs of the device.
For more information on Cypress’s BLE solutions visit www.cypress.com/BLE
PRoC BLE is a single-chip solution with a 48-MHz ARM® Cortex®-M0 CPU,
Bluetooth 4.2 radio, CapSense® technology for touch-sensing, two serial
communication blocks (SCBs), a 12-bit ADC, four Timer/Counter/PWMs, four
additional PWMs, I2S for digital audio, and segment LCD direct-drive capability.
CY5676A PROCTM BLE 256KB MODULE
© 2015-2018 Cypress Semiconductor Corporation. All rights reserved.
All trademarks or registered trademarks referenced herein are the
properties of their respective owners. 001-97334 Rev.*D
For more information about this kit, visit www.cypress.com/CY5676A
Fig-3: Programming and Debugging with CY8CKIT-042-BLE Pioneer Baseboard
Fig-2: Programming and Debugging with CY8CKIT-002 MiniProg3
STANDALONE USE WITH PSOC CREATORTM IDE AND CY8CKIT-002 MINIPROG3
Step 1: Plug the module on the CY8CKIT-042-BLE Pioneer Kit Baseboard.
Step 2: Create your design in PSoC Creator IDE and use the BLE Pioneer Kit to
program and debug.
The CY5676A module is intended for development purposes only. Users are advised
to test and evaluate this module in an RF development environment. This module is
not a nished product and when assembled may not be resold or otherwise
marketed unless all required authorizations are rst obtained.
Contact support@cypress.com for details.
USING THE PROC BLE MODULE WITH THE CY8CKIT-042-BLE PIONEER KIT
Pin Mapping
CY8CKIT-002
VTARG
GND
RES
SCLK
SDAT
CY5676A
VDDD
GND
XRES
P0_7
P0_6
Step 1: Select the 5-pin connector setting in PSoC Creator or PSoC Programmer.
Step 2: Use 0.1” male headers (not included) or jumper wires to connect the
MiniProg3 to the module.
