TEA19161T Digital controller for high-efficiency resonant power supply Rev. 1 -- 10 March 2016 Product data sheet 1. General description The TEA19161T is a fully digital controller for high-efficiency resonant power supplies. Together with the TEA19162T PFC controller and the TEA1995T dual SR controller, a complete resonant power supply can be built which is easy to design and has a very low component count. This power supply meets the efficiency regulations of Energy Star, the Department of Energy (DoE), the Eco-design directive of the European Union, the European Code of Conduct, and other guidelines. So, any auxiliary low-power supply can be omitted. In contrast to traditional resonant topologies, the TEA19161T (LLC) shows a high efficiency at low loads due to the newly introduced low-power mode. This mode operates in the power region between continuous switching (also called high-power mode) and burst mode. Because the TEA19161T is regulated via the primary capacitor voltage, it has accurate information about the power delivered to the output. The measured output power defines the mode of operation (burst mode, low-power mode or high-power mode). A configuration pin can easily set the transition levels of the operating modes. The TEA19161T contains a low-voltage die with a fully digital controller for output power control, start-up, initializations, and protections. These protections include OverCurrent Protection (OCP), OverVoltage Protection (OVP), Open-Loop Protection (OLP), and Capacitive Mode Regulation (CMR). It also contains a high-voltage Silicon-On-Insulator (SOI) controller for high-voltage start-up, integrated drivers, level shifter, protections, and circuitry assuring zero-voltage switching. The TEA19161T is designed to cooperate with the TEA19162T Power Factor Control (PFC) controller. For communications about start-up and protections, the TEA19161T contains a digital control interface. The digital control enables a fast latch reset mechanism. It maximizes the overall system efficiency at low output power levels by setting the TEA19162T to operate in burst mode. The TEA19161T/TEA19162T/TEA1995T combination gives an easy to design, highly efficient and reliable power supply, providing 90 W to 500 W, with a minimum of external components. The system provides a very low no-load input power (< 75 mW; total system including the TEA19161T/TEA19162T/TEA1995T combination) and high efficiency from minimum to maximum load. So, any additional low-power supply can be omitted, ensuring a significant system cost saving and highly simplified power supply design. TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 2. Features and benefits 2.1 Distinctive features Complete functionality as a combination with TEA19162T Integrated high-voltage start-up Integrated high-voltage Level Shifter (LS) Extremely fast start-up (< 500 ms at Vmains = 100 V (AC)) Continuously VSUPIC regulation via the SUPHV pin during start-up and protection, allowing minimum SUPIC capacitor values Operating frequencies are outside the audible area at all operating modes Integrated soft start Power good function Maximum 500 kHz half-bridge switching frequency 2.2 Green features Extremely high efficiency from low load to high load Compliant with Energy using Product directive (EuP) lot 6 Excellent no-load input power (< 75 mW for TEA19161T/TEA19162T/TEA1995T combination) Regulated low optocurrent, enabling low no-load power consumption Very low supply current during non-switching state in burst mode Transition between different operation modes (high-power/low-power/burst mode) occur at integrated, externally adjustable power levels Adaptive non-overlap time 2.3 Protection features Supply UnderVoltage Protection (UVP) OverPower Protection (OPP) Integrated adjustable overpower time-out Adjustable latch or restart function for OverPower Protection On-chip OverTemperature Protection (OTP) Capacitive Mode Regulation (CMR) Accurate OverVoltage Protection (OVP) Maximum on-time protection for low-side and high-side driver output OverCurrent Protection (OCP) Disable input 3. Applications TEA19161T Product data sheet Desktop and all-in-one PCs LCD television Notebook adapter Printers All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 2 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 4. Ordering information Table 1. Ordering information Type number TEA19161T TEA19161T Product data sheet Package Name Description Version SO16 plastic small outline package; 16 leads; body width 3.9 mm; body thickness SOT109-3 1.47 mm All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 3 of 46 xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx NXP Semiconductors TEA19161T Product data sheet 5. Block diagram 683+9 , 683,& 6835(* 9 6(77,1*6 &21752/ 616287 &21752/ 6833/< VXSLFBFKDUJH LQWHUQDOVXSSOLHV VHWWLQJ , VHWWLQJ 8936835(* 616287 6166(7 893683,& '5,9(56 $' 7($ 62)767$57 3)&&21752/ *DWH+6 /6 *$7(+6 , VHWWLQJ 6835(* 3)&EXUVW 32:(5 &21752/ 616%2267 3)&SURWHFWLRQ VWDUWXS *DWH/6 9KV 616&$3 *$7(/6 9OV 616&$3 9 6:,7&+,1*&21752/ , *DWH+6 *DWH/6 )(('%$&.&21752/ 23(5$7,2102'( $' 997 9 616)% 3ORZSZU V U T %8567 &<&/(6 EXUVWRQ , 9$//(< 3($. '(7(&7 2&3 &05 +% 9 616&85 9 N 9 ,ELDV 616&$3 273 616&$3 DDD TEA19161T 4 of 46 (c) NXP Semiconductors N.V. 2016. All rights reserved. 9 Block diagram 3 N 9 Fig 1. 6:,7&+,1* 67$7( 0$&+,1( ORZSRZHU PRGH Digital controller for high-efficiency resonant power supply Rev. 1 -- 10 March 2016 All information provided in this document is subject to legal disclaimers. 683+6 &21752/ /2*,& TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 6. Pinning information 6.1 Pinning 683,& 616%2267 616)% 616&$3 616287 616&85 *1' 6166(7 ,& 6835(* QF *$7(/6 +% QF 683+6 683+9 *$7(+6 DDD Fig 2. TEA19161T pin configuration (SOT109-3) 6.2 Pin description Table 2. Pin description Symbol Pin Description SUPIC 1 input supply voltage and output of internal HV start-up source; externally connected to an auxiliary winding of the LLC via a diode or to an external DC supply SNSFB 2 output voltage regulation feedback sense input; externally connected to an optocoupler SNSOUT 3 sense input for setting the burst frequency and monitoring the LLC output voltage; externally via a resistive divider and a diode connected to the auxiliary winding GND 4 ground SUPREG 5 regulated SUPREG IC supply; internal regulator output; input for drivers; externally connected to SUPREG buffer capacitor GATELS 6 LLC low-side MOSFET gate driver output n.c. 7 not connected SUPHV 8 internal HV start-up source high-voltage supply input; externally connected to (PFC) boost voltage GATEHS 9 LLC high-side MOSFET gate driver output SUPHS 10 high-side driver supply input; externally connected to bootstrap capacitor (CSUPHS) HB 11 low-level reference for high-side driver and input for half-bridge slope detection; externally connected to half-bridge node HB between the LLC MOSFETs n.c. 12 not connected SNSSET 13 settings for transition levels high/low power mode and low-power/burst mode, overpower level, overpower time-out, and restart or latched. Output of the power good signal. SNSCUR 14 LLC current sense input; externally connected to the resonant current sense resistor SNSCAP 15 LLC capacitor voltage sense input; externally connected to divider across LLC capacitor SNSBOOST 16 TEA19161T Product data sheet sense input for boost voltage; output for PFC burst control; externally connected to resistive divided boost voltage All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 5 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7. Functional description 7.1 Supply voltages The TEA19161T includes: * * * * A high-voltage supply pin for start-up (SUPHV) A general supply to be connected to an external auxiliary winding (SUPIC pin) An accurate regulated voltage (SUPREG pin) A floating supply for the high-side driver (SUPHS pin) 7.1.1 Start-up and supply voltage Initially, the capacitors on the SUPIC and SUPREG pins are charged via the SUPHV pin. The SUPHV pin is connected to the output voltage of a PFC via an external resistor. Internally, a high-voltage series switch is located between the SUPHV and SUPIC pins. From the SUPIC pin, the SUPREG pin is supplied using a linear regulator (see Figure 3). 9ERRVW 5683+9 683+9 FXUUHQW OLPLWHU 9UVW 683,& VXSLFBFKDUJH 683,& &683,& 9LQWUHJG 6835(* 6835(* ,& &6835(* DDD Fig 3. TEA19161T HV start-up Initially, when the voltage on the SUPIC pin is below the reset level VrstSUPIC) (3.5 V), the SUPIC charge current is internally limited to Ilim(SUPHV) (0.75 mA). In this way, the dissipation is limited when SUPIC is shorted to ground. When the voltage on the SUPIC pin exceeds Vrst(SUPIC), the internal switch is closed. To limit the IC power dissipation, an external resistor (RSUPHV) is required to reduce the voltage drop between the SUPHV and SUPIC pins when charging the SUPIC capacitor. RSUPHV must be dimensioned such that the maximum current is limited to below limiting value ISUPHV (20 mA) and it can handle the required power dissipation. The maximum power dissipation of the external resistor can be reduced by using several resistors in series. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 6 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply When the SUPIC reaches the Vstart(SUPIC) level (19.1 V), it is continuously regulated to this start level with a hysteresis (Vstart(hys)SUPIC; 0.7 V). It activates the switch between the SUPHV and SUPIC pins when the SUPIC voltage drops to below Vstart(SUPIC) + Vstart(hys)SUPIC. It deactivates the switch when it exceeds Vstart(SUPIC). When start-up is complete and the LLC controller is operating, the LLC transformer auxiliary winding supplies the SUPIC pin. In this operational state, the HV start-up source is disabled (see Figure 4). When the system enters the protection mode, the SUPIC pin is also regulated to the start level. During the non-switching period of the burst mode, the system also activates the switch between the SUPHV and SUPIC pins when the SUPIC voltage drops below Vlow(SUPIC). It regulates the voltage with a hysteresis of Vlow(hys)SUPIC. In this way, the system avoids that the SUPIC undervoltage protection (Vuvp(SUPIC)) is triggered because of a long non-switching period in burst mode. RQ VXSLFBFKDUJH O683,& RII P$ OOLP 683+9 9683,& 9VWDUW 683,& 9VWDUW K\V 683,& 9UVW 683,& RQ SXOOGRZQBVQVERRVW RII 9VWDUW 616%2267 ,616)%!,UHJ 616)% 616%2267 9RXW PRGHRIRSHUDWLRQ QRVXSSO\ UHDGRXWVHWWLQJV 3)&VWDUWXS //&VWDUWXS RSHUDWLQJ DDD Fig 4. Start-up sequence and normal operation TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 7 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.1.2 Regulated supply (SUPREG pin) The voltage range on the SUPIC pin exceeds that of the maximum external MOSFETs gate-source voltage. So, the TEA19161T incorporates an integrated series stabilizer. The series stabilizer creates an accurate regulated voltage (Vintregd(SUPREG) = 11 V) at the buffer capacitor CSUPREG. The stabilized voltage is used to: * Supply the internal low-side LLC driver * Supply the internal high-side driver using external components * As a reference voltage for optional external circuits To ensure that the external MOSFETs receive sufficient gate drive, the voltage on the SUPREG pin must reach Vuvp(SUPREG) before the system starts switching. If the SUPREG voltage drops to below this undervoltage protection level, the system restarts. 7.1.3 High-side driver floating supply (SUPHS pin) External bootstrap buffer capacitor CSUPHS supplies the high-side driver. The bootstrap capacitor is connected between the high-side driver supply, the SUPHS pin, and the half-bridge node, HB. CSUPHS is charged from the SUPREG pin using an external diode DSUPHS (see Figure 27). Careful selection of the appropriate diode minimizes the voltage drop between the SUPREG and SUPHS pins, especially when large MOSFETs and high switching frequencies are used. A large voltage drop across the diode reduces the gate drive of the high-side MOSFET. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 8 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.2 System start-up Figure 5 shows the flow diagram corresponding with Figure 4. 9683,&9XYS 683,& RU 96835(*9XYS 6835(* 126833/< 9683,&!9VWDUW 683,& DQG 96835(*!9XYS 6835(* 3)&GLVDEOHG YLD616%2267 5($'287 6(77,1*6 DOOVHWWLQJVGHILQHG 683,&UHJXODWHG YLD683+9 3)&67$5783 9616%2267!9VWDUW 616%2267 //&67$5783 ,616)%!,UHJ 616)% 23(5$7,1* DDD Fig 5. TEA19161T LLC controller flow diagram When the SUPIC or SUPREG pins drop to below their stop levels, the TEA19161T enters the no supply state. It recharges the SUPIC and SUPREG pins to their start levels via the SUPHV pin. When the start levels are reached, measuring the external resistances on the SNSSET, SNSOUT, and GATELS pins initializes the settings. During the no supply and readout settings states, the SNSBOOST pin is pulled low, disabling the TEA19162T PFC. When the settings have been defined, the SNSBOOST pin is released and the PFC starts up. When the SNSBOOST reaches the minimum level Vstart(SNSBOOST), the LLC starts switching. When a small optocurrent is detected (ISNSFB < Ireg(SNSFB)), the output voltage is close to its regulation level. As the SUPIC pin must then be supplied via the primary auxiliary winding, charging via the SUPHV is disabled. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 9 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.3 LLC system regulation A typical resonant controller regulates the output power by adapting the operating frequency. 9ERRVW WUDIRPRGHO *$7(+6 /6 ' 9RXW /V /P )5(48(1&<&21752/ *$7(/6 IUHTXHQF\ ' IPD[ &U IPLQ 6835(* 9616)% 616)% 616%8567 9 DDD Fig 6. Resonant frequency controller If the power drops and so the voltage of the LLC converter exceeds the targeted regulation level (12 V or 19.5 V typical), the optocurrent increases and the voltage at the SNSFB decreases (see Figure 6). The resonant controller then increases the frequency according to its internal frequency control curve. Because of the higher frequency, the power to the output is reduced and the output voltage drops. If the output voltage becomes too low, the controller lowers the system frequency, increasing the output power. In this way, the system regulates the output power to the required level. As a small change in frequency gives a significant change in output power, frequency control has a high gain of the control loop. To increase the efficiency at low loads, most converters switch to burst mode as soon as the output power is below a minimum level. The burst mode level is mostly derived from the voltage on the SNSFB pin. For a frequency controlled resonant converter, it implies that the burst mode is entered at a certain frequency instead of at a certain load. A small variation of the resonant components then results in a significant variation in power level at which the burst mode is activated. In the TEA19161T, the control mechanism is different. The advantage is a constant gain of the control loop and a burst mode which is derived from the output power. The TEA19161T does not regulate the output power by adjusting the frequency but by the voltage across the primary capacitor. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 10 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply The input power (related to the output power) of a resonant converter can be calculated with Equation 1: P in = V boost I boost = V boost V Cr C r f sw (1) Equation 1 shows that the input power has a linear relationship with the capacitor voltage difference VCr. Figure 7 shows an alternative explanation of the linear relationship between the input power and the energy stored in the resonant capacitor. 9ERRVW 9RXW *$7(+6 /V +% /P *$7(/6 &U DDD Fig 7. Linear relationship between input power and energy stored in Cr When the high-side switch is on, a primary current is flowing through the transformer and resonant capacitor Cr as indicated by the red line. Half the energy the input delivers is transferred to the output. The other half charges resonant capacitor Cr. The voltage across the resonant capacitor increases. When the high-side switch is off and the low-side switch is on, the energy which is stored in resonant capacitor Cr is transferred to the output and its voltage decreases. In this way, the linear relationship between the increase of the resonant capacitor voltage and the output power can be seen. Although the TEA19161T uses the primary capacitor voltage as a regulation parameter, all application values, like the resonant inductances, resonant capacitor, and primary MOSFETs remain unchanged compared to a frequency controlled LLC converter. A secondary TL431 circuitry in combination with an optocoupler connected to the primary SNSFB pin continuously regulates the output voltage. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 11 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.3.1 Output power regulation loop Figure 8 shows the output power regulation loop of Vcap control as used by the TEA19161T. Figure 9 shows a corresponding timing diagram. 9ERRVW ,& *$7(+6 /6 WUDIRPRGHO ' 9RXW /V /P 9FDS&21752/ 9616&$3 *$7(/6 EXUVW ' 9KV 616&$3 9OV 616&$3 T V 9KV 616&$3 616&$3 TQ U ,EXUVW &U 9OV 616&$3 ,616)% ,616)% 616)% 9 DDD Fig 8. Regulation loop Vcap control ,ORDG ,UHJ 616)% $ ,616)% 9KV 616&$3 9616&$3 9OV 616&$3 W *$7(+6 *$7(/6 W Fig 9. W DDD Timing diagram of the regulation loop When the divided resonant capacitor voltage (VSNSCAP) exceeds the capacitor voltage high level (Vhs(SNSCAP)), the high-side MOSFET is switched off (see Figure 9 (t1). After a short delay, the low-side MOSFET is switched on. Because of the resonant current, the resonant capacitor voltage initially increases further but eventually drops. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 12 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply When the divided capacitor voltage (VSNSCAP) drops to below the capacitor voltage low level (Vls(SNSCAP)), the low-side MOSFET is switched off (see Figure 9 (t2)). After a short delay, the high-side MOSFET is switched on. Figure 9 shows that the switching frequency is a result of this switching behavior. In a frequency controlled system, the frequency is a control parameter and the output power is a result. The TEA19161T regulates the power and the frequency is a result. The difference between the high and low capacitor voltage level is a measure of the delivered output power. The value of the primary optocurrent, defined by the secondary TL431 circuitry, determines the difference between the high and low capacitor voltages. Figure 9 also shows the behavior at a transient. If the output load increases, the current pulled out of the SNSFB pin decreases. The result is that the TEA19161T increases the high-level capacitor voltage and lowers the low-level capacitor voltage. According to Equation 1, the output power increases and eventually the output voltage increases to its regulation level. To minimize no-load input power of the system, the primary current into the optocoupler is continuously regulated to 85 A (see Section 7.5). 7.3.2 Output voltage start-up The system controls the output power by regulating the primary VCr (see Section 7.3). When the system is in regulation and the output voltage is stabilized, a small change in VCr corresponds to a small change in the output current (see Equation 2). P out = V out I out V boost I boost = V Cr C r f sw V boost V Cr I out C r f sw V boost ------------V out (2) However, before start-up, when the output voltage is around zero, a small capacitor voltage increase (VCr) corresponds to a substantial output current increase. So, at start-up, the divided VCr voltage (VSNSCAP) is slowly increased from a minimum value to the regulation level. As a result, the system starts up at a higher frequency. The GATELS resistor sets the starting value of the VSNSCAP. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 13 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.4 Modes of operation Figure 10 shows the control curve between the output power and the voltage difference between the high and low capacitor voltage levels. 9616&$3&21752/ 9616&$3 9KV 616&$3 9616&$3 9OV 616&$3 EXUVW PRGH ORZSRZHU PRGH KLJKSRZHU PRGH 3RXW PD[ 3W OS ORZSRZHUSHULRG IOS PLQ WOS IU 3RXW 3RXW PD[ DDD Fig 10. TEA19161T control curve When the output power (Pout) is at its maximum, the low capacitor voltage level (Vls(SNSCAP)) is at its minimum and the high capacitor voltage (Vhs(SNSCAP)) is at its maximum level. According to Equation 1, the maximum VSNSCAP (Vhs(SNSCAP) Vls(SNSCAP)), which is the divided VCr voltage, corresponds to the maximum output power. When the output load decreases, the VSNSCAP voltage decreases. As a result, the output power decreases and the output voltage is regulated. This mode is called high-power mode. When the output power drops to below the transition level (Pt(lp)), the system enters the low-power mode. External components can set the applied Pt(lp) level (see Section 7.7.3). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 14 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply To compensate for the hold period, VSNSCAP is initially increased at entering the low-power mode (see Section 7.4.2). In low-power mode, the output power is initially regulated by adapting VSNSCAP, until it reaches a minimum. Then, the output power is regulated by lowering the duty cycle of the low-power mode with a fixed VSNSCAP until the period time of a low-power cycle reaches a maximum (1 / flp(min)). The system enters the burst mode (see Section 7.4.3). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 15 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.4.1 High-power mode In high-power mode, the system operates as described in Section 7.3.1. Figure 11 shows a flow diagram of the high-power mode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ig 11. High-power mode flow diagram TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 16 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply When the system is off, GATELS is on and GATEHS is off. The external bootstrap buffer capacitor (CSUPHS) is charged via the SUPREG pin and an external diode. The system remains in this state for at least the minimum on-time (ton(min)) of GATELS. Before entering the next state, one of the following conditions must be fulfilled: * * * * The VSNSCAP voltage drops to below the minimum VSNSCAP voltage (Vls(SNSCAP)) The measured current exceeds the OCP level (see Section 7.6.6) The system is close to capacitive mode (see Section 7.6.5) The maximum on-time (ton(max)), a protection that maximizes the time the high-side or low-side MOSFET is kept on, is exceeded. In the next state, to avoid false detection of the HB peak voltage, the system waits until the minimum non-overlap time (tno(min)) is exceeded. When it is exceeded, the system starts to detect the end (= peak voltage) of the HB node. When it detects the peak of the HB node and the measured resonant current is negative (or zero), it enters the next state. If the system does not detect a peak at the HB node, it also enters the next state when the maximum non-overlap time (tno(max)) is exceeded under the condition of a negative (or zero) resonant current. Finally, the third and fourth states (see Figure 11) describe the GATEHS and GATEHS to GATELS transition criteria which are the inverse of the first two states. 7.4.2 Low-power mode At low loads, the operating frequency of a resonant converter increases. As a result, the magnetization and switching losses increase. For this reason, the efficiency of a resonant converter drops at low loads. A newly introduced low-power mode ensures high efficiency at lower loads as well. When the output power drops to below the Pt(lp) level, the system enters the low-power mode (see Figure 10 and Figure 12). It continues switching for 3 half-cycles (low-side, high-side, low-side) with a fixed duty cycle of 67 %. To ensure a constant output power level, it increases the energy per cycle (Vhs(SNSCAP) Vls(SNSCAP)) at the same time. So 1/3 of the time the converter is in a "hold" period. The result is a 33 % magnetization and switching losses reduction. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 17 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply ,ORDG KLJKSRZHUPRGH ORZSRZHUPRGH 9KV 616&$3 9616&$3 9616&$3 9OV 616&$3 KDOIF\FOHV KROG SHULRG WOS ,' ,' DDD Fig 12. Timing diagram transition high-power mode to low-power mode As the system continuously tracks the primary capacitor voltage, it knows exactly when to enter the "hold" period. It can also continue again at exactly the correct voltage and current levels of the resonant converter. In this way, a "hold" period can be introduced which reduces the magnetization and switching losses without any additional losses. The currents ID1 and ID2 (see Figure 12) are the secondary currents through diodes D1 and D2 (see Figure 27). When in the low-power mode the output power is further reduced, the amount of energy per cycle (= VSNSCAP) is reduced and the duty cycle remains the same (see Figure 13). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 18 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply ,ORDG 9KV 616&$3 9616&$3 9OV 616&$3 ,' ,' DDD Fig 13. Low-power mode, lowering the energy per cycle (VSNSCAP) When, in low-power mode, the minimum energy per cycle is reached, the duty cycle regulates the output power (see Figure 14). Increasing the "hold" period lowers the duty cycle. ,ORDG 9KV 616&$3 9616&$3 9OV 616&$3 ,' ,' DDD Fig 14. Low-power mode, lowering the duty cycle To avoid audible noise, the system reduces the duty cycle until the frequency reaches flp(min) (23 kHz). If the output power is lowered further, the system enters the burst mode. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 19 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.4.3 Burst mode In burst mode, the system alternates between operating in low-power mode and an extended hold state (see Figure 15). Because of this additional extended hold period, the magnetization and switching losses are further reduced. So, the efficiency of the system is increased. Figure 15 shows that all operating frequencies are outside the audible area. The minimum low-power frequency is 23 kHz. Within a low-power period, the system is switching at the resonant frequency of the converter, which is typically between 50 kHz and 200 kHz. ORZSRZHU KROG ORZSRZHU KROG KROG ,616)% $ EXUVWRQ ,VHF WOS 7EXUVW DDD Fig 15. Burst mode The burst frequency (1 / tburst) is continuously regulated to a predefined value, which can be set externally to 200 Hz, 400 Hz, 800 Hz or 1600 Hz. Isec is the secondary current flowing through either diode D1 or D2 (see Figure 27). When the primary optocurrent (ISNSFB) drops to below 106 A, a new burst-on period is started. The end of the burst-on period depends on the calculated number of low-power cycles. The number of low-power cycles within a burst-on is continuously adjusted so that the burst period is at least the period defined by the setting (see Figure 16). ,ORDG ,616)% $ EXUVWRQ ,VHF 7EXUVW 7EXUVW W 7EXUVW W 7EXUVW W W DDD Fig 16. Burst mode: Regulating the number of low-power cycles The system continuously measures the burst period from the start of the previous burst-on period to a new burst-on period. At t1, the measured burst period (tburst) equals the required Tburst. So, the next number of low-power cycles equals the number of previous low-power cycles. At a constant output power, the system expects that when the next burst-on period has the same number of low-power cycles as the previous burst-on period, the burst period (tburst) remains constant. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 20 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply At a positive transient (t2), a new low-power cycle is started immediately to minimize the drop in output voltage. The measured time period, at time t2, is below the targeted burst period. The system increases the number of burst cycles. At t3, it measures the burst period again. In this example, the burst period is still below the targeted burst period. So, the system increases the number of low-power cycles again and again until the measured burst period equals the target burst period, which occurs at t4. 7.5 Optobias regulation In a typical application, the output voltage is sensed using a TL431 and connected to the SNSFB pin of the TEA19161T via an optocoupler (see Figure 27). Because of the behavior of the TL431, the current through the optocoupler is at the maximum level when the output power is at the minimum level. It is therefore one of the most critical parameters to achieve the required no-load input power. To achieve maximum efficiency at low load/no-load, the TEA19161T continuously regulates the optocurrent to a low level that is independent of the output load. A very low optocurrent reduces the transient response of the system, because of the parasitic capacitance at the optocoupler collector. So, the TEA19161T applies a fixed voltage at the SNSFB pin. It measures the current through the optocoupler which defines the required output power. Via an additional internal circuitry, which adds an offset to the required output power, the optocurrent is continuously (slowly) regulated to the Ireg(SNSFB) level (= 85 A). This level is independent of the output power. At a positive load transient, the optocurrent initially decreases (see Figure 9; ISNSFB). The TEA19161T immediately increases the VSNSCAP which again increases the output power. )(('%$&.&21752/ $' 997 N 3 9616&$3 9 616)% DDD Fig 17. Optobias regulation Figure 17 shows that when the optocurrent decreases, the internal voltage across the 12 k resistor drops to below the targeted level of 1020 mV (= 85 A 12 k). The TEA19161T then slowly increases an additional offset at the power level (P). It continues to increase the additional offset until the optocurrent reaches the target of 85 A. At a negative transient, the additional offset to the power level is decreased. As a result, the output voltage increases which again increases the optocurrent. In this way, the optocurrent is continuously regulated to the Ireg(SNSFB) level (see Figure 9). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 21 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply The behavior of the internal circuitry connected to the SNSFB pin is the same as the behavior of the traditional circuitry. The fixed voltage at the SNSFB pin and the continuous regulation of the optocurrent level does not influence the regulation level. The advantage, however, is a reduction in no-load input power and an optimization of the transient response. When the system operates in low-power mode at the minimum energy per cycle and at minimum duty cycle, it can no longer reduce the optocurrent level to the Ireg(SNSFB) target (85 A). If the output power decreases further and the optocurrent increases to above the level of Istart(burst) (106 A), the burst mode is triggered. When the output power drops to below this level again, a new burst cycle is started (see Figure 15 and Figure 16). 7.6 Protections Table 3 gives an overview of the available protections. Table 3. Protections Protection Description Action PFC UVP SUPIC/SUPREG undervoltage protection SUPIC/SUPREG pins LLC = off; recharge via SUPHV; restart when VSUPIC > Vstart(SUPIC) and VSUPREG > Vstart(SUPREG) off UVP SUPHS undervoltage protection SUPHS pin GATEHS = off UVP SNSBOOST undervoltage protection boost LLC = off; restart when VSNSBOOST > Vstart(SNSBOOST) OVP output overvoltage protection output latched after 5 consecutive cycles[1][2] CMR capacitive mode regulation system ensures that mode of operation is inductive OCP overcurrent protection switch off cycle-by-cycle; After 5 consecutive cycles, it follows the OPP setting.[2] off OTP overtemperature protection latched[2] off overpower protection latched[2]/safe OPP [1] Can be longer due to the sharing of the internal ADC converter. [2] Latched implies that the system only restarts after a mains disconnection. [3] Can be set by external components. restart[3] off off When the system is in a latched or safe restart protection, the SUPIC voltage is regulated to its start level via the SUPHV pin. 7.6.1 Undervoltage protection SUPIC/SUPREG When the voltage on the SUPIC pin or the SUPREG pin is below its undervoltage level Vuvp(SUPIC) / Vuvp(SUPREG), the LLC converter stops switching. The capacitors at the SUPIC and SUPREG pins are recharged via the SUPHV pin (see Figure 5). The SNSBOOST pin is pulled low, disabling the PFC. When the supply voltages exceed their start levels, the system restarts. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 22 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.6.2 Undervoltage protection SUPHS To ensure a minimum drive voltage at the high-side driver output (GATEHS), this driver is kept off when its voltage is below the minimum level (VSUPHS < Vrst(SUPHS)). 7.6.3 Undervoltage protection boost The PFC output voltage is measured via a resistive divider connected to the SNSBOOST pin. The voltage at the SNSBOOST pin must exceed the start level (VSNSBOOST > Vstart(SNSBOOST)) before the system is allowed to start switching. When the system is operating and the voltage at the SNSBOOST pin drops to below the minimum level (VSNSBOOST < Vuvp(SNSBOOST)), the LLC converter stops switching. When it exceeds the start level, it restarts. 7.6.4 Overvoltage protection When the voltage at the SNSOUT pin exceeds the Vovp(SNSOUT) level for at least 5 consecutive switching cycles, the OVP protection is triggered. The voltage at the SNSOUT pin is internally measured via an ADC converter. As the same ADC converter toggles between measuring the SNSOUT and SNSBOOST pins (see Figure 1), there is an additional delay before the OVP is triggered. OVP is a latched protection. The PFC is disabled via the SNSBOOST pin. 7.6.5 Capacitive Mode Regulation (CMR) The TEA19161T has a Capacitive Mode Regulation (CMR) which ensures that the system is always operating in inductive mode and avoids operation in capacitive mode. At lower input voltage or higher output power and depending on the resonant design, the resonant current can already approach zero before the capacitor voltage reaches the regulation level. When the resonant current has changed polarity before the switches are turned off and the other switch is turned on, hard switching occurs. This event is called capacitive mode. To avoid that the system operates in capacitive mode, the system also switches off the high-side/low-side switch when the resonant current approaches zero. Figure 18 shows the signals that occur when a resonant converter is switching in CMR mode. At t1 (and also at t3), the low-side switch is on while the resonant current approaches zero before VSNSCAP reaches Vls(SNSCAP). At t2, the resonant current is also close to changing polarity while the divided capacitor voltage (VSNSCAP) has not reached the Vhs(SNSCAP) level yet. To avoid a turn-off of the high-side switch at a negative current or the low-side at a positive current, the system also turns off the high-side/low-side switch when the primary current approaches zero. So at t2, the high-side switch is turned off because the primary current is close to zero. At t3 (and also at t1), the low-side switch is turned off, although VSNSCAP did not reach the regulation level (Vls(SNSCAP)) yet. The primary current is measured via an external sense resistor connected to the SNSCUR pin. The capacitive mode protection levels are Vreg(capm) (100 mV and +100 mV, respectively). In this mode, the amount of output power is reduced and the output voltage decreases. The TEA19161T does not enter a so-called "capacitive mode protection", but avoids this mode of operation. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 23 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply *$7(+6 *$7(/6 +% 9KV 616&$3 9616&$3 9OV 616&$3 ,SULP 9UHJ FDSP 9UHJ FDSP W W W W DDD Fig 18. Near capacitive mode switching 7.6.6 Overcurrent protection The system measures the primary current continuously via a sense resistor connected to the SNSCUR pin. If the measured voltage exceeds the overcurrent level (Vocp), the corresponding switch (GATELS/GATEHS) is turned off, but the system continuous switching. In this way, the primary current is limited to the OCP level. If the OCP level is exceeded for 5 consecutive cycles (GATELS and/or GATEHS), the system stops switching and enters the latched OCP protection mode. The PFC is disabled via the SNSBOOST pin. 7.6.7 Overtemperature protection When the internal junction temperature exceeds the Totp level, the overtemperature protection is triggered. OTP is a latched protection which also disables the PFC. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 24 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.6.8 Overpower protection 9616&$3&21752/ 9KV 616&$3 9616&$3 9RSS 616&$3 9WK PD[ 616&$3 EXUVWPRGH 9OV 616&$3 ORZSRZHUPRGH VWDUWLQJLQWHUQDO FRXQWHUPV 3W OS 3RXW DDD Fig 19. TEA19161T overpower The external capacitive/resistive divider connected to the SNSCAP pin must be chosen such that: * The voltage difference between Vhs(SNSCAP) and Vls(SNSCAP) equals Vopp(SNSCAP) * The voltage difference between Vhs(SNSCAP) and Vls(SNSCAP) occurs at 125 % of the maximum output power or at 175 %, depending on the settings When the VSNSCAP (Vhs(SNSCAP) Vls(SNSCAP)) exceeds the Vopp(SNSCAP) voltage difference, an internal counter is started. When this counter exceeds td(opp) (50 ms/200 ms), the system enters a latched/safe restart protection as defined by the external settings. The voltage difference between Vhs(SNSCAP) and Vls(SNSCAP) is also limited to Vth(max)SNSCAP, which then corresponds to an output power of 150 % or 200 %, depending on the settings (see Figure 19). If the output of the LLC converter requires additional power, the output voltage drops as the power delivered by the LLC converter is limited to 150 % or 200 %. An additional option is to disable the overpower counter, using the external settings. In this way, the overpower rating can be used as an extension of the typical power level. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 25 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.7 External settings Before the system starts switching, it reads the external settings. Using specific resistor values at the GATELS, SNSSET, and SNSOUT pins, several internal settings can be defined. 7.7.1 Burst period Figure 20 shows how the internal regulated burst frequency can be set using the external resistor connected to the SNSOUT pin. 5616287 616287 5616287 DDD Fig 20. External setting of the burst frequency Table 4. External setting of the burst frequency RSNSOUT1 Burst frequency 22 k 200 Hz 15 k 400 Hz 10 k 800 Hz 6.8 k 1600 Hz The absolute value of the resistor connected between the SNSOUT pin and ground (RSNSOUT1) defines the burst frequency. An accurate resistor of 1 % according to Table 4 is required. The OVP level can be set using resistor RSNSOUT2. A low burst frequency is best for minimum audible noise. However, a high burst frequency minimizes the output voltage ripple. 7.7.2 General settings Variables on the OPP function can be set using resistor RSNSSET1 connected to the SNSSET pin (see Figure 21). ,& 6166(7 56166(7 56166(7 &6166(7 DDD Fig 21. External setting of the SNSSET pin TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 26 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 5. General settings RSNSSET1 (k) Power capability level (%) OPP timer level (%) 46.4 200 infinite 53.6 200 61.9 200 < 10 End of power good timer (ms) OPP timer (ms) Protection 175 190 200 1 s restart 175 45 50 1 s restart no start-up 71.5 150 125 190 200 1 s restart 82.5 150 125 45 50 1 s restart 95.3 200 175 190 200 latched 110 200 175 45 50 latched 127 150 125 190 200 latched 147 150 125 45 50 latched When the measured value of RSNSSET1 < 10 k, the system assumes a shorted pin to ground and the start-up is inhibited. At a value of 46.4 K, the system can of continuously delivering the maximum power of 200 %. The output power level at which the overpower timer is started can be set to 125 % or 175 %. Two corresponding timer values can be selected, 50 ms or 200 ms. Finally, the value of RSNSSET1 (see Table 5) can set the behavior of the overpower function (either a 1 s restart or latched). During this protection period, the SUPIC is regulated at its Vstart(SUPIC) level. 7.7.3 Low-power mode/burst mode transition levels To ensure the best efficiency, the system must enter the low-power mode and the burst mode at high power levels. However, to ensure the best output ripple, these modes must be entered at low-power levels. To choose the optimum level for a specific application, the power transition levels at which the system enters the low-power mode and the burst mode can be set externally. Resistor RSNSSET2 defines the power levels at which the system enters the low-power mode and the burst mode. Table 6 gives an overview. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 27 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 6. External setting of the high-power/low-power and low-power/burst transition levels RSNSSET2 (k) High-power => low-power (%)[1] Burst mode[1] 200 Hz (%) 400 Hz (%) 800 Hz (%) 1600 Hz (%) 1 25 9 9 9 9 6.8 25 12 12 12 12 15 37.5 9 9 9 10 27 37.5 12 12 12 13 47 50 9 10 11 12 82 50 12 13 15 17 180 62.5 9 10 12 14 open 62.5 12 15 17.5 20 [1] The values in this table are including the additional shift due to the internal (tPD(SNSCAP)) delay and a typical external delay of 150 ns and 300 ns, respectively. When an external R + C network compensates these delays, the levels in Table 6 can be lowered. The power level at which the system enters the burst mode also depends on the defined burst period. In this way, the optimum between efficiency and output voltage ripple can be chosen. 7.8 Power good function The TEA19161T provides a power good function via the SNSSET pin. At initialization, the TEA19161T measures the resistors connected to the SNSSET pin to set internal variables. After that, the pin is used for the power good function. 6835(* ' 9RXW 6166(7 ,& SRZHUJRRG ' DDD a. Primary side DDD b. Secondary side Fig 22. Power good function After the system has read the external settings (see Figure 5), the SNSSET output is active high, enabling an external MOSFET. A secondary power good signal can be pulled low using an external optocoupler. When the system enters the operating state (see Figure 5), the SNSSET output is pulled low and the external power good signal becomes active high. Any required delay can be achieved via an external R/C network. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 28 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply At low power good, the SNSSET output becomes active high when: * The voltage on the SNSBOOST pin drops to below Vdet(SNSBOOST) (1.95 V) * The OPP counter is at a value indicated in Table 5. In this way, the secondary power good signal is pulled low at 5 ms or 10 ms before the output is disabled. When the system enters protection mode (OVP, OCP, UVP or OTP), it pulls low the SNSSET pin and stops switching immediately. 7.9 PFC/LLC communication protocol The TEA19161T is designed to cooperate with the TEA19162T (PFC) in one system. The TEA19161T and TEA19162T can be seen as a combination, split up into two packages. All required functionality between the two controllers is arranged via the combined SUPIC and SNSBOOST pins. 7.9.1 Start-up To ensure that at start-up the TEA19161T and TEA19162T are enabled at the same time, the TEA19161T (LLC) pulls down the SNSBOOST pin to below the SNSBOOST short protection level of the PFC. The TEA19161T disables the TEA19162T (PFC) (see Figure 23) until the system enters the PFC start-up phase (see Figure 5 and Figure 23). The SUPIC start levels and stop levels of the TEA19162T (PFC) are below the SUPIC start levels and stop levels of the TEA19161T (LLC). When the SUPIC exceeds the start level of the TEA19161T, both controllers are enabled. In this way, both controllers are enabled/disabled at the same SUPIC start and stop levels. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 29 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 683,& 3)& //& 9VWDUW 683,& 9 9VWDUW K\V 683,& 9 9XYS 683,& 9 9VWDUW 683,& 9 9XYS 683,& 9 9UVW 683,& 9 W W W W 9ERRVW 9UHJ 616%2267 9 9VWDUW 616%2267 9 616%2267 9VKRUW 616%2267 9 WG VWDUW W 3)& 89/2 RII ZDLW RQ W 89/2 //& 683,&UHJXODWLRQ RQ 9RXW DDD Fig 23. Start-up of the PFC and LLC When the LLC reaches a minimum supply voltage level (Vrst(SUPIC); t1), the LLC pulls down the SNSBOOST pin to disable the PFC. At t2, the SUPIC reaches the start level of the PFC converter. However, as the LLC pulls low the SNSBOOST voltage to < the PFC short protection level, the PFC is still off. When at t3 the SUPIC reaches the start level of the LLC, after the LLC has read out the external settings, the SNSBOOST voltage is released. It increases because of the connected resistive divider which is connected to the PFC boost voltage. To ensure that the SNSBOOST voltage is a representative of the Vboost voltage before the system actually starts to switch, an additional delay (until t4) is built into the PFC controller before it starts. When at t5 the SNSBOOST voltage reaches the start level of the LLC, the LLC converter starts to switch. At t6, the SUPIC is supplied via the primary auxiliary winding. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 30 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 7.9.2 Protection When a protection is triggered in either the PFC or LLC, it may also disable the other converter. For example, if an OVP is detected at the LLC, both converters are latched. Also, at initial start-up, the PFC disables the LLC converter until the mains voltage detects the brownin level. The PFC can disable the LLC converter by pulling down the SNSBOOST pin to below the Vuvp(SNSBOOST) level of the LLC converter. The LLC can disable the PFC converter by pulling down the SNSBOOST pin to below the short protection level of the PFC converter SNSBOOST pin. Table 3 in Section 7.6 gives an overview of protections in the LLC converter. It shows which protections also disable the PFC. 683,& 3)& //& 9VWDUW 683,& 9 9VWDUW K\V 683,& 9 9XYS 683,& 9 9VWDUW 683,& 9 9XYS 683,& 9 9UVW 683,& 9 W W W W PDLQV EURZQLQ 9UHJ 616%2267 9 9VWDUW 616%2267 9 616%2267 W 9VKRUW 616%2267 9 W WG VWDUW 3)& 893 EURZQRXW RQ ZDLW W 893 RII //& RQ 683,&UHJXODWLRQ 293 9RXW W W 616287 !F\FOHV 9RYS 616287 9 DDD Fig 24. System protection TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 31 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply The start-up period up to t3 is identical in Figure 23 and Figure 24. At t3, the LLC converter releases the pull-down of the SNSBOOST pin. However, as the mains voltage is below the brownin level, the PFC converter pulls low the SNSBOOST pin. When the mains voltage exceeds the brownin level (t4), the SNSBOOST pin is released and increases because of the resistive divider connected between the PFC boost voltage and the SNSBOOST pin. To allow some external capacitance on the SNSBOOST pin, the PFC converter waits until the SNSBOOST voltage is stabilized. At t5, the PFC converter starts to switch. At t6, the LLC converter also starts to switch, as the SNSBOOST voltage reaches the Vstart(SNSBOOST) of the LLC converter. At t7, the primary auxiliary winding takes over the supply of the SUPIC pin. At t8, the LLC detects an OVP at the SNSOUT pin. After at least 5 consecutive OVP cycles (t9), the LLC stops switching and pulls down the SNSBOOST pin. As a result, the PFC also stops switching. When either the PFC or LLC is in protection, the SUPIC pin is regulated to the Vstart(SUPIC) via the SUPHV pin as soon as it drops below the Vstart(SUPIC) level. 7.9.3 Fast latch reset The SUPIC pin is regulated to the Vstart(SUPIC) level when a (latched) protection is triggered. So, it can remain in this protection mode until the capacitor at the PFC output, which the SUPHV is connected to, is discharged. Hence, it may remain in protection mode for a long time after the mains is disconnected. When protection modes are tested at mass-production, a long reset time is not acceptable in most cases. So, a fast latch reset function is built into the PFC and the LLC. When the mains is initially disconnected and then reconnected, all protections the PFC or the LLC initiated are released again. TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 32 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 683,& 3)& //& 9VWDUW 683,& 9 9VWDUW K\V 683,& 9 WG PDLQV ER PDLQV EURZQLQ EURZQRXW W 9UHJ 616%2267 9 9VWDUW 616%2267 9 9SX UVW 616%2267 9 9XYS 616%2267 9 9616%2267 9VFS VWRS 9 WG VWDUW W 3)& RII ZDLW EURZQRXW RQ W //& 893616%2267 SURWHFWLRQ 9RXW RQ W DDD Fig 25. Fast latch reset Before t1, the LLC is in a (latched) protection and pulls down the SNSBOOST pin, which also disables the PFC. When the mains voltage drops to below the brownout level for a minimum period of td(mains)bo, the PFC enters the brownout protection mode. When the mains voltage increases again to > the brownin level (t2) in the brownout protection mode, the PFC pulls up the SNSBOOST voltage until it reaches the Vuvp(SNSBOOST) level of the LLC converter. The LLC converter then releases all protection modes and waits until the SNSBOOST pin exceeds its start level (Vstart(SNSBOOST)). After a waiting time, the PFC converter starts (t3), followed by a start-up of the LLC converter (t4). 7.9.4 PFC burst mode When the LLC operates in burst mode and the duty cycle of the burst is below 50 % for at least 8 consecutive burst periods, the TEA19161T (LLC) sets the TEA19162T (PFC) in burst mode as well. The corresponding output power level is then 50 % of the power level at which the LLC enters the burst mode (see Table 6). When the output power exceeds 75 % of the power level at which the LLC enters the burst mode (see Table 6), the PFC burst is disabled again. When the PFC burst is enabled, an additional current out of the SNSBOOST pin stops the PFC from switching via a soft stop, so the audible noise is minimized (see Figure 26). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 33 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 3)& //& ,RII EXUVW $ *0$03/,),(5 ,RQ VWRS VRIW $ 3)&EXUVWPRGH 9616%2267!9 T V 9 VRIWVWRS 616%2267 U 9RII EXUVW 3)&&203 0$; 9$/8( N 9 5(6(7 9 V '(/$< 293 9 DDD a. Block diagram 3)& //& 21 2)) 21 2)) W 9616%2267 9GHW + 616%2267 9 ,RII EXUVW 9RII EXUVW P9 9GHW / 616%2267 9 9RYS VWRS 9 9UHJ 616%2267 9 9RQ EXUVW PD[ 9 W W 9FODPS 3)&&203 9 W 9WRQ]HUR 3)&&203 9 W W 9*$7(3)& DDD b. Timing diagram Fig 26. PFC burst mode At t1, the current out of the LLC SNSBOOST pin (Ioff(burst)) is activated and the voltage on the SNSBOOST pin increases. When an external 100 k resistor (RSNSBOOST) is used between the SNSBOOST pin and GND pin (see Figure 27), the SNSBOOST voltage increase is approximately 640 mV (= Ioff(burst) * RSNSBOOST). Because of this increase, the SNSBOOST voltage is between the Vdet(L)SNSBOOST and Vdet(H)SNSBOOST levels of the PFC (t2), so the soft stop of the PFC converter is started. At the end of the soft stop, the PFC enters the energy safe state and stops switching (t3). Because of the continuous operation of the LLC converter, even when the PFC is stopped, the PFC output capacitor is discharged. When the PFC boost capacitor is discharged so much that the voltage on the SNSBOOST pin has dropped 75 mV (Voff(burst); t4), the internal current source in the LLC converter is switched off. Because of the negative voltage drop at the SNSBOOST pin, the PFC starts switching again. When VSNSBOOST exceeds the LLC Von(burst)max level (2.37 V) again, the internal current source is reactivated and the PFC stops switching again (t1). TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 34 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 8. Limiting values Table 7. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol Parameter Conditions Min Max Unit VSUPHV voltage on pin SUPHV maximum during mains surge; not repetitive 0.4 +700 V VSUPHS voltage on pin SUPHS VHB VHB + 14 V VHB voltage on pin HB maximum during mains surge; not repetitive 3 +700 V t < 1 s 14 - V Voltages VSUPIC voltage on pin SUPIC 0.4 +36 V VSUPREG voltage on pin SUPREG 0.4 +12 V VGATEHS voltage on pin GATEHS VHB 0.4 VSUPHS + 0.4 V VGATELS voltage on pin GATELS 0.4 VSUPREG + 0.4 V VSNSFB voltage on pin SNSFB 0.4 +12 V VSNSOUT voltage on pin SNSOUT 0.4 +12 V VSNSSET voltage on pin SNSSET 0.4 +12 V VSNSCUR voltage on pin SNSCUR 0.4 +12 V VSNSCAP voltage on pin SNSCAP 0.4 +12 V VSNSBOOST voltage on pin SNSBOOST 0.4 +12 V current on pin SUPHV - 20 mA - 0.7 W Currents ISUPHV General Tamb < 75 C Ptot total power dissipation Tstg storage temperature 55 +150 C Tj junction temperature 40 +150 C 100 +100 mA pins SUPHV, SUPHS, GATEHS, and HB 1000 +1000 V other pins 2000 +2000 V 500 +500 V Latch-up Ilu latch-up current all pins; according to JEDEC: Standard 78D electrostatic discharge voltage human body model ESD VESD charged device model; all pins TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 35 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 9. Thermal characteristics Table 8. Thermal characteristics Symbol Parameter Conditions Typ Unit Rth(j-a) thermal resistance from junction to ambient In free air; JEDEC test board 107 K/W Rth(j-c) thermal resistance from junction to case In free air, JEDEC test board 60 K/W 10. Characteristics Table 9. Characteristics Tamb = 25 C; VSUPIC = 19.5 V; all voltages are measured with respect to GND; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Ilim(SUPHV) current limit on pin SUPHV VSUPIC < Vrst(SUPIC) 0.5 0.75 1.0 mA Ioff(SUPHV) off-state current on pin SUPHV VSUPIC = 15 V - 0.5 0.9 A VI(SUPHV-SUPIC) input voltage difference ISUPHV = 20 mA between pin SUPHV and pin SUPIC - 7 - V Vstart(SUPIC) start voltage on pin SUPIC 18.3 19.1 19.8 V Vstart(hys)SUPIC start voltage hysteresis on pin SUPIC - 0.7 - V Vlow(hys)SUPIC low voltage hysteresis on pin SUPIC - 0.9 - V Vlow(SUPIC) low voltage on pin SUPIC - 14.0 - V Vuvp(SUPIC) undervoltage protection voltage on pin SUPIC 12.7 13.2 13.7 V Vrst(SUPIC) reset voltage on pin SUPIC - 3.5 - V ICC(SUPIC) supply current on pin SUPIC operating mode; fHB = 100 kHz; GATEHS/GATELS open; ISNSFB = 85 A; ISNSCAP = 100 A - 5.6 - mA latched protection; ISNSFB = 0 A; ISNSCAP = 100 A 2.3 3.0 3.7 mA burst mode; ISNSFB = 106 A; ISNSCAP = 100 A - 0.7 - mA SUPHV pin SUPIC pin Vuvp(SUPIC) = 13.3 V; tracks with Vuvp(SUPIC) SUPREG pin Vintregd(SUPREG) internal regulated voltage on VSUPIC > 13.8 V; pin SUPREG ISUPREG = 50 mA 10.6 11.0 11.4 V Vreg(acc)SUPREG regulator voltage accuracy on pin SUPREG 150 100 50 mV Ilim(SUPREG) current limit on pin SUPREG VSUPIC = 19.5 V 44 37 30 mA TEA19161T Product data sheet VSUPIC > 13.8 V; 10 A < ISUPREG < 20 mA All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 36 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 9. Characteristics ...continued Tamb = 25 C; VSUPIC = 19.5 V; all voltages are measured with respect to GND; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit Vuvp(SUPREG) undervoltage protection voltage on pin SUPREG 8.6 9.0 9.4 V - 2.50 - V 245 210 175 A Vhs(SNSCAP) Vls(SNSCAP); Pout = 200 %; VSNSBOOST = 2.5 V - 1.92 - V Vhs(SNSCAP) Vls(SNSCAP); Pout = 200 %; VSNSBOOST < 2.0 V 2.85 3.00 3.15 V overpower protection voltage difference on pin SNSCAP Vhs(SNSCAP) Vls(SNSCAP); Pout = 150 %; VSNSBOOST = 2.5 V - 1.44 - V Vhs(SNSCAP) Vls(SNSCAP); Pout = 150 %; VSNSBOOST = 2.1 V - 2.24 - V tPD(SNSCAP) propagation delay on pin SNSCAP from crossing Vls(SNSCAP)/Vhs(SNSCAP) level to GATELS/GATEHS switch-off - 150 - ns td(opp) overpower protection delay time See Table 5 for related RSNSSET1 40 50 60 ms See Table 5 for related RSNSSET1 160 170 180 ms restart delay time 0.8 1.0 1.2 s Vbias(SNSCUR) bias voltage on pin SNSCUR 2.4 2.5 2.6 V RO(SNSCUR) output resistance on pin SNSCUR - 60 - k Vocp overcurrent protection voltage positive level; VSNSCUR Vbias(SNSCUR) 1.35 1.50 1.65 V negative level; VSNSCUR Vbias(SNSCUR) 1.65 1.50 1.35 V positive level; VSNSCUR Vbias(SNSCUR) 85 100 115 mV negative level; VSNSCUR Vbias(SNSCUR) 115 100 85 mV detected as 0 - 13 - mV detected as 0 - 13 - mV SNSCAP pin VAV(regd)SNSCAP regulated average voltage on pin SNSCAP regulated average of Vhs(SNSCAP) and Vls(SNSCAP) Ibias(max)SNSCAP maximum bias current on pin SNSCAP Vth(max)SNSCAP maximum threshold voltage difference on pin SNSCAP Overpower protection Vopp(SNSCAP) td(restart) SNSCUR pin Vreg(capm) Vdet(zero) capacitive mode regulation voltage zero detection voltage SNSBOOST pin Vstart(SNSBOOST) start voltage on pin SNSBOOST 2.2 2.3 2.4 V Vuvp(SNSBOOST) undervoltage protection voltage on pin SNSBOOST 1.5 1.6 1.7 V Vdet(SNSBOOST) detection voltage on pin SNSBOOST - 1.95 - V TEA19161T Product data sheet when below power good = LOW All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 37 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 9. Characteristics ...continued Tamb = 25 C; VSUPIC = 19.5 V; all voltages are measured with respect to GND; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit % PFC burst mode controller en(burst) burst mode enable duty cycle enable of PFC burst mode; duty cycle of LLC burst mode - 50 - Ncy(en)burst burst mode enable number of cycles enable of PFC burst mode; cycles of LLC burst mode - 8 - dis(burst) burst mode disable duty cycle disable of PFC burst mode; duty cycle of LLC burst mode - 75 - % Vpu(SNSBOOST) pull-up voltage on pin SNSBOOST to enter PFC burst mode off-state - 2.95 - V during PFC burst mode off-state Ioff(burst) burst mode off-state current 7.1 6.4 5.7 A Voff(burst) burst mode off-state voltage during PFC burst mode off-state; difference between peak voltage and end of off-state - 75 - mV Von(burst)max maximum burst mode on-state voltage during PFC burst mode on-state 2.29 2.37 2.45 V tto(det)on(burst) burst mode on-state detection time-out time during PFC burst mode on-state 3.7 4.0 4.3 ms PFC protection controller Rpd(SNSBOOST) pull-down resistance on pin SNSBOOST at protection activation - 550 - Ipd(SNSBOOST) pull-down current on pin SNSBOOST during active protection 94 110 127 A Iprot(SNSBOOST) protection current on pin SNSBOOST - 60 - nA Vovp(SNSOUT) overvoltage protection voltage on pin SNSOUT 3.36 3.50 3.64 V Iprot(SNSOUT) protection current on pin SNSOUT for open pin - 60 - nA bias voltage on pin SNSFB ISNSFB = 85 A 2.2 2.5 2.8 V Ireg(SNSFB) regulation current on pin SNSFB Istart(burst) = 106 A; tracks with Istart(burst) - 85 - A Ireg(max)SNSFB maximum regulation current Istart(burst) = 106 A; on pin SNSFB tracks with Istart(burst) - 310 - A Ireg(min)SNSFB minimum regulation current on pin SNSFB Istart(burst) = 106 A; tracks with Istart(burst) - 63 - A Istart(burst) burst mode start current LLC burst mode 123 106 89 A Istop(burst) burst mode stop current LLC burst mode - 200 - A SNSOUT pin SNSFB pin Vbias(SNSFB) Optobias regulator Burst mode regulator TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 38 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 9. Characteristics ...continued Tamb = 25 C; VSUPIC = 19.5 V; all voltages are measured with respect to GND; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit GATELS and GATEHS pins Isource(GATEHS) source current on pin GATEHS VGATEHS VHB = 4 V - 340 - mA Isource(GATELS) source current on pin GATELS VGATELS VGND = 4 V - 340 - mA Isink(GATEHS) sink current on pin GATEHS VGATEHS VHB = 2 V Isink(GATELS) - 580 - mA VGATEHS VHB = 11 V - 2 - A sink current on pin GATELS VGATELS VGND = 2 V - 580 - mA VGATELS VGND =11 V - 2 - A Vrst(SUPHS) reset voltage on pin SUPHS Vrst(hys)SUPHS hysteresis of reset voltage on pin SUPHS ton(min) minimum on-time ton(max) maximum on-time tsweep sweep time > Vrst(SUPHS) 6.4 7 7.6 V - 0.6 - V - 0.83 - s 14.8 17.4 20.0 s 1 12 14 ms 20 23 26 kHz RSNSOUT1 = 22 k 170 200 230 Hz RSNSOUT1 = 15 k 340 400 460 Hz RSNSOUT1 = 10 k 680 800 920 Hz RSNSOUT1 = 6.8 k 1360 1600 1840 Hz frequency; at start-up Low-power mode regulator flp(min) minimum low-power mode frequency Burst mode regulator fburst(max) maximum burst mode frequency Power good characteristics (pin SNSSET) VOH(SNSSET) HIGH-level output voltage on pin SNSSET ISNSSET = 100 A; power good = LOW - 4 - V IOH(SNSSET) HIGH-level output current on pin SNSSET VSNSSET = 3 V; power good = LOW 11 8 5 mA IOL(SNSSET) LOW-level output current on VSNSSET = 0.5 V; pin SNSSET power good = HIGH 8 11 14 mA td(H)SNSSET HIGH-level delay time on pin SNSSET See Table 5 for related RSNSSET1 35 45 55 ms See Table 5 for related RSNSSET1 150 190 230 ms Settings sensor (SNSOUT, SNSSET, and GATELS pins) IO(SNSOUT) output current on pin SNSOUT during RSNSOUT1 measurement - 171 - A IO(SNSSET) output current on pin SNSSET during RSNSSET measurement - 26.8 - A VO(GATELS-SUPREG) output voltage difference between pin GATELS and pin SUPREG during RGATELS measurement - 1.25 - V TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 39 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Table 9. Characteristics ...continued Tamb = 25 C; VSUPIC = 19.5 V; all voltages are measured with respect to GND; currents are positive when flowing into the IC; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Unit HB pin (dV/dt)tno(min) minimum non-overlap time rate of change of voltage - - 120 V/s tno(min) minimum non-overlap time - 200 - ns tno(max) maximum non-overlap time - 1.1 - s 130 140 150 C Overtemperature protection Totp TEA19161T Product data sheet overtemperature protection trip All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 40 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 11. Application information 9ERRVW '683+6 5683+9 &6835(* &683+6 6835(* 683+9 683+6 *$7(+6 6 ' 9RXW /V +% SRZHUJRRG /P 616%2267 *$7(/6 6 ' 616&$3 7($ 6835(* 616&85 &U 683,& 6166(7 &683,& 616287 *1' 616)% DDD Fig 27. TEA19161T application diagram TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 41 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 12. Package outline 62SODVWLFVPDOORXWOLQHSDFNDJHOHDGVERG\ZLGWKPPERG\WKLFNQHVVPP ' ( 627 $ ; F \ +( Y 0 $ = $ $ $ $ SLQLQGH[ /S / H Z 0 ES GHWDLO; PP VFDOH ',0(16,216 LQFKGLPHQVLRQVDUHGHULYHGIURPWKHRULJLQDOPPGLPHQVLRQV 81,7 $ PD[ $ $ $ ES F ' ( H +( / /S Y Z \ = PP LQFKHV R R 1RWH 3ODVWLFRUPHWDOSURWUXVLRQVRIPP LQFK PD[LPXPSHUVLGHDUHQRWLQFOXGHG 5()(5(1&(6 287/,1( 9(56,21 ,(& -('(& 627 06$& -(,7$ (8523($1 352-(&7,21 ,668('$7( Fig 28. Package outline SOT109-3 (SO16) TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 42 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 13. Revision history Table 10. Revision history Document ID Release date Data sheet status Change notice Supersedes TEA19161T v.1 20160310 Product data sheet - - TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 43 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 14. Legal information 14.1 Data sheet status Document status[1][2] Product status[3] Definition Objective [short] data sheet Development This document contains data from the objective specification for product development. Preliminary [short] data sheet Qualification This document contains data from the preliminary specification. Product [short] data sheet Production This document contains the product specification. [1] Please consult the most recently issued document before initiating or completing a design. [2] The term `short data sheet' is explained in section "Definitions". [3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com. 14.2 Definitions Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. Product specification -- The information and data provided in a Product data sheet shall define the specification of the product as agreed between NXP Semiconductors and its customer, unless NXP Semiconductors and customer have explicitly agreed otherwise in writing. In no event however, shall an agreement be valid in which the NXP Semiconductors product is deemed to offer functions and qualities beyond those described in the Product data sheet. 14.3 Disclaimers Limited warranty and liability -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. NXP Semiconductors takes no responsibility for the content in this document if provided by an information source outside of NXP Semiconductors. In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Notwithstanding any damages that customer might incur for any reason whatsoever, NXP Semiconductors' aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the Terms and conditions of commercial sale of NXP Semiconductors. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. TEA19161T Product data sheet Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors and its suppliers accept no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Customers are responsible for the design and operation of their applications and products using NXP Semiconductors products, and NXP Semiconductors accepts no liability for any assistance with applications or customer product design. It is customer's sole responsibility to determine whether the NXP Semiconductors product is suitable and fit for the customer's applications and products planned, as well as for the planned application and use of customer's third party customer(s). Customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. NXP Semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer's applications or products, or the application or use by customer's third party customer(s). Customer is responsible for doing all necessary testing for the customer's applications and products using NXP Semiconductors products in order to avoid a default of the applications and the products or of the application or use by customer's third party customer(s). NXP does not accept any liability in this respect. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the device. Limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the Recommended operating conditions section (if present) or the Characteristics sections of this document is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. Terms and conditions of commercial sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NXP Semiconductors hereby expressly objects to applying the customer's general terms and conditions with regard to the purchase of NXP Semiconductors products by customer. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 44 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply Export control -- This document as well as the item(s) described herein may be subject to export control regulations. Export might require a prior authorization from competent authorities. Non-automotive qualified products -- Unless this data sheet expressly states that this specific NXP Semiconductors product is automotive qualified, the product is not suitable for automotive use. It is neither qualified nor tested in accordance with automotive testing or application requirements. NXP Semiconductors accepts no liability for inclusion and/or use of non-automotive qualified products in automotive equipment or applications. In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without NXP Semiconductors' warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond NXP Semiconductors' specifications such use shall be solely at customer's own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors' standard warranty and NXP Semiconductors' product specifications. Translations -- A non-English (translated) version of a document is for reference only. The English version shall prevail in case of any discrepancy between the translated and English versions. 14.4 Trademarks Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners. GreenChip -- is a trademark of NXP B.V. 15. Contact information For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com TEA19161T Product data sheet All information provided in this document is subject to legal disclaimers. Rev. 1 -- 10 March 2016 (c) NXP Semiconductors N.V. 2016. All rights reserved. 45 of 46 TEA19161T NXP Semiconductors Digital controller for high-efficiency resonant power supply 16. Contents 1 2 2.1 2.2 2.3 3 4 5 6 6.1 6.2 7 7.1 7.1.1 7.1.2 7.1.3 7.2 7.3 7.3.1 7.3.2 7.4 7.4.1 7.4.2 7.4.3 7.5 7.6 7.6.1 7.6.2 7.6.3 7.6.4 7.6.5 7.6.6 7.6.7 7.6.8 7.7 7.7.1 7.7.2 7.7.3 7.8 7.9 7.9.1 7.9.2 7.9.3 7.9.4 8 9 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features and benefits . . . . . . . . . . . . . . . . . . . . 2 Distinctive features . . . . . . . . . . . . . . . . . . . . . . 2 Green features . . . . . . . . . . . . . . . . . . . . . . . . . 2 Protection features . . . . . . . . . . . . . . . . . . . . . . 2 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 3 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Pinning information . . . . . . . . . . . . . . . . . . . . . . 5 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . 6 Supply voltages . . . . . . . . . . . . . . . . . . . . . . . . 6 Start-up and supply voltage . . . . . . . . . . . . . . . 6 Regulated supply (SUPREG pin) . . . . . . . . . . . 8 High-side driver floating supply (SUPHS pin) . . 8 System start-up. . . . . . . . . . . . . . . . . . . . . . . . . 9 LLC system regulation . . . . . . . . . . . . . . . . . . 10 Output power regulation loop . . . . . . . . . . . . . 12 Output voltage start-up . . . . . . . . . . . . . . . . . . 13 Modes of operation . . . . . . . . . . . . . . . . . . . . . 14 High-power mode . . . . . . . . . . . . . . . . . . . . . . 16 Low-power mode . . . . . . . . . . . . . . . . . . . . . . 17 Burst mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Optobias regulation . . . . . . . . . . . . . . . . . . . . 21 Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Undervoltage protection SUPIC/SUPREG . . . 22 Undervoltage protection SUPHS . . . . . . . . . . 23 Undervoltage protection boost . . . . . . . . . . . . 23 Overvoltage protection . . . . . . . . . . . . . . . . . . 23 Capacitive Mode Regulation (CMR) . . . . . . . . 23 Overcurrent protection . . . . . . . . . . . . . . . . . . 24 Overtemperature protection . . . . . . . . . . . . . . 24 Overpower protection . . . . . . . . . . . . . . . . . . . 25 External settings . . . . . . . . . . . . . . . . . . . . . . . 26 Burst period . . . . . . . . . . . . . . . . . . . . . . . . . . 26 General settings . . . . . . . . . . . . . . . . . . . . . . . 26 Low-power mode/burst mode transition levels 27 Power good function . . . . . . . . . . . . . . . . . . . . 28 PFC/LLC communication protocol . . . . . . . . . 29 Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Fast latch reset . . . . . . . . . . . . . . . . . . . . . . . . 32 PFC burst mode . . . . . . . . . . . . . . . . . . . . . . . 33 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . 35 Thermal characteristics . . . . . . . . . . . . . . . . . 36 10 11 12 13 14 14.1 14.2 14.3 14.4 15 16 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . Application information . . . . . . . . . . . . . . . . . Package outline. . . . . . . . . . . . . . . . . . . . . . . . Revision history . . . . . . . . . . . . . . . . . . . . . . . Legal information . . . . . . . . . . . . . . . . . . . . . . Data sheet status . . . . . . . . . . . . . . . . . . . . . . Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . Contact information . . . . . . . . . . . . . . . . . . . . Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 41 42 43 44 44 44 44 45 45 46 Please be aware that important notices concerning this document and the product(s) described herein, have been included in section `Legal information'. (c) NXP Semiconductors N.V. 2016. All rights reserved. For more information, please visit: http://www.nxp.com For sales office addresses, please send an email to: salesaddresses@nxp.com Date of release: 10 March 2016 Document identifier: TEA19161T