GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Features RoHS Compliant Applications Compliant to RoHS II EU "Directive 2011/65/EU" Compatible in a Pb-free or SnPb reflow environment Compliant to IPC-9592 (September 2008), Category 2, Class II DOSA based Wide Input voltage range (3Vdc-14.4Vdc) Output voltage programmable from 0.6Vdc to 5.5Vdc via external resistor Tunable LoopTM to optimize dynamic output voltage response Power Good signal Distributed power architectures Fixed switching frequency Intermediate bus voltage applications Output overcurrent protection (non-latching) Telecommunications equipment Overtemperature protection Servers and storage applications Remote On/Off Networking equipment Ability to sink and source current Industrial equipment Cost efficient open frame design Small size: 12.2 mm x 12.2 mm x 8.5 mm (0.48 in x 0.48 in x 0.335 in) Wide operating temperature range [-40C to 105C(Ruggedized: -D), 85C(Regular)] UL* 60950-1Recognized, CSA C22.2 No. 60950-1-03 Certified, and VDE 0805:2001-12 (EN60950-1) Licensed ISO** 9001 and ISO 14001 certified manufacturing facilities Vin+ VIN PGOOD Vout+ VOUT SENSE MODULE Cin RTUNE CTUNE ON/OFF GND TRIM Co RTrim Description The 12A Analog PicoDLynxTM power modules are non-isolated dc-dc converters that can deliver up to 12A of output current. These modules operate over a wide range of input voltage (VIN = 3Vdc-14.4Vdc) and provide a precisely regulated output voltage from 0.6Vdc to 5.5Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage, over current and over temperature protection. The Tunable LoopTM feature allows the user to optimize the dynamic response of the converter to match the load with reduced amount of output capacitance leading to savings on cost and PWB area. November 14, 2018 (c)2014 General Electric Company. All rights reserved. GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Change History (excludes grammar & clarifications) V1.4, 4-23-2017 - changes over V1.3 p.20 - Updated figure to show height Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability. Parameter Device Symbol Min Max Unit All VIN -0.3 15 Vdc All TA -40 85 C -D version TA -40 105 C All Tstg -55 125 C Input Voltage Continuous Operating Ambient Temperature (see Thermal Considerations section) Storage Temperature Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Parameter Device Symbol Min Typ Max Unit Operating Input Voltage All VIN 3 14.4 Vdc Maximum Input Current All IIN,max 12 Adc VO,set = 0.6 Vdc IIN,No load 45 mA VO,set = 5Vdc IIN,No load 75 mA Input Stand-by Current (VIN = 12.0Vdc, module disabled) All IIN,stand-by 0.65 mA Inrush Transient All I2t Input Reflected Ripple Current, peak-to-peak (5Hz to 20MHz, 1H source impedance; VIN =0 to 14V, IO= IOmax ; See Test Configurations) All 40 mAp-p Input Ripple Rejection (120Hz) All -60 dB (VIN=3V to 14V, IO=IO, max ) Input No Load Current (VIN = 12.0Vdc, IO = 0, module enabled) November 14, 2018 (c)2014 General Electric Company. All rights reserved. 1 A2s Page 2 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Electrical Specifications (continued) Parameter Device Symbol Min Output Voltage Set-point (with 0.1% tolerance for external resistor used to set output voltage) All VO, set -1.0 Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life) All VO, set -3.0 Adjustment Range (selected by an external resistor) (Some output voltages may not be possible depending on the input voltage - see Feature Descriptions Section) All VO 0.6 Remote Sense Range All Typ Max Unit +1.0 % VO, set +3.0 % VO, set 5.5 Vdc 0.5 Vdc Output Regulation (for VO 2.5Vdc) Line (VIN=VIN, min to VIN, max) All +0.4 % VO, set Load (IO=IO, min to IO, max) All 10 mV Line (VIN=VIN, min to VIN, max) All 5 mV Load (IO=IO, min to IO, max) All 10 mV Temperature (Tref=TA, min to TA, max) All 0.4 % VO, set 50 100 mVpk-pk 20 38 mVrms Output Regulation (for VO < 2.5Vdc) Output Ripple and Noise on nominal output (VIN=VIN, nom and IO=IO, min to IO, max Co = 0.1F // 22 F ceramic capacitors) Peak-to-Peak (5Hz to 20MHz bandwidth) RMS (5Hz to 20MHz bandwidth) All All External Capacitance1 Without the Tunable LoopTM All CO, max 22 47 F ESR 0.15 m All CO, max 22 1000 F ESR 10 m All CO, max 22 5000 F Output Current (in either sink or source mode) All Io 0 12 Adc Output Current Limit Inception (Hiccup Mode) (current limit does not operate in sink mode) All IO, lim 200 % Io,max Output Short-Circuit Current All IO, s/c 1.5 Arms VO,set = 0.6Vdc 77.5 % VIN= 12Vdc, TA=25C VO, set = 1.2Vdc 85.9 % IO=IO, max , VO= VO,set VO,set = 1.8Vdc 89.6 % VO,set = 2.5Vdc 92.4 % VO,set = 3.3Vdc 93.4 % ESR 1 m With the Tunable LoopTM (VO250mV) ( Hiccup Mode ) Efficiency Switching Frequency VO,set = 5.0Vdc All fsw 95.0 600 % kHz External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient response. See the Tunable LoopTM section for details. 1 November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 3 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current General Specifications Parameter Device Calculated MTBF (IO=0.8IO, max, TA=40C) Telecordia Issue 2 Method 1 Case 3 Min All Typ Max 16,817,995 Weight 2.33(0.082) Unit Hours g (oz.) Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions for additional information. Parameter Device Symbol Input High Current All IIH Input High Voltage All VIH Min Typ Max Unit 1 mA 3.0 VIN,max Vdc On/Off Signal Interface (VIN=VIN, min to VIN, max ; open collector or equivalent, Signal referenced to GND) Device is with suffix "4" - Positive Logic (See Ordering Information) Logic High (Module ON) Logic Low (Module OFF) Input Low Current All IIL 10 A Input Low Voltage All VIL -0.2 0.3 Vdc Device Code with no suffix - Negative Logic (See Ordering Information) (On/OFF pin is open collector/drain logic input with external pull-up resistor; signal referenced to GND) Logic High (Module OFF) Input High Current All IIH 1 mA Input High Voltage All VIH 3.0 VIN, max Vdc Logic Low (Module ON) Input low Current All IIL 10 A Input Low Voltage All VIL -0.2 0.4 Vdc All Tdelay 5 msec All Tdelay 5 msec All Trise 2 Turn-On Delay and Rise Times (VIN=VIN, nom, IO=IO, max , VO to within 1% of steady state) Case 1: On/Off input is enabled and then input power is applied (delay from instant at which VIN = VIN, min until Vo = 10% of Vo, set) Case 2: Input power is applied for at least one second and then the On/Off input is enabled (delay from instant at which Von/Off is enabled until Vo = 10% of Vo, set) Output voltage Rise time (time for Vo to rise from 10% of Vo, set to 90% of Vo, set) Output voltage overshoot (TA = 25oC msec 3.0 % VO, set VIN= VIN, min to VIN, max,IO = IO, min to IO, max) With or without maximum external capacitance Over Temperature Protection All Tref 120/ 130 C (See Thermal Considerations section) November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 4 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Feature Specifications (cont.) Parameter Device Symbol Min Typ Max Units 2.9 Vdc Input Undervoltage Lockout Turn-on Threshold All Turn-off Threshold All Hysteresis All 2.6 Vdc 0.3 Vdc Overvoltage threshold for PGOOD 112.5 %VO, set Undervoltage threshold for PGOOD 87.5 %VO, set 30 PGOOD (Power Good) Signal Interface Open Drain, Vsupply 5VDC Pulldown resistance of PGOOD pin All Sink current capability into PGOOD pin All November 14, 2018 (c)2014 General Electric Company. All rights reserved. 5 mA Page 5 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 0.6Vo and 25oC. 90 12 85 10 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 80 Vin=3.3V 75 70 65 Vin=14.4 V Vin=12V 60 55 50 0 2 4 6 8 10 NC 8 Standard Part (85C) 6 4 2 0 85 95 105 OUTPUT VOLTAGE VO (V) (5mV/div) IO (A) (10Adiv) OUTPUT CURRENT, OUTPUT VOLTAGE VO (V) (20mV/div) TIME, t (20s /div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (200mV/div) Figure 4. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-3x47uF+6x330uF, CTune-47nF, RTune-180ohms OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (200mV/div) OUTPUT VOLTAGE ON/OFF VOLTAGE November 14, 2018 75 Figure 2. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (2ms/div) Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max). 65 AMBIENT TEMPERATURE, TA OC TIME, t (1s/div) Figure 3. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 2m/s (400LFM) 1m/s (200LFM) OUTPUT CURRENT, IO (A) Figure 1. Converter Efficiency versus Output Current. 1.5m/s (300LFM) Ruggedized (D) Part (105C) 55 12 0.5m/s (100LFM) TIME, t (2ms/div) Figure 6. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 6 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 1.2Vo and 25oC. 95 12 90 85 10 OUTPUT CURRENT, Io (A) Vin=3.3V EFFICIENCY, (%) 80 Vin=12V 75 Vin=14.4 V 70 65 60 55 50 NC 0.5m/s (100LFM) 8 6 Standard Part (85 C) 4 2m/s (400LFM) 2 Ruggedized (D) Part (105C) 2 4 6 8 10 12 55 65 OUTPUT CURRENT, IO (A) November 14, 2018 105 VO (V) (10mV/div) OUTPUT VOLTAGE INPUT VOLTAGE VIN (V) (5V/div) VO (V) (500mV/div) Figure 10. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-1x47uF+3x330uF, CTune-10nF & RTune-220ohms TIME, t (2ms/div) Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max). 95 TIME, t (20s /div) OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (5V/div) Figure 9. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 85 Figure 8. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, VO (V) (20mV/div) TIME, t (1s/div) 75 AMBIENT TEMPERATURE, TA OC IO (A) (10Adiv) Figure 7. Converter Efficiency versus Output Current. OUTPUT VOLTAGE 1.5m/s (300LFM) 0 0 OUTPUT VOLTAGE ON/OFF VOLTAGE 1m/s (200LFM) TIME, t (2ms/div) Figure 12. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 7 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 1.8Vo and 25oC. 100 12 95 10 Vin=3.3V OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 90 85 80 Vin=14.4 V Vin=12V 75 70 65 NC 0.5m/s (100LFM) 8 6 Standard Part (85C) 4 2 0 2 4 6 8 10 55 12 OUTPUT CURRENT, IO (A) 95 AO 105 C OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT CURRENT, TIME, t (20s /div) INPUT VOLTAGE VIN (V) (5V/div) OUTPUT VOLTAGE VO (V) (500mV/div) VON/OFF (V) (5V/div) VO (V) (500mV/div) November 14, 2018 85 Figure 16. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-1x47uF+2x330uF,CTune-5600pF & RTune-270ohms TIME, t (2ms/div) Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max). 75 AMBIENT TEMPERATURE, T TIME, t (1s/div) Figure 15. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 65 Figure 14. Derating Output Current versus Ambient Temperature and Airflow. IO (A) (10Adiv) VO (V) (20mV/div) Figure 13. Converter Efficiency versus Output Current. OUTPUT VOLTAGE 2m/s (400LFM) Ruggedized (D) Part (105C) 0 60 OUTPUT VOLTAGE ON/OFF VOLTAGE 1.5m/s (300LFM) 1m/s (200LFM) TIME, t (2ms/div) Figure 18. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 8 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 2.5Vo and 25oC. 100 12 95 10 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 90 85 80 Vin=14.4V Vin=12V Vin=4.5V 75 70 65 NC 0.5m/s (100LFM) 8 6 Standard Part (85C) 4 2 Ruggedized (D) Part (105C) 0 2 4 6 8 10 12 55 65 OUTPUT CURRENT, IO (A) 105 OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT CURRENT, INPUT VOLTAGE VIN (V) (5V/div) VO (V) (1V/div) Figure 22. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-1x47uF+1x330uF,CTune-3300pF & RTune-270ohms OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (1V/div) November 14, 2018 95 TIME, t (20s /div) TIME, t (2ms/div) Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max). 85 Figure 20. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (1s/div) Figure 21. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 75 AMBIENT TEMPERATURE, TA OC IO (A) (10Adiv) VO (V) (20mV/div) Figure 19. Converter Efficiency versus Output Current. OUTPUT VOLTAGE 1.5m/s (300LFM) 2m/s (400LFM) 0 60 OUTPUT VOLTAGE ON/OFF VOLTAGE 1m/s (200LFM) TIME, t (2ms/div) Figure 24. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 9 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 3.3Vo and 25oC. 100 12 95 OUTPUT CURRENT, Io (A) 10 EFFICIENCY, (%) 90 Vin=5V Vin=14.4 V 85 Vin=12V 80 75 NC 8 0.5m/s (100LFM) 6 4 1.5m/s (300LFM) 2 Ruggedized (D) Part (105C) 0 2 4 6 8 10 55 12 OUTPUT CURRENT, IO (A) 95 105 VO (V) (50mV/div) IO (A) (10Adiv) VO (V) (20mV/div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (1V/div) Figure 28. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-1x47uF+1x330uF,CTune-2700pF & RTune-330ohms OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (1V/div) November 14, 2018 85 TIME, t (20s /div) TIME, t (2ms/div) Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max). 75 Figure 26. Derating Output Current versus Ambient Temperature and Airflow. TIME, t (1s/div) Figure 27. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 65 AMBIENT TEMPERATURE, TA OC OUTPUT CURRENT OUTPUT VOLTAGE Figure 25. Converter Efficiency versus Output Current. OUTPUT VOLTAGE 2m/s (400LFM) 0 70 OUTPUT VOLTAGE ON/OFF VOLTAGE 1m/s (200LFM) Standard Part (85C) TIME, t (2ms/div) Figure 30. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 10 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Characteristic Curves The following figures provide typical characteristics for the 12A Analog PicoDLynxTM at 5Vo and 25oC. 100 12 95 OUTPUT CURRENT, Io (A) EFFICIENCY, (%) 10 90 Vin=7V Vin=14.4V 85 Vin=12V 80 75 NC 0.5m/s (100LFM) 8 6 Standard Part (85C) 4 1.5m/s (300LFM) 2 Ruggedized (D) Part (105C) 0 70 0 2 4 6 8 10 55 12 OUTPUT CURRENT, IO (A) 105 VO (V) (50mV/div) INPUT VOLTAGE VIN (V) (5V/div) VO (V) (2V/div) Figure 34. Transient Response to Dynamic Load Change from 50% to 100% at 12Vin, Cout-5x47uF, CTune-1500pF & RTune330ohms OUTPUT VOLTAGE VON/OFF (V) (5V/div) VO (V) (2V/div) OUTPUT VOLTAGE ON/OFF VOLTAGE November 14, 2018 75 85 95 AMBIENT TEMPERATURE, TA OC TIME, t (20s /div) TIME, t (2ms/div) Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max). 65 IO (A) (10Adiv) TIME, t (1s/div) Figure 33. Typical output ripple and noise (CO=22F ceramic, VIN = 12V, Io = Io,max, ). 2m/s (400LFM) Figure 32. Derating Output Current versus Ambient Temperature and Airflow. OUTPUT CURRENT, OUTPUT VOLTAGE VO (V) (20mV/div) OUTPUT VOLTAGE Figure 31. Converter Efficiency versus Output Current. 1m/s (200LFM) TIME, t (2ms/div) Figure 36. Typical Start-up Using Input Voltage (VIN = 12V, Io = Io,max). (c)2014 General Electric Company. All rights reserved. Page 11 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current 60 Input Filtering 50 Input Ripple Voltage (mVp-p) The 12A Analog PicoDLynxTM module should be connected to a low ac-impedance source. A highly inductive source can affect the stability of the module. An input capacitance must be placed directly adjacent to the input pin of the module, to minimize input ripple voltage and ensure module stability. To minimize input voltage ripple, ceramic capacitors are recommended at the input of the module. Figure 37 shows the input ripple voltage for various output voltages at 12A of load current with 2x22 F or 3x22 F ceramic capacitors and an input of 12V. 250 2x22uF 200 3x22uF Ripple (mVp-p) Design Considerations 1x22uF Ext 1x47uF Ext 2x47uF Ext 4x47uF Ext 40 Cap Cap Cap Cap 30 20 10 0 0.5 1.5 2.5 3.5 Output Voltage(Volts) 4.5 Figure 38. Output ripple voltage for various output voltages with external 1x22 F, 1x47 F, 2x47 F or 4x47 F ceramic capacitors at the output (12A load). Input voltage is 12V. Safety Considerations 150 100 50 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Output Voltage (Vdc) Figure 37. Input ripple voltage for various output voltages with 2x22 F or 3x22 F ceramic capacitors at the input (12A load). Input voltage is 12V. Output Filtering For safety agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards, i.e., UL 60950-1 2nd, CSA C22.2 No. 60950-1-07, DIN EN 609501:2006 + A11 (VDE0805 Teil 1 + A11):2009-11; EN 609501:2006 + A11:2009-03. For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a time delay fuse with a maximum rating of 15 A in the positive input lead. The 12A Analog PicoDLynxTM modules are designed for low output ripple voltage and will meet the maximum output ripple specification with 0.1 F ceramic and 22 F ceramic capacitors at the output of the module. However, additional output filtering may be required by the system designer for a number of reasons. First, there may be a need to further reduce the output ripple and noise of the module. Second, the dynamic response characteristics may need to be customized to a particular load step change. To reduce the output ripple and improve the dynamic response to a step load change, additional capacitance at the output can be used. Low ESR polymer and ceramic capacitors are recommended to improve the dynamic response of the module. Figure 38 provides output ripple information for different external capacitance values at various Vo and a full load current of 12A. For stable operation of the module, limit the capacitance to less than the maximum output capacitance as specified in the electrical specification table. Optimal performance of the module can be achieved by using the Tunable LoopTM feature described later in this data sheet November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 12 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Feature Descriptions VIN+ Remote On/Off MODULE Rpullup PicoDLynxTM The 12A Analog power modules feature an On/Off pin for remote On/Off operation. Two On/Off logic options are available. In the Positive Logic On/Off option, (device code suffix "4" - see Ordering Information), the module turns ON during a logic High on the On/Off pin and turns OFF during a logic Low. With the Negative Logic On/Off option, (no device code suffix, see Ordering Information), the module turns OFF during logic High and ON during logic Low. The On/Off signal should be always referenced to ground. For either On/Off logic option, leaving the On/Off pin disconnected will turn the module ON when input voltage is present. For positive logic modules, the circuit configuration for using the On/Off pin is shown in Figure 39. When the external transistor Q2 is in the OFF state, Q3 is ON, Q4 is OFF and the internal PWM Enable signal is pulled high and the module is ON. When transistor Q2 is turned ON, Q3 is OFF, Q4 turns ON pulling the ENABLE pin low and the module is OFF. A suggested value for Rpullup is 20k. VIN Rpullup 30K ON/OFF 22K ENABLE Q4 22K 0.047uF Q3 + 22K Q2 22K V ON/OFF _ ON/OFF Q4 + VON/OFF 22K Q1 CSS 22K GND _ PVX012 NEGATIVE LOGIC FIGURE Figure 40. Circuit configuration for using negative On/Off logic. Monotonic Start-up and Shutdown The module has monotonic start-up and shutdown behavior for any combination of rated input voltage, output current and operating temperature range. Startup into Pre-biased Output Output Voltage Programming 30K I ON/OFF The modules can start into a prebiased output as long as the prebias voltage is 0.5V less than the set output voltage. DLYNX MODULE +VIN PWM Enable I GND Figure 39. Circuit configuration for using positive On/Off logic. The output voltage of the module is programmable to any voltage from 0.6dc to 5.5Vdc by connecting a resistor between the Trim and GND pins of the module. Certain restrictions apply on the output voltage set point depending on the input voltage. These are shown in the Output Voltage vs. Input Voltage Set Point Area plot in Fig. 41. The Upper Limit curve shows that for output voltages lower than 1V, the input voltage must be lower than the maximum of 14.4V. The Lower Limit curve shows that for output voltages higher than 0.6V, the input voltage needs to be larger than the minimum of 3V. 16 14 Input Voltage (v) For negative logic On/Off modules, the circuit configuration is shown in Fig. 40. The On/Off pin should be pulled high with an external pull-up resistor (suggested value for the 3V to 14.4V input range is 20Kohms). When transistor Q1 is in the OFF state, the On/Off pin is pulled high, internal transistor Q4 is turned ON and the module is OFF. To turn the module ON, Q1 is turned ON pulling the On/Off pin low, turning transistor Q4 OFF resulting in the PWM Enable pin going high and the module turning ON. 12 Upper 10 8 6 4 Lower 2 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 Output Voltage (V) Figure 41. Output Voltage vs. Input Voltage Set Point Area plot showing limits where the output voltage can be set for different input voltages. November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 13 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Vo VIN(+) VO(+) Rmar gin-down MODULE VS+ ON/OFF Q2 LOAD TRIM Trim Rtrim Rmar gin-up Rtrim GND Figure 42. Circuit configuration for programming output voltage using an external resistor. Without an external resistor between Trim and GND pins, the output of the module will be 0.6Vdc. To calculate the value of the trim resistor, Rtrim for a desired output voltage, should be as per the following equation: Q1 G ND Figure 43. Circuit Configuration for margining Output voltage. 12 Rtrim k Vo 0.6 Overcurrent Protection Rtrim is the external resistor in k Vo is the desired output voltage. Table 1 provides Rtrim values required for some common output voltages. Table 1 VO, set (V) 0.6 0.9 1.0 1.2 1.5 1.8 2.5 3.3 5.0 Rtrim (K) Open 40 30 20 13.33 10 6.316 4.444 2.727 Remote Sense The power module has a Remote Sense feature to minimize the effects of distribution losses by regulating the voltage at the SENSE pin. The voltage between the SENSE pin and VOUT pin should not exceed 0.5V. Voltage Margining Output voltage margining can be implemented in the module by connecting a resistor, Rmargin-up, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, Rmargin-down, from the Trim pin to output pin for margining-down. Figure 43 shows the circuit configuration for output voltage margining. The POL Programming Tool, available at www.lineagepower.com under the Downloads section, also calculates the values of Rmargin-up and Rmargin-down for a specific output voltage and % margin. Please consult your local GE technical representative for additional details. November 14, 2018 To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting continuously. At the point of current-limit inception, the unit enters hiccup mode. The unit operates normally once the output current is brought back into its specified range. Overtemperature Protection To provide protection in a fault condition, the unit is equipped with a thermal shutdown circuit. The unit will shutdown if the overtemperature threshold of 120(Q1) / 130(L1)oC(typ) is exceeded at the thermal reference point Tref . Once the unit goes into thermal shutdown it will then wait to cool before attempting to restart. Input Undervoltage Lockout At input voltages below the input undervoltage lockout limit, the module operation is disabled. The module will begin to operate at an input voltage above the undervoltage lockout turn-on threshold. Power Good The module provides a Power Good (PGOOD) signal that is implemented with an open-drain output to indicate that the output voltage is within the regulation limits of the power module. The PGOOD signal will be de-asserted to a low state if any condition such as overtemperature, overcurrent or loss of regulation occurs that would result in the output voltage going 10% outside the setpoint value. The PGOOD terminal can be connected through a pullup resistor (suggested value 100K) to a source of 5VDC or lower. Dual Layout Identical dimensions and pin layout of Analog and Digital PicoDLynx modules permit migration from one to the other without needing to change the layout. To support this, 2 separate Trim Resistor locations have to be provided in the (c)2014 General Electric Company. All rights reserved. Page 14 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current layout. For the digital modules, the resistor is connected between the TRIM pad and SGND and in the case of the analog module it is connected between TRIM and GND MODULE TRIM (PVX012 / PDT012) Rtrim1 for Digital Rtrim2 for Analog SIG_GND GND (PIN 7) Caution - Do not connect SIG_GND to GND elsewhere in the layout Figure 44. Layout to support either Analog or Digital PicoDLynx on the same pad. Tunable LoopTM The 12A PicoDLynxTM modules have a feature that optimizes transient response of the module called Tunable LoopTM. External capacitors are usually added to the output of the module for two reasons: to reduce output ripple and noise (see Figure 38) and to reduce output voltage deviations from the steady-state value in the presence of dynamic load current changes. Adding external capacitance however affects the voltage control loop of the module, typically causing the loop to slow down with sluggish response. Larger values of external capacitance could also cause the module to become unstable. The Tunable LoopTM allows the user to externally adjust the voltage control loop to match the filter network connected to the output of the module. The Tunable LoopTM is implemented by connecting a series R-C between the SENSE and TRIM pins of the module, as shown in Fig. 45. This R-C allows the user to externally adjust the voltage loop feedback compensation of the module. VOUT SENSE RTUNE MODULE CO CTUNE TRIM GND RTrim Figure. 45. Circuit diagram showing connection of RTUNE and CTUNE to tune the control loop of the module. Recommended values of RTUNE and CTUNE for different output capacitor combinations are given in Tables 2 and 3. Table 2 shows the recommended values of RTUNE and CTUNE for different values of ceramic output capacitors up to 1000uF that might be needed for an application to meet output ripple and noise requirements. Selecting RTUNE and CTUNE according to Table 2 will ensure stable operation of the module. In applications with tight output voltage limits in the presence of dynamic current loading, additional output capacitance will be required. Table 3 lists recommended values of RTUNE and CTUNE in order to meet 2% output voltage deviation limits for some common output voltages in the presence of a 6A to 12A step change (50% of full load), with an input voltage of 12V. Please contact your GE technical representative to obtain more details of this feature as well as for guidelines on how to select the right value of external R-C to tune the module for best transient performance and stable operation for other output capacitance values or input voltages other than 12V. November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 15 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Table 2. General recommended values of of RTUNE and CTUNE for Vin=12V and various external ceramic capacitor combinations. Co 1x47F 2x47F 4x47F 6x47F 10x47F 20x47F RTUNE 330 330 330 330 270 180 CTUNE 100pF 560pF 1500pF 2200pF 3900pF 6800pF Table 3. Recommended values of RTUNE and CTUNE to obtain transient deviation of 2% of Vout for a 6A step load with Vin=12V. Vo 5V Co 5x47F 3.3V 2.5V 1.8V 99mV 0.6V 1x47F 3x47F 1x47F + 1x47F + 3x47F + + + 2x330F 3x330F 6x330F 330F 330F Polymer Polymer Polymer Polymer Polymer 330 270 270 220 180 RTUNE 330 CTUNE 1500pF 2700pF 3300pF 5600pF V 1.2V 58mV 47mV 34mV 10nF 47nF 24mV 12mV Note: The capacitors used in the Tunable Loop tables are 47 F/3 m ESR ceramic and 330 F/12 m ESR polymer capacitors. November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 16 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Thermal Considerations Power modules operate in a variety of thermal environments; however, sufficient cooling should always be provided to help ensure reliable operation. Considerations include ambient temperature, airflow, module power dissipation, and the need for increased reliability. A reduction in the operating temperature of the module will result in an increase in reliability. The thermal data presented here is based on physical measurements taken in a wind tunnel. The test set-up is shown in Figure 46. The preferred airflow direction for the module is in Figure 47. 25.4_ (1.0) Wind Tunnel Figure 47. Preferred airflow direction and location of hot-spot of the module (Tref). PWBs Power Module 76.2_ (3.0) x 12.7_ (0.50) Probe Location for measuring airflow and ambient temperature Air flow Figure 46. Thermal Test Setup. The thermal reference points, Tref used in the specifications are also shown in Figure 47. For reliable operation the temperature at Q1 should not exceed 120oC and the temperature at L1 should not exceed 130oC. The output power of the module should not exceed the rated power of the module (Vo,set x Io,max). Please refer to the Application Note "Thermal Characterization Process For Open-Frame Board-Mounted Power Modules" for a detailed discussion of thermal aspects including maximum device temperatures. November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 17 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Shock and Vibration The ruggedized (-D version) of the modules are designed to withstand elevated levels of shock and vibration to be able to operate in harsh environments. The ruggedized modules have been successfully tested to the following conditions: Non operating random vibration: Random vibration tests conducted at 25C, 10 to 2000Hz, for 30 minutes each level, starting from 30Grms (Z axis) and up to 50Grms (Z axis). The units were then subjected to two more tests of 50Grms at 30 minutes each for a total of 90 minutes. Operating shock to 40G per Mil Std. 810G, Method 516.4 Procedure I: The modules were tested in opposing directions along each of three orthogonal axes, with waveform and amplitude of the shock impulse characteristics as follows: All shocks were half sine pulses, 11 milliseconds (ms) in duration in all 3 axes. Units were tested to the Functional Shock Test of MIL-STD-810, Method 516.4, Procedure I - Figure 516.4-4. A shock magnitude of 40G was utilized. The operational units were subjected to three shocks in each direction along three axes for a total of eighteen shocks. Operating vibration per Mil Std 810G, Method 514.5 Procedure I: The ruggedized (-D version) modules are designed and tested to vibration levels as outlined in MIL-STD-810G, Method 514.5, and Procedure 1, using the Power Spectral Density (PSD) profiles as shown in Table 1 and Table 2 for all axes. Full compliance with performance specifications was required during the performance test. No damage was allowed to the module and full compliance to performance specifications was required when the endurance environment was removed. The module was tested per MIL-STD810, Method 514.5, Procedure I, for functional (performance) and endurance random vibration using the performance and endurance levels shown in Table 4 and Table 5 for all axes. The performance test has been split, with one half accomplished before the endurance test and one half after the endurance test (in each axis). The duration of the performance test was at least 16 minutes total per axis and at least 120 minutes total per axis for the endurance test. The endurance test period was 2 hours minimum per axis. Frequency (Hz) 10 30 40 50 90 110 130 140 Frequency (Hz) 10 30 40 50 90 110 130 140 November 14, 2018 Table 4: Performance Vibration Qualification - All Axes PSD Level PSD Level Frequency (Hz) Frequency (Hz) (G2/Hz) (G2/Hz) 1.14E-03 170 2.54E-03 690 5.96E-03 230 3.70E-03 800 9.53E-04 290 7.99E-04 890 2.08E-03 340 1.12E-02 1070 2.08E-03 370 1.12E-02 1240 7.05E-04 430 8.84E-04 1550 5.00E-03 490 1.54E-03 1780 8.20E-04 560 5.62E-04 2000 Table 5: Endurance Vibration Qualification - All Axes PSD Level PSD Level Frequency (Hz) Frequency (Hz) (G2/Hz) (G2/Hz) 0.00803 170 0.01795 690 0.04216 230 0.02616 800 0.00674 290 0.00565 890 0.01468 340 0.07901 1070 0.01468 370 0.07901 1240 0.00498 430 0.00625 1550 0.03536 490 0.01086 1780 0.0058 560 0.00398 2000 (c)2014 General Electric Company. All rights reserved. PSD Level (G2/Hz) 1.03E-03 7.29E-03 1.00E-03 2.67E-03 1.08E-03 2.54E-03 2.88E-03 5.62E-04 PSD Level (G2/Hz) 0.00727 0.05155 0.00709 0.01887 0.00764 0.01795 0.02035 0.00398 Page 18 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Example Application Circuit Requirements: Vin: 12V Vout: Iout: 1.8V 9A max., worst case load transient is from 6A to 9A Vout: Vin, ripple 1.5% of Vout (27mV) for worst case load transient 1.5% of Vin (180mV, p-p) Vin+ Vout+ VOUT VOUT VIN SENSE PGOOD + CI3 CI2 RTUNE MODULE CI1 + CTUNE ON/OFF CO1 CO3 TRIM GND RTrim CI1 Decoupling cap - 1x0.01F/16V ceramic capacitor (e.g. Murata LLL185R71E103MA01) CI2 2x22F/16V ceramic capacitor (e.g. Murata GRM32ER61C226KE20) CI3 470F/16V bulk electrolytic CO1 Decoupling cap - 1x0.01F/16V ceramic capacitor (e.g. Murata LLL185R71E103MA01) CO2 2 x 47F/6.3V ceramic capacitor (e.g. Murata GRM31CR60J476ME19) CO3 CTune RTune 1 x 330F/6.3V Polymer (e.g. Sanyo Poscap) 3300pF ceramic capacitor (can be 1206, 0805 or 0603 size) 270 ohms SMT resistor (can be 1206, 0805 or 0603 size) RTrim 10k SMT resistor (can be 1206, 0805 or 0603 size, recommended tolerance of 0.1%) November 14, 2018 CO2 (c)2014 General Electric Company. All rights reserved. Page 19 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Mechanical Outline Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) 17 16 13 14 12 15 November 14, 2018 11 7 8 9 PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 ON/OFF VIN GND VOUT VS+ (SENSE) TRIM GND NC NC 10 11 12 13 14 15 16 17 PGOOD NC NC NC NC NC NC NC (c)2014 General Electric Company. All rights reserved. Page 20 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Recommended Pad Layout Dimensions are in millimeters and (inches). Tolerances: x.x mm 0.5 mm (x.xx in. 0.02 in.) [unless otherwise indicated] x.xx mm 0.25 mm (x.xxx in 0.010 in.) 16 17 13 12 11 9 November 14, 2018 8 7 14 15 PIN FUNCTION PIN FUNCTION 1 2 3 4 5 6 7 8 9 ON/OFF VIN GND VOUT VS+ (SENSE) TRIM GND NC NC 10 11 12 13 14 15 16 17 PGOOD NC NC NC NC NC NC NC (c)2014 General Electric Company. All rights reserved. Page 21 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Packaging Details The 12V Analog PicoDLynxTM 12A modules are supplied in tape & reel as standard. Modules are shipped in quantities of 200 modules per reel. All Dimensions are in millimeters and (in inches). Reel Dimensions: Outside Dimensions: 330.2 mm (13.00) Inside Dimensions: Tape Width: 177.8 mm (7.00") 24.00 mm (0.945") November 14, 2018 (c)2014 General Electric Company. All rights reserved. Page 22 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current recommended profile requires testing to verify results and performance. Surface Mount Information Pick and Place The 12VAnalog PicoDLynxTM 12A modules use an open frame construction and are designed for a fully automated assembly process. The modules are fitted with a label designed to provide a large surface area for pick and place operations. The label meets all the requirements for surface mount processing, as well as safety standards, and is able to withstand reflow temperatures of up to 300oC. The label also carries product information such as product code, serial number and the location of manufacture. Nozzle Recommendations The module weight has been kept to a minimum by using open frame construction. Variables such as nozzle size, tip style, vacuum pressure and placement speed should be considered to optimize this process. The minimum recommended inside nozzle diameter for reliable operation is 3mm. The maximum nozzle outer diameter, which will safely fit within the allowable component spacing, is 7 mm. MSL Rating The 12VAnalog PicoDLynxTM 12A modules have a MSL rating of 2a. Storage and Handling The recommended storage environment and handling procedures for moisture-sensitive surface mount packages is detailed in J-STD-033 Rev. A (Handling, Packing, Shipping and Use of Moisture/Reflow Sensitive Surface Mount Devices). Moisture barrier bags (MBB) with desiccant are required for MSL ratings of 2 or greater. These sealed packages should not be broken until time of use. Once the original package is broken, the floor life of the product at conditions of 30C and 60% relative humidity varies according to the MSL rating (see J-STD-033A). The shelf life for dry packed SMT packages will be a minimum of 12 months from the bag seal date, when stored at the following conditions: < 40 C, < 90% relative humidity. Bottom Side / First Side Assembly 300 Per J-STD-020 Rev. D Lead Free Soldering The 12VAnalog PicoDLynxTM 12A modules are lead-free (Pbfree) and RoHS compliant and fully compatible in a Pb-free soldering process. Failure to observe the instructions below may result in the failure of or cause damage to the modules and can adversely affect long-term reliability. Pb-free Reflow Profile Power Systems will comply with J-STD-020 Rev. D (Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices) for both Pb-free solder profiles and MSL classification procedures. This standard provides a recommended forced-air-convection reflow profile based on the volume and thickness of the package (table 4-2). The suggested Pb-free solder paste is Sn/Ag/Cu (SAC). For questions regarding LGA, solder volume; please contact GE for special manufacturing process instructions. The recommended linear reflow profile using Sn/Ag/Cu solder is shown in Fig. 48. Soldering outside of the November 14, 2018 Peak Temp 260C 250 Reflow Temp (C) This module is not recommended for assembly on the bottom side of a customer board. If such an assembly is attempted, components may fall off the module during the second reflow process. 200 * Min. Time Above 235C 15 Seconds Cooling Zone 150 Heating Zone 1C/Second *Time Above 217C 60 Seconds 100 50 0 Reflow Time (Seconds) Figure 48. Recommended linear reflow profile using Sn/Ag/Cu solder. Post Solder Cleaning and Drying Considerations Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing. The result of inadequate cleaning and drying can affect both the reliability of a power module and the testability of the finished circuit-board assembly. For guidance on appropriate soldering, cleaning and drying procedures, refer to Board Mounted Power Modules: Soldering and Cleaning Application Note (AN04-001). (c)2014 General Electric Company. All rights reserved. Page 23 GE Data Sheet 12A Analog PicoDLynxTM: Non-Isolated DC-DC Power Modules 3Vdc -14.4Vdc input; 0.6Vdc to 5.5Vdc output; 12A Output Current Ordering Information Please contact your GE Sales Representative for pricing, availability and optional features. Table 6. Device Codes Device Code Input Voltage Range Output Voltage Output Current On/Off Logic Sequencing Comcodes PVX012A0X3-SRZ 3 - 14.4Vdc 0.6 - 5.5Vdc 12A Negative No CC109159686 PVX012A0X3-SRDZ 3 - 14.4Vdc 0.6 - 5.5Vdc 12A Negative No CC109168811 PVX012A0X43-SRDZ 3 - 14.4Vdc 0.6 - 5.5Vdc 12A Positive No CC109168828* PVX012A0X43-SRZ 3 - 14.4Vdc 0.6 - 5.5Vdc 12A Positive No CC109159694* -Z refers to RoHS compliant parts *Please contact GE for more information Table 7. Coding Scheme Package Identifier Family P P=Pico U=Micro M=Mega G=Giga Sequencing Option Output current Output voltage V X 012A0 X D=Dlynx Digital T=with EZ Sequence 12A V= DLynx Analog. X=without sequencing On/Off logic X= 4= programm positive able output No entry = negative Remote Sense ROHS Compliance Options 3 -SR -D Z 3= Remote Sense S= Surface Mount D = 105C operating ambient, 40G operating shock as per MIL Std 810G Z = ROHS6 R= Tape & Reel Contact Us For more information, call us at USA/Canada: +1 888 546 3243, or +1 972 244 9288 Asia-Pacific: +86.021.54279977*808 Europe, Middle-East and Africa: +49.89.878067-280 www.gecriticalpower.com GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. November 14, 2018 (c)2016 General Electric Company. All International rights reserved. Version 1.5