10.7 Gbps Active Back-Termination, Differential Laser Diode Driver ADN2525 FEATURES GENERAL DESCRIPTION Up to 10.7 Gbps operation Very low power: 670 mW (IBIAS = 40 mA, IMOD = 40 mA) Typical 24 ps rise/fall times Full back-termination of output transmission lines Compatible with XMD-MSA TOSA Drives TOSAs with resistances ranging from 5 to 50 PECL-/CML-compatible data inputs Bias current range: 10 mA to 100 mA Differential modulation current range: 10 mA to 80 mA Automatic laser shutdown (ALS) 3.3 V operation Compact 3 mm x 3 mm LFCSP Voltage input control for bias and modulation currents XFP-compliant bias current monitor Optical evaluation board available The ADN2525 laser diode driver is designed for direct modulation of packaged laser diodes having a differential resistance ranging from 5 to 50 . The active back-termination technique provides excellent matching with the output transmission lines while reducing the power dissipation in the output stage. The back-termination in the ADN2525 absorbs signal reflections from the TOSA end of the output transmission lines, enabling excellent optical eye quality to be achieved even when the TOSA end of the output transmission lines is significantly misterminated. The small package provides the optimum solution for compact modules where laser diodes are packaged in low pin-count optical subassemblies. The modulation and bias currents are programmable via the MSET and BSET control pins. By driving these pins with control voltages, the user has the flexibility to implement various average power and extinction ratio control schemes, including closed-loop control and look-up tables. The automatic laser shutdown (ALS) feature allows the user to turn on/off the bias and modulation currents by driving the ALS pin with the proper logic levels. APPLICATIONS SONET OC-192 optical transceivers SDH STM-64 optical transceivers 10 Gb Ethernet optical transceivers XFP/X2/XENPAK/XPAK/MSA 300 optical modules SR and VSR optical links The product is available in a space-saving 3 mm x 3 mm LFCSP specified from -40C to +85C. FUNCTIONAL BLOCK DIAGRAM VCC ALS VCC ADN2525 VCC 50 IMODP 50 50 GND IMOD IMODN VCC DATAP DATAN IBMON IBIAS 800 800 MSET GND BSET 200 2 05077-001 200 200 Figure 1. Rev. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved. ADN2525 TABLE OF CONTENTS Features .............................................................................................. 1 Bias Current ...................................................................................9 Applications....................................................................................... 1 Automatic Laser Shutdown (ALS) ........................................... 10 General Description ......................................................................... 1 Modulation Current................................................................... 10 Functional Block Diagram .............................................................. 1 Load Mistermination ................................................................. 12 Revision History ............................................................................... 2 Power Consumption .................................................................. 12 Specifications..................................................................................... 3 Applications Information .............................................................. 13 Thermal Specifications ................................................................ 4 Typical Application Circuit....................................................... 13 Absolute Maximum Ratings............................................................ 5 Layout Guidelines....................................................................... 13 ESD Caution.................................................................................. 5 Design Example.......................................................................... 14 Pin Configuration and Function Descriptions............................. 6 Outline Dimensions ....................................................................... 15 Typical Performance Characteristics ............................................. 7 Ordering Guide .......................................................................... 15 Theory of Operation ........................................................................ 9 Input Stage..................................................................................... 9 REVISION HISTORY 8/06--Rev. 0 to Rev. A Changes to Format .............................................................Universal Changes to Features and Figure 1................................................... 1 Changes to Table 1............................................................................ 3 Changes to Table 3............................................................................ 5 Changes to Figure 19........................................................................ 9 Changes to Figure 25...................................................................... 10 Changes to Modulation Current Section and Figure 29 ........... 11 Changes to Typical Application Circuit Section......................... 13 Changes to Ordering Guide .......................................................... 15 3/05--Revision 0: Initial Version Rev. A | Page 2 of 16 ADN2525 SPECIFICATIONS VCC = VCCMIN to VCCMAX, TA = -40C to +85C, 50 differential load resistance, unless otherwise noted. Typical values are specified at 25C, IMOD = 40 mA. Table 1. Parameter BIAS CURRENT (IBIAS) Bias Current Range Bias Current while ALS Asserted Compliance Voltage 1 MODULATION CURRENT (IMODP, IMODN) Modulation Current Range Modulation Current While ALS Asserted Rise Time (20% to 80%) 2, 3 Fall Time (20% to 80%)2, 3 Random Jitter2, 3 Deterministic Jitter3, 4 Pulse-Width Distortion2, 3 Differential |S22| Compliance Voltage1 DATA INPUTS (DATAP, DATAN) Input Data Rate Differential Input Swing Differential |S11| Input Termination Resistance BIAS CONTROL INPUT (BSET) BSET Voltage to IBIAS Gain BSET Input Resistance MODULATION CONTROL INPUT (MSET) MSET Voltage to IMOD Gain MSET Input Resistance BIAS MONITOR (IBMON) IBMON to IBIAS Ratio Accuracy of IBIAS to IBMON Ratio AUTOMATIC LASER SHUTDOWN (ALS) VIH VIL IIL IIH ALS Assert Time Min Typ 10 0.6 0.6 10 24 24 0.4 7.2 2 -10 -14 Unit Test Conditions/Comments 100 100 VCC - 1.2 VCC - 0.8 mA A V V ALS = high IBIAS = 100 mA IBIAS = 10 mA 80 0.5 32.5 32.5 0.9 12 5 mA diff mA diff ps ps ps rms ps p-p ps dB dB V VCC - 1.1 VCC + 1.1 0.4 10.7 1.6 85 -16.8 100 115 Gbps V p-p diff dB 75 800 100 1000 120 1200 mA/V 70 800 88 1000 110 1200 mA/V +5.0 +4.0 +2.5 +2 A/mA % % % % 0.8 +20 200 2 V V A A s 10 s 3.53 45 176 V mA mA 10 -5.0 -4.0 -2.5 -2 2.4 -20 0 ALS Negate Time POWER SUPPLY VCC ICC 5 ISUPPLY 6 Max 3.07 3.3 39 157 See notes on next page. Rev. A | Page 3 of 16 RLOAD = 5 to 50 differential ALS = high Includes pulse-width distortion PWD = ABS(THIGH - TLOW)/2 5 GHz < f < 10 GHz, Z0 = 50 differential f < 5 GHz, Z0 = 50 differential NRZ Differential ac-coupled f < 10 GHz, Z0 = 100 differential Differential See Figure 29 10 mA IBIAS < 20 mA, RIBMON = 1 k 20 mA IBIAS < 40 mA, RIBMON = 1 k 40 mA IBIAS < 70 mA, RIBMON = 1 k 70 mA IBIAS < 100 mA, RIBMON = 1 k Rising edge of ALS to fall of IBIAS and IMOD below 10% of nominal; see Figure 2 Falling edge of ALS to rise of IBIAS and IMOD above 90% of nominal; see Figure 2 VBSET = VMSET = 0 V VBSET = VMSET = 0 V; ISUPPLY = ICC + IMODP + IMODN ADN2525 1 Refers to the voltage between the pin for which the compliance voltage is specified and GND. The pattern used is composed by a repetitive sequence of eight 1s followed by eight 0s at 10.7 Gbps. 3 Measured using the high speed characterization circuit shown in Figure 3. 4 The pattern used is K28.5 (00111110101100000101) at a 10.7 Gbps rate. 5 Only includes current in the ADN2525 VCC pins. 6 Includes current in ADN2525 VCC pins and dc current in IMODP and IMODN pull-up inductors. See the Power Consumption section for total supply current calculation. 2 THERMAL SPECIFICATIONS Table 2. Parameter J-PAD J-TOP IC Junction Temperature Min 2.6 65 Typ 5.8 72.2 Max 10.7 79.4 125 Unit C/W C/W C Conditions/Comments Thermal resistance from junction to bottom of exposed pad Thermal resistance from junction to top of package ALS NEGATE TIME ALS t IBIAS AND IMOD 90% 10% 05077-002 t ALS ASSERT TIME Figure 2. ALS Timing Diagram VEE VEE VEE GND 10 1k VBSET TP1 10nF TP2 GND VCC VCC GND GND ADN2525 Z0 = 50 10nF Z0 = 50 J2 DATAP GND Z0 = 25 J3 DATAN GND GND Z0 = 25 IMODP GND GND GND Z0 = 50 10nF Z0 = 50 GND GND IMODN 35 GND VCC MSET VCC NC1 ALS VMSET GND 10nF VEE VEE J8 GND J5 GND GND GND GND VEE GND 50 ADAPTER ATTENUATOR ADAPTER ATTENUATOR GND OSCILLOSCOPE 70 Z = 50 35 0 GND GND Z0 = 50 BIAS TEE BIAS TEE 50 GND GND BIAS TEE: PICOSECOND PULSE LABS MODEL 5542-219 ADAPTER: PASTERNACK PE-9436 2.92mm FEMALE-TO-FEMALE ADAPTER ATTENUATOR: PASTERNACK PE-7046 2.92mm 20dB ATTENUATOR 22F GND Figure 3. High Speed Characterization Circuit Rev. A | Page 4 of 16 05077-003 BSET IBMON IBIAS ADN2525 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Supply Voltage, VCC to GND IMODP, IMODN to GND DATAP, DATAN to GND All Other Pins Junction Temperature Storage Temperature Range Soldering Temperature (Less than 10 sec) Min -0.3 VCC - 1 .5 VCC - 1.8 -0.3 -65 Max +4.2 4.75 VCC - 0.4 VCC + 0.3 150 +150 300 Unit V V V V C C C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. A | Page 5 of 16 ADN2525 13 VCC 14 DATAP TOP VIEW (Not to Scale VCC 5 GND 4 ADN2525 12 BSET 11 IBMON 10 IBIAS 9 GND VCC 8 ALS 3 PIN 1 INDICATOR IMODN 6 IMODP 7 NC 2 NC = NO CONNECT 05077-016 MSET 1 15 DATAN 16 VCC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 4. Pin Configuration Note that the exposed pad on the bottom of the package must be connected to the VCC or GND plane. Table 4. Pin Function Description Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Exposed Pad Mnemonic MSET NC ALS GND VCC IMODN IMODP VCC GND IBIAS IBMON BSET VCC DATAP DATAN VCC Pad I/O Input N/A Input Power Power Output Output Power Power Output Output Input Power Input Input Power Power Description Modulation Current Control Input No Connect--Leave Floating Automatic Laser Shutdown Negative Power Supply Positive Power Supply Modulation Current Negative Output Modulation Current Positive Output Positive Power Supply Negative Power Supply Bias Current Output Bias Current Monitoring Output Bias Current Control Input Positive Power Supply Data Signal Positive Input Data Signal Negative Input Positive Power Supply Connect to GND or VCC Rev. A | Page 6 of 16 ADN2525 TYPICAL PERFORMANCE CHARACTERISTICS TA = 25C, VCC = 3.3 V, unless otherwise noted. 28.0 9 27.5 8 DETERMINISTIC JITTER (ps p-p) 27.0 26.0 25.5 25.0 24.5 24.0 6 5 4 3 2 20 40 60 80 DIFFERENTIAL MODULATION CURRENT (mA) 100 0 05077-004 0 0 20 40 60 80 DIFFERENTIAL MODULATION CURRENT (mA) Figure 5. Rise Time vs. IMOD Figure 8. Deterministic Jitter vs. IMOD 27.5 350 TOTAL SUPPLY CURRENT (mA) 26.0 FALL TIME (ps) IBIAS = 100mA 300 26.5 25.5 25.0 24.5 24.0 23.5 20 40 60 80 DIFFERENTIAL MODULATION CURRENT (mA) 100 IBIAS = 10mA 200 150 100 50 0 05077-005 0 IBIAS = 50mA 250 0 20 40 60 80 DIFFERENTIAL MODULATION CURRENT (mA) Figure 9. Total Supply Current vs. IMOD 0.7 0 0.6 -5 -10 DIFFERENTIAL |S11| (dB) 0.5 0.4 0.3 0.2 0.1 0 -15 -20 -25 -30 -35 0 20 40 60 80 DIFFERENTIAL MODULATION CURRENT (mA) 100 -40 05077-006 RANDOM JITTER (ps rms) Figure 6. Fall Time vs. IMOD 100 05077-008 27.0 23.0 100 05077-007 1 23.5 23.0 7 0 Figure 7. Random Jitter vs. IMOD 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) Figure 10. Differential |S11| Rev. A | Page 7 of 16 05077-009 RISE TIME (ps) 26.5 ADN2525 (ACQ LIMIT TEST) WAVEFORMS: 1000 0 DIFFERENTIAL |S22| (dB) -5 -10 -15 -20 -25 -30 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 FREQUENCY (GHz) 05077-010 -40 05077-013 -35 Figure 11. Differential |S22| Figure 14. Electrical Eye Diagram (10.7 Gbps, PRBS31, IMOD = 80 mA) 16 14 % OCCURRENCE 12 10 8 6 4 23 24 25 26 27 RISE TIME (ps) 28 29 30 05077-014 0 05077-011 2 Figure 15. Filtered SONET OC192 Optical Eye Diagram (for Reference) (PRBS31 Pattern, PAV = -2 dBm, ER = 7 dB, 17% Mask Margin, NEC NX8341UJ TOSA) Figure 12. Worst-Case Rise Time Distribution (VCC = 3.07 V, IBIAS = 100 mA, IMOD = 80 mA, TA = 85C) 16 14 10 8 6 4 2 23 24 25 26 27 FALL TIME (ps) 28 29 30 05077-015 0 05077-012 % OCCURRENCE 12 Figure 13. Worst-Case Fall Time Distribution (VCC = 3.07 V, IBIAS = 100 mA, IMOD = 80 mA, TA = 85C) Figure 16. Filtered 10G Ethernet Optical Eye (PRBS31 Pattern, PAV = -2 dBm, ER = 5 dB, 41% Mask Margin, NEC NX8341UJ TOSA) Rev. A | Page 8 of 16 ADN2525 THEORY OF OPERATION The ADN2525 input stage must be ac-coupled to the signal source to eliminate the need for matching between the commonmode voltages of the data signal source and the input stage of the driver (see Figure 18). The ac-coupling capacitors should have an impedance less than 50 over the required frequency range. Generally, this is achieved using 10 nF to 100 nF capacitors. 50 50 ADN2525 C DATAP DATAN C 05077-018 As shown in Figure 1, the ADN2525 consists of an input stage and two voltage-controlled current sources for bias and modulation. The bias current is available at the IBIAS pin. It is controlled by the voltage at the BSET pin and can be monitored at the IBMON pin. The differential modulation current is available at the IMODP and IMODN pins. It is controlled by the voltage at the MSET pin. The output stage implements the active back-match circuitry for proper transmission line matching and power consumption reduction. The ADN2525 can drive a load having differential resistance ranging from 5 to 50 . The excellent back-termination in the ADN2525 absorbs signal reflections from the TOSA end of the output transmission lines, enabling excellent optical eye quality to be achieved even when the TOSA end of the output transmission lines is significantly misterminated. DATA SIGNAL SOURCE Figure 18. AC-Coupling the Data Source to the ADN2525 Data Inputs INPUT STAGE The input stage of the ADN2525 converts the data signal applied to the DATAP and DATAN pins to a level that ensures proper operation of the high speed switch. The equivalent circuit of the input stage is shown in Figure 17. BIAS CURRENT The bias current is generated internally using a voltage-to-current converter consisting of an internal operational amplifier and a transistor, as shown in Figure 19. VCC VCC ADN2525 R R DATAP 50 IBMON VCC BSET IBMON 800 IBIAS IBIAS VCC 200 200 05077-017 DATAN GND 2 05077-019 50 Figure 17. Equivalent Circuit of the Input Stage Figure 19. Voltage-to-Current Converter Used to Generate IBIAS The DATAP and DATAN pins are terminated internally with a 100 differential termination resistor. This minimizes signal reflections at the input, which could otherwise lead to degradation in the output eye diagram. It is not recommended to drive the ADN2525 with single-ended data signal sources. The voltage-to-current conversion factor is set at 100 mA/V by the internal resistors, and the bias current is monitored using a current mirror with a gain equal to 1/100. By connecting a 1 k resistor between IBMON and GND, the bias current can be monitored as a voltage across the resistor. A low temperature coefficient precision resistor must be used for the IBMON resistor (RIBMON). Any error in the value of RIBMON due to tolerances, or drift in its value over temperature, contributes to the overall error budget for the IBIAS monitor voltage. If the IBMON voltage is being connected to an ADC for A/D conversion, RIBMON should be placed close to the ADC to minimize errors due to voltage drops on the ground plane. Rev. A | Page 9 of 16 ADN2525 The equivalent circuits of the BSET, IBIAS, and IBMON pins are shown in Figure 20, Figure 21, and Figure 22. VCC VCC AUTOMATIC LASER SHUTDOWN (ALS) BSET The ALS pin is a digital input that enables/disables both the bias and modulation currents, depending on the logic state applied, as shown in Table 5. 800 05077-020 200 Table 5. Figure 20. Equivalent Circuit of the BSET Pin IBIAS ALS Logic State High Low Floating VCC VCC The function of the inductor L is to isolate the capacitance of the IBIAS output from the high frequency signal path. For recommended components, see Table 6. 2k IBIAS and IMOD Disabled Enabled Enabled 100 The ALS pin is compatible with 3.3 V CMOS and TTL logic levels. Its equivalent circuit is shown in Figure 24. 05077-021 VCC Figure 21. Equivalent Circuit of the IBIAS Pin VCC VCC VCC 100 ALS 50k 500 05077-024 2 2k Figure 24. Equivalent Circuit of the ALS Pin MODULATION CURRENT 100 IBMON 05077-022 VCC Figure 22. Equivalent Circuit of the IBMON Pin The recommended configuration for BSET, IBIAS, and IBMON is shown in Figure 23. The modulation current can be controlled by applying a dc voltage to the MSET pin. This voltage is converted into a dc current by using a voltage-to-current converter using an operational amplifier and a bipolar transistor, as shown in Figure 25. VCC TO LASER CATHODE L IMODP IBIAS 50 IBIAS IMOD IMODN ADN2525 BSET GND MSET RIBMON 1k 800 05077-023 VBSET FROM INPUT STAGE IBMON The circuit used to drive the BSET voltage must be able to drive the 1 k input resistance of the BSET pin. For proper operation of the bias current source, the voltage at the IBIAS pin must be between the compliance voltage specifications for this pin over supply, temperature, and bias current range (see Table 1). The maximum compliance voltage is specified for only two bias current levels (10 mA and 100 mA), but it can be calculated for any bias current by VCOMPLIANCE_MAX (V) = VCC (V) - 0.75 - 4.4 x IBIAS (A) See the Applications Information section for examples of headroom calculations. 200 ADN2525 GND Figure 25. Generation of Modulation Current on the ADN2525 This dc current is switched by the data signal applied to the input stage (DATAP and DATAN pins) and gained up by the output stage to generate the differential modulation current at the IMODP and IMODN pins. The output stage also generates the active back-termination, which provides proper transmission line termination. Active back-termination uses feedback around an active circuit to synthesize a broadband termination resistance. This provides Rev. A | Page 10 of 16 05077-025 Figure 23. Recommended Configuration for the BSET, IBIAS, and IBMON Pins ADN2525 210 200 190 180 170 VCC MSET 05077-026 800 200 160 140 120 100 80 70 VCC IMODP Figure 27. Equivalent Circuit of the IMODP and IMODN Pins VCC ADN2525 L Z0 = 25 L Z0 = 25 C IMODP TOSA Z0 = 25 VMSET Z0 = 25 C IMODN GND L L VCC VCC 05077-028 MSET 10 15 20 25 30 35 40 45 DIFFERENTIAL LOAD RESISTANCE 50 55 The circuit used to drive the MSET voltage must be able to drive the 1 k resistance of the MSET pin. To be able to drive 80 mA modulation currents through the differential load, the output stage of the ADN2525 (the IMODP and IMODN pins) must be ac-coupled to the load. The voltages at these pins have a dc component equal to VCC and an ac component with single-ended, peak-to-peak amplitude of IMOD x 25 . This is the case even if the load impedance is less than 50 differential, because the transmission line characteristic impedance sets the peak-to-peak amplitude. For proper operation of the output stage, the voltages at the IMODP and IMODN pins must be between the compliance voltage specifications for this pin over supply, temperature, and modulation current range, as shown in Figure 30. See the Applications Information section for examples of headroom calculations. The recommended configuration of the MSET, IMODP, and IMODN pins is shown in Figure 28. See Table 6 for recommended components. IBIAS 5 Using the resistance of the TOSA, the user can calculate the voltage range that should be applied to the MSET pin to generate the required modulation current range (see the example in the Applications Information section). 3.3 05077-027 3.3 0 Figure 29. MSET Voltage-to-Modulation Current Ratio vs. Differential Load Resistance 25 25 MINIMUM 110 60 IMODN TYPICAL 130 90 Figure 26. Equivalent Circuit of the MSET Pin VCC MAXIMUM 150 05077-029 VCC The ratio between the voltage applied to the MSET pin and the differential modulation current available at the IMODP and IMODN pins is a function of the load resistance value, as shown in Figure 29. IMOD/VMSET (mA/V) excellent transmission line termination, while dissipating less power than a traditional resistor passive back-termination. No portion of the modulation current flows in the active backtermination resistance. All of the preset modulation current IMOD, the range specified in Table 1, flows in the external load. The equivalent circuits for MSET, IMODP, and IMODN are shown in Figure 26 and Figure 27. The two 25 resistors in Figure 27 are not real resistors; they represent the active backtermination resistance. Figure 28. Recommended Configuration for the MSET, IMODP, and IMODN Pins Rev. A | Page 11 of 16 ADN2525 IMODP, IMODN Table 2. For improved heat dissipation, the module's case can be used as heat sink, as shown in Figure 31. A compact optical module is a complex thermal environment, and calculations of device junction temperature using the package JA (junction-toambient thermal resistance) do not yield accurate results. VCC + 1.1V THERMAL COMPOUND NORMAL OPERATION REGION MODULE CASE VCC TTOP VCC - 1.1V DIE TJ THERMOCOUPLE PACKAGE 05077-030 T PAD PCB 05077-031 Figure 30. Allowable Range for the Voltage at IMODP and IMODN COPPER PLANE VIAS LOAD MISTERMINATION Figure 31. Typical Optical Module Structure Due to its excellent S22 performance, the ADN2525 can drive differential loads that range from 5 to 50 . In practice, many TOSAs have differential resistance less than 50 . In this case, with 50 differential transmission lines connecting the ADN2525 to the load, the load end of the transmission lines are misterminated. This mistermination leads to signal reflections back to the driver. The excellent back-termination in the ADN2525 absorbs these reflections, preventing their reflection back to the load. This enables excellent optical eye quality to be achieved, even when the load end of the transmission lines is significantly misterminated. The connection between the load and the ADN2525 must be made with 50 differential (25 single-ended) transmission lines so that the driver end of the transmission lines is properly terminated. The following procedure can be used to estimate the IC junction temperature: * TTOP is the temperature at top of package in C. * TPAD is the temperature at package exposed paddle in C. * TJ is the IC junction temperature in C. * P is the power dissipation in W. * J-TOP is the thermal resistance from IC junction to package top. * J-PAD is the thermal resistance from IC junction to package exposed pad. TTOP J-TOP POWER CONSUMPTION The power dissipated by the ADN2525 is given by J-PAD P V P = VCC x MSET + I SUPPLY + VIBIAS x IBIAS 13.5 TTOP TPAD where: 05077-032 TPAD Figure 32. Electrical Model for Thermal Calculations VCC is the power supply voltage. TTOP and TPAD can be determined by measuring the temperature at points inside the module, as shown in Figure 31. The thermocouples should be positioned to obtain an accurate measurement of the package top and paddle temperatures. Using the model shown in Figure 32, the junction temperature can be calculated by IBIAS is the bias current generated by the ADN2525. VMSET is the voltage applied to the MSET pin. ISUPPLY is the sum of the current that flows into the VCC, IMODP, and IMODN pins of the ADN2525 when IBIAS = IMOD = 0 expressed in amps (see Table 1). TJ = VIBIAS is the average voltage on the IBIAS pin. Considering VBSET/IBIAS = 10 as the conversion factor from VBSET to IBIAS, the dissipated power becomes ( ) P x J -PAD x J -TOP + TTOP x J -PAD + TPAD x J -TOP J -PAD + J -TOP where: J-TOP and J-PAD are given in Table 2. V V P = VCC x MSET + I SUPPLY + BSET x VIBIAS 10 13.5 P is the power dissipated by the ADN2525. To ensure long-term reliable operation, the junction temperature of the ADN2525 must not exceed 125C, as specified in Rev. A | Page 12 of 16 ADN2525 APPLICATIONS INFORMATION TYPICAL APPLICATION CIRCUIT LAYOUT GUIDELINES Figure 33 shows the typical application circuit for the ADN2525. The dc voltages applied to the BSET and MSET pins control the bias and modulation currents. The bias current can be monitored as a voltage drop across the 1 k resistor connected between the IBMON pin and GND. The ALS pin allows the user to turn on/off the bias and modulation currents, depending on the logic level applied to the pin. The data signal source must be connected to the DATAP and DATAN pins of the ADN2525 using 50 transmission lines. The modulation current outputs, IMODP and IMODN, must be connected to the load (TOSA) using 50 differential (25 single-ended) transmission lines. Table 6 shows recommended components for the ac-coupling interface between the ADN2525 and TOSA. For up-to-date component recommendations, contact sales. Due to the high frequencies at which the ADN2525 operates, care should be taken when designing the PCB layout to obtain optimum performance. Controlled impedance transmission lines must be used for the high speed signal paths. The length of the transmission lines must be kept to a minimum to reduce losses and pattern-dependent jitter. The PCB layout must be symmetrical, both on the DATAP and DATAN inputs and on the IMODP and IMODN outputs, to ensure a balance between the differential signals. All VCC and GND pins must be connected to solid copper planes by using low inductance connections. When the connections are made through vias, multiple vias can be connected in parallel to reduce the parasitic inductance. Each GND pin must be locally decoupled with high quality capacitors. If proper decoupling cannot be achieved using a single capacitor, the user can use multiple capacitors in parallel for each GND pin. A 20 F tantalum capacitor must be used as a general decoupling capacitor for the entire module. For guidelines on the surface-mount assembly of the ADN2525, see Amkor Technology(R) Application Notes for Surface Mount Assembly of Amkor's MicroLeadFrame(R) (MLF) Packages. Working with a TOSA laser sample, the circuit in Figure 33 delivers the optical performance shown in Figure 15 and Figure 16. For additional applications information and optical eye performance of other laser samples, contact ADI sales or see the ADN2525 application notes at www.analog.com. Table 6. Value 36 200 100 nF L2, L3, L6, L7 82 nH L1, L4, L5, L8 10 H Description 0603 size resistor 0603 size resistor 0603 size capacitor, Phycomp 223878615649 0402 size inductor, Murata LQW15AN82NJ0 0603 size inductor, Murata LQM21FN100M70L VCC GND BSET R5 1k GND C5 10nF TP1 L1 R1 L8 R4 VCC VCC BSET IBMON IBIAS GND VCC VCC Z0 = 50 VCC L2 L7 Z0 = 25 DATAP DATAP C1 DATAN DATAN Z0 = 25 VCC MSET NC1 Z0 = 25 TOSA IMODN C2 VCC C4 GND ADN2525 Z0 = 50 Z0 = 25 IMODP ALS VCC GND GND L3 VCC C3 L6 VCC C6 10nF MSET 3.3V VCC C7 200F GND ALS L4 R2 L5 R3 GND VCC Figure 33. Typical ADN2525 Application Circuit Rev. A | Page 13 of 16 VCC 05077-033 Component R1, R2 R3, R4 C3, C4 ADN2525 DESIGN EXAMPLE This design example covers: * Headroom calculations for IBIAS, IMODP, and IMODN pins. Assuming VLB = 0 V and IMOD = 60 mA, the minimum voltage at the modulation output pins is equal to VCC - (IMOD x 25)/2 = VCC - 0.75 * Calculation of the typical voltage required at the BSET and MSET pins to produce the desired bias and modulation currents. This design example assumes that the resistance of the TOSA is 25 , the forward voltage of the laser at low current is VF = 1 V, IBIAS = 40 mA, IMOD = 60 mA, and VCC = 3.3 V. Headroom Calculations To ensure proper device operation, the voltages on the IBIAS, IMODP, and IMODN pins must meet the compliance voltage specifications in Table 1. Considering the typical application circuit shown in Figure 33, the voltage at the IBIAS pin can be written as VIBIAS = VCC - VF - (IBIAS x RTOSA) - VLA where: VCC is the supply voltage. VF is the forward voltage across the laser at low current. VCC - 0.75 > VCC - 1.1 V, which satisfies the requirement The maximum voltage at the modulation output pins is equal to VCC + (IMOD x 25)/2 = VCC + 0.75 VCC + 0.75 < VCC + 1.1 V, which satisfies the requirement Headroom calculations must be repeated for the minimum and maximum values of the required IBIAS and IMOD ranges to ensure proper device operation over all operating conditions. BSET and MSET Pin Voltage Calculation To set the desired bias and modulation currents, the BSET and MSET pins of the ADN2525 must be driven with the appropriate dc voltage. The voltage range required at the BSET pin to generate the required IBIAS range can be calculated using the BSET voltage to IBIAS gain specified in Table 1. Assuming that IBIAS = 40 mA and the typical IBIAS/VBSET ratio of 100 mA/V, the BSET voltage is given by RTOSA is the resistance of the TOSA. VBSET = VLA is the dc voltage drop across L5, L6, L7, and L8. VLB is the dc voltage drop across L1, L2, L3, and L4. For proper operation, the minimum voltage at the IBIAS pin should be greater than 0.6 V, as specified by the minimum IBIAS compliance specification in Table 1. Assuming that the voltage drop across the 25 transmission lines is negligible and that VLA = 0 V, VF = 1 V, and IBIAS = 40 mA, VIBIAS = 3.3 - 1 - (0.04 x 25) = 1.3 V IBIAS (mA) 100 mA/V = 40 = 0. 4 V 100 The BSET voltage range can be calculated using the required IBIAS range and the minimum and maximum BSET voltage to IBIAS gain values specified in Table 1. The voltage required at the MSET pin to produce the desired modulation current can be calculated using VMSET = IMOD K where K is the MSET voltage to IMOD ratio. VIBIAS = 1.3 V > 0.6 V, which satisfies the requirement The maximum voltage at the IBIAS pin must be less than the maximum IBIAS compliance specification as described by VCOMPLIANCE_MAX = VCC - 0.75 - 4.4 x IBIAS (A) The value of K depends on the actual resistance of the TOSA. It can be read using the plot shown in Figure 29. For a TOSA resistance of 25 , the typical value of K = 120 mA/V. Assuming that IMOD = 60 mA and using the preceding equation, the MSET voltage is given by For this example: VCOMPLIANCE_MAX = VCC - 0.75 - 4.4 x 0.04 = 2.53 V VMSET = IMOD (mA) 120 mA/V = 60 = 0. 5 V 120 VIBIAS = 1.3 V < 2.53 V, which satisfies the requirement To calculate the headroom at the modulation current pins (IMODP and IMODN), the voltage has a dc component equal to VCC due to the ac-coupled configuration and a swing equal to IMOD x 25 . For proper operation of the ADN2525, the voltage at each modulation output pin should be within the normal operation region shown in Figure 30. The MSET voltage range can be calculated using the required IMOD range and the minimum and maximum K values. These can be obtained from the minimum and maximum curves in Figure 29. Rev. A | Page 14 of 16 ADN2525 OUTLINE DIMENSIONS 3.00 BSC SQ 0.60 MAX 0.45 PIN 1 INDICATOR TOP VIEW 13 12 2.75 BSC SQ 0.80 MAX 0.65 TYP 12 MAX SEATING PLANE 16 1 EXPOSED PAD 0.50 BSC 0.90 0.85 0.80 0.50 0.40 0.30 PIN 1 INDICATOR *1.65 1.50 SQ 1.35 9 (BOTTOM VIEW) 4 8 5 0.25 MIN 1.50 REF 0.05 MAX 0.02 NOM 0.30 0.23 0.18 0.20 REF *COMPLIANT TO JEDEC STANDARDS MO-220-VEED-2 EXCEPT FOR EXPOSED PAD DIMENSION. Figure 34. 16-Lead Lead Frame Chip Scale Package [LFCSP_VQ] 3 mm x 3 mm Body, Very Thin Quad (CP-16-3) Dimensions shown in millimeters ORDERING GUIDE Model ADN2525ACPZ-WP 1 ADN2525ACPZ-R21 ADN2525ACPZ-REEL71 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C Package Description 16-Lead LFCSP_VQ, 50-Piece Waffle Pack 16-Lead LFCSP_VQ, 250-Piece Reel 16-Lead LFCSP_VQ, 7" 1,500-Piece Reel Z = Pb-free part. Rev. A | Page 15 of 16 Package Option CP-16-3 CP-16-3 CP-16-3 Branding F06 F06 F06 ADN2525 NOTES (c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05077-0-8/06(A) T T Rev. A | Page 16 of 16