IS43/46TR16640A/AL, IS43/46TR81280A/AL 128Mx8, 64Mx16 1Gb DDR3 SDRAM ADVANCED INFORMATION DECEMBER 2011 FEATURES Standard Voltage: VDD and VDDQ = 1.5V 0.075V Low Voltage (L): VDD and VDDQ = 1.35V + 0.1V, -0.067V Refresh Interval: 7.8 us (8192 cycles/64 ms) Tc= -40C to 85C 3.9 us (8192 cycles/32 ms) Tc= 85C to 105C High speed data transfer rates with system frequency up to 933 MHz 8 internal banks for concurrent operation 8Bits pre-fetch architecture Programmable CAS Latency: 5, 6, 7, 8, 9, 10 and 11 Programmable Additive Latency: 0, CL-1,CL-2 Programmable CAS WRITE latency (CWL) based on tCK Programmable Burst Length: 4 and 8 Programmable Burst Sequence: Sequential or Interleave BL switch on the fly Auto Self Refresh(ASR) Self Refresh Temperature(SRT) OPTIONS Configuration: 128Mx8 64Mx16 Package: 96-ball FBGA (9mm x 13mm) for x16 78-ball FBGA (8mm x 10.5mm) for x8 Partial Array Self Refresh Asynchronous RESET pin TDQS (Termination Data Strobe) supported (x8 only) OCD (Off-Chip Driver Impedance Adjustment) Dynamic ODT (On-Die Termination) Driver strength : RZQ/7, RZQ/6 (RZQ = 240 ) Write Leveling Operating temperature: Commercial (TC = 0C to +95C) Industrial (TC = -40C to +95C) Automotive, A1 (TC = -40C to +95C) Automotive, A2 (TC = -40C to +105C) ADDRESS TABLE Parameter Row Addressing Column Addressing Bank Addressing Page size Auto Precharge Addressing BL switch on the fly 128Mx8 A0-A13 A0-A9 BA0-2 1KB A10/AP A12/BC# 64Mx16 A0-A12 A0-A9 BA0-2 2KB A10/AP A12/BC# SPEED BIN Speed Option JEDEC Speed Grade CL-nRCD-nRP tRCD,tRP(min) 187F 15G 15H 125J 125K 107K 107L DDR31066F 7-7-7 13.125 DDR31333G 8-8-8 12.0 DDR31333H 9-9-9 13.5 DDR31600J 10-10-10 12.5 DDR31600K 11-11-11 13.75 DDR31866K 11-11-11 11.77 DDR31866L 12-12-12 12.84 Units tCK ns Note: Faster speed options are backward compatible to slower speed options. Copyright (c) 2011 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 1 IS43/46TR16640A/AL, IS43/46TR81280A/AL 1. DDR3 PACKAGE BALLOUT 1.1 DDR3 SDRAM package ballout 78-ball FBGA - x8 1 VSS 2 VDD B VSS VSSQ C D VDDQ DQ2 VSSQ DQ6 E VREFDQ F NC1 G H J K VDD L VSS M VDD N VSS A 3 NC 4 5 6 7 NU/TDQS# 8 VSS 9 VDD DQ0 DM/TDQS VSSQ VDDQ DQS DQ1 DQ3 VSSQ DQS# VDD VSS VSSQ VDDQ DQ4 DQ7 DQ5 VDDQ VSS RAS# CK VSS NC ODT VDD CAS# CK# VDD CKE NC CS# WE# A10/AP ZQ NC VSS BA0 BA2 A15 VREFCA VSS A3 A0 A12/BC# BA1 VDD A5 A2 A1 A4 VSS A7 A9 A11 A6 VDD RESET# A13 NC/A14 A8 VSS Note: NC balls have no internal connection. NC/14 and NC/15 are one of NC pins and reserved for higher densities. 1.2 DDR3 SDRAM package ballout 96-ball FBGA - x16 A 1 VDDQ 2 DQU5 3 DQU7 VDD 4 5 6 7 DQU4 8 VDDQ 9 VSS VSS DQSU# DQU6 VSSQ VDDQ B VSSQ C D VDDQ DQU3 DQU1 DQSU DQU2 VSSQ VDDQ DMU DQU0 VSSQ VDD E VSS VSSQ DQL0 DML VSSQ VDDQ F VDDQ DQL2 DQSL DQL1 DQL3 VSSQ G VSSQ DQL6 DQSL# VDD VSS VSSQ H VREFDQ VDDQ DQL4 DQL7 DQL5 VDDQ J K NC VSS RAS# CK VSS NC ODT VDD CAS# CK# VDD CKE L NC CS# WE# A10/AP ZQ NC M VSS BA0 BA2 NC/A15 VREFCA VSS N A12/BC# BA1 VDD VDD A3 A0 P VSS A5 A2 A1 A4 VSS R T VDD A7 A9 A11 A6 VDD VSS RESET# NC/A13 NC/A14 A8 VSS Note: NC balls have no internal connection. NC/13, NC/14 and NC/15 are one of NC pins and reserved for higher densities. Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 2 IS43/46TR16640A/AL, IS43/46TR81280A/AL 1.3 Pinout Description - JEDEC Standard Symbol Type Function CK, CK# Input CKE, (CKE0), (CKE1) Input CS#, (CS0#), (CS1#), (CS2#), (CS3#) ODT, (ODT0), (ODT1) Input Clock: CK and CK# are differential clock inputs. All address and control input signals are sampled on the crossing of the positive edge of CK and negative edge of CK#. Clock Enable: CKE HIGH activates, and CKE Low deactivates, internal clock signals and device input buffers and output drivers. Taking CKE Low provides Precharge Power-Down and SelfRefresh operation (all banks idle), or Active Power-Down (row Active in any bank). CKE is asynchronous for Self-Refresh exit. After VREFCA and VREFDQ have become stable during the power on and initialization sequence, they must be maintained during all operations (including Self-Refresh). CKE must be maintained high throughout read and write accesses. Input buffers, excluding CK, CK#, ODT and CKE, are disabled during power-down. Input buffers, excluding CKE, are disabled during Self-Refresh. Chip Select: All commands are masked when CS# is registered HIGH. CS# provides for external Rank selection on systems with multiple Ranks. CS# is considered part of the command code. RAS#. CAS#. WE# DM, (DMU), (DML) Input BA0 - BA2 Input A0 - A13 Input A10 / AP Input A12 / BC# Input RESET# Input DQ Input / Output DQU, DQL, DQS, DQS#, DQSU, DQSU#, DQSL, DQSL# Input / Output TDQS, TDQS# Output Input Input NC On Die Termination: ODT (registered HIGH) enables termination resistance internal to the DDR3 SDRAM. When enabled, ODT is only applied to each DQ, DQSU, DQSU#, DQSL, DQSL#, DMU, and DML signal. The ODT pin will be ignored if MR1 and MR2 are programmed to disable RTT. Command Inputs: RAS#, CAS# and WE# (along with CS#) define the command being entered. Input Data Mask: DM is an input mask signal for write data. Input data is masked when DM is sampled HIGH coincident with that input data during a Write access. DM is sampled on both edges of DQS. For x8 device, the function of DM or TDQS/TDQS# is enabled by Mode Register A11 setting in MR1. Bank Address Inputs: BA0 - BA2 define to which bank an Active, Read, Write, or Precharge command is being applied. Bank address also determines which mode register is to be accessed during a MRS cycle. Address Inputs: Provide the row address for Active commands and the column address for Read/ Write commands to select one location out of the memory array in the respective bank. (A10/AP and A12/BC# have additional functions; see below). The address inputs also provide the op-code during Mode Register Set commands. Auto-precharge: A10 is sampled during Read/Write commands to determine whether Autoprecharge should be performed to the accessed bank after the Read/Write operation. (HIGH: Autoprecharge; LOW: no Autoprecharge). A10 is sampled during a Precharge command to determine whether the Precharge applies to one bank (A10 LOW) or all banks (A10 HIGH). If only one bank is to be precharged, the bank is selected by bank addresses. Burst Chop: A12 / BC# is sampled during Read and Write commands to determine if burst chop (on-the-fly) will be performed. (HIGH, no burst chop; LOW: burst chopped). See command truth table for details. Active Low Asynchronous Reset: Reset is active when RESET# is LOW, and inactive when RESET# is HIGH. RESET# must be HIGH during normal operation. RESET# is a CMOS rail- torail signal with DC high and low at 80% and 20% of VDD, i.e., 1.20V for DC high and 0.30V for DC low. Data Input/ Output: Bi-directional data bus. Data Strobe: output with read data, input with write data. Edge-aligned with read data, centered in write data. For the x16, DQSL corresponds to the data on DQL0-DQL7; DQSU corresponds to the data on DQU0-DQU7. The data strobes DQS, DQSL, and DQSU are paired with differential signals DQS#, DQSL#, and DQSU#, respectively, to provide differential pair signaling to the system during reads and writes. DDR3 SDRAM supports differential data strobe only and does not support single-ended. Termination Data Strobe: TDQS/TDQS# is applicable for x8 DRAMs only. When enabled via Mode Register A11 = 1 in MR1, the DRAM will enable the same termination resistance function on TDQS/TDQS# that is applied to DQS/DQS#. When disabled via mode register A11 = 0 in MR1, DM/TDQS will provide the data mask function and TDQS# is not used. x16 DRAMs must disable the TDQS function via mode register A11 = 0 in MR1. No Connect: No internal electrical connection is present. VDDQ Supply DQ Power Supply: 1.5 V +/- 0.075 V for standard voltage or 1.35V +0.1V, -0.067V for low voltage VSSQ Supply DQ Ground Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 3 IS43/46TR16640A/AL, IS43/46TR81280A/AL VDD Supply Power Supply: 1.5 V +/- 0.075 V for standard voltage or 1.35V +0.1V, -0.067V for low voltage VSS Supply Ground VREFDQ Supply Reference voltage for DQ VREFCA Supply Reference voltage for CA ZQ, (ZQ0), (ZQ1), (ZQ2), (ZQ3) Supply Reference Pin for ZQ calibration Input only pins (BA0-BA2, A0-A13, RAS#, CAS#, WE#, CS#, CKE, ODT, and RESET#) do not supply termination. Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 4 IS43/46TR16640A/AL, IS43/46TR81280A/AL ORDERING INFORMATION 64Mx16 - Commercial Range: (0C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 1333MT/s 7-7-7 8-8-8 IS43TR16640A -187FBL IS43TR16640A -15GBL 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 1333MT/s 1600MT/s 1600MT/s 9-9-9 10-10-10 11-11-11 IS43TR16640A -15HBL IS43TR16640A -125JBL IS43TR16640A -125KBL 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 64Mx16 - Industrial Range: (-40C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 1333MT/s 1333MT/s 7-7-7 8-8-8 9-9-9 IS43TR16640A -187FBLI IS43TR16640A -15GBLI IS43TR16640A -15HBLI 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 1600MT/s 1600MT/s 10-10-10 11-11-11 IS43TR16640A -125JBLI IS43TR16640A -125KBLI 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 64Mx16 - Automotive, A1 Range: (-40C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 1333MT/s 1333MT/s 1600MT/s 1600MT/s 7-7-7 8-8-8 9-9-9 10-10-10 11-11-11 IS46TR16640A -187FBLA1 IS46TR16640A -15GBLA1 IS46TR16640A -15HBLA1 IS46TR16640A -125JBLA1 IS46TR16640A -125KBLA1 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 64Mx16 - Automotive, A2 Range: (-40C TC 105C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 1333MT/s 1333MT/s 1600MT/s 1600MT/s 7-7-7 8-8-8 9-9-9 10-10-10 11-11-11 IS46TR16640A -187FBLA2 IS46TR16640A -15GBLA2 IS46TR16640A -15HBLA2 IS46TR16640A -125JBLA2 IS46TR16640A -125KBLA2 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free 96-ball FBGA,Lead-free Note: Contact ISSI for availability of options. Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 5 IS43/46TR16640A/AL, IS43/46TR81280A/AL ORDERING INFORMATION 128Mx8 - Commercial Range: (0C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 7-7-7 IS43TR81280A -187FBL 78-ball FBGA,Lead-free 1333MT/s 8-8-8 IS43TR81280A -15GBL 78-ball FBGA,Lead-free 1333MT/s 9-9-9 IS43TR81280A -15HBL 78-ball FBGA,Lead-free 1600MT/s 10-10-10 IS43TR81280A -125JBL 78-ball FBGA,Lead-free 1600MT/s 11-11-11 IS43TR81280A -125KBL 78-ball FBGA,Lead-free 128Mx8 - Industrial Range: (-40C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 7-7-7 IS43TR81280A -187FBLI 78-ball FBGA,Lead-free 1333MT/s 8-8-8 IS43TR81280A -15GBLI 78-ball FBGA,Lead-free 1333MT/s 9-9-9 IS43TR81280A -15HBLI 78-ball FBGA,Lead-free 1600MT/s 10-10-10 IS43TR81280A -125JBLI 78-ball FBGA,Lead-free 1600MT/s 11-11-11 IS43TR81280A -125KBLI 78-ball FBGA,Lead-free 128Mx8 - Automotive, A1 Range: (-40C TC 95C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 7-7-7 IS46TR81280A -187FBLA1 78-ball FBGA,Lead-free 1333MT/s 8-8-8 IS46TR81280A -15GBLA1 78-ball FBGA,Lead-free 1333MT/s 9-9-9 IS46TR81280A -15HBLA1 78-ball FBGA,Lead-free 1600MT/s 10-10-10 IS46TR81280A -125JBLA1 78-ball FBGA,Lead-free 1600MT/s 11-11-11 IS46TR81280A -125KBLA1 78-ball FBGA,Lead-free 128Mx8 - Automotive, A2 Range: (-40C TC 105C) Data Rate CL-tRCD-tRP Order Part No. Package 1066MT/s 7-7-7 IS46TR81280A -187FBLA2 78-ball FBGA,Lead-free 1333MT/s 8-8-8 IS46TR81280A -15GBLA2 78-ball FBGA,Lead-free 1333MT/s 9-9-9 IS46TR81280A -15HBLA2 78-ball FBGA,Lead-free 1600MT/s 10-10-10 IS46TR81280A -125JBLA2 78-ball FBGA,Lead-free 1600MT/s 11-11-11 IS46TR81280A -125KBLA2 78-ball FBGA,Lead-free Note: Contact ISSI for availability of options. Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 6 IS43/46TR16640A/AL, IS43/46TR81280A/AL PACKAGE OUTLINE DRAWING 78-ball BGA (8mm x 10.5mm): 0.8mm x 0.8mm Pitch (x8) Bottom View 6.40 Max. 1.20 Min. 0.25 Max. 0.40 9.60 10.50 +/- 0.10 0.8 0.8 Min 0.1 Min 0.1 8.00 +/- 0.10 Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 78 x o Min. 0.40 Max. 0.50 7 IS43/46TR16640A/AL, IS43/46TR81280A/AL PACKAGE OUTLINE DRAWING 96-ball BGA (9mm x 13mm): 0.8mm x 0.8mm Pitch (x16) Max. 1.20 Bottom View Min. 0.25 Max. 0.40 6.40 12.00 13.00 +/- 0.10 0.8 0.8 Min 0.1 Min 0.1 9.00 +/- 0.10 Integrated Silicon Solution, Inc. - www.issi.com - Rev. 00A 12/12/2011 96 x o Min. 0.40 Max. 0.50 8