SD-150 150W Single Output DC-DC Converter series Features : 2:1 wide input range Protections: Short circuit / Overload / Over voltage 1500VAC I/O isolation Built-in EMI filter, low ripple noise 100% full load burn-in test 24V and 48V input voltage design refer to LVD Low cost High reliability 2 years warranty (for D type only) SPECIFICATION MODEL SD-150B-12 SD-150C-12 SD-150D-12 12V 24V RATED CURRENT 12.5A 6.3A CURRENT RANGE 0 ~ 12.5A 0 ~ 6.3A RATED POWER 150W 151.2W RIPPLE & NOISE (max.) Note.2 120mVp-p OUTPUT INPUT VOLTAGE ADJ. RANGE 1.0% 1.0% 0.5% 0.3% LOAD REGULATION 0.5% 0.3% SETUP, RISE TIME 2s, 50ms(only D mode) at full load HOLD UP TIME (Typ.) 24ms(only D mode) at full load VOLTAGE RANGE B:19 ~ 36VDC EFFICIENCY (Typ.) 75% 77% 79% 77% 80% 82% DC CURRENT (Typ.) INRUSH CURRENT (Typ.) 6.8A/24V D:22.5A/96VDC 3.4A/48V 2.7A/96V 6.8A/24V 3.4A/48V 2.7A/96V LEAKAGE CURRENT <0.75mA / 120VAC (SD-150D) OVERLOAD 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE OTHERS C:36 ~ 72VDC D:72 ~144VDC or 85 ~ 132VAC 16.8V ~ 20V/10% LOAD 31.5 ~ 37.5V/10% LOAD Protection type : Hiccup mode, recovers automatically after fault condition is removed -10 ~ +60 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes IEC60950-1 CB approved by TUV (for D type only) I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B / 70% RH EMS IMMUNITY Compliance to EN61000-4-2,3,4,6,8; ENV50204, light industry level, criteria A MTBF 296.2K hrs min.(SD-150B) 289.9K hrs min.(SD-150C) 199*110*50mm (L*W*H) 0.86Kg; 16pcs/14.5Kg/0.95CUFT DIMENSION PACKING NOTE SD-150D-24 23 ~ 30VDC LINE REGULATION OVER VOLTAGE (Note 4) SD-150C-24 150mVp-p 11 ~ 16VDC VOLTAGE TOLERANCE Note.3 PROTECTION EMC SD-150B-24 DC VOLTAGE 289K Hrs min.(SD-150D) MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SD-150-SPEC 2010-07-27 http://store.iiic.cc/ SD-150 150W Single Output DC-DC Converter Mechanical Specification Case No. 906 series Unit:mm 192 5 172 3.5 12 6 100 1 9.5 2 3 97 110 4 8.2 5 6 5-M3 37 7 Terminal Pin No. Assignment Pin No. 1,2 3 199 6 6.5 3.5 50 3M3 20 Pin No. 4,5 6,7 Assignment DC OUTPUT -V DC OUTPUT +V SD-150B,C Pin No. Assignment DC INPUT V+ 1 2 DC INPUT V- 20 12 24.5 3.5 25 16.5 190.5 Assignment INPUT FG SD-150D Pin No. Assignment AC/DC INPUT 1,2 159 Block Diagram fosc : 83KHz RECTIFIERS & FILTER EMI FILTER I/P FILTER RECTIFIERS & FILTER POWER SWITCHING +V -V (ONLY D SERIES) FG O.V.P. O.L.P. DETECTION CIRCUIT PWM CONTROL Static Characteristics (24V) Derating Curve OUTPUT VOLTAGE (V) SD-150C,D-24 100 80 SD-150B-24 SD-150C,D-12 LOAD (%) 60 SD-150B-12 40 20 -10 -10 0 0 10 20 30 40 50 45 60 55 350 28 300 24 250 20 200 16 150 12 100 8 50 (VERTICAL) (HORIZONTAL) AMBIENT TEMPERATURE ( ) 80 85 90 95 100 105 110 115 120 125 OUTPUT RIPPLE (mVp-p) Ta=25 32 130 INPUT VOLTAGE (V) File Name:SD-150-SPEC 2010-07-27 http://store.iiic.cc/