Photo IC
Publication date : August 2007 SHE00052BED 1
PNA4701M
Photodiode with amplier functions
For infrared remote control systems
Features
Center frequency fO : 36.7 kHz
Operating supply voltage VCC : 3.3 V(typ.)
Adoption of visible light cutoff resin
Absolute Maximum Ratings Ta = 25°C
Parameter Symbol Rating Unit
Operating supply voltage VCC 0.5 to +5 V
Power dissipation PD200 mW
Operating ambient temperature Topr 15 to +70 °C
Storage temperature Tstg 40 to +100 °C
Soldering temperature *Tsol 260 °C
Note) *: Less than 5 s
Electrical Characteristics Ta = 25°C±3°C, VCC = 3.3 V
Parameter Symbol Conditions Min Typ Max Unit
Operating supply voltage VCC 2.7 3.3 3.6 V
Output voltage low-level *2VOL L 7 m, IOL = 400 µA 0.1 0.3 V
Output voltage high-level VOH No signal condition, IOH = –2 µA 2.86 3.3 V
Supply current ICC 0.6 0.8 1.0 mA
Maximum reception distance Lmax 7.0 m
Pulse width low-level *1TWL L = 0.1 m to 7 m, 16 pulse 200 400 600 ms
Pulse width high-level *1TWH
Center frequency fO36.7 kHz
Note) 1. Measuring methods are based on JAPANESE INDUSTRIAL STANDARD JIS C 7031 measuring methods for diodes.
2. *1: Burst wave form Figure 1
*2: Constant wave form Figure 2
400 µs400 µs
Carrier frequency: fOCarrier frequency: fO
Figure 2Figure 1
Unit: mm
1: VO
2: GND
3: VCC
(5°)
(5°)
(5°)
(5°)
7.0±0.2
(3.5)
5.25±0.3
(2.25)
1.5max.
R2.25±0.1
3-1.5±0.2
3-0.5
(2-2.54)
123
Not soldered 1.5
8.0±0.2
(5.2)
(2.3)
22.0 min.
(0.8)
0.3 max.
+0.25
-
0.15
2.0±0.15
1.0±0.15
0.3 max.
3-0.45+0.25
-
0.15
This product complies with the RoHS Directive (EU 2002/95/EC).
Maintenance/
Discontinued
Maintenance/Discontinued includes following four Product lifecycle stage.
planed maintenance type
maintenance type
planed discontinued typed
discontinued type
Please visit following URL about latest information.
http://www.semicon.panasonic.co.jp/en/
PNA4701M
2 SHE00052BED
Block Diagram
VO
GND
PD
AGC
VCC
Controler
Comparator
RL
(100 k)
Integrator
BPF DemodulatorAmplifier
Panasonic Transmitter Specications
GND
10 V
PNZ323B
20 cm
10 k
10 k
10 k
10 µF
VO
VO 55 mV
LED transmitter unit Standard receiver unit
1. The output of the LED transmitter unit is adjusted so that the output standard receiver unit, VO may be 55 mV when transmitting
waves (duty = 50%) are output from the transmitter unit, where the sensitivity to infrared emitters (SIR) of PNZ323B is 0.53 mA when
the irradiance H is 12.45 mW/cm2.
2. The maximum detection distance of this specification is guaranteed by TWH and TWL being within the limits when constant 16 pulses
are transmitted with the output of the transmitter unit corresponded to the maximum detection distance in the system above.
(The maximum detection distance is measured in the darkness without disturbing noises.)
This product complies with the RoHS Directive (EU 2002/95/EC).
Maintenance/
Discontinued
Maintenance/Discontinued includes following four Product lifecycle stage.
planed maintenance type
maintenance type
planed discontinued typed
discontinued type
Please visit following URL about latest information.
http://www.semicon.panasonic.co.jp/en/
PNA4701M
SHE00052BED 3
Lmax Ta BPF frequency characteristics Spectral sensitivity characteristics
Directivity characteristics
Ambient temperature Ta (°C)
Relative reception distance
Lmax (%)
120
100
80
60
40
20
00 20 40 60 80 100
20
VCC = 3.3 V
Transmitter: Standard LED
Transmission unit used
100
80
60
40
20
35 39 434137
033
Carrier frequency (kHz)
Relative sensitivity S (%)
100
80
60
20
40
700 900 1
200800 1
000 1
100
0
600
Wavelength λ (nm)
Relative sensitivity S (%)
0°10°20°
30°
40°
50°
60°
70°
80°
90°
20
100
80
60
40
Relative sensitivity S (%)
This product complies with the RoHS Directive (EU 2002/95/EC).
Maintenance/
Discontinued
Maintenance/Discontinued includes following four Product lifecycle stage.
planed maintenance type
maintenance type
planed discontinued typed
discontinued type
Please visit following URL about latest information.
http://www.semicon.panasonic.co.jp/en/
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1)If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2)The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3)The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
Any applications other than the standard applications intended.
(4)The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5)When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6)Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7)This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
Electric Industrial Co., Ltd.
This product complies with the RoHS Directive (EU 2002/95/EC).
Maintenance/
Discontinued
Maintenance/Discontinued includes following four Product lifecycle stage.
planed maintenance type
maintenance type
planed discontinued typed
discontinued type
Please visit following URL about latest information.
http://www.semicon.panasonic.co.jp/en/