4：OUT
1：VDD
3：PDN
Switch
Dynamic
OffsetCancellation
2：VSS
Output
Stage
Latch
Logic
AMP
Chopper
SW
Hall
Element
OSC
&
TimingLogic
Schmitt
Trigger
SorN
NorS NS 0
H
BopBrp
Bh
VOH
VOL
L
VOUT
Packagetop
Packagebottom
Magneticfluxdensity
●FunctionalBlockDiagram
●OperationalCharacteristics
Item
OSC
TimingLogic

HallElement
ChopperSW
AMP
SchmittTrigger
Generatesoperatingclock
GeneratestimingsignalrequiresforChopperSW,
AMPandothercircuits
HallelementfabricatedbyCMOSprocess
Performschoppinginordertocanceltheoffset
voltageofHallsensor
ReduceoffsetvoltageandamplifiesHalloutputvoltage
Hysteresiscomparator
CMOSoutput,Duringthepowerdownmode,output
islatchedinitspreviousstate
Function
LatchLogic
OutputStage
17
MonolithicHallEffectICs AK-series
●Features
・PrecisionBipolarHallEffectLatch
・Powermanageabilitythrough"PDN"pin
 CurrentconsumptioninPowerdownmodeislessthan1μA
・Lowcurrentconsumptionatactivemode:lessthanavg.
 150μA@VDD=3V
・UltrasmallSONpackage:1.1×1.4×t0.37mm,Halogenfree
AK8772
AK8772isultra-smallHalleffectICofasinglesiliconchipcomposedofHallelementandasignalprocessingIC.
SupplyVoltage
1.6〜5.5Ｖ
UltraHigh
Sensitivity
Bop：1.8mT
Output
CMOS
SON
Powerdown
Function
BipolarHall
EffectLatch
Shippedinpacket-tapereel(5000pcs/Reel)
Notice:Itisrequestedtoreadandaccept"IMPORTANTNOTICE"writtenonthebackofthefrontcoverofthiscatalogue.
IDD1
IDD2
IIN
VIH
VIL
VOH
VOL
TPD1
TPD2
TPD3
TPD4
TW
1
150
1
0.3
0.4
（36.6）
100
60
ー1
0.7VDD
VDDー0.4
100
μA
μA
μA
V
V
V
V
μs
μs
μs
1.5
36.6
1.0
24.4
0.5
12.2
ms
μs
PDN=0V
PDN=
VDD
,Average
IOUT
IOUT
=ー0.5mA
=＋0.5mA
＊
Active→PDN
PDN→Active
WhenPDN＝VDD
VDD
VDD
IOUT
VIN
IIN
TSTG
＋6.5
＋0.5
VDD＋0.3
＊
＋10
＋125
ー0.3
ー0.5
ー0.3
ー10
ー55
V
mA
V
mA
℃
OUT
PDN
PDN
Ta
5.5
＋85
3.01.6
ー30
V
℃
Bop
Brp
Bh
4.01.8
ー1.8
3.6
ー4.0
mT
mT
mT
Bop
Brp
Bh
4.21.8
ー1.8
3.6
ー4.2
mT
mT
mT
（Ta=25℃VDD =3.0V）
（Ta=25℃VDD =3.0V）
（Ta=−30〜＋85℃VDD =1.6〜5.5V）
●AbsoluteMaximumRatings
●RecommendedOperatingConditions
●ElectricalCharacteristics
●MagneticCharacteristics①
●MagneticCharacteristics②
Item
Min. Unit Notesymbol
Max.
Storagetemperature
Item Typ. Unitsymbol Min. Max.
Item Typ. Unitsymbol Min. NoteMax.
Item Typ. Unitsymbol Min. Max.
Item
Typ.
Unit
symbol
Min.
Max.
Outputcurrent
Input voltage
Input current
Power supply voltage
Operating temperature
Power supply voltage
Current consumption 2
PDNinputcurrent
PDNinputHvoltage
PDN input L voltage
High level output voltage
Lowleveloutputvoltage
PDN mode transition time 1
PDN mode transition time 2
Pulsedriveperiod
Pulse drive time
PDNH input pulse width
Current consumption 1
＊)
ThistransitiontimeisnotguaranteedbyinspectionbecausePDNinputtimingandinternaltimingareasynchronous
Releasing point
Hysteresis
Operating point
Releasing point
Hysteresis
Operating point
Note)ThespecificationsinMagneticCharacteristics②aredesigntargets.
＊)Lessthan+6.5V.
Note)Stressbeyondtheselistedvaluesmaycausepermanentdamagetothedevice.
18
•Please be aware that our products are not intended for use in life support equipment, devices, or systems. Use of our products in such applications requires the
advance written approval of our sales staff.
Certain applications using semiconductor devices may involve potential risks of personal injury, property damage or loss of life. In order to minimize these risks,
adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. Inclusion of our products in such
applications is understood to be fully at the risk of the customer using our devices or systems.
c
g
k
n
o
p
AK8772
t
t
t
t
VPDN［V］
VOUT［V］
IDD［mA］
B［mT］
0
0
NN
SS
Bop
Brp
0
0
T
PD
2
（＜100μs）
T
PD
4
（typ.24.4μs）
I
DD
2
（typ.2.5mA）
IDDOFF
IDD1
（<1μA）
T
PD
3
（typ.1ms）
T
PD
1
（＜36.6μs）
1.10 0.80
0.50
0.22
0.60
1.40
1.70
0.35
0.22
0.50
1.00
(0.125)
0.37
(0.23)
0.20
1.40
0.80
0.60
SensorCenter
Bop
Brp
VPDN［V］
VOUT
［V］
IDD
［mA］
B［mT］
Undefined
TPD2
（＜100μs）
t
t
t
t
0
N
0
0
0
S
TPD2
（＜100μs）
TPD1
（＜36.6μs）
TPD1
（＜36.6μs）
No.
1
2
3
4
Pinname
VDD
VSS
PDN
OUT
Function
Powersupply
Ground
Powerdown
H:Deviceactive
L:Devicepowerdown
Output
Note
CMOSInput.Thispinhastobe
tiedtoHlevelwhenexternal
powercontrolisnotused.
CMOSOutput
●Package（Unit:mm)
※Note1)Sensitiveareapositionreferencedto
thecenterofpackagewithinφ0.3mmcircle.
Note2)Tolerancesofdimensionotherwisenotedis
±0.05mm.
Note3)Hatchedareaisplated.
Note4)Centerpadarea(TAB)shouldbetiedtothe
VSSorfloating
●Footprint（forreference)
●FunctionTimingChart
Note1)Duringpowerdownmode,outputislatchedinits
previousstate.
Note2)WhenVDDissupplied,thetimefromreachingVDD=
1.6VtotheupdateoftheoutputstateisequaltoTPD2.
WhenPDNpinsettoLfromHduringsamplingisperforming,
thedevicetransitstopowerdownmodeaftersamplingiscompleted.
AndwhenPDNpinsettoLfromHwhilesamplingisnot
performing,thedevicetransitstopowerdownmodeimmediately.
FunctionalTiming Functionaltimingchart(detail)
19
AK8772
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
0
-1
-2
-3
-4
1
2
3
4
0
-1
-2
-3
-4
1
2
3
4
Bop
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
Brp
Bop,Brp［mT］
Bop,Brp［mT］
AmbientTemperatureTa［℃］
Bop,Brpvs.Ta(VDD=1.6V)
AmbientTemperatureTa［℃］
Bop,Brpvs.Ta(VDD =3.0V)
GND
VDD =3.0V
0.1μF
VDD
PDN
VSS
AK8772
OUT
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
0
-1
-2
-3
-4
1
2
3
4
0
-1
-2
-3
-4
1
2
3
4
Bop
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
Brp
Bop,Brp［mT］
Bop,Brp［mT］
AmbientTemperatureTa［℃］
Bop,Brpvs.Ta(VDD=2.0V)
AmbientTemperatureTa［℃］
Bop,Brpvs.Ta(VDD =5.5V)
-30 -20 -10 0 10 20 30 40 50 60 70 80 90
0
20
40
60
80
100
120
0
20
40
60
80
100
120
1 2 3 4 5 6
IDD2［μA］
IDD2［μA］
AmbientTemperatureTa［℃］
IDD2vs.Ta(invariousVDD)
VDD
［V］
IDD2vs.VDD(invariousTa)
85℃
25℃
0℃
-30℃
Bop
Brp
Bop
Brp
VDD=5.5V
VDD=3.0V
VDD=2.0V
VDD=1.6V
●TypicalCharacteristicData(forreference)
●ApplicationCircuit
CMOSOutput
CMOSInput 20
c
g
k
n
o
p
AK8772
IMPORTANT NOTICE
These products and thei r specifications are subject to change without notice.
When you consider any use or application of these products, please make
inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or
authorized distributors as to current status of the products.
Descriptions of external circuits, application circuits, sof tware and ot her related
information contained in this document are provided only to illustrate the
operation and application examples of the semiconductor products. You are
fully responsible for the incorporation of these external circuits, application
circuits, software and other related information in the design of your
equipments. AKM assumes no responsibility for any losses incurred by you or
third parties arising from th e use of these information herein. AKM assumes no
liability for infringement of any patent, intellectual property, or other rights in
the application or use of such information contained herein.
Any export of these products, or devices or systems containing them, may
require an export license or other official approval under the law and
regulations of the country of export pertaining to customs and tariffs, currency
exchange, or strategic materials.
AKM products are neither intended nor authorized for use as critical
componentsNote1) in any safety, life support, or other hazard related device or
systemNote2), and AKM assumes no responsibility for such use, except for the
use approved with the express written consent by Representative Director of
AKM. As used here:
Note1) A critical component is one whose failure to function or perform
may reasonably be expected to result, whether directly or indirectly, in the
loss of the safety or effectiveness of the device or system containing it,
and which must therefore meet very high standards of performance and
reliability.
Note2) A hazard related device or system is one designed o r intended fo r
life support or maintenance of safety or for applications in medicine,
aerospace, nuclear energy, or other fields, in which its failure to function
or perform may reasonably be expected to result in loss of life or in
significant injury or damage to person or property.
It is the responsibility of the buyer or distributor of AKM products, who
distributes, disposes of, or otherwise places the product with a third party, to
notify such third party in advance of the above conten t and conditions, and th e
buyer or distributor agrees to assume any and all responsibility and liability for
and hold AKM harmless from any and all claims arising from the use of said
product in the absence of such notification.
February 21, 2013