6AV6573-1EB06-0AE0 - SIEMENS

Preface

Overview

Safety notes and general

information

Plan deployment

Installation and connection

Operating elements and

indicators

Operating system and

configuration

Prepare and backup project

Runtime functionalities of a

project

Operating a project

Operating recipes

Maintenance/Service

Technical Specifications

Appendix

Abbreviations

Glossary

SIMATIC HMI

HMI device

MP 370 (WinCC flexible)

Operating Instructions

Edition 03/2004

A5E00280680-01

Order No. 6AV6691-1DE01-0AB0

Safety Guidelines

This manual contains notices which you should observe to ensure your own personal safety as well as to avoid

property damage. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring to property damage only have no safety alert symbol.

Danger

indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Warning

indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Caution

used with the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Caution

used without safety alert symbol indicates a potentially hazardous situation which, if not avoided, may

result in property damage.

Notice

used without the safety alert symbol indicates a potential situation which, if not avoided, may result in

an undesirable result or state.

When several danger levels apply, the notices of the highest level (lower number) are always displayed. If a

notice refers to personal damages with the safety alert symbol, then another notice may be added warning of

property damage.

Qualified Personnel

The device/system may only be set up and operated in conjunction with this documentation. Only qualified

personnel should be allowed to install and work on the equipment. Qualified persons are defined as persons who

are authorized to commission, to earth, and to tag circuits, equipment and systems in accordance with

established safety practices and standards.

Intended Use

Please note the following:

Warning

This device and its components may only be used for the applications described in the catalog or

technical description, and only in connection with devices or components from other manufacturers

approved or recommended by Siemens.

This product can only function correctly and safely if it is transported, stored, set up and installed

correctly, and operated and maintained as recommended.

Trademarks

All designations marked with ® are registered trademarks of Siemens AG. Other designations in this

documentation might be trademarks which, if used by third parties for their purposes, might infringe upon the

rights of the proprietors.

Reproduction, transmission or use of this document or its contents is not permitted without

express written authority. Offenders will be liable for damages. All rights, including rights

created by patent grant or registration of a utility model or design, are reserved.

Disclaimer of Liability

We have checked the contents of this manual for agreement with the hardware and

software described. Since deviations cannot be precluded entirely, we cannot guarantee

full agreement. However, the data in the manual are reviewed regularly, and any

necessary corrections will be included in subsequent editions. Suggestions for

improvement are welcomed.

Siemens AG

Automation and Drives Group

P.O. Box 4848, D-90327 Nuremberg (Germany)

Technical data subject to change

Siemens Aktiengesellschaft 6AV6691-1DE01-0AB0

이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다.

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 i

Preface

Purpose of this manual

This manual provides information based on the requirements defined by DIN 8418 regarding

mechanical engineering documentation. This information relates to the device, its place of

use, transport, storage, installation, use and maintenance.

This manual is intended for the following target groups:

• User

• Commissioning engineers

• Service technicians

• Maintenance technicians

Please read carefully the section "Safety information and general notes".

The help integrated in WinCC flexible, the WinCC flexible Information System, contains

detailed information. The Information System contains instructions, examples and reference

information in electronic form.

Basic knowledge required

A general knowledge of automation technology and process communication is necessary in

order to understand the manual.

It is assumed users have good basic knowledge on the use of personal computers and MS

Windows operating systems.

Area of validity

The manual applies to SIMATIC MP 370 in connection with the WinCC flexible 2004

software packet.

What's new since the 09/2002 release?

This manual describes the use of the HMI device in combination with WinCC flexible 2004.

The 09/2002 version is still valid for use of the HMI device with ProTool.

Its place in the information landscape

This manual is part of the SIMATIC HMI documentation. The information below presents an

overview of the information landscape of SIMATIC HMI.

User manual

• WinCC flexible Micro:

Preface

MP 370 (WinCC flexible)

ii Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

– Describes basics of configuration using the WinCC flexible Micro engineering system.

• WinCC flexible Compact/Standard/Advanced:

– Describes basic principles of configuration using the WinCC flexible Compact

Engineering System/WinCC flexible Standard/WinCC flexible Advanced

• WinCC flexible Runtime:

– Describes how to commission and operate your Runtime project on a PC.

• WinCC flexible Migration:

– Describes how to migrate an existing ProTool project to WinCC flexible.

– Describes how to migrate an existing WinCC project to WinCC flexible.

– Describes the conversion of ProTool projects together with changing the HMI device

from OP7 to OP 77B.

– Describes the conversion of ProTool projects with a change in the HMI device from a

graphics device to a Windows CE device.

• Communication:

– Communication Part 1 describes the connection of the HMI device to SIMATIC PLCs.

– Communication part 2 describes the integration of the HMI device into control systems

of third-party suppliers.

Operating instructions

• Operating instructions for the SIMATIC OP 77B,

TP 170micro/TP 170A/TP 170B/OP 170B, SIMATIC Mobile Panel 170, SIMATIC

TP 270/OP 270/MP 270B, and SIMATIC MP 370 HMI devices.

• Quick reference manuals for the SIMATIC OP 77B and SIMATIC Mobile Panel 170 HMI

devices.

Getting started

• WinCC flexible for newcomers:

– Based on a practical example, this is a step-by-step introduction to the basics of

configuring screens, alarms, recipes and screen navigation.

• WinCC flexible for advanced users:

– Based on a practical sample project, this is a step-by-step introduction to the basics of

engineering log files, project reports, scripts, user management, multilingual projects

and integration into STEP 7.

• WinCC flexible Options:

– Based on a practical sample project, this is a step-by-step introduction to the basics of

configuring the options WinCC flexible Sm@rtServices, Sm@rtAccess and OPC

Server.

Online availability

The following links provide direct access to technical documentation on SIMATIC products

and systems in English, German, French, Italian, and Spanish.

• SIMATIC Guide for Technical Documentation in German:

http://www.ad.siemens.de/simatic/portal/html_00/techdoku.htm

• SIMATIC Guide for Technical Documentation in English:

http://www.ad.siemens.de/simatic/portal/html_76/techdoku.htm

Preface

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 iii

Conventions

A distinction was made in naming configuration and runtime software:

• "WinCC flexible" refers to the configuration software.

• "Runtime" refers to the runtime software that can be executed on HMI devices.

The term "WinCC flexible" is used in the general context. A version name such as

"WinCC flexible 2004" is always used when it is necessary to distinguish it from other

versions.

The following conventions are intended to facilitate easy reading:

Layout Range of validity

"Add screen" • Terminology of the user interface, e.g. dialog names, tabs,

buttons, menu commands.

• Input required, e.g. limit values, tag values.

• Path specification

"File ? Edit" Operating sequence, e.g. menu / context menu commands.

<F1>, <Alt+P> Keyboard operation

Please observe the following emphasized notes:

Note

Notes containing important information about the product and its use or a specific section of

the documentation to which you should pay particular attention.

Trademarks

All names designated with an ® are registered trademarks of Siemens AG.

HMI®

SIMATIC®

SIMATIC HMI®

SIMATIC ProTool®

SIMATIC WinCC®

SIMATIC WinCC flexible®

SIMATIC MP 370®

The remaining product names in this publication may be trademarks and the use of these

names by third parties for their own purposes may violate the rights of the owner.

Further support

Representatives and offices

If you have any further questions relating to the products described in this manual, please

contact your local representative at the SIEMENS branch nearest you.

Preface

MP 370 (WinCC flexible)

iv Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

You local representative can be found under:

http://www.siemens.com/automation/partner

Training center

We offer relevant courses to simplify your introduction to the world of automation systems.

Please contact your regional training center, or the central training center in D-

90327 Nuremberg.

Phone: +49 (911) 895-3200

Internet: http://www.siemens.com/simatic

Service & Support on the Internet

Service & Support offers comprehensive information on SIMATIC products online at

"http://www.siemens.com/automation/service&support":

• The newsletter keeps you up-to-date with information relating to your products.

• Our Service & Support search engine provides you with abundant documentation.

• A bulletin board where users and experts exchange their knowledge worldwide.

• Current product information, FAQs and downloads.

• Your local contact for Automation & Drives.

• Information about on-site services, repairs, spare parts and much more is available on

our "Services" pages.

A&D Technical Support and Authorization

Available 24 hours worldwide:

Johnson City Nuremberg

Beijing

SIMATIC Hotline

Worldwide (Nuremberg)

Technical Support

(Free Contact)

Worldwide (Nuremberg)

Technical Support

(fee-based, only with Automation Value Card)

Preface

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 v

Local time:

Mon.–Fri. 07:00 a.m. to 5:00 p.m.

Telephone:

+49 (0) 180 5050-222

Fax:

+49 (0) 180 5050-223

E-Mail:

adsupport@siemens.com

GMT: +1:00

Local time:

0:00 to 24:00, 365 days

Telephone:

+49 (911) 895-7777

Fax:

+49 (911) 895-7001

E-mail: –

GMT: +1:00

Europe/Africa (Nuremberg)

Authorization

Local time:

Mon.–Fri. 07:00 a.m. to 5:00 p.m.

Telephone:

+49 (911) 895-7200

Fax:

+49 (911) 895-7201

E-Mail:

adauthorisierung@siemens.com

GMT: +1:00

America (Johnson City)

Technical Support and Authorization

Local time:

Mon.–Fri. 8:00 a.m. to 7:00 p.m.

Telephone:

+1 423 461-2522

Fax:

+1 423 461-2289

E-Mail:

simatic.hotline@sea.siemens.com

GMT: –5:00

Asia/Pacific (Beijing)

Technical Support and Authorization

Local time:

Mon.–Fri. 8:30 a.m. to 5:30 p.m.

Telephone:

+86 (10) 64 75 75 75

Fax:

+86 (10) 64 74 74 74

E-mail:

adsupport.asia@siemens.com

GMT: +8:00

Information is available in German and English.

Preface

MP 370 (WinCC flexible)

vi Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 vii

Table of contents

Preface ........................................................................................................................................................i

1 Overview................................................................................................................................................. 1-1

1.1 Multi Panel MP 370.................................................................................................................... 1-1

1.2 Area of use................................................................................................................................. 1-2

1.3 Configuring with WinCC flexible................................................................................................. 1-3

1.4 Features ..................................................................................................................................... 1-4

1.5 Functional scope........................................................................................................................ 1-5

1.6 Communication with PLCs......................................................................................................... 1-8

1.7 Options....................................................................................................................................... 1-9

1.7.1 Hardware options....................................................................................................................... 1-9

1.7.1.1 Backup battery ........................................................................................................................... 1-9

1.7.1.2 PC card / CF card .................................................................................................................... 1-10

1.7.2 Software options ...................................................................................................................... 1-12

1.7.2.1 Internet Explorer ...................................................................................................................... 1-12

2 Safety notes and general information ..................................................................................................... 2-1

2.1 Safety notes ............................................................................................................................... 2-1

2.2 General information ................................................................................................................... 2-1

3 Plan deployment..................................................................................................................................... 3-1

3.1 Transport.................................................................................................................................... 3-1

3.2 Electromagnetic compatibility .................................................................................................... 3-1

3.3 Installation locations and type of protection...............................................................................3-3

3.4 Producing the installation cut-out............................................................................................... 3-4

4 Installation and connection ..................................................................................................................... 4-1

4.1 Check shipment ......................................................................................................................... 4-1

4.2 Installation of the HMI device..................................................................................................... 4-1

4.2.1 Installation of the touch panel unit ............................................................................................. 4-2

4.3 Connecting the HMI device........................................................................................................ 4-3

4.3.1 Conditions .................................................................................................................................. 4-3

4.3.2 Interfaces ................................................................................................................................... 4-4

4.3.3 Connecting the potential equalization........................................................................................ 4-6

4.3.4 Connecting peripheral equipment.............................................................................................. 4-7

4.3.4.1 Connect printer........................................................................................................................... 4-7

4.3.4.2 Connect

external keyboard and mouse .....................................................................................4-9

4.3.5 Connecting the PLC................................................................................................................. 4-11

4.3.6 Connecting the configuration computer ................................................................................... 4-13

4.3.7 Connecting an uninterruptible power supply (UPS)................................................................. 4-14

4.3.8 Connecting the power supply................................................................................................... 4-15

Table of contents

MP 370 (WinCC flexible)

viii Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4.4 Switch on and test the HMI device........................................................................................... 4-16

5 Operating elements and indicators ......................................................................................................... 5-1

5.1 Front view MP 370 Touch .......................................................................................................... 5-1

5.2 Front view MP 370 Key.............................................................................................................. 5-2

5.2.1 Key pads .................................................................................................................................... 5-2

5.2.2 Function keys ............................................................................................................................. 5-4

5.2.3 System keys............................................................................................................................... 5-5

5.2.4 Labeling the softkeys ................................................................................................................. 5-6

5.3 Operation with external keyboard/mouse .................................................................................. 5-9

6 Operating system and configuration ....................................................................................................... 6-1

6.1 HMI device loader ...................................................................................................................... 6-1

6.2 Windows CE Control Panel........................................................................................................ 6-2

6.2.1 Open Control Panel.................................................................................................................... 6-2

6.2.2 Communication .......................................................................................................................... 6-5

6.2.3 Date/Time................................................................................................................................... 6-5

6.2.4 Input panel ................................................................................................................................. 6-6

6.2.5 Network ...................................................................................................................................... 6-6

6.2.6 OP .............................................................................................................................................. 6-7

6.2.7 Printer....................................................................................................................................... 6-10

6.2.8 Regional Settings..................................................................................................................... 6-13

6.2.9 Screen Saver ........................................................................................................................... 6-13

6.2.10 System ..................................................................................................................................... 6-15

6.2.11 UPS.......................................................................................................................................... 6-16

6.2.12 Volume & Sounds .................................................................................................................... 6-17

6.3 Network operation .................................................................................................................... 6-17

6.3.1 Basic principles ........................................................................................................................ 6-17

6.3.2 Configuring the HMI device for network operation................................................................... 6-18

6.3.3 Test network............................................................................................................................. 6-20

6.3.4 Configuring network access..................................................................................................... 6-21

7 Prepare and backup project.................................................................................................................... 7-1

7.1 Transfer project to the HMI device............................................................................................. 7-1

7.1.1 Commissioning for the first time................................................................................................. 7-1

7.1.2 Recommissioning....................................................................................................................... 7-3

7.2 Transfer...................................................................................................................................... 7-3

7.2.1 Start transfer manually............................................................................................................... 7-3

7.2.2 Start transfer automatically ........................................................................................................ 7-4

7.2.3 Transfer mode options ............................................................................................................... 7-5

7.2.4 Testing the project...................................................................................................................... 7-8

7.2.5 Uploading project ..................................................................................................................... 7-10

7.3 System settings........................................................................................................................ 7-12

7.3.1 Set language ............................................................................................................................ 7-12

7.3.2 Set operating mode.................................................................................................................. 7-13

7.4 Other transfer functions............................................................................................................ 7-14

7.4.1 Functions.................................................................................................................................. 7-14

7.4.2 Backup and Restore................................................................................................................. 7-15

7.4.3 Update operating system ......................................................................................................... 7-18

7.4.4 Transferring authorizations ...................................................................................................... 7-20

7.4.5 Transferring options ................................................................................................................. 7-22

8 Runtime functionalities of a project ......................................................................................................... 8-1

Table of contents

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 ix

8.1 Screen objects ........................................................................................................................... 8-1

8.2 Alarms ........................................................................................................................................ 8-2

8.3 Tags ........................................................................................................................................... 8-3

8.4 Logs ........................................................................................................................................... 8-3

8.5 Reports....................................................................................................................................... 8-5

8.6 System functions and scripts ..................................................................................................... 8-6

8.7 Safety ......................................................................................................................................... 8-7

8.8 Other operating functions........................................................................................................... 8-8

9 Operating a project ................................................................................................................................. 9-1

9.1 Basic principles of operation ...................................................................................................... 9-1

9.1.1 Basics for operation in Runtime ................................................................................................. 9-1

9.1.2 Operating the touch panel (TP).................................................................................................. 9-2

9.1.2.1 Operating touch objects ............................................................................................................. 9-2

9.1.2.2 Input of values............................................................................................................................ 9-4

9.1.2.3 Input of numeric values.............................................................................................................. 9-5

9.1.2.4 Input of alphanumeric values..................................................................................................... 9-5

9.1.2.5 Calling the operator note............................................................................................................ 9-6

9.1.3 Operating a keyboard device..................................................................................................... 9-7

9.1.3.1 Functions of the system keys..................................................................................................... 9-7

9.1.3.2 Functions of the key combinations............................................................................................. 9-9

9.1.3.3 Calling the operator note.......................................................................................................... 9-11

9.2 Controlling graphic objects....................................................................................................... 9-13

9.2.1 Button....................................................................................................................................... 9-13

9.2.1.1 Description ............................................................................................................................... 9-13

9.2.1.2 Touch control ........................................................................................................................... 9-13

9.2.1.3 Keyboard control...................................................................................................................... 9-13

9.2.1.4 Mouse and keyboard control.................................................................................................... 9-14

9.2.2 Switch....................................................................................................................................... 9-14

9.2.2.1 Description ............................................................................................................................... 9-14

9.2.2.2 Touch control ........................................................................................................................... 9-15

9.2.2.3 Keyboard control...................................................................................................................... 9-15

9.2.2.4 Mouse and keyboard control.................................................................................................... 9-15

9.2.3 I/O field..................................................................................................................................... 9-16

9.2.3.1 Description ............................................................................................................................... 9-16

9.2.3.2 Touch control ........................................................................................................................... 9-16

9.2.3.3 Keyboard control...................................................................................................................... 9-17

9.2.3.4 Operation with mouse and keyboard ....................................................................................... 9-17

9.2.4 Graphic I/O field ....................................................................................................................... 9-18

9.2.4.1 Description ............................................................................................................................... 9-18

9.2.4.2 Touch control ........................................................................................................................... 9-18

9.2.4.3 Keyboard control...................................................................................................................... 9-19

9.2.4.4 Mouse and keyboard control.................................................................................................... 9-19

9.2.5 Symbolic I/O field ..................................................................................................................... 9-20

9.2.5.1 Description ............................................................................................................................... 9-20

9.2.5.2 Touch control ........................................................................................................................... 9-20

9.2.5.3 Keyboard control...................................................................................................................... 9-21

9.2.5.4 Mouse and keyboard control.................................................................................................... 9-21

9.2.6 Alarm indicator ......................................................................................................................... 9-22

9.2.6.1 Description ............................................................................................................................... 9-22

9.2.6.2 Touch control ........................................................................................................................... 9-22

9.2.6.3 Mouse control........................................................................................................................... 9-23

9.2.7 Alarm view................................................................................................................................ 9-23

Table of contents

MP 370 (WinCC flexible)

x Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.7.1 Description ............................................................................................................................... 9-23

9.2.7.2 Touch control ........................................................................................................................... 9-24

9.2.7.3 Keyboard control ...................................................................................................................... 9-24

9.2.7.4 Mouse and keyboard control.................................................................................................... 9-25

9.2.8 Simple alarm view .................................................................................................................... 9-25

9.2.8.1 Description ............................................................................................................................... 9-25

9.2.8.2 Touch control ........................................................................................................................... 9-27

9.2.8.3 Keyboard control ...................................................................................................................... 9-27

9.2.8.4 Mouse and keyboard control.................................................................................................... 9-28

9.2.9 Recipe view.............................................................................................................................. 9-28

9.2.9.1 Description ............................................................................................................................... 9-28

9.2.9.2 Touch control ........................................................................................................................... 9-29

9.2.9.3 Keyboard control ...................................................................................................................... 9-30

9.2.9.4 Mouse and keyboard control.................................................................................................... 9-30

9.2.10 Simple recipe view ................................................................................................................... 9-31

9.2.10.1 Description ............................................................................................................................... 9-31

9.2.10.2 Touch control ........................................................................................................................... 9-32

9.2.10.3 Keyboard control ...................................................................................................................... 9-32

9.2.10.4 Mouse and keyboard control.................................................................................................... 9-33

9.2.11 Bar............................................................................................................................................ 9-34

9.2.12 Trend view................................................................................................................................ 9-35

9.2.12.1 Description ............................................................................................................................... 9-35

9.2.12.2 Touch control ........................................................................................................................... 9-36

9.2.12.3 Keyboard control ...................................................................................................................... 9-36

9.2.12.4 Mouse and keyboard control.................................................................................................... 9-37

9.2.13 Slider control ............................................................................................................................ 9-38

9.2.13.1 Description ............................................................................................................................... 9-38

9.2.13.2 Touch control ........................................................................................................................... 9-38

9.2.13.3 Keyboard control ...................................................................................................................... 9-39

9.2.13.4 Mouse and keyboard control.................................................................................................... 9-39

9.2.14 Gauge....................................................................................................................................... 9-40

9.2.15 Date / time field ........................................................................................................................ 9-41

9.2.15.1 Description ............................................................................................................................... 9-41

9.2.15.2 Touch control ........................................................................................................................... 9-41

9.2.15.3 Keyboard control ...................................................................................................................... 9-41

9.2.15.4 Mouse and keyboard control.................................................................................................... 9-42

9.2.16 Clock ........................................................................................................................................ 9-43

9.2.17 User view ................................................................................................................................. 9-44

9.2.17.1 Description ............................................................................................................................... 9-44

9.2.17.2 Touch control ........................................................................................................................... 9-45

9.2.17.3 Keyboard control ...................................................................................................................... 9-45

9.2.17.4 Mouse and keyboard control.................................................................................................... 9-45

9.2.18 Simple user view ...................................................................................................................... 9-46

9.2.18.1 Description ............................................................................................................................... 9-46

9.2.18.2 Touch control ........................................................................................................................... 9-46

9.2.18.3 Keyboard control ...................................................................................................................... 9-46

9.2.18.4 Mouse and keyboard control.................................................................................................... 9-47

9.2.19 Status force .............................................................................................................................. 9-48

9.2.19.1 Description ............................................................................................................................... 9-48

9.2.19.2 Touch control ........................................................................................................................... 9-49

9.2.19.3 Keyboard control ...................................................................................................................... 9-49

9.2.19.4 Mouse and keyboard control.................................................................................................... 9-50

9.2.20 Sm@rtClient view..................................................................................................................... 9-51

9.2.20.1 Description ............................................................................................................................... 9-51

9.2.20.2 Touch control ........................................................................................................................... 9-53

9.2.20.3 Keyboard control ...................................................................................................................... 9-53

9.2.20.4 Mouse and keyboard control.................................................................................................... 9-53

Table of contents

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 xi

9.2.21 Symbol library .......................................................................................................................... 9-54

9.2.21.1 Description ............................................................................................................................... 9-54

9.2.21.2 Touch control ........................................................................................................................... 9-55

9.2.21.3 Mouse control........................................................................................................................... 9-55

10 Operating recipes ................................................................................................................................. 10-1

10.1 Recipes .................................................................................................................................... 10-1

10.2 Structure of recipes.................................................................................................................. 10-3

10.3 Structure of recipe data records............................................................................................... 10-4

10.4 Recipe application.................................................................................................................... 10-5

10.4.1 Transfer of recipe data records................................................................................................ 10-5

10.4.2 Configuration of recipes ........................................................................................................... 10-6

10.4.3 Scenario: Entering recipe data records in Runtime ................................................................. 10-9

10.4.4 Scenario: Manual production sequence ................................................................................ 10-10

10.4.5 Scenario: Automatic production sequence ............................................................................ 10-11

10.5 Displaying recipes.................................................................................................................. 10-12

10.5.1 Viewing and editing recipes in Runtime................................................................................. 10-12

10.5.2 Behavior of the recipe view in Runtime ................................................................................. 10-14

10.6 Recipe data record administration ......................................................................................... 10-14

10.6.1 Recipe data record administration ......................................................................................... 10-14

10.6.2 Synchronizing a recipe data record ....................................................................................... 10-16

10.6.3 Read recipe data record from PLC ........................................................................................ 10-17

10.6.4 Transfer recipe record to PLC................................................................................................ 10-17

10.6.5 Exporting and importing recipe data records ......................................................................... 10-18

10.6.6 Reactions to modifications of the recipe structure................................................................. 10-19

10.7 Example ................................................................................................................................. 10-20

10.7.1 Example: Creating a recipe.................................................................................................... 10-20

10.7.2 Example: Configuring a recipe screen................................................................................... 10-21

11 Maintenance/Service ............................................................................................................................ 11-1

11.1 Clean screen/keyboard foil ...................................................................................................... 11-1

11.1.1 General information ................................................................................................................. 11-1

11.1.2 Notes on the touch panel ......................................................................................................... 11-1

11.2 Replacing the optional backup battery..................................................................................... 11-2

12 Technical Specifications ....................................................................................................................... 12-1

12.1 Dimension drawings................................................................................................................. 12-1

12.1.1 Dimensions MP 370 12" Touch ............................................................................................... 12-1

12.1.2 Dimensions MP 370 15" Touch ............................................................................................... 12-3

12.1.3 Dimensions MP 370 12" Key ................................................................................................... 12-4

12.2 Technical specifications ........................................................................................................... 12-5

12.3 EMC requirements ................................................................................................................... 12-7

12.4 Interface description................................................................................................................. 12-8

A Appendix.................................................................................................................................................A-1

A.1 Certificates and Directives ......................................................................................................... A-1

A.1.1 Approvals ...................................................................................................................................A-1

A.1.2 ESD guidelines ..........................................................................................................................A-2

A.2 System alarms ...........................................................................................................................A-4

B Abbreviations..........................................................................................................................................B-1

Table of contents

MP 370 (WinCC flexible)

xii Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

C Glossary .................................................................................................................................................C-1

Index

Tables

Table 1-1 Communication with SIMATIC PLCs ......................................................................................... 1-8

Table 1-2 Communication with PLCs from other manufacturers ............................................................... 1-9

Table 12-1 15-pin Cannon connector......................................................................................................... 12-8

Table 12-2 9-pin Sub-D socket (configuration via switch).......................................................................... 12-9

Table 12-3 9-pin Sub-D plug (pin).............................................................................................................. 12-9

Table 12-4 RJ45 plug connection............................................................................................................. 12-10

Table 12-5 USB standard plug ................................................................................................................. 12-10

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-1

Overview 1

1.1 Multi Panel MP 370

Multifunctional platform

The SIMATIC Multi Panels are included in the "Multifunctional Platform" product category.

This product category is positioned in the product hierarchy between the process-related,

optimized application components, such as operator panels and controllers, and industrial

PCs. This sector is completed by the introduction of the MP 370 15" Touch device variant

intended for high-end users.

The multifunctional platform is based on the innovative standard operating system, Microsoft

Windows CE. It combines the robustness and speed of the dedicated hardware solutions

with the flexibility of the PC world.

Multi Panels provide the following advantages:

• High degree of configuration efficiency

• Configuration simulation on the configuration computer - no PLC required

• Clear display and easy process operation using a Window-Based user interface

• Large selection of predefined screen objects for use during configuration

• Dynamic screen objects (e.g. moving objects),

• Uncomplicated and quick handling of recipes and data records in recipe screens and

recipe views

• Logging of alarms, process values and login/logout procedures

• Creation of vector graphics using the WinCC flexible configuration software without an

external graphics editor,

• Visual Basic Script for the realization of customized functions,

• ALARM_S alarm procedure in connection with the SIMATIC S7,

• Transfer:

– Automatic switchover to transfer mode

– Transfer via MPI, PROFIBUS/DP, USB and Ethernet

– Serial transfer

– Transfer via TeleService

• Standard connections to SIMATIC S5/DP, SIMATIC S7 and SIMATIC 505, as well as to

PLCs from other manufacturers

Overview

1.2 Area of use

MP 370 (WinCC flexible)

1-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Position in the SIMATIC HMI environment

The MP 370 extends the multifunctional platform product category for the upper performance

range. It meets the demands placed on performance, display possibilities and

price/performance ratio. In addition, it extends the communication potential of the office

world. Customer needs and requests were taken into account in respect to extending data

transfer functions, simplifying operation, and increasing acceptance when compared with

Windows CE units. The introduction of the new touch panel unit with a 15” display means

that this product category is now provided with a large screen with an increased visualization

area.

The MP 370 consistently implements the concept of multifunctionality. In addition to

supporting the traditional HMI applications (visualization with WinCC flexible), it also

supports other applications such as process diagnostics (SIMATIC ProAgent/MP), UPS,

Terminal Client (SIMATIC ThinClient/MP) for the touch screen units and Soft PLC (SIMATIC

WinAC-MP). In addition, the MP 370 can also be used within the scope of the OPP (Open

Platform Program).

The MP 370 is available as different device models with operation via touch panel or

membrane keyboard according to the respective visualization tasks.

1.2 Area of use

Overview

The HMI device allows graphic display of operating statuses, current process data and errors

of connected PLCs. The user can operate and observe the machine or system being

monitored easily using the HMI device.

Applicable areas of use include machine and apparatus construction sectors, printing and

packing industries, automobile and electrical industries and chemical and pharmaceutical

industries.

The high degree of protection (IP65 on the front side) and avoidance of moving storage

media, such as hard disks and floppy disks, ensure that the HMI device is suitable for use in

rough industrial environments and on site where a machine is located.

Possible installation locations for the HMI device:

• Switching cabinets/consoles

• 19" cabinets/racks (keyboard units)

Connection options for external peripherals (keyboard, mouse and printer) via a USB port,

for example, and the possible use of CF and PC cards support multifunctionality. Due to the

fact that the HMI device is equipped with high performance basic hardware and has a

minimum installation depth means that it fulfills all the requirements for operation in the

vicinity of the machine.

The HMI device can be used to:

• Operate and monitor the process using the menu system. Setpoint values or control

element settings can be modified by entering values or activating configured softkeys

• Display processes, machines and systems on full-graphic, dynamic screens

• Display and process alarms and tags through output fields, bar graphs or trend curves

• Use input to intervene directly in the running process

Overview

1.3 Configuring with WinCC flexible

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-3

1.3 Configuring with WinCC flexible

Introduction

In order to operate a machine or system using an HMI device, the user interface must be

configured for the HMI device. This procedure is referred to as the "configuration phase".

Create project data

Save project data

Test the configuration

Simulate configuration

Download project data

Connected to PLC

Configuration phase

PC/PU

PLC

MP 370

Process running phase

Figure 1-1 Configuration and process running phases

Principle

1. Configuring the functionality of the user interface. This includes the following:

– Graphics

– Text

– Customized functions

– Operating and indicator elements

For this purpose, use a configuration computer (PC or programming device) containing

the WinCC flexible configuration software.

2. Connect the configuration computer to the HMI device.

The following connection options are available:

– Serial

– MPI/PROFIBUS-DP network

– USB or Ethernet interface

– Standard modem path

3. Transfer the configuration to the HMI device.

4. Connect the HMI device to the PLC.

Overview

1.4 Features

MP 370 (WinCC flexible)

1-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Result

The HMI device communicates with the PLC and responds to the program progress in the

PLC ("process running phase") according to the information configured.

1.4 Features

Overview of the HMI device

Figure 1-2 MP 370 as keyboard unit and touch panel unit

Features MP 370 12"

Key

MP 370 12"

Touch

MP 370 15"

Touch

Processor Type 64 bit RISC CPU

Memory Capacity (max.) Free for user data:

12 MB flash memory (max. 7 MB for WinCC

flexible configurations)

Software Operating system Microsoft Windows CE

Standard HMI device

interfaces for connection

to PLC, PC/PU and

printer

1 x RS 232/TTY (active/passive)

1 x RS 232 (9-pin)

1 x RS 422/RS485

S7 connection MPI/PROFIBUS–DP

Interfaces

More interfaces for

network, external

keyboard and mouse

1 x Ethernet (10/100 Mbit)

1 x USB (12 Mbaud/Host)

Type TFT LCD TFT LCD with touch panel

(analog resistive)

Active screen diagonal 12,1" 15,1"

Color display

Resolution (pixels) 800 x 600 (Super VGA) 1024 x 768

(XGA)

Overview

1.5 Functional scope

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-5

Features MP 370 12"

Key

MP 370 12"

Touch

MP 370 15"

Touch

Possible colors 256

Back-lighting CCFL tubes

System keys with

dedicated functions

38 (3 with

LEDs)

Softkeys with

configurable functions

36 (with LEDs) -

for local assignment 36 -

Membrane keyboard

Softkey labeling System-

specific with

labeling strips

Acoustic

acknowledgement

In the case of touch

control

- x

External memory

extension for recipes,

logs and alarms etc.:

Special features

Slot for PC card

Slot for CF card

Further information

The creation of projects for HMI devices and functions for the configuration software is

described in detail in the "WinCC flexible" user manual and in the WinCC online help.

Information on connecting the HMI device to the PLC is provided in the "WinCC flexible

Communication" user manual.

The "Readme.chm" file on the WinCC flexible CD contains the most current information

which could not be included in the manuals and online help due to time constraints.

1.5 Functional scope

General information

The following table summarizes the range of functions provided by the HMI device. The

numeric values are maximum values which the HMI device is capable of managing. These

values are not cumulative. It is not possible to simultaneously configure 4000 alarms and

300 screens each with 400 tags per screen.

The defined values are also limited by the size of the configuration memory.

Function Keyboard unit Touch panel unit

Number 4000

Discrete alarms Yes

Analog alarms Yes

Alarms

Indicators Alarm line/Alarm window/alarm view

Overview

1.5 Functional scope

MP 370 (WinCC flexible)

1-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Function Keyboard unit Touch panel unit

Process values in alarm text 8

Length of the alarm text 80 characters (dependent on font)

Color-coding of different alarm states x

Warning alarms x

Error alarms

Type of display

Acknowledge individual alarms

Acknowledge several error alarms

simultaneously (group

acknowledgement)

First/last, selectable

16 acknowledgment groups

ALARM_S Display S7 alarms x

Alarm logging Output to printer x

Alarm buffer capacity 1024 alarm events, circular buffer

View alarms x

Delete x

Volatile alarm buffer

Print x

Time of occurrence Date/time Alarm acquisition

Alarm events Arrived, departed, acknowledged

Number 500

Text objects 30000 text elements

Fields per screen 400

Tags per screen 400

Screens

Screen objects • Button

• Switch

• I/O field

• Graphic I/O field

• Symbolic I/O field

• Alarm indicator

• Alarm view

• Alarm window

• Recipe view

• Bar

• Trend view

• Slider control

• Gauge

• Date / time field

• Clock

• User view

• Status force

• Sm@rtClient view

• Symbol library

Overview

1.5 Functional scope

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-7

Function Keyboard unit Touch panel unit

Operator prompting:

Help text

Animation

Unhide/hide objects

Pictograms for function keys

Tab order

LEDs in function keys

Fixed window x

Tags Number 2048

Limit value monitoring Input/output x

Conversion functions Input/output x

Lines/characters 7/35 (dependent on font)

For alarms x

For screens x

Help text

For screen objects

I/O field

Symbolic I/O field

Graphic I/O field

Button

Switch

Hidden button

Alarms x

Tags x

Log type Circular/sequential log

Number of logs 50

Number of tags for logging 50

Number of sequential logs 400

Entries per log 500000, limited by storage medium 2)

Logging

Memory location • PC card

• CF card

• Ethernet

Number 500

Graphics lists 500

Lists

Text lists 500

Hardcopy of the screen content, also in

color

Direct alarm logging x

Print functions

Freely configurable logs x

Number of user groups 10

No. of users 32

Safety

No. of authorizations Tag

Number 500 Recipes

Data records per recipe 2) 1000

Overview

1.6 Communication with PLCs

MP 370 (WinCC flexible)

1-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Function Keyboard unit Touch panel unit

Elements per recipe 1000

Recipe memory 128 KB (integr. Flash, expandable)

Number of languages 5 Online language change

Project languages (with system alarms) Chinese (simplified), Chinese (traditional),

Czechoslovakian, Danish, Dutch, English,

Finnish, French, German, Greek, Hungarian,

Italian, Japanese, Korean, Norwegian, Polish,

Portuguese, Russian, Spanish, Swedish,

Turkish

SIMATIC S5 x PU functions

(Status force) SIMATIC S7 x

Scheduler Trigger functions cyclically or once x

User-specific expansions of functionality x

Number of scripts 100

VBScript

Number of lines per script 500

Connections 3) Number 6

1) Maximum total number for PowerTags and internal tags

2) Storage media refers to PC cards, CF cards and network drives

3) With SIMATIC S7

1.6 Communication with PLCs

The following table list the PLCs which can be connected to the HMI device.

Table 1-1 Communication with SIMATIC PLCs

PLC Keyboard unit Touch panel unit

SIMATIC S5 AS511

SIMATIC S5 DP

SIMATIC S7–200 x

SIMATIC S7–300/400 x

SIMATIC 500/505 serial

SIMATIC 500/505 DP

SIMATIC HMI HTTP Protocol x

OPC 1) x

SIMATIC WinAC x

SIMOTION x

1) Data exchange only via XML (connection to OPC-XML server)

Overview

1.7 Options

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-9

Table 1-2 Communication with PLCs from other manufacturers

PLC Keyboard unit Touch panel unit

Allen Bradley DF1

Allen Bradley DH485

LG GLOFA-GM x

Modicon MODBUS x

Mitsubishi FX

Mitsubishi protocol 4

GE Fanuc SNP x

Omron Hostlink/Multilink x

1.7 Options

1.7.1 Hardware options

1.7.1.1 Backup battery

Function of the backup battery

The battery ensures that in the event of a power failure, the HMI device's internal hardware

clock continues to run. If no battery is available, the clock continues for approx. three days

as long as the HMI device was in operation for 6 to 8 hours, without interruption, beforehand.

The battery is not supplied with the HMI device. Please refer to the Siemens Catalog ST80

for the order number.

Procedure

1. Secure the battery to the back of the HMI device with two cable ties. The position is

indicated by an arrow for both touch panel and keyboard units in the following figures.

Figure 1-3 MP 370 12" Key

Overview

1.7 Options

MP 370 (WinCC flexible)

1-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Figure 1-4 MP 370 12" Touch

Figure 1-5 MP 370 15" Touch

2. Connect the plug on the battery cable to the two-pole connector strip on the underside of

the device. The plug is coded to prevent reversed poling.

See also

Interfaces (Page 4-4)

Replacing the optional backup battery (Page 11-2)

1.7.1.2 PC card / CF card

Purpose

Changeable PC cards and Compact-Flash cards can be inserted in the two slots, Slot A and

Slot B, at the rear of the HMI device. They are not supplied with the HMI device.

Changeable memory cards can be used, for example, to store important process data or

execute a backup/restore of the internal flash memory.

Slot A Slot B

Figure 1-6 Positions of the slots

Overview

1.7 Options

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 1-11

Cards supported

The HMI device supports the use of all standard cards which operate with a programming

voltage of 5 V (types I and II):

• Slot A (PC card):

– ATA Flash card

– SRAM card

– NE2000-compatible Ethernet card

• Slot B (Compact Flash Card):

– ATA Flash card

– NE2000-compatible Ethernet card

Remove memory card

Caution

Ensure that the HMI device does not access the memory card during the removal process.

Otherwise, the contents of the memory card will be fully destroyed.

1. Terminate access made by the HMI device to the memory card.

If the configuration planner has defined an operating element linked to the "CloseAllLogs"

system function, press the element. Otherwise, press the operating element linked to the

"Exit runtime" system function in the configuration. This stops the runtime software.

2. Wait unit the HMI device displays the loader.

Changeover to the loader may take several minutes depending on the size and number

of logs stored.

3. Remove the memory card.

Switch off the HMI device with memory card inserted

Caution

Always terminate the runtime software before switching off the voltage supply in order to

prevent loss of data.

1. Stop the runtime software.

Press the operating element linked to the "Exit runtime" system function in the

configuration.

2. Wait unit the HMI device displays the loader.

Changeover to the loader may take several minutes depending on the size and number

of logs stored.

Overview

1.7 Options

MP 370 (WinCC flexible)

1-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

3. Switch off the power supply.

If the power supply is interrupted during normal operation, the HMI device checks the

memory card after power is restored and repairs any defect sectors.

See also

HMI device loader (Page 6-1)

1.7.2 Software options

1.7.2.1 Internet Explorer

Overview

The Internet Explorer supplied with the HMI device has been specially adapted to the

Windows CE operating system and has a restricted functional scope (Pocket Internet

Explorer). Only small HTML pages, about 100 kb, can be displayed.

Installation of the Internet Explorer is completed using the ProSave service tool.

Files created in Internet Explorer (e.g. Favorites) are stored in the DRAM file system. The

DRAM file system is deleted when the unit is switched off. However, using the system

settings (OP Properties ? Persistent Storage ? Save Files), it is possible to backup the data

currently available in the DRAM file system to the Flash memory. When the device is started

up, the data saved is automatically restored.

If you remove the Internet Explorers, the files created from Internet Explorer must also be

deleted. To do this, delete the files in the DRAM file system using the standard Explorer.

Then backup the DRAM file system ("OP Properties ? Persistent Storage ? Save Files").

Note

The initial configuration can be restored simply by updating the operating system.

See also

Update operating system (Page 7-18)

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 2-1

Safety notes and general information 2

2.1 Safety notes

Work on the cabinet

Warning

Dangerous voltage

Opening the cabinet will expose high voltage parts. Contact with these parts could be fatal.

Switch off the power supply to the cabinet before opening it.

High frequency radiation

Notice

Undesirable operating conditions

High-frequency emissions, e.g. from cell phones, can cause undesirable operating

conditions.

2.2 General information

Industrial use

The HMI device is designed for industrial use. The following standards are met:

• Requirements for emitted interference in EN 61000-6-4: 2001

• Requirements for noise immunity in EN 61000-6-2: 2001

Safety notes and general information

2.2 General information

MP 370 (WinCC flexible)

2-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Residential use

If the HMI device is used in a residential area, you must take measures to achieve limit class

B in accordance with EN 55011 for radio interference emissions.

Suitable measures to achieve limit class B for suppression of radio interference include:

• Installation of the HMI device in a grounded control cabinet

• Use of filters in electrical supply lines

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 3-1

Plan deployment 3

3.1 Transport

Only unpack the HMI device at its location of use.

Notice

Ensure that no condensation develops on or in the HMI device after it has been transported

at low temperatures or it has been exposed to extreme temperature fluctuations.

llow the HMI device to warm up to room temperature before starting it up. Do not attempt to

warm the device using direct heat. If condensation has formed, the HMI device may only be

switched on when it has completely dried, normally after waiting approximately 4 hours.

Problem-free, reliable operation of the HMI device requires proper transport, storage,

positioning and assembly as well as careful operation and maintenance.

Failure to meet these requirements voids the rights to claims under the terms of warranty.

Notice

The HMI device was function-tested before shipping. If a malfunction occurs nevertheless,

please enclose a full description of the malfunction when returning the device.

3.2 Electromagnetic compatibility

Electromagnetic compatibility

The HMI device fulfills the requirements stipulated in the EMC law of the Federal Republic of

Germany as well as the EMC guidelines of the European Union.

Installation in grounded metal cabinets, e.g. 8 MC cabinet complying to Siemens catalog

NV21, ensures compliance to EN 61000-4-2.

Plan deployment

3.2 Electromagnetic compatibility

MP 370 (WinCC flexible)

3-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Installing HMI devices conform to EMC requirements

Conditions for error-free operation include a PLC design that conforms to EMC requirements

and the use of interference-proof cables. The "Guidelines for Interference-Free Construction

of PLCs" and the "PROFIBUS network Manual" are installation references for the HMI

device.

Caution

Only shielded cables are permitted for all signal connections.

Screw or lock all plug connections.

Do not install signal lines in the same cable ducts as power cables.

Siemens AG refuses to accept liability for malfunctions and damage arising from use of self-

made cables or cables from other manufacturers.

Conditions for use

The HMI device is intended for installation in weatherproof, permanent locations. The

conditions under which the device can be used exceed the requirements set out in DIN IEC

60721-3-3:

• Class 3M3 (mechanical requirements)

• Class 3K3 (climatic requirements)

Use with additional measures

Examples of applications where the use of the HMI device requires additional measures are:

• In locations with a high degree of ionizing radiation

• In locations with extreme operating conditions, e.g.:

– Corrosive vapors or gases

– Strong electric or magnetic fields

• In systems requiring special monitoring, e.g.:

– elevator systems

– In particularly hazardous locations

The HMI device may be installed in a cabinet as an additional measure.

See also

EMC requirements (Page 12-7)

Plan deployment

3.3 Installation locations and type of protection

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 3-3

3.3 Installation locations and type of protection

Installation location

The HMI device is designed for installation in the front panels of cabinets and consoles.

Keyboard units can also be installed in 19” cabinets and racks.

Cut an installation cut-out in a front panel. The thickness of the front panel must not exceed

6 mm. Additional holes for securing the HMI device are not necessary because a clamping

mechanism is available.

Degree of protection

Install the HMI device Install the HMI device to meet the minimum requirements for IP54

degree of protection. The IP65 degree of protection for the front panel can only be ensured

when the seal on the front plate of the HMI device is fitted correctly.

Notice

The NEMA 4, NEMA 12 and IP65 degrees of protection are only guaranteed when the

thickness of the installation support is at least 2.5 mm.

Caution

The system's ability to be waterproof and dustproof as per the section "Approvals" is only

guaranteed when the following are met:

• Material thickness of installation cut-out: 2,5 to 6 mm

• Deviation of the installation cut-out from the horizontal based on the overall dimensions of the HMI

device: ? 0.5 mm

• Permissible surface roughness in the area of the seal: max. 120 µm (Rz 120)

Ambient conditions

Caution

If the maximum permissible ambient temperature is exceeded, do not operate the HMI

device without external ventilation.

Otherwise, the HMI device may be damaged, nullifying the approvals listed in the

"Approvals" section as well as the warranty for the HMI device.

See also

Technical specifications (Page 12-5)

Approvals (Page A-1)

Plan deployment

3.4 Producing the installation cut-out

MP 370 (WinCC flexible)

3-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

3.4 Producing the installation cut-out

Select position for the installation cut-out

Caution

To prevent the HMI device from overheating during operation:

• The maximum angle of inclination from vertical installation may not be exceeded (see

"Specifications" chapter).

• Do not expose the operating unit to direct sunlight.

• Ensure that the ventilation slits in the housing are not obstructed.

Installation cut-out

Notice

The following air flow requirements must be maintained following installation:

• 100 mm above the HMI device

• 50 mm below the HMI device

• 15 mm at the sides of the HMI device

• 50 mm at the bottom of the HMI device

When using plug-in boards, ensure sufficient space is provided to insert or remove them.

MP 370 12" Touch

For installation in the front panel, the touch panel requires an installation cut-out (WxH) of

310 +1 mm x 248 +1 mm. The thickness of the front panel must not exceed 6 mm.

MP 370 15" Touch

For installation in the front panel, the touch panel requires an installation cut-out (WxH) of

368 +1 mm x 290 +1 mm. The thickness of the front panel must not exceed 6 mm.

MP 370 12" Key

For installation in the front panel, the keyboard unit requires an installation cut-out (WxH) of

450 +1 mm x 290 +1 mm. The thickness of the front panel must not exceed 6 mm.

See also

Technical specifications (Page 12-5)

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-1

Installation and connection 4

4.1 Check shipment

Check the packing contents for visible signs of transport damage and for completeness.

Notice

Do not install parts damaged during shipment. In the case of damaged parts, contact your

Siemens representative.

Keep the documentation supplied. It belongs to the HMI device and may be required for

future commissioning.

4.2 Installation of the HMI device

Prior to installation

If you want to change the labels on the softkeys, change the labeling strips before installing

the HMI device.

Installation in 19” cabinets/racks

Refer to the information provided by the respective cabinet or rack manufacturer to install the

device in a 19” cabinet/rack.

Installation dimensions of standard 19” cabinets:

• Width: 19" (482.6 mm)

• Height: 7 HE (310 mm)

Secure the HMI device: to the rails using four screws

See also

Labeling the softkeys (Page 5-6)

Installation locations and type of protection (Page 3-3)

Dimensions MP 370 12" Key (Page 12-4)

Installation and connection

4.2 Installation of the HMI device

MP 370 (WinCC flexible)

4-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4.2.1 Installation of the touch panel unit

Installation in front panels

1. Working from the front, insert the HMI device in the installation cut-out.

Note

Take the necessary precautions to ensure the HMI device cannot drop out of the front

panel before it has been secured.

2. When installing an MP 370 with a 12" display and touch control, hang the hooks of the

enclosed eight screw clamps into the recesses in the housing of the HMI device.

The recesses are marked by arrows in the figure.

MP 370 12”

Touch

Figure 4-1 Screw clamps on the MP 370 12" Touch

3. When installing an MP 370 with a 12" display and key control or an MP 370 with a 15"

display and touch control, hang the hooks of the enclosed ten screw clamps into the

recesses in the housing of the HMI device.

The recesses are marked by arrows in the figure.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-3

MP 370 15” Touch

MP 370 12" Key

Figure 4-2 Screw clamps on the MP 370 12" Key and MP 370 15" Touch

4. Secure the HMI device to the front panel from the back using an Allen wrench.

Caution

Make sure the seal is seated correctly against the front panel.

Over tightening the screws will damage the HMI device.

See also

Installation locations and type of protection (Page 3-3)

Dimensions MP 370 12" Touch (Page 12-1)

Dimensions MP 370 15" Touch (Page 12-3)

4.3 Connecting the HMI device

4.3.1 Conditions

Requirements

The following condition must be fulfilled before the HMI device is connected electrically:

• The HMI device must be installed according to the information provided in these

operating instructions.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Electrical connections

Connect the HMI device in the following sequence:

1. Potential equalization line

2. PLC

3. Configuration computer as necessary

4. Peripheral equipment as necessary

5. Power supply

Notice

Connection sequence

Make the HMI device connections in the order they are described. Failure to do so may

result in damage to the HMI device.

When disconnecting, it is essential that you follow the sequence in reverse order.

4.3.2 Interfaces

Interfaces

The following figure illustrates the arrangement of the ports on the underside of the HMI

device.

Figure 4-3 Arrangement of the ports

No. Name Application

1 Ground connection For connection to rack ground

2 Power supply Connection to power supply +24 V DC)

3 Interface IF1A RS232/TTY (active/passive) for controller

4 Interface IF2 RS232 for PC, PG, printer

5 Interface IF1B RS422/RS485 (floating) for controller

6 Switch To configure interface IF1B

7 Battery connection Connection for optional backup battery

8 USB interface Connection for external keyboard, mouse, etc.

9 Slot B For CF card

10 Ethernet interface Connection of an RJ45 Ethernet line

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-5

11 Slot A For PC card

Notice

Connecting a USB distributor (USB hub) to the HMI device's USB interface can cause a

restriction in the functionality of the connected USB devices and the HMI device.

Therefore, the simultaneous or alternating operation of USB devices connected via a USB

hub on the HMI device's USB interface is not approved.

This applies to USB hubs both with and without an internal power supply.

Notice

The connection and operation of USB memory media (e.g. USB stick) on the HMI device's

USB interface has not been approved.

Communication options

The following table lists the peripherals with which the HMI device can communicate.

Device Connection Interface

SIMATIC S5 AS511 (TTY)

PROFIBUS DP

IF1A

IF1B

SIMATIC S7 MPI

PROFIBUS DP

Industrial Ethernet

IF1B

Ethernet

SIMATIC 505 RS 232

RS 422/RS485

IF1A

IF1B

Further support RS 232/TTY

RS 422/RS485

IF1A

IF1B

Configuration computer RS 232 IF2

Printer

Local printer

Network printer

UBS printer

RS 232

Network

USB

IF2

Ethernet

USB

External keyboard/mouse USB

See also

Interface description (Page 12-8)

Connecting the power supply (Page 4-15)

Backup battery (Page 1-9)

Connecting the PLC (Page 4-11)

Technical specifications (Page 12-5)

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4.3.3 Connecting the potential equalization

Ground connection

Connect the grounding connection of the HMI device to the rack ground. Use the grounding

screw provided and a conducting cable with a diameter of at least 4 mm2.

Potential difference

Potential differences can occur between separate system parts which lead to high equalizing

currents. An example would be when line shields are applied on both sides and grounding

occurs on different system parts.

The cause of potential differences can be different supply connections.

General requirements for equipotential bonding

Potential differences must be reduced by laying sufficient equipotential bonding cables to

ensure problem-free operation of the electronic components concerned. Therefore, the

following must be observed when setting up equipotential bonding:

• The effectiveness of the equipotential bonding increases as the the impedance of the

equipotential bonding cables decreases (i.e., or as the cross section of the equipotential

bonding cable increases).

• If two system parts are connected to each other via shielded data lines with shielding

connected to the grounding/protective conductor on both sides, the impedance of the

additionally laid equipotential bonding cables must not exceed 10% of the shield

impedance.

• The cross-section of an equipotential bonding cable must be selected to accommodate

the maximum equalizing current flow. In practice, equipotential bonding cables between

control cabinets with a minimum cross-section of 16 mm2 have proven sufficient.

• Use equipotential bonding cables made of copper or galvanized steel. Connect the

equipotential bonding cables properly to the grounding/protective conductor with the

greatest possible surface area and protect them from corrosion.

• Clamp the shielding of the data line on the HMI device flush and as close as possible to

the potential equalization rail using cable clips.

• Lay the equipotential bonding cables and data lines parallel to one another with a

minimum gap (see figure below, Item 6).

Notice

Equipotential bonding cable

Cable shields are not suitable for equipotential bonding. Use only the intended potential

cable prescribed. For example, potential cables must have a minimum cross-section of

16 mm². When setting up MPI and PROFIBUS DP networks, make sure to use cables

with a sufficient cross&section; otherwise, the interface modules may be damaged or even

destroyed.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-7

Connection configuration

≥16

Data cable, shielded

Equipotential bonding

Figure 4-4 Setting up potential equalization in the HMI device

1 Grounding connection on the HMI device

2 Switching cabinet

3 Voltage bus

4 Cable clip

5 Grounding connection

6 Parallel laying of equipotential bonding cable and data line

4.3.4 Connecting peripheral equipment

4.3.4.1 Connect printer

Connection configuration

The figure below illustrates how to connect a printer to the HMI device. The HMI device

supports the following printer standards:

• compatible with ESC/P, 9-pin ESC/P or ESC/P2 (EPSON)

e.g., EPSON LQ 300+

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

• compatible with PCL3 (Hewlett Packard)

e.g., Brother HL 1450

USB printers can still be used for PCL and Epson9 modes.

IF2

Local printer (serial)

ESC/P, 9-pin ESC/P,

ESC/P2, PCL

RS 232 (cable is printer-specific)

Network printer

ESC/P, 9-pin ESC/P,

ESC/P2, PCL

Ethernet

USB

UBS printer

ESC/P, 9-pin ESC/P,

ESC/P2, PCL

Operating unit

Figure 4-5 Printer connection configuration

Notice

Connecting a USB distributor (USB hub) to the HMI device's USB interface can cause a

restriction in the functionality of the connected USB devices and the HMI device.

Therefore, the simultaneous or alternating operation of USB devices connected via a USB

hub on the HMI device's USB interface is not approved.

This applies to USB hubs both with and without an internal power supply.

Notice

Only use a cable with braided metal screening grounded at each end for connecting the HMI

device and printer.

Deactivate the "Printer" option in the "Serial Transfer Remote Control" setting in the

Windows CE Control Panel if a serial printer is connected to the HMI device via the IF2

interface.

Some printers may require the ASCII character set used in the project to also be defined on

the printer.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-9

If a serial printer is connected, the following printer settings are required:

• RS 232, whereby only the RxD, TxD and GND signals are required,

• 8 data bits

• 1 stop bit

• No parity

• Baud rate between 9600 and 57600, printer-dependent

• XON / XOFF protocol

The Siemens Catalog ST 80 contains the printers approved by Siemens AG. A current list of

approved printers is available on the Internet.

Note

Printer documentation

Refer to the information provide by the printer manufacturer when connecting the printer.

4.3.4.2 Connect external keyboard and mouse

Connection configuration

The figure below illustrates how to connect a keyboard or mouse to the HMI device's USB

interface. A keyboard or mouse can be connected and disconnected during normal

operation.

USB

USB standard keyboar

USB standard mouse

Operating unit

Figure 4-6 Connection configuration for external keyboard and mouse

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Notice

Connecting a USB distributor (USB hub) to the HMI device's USB interface can cause a

restriction in the functionality of the connected USB devices and the HMI device.

Therefore, the simultaneous or alternating operation of USB devices connected via a USB

hub on the HMI device's USB interface is not approved.

This applies to USB hubs both with and without an internal power supply.

Notice

Use a standard mouse and keyboard with a "USA/International" keyboard layout.

Commercially available USB devices do not normally meet the higher industrial demands

relating to interference resistance and can have negative effects on the HMI device.

The power consumption must not exceed 500 mA with the USB units connected.

See also

Operation with external keyboard/mouse (Page 5-9)

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-11

4.3.5 Connecting the PLC

Connection configuration

The figure below illustrates the basic connection possibilities between the HMI device and

PLC. Standard cables are available for the connections shown (refer to the ST80 catalog).

TTY active

PU interface

SI 2

RS 232

(9/25-pin)

RS 422

(9-pin)

SIMATIC S5

TTY active

RS 232

PLCs of other

manufacturers

RS 422

RS 422/RS485

CPU

SIMATIC 505

SIMATIC S7

RS 232/TTY

IF1A

IF1B

RS 485

Operating

unit

PROFIBUS DP

Figure 4-7 Connection configuration for PLCs

• SIMATIC S7

Use only the approved cables for connection to a SIMATIC S7.

• IF1A / IF1B

To enable operation using the serial interface, connect either the IF1A (RS 232/TTY) or

IF1B (RS 422/485), but not both. The 1F1B interface can be configured using a switch.

• PROFIBUS DP

Any PROFIBUS-DP bus terminal can be used.

Configure interface IF1B

The IF1B interface can be configured via the switches on the back of the HMI device. This

switches over the RS-422 received data and the RTS signal for RS485. By default, the

switch is set for the SIMATIC S7 PLC.

The following table shows the permissible switch settings.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Communication Switch settings

PLC

MPI/PPI

Standard cable

Operati ng

unit

1234

No RTS on connector

This is the switch setting on

delivery.

PLC

RS 422/RS 485

Operating

unit

1234

RTS on Pin 4 (default)

1234

RTS on Pin 9 (as PU)

PLC

PROFIBUS-DP/MPI

Operating

unit

1234

No RTS on connector

Compressing the internal program memory with SIMATIC S5

Warning

In the case of the SIMATIC S5, compressing the PLC's internal program memory

("Compress" PU function, integrated FB COMPR) is not permitted if an HMI device is

connected. When memory is compressed, the absolute addresses of the blocks in the

program memory change. Since the HMI device only reads the address list during startup, it

does not recognize the address change and accesses the wrong memory areas.

If you cannot avoid compressing memory during operation, turn off the HMI device before

running the compress function.

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-13

4.3.6 Connecting the configuration computer

Connection configuration

The figure below illustrates how to connect a configuration computer (PG or PC) to the HMI

device for transferring project data.

Standard cables are available for the connections shown (refer to the Siemens catalog

ST80).

COM

IF2

PC/PU

RS 232

IF1 B

MPI/PROFIBUS DP

RS 485

PC/PU

RJ45

PC/PU

Ethernet

USB USB

PC/PU

Operating unit

Figure 4-8 Connection configuration for configuration computer

Notice

Use a master-master cable for the USB connection between the HMI device and the

configuration computer. Do not use the driver supplied with the cable for the transfer. Only

install the USB driver supplied with WinCC flexible on the configuration computer. This drive

is on the WinCC flexible CD under "\Support\DeviceDriver\USB".

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

4-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4.3.7 Connecting an uninterruptible power supply (UPS)

Connecting a UPS

The following options are available to connect a UPS:

• UPS with serial interface

A UPS with serial interface is connected directly to the HMI device.

A serial connection is used with a "SITOP DC-USV Module A". The driver for detecting

and configuring the UPS is contained on the WinCC flexible CD and must be installed on

the HMI device using ProSave.

• UPS without serial interface

A UPS without serial interface is connected to the PLC.

The UPS signals the power failure to the connected PLC via a digital signal. The PLC

program must then signal the HMI device that runtime must be terminated. To do this, the

PLC changes a tag to which the "Exit runtime" function is configured in WinCC flexible.

Note

In order to use an uninterruptible power supply with serial interface on the HMI device,

the "Uninterruptible Power Supply (UPS)" option must be loaded on the HMI device.

Connection configuration

The figure below illustrates how to connect an uninterruptible power supply UPS with serial

interface to the HMI device.

IF2

UPS

RS 232

24 V

Operating unit

Figure 4-9 Connection configuration for an uninterruptible power supply

See also

UPS (Page 6-16)

Installation and connection

4.3 Connecting the HMI device

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 4-15

4.3.8 Connecting the power supply

Connecting the plug-in terminal rail

The power supply for the HMI device is connected at the 2-pin plug connector on the

underside of the unit. Use the 2-pin terminal block supplied for this purpose. The plug-in

terminal block is designed for cables with a cross-section not larger than 2.5 mm2.

The figure below illustrates the assignment of the plug-in terminal block.

GND

+ 24 V D

Ensure that the lines are connected properly to the correct terminals. Also note the labeling

for the contact pins on the back of the HMI device.

The HMI device is equipped with reverse battery protection.

Notice

Damage

The force of the screwdriver on the screws may cause the socket for the terminal block in

the HMI device to be levered up from the printed circuit board.

Therefore, only connect the wires when the terminal block has been unplugged.

Connecting the power supply

Please refer to Technical Data for information on the power supply requirements.

Caution

Ensure safe electrical insulation of the power supply. Use only power supply units complying

with IEC 364&-4&-41 or HD 384.04.41 (VDE 0100, Part 410).

Only use power supply units which comply to SELV (Safety Extra Low Voltage) and PELV

(Protective Extra Low Voltage) standards.

The supply voltage must be within the specified range. Otherwise, HMI device failures can

occur.

If the power supply for the HMI device is not grounded, the communication interface could

be destroyed by the potential difference between the HMI device and CPU.

Therefore, connect the 24 V output of the power supply to the potential equalization.

Installation and connection

4.4 Switch on and test the HMI device

MP 370 (WinCC flexible)

4-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

See also

Technical specifications (Page 12-5)

4.4 Switch on and test the HMI device

Start up

Proceed as follows:

1. Disconnect all connections to external units and remove any cards from the slots.

2. Connect the HMI device to the power supply.

3. Switch on the power supply.

If the HMI device does not start, the connections are probably reversed. In this case,

switch of the power supply, reverse the connections and switch the power supply on

again.

4. When the HMI device has started, connect the configuration computer or other peripheral

equipment to it.

Function test

Initiate a function test following commissioning. The HMI device is functional when one of the

following conditions occurs:

• The "Transfer" dialog is displayed

• The loader is displayed

• A project is started

Switch off HMI device

Switch off the HMI device in the following ways:

• Switch off the power supply

• Unplug the terminal strip from the HMI device

Note

If a project is already running on the HMI device, runtime must be terminated before

switching the HMI device off.

Use the operating element provided by the project engineer.

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 5-1

Operating elements and indicators 5

5.1 Front view MP 370 Touch

Operating the touch screen

Notice

Damaging the touch screen

Operating the touch screen with hard, sharp or pointed items or in a heavy-handed way can

lead to a considerable reduction in its service life and even to a complete failure.

Only press the HMI device's touch screen with your fingers or a touch screen pen.

MP 370 12" Touch

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

5-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 15" Touch

5.2 Front view MP 370 Key

5.2.1 Key pads

Operating the keyboard

Notice

Damaging the keyboard

Operating the keyboard with hard, sharp or pointed items or in a heavy-handed way can lead

to a considerable reduction in its service life and even to a complete failure.

Only use your fingers to operate the HMI device keyboard.

Key pads

The HMI device's keyboard is comprised of two functional keypads. Refer to the figure

below.

• Softkeys

– Keys <S1> to <S16>

– Keys <F1> to <F20>

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 5-3

• System keys:

– Alphanumeric keys

– Cursor keys

– Control keys

Figure 5-1 Arrangement of the keypads

1 Function keys

2 System keys

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

5-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

5.2.2 Function keys

Function keys with global function assignment

A softkey with global function assignment always triggers the same action on the HMI device

or in the PLC. The action is independent of the screen currently selected. These actions

could include:

• Activate screen

• Display current error alarms

• Start screen printout (hardcopy)

All softkeys can be configured with global assignments.

Note

Unintentional actions can be triggered by a multiple key operation.

No more than two function keys can be activated simultaneously.

Function keys with local function assignment

A softkey with local function assignment can trigger different actions on the HMI device or in

the PLC. The actions are dependent on the currently active screen (local significance of

current screen). A configuration engineer can configure an icon for each softkey. The icon is

then positioned on the screen.

All function keys can be assigned locally significant functions during configuration.

Icons cannot be configured for the keys <F11> to <F20>.

Caution

If you press a function key after a screen change, the associated function in the new screen

may be initiated before the new screen is displayed.

LED control

The light-emitting diodes (LED) in the function keys can be controlled from the PLC. A

luminous or flashing LED can indicate to the operator which key to press according to

specific situations.

The configuration engineer must configure LED tags for the softkeys to control the LEDs.

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 5-5

5.2.3 System keys

Control keys

The following control keys serve higher editing and control functions:

A-Z INS

DEL TAB

HELP

ESC

ACK

SHIFT FNCTRL ALT ENTER

Figure 5-2 Control keys

The system keys <ACK>, <ESC>, <HELP> and <ENTER> can also be assigned functions

by the project engineer.

1 Toggling (numbers / letters)

2 Delete character to the left of the current cursor position

3 Delete character at the current cursor position.

4 Tabulator

5 Viewing the operator note

6 Cancel

7 Acknowledge

8 Enter

9 General control function (for key combinations)

10 General control function (for key combinations)

11 Shift (special character)

12 Shift (upper/lower case)

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

5-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Alphanumeric keys

Use the following alphanumeric keys to enter digits, letters and special characters:

´.

"°

{}()

§3

[]

Figure 5-3 Alphanumeric keys

Cursor keys

The cursor keys are used to move the text cursor and to navigate in screens and screen

objects. The functions of the keys corresponds to the cursor keys on a standard PC

keyboard.

HOME

END

Figure 5-4 Cursor keys

The <HOME> and <END> keys can also be assigned functions by the project engineer.

5.2.4 Labeling the softkeys

Labeling

In the factory state, the softkeys on the keyboard unit are labeled as follows:

• F1 to F20 and

• S1 to S16.

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 5-7

A total of four labeling strips for the softkeys are inserted in the HMI device from the back.

Use these strips to label the HMI device specifically for the system.

Changing labeling strips

Warning

After opening the switching cabinet, certain system parts become accessible which may be

conducting dangerously high voltage.

1. Set the unit down with the front panel at the bottom.

2. Remove the existing labeling strips.

3. Insert the new labeling strips in the slots of the front panel with the inscription facing

down. The individual positions are indicated in the figure by means of arrows.

Caution

Wait for the ink to dry before inserting strips. A keyboard foil which is dirty on the inside

cannot be cleaned and can only be replaced at the manufacturer’s factory.

Figure 5-5 Placing the labeling strips on the MP 370 keys

1 Labeling strips for ten keys

2 Labeling strips for two keys

Operating elements and indicators

5.2 Front view MP 370 Key

MP 370 (WinCC flexible)

5-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Create labeling strips

Only use transparent foil to create your own labeling strips so that the LEDs in the softkeys

remain visible. Label the foil either with a printer or a waterproof felt-tip pen. Cut the strips

according to the specifications.

9.4

20.65

245

6.05

5.65

Figure 5-6 Labeling strip dimensions

Printing the labeling strips

The templates for the labeling strips are in the "Slide370.doc" file on the "WinCC flexible"

installation CD in the "\Support\Documents" folder. The file can be edited with MS Word for

example.

Pay attention to the information provided in the file.

Operating elements and indicators

5.3 Operation with external keyboard/mouse

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 5-9

5.3 Operation with external keyboard/mouse

Connection

An external keyboard or mouse can be connected to the USB interface on the HMI device.

Connection and disconnection are possible during normal operation of the HMI device (”hot

plug in/out”).

Operation of the HMI device via an external keyboard/mouse is particularly recommended

during the commissioning and test phases.

Notice

USB mouse:

• Use a standard mouse.

USB keyboard:

• Use a standard keyboard with a USA/International keyboard layout.

• Operation of the configured function keys is not possible via the external keyboard.

Commercially available USB devices do not normally meet the higher industrial demands

relating to interference resistance and can have negative effects on the HMI device.

Operation

Operation of the HMI device via a mouse is only slightly different from operation using the

touch screen. After connecting a mouse, the mouse pointer appears on the screen.

When the mouse pointer is positioned on an operable button, the mouse pointer symbol

changes .

Caution

When using a keyboard unit, do not operate the integrated membrane keyboard and

external USB keyboard simultaneously. You may trigger an unintended action.

See also

Connect external keyboard and mouse (Page 4-9)

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-1

Operating system and configuration 6

6.1 HMI device loader

Loader

The following figure illustrates the loader which appears briefly during the startup phase of

the HMI device.

Figure 6-1 HMI device loader

The loader also appears when runtime has ended.

The loader buttons have the following functions:

• Press the "Transfer" button to switch the HMI device to transfer mode.

• Press the "Start" button to start runtime with a project loaded on the HMI device.

• Press the "Control Panel" button to access the Windows CE Control Panel in which

various settings can be defined. The options for the transfer mode can be set here, for

example.

• Press the "Taskbar" button to display the Windows toolbar when the Windows CE Start

menu is open.

Protect loader with password

It is possible to protect the Loader from unauthorized access by assigning a password.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

If the password is not entered, only the "Transfer" and "Start" buttons are available. This

prevents incorrect operation and increases system or machine security since no changes

can be made to the settings.

Notice

If the password for the loader has been forgotten, it is only possible to access the Control

Panel again after updating the operating system.

All the data on the HMI device are overwritten when to operating system is updated.

See also

Open Control Panel (Page 6-2)

6.2 Windows CE Control Panel

6.2.1 Open Control Panel

Windows CE Control Panel

The Windows CE Control Panel can be used to modify the following system settings:

• Date/time

• Network

• Device properties, e.g. brightness and calibration of touch screens

• Regional settings

• Screensaver

• Screen keyboard

• Volume (touch acknowledgement)

• Printer

• Backup/Recovery

• Transfer

• UPS (optional)

Open Control Panel

The following options are available to open the Control Panel:

• During the startup phase:

Press the "Control Panel" button in the loader to open the Windows CE Control Panel. It

may be necessary to enter a password.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-3

• During normal operation:

– Provided one is configured, activate the operating element that is linked to the "Open

Control Panel" system function.

– The Control Panel can also be opened from the Windows CE Start menu by selecting

"Settings ▶ Control Panel".

Keyboard unit:

The Windows CE Start menu can be opened by pressing the key combination CTRL +

ESC .

Touch panel unit:

The Windows CE Start menu can be opened by pressing the button twice

(locking key) on the alphanumeric screen keyboard.

Result

The Control Panel is opened.

Figure 6-2 Windows CE Control Panel

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Change settings

Caution

End Runtime before making changes to system settings; otherwise the changes will not take

effect, e.g. for a transfer operation.

Proceed as follows to change settings using the Windows CE Control Panel:

1. Stop the runtime software before modifying any system settings. Use the relevant

operating element provided in the project.

2. Open the Control Panel as described above.

3. Change the system settings in the Control Panel.

4. Close the Control Panel:

Touch panel unit:

Press the button.

Keyboard unit:

Press the ALT key and use the cursor keys to select the menu command "File ▶ Close".

Confirm the selection by pressing the ENTER key.

5. Start runtime via the loader.

Note

Closing Control Panel dialogs using keyboard devices

Proceed as follows if dialogs, which are open on the HMI device, cannot be closed:

1. Open another dialog in the Control Panel.

2. Press the key combination ALT + TAB to access another open dialog.

3. Close the dialog by pressing ESC or ENTER .

4. Repeat steps 2 and 3, as necessary until all the dialogs are closed.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-5

6.2.2 Communication

"Communication" option

This function is used to change the name used by the HMI device on the network.

See also

Open Control Panel (Page 6-2)

Configuring the HMI device for network operation (Page 6-18)

6.2.3 Date/Time

"Date/Time" option

This is used to set the date, time and time zone for the HMI device.

Synchronizing date/time with the PLC

The date and time of the HMI device can be synchronized with the PLC, if this has been

configured in the project and the PLC program. The two PLC jobs 14 ("Set time") and 15

("Set date") are provided for this.

PLC jobs 40 and 41 can be used to transfer the date and time from the HMI device to the

PLC.

Notice

Synchronize the date and time when time-controlled responses should be triggered in the

PLC by the HMI device.

The HMI device can only buffer the date and time for a few days if no power is supplied. If

the HMI device is not to be used for a number of days, it is recommended to synchronize the

date and time via the PLC.

Further information on this is available in the "WinCC flexible Communication" user manual.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

See also

Open Control Panel (Page 6-2)

6.2.4 Input panel

"InputPanel" option

This function defines the position and size of the screen keyboard when it appears on the

HMI device.

Procedure

1. Select the "Input Panel" option.

2. Move the screen keyboard to the relevant position.

3. To change the size, press the "Start Resize" button.

4. Store the new settings by pressing the "Save" button.

5. Close the option by pressing the button or the ESC key.

Note

In order to correctly save the size and position of the on-screen keyboard in a fail-safe

way, the alphanumeric representation must be selected prior to the Save operation.

See also

Open Control Panel (Page 6-2)

6.2.5 Network

"Network" option

Network properties are configured here.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-7

See also

Configuring the HMI device for network operation (Page 6-18)

Open Control Panel (Page 6-2)

6.2.6 OP

"OP" option

The following setting options are provided by the "OP" option in the Control Panel:

• Set brightness

• Calibrate the touch screen (for touch panels)

• Display device data

• Backup non-resistant data

Set brightness

1. Open the "Display" tab in the "OP Properties" dialog.

Figure 6-3 "OP Properties" dialog, "Display" tab

2. Change the brightness setting of the screen using the "UP" and "DOWN" buttons in the

"Brightness" group.

3. In the case of the touch panel, close the dialog using the "OK" button. In the case of the

keyboard unit, move the focus to the tab heading by pressing <ENTER>.

In the case of keyboard devices, the brightness can be changed outside the Windows CE

Control Panel with the following key combinations:

A-Z + Increases the brightness.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

A-Z + Reduces the brightness.

Note

Wait at least 10 sec. after changing the setting before switching the HMI device off.

Otherwise, the changes will not be saved.

Calibrate touch screen

Purpose

Depending on the installation position and viewing angle, it is possible that a more or less

strong parallax may occur when operating the touch panel screen. In order to prevent

resulting operating errors, the screen can be calibrated during the start-up phase and normal

operation.

Procedure

1. Open the "Touch" tab in the "OP Properties" dialog.

Figure 6-4 "OP Properties" dialog, "Touch" tab

2. Press the "Recalibrate" button to start the calibration process.

Five calibration crosses appear in succession on the screen. Follow the instructions

provided on the screen and touch the respective calibration cross.

3. Apply calibration:

Touch any point on the screen after the calibration process for the new calibration data to

take effect.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-9

4. Reject calibration:

Wait 30 seconds (until the counter reaches zero) before rejecting the new calibration

data.

If calibration is not performed correctly, the new values are not accepted.

5. Press the "OK" button to close the dialog.

Configured function

If the "Calibrate Touch Screen" function has been linked to an operating element in your

project, the touch screen can be calibrated during operation. The triggering operator control

object can be configured in such a way that a password is required to calibrate the touch

screen.

The calibration process is identical with steps 2, 3 and 4 described for the start-up phase.

Persistent storage of registrations

1. Open the "Persistent Storage" tab in the "OP Properties" dialog.

Figure 6-5 "OP Properties" dialog, "Persistent Storage" tab

2. Press the Save Registry button to start the storage process.

The current registration settings are stored in the Flash memory.

3. Press the Save Files button to start copying the files in the RAM file system to the Flash

memory.

Following a restart, these saved files will be copied back to the file system.

4. In the case of the touch panel, close the dialog using the "OK" button. In the case of the

keyboard unit, move the focus to the tab heading by pressing <ENTER>.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Display device data

1. Open the "Device" tab in the "OP Properties" dialog.

Various device data is displayed.

Figure 6-6 "OP Properties" dialog, "Device" tab

2. Close the dialog using the "OK" button in the case of touch panels. Press the <ENTER>

button in the case of keyboard units.

See also

Open Control Panel (Page 6-2)

6.2.7 Printer

"Printer" option

A printer can be selected and set up using the "Printer" option. Some settings are only

relevant for printing a hardcopy of the screen contents and have no influence on the alarm

logging, e.g. color or quality of graphics printing.

Adjustable options

The available settings depend on the selected printer.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-11

Printer

Select the printer from the printer list on the connected HMI device.

Port

Select the port and baud rate used by the HMI device to transfer data to the printer, e.g. IF2:

9600.

Net Path

If a network has been configured, enter a path for a network printer here. Select "Network"

as the port.

Paper Size

Select the paper size used in the printer, e.g. A4 or Letter.

Draft Mode

Define the quality of the graphics printout. If the option is activated, printout is performed in

draft quality. If deactivated, the printout is in high quality.

Color

Define if a color printer will print in color or black and white.

Print Range

Define whether only the selected area should be printed or the entire contents.

Orientation

Define whether the page should be printed in Portrait or Landscape,

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Margins

The margin values entered here are ignored by the HMI device.

Note

If a serial printer is connected, the following printer settings are required:

- RS 232, whereby only the RxD, TxD and GND signals are required,

- 8 data bits

- 1 stop bit

- No parity

- Baud rate between 9600 and 57600, printer-dependent

- XON / XOFF protocol.

Default setting

When the HMI device is supplied, the following default settings are defined:

• Printer: EPSON 9 matrix printer

• Port: IF2

• Baud rate: 9600 bps

See also

Basic principles (Page 6-17)

Interface description (Page 12-8)

Open Control Panel (Page 6-2)

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-13

6.2.8 Regional Settings

"Regional Settings" option

Region-specific settings can be defined here. for example:

• Date and time format display

• Displaying numbers

The factory settings on the HMI device are German format.

Note

The settings defined in the "Regional Settings" option do not cause a change of languages in

the Windows CE dialogs, e.g. the Control Panel. English is always used.

See also

Open Control Panel (Page 6-2)

6.2.9 Screen Saver

"Screensaver" option

It is possible to define a period of time (in minutes) for automatic activation of the

screensaver on the HMI device. The screensaver settings are defined in the "Screensaver"

option of the Windows CE Control Panels.

Figure 6-7 "Screen Saver" dialog

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

The screen saver is automatically activated if the HMI device is not operated within the

defined period of time.

If a value of 0 is entered, the screen saver is deactivated.

Note

When the screensaver is activated, the back-lighting is automatically dimmed.

The screen saver is deactivated on pressing any key or touching the touch screen. The

function assigned to that key/button is not triggered.

Dim back-lighting

For technical reasons, the brightness of the screen back-lighting is reduced with increased

operational use. To increase the service life of the back-lighting, use the "Screensaver"

option in the Windows CE Control Panel to set the period of time after which the back-

lighting should be dimmed.

The back-lighting is automatically reduced if the HMI device is not operated within the

defined period of time.

On entering the value 0, dimming of the back-lighting is deactivated.

Notice

The screen can still be viewed with a reduced back-lighting.

The back-lighting is reactivated on pressing any key or touching the touch screen. The

function assigned to that key/button is triggered.

See also

Open Control Panel (Page 6-2)

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-15

6.2.10 System

"System" option

The "System" option can be used to define the size of the memory for the DRAM file system

(storage memory). It defines how much memory can be used by the applications. Values can

be modified using a slider control. The standard amount of memory in the DRAM file system

for applications is 6 Mb.

Figure 6-8 "System Properties" dialog

Caution

If too much DRAM file memory is provided, WinCC flexible runtime has too little working

memory available. There is no guarantee that your project will run properly if settings are

wrong.

Note

Operation of additional applications together with WinCC flexible

The memory requirements of projects in WinCC flexible has changed in comparison to

ProTool.

If user-specific additional applications should be operated on the HMI device together with a

WinCC flexible project, the functionality required on the HMI device must be tested and, if

necessary, the scope of the project or additional application reduced.

Operating system and configuration

6.2 Windows CE Control Panel

MP 370 (WinCC flexible)

6-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

See also

Open Control Panel (Page 6-2)

6.2.11 UPS

Uninterruptible power supply (UPS)

To prevent the loss of data in the event of a power failure, a UPS can ensure a controlled

shutdown of the HMI device. An external UPS detects when the power supply has failed and

signals this to the HMI device via the serial interface.

The UPS can only be loaded as an option.

"UPS" option

The UPS driver is installed as an add-on using the ProSave tool. The associated UPS icon

only appears in the Windows CE Control Panel after it has been installed via ProSave.

Figure 6-9 "UPS Properties" dialog

It is possible to define how long the power failure may continue without the runtime being

shut down. The driver is suitable for the SITOP DC-UPS Module A.

See also

Open Control Panel (Page 6-2)

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-17

6.2.12 Volume & Sounds

"Volume & Sounds" option

This is used to change the settings for acoustic signals and operating acknowledgement.

The "Volume" tab includes the following options:

• acoustic acknowledgement for touch operation

• volume control

The "Sounds" tab is irrelevant for runtime settings.

See also

Open Control Panel (Page 6-2)

6.3 Network operation

6.3.1 Basic principles

Purpose

The standard HMI device is equipped with an on-board Ethernet interface. Implementing the

network function enables the HMI device to be used for:

• Logging data via the network

• Printing via a network printer

• Storing recipe data records in the network

• exporting recipe data records in the network

• importing recipe data records from the network

• Transferring projects

• Backing up data

Notice

The HMI device can only be implemented in TCP/IP networks.

The HMI device only has client functionality in the PC network. This means that users

can access files of a subscriber with TCP/IP server functionality from the HMI device via

the network. However, it is not possible to access files on the HMI device via the network

from a PC.

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

6-18 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Note

Information on communication using SIMATIC S7 via Ethernet is provided in the "WinCC

flexible Communication" user manual.

Requirements

Within a TCP/IP network, computers are addressed by means of network names. These

network names are translated from a DNS or WINS server to TCP/IP addresses. Direct

addressing via TCP/IP addresses is not currently supported by the operating system.

Therefore, to ensure the functionality of the HMI device in a TCP/IP network, it is useful to

employ a DNS or WINS server. Appropriate servers are available in common TCP/IP

networks. Please contact your network administrator.

Printing via a network printer

The HMI device's operating system does not support the direct alarm logging via a network

printer. All other printer functions such as hardcopy or shift log, are possible via the network

without restriction.

6.3.2 Configuring the HMI device for network operation

Overview

The HMI device must be appropriately configured before setting into network operation. The

configuration is basically divided into the following steps:

• Set computer name of the HMI device

• Configure the network address.

• Set login information

• Save settings

Preparations

Before beginning the configuration, request the specific network parameters from the

network administrator. The following information is of particular interest:

• Does the network use DHCP for dynamic assignment of network addresses? If not, get a

new TCP/IP network address for the HMI device.

• What is the TCP/IP address of the default gateway?

• Which DNS addresses has the name server?

(If DNS is used in the network)

• Which WINS addresses has the name server?

(If WINS is used in the network)

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-19

Procedure

The following instructions describe how to define the general settings. Additional steps or

procedures may be necessary depending on the network infrastructure.

1. Open the Control Panel.

2. Set computer name of the HMI device.

In order to identify the HMI device within the network, it must be assigned a unique name

(device name) within the network using the Control Panel option "Communication"

Apply the settings and close the dialog by pressing <ENTER>.

3. Configure the network address.

– Use the "Network" option to open the network configuration.

– Select an appropriate network driver in the "Adapters" tab.

Select "Onboard LAN" for HMI devices with an integrated Ethernet card. Select

NE2000-compatible driver for other network cards.

– Press the "Properties" button in order to configure the network characteristics of the

network card used.

Complete the dialog according to the network driver selected.

– If your network uses DHCP, skip this step.

Select the "IP Address" tab then the "Specify an IP Address" option.

Enter the TCP/IP address of the HMI devices (e.g. 233.239.2.100), subnet mask (e.g.

255.255.255.0) and default gateway (e.g. 223.239.2.200).

– Enter the name server address of the network in the "Name Servers" tab.

Close the dialog with <ENTER> or press "OK" to apply the settings.

4. Set login information.

In order to correctly log on to the network, enter your user permissions in the

"Identification" tab. Enter the user name valid for the network or the network server and

the associated password (max. 8 characters).

If the network administrates users via domain controllers, enter the relevant domain

controller name.

Close the dialog with <ENTER> or press "OK" to apply the settings.

5. Save the settings.

– Switch off the HMI device.

– Before switching the HMI device on, insert the network cable in the corresponding

interface so that a unique IP address can be assigned during the start-up phase.

– Switch the HMI device on again.

See also

Open Control Panel (Page 6-2)

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

6-20 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

6.3.3 Test network

Procedure

When the HMI device has been configured for network operation, connect the network

server via Windows Explorer to test the network. Proceed as follows:

1. Start Windows Explorer via the Windows CE Start menu.

– Keyboard unit:

The Windows CE Start menu can be opened by pressing the key combination CTRL +

ESC .

– Touch panel unit:

– The Windows CE Start menu can be opened by pressing the button twice

(locking key) on the alphanumeric screen keyboard.

Select the "Windows Explorer" application from the "Programs" program group.

2. Use the "Address" input field to enter the UNC name of the folder or drive provided on the

server.

Example:

The server is called: mrnbg2

The name provided is: data

The resulting UNC name is: \\mrnbg2\data

Note

The use of TCP/IP addresses to address PCs is not supported by the operating system.

For example, the use of the UNC names "\\130.170.10.45\data" is not permitted.

3. After entering the UNC name, press the <ENTER> key.

Result

When all the network settings are correct, Windows Explorer displays the files located under

the directory provided on the TCP/IP server.

Note

In addition, the network program "ipconfig" is available in the operating system.

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 6-21

See also

Configuring the HMI device for network operation (Page 6-18)

6.3.4 Configuring network access

Requirements

The network is set up on the HMI device.

Procedure

In order to use the network functions in the WinCC flexible configuration software, specify

the relevant UNC assigned names at those points where paths have been entered for files or

directories.

Example 1: Logs

If you want to perform logging on the server in the example above, replace the predefined

archive memory location "\Storage Card\Logs" with the UNC assigned name for the server,

e.g. "\\mrnbg2\daten\Logs".

Example 2: Recipe data records

In order to store recipe data records in the network, replace the predefined path name

"\Flash\Recipes" with the UNC assigned name for the server, i.e. "\\mrnbg2\data\recipes".

The same applies for exporting and importing recipe data records using the functions

"ExportDataRecords" and "ImportDataRecords". In this case, replace the parameter "File

name" with the UNC assigned name for the server.

See also

Configuring the HMI device for network operation (Page 6-18)

Test network (Page 6-20)

Operating system and configuration

6.3 Network operation

MP 370 (WinCC flexible)

6-22 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-1

Prepare and backup project 7

7.1 Transfer project to the HMI device

7.1.1 Commissioning for the first time

Introduction

When commissioning for the first time, there is no configuration on the HMI device. In order

to transfer the necessary project data and the runtime software from the configuration

computer to the HMI device, proceed as follows, observing the sequence.

Notice

When starting the first time, observe the safety information on reverse poling.

Caution

Always terminate the runtime software before switching off the voltage supply in order to

prevent loss of data.

Press the operating element linked to the "StopRuntime" system function in the project to

stop runtime. Wait until the HMI device displays the loader and then switch off the power

supply.

Note

During the commissioning phase, it is possible to connect an external USB keyboard or

mouse via the USB interface.

Procedure

1. Connect the HMI device to the configuration computer using a suitable standard cable.

Use one of the following interfaces depending on the type of transfer:

– IF2 (serial)

– IF1B (MPI/PROFIBUS DP)

– USB

Prepare and backup project

7.1 Transfer project to the HMI device

MP 370 (WinCC flexible)

7-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

– Ethernet

Transfer via modem is also possible.

Default setting: Serial connection

2. Switch on the power supply to the HMI device.

When the HMI device is started up, the system automatically switches from the Loader to

transfer mode.

3. Press the "Cancel" button to switch to the Loader.

4. Press the "Control Panel" button to switch to the Windows CE Control Panel.

5. Adapt the interface setting (serial, MPI, USB or Ethernet) in the transfer settings.

Default setting: Serial connection

6. Close the Control Panel and switch to the transfer mode.

7. Start the project transfer operation on the configuration computer. Please refer to the

"WinCC flexible" user manual for more information on the settings required on the

configuration computer for the transfer operation.

Result

The configuration computer checks the connection to the HMI device. If the connection is not

available or defective, the configuration computer issues the corresponding error message.

If a transfer operation from the configuration computer is terminated as a result of a

compatibility conflict, the operating system of the HMI device must be updated.

If the connection is correct, the new project data are transferred to the HMI device. Following

successful transfer, the project is started and the Start screen of the transferred project

appears.

Set date/time

The date and time must be updated in the following cases:

• Initial startup

• If the HMI device is disconnected from the power supply for an extended period without a

backup battery

See also

Transfer mode options (Page 7-5)

Connecting the power supply (Page 4-15)

HMI device loader (Page 6-1)

Operating touch objects (Page 9-2)

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-3

7.1.2 Recommissioning

Purpose

When recommissioning, the existing configuration on the HMI device is replaced by another.

To this end, a new project is transferred from the configuration computer to the HMI device.

The procedure for transferring the project required for operation from the configuration

computer to the HMI device is described in "Transfer".

The following options are available for switching the HMI device to transfer mode:

• Starting transfer mode manually during the HMI device startup phase

• Starting transfer mode manually by pressing the applicable operating element in the

project when the HMI device is in operation

• Starting transfer mode automatically while the HMI device is in operation

7.2 Transfer

7.2.1 Start transfer manually

Procedure

1. Connect the HMI device to the configuration computer using a suitable standard cable.

Use one of the following interfaces depending on the type of transfer:

– IF2 (serial)

– IF1B (MPI/PROFIBUS DP)

– USB

– Ethernet

Transfer via modem is also possible.

2. Switch on the power supply to the HMI device.

3. Adapt the interface setting (serial, MPI, USB or Ethernet) in the transfer settings.

4. Close the Control Panel and switch to the transfer mode.

5. Start project transfer on the configuration computer.

Result

The configuration computer checks the connection to the HMI device. If the connection is not

available or is faulty, the configuration computer issues an error alarm to that effect.

If downloading from the configuration computer is terminated as a result of a compatibility

conflict, the HMI device's operating system must be updated.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

7-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

If the connection is correct, the new project is transferred to the HMI device. Following

successful transfer, the project is started and the Start screen of the transferred project

appears.

See also

Transfer mode options (Page 7-5)

Update operating system (Page 7-18)

7.2.2 Start transfer automatically

Overview

The HMI device can automatically switch to transfer mode during normal operation when a

transfer is started on the connected configuration computer. The transfer operation is

completed without intervention on the HMI device. Therefore, this option is particularly suited

for the test phase of a new project.

To switch to transfer mode from active operation, open the "Transfer Settings" window on

the HMI device and select the required connection and the corresponding "Remote Control"

function.

Notice

When the "Remote Control" option is activated, Runtime is automatically ended and the

switch is made to transfer mode. Runtime cannot be ended if dialogs are open or a transfer

operation has been started on the HMI device.

Close the dialog or cancel the transfer process on the configuration computer.

Following the start-up phase, disable the automatic transfer option to prevent inadvertently

switching the HMI device to transfer mode in a running system, thereby ending Runtime. To

do this, deactivate the "Remote Control" options in the transfer settings defined for the HMI

device.

See also

Transfer mode options (Page 7-5)

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-5

7.2.3 Transfer mode options

Transfer mode options

The following options can be set for transfer mode:

• The HMI device can be switched to transfer mode automatically when in normal operation

as soon as a transfer is started on the connected configuration computer.

• Select a specific connection type so that transfer can only occur either via a serial

connection, MPI/PROFIBUS-DP, USB or Ethernet connection.

Note

Do not make any other changes if the Runtime software is running or the HMI device is in

transfer mode.

Setting the communication channel

The "Channel" tab in the Transfer Settings menu can be used to activate the required

communication channel and the "Remote Control" checkbox. In addition to the serial

communication channel, a second channel can also be selected for transfer of data from the

configuration computer to the HMI device.

Figure 7-1 "Transfer Settings" dialog, "Channel" tab

Press the "Advanced" button to define the following settings:

• For transfer MPI or PROFIBUS-DP, define the "Address" bus parameter and

"Transmission Rate" and "Highest Station" network parameters.

• Define the driver for transfer via Ethernet.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

7-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Warning

When the "Remote Control" checkbox is active, ensure that the HMI device is not

inadvertently switched to transfer mode from the configuration computer.

In the case of PROFIBUS DP, changes may only be made here for commissioning

purposes.

For each modification to the PROFIBUS DP settings, the HMI devices set up only one

corresponding standard bus parameter set. Under unfavorable conditions, this can lead

to faults on the PROFIBUS.

In order to calculate the bus parameters exactly, the entire bus topology must be known.

Correct definition of the bus parameters for Runtime is automatically ensured through the

integrated operation of WinCC flexible in SIMATIC STEP 7.

Notice

If a serial printer is connected to the HMI device, deactivate it by selecting "Remote

Control" checkbox for the serial communication channel. Otherwise, printing is not

possible.

When a configuration is transferred from the configuration computer to the HMI device,

enable a communication channel using the "Enable Channel" option.

If an interface is occupied by other programs, transfer cannot take place via that

interface.

Note

The bus parameters for the MPI transfer, e.g. MPI address, baud rate, etc., are read from

the project currently loaded on the HMI device.

The settings for MPI transfer can be modified. To do this, you must first end Runtime,

modify the settings, and switch to transfer mode. When Runtime is started subsequently,

the bus parameters are overwritten with the values from the project.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-7

Transfer mode directories

The "Directories" tab can be used to specify the following paths (refer to figure below).

Figure 7-2 "Transfer Settings" dialog, "Directories" tab

Project File

The predefined storage location for the project file can be changed here. The internal Flash

memory or external Flash cards can be set. During the next transfer operation, the project

will be stored in the storage location specified.

Project Backup

Here, you change the default storage location for the source file of your project. This file can

be used for restoring (uploading) the configuration. External Flash cards or network

connections can be set.

Autostart application

• Path

The memory location for Runtime is defined here. This is the application used to run your

project in Windows CE.

• Wait

Here, you set the amount of time (in seconds) that the Loader is to be displayed before

Runtime is started (1 s, 3 s, 5 s, 10 s, or constantly). If Runtime is not available, the

device automatically switches to transfer mode.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

7-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Notice

With the exception of "Wait," do not change the default settings in these fields if you are

working with WinCC flexible. Otherwise, the HMI device can no longer start your project.

Press the "OK" button or <ENTER> key to confirm the settings currently defined for the

transfer options. Ensure that no buttons have been selected. The dialog is closed and the

Windows CE Control Panel is displayed.

Press the close symbol or <ESC> key to close the dialog and open the Windows CE Control

Panel. Any modifications made to the settings are rejected.

Note

If the HMI device is in transfer mode while changes are made to the transfer settings, the

settings only take effect after the transfer function is restarted. This can occur when the

Control Panel is selected via the Windows Start menu in order to modify the transfer

properties.

7.2.4 Testing the project

Introduction

There are two options on the HMI device for testing a new project:

• Test project offline

Testing offline means that communication between the HMI device and PLC is

interrupted while the test is being carried out.

• Test project online

Testing online means that the HMI device and PLC communicate with each other during

the test.

It is advisable to perform both tests starting with the "Offline test" followed by the "Online

test."

Note

Testing on a configuration computer

A project can also be tested on a configuration computer using the Simulator. Detailed

information on this is available in the "WinCC flexible" user guide and in the WinCC flexible

online help.

You should always test the project afterwards on the HMI device where the project will be

used.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-9

Check the following:

1. Check that configured screens are displayed correctly

2. Check screen hierarchy.

3. Test input objects

4. Test softkeys.

5. Test that tag data can be entered.

The test increases the certainty that the project will run error-free on the HMI device.

Conditions for the offline test

• The project is on the HMI device.

• The project is offline.

Open the selected project on the configuration computer. Select "Communication >

Connections" and switch to "Online: Off". Transfer the project to the HMI device.

Alternatively, the operating mode can be changed by means of an operating element in

the project. Use the operating element to switch the project offline.

Note

During the test phase, it is recommended that the transfer operation be started during

operation.

Procedure

Use "Offline" mode to test the individual project functions on the HMI device without them

being affected by the PLC. PLC tags are, therefore, not updated.

Test the project operating elements and displays to the extent possible without connecting to

the PLC. Proceed as follows:

1. Check that configured objects are displayed correctly.

2. Check screen hierarchy.

3. Check input fields.

4. Test softkeys.

Conditions for the online test

• The project is on the HMI device.

• The project is online.

Open the selected project on the configuration computer. Select "Communication >

Connections" and switch to "Online: On". Transfer the project to the HMI device.

Alternatively, the operating mode can be changed by means of an operating element in

the project. Use the operating element to switch the project online.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

7-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Note

During the test phase, it is recommended that the transfer operation be started during

operation.

Procedure

Use "Online" mode to test the individual project functions on the HMI device with influence

being exerted by the PLC. PLC tags are updated in this case.

Test the project operating elements and displays. If offline testing has not yet been

performed, proceed as follows:

1. Check that configured objects are displayed correctly.

2. Check screen hierarchy.

3. Check input fields.

4. Test softkeys.

Test all of the objects in the loaded project for which communication with the PLC is

necessary:

• Alarms

• Alarm logging

• Recipes

• Screen selection by PLC through PLC job

• Print functions

7.2.5 Uploading project

Introduction

During transfer, generally only the run-capable configuration (*.fwx) is transferred to the HMI

device. If the original project file is to be used for further development of the configuration or

for fault analysis, it must remain on the configuration computer.

The project and associated source file (*) can be stored on the HMI device. It can be

retrieved (transferred back) if necessary.

After uploading a project, it can be analyzed and modified. This is of particular importance if

• the original configuration computer cannot be accessed, or

• the project source file is no longer available.

Prepare and backup project

7.2 Transfer

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-11

Requirements

The following conditions must be fulfilled in order to retrieve a project:

• The HMI device is connected to a configuration computer.

• The associated source file is stored on the HMI device.

• The "Enable Upload" option must be selected in order for the project file to be transferred

from the configuration computer to the HMI device.

This option can be activated in WinCC flexible in "Project ▶ Transfer ▶ Transfer Settings".

• A memory card is inserted in the HMI device.

Downloading and uploading

In the case of transfer, including transfer of the source file, the project file is transferred to

the HMI device.

Following uploading onto the configuration computer, the *.pdz file is compressed by the

WinCC flexible configuration software. The project is then available in HMI format on the

configuration computer and can be edited.

Notice

Version number

The uploaded project file can only be opened with a configuration software whose version

number is greater than or equal to that of the configuration software used to create the

project.

Test source file

WinCC cannot determine if the source file on the HMI device was generated from the project

run on it. If a transfer is performed at any time without the "Upload" option activated, only the

project is transferred. The existing source file may be from a previously transferred project.

Procedure

1. Select the menu command "Project ▶ Transfer ▶ Communication Settings" on the

configuration computer in WinCC flexible.

The "Communication Settings" dialog box is opened.

2. Select the required HMI device type and connection type between the HMI device and

the configuration computer.

3. Define the connection parameters.

4. Select "OK".

5. Switch the HMI device to transfer mode in the loader.

6. On the configuration computer, use WinCC to start the back transfer using the "Project ▶

Transfer ▶ Back Transfer" menu command.

The project is opened on the configuration computer.

Prepare and backup project

7.3 System settings

MP 370 (WinCC flexible)

7-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Result

The uploaded project is opened on the configuration computer. Save the project, if

necessary.

7.3 System settings

7.3.1 Set language

Language-dependent objects

When the project is transferred from the configuration computer, up to five languages can be

transferred to the HMI device simultaneously. The Asian language variants are also

supported. You can switch between the individual languages online at any time and display

language-dependent objects within Runtime, e.g., texts or formats, in another language.

The following are language-dependent:

• Alarms

• Screens

• Text lists

• Help texts

• Date/time

• Decimal symbol

• Static texts

Requirements

If during operation you want to change the language in which the project will appear on the

HMI device, the following conditions must be met:

• The language must be available for the configuration on the HMI device.

The languages available on the HMI device are defined during configuration.

• An operating element for switching languages must have been configured.

Select languages

Immediately after the operating element for switching languages is activated, all of the

language-dependent objects are displayed in the new language.

Two different types of language change can be configured:

1. Each time the operating element for switching languages is activated, the HMI device

advances cyclically by one language.

2. Activating the operating element for switching languages causes the HMI device to switch

to a specific language.

Prepare and backup project

7.3 System settings

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-13

7.3.2 Set operating mode

Conditions for changing operating modes

In order to switch between the operating modes described below on the HMI device, the

relevant function must be configured and linked to an operating element.

Operating modes

The HMI device is designed for the following operating modes:

• Offline mode

• Online mode

• Transfer mode

An operating element in the project can be used to set "Offline" and "Online" operating

modes on both the configuration computer and the HMI device.

Transfer mode must have been configured as an operating element.

Offline mode

In this mode, there is no communication connection between the HMI device and PLC. The

HMI device can be operated but data cannot be transmitted to the PLC or received from the

PLC.

Online mode

In this mode, a communication connection between the HMI device and PLC exists. When

using this mode, processes in progress can be operated and visualized without restriction.

Transfer mode

In this mode, you can transfer a project from the configuration computer to the HMI device.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

7.4 Other transfer functions

7.4.1 Functions

ProSave Service Tool

The ProSave Service Tool is supplied with WinCC flexible. ProSave provides all the

functions that are necessary to transfer data between the configuration computer and HMI

device. These include:

• Saving data (backup)

• Retrieving data (restore)

• Updating the operating system (OS update)

• Transferring authorizations

• Transferring options

ProSave can be installed together with WinCC flexible or as a stand-alone tool on the

configuration computer. Further information on ProSave is available in the "WinCC flexible"

user's guide.

ProSave functions in WinCC flexible

ProSave is normally installed on the configuration computer together with WinCC flexible.

The entire function range of ProSave is available within WinCC flexible in the "Project ▶

Transfer" menu. In this way, all the necessary specifications, e.g. target device and

download settings, are assumed from the project.

Stand-alone ProSave

ProSave can also be installed as a stand-alone application. In this case, the settings relating

to the HMI device and the transfer must be defined in the ProSave user interface and match

the HMI device settings.

The advantage of stand-alone ProSave is that data backup and restore operations can be

performed without WinCC flexible via the following transfer channels:

• Serial

• MPI/PROFIBUS DP

• USB

• Ethernet

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-15

7.4.2 Backup and Restore

Introduction

WinCC flexible or the ProSave Service Tool can be used to back up and restore projects,

recipes, and passwords.

If the service tool was installed together with WinCC flexible, it can be called by selecting

"SIMATIC ▶ ProSave" in the "Start" menu on the configuration computer.

ProSave is an executable program which can run without WinCC flexible. ProSave can, thus,

be run without a WinCC flexible license.

Requirements

• The HMI device is connected to a configuration computer.

• WinCC flexible or ProSave is installed on the configuration computer.

Notice

Close all open applications on the configuration computer before starting Backup or

Restore.

Backup

During the backup process, the project is transferred from the HMI device Flash memory to

the configuration computer.

There are two ways to make a backup copy:

• Backup using stand-alone ProSave

• Backup using WinCC flexible

Notice

Licenses on the HMI device are not included in the backup.

The procedure for the backup differs in terms of the operations performed on the

configuration computer.

Procedure - backup using stand-alone ProSave

1. Start ProSave on the configuration computer using the Windows Start menu.

2. Use the "General" tab to select the required HMI device and connection type with the

appropriate connection parameters.

3. Use the "Backup" tab to select the data to be saved:

– "Recipes" or

– "Passwords"

– "Complete backup"

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4. Select the folder where the *.psb backup file should be saved.

5. Configure the required transfer channel on the HMI device.

6. Switch the HMI device to transfer mode.

7. Start the backup operation in ProSave using the "Start Backup" button.

A status display monitors the progress of the data transfer.

Procedure - backup using WinCC flexible

1. In WinCC flexible, select "Project ▶ Transfer ▶ Transfer Settings" in the "Select HMI

devices for transfer" dialog to select the connection type with the appropriate connection

parameters.

2. Open the "Backup Settings" dialog in WinCC flexible using the "Project ▶ Transfer ▶

Backup" menu command.

3. Select the data to be saved:

– "Recipes" or

– "Passwords" or

– "Complete Backup"

4. Select the folder where the *.psb backup file should be saved.

5. Configure the required transfer channel on the HMI device.

6. Switch the HMI device to transfer mode.

7. Start the backup operation in WinCC flexible using the "OK" button.

A status display monitors the progress of the data transfer.

Result

When the transfer is successfully completed, a message appears. The project is copied on

the configuration computer.

Restore

In the case of a restore process, the data backup stored on the configuration computer is

reloaded into the internal Flash memory of the HMI device.

There are two ways to restore the data:

• Restore using stand-alone ProSave

• Restore using WinCC flexible

Notice

Data loss

The files in the user memory of the HMI device are deleted during this process. This also

applies to the licenses on the HMI device. Therefore, save the licenses elsewhere before

starting the restore process.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-17

The restore procedure differs in terms of the operations performed on the configuration

computer.

Procedure - restore using stand-alone ProSave

1. Start ProSave on the configuration computer using the Windows Start menu.

2. Use the "General" tab to select the required HMI device and connection type with the

appropriate connection parameters.

3. In the "Restore" tab, select the path of the file to be restored.

"Content" indicates the HMI device for which the backup was created and the type of

backup data contained in the file.

4. Configure the required transfer channel on the HMI device.

5. Switch the HMI device to transfer mode.

6. Start the restore operation in ProSave using the "Start Restore" button.

A status display monitors the progress of the restore process.

Procedure - restore using WinCC flexible

1. In WinCC flexible, select "Project ▶ Transfer ▶ Transfer Settings" in the "Select HMI

devices for transfer" dialog to select the connection type with the appropriate connection

parameters.

2. Open the "Restore Settings" dialog in WinCC flexible using the "Project ▶ Transfer ▶

Restore" menu command.

3. In the "Open" field, select the path of the file to be restored.

"Content" indicates the HMI device for which the backup was created and the type of

backup data contained in the file.

4. Configure the required transfer channel on the HMI device.

5. Switch the HMI device to transfer mode.

6. Start the restore process in WinCC flexible using the "OK" button.

A status display monitors the progress of the restore process.

Result

When the transfer is successfully completed, a message appears. The project is available on

the HMI device again.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-18 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

7.4.3 Update operating system

Introduction

Conflicts may occur when using the HMI device due to the use of different versions of the

configuration software and the HMI device image present on the HMI device. In such a case,

transfer of the project is stopped by the configuration computer and a message indicating a

compatibility conflict appears. The operating system on the HMI device must then be

updated. For this purpose, a current HMI device image must be transferred to the HMI

device. The image contains the required operating system.

The procedure is described below.

Requirements

• The HMI device is connected to the configuration computer according to the selected

connection type.

• WinCC flexible or ProSave is installed on the configuration computer.

Notice

Data loss

When the operating system is updated, all of the existing data on the HMI device, such

as project, applications, passwords, and recipes, are deleted.

There are two different procedures for updating the operating system:

• Updating the operating system using stand-alone ProSave

• Updating the operating system using WinCC flexible

If an operating system update should be performed using WinCC flexible, all the general

settings, such as HMI device and transfer settings, are assumed from the project.

Update operating system

There are two types of operating system updates:

• An update on an HMI device on which an operating system already exists

In this case, the operating system update is executed without selecting the "Boot" check

box.

• An update on an HMI device on which there is no operating system

In this case, the operating system update is executed with the "Boot" check box selected.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-19

Procedure – update operating system without Booting

When updating the operating system without "Booting", the configuration computer

communicates with the HMI device via its operating system.

Proceed as follows in order to adapt the operating system on the HMI device to the

configuration software version used:

1. Start WinCC flexible from the Windows Start menu on the configuration computer and

open a project, or start ProSave from the Windows Start menu.

2. When using WinCC flexible, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command or, using ProSave, select the existing HMI device on the "General" tab.

3. Select the connection.

4. Enter the connection parameters

5. In WinCC flexible, select the "Project ▶ Transfer ▶ Update Operating System" menu

command, or in ProSave, select the "OS Update" tab in ProSave.

6. Clear the "Boot" check box if it is selected.

7. In "Image path," select the directory containing the image file (file extension *.img)

belonging to the HMI device.

8. Select the "Open" button.

When the image file has been opened successfully, various version information appears

in a window.

9. Configure the required transfer channel on the HMI device.

10. Switch the HMI device to transfer mode.

11. Start the operating system update on the configuration computer using the "Update OS"

button.

The time this process takes differs depending on the data channel selected. A status

display will monitor the transfer's progress.

Result

When the operating system update is successfully completed, a message appears.

The HMI device no longer contains a project.

Procedure – update operating system with Booting

When the operating system is updated with "Booting", the configuration computer

communicates with the boot loader of the HMI device.

Connect the HMI device to the configuration computer.

Notice

An operating system update with booting is only possible via a serial connection.

After starting the operating system update, the HMI device must be rebooted so that the HMI

device establishes contact via the serial interface.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-20 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Proceed as follows in order to adapt the operating system on the HMI device to the

configuration software version used:

1. Switch off the power supply to the HMI device.

2. On the configuration computer, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command in WinCC flexible, or select the existing HMI device on the "General" tab in

ProSave.

3. Select the connection.

4. Enter the connection parameters

5. In WinCC flexible, select the "Project ▶ Transfer ▶ Update Operating System" menu

command, or in ProSave, select the "OS Update" tab in ProSave.

6. Select the "Boot" check box if it is cleared.

7. In the image path, select the directory containing the image file (file extension *.img)

belonging to the HMI device.

8. Select the "Open" button.

When the image file has been opened successfully, various version information appears

in a window.

9. Start the operating system update using the "Update OS" button.

10. Switch on the power supply to the HMI device again.

This starts the update. The time this process takes differs depending on the data channel

selected. A status display will monitor the transfer's progress.

Result

When the operating system update is successfully completed, a message appears.

The HMI device no longer contains a project.

7.4.4 Transferring authorizations

Introduction

To protect the software, licenses (authorizations) on an Authorization disk can be transferred

to and transferred back from the HMI device.

The authorization disk is supplied with the respective option, with ProAgent/MP for example,

with ProAgent/MP for example.

Requirements

• The HMI device is connected to the configuration computer according to the selected

connection type.

• WinCC flexible or ProSave is installed on the configuration computer.

• Insert the Authorization disk containing the licenses to be transferred in the disk drive of

the configuration computer.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-21

The ProSave Service Tool can be used to transfer authorizations. An advantage of this is

that the authorization can be transferred without calling in WinCC flexible.

There are two methods of transferring an authorization:

• Transferring an authorization using stand-alone ProSave

• Transferring an authorization using WinCC flexible

If an authorization transfer should be performed using WinCC flexible, all the general

settings, such as HMI device and transfer settings, are assumed from the project.

Procedure - transferring an authorization to the HMI device

Transferring an authorization to the HMI device

1. Start WinCC flexible from the Windows Start menu on the configuration computer and

open a project, or start ProSave from the Windows Start menu.

2. When using WinCC flexible, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command or, using ProSave, select the existing HMI device on the "General" tab.

3. Select the connection.

4. Enter the connection parameters

5. Select the menu command "Project ▶ Transfer ▶ Authorizations" in WinCC flexible or

select the "Authorize" tab in ProSave.

6. Select the authorization to be transferred to the HMI device from the "Choices" options.

7. Configure the required transfer channel on the HMI device.

8. Switch the HMI device to transfer mode.

9. Press the ">>" button to start transferring the authorization onto the configuration

computer.

Result

The authorization is transferred to the HMI device. The option as to which authorization is

required can now be defined on the HMI device.

Procedure - transferring authorization back from the HMI device

Transferring an option back from the HMI device:

1. Start WinCC flexible from the Windows Start menu on the configuration computer and

open a project, or start ProSave from the Windows Start menu.

2. When using WinCC flexible, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command or, using ProSave, select the existing HMI device on the "General" tab.

3. Select the connection.

4. Enter the connection parameters

5. Select the menu command "Project ▶ Transfer ▶ Authorizations" in WinCC flexible or

select the "Authorize" tab in ProSave.

6. Configure the required transfer channel on the HMI device.

7. Switch the HMI device to transfer mode.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-22 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

8. Press the "Device Status" button on the configuration computer to display all the

authorizations currently installed on the HMI device.

9. Select the authorizations under "Installed Authorizations" to be transferred from the HMI

device.

10. Press the "<<" button to start transferring the authorizations back.

Result

The authorization is transferred back from the HMI device. The option as to which

authorization is required can no longer be used on the HMI device.

7.4.5 Transferring options

Introduction

Options specially developed for the HMI device, e.g. additional applications, can be installed

on the HMI device.

ProSave is supplied with the following options by default:

• Drivers for uninterruptible power supply

• Pocket Internet Explorer

Requirements

• The HMI device is connected to the configuration computer according to the selected

connection type.

• WinCC flexible or ProSave is installed on the configuration computer.

The ProSave Service Tool can be used to transfer authorizations. An advantage of this is

that the option can be transferred without calling in WinCC flexible.

There are two methods of transferring an option:

• Transferring an option using stand-alone ProSave

• Transferring an option using WinCC flexible

If an option transfer should be performed using WinCC flexible, all the general settings,

such as HMI device and transfer settings, are assumed from the project.

Procedure - transferring an option to the HMI device

Transferring an option to the HMI device

1. Start WinCC flexible via the Windows Start menu and open a project, or start ProSave via

the Windows Start menu.

2. When using WinCC flexible, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command or, using ProSave, select the existing HMI device on the "General" tab.

3. Select the connection.

4. Enter the connection parameters

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 7-23

5. Select the menu command "Project ▶ Transfer ▶ Options" in WinCC flexible or select the

"Options" tab in ProSave.

6. Select the options to be transferred to the HMI device from "Available options".

7. Configure the required transfer channel on the HMI device.

8. Switch the HMI device to transfer mode.

9. Press the ">>" button to start transferring the option.

Result

The option is transferred to the HMI device.

Procedure - transferring authorization back from the HMI device

Transferring an option back from the HMI device:

1. Start WinCC flexible from the Windows Start menu on the configuration computer and

open a project, or start ProSave from the Windows Start menu.

2. When using WinCC flexible, select the "Project ▶ Transfer ▶ Transfer Settings" menu

command or, using ProSave, select the existing HMI device on the "General" tab.

3. Select the connection.

4. Enter the connection parameters

5. Select the menu command "Project ▶ Transfer ▶ Options" in WinCC flexible or select the

"Options" tab in ProSave.

6. Configure the required transfer channel on the HMI device.

7. Switch the HMI device to transfer mode.

8. Press the "Device Status" button on the configuration computer to display all the options

currently installed on the HMI device.

9. Select the options under "Installed Options" to be transferred back from the HMI device

10. Press the "<<" button to start transferring the options back.

Result

The option is transferred back from the HMI device.

Prepare and backup project

7.4 Other transfer functions

MP 370 (WinCC flexible)

7-24 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 8-1

Runtime functionalities of a project 8

8.1 Screen objects

Overview

Runtime offers the following objects for operator control and display:

• Button

• Switch

• I/O field

• Graphic I/O field

• Symbolic I/O field

• Alarm indicator

• Alarm view

• Alarm window

• Recipe view

• Bar

• Trend view

• Slider control

• Gauge

• Date / time field

• Clock

• User view

• Status force

• Sm@rtClient view

• Symbol library

Runtime functionalities of a project

8.2 Alarms

MP 370 (WinCC flexible)

8-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

8.2 Alarms

Alarm classes

Alarms indicate events and states in the control process on the HMI. WinCC flexible

distinguishes the following alarm classes:

• Operation

Warning alarms indicate a process status, e.g. motor is ON. Warning messages are

configured.

• Error

Error alarms indicate operational errors such as excess motor temperature. Alarm

messages are configured. These are high-priority messages and must therefore be

acknowledged.

• System

System alarms are triggered by the HMI device. They are not configured. System alarms

provide information on operator errors or communication faults, for example.

• STEP 7 alarm classes

The alarm classes configured in STEP 7 are also available for the HMI device.

• Custom alarm classes

It is possible to configure further alarm classes.

Alarm buffer

All incoming, outgoing and acknowledged alarm events are logged to an internal volatile

buffer memory. The size of this alarm buffer depends on the type of HMI device.

Alarm protocol

When alarm logging is activated, alarm events are printed out directly on the printer.

It is possible to individually configure each alarm to specify whether it is to be reported (sent

to the printer).

Alarm log

Alarm events are stored in an alarm log, provided this log file is configured. The capacity of

the log file is limited by the storage medium and system limits.

Alarm view

Events stored in the alarm buffer and the alarm log can be displayed in the alarm view in

Runtime.

The alarm view is used to indicate process alarm events. Whether alarm events need to be

acknowledged or not is defined in your configuration data.

Runtime functionalities of a project

8.3 Tags

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 8-3

Alarm window

A configured alarm window shows all queued alarms, or alarms of the relevant alarm class

which require acknowledgement. The alarm window opens when a new alarm is received.

You can configure the order in which the alarms are displayed. You can choose to indicate

the alarms in ascending or descending order of their occurrence. The alarm window can also

be set to indicate the exact location of the fault, including the date and time of the alarm

event.

Alarm indicator

An alarm indicator icon is output on-screen if at least one error alarm is queued on the HMI

device.

The indicator flashes as long as unacknowledged alarms are pending. The displayed

number indicates the number of pending alarms.

8.3 Tags

Definition

Tags represent defined memory areas on the HMI device, to which values are written and/or

from which values are read. This action can be initiated on the controller, or by the operator

at the HMI device.

8.4 Logs

Overview

Alarm events and process values can be saved to log files.

Examples of alarm events are the incoming, acknowledged and outgoing events occurring

with an alarm message.

Process value logging is used for the following purposes, for example:

• Early detection of danger / fault states

• Increase of productivity

• Enhancement of product quality

• Optimization of maintenance cycles

• Documentation of processes

• Quality assurance

Runtime functionalities of a project

8.4 Logs

MP 370 (WinCC flexible)

8-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Memory options

Depending on the configuration, the logs are written to a file or stored in a database set up

for this purpose.

• Logging to a CSV file

The project engineer must have specified a folder path for storing the CSV file containing

your logged data. This references the storage location.

CSV format table columns are separated by separators, the table rows are terminated by

a line break character. This allows you to evaluate or edit your log data using an external

text editor or spreadsheet program, for example.

• Logging to a database

By storing your log files in a database, you can utilize the full database functionality for

further processing and analysis of the logged data.

Databases tested and released for WinCC flexible:

– MS Data Engine 97 and MS Data Engine 2000

– MS Access 97 and MS Access 2000

– MS SQL Server 7.0 and MS SQL Server 2000

Logging methods used in WinCC flexible Runtime:

• Circular log

• Segmented circular log

• Log with level-dependent system alarm

• Log file with data volume-based system alarm

Alarm logs

Alarms in the project indicate fault states and operating states of a process. They are

generally triggered by the controller. Alarms can be output to the HMI in the form of images.

WinCC flexible lets you log alarms and document operational states and error states of the

plant.

The following data are logged to the file:

• Date and time of alarm

• Alarm number

• Alarm tags (up to 8)

• Alarm status

• Alarm text (optional)

• Fault location (optional)

All alarms are assigned to a specific alarm class. All alarm classes can be logged.

Alarms can be logged either automatically, or by operator intervention.

The contents of log files can be output to the HMI, if a corresponding alarm view has been

configured.

Runtime functionalities of a project

8.5 Reports

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 8-5

Data logs

In Runtime, the process values are logged, processed and, depending on the project, written

either to files or to the log database.

Data logging is controlled by means of cyclic operations and events. Logging cycles are

used to ensure continuous acquisition and storage of the data. In addition, data logging can

also be triggered by events, e.g. when a value changes.

8.5 Reports

Overview

Logs are used to document process data and completed production cycles. The log content

and layout are specified in the project, as is the event triggering the printout of the report.

For example, a log can be configured for output at the end of a shift, in order to record

downtimes. A log can also be configured for the purpose of the documentation of product

testing or quality inspections (ISO 9000).

Edition

Reports are printed in Runtime either automatically, e.g. by means of a scheduler, or

manually, e.g. by means of a softkey.

Printing reports

Reports are output to the printer in graphic mode. The use of a serial printer is not

recommended because of the accumulated data volume.

For proper output, the printer must support the paper format and page layout of the report.

Note

The value of a tag in the report is read and output at the moment of printing. A substantial

time may elapse between printing out the first and the last page of a report consisting of

several pages. This may lead to the same tag on the last page being output with a different

value from that on the first page.

Runtime functionalities of a project

8.6 System functions and scripts

MP 370 (WinCC flexible)

8-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

8.6 System functions and scripts

Application

System functions and scripts are used in Runtime for the following purposes:

• To control the process

• To utilize the properties of the HMI device

• To make system settings on the HMI device online

In WinCC flexible, each system function and each script s linked to an object, such as a

button, field or screen, and an event. As soon as the event occurs, the system function is

triggered.

System functions

System functions are predefined functions that are used to implement many tasks in

Runtime, such as:

• Calculations, e.g. increase of a tag value by a specific or variable amount

• Logging function, such as starting a process value log

• Settings, such as changing the PLC or setting a bit in the PLC.

• Alarms, for instance after logon of a different user.

Scripts

Scripts may also be included in the project for specific applications which may require

additional functions. For the creation of scripts, WinCC flexible provides an interface to

Microsoft Visual Basic Script (VBScript). This allows you to integrate additional functions,

such as:

• Conversion of values, e.g. between different physical units (temperatures)

• Automation of production sequences

A script can control a production sequence by transferring production data to a PLC. The

status can be checked based on the returned values, and appropriate measures can thus

be initiated.

Events

The object and the selected function determine what events can be defined as triggers for

executing a system function.

For example, the events "Change value", "BelowLowerLimit" and "AboveUpperLimit" belong

to the "Tag" object. The "Loaded" and "Cleared" events are associated with the "Screen"

object.

Runtime functionalities of a project

8.7 Safety

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 8-7

8.7 Safety

Overview

Operation in Runtime is protected by the use of user groups, passwords and log-off times.

After you started Runtime, type in the user name and password in the login dialog.

User groups

The security concept of WinCC flexible is organized in several layers: It is based on

authorizations, user groups, and users.

• User groups are created for specific projects by the project engineer. The

"Administrators" group is included in all projects by default. User groups are assigned

authorizations. The authorization level required for an operation is specifically defined for

each individual object and function in the project.

• User accounts are created by the project engineer, or in Runtime by the administrator, or

by a user with the same rights, and are always assigned to one group only.

Users belonging to a user group with "Administration" authorization may create further user

accounts and assign these to a group.

Passwords

Only registered users may log in to Runtime by entering their user name and password. The

passwords can be assigned by the configuring engineer, by the "Admin" user (or by users

who have "Administration" authorization), or by the user himself.

Which functions a user may execute after login depends on which user group he/she is

assigned to.

After the project is transferred, only the administrator is authorized to create user accounts,

make user group assignments, and change passwords. Any further users assigned to the

"Administrator" group by the administrator may also carry out these tasks.

The list will be encrypted and saved on the HMI device to protect it from loss due to a power

failure.

Note

Depending on the transfer settings, changes to the password list are overwritten when the

project is transferred again.

Runtime functionalities of a project

8.8 Other operating functions

MP 370 (WinCC flexible)

8-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Log-off times

A log-off time is specified in the system for each user. If the time between any two user

actions, e.g, entering a value or pressing a key, exceeds this logoff time, the user is

automatically logged off. The user must then log on again to continue to operate Runtime.

User view

Use the User view to display the users present on the HMI device.

Export and import

All users, passwords, group assignments and logoff times furnished on the HMI device can

be exported and reimported on another HMI device, when the configuration is suitable. This

helps to you avoid having to enter all of the data again on another HMI device.

Notice

The currently valid passwords are overwritten during an import. The imported passwords are

valid immediately.

8.8 Other operating functions

Print functions

Print functions available in online mode: :

• Hardcopy

You can print the content of the currently displayed screen using the "Print screen"

system function in your configuration.

• Alarm protocol

All alarm events (incoming, outgoing, acknowledgment) are also output to a printer.

• Printing reports

Runtime functionalities of a project

8.8 Other operating functions

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 8-9

Note

Special, non-European characters

When printing alarms in languages other than Western European languages, some

characters are not printed correctly under certain circumstances. The print result is

dependent on the printer used.

Note

Printing via a network printer

Printing alarms on a network printer is not approved for Windows CE HMI devices. All

other functions have no restrictions, even over the network.

LED control

The light-emitting diodes (LED) in the function keys of the SIMATIC HMI devices can be

controlled from the PLC. A lit or flashing LED may signal, for example, the operator to press

a specific function key on the device.

Runtime functionalities of a project

8.8 Other operating functions

MP 370 (WinCC flexible)

8-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-1

Operating a project 9

9.1 Basic principles of operation

9.1.1 Basics for operation in Runtime

Introduction

The process control features are defined by the project configuration and the options

available on the HMI device. This section contains general information on the settings for

Runtime and for operation of predefined screen objects.

Screen objects provide general system functions. Screen objects can be used and

configured in screens in the project.

Runtime can be controlled with the keys, using the touch screen, or via the keyboard and

mouse, depending on the HMI device used.

Multiple key operation

Unintentional actions can be triggered by a multiple key operation.

• When you use a key device, you may not press more than two function keys

simultaneously.

• If you are using a touch screen device, you may only operate one touch object at a time.

Language switching

WinCC flexible allows a multilingual project configuration. Up to five of these project

languages can be loaded on the HMI device simultaneously.

Runtime allows you to change the languages, provided this function is configured.

Language-specific objects such as texts or formats are localized. The following objects may

contain language-relevant texts, for example:

• Alarms

• Screens

• Text lists

• Help texts

• Recipes

• Date/time

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

• Static texts

Objects in the template screen

Objects that should be available on each screen are configured in the template by the

configuring engineer, e.g., important process values or date and time.

An operating element that is present in the template is available in every screen. In the case

of touch screen devices, for example, a button in the template screen simulates a globally

effective function key.

Pictograms

In the case of keyboard devices, pictograms can be configured along the bottom and sides

of the screen.

Pictograms highlight the screen-specific functions of the function keys. Activating the

associated function key initiates the function symbolized by the pictogram.

9.1.2 Operating the touch panel (TP)

9.1.2.1 Operating touch objects

Operation

Touch objects are touch-sensitive operating objects on the HMI screen, e.g. buttons, I/O

fields and alarm windows. The operation of these is basically no different than the operation

of conventional keys. You operate these objects by touching them with the finger.

Caution

Always touch only one object on the screen. Do not touch several touch objects

simultaneously. You may trigger an unintended action.

Caution

Do not use any pointed or sharp objects when operating the touch screen in order to avoid

damaging the plastic surface.

Direct keys

With a PROFIBUS DP connection, it is also possible to configure buttons for operation as

direct keys in order to allow rapid operator inputs using keys. Rapid button operation is

conditional for jog mode, for example.

PROFIBUS-DP direct keys place bits directly from the HMI device in the I/O area of a

SIMATIC S7.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-3

Note

Direct keys can only be triggered by touch and not by a mouse click from an connected

external USB mouse.

Note

With touch operation, direct keys are triggered independent of any configured password

protection.

Notice

Direct keys are still active when the HMI device is in the "offline" mode.

Button action feedback

The HMI device outputs an acoustic and optical signal as soon as it detects the operation of

a touch object. This feedback is always output, irrespective of communication with the PLC.

Therefore, this feedback does not indicate whether the relevant action is actually executed or

not.

Acoustic acknowledgement

The HMI device outputs a beep to signal operation of a touch object. You can disable this

beep.

Visual feedback

The type of visual feedback depends on the operated touch object:

• Buttons

The HMI outputs different indications of the "Touched" and "Not touched" states, provided

the programmer has configured a 3D effect:

UntouchedTouched

The programmer defines the layout of a selected field (line width and color of the focus.)

• Hidden buttons

The focus of hidden buttons is not set after marking (focus width value is 0, default.) In

Runtime, the outline of a touched button is indicated as a line when you modify the focus

with value in the configuration data. This outline remains visible until the focus is set on

another operating object.

• I/O fields

After you touch an I/O field, a screen keyboard appears as a feedback signal.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Operating screen objects with buttons

Screen objects with predefined buttons can also be operated with external buttons. The

requires the programmer to have linked the relevant system functions to these buttons.

In WinCC flexible, these system functions are organized in the "Keyboard actions for screen

objects" group.

See also

Volume & Sounds (Page 6-17)

9.1.2.2 Input of values

Screen keyboard

The HMI device automatically opens the screen keyboard when you touch an input object

such as an I/O field. This screen keyboard also appears for the input of passwords for

access to protected functions. The HMI automatically hides the keyboard again when input is

complete.

Based on the configuration of the input object, the HMI device shows a screen keyboard only

for the input of numeric or alphanumeric values.

The screen keyboard is activated by selecting an input object in runtime.

See also

Open Control Panel (Page 6-2)

Operation with external keyboard/mouse (Page 5-9)

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-5

9.1.2.3 Input of numeric values

Numeric screen keyboard

The HMI device automatically opens the numeric screen keyboard for the input of numeric

values when you touch an I/O field on the screen. The HMI automatically hides the keyboard

again when input is complete.

The <Help> button is only active if an operator note is configured for the I/O field.

Figure 9-1 Screen keyboard for numeric input

Procedure

You enter the characters of numeric values using the screen keyboard buttons. Confirm the

input value with <Enter>, or cancel it with <Esc>. Both functions will close the screen

keyboard.

Note

The numeric input fields may be assigned limits. In this case, the system accepts only the

values which lie within the configured range. The system rejects any values which are out of

these limits and restores the original value. In this case, the HMI outputs a system alarm.

When you input of the first character a Quickinfo appears, showing the high and low limit

values of the input field.

See also

Input of values (Page 9-4)

9.1.2.4 Input of alphanumeric values

Alphanumeric screen keyboard

The HMI automatically opens an alphanumeric keyboard for the input of strings and numeric

values in hex format when you touch an input object on the screen. The HMI automatically

hides the keyboard again when input is complete.

The <Help> is only active if an operator note is programmed for the input object.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Figure 9-2 Screen keyboard for alphanumeric input

Keyboard layers

The alphanumeric keyboard is organized in several layers:

• Standard layer (see the figure)

• <Shift> layer

• <Alt Gr> layer

• <Shift+Alt Gr> layer

The <Alt Gr> and <Shift+Alt Gr> layers are used for the input of special characters.

Procedure

You use the screen keyboard buttons to input the characters of alphanumeric values.

Confirm the input value with <Enter>, or cancel it with <Esc>. Both functions will close the

screen keyboard.

9.1.2.5 Calling the operator note

Purpose

The operator notes provide additional information and operating instructions with respect to

alarms, screen and operable screen objects to the programmer. A operator note may contain

information about the permissible range of values for an I/O field, or information on the

causes of alarm events and their elimination.

Figure 9-3 Operator note for an I/O field (Example)

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-7

Help on messages

Actuate the button on the alarm screen or in the alarm view

Help on input objects

Touch the <Help> button on the screen keyboard. This button is only available if you

configured an operator note.

Help on the current screen

Call the operator note for the current screen

Help on the focused screen object

Use the <Alt+H> key combination on the screen keyboard or on the connected USB

keyboard to display the operator notes configured for the focused screen object.

Note

To view a new operator note, you first need to close the window showing the current

operator note.

9.1.3 Operating a keyboard device

9.1.3.1 Functions of the system keys

Overview of system key functions

Note

The availability of system keys is is determined by the HMI device used.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Key Function Purpose

A-Z

Toggling (numbers / letters) Toggles the assignment from numbers to letters.

• No LED is lit:

The number assignment is enabled. One actuation of the

button toggles to letter assignment.

• One LED is lit:

The left or right letter assignment is enabled.

Each time the key is pressed, the system toggles between the

right letter assignment and number assignment.

INS

DEL

Deleting characters • Deletes the character at the current cursor position.

ESC

Cancel • Deletes the input characters of a value and restores the

original value.

• Closes the active window.

ACK

Acknowledge Acknowledges the currently displayed alarm message, or all

messages of an acknowledgement group (group

acknowledgement.)

The LED is lit as long as unacknowledged alarm messages

are queued.

HELP

Viewing the operator note Opens the configured operator note for the selected object

(e.g. a message, I/O field.) The LED signals an that an

operator note exists for the selected object.

ENTER

Enter • Applies and closes the input

• Opens a drop-down list for symbolic I/O fields

• Triggers buttons

TAB

Tabulator Selects the next available screen object in the configured tab

sequence.

Deleting characters Deletes the character to the left of the current cursor position.

Moving the cursor • Selects the next operable screen object on the right or left,

above or below of the current screen object.

• Navigates in the screen object.

HOME

Scrolling back Scrolls one page down

END

Scrolling up Scrolls one page up.

SHIFT

Shift

(upper/lower case)

Use in key combinations, e.g. for switching to uppercase

letters.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-9

Key Function Purpose

Shift (special character) Use in key combinations for the input of special characters.

Some of the keys contain a blue special character on their

bottom left corner, e.g. the "%" character. In order to input

these characters, press the relevant key in combination with

the special character key shown on the left.

CTRL

General control functions Used in key combinations for navigating through trend views,

for example.

ALT

General control functions Used in key combinations, for example, for the "Status force"

screen object.

9.1.3.2 Functions of the key combinations

General operation

Navigation

Shortcut keys Function

SHIFT + TAB

Selects the previous available screen object in the

configured tab sequence.

SHIFT +

Positions the cursor within a screen object, for example, in

an I/O field.

FN + HOME

Jumps to the start of the selection list.

FN + END

Jumps to the end of a selection list.

SHIFT + FN + HOME

Selects a group of entries between the current position and

the top of the list, for example.

SHIFT + FN + END

Selects a group of entries between the current position and

the end of the list, for example.

ALT +

Opens a selection list.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Monitor screen settings

Shortcut keys Function

A-Z +

Increases the brightness of the monitor screen.

A-Z +

Reduces the brightness of the monitor screen.

In the startup phase

Shortcut keys Function

ESC

Toggles the HMI to "transfer" mode.

You can always exit transfer mode, provided the unit is

currently not transferring any data.

Further functions (e.g. in the Explorer)

Shortcut keys Function

CTRL + ENTER

Accepts the selected entry without closing the list.

CTRL + TAB

• Toggles the active window.

• Toggles between the base area and the window.

CTRL +

Selects all (left letter assignment is active.)

ALT +

ENTER

Shows the properties of a selected element.

Navigating in the operating system

General

Shortcut keys Function

CTRL + ESC

Opens the Windows CE Start menu.

ALT + TAB

Opens the task manager.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-11

Explorer

Shortcut keys Function

Changes to the parent level.

TAB

Toggles the display range.

ALT

Activates the menubar.

Dialogs

Shortcut keys Function

TAB

Jumps to the next field.

SHIFT + TAB

Jumps to the previous field.

Opens the next tab, if the focus is set on the name of this

tab.

Opens the previous tab, if the focus is set on the name of

this tab.

ESC

Closes the dialog without saving.

Operating screen objects with function keys

You may also operate screen objects with buttons, e.g. the alarm view, trend view, recipe

view or status force using function keys. The condition is here, that the programmer has

linked the corresponding system functions to the function keys.

In WinCC flexible, these functions are organized in the "Keyboard actions for screen objects"

group.

9.1.3.3 Calling the operator note

Purpose

The operator notes provide additional information and operating instructions with respect to

alarms, screen and operable screen objects to the programmer. An operator note may

contain information about the permissible range of values for an I/O field (refer to figure

below) or, in the case of an alarm, information on the causes of an alarm event and its

elimination.

Operating a project

9.1 Basic principles of operation

MP 370 (WinCC flexible)

9-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Figure 9-4 Operator note for an I/O field (Example)

Procedure

To call the operator note configured for an I/O field, for example:

1. Select the I/O field, e.g. .

The I/O field is selected. The LED signal of the HELP key indicates that an operator note is

available.

2. Press HELP to call the operator note.

The operator note is shown in the language currently set on the HMI. Any operator note

configured for the current screen is shown when you press the key again.

3. Close the Help window with the ESC key or by pressing the HELP key again.

Note

To view a new operator note, you first need to close the window showing the current

operator note.

See also

Set language (Page 7-12)

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-13

9.2 Controlling graphic objects

9.2.1 Button

9.2.1.1 Description

Purpose

A button is a virtual key on the screen of the HMI device that can have one or more

functions.

You can initiate separate, independent functions with the following button operations:

• Click

• Press

• Release

• Activate the button in the tab sequence

• Deactivate the button in the tab sequence

• Change

Layout

A button can be labeled, use a graphic symbol or be hidden.

The operation may be followed with a visual feedback. However, note that the optical

feedback only indicates a completed operation and not whether the configured functions

were actually executed.

9.2.1.2 Touch control

Procedure

Touch the button on the touch screen of the HMI device.

9.2.1.3 Keyboard control

Procedure

To operate a button with a keyboard:

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

• Use the cursor to select the button, e.g.

• Then press ENTER or .

9.2.1.4 Mouse and keyboard control

Procedure

Mouse

Click on the button with the mouse pointer.

Keyboard

Select the button with <Tab> according to the configured tab sequence, then press <Return>

or <Space>.

9.2.2 Switch

9.2.2.1 Description

Purpose

The switch is an control object and display object with two states: "pressed" and "released."

Switches can signal the state of a system component that cannot be seen from the HMI

device, e.g. a motor. You can also change the status of that system components at the HMI

device.

A switch has two stable states: When you actuate the switch, it changes to the other state.

The switch retains this status until the next operation.

Layout

A switch can be labeled with a descriptive name, e.g. "Motor 2" and/or the names of its two

states, e.g. "ON" and "OFF". The switch can be positioned vertically or horizontally.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-15

9.2.2.2 Touch control

Procedure

Touch operation of a switch differs depending on the switch type:

• If a slider is displayed for the switch:

Move the slider on the touch screen of the HMI device to the new position, or double-click

the slider area.

• If only a text or a graphic is displayed for the switch:

Touch the switch on the touch screen of the HMI device.

9.2.2.3 Keyboard control

Procedure

To operate a switch with a keyboard:

• Select the switch with a cursor key, e.g.

• Then press ENTER or .

9.2.2.4 Mouse and keyboard control

Procedure

Mouse

The operation depends on the type of switch:

• "Switch with text", "Switch with graphic": Click the switch

• Switch with slider: Click on the slider and move the slider to the other position.

Keyboard

Select the switch with <Tab> according to the configured tab sequence, then press <Return>

or <Space>

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.3 I/O field

9.2.3.1 Description

Purpose

You enter numeric or alphanumeric values in an I/O field. An example of a numerical value is

the number 80 as setpoint for a temperature. An alphanumeric value is the text "Service" as

user name.

Layout

The layout of an I/O field depends on its configuration in WinCC flexible, e.g.:

• Numeric I/O field

For input of numbers in decimal, hexadecimal or binary format.

• Alphanumeric I/O field

For input of character chains

• I/O field for date and time

For input of calendar dates or time information. The format depends on the language set

on the HMI device.

• I/O field for password input

For concealed input of a password. The input character string is displayed with

placeholders (*).

Behavior

If limit values are configured for the tag that is linked to the I/O field, the input value is only

applied if the value is within the configured limits.

Any input values which are out of range are rejected. The original value is displayed on the

I/O field instead, and a system alarm is output on the HMI device.

9.2.3.2 Touch control

Procedure

Press the I/O field on the touch screen of the HMI device. The screen keyboard

automatically appears. Enter the desired value using the screen keyboard. Confirm your

input with <Enter> or cancel it with <Esc>. After the input has been confirmed or canceled,

the screen keyboard is automatically closed.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-17

9.2.3.3 Keyboard control

Procedure

Enable the I/O field, for example with one or several TAB according to the configured tab

sequence. The selection is signaled by the colored field content.

You now have two options:

• Position the cursor with SHIFT and a cursor key. The selection of the field content is

cancelled. Type in the relevant value.

• Press ENTER . The object changes to the specific editing mode. Now, only one character will

be marked in the field.

– You can use the / cursor keys to scroll the character table.

– The / cursor keys can be used to move to the next or previous input

position.

Confirm your entry with ENTER or cancel it with ESC .

Note

To enter the hexadecimal characters "A" to "F" for numerical values, toggle the input keys

using A-Z to activate the letter assignment.

9.2.3.4 Operation with mouse and keyboard

Procedure

Mouse

Click in the I/O field with the mouse pointer. Type in the relevant value. Confirm your input on

the HMI with <Return> or cancel it with <Esc>.

Keyboard

Select the I/O field with <Tab> according to the configured tab sequence, for example. The

contents of the I/O field change color to show that it is now activated. You now have two

options:

• Type in the relevant value.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-18 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

• Press <Return>. The object changes to the specific editing mode. Now, only one

character will be marked in the field.

– Use the <Up>/<Down> cursor keys to scroll through a character table.

– Use the <Right>/<Left> cursor keys to move the cursor to the next or previous input

position.

Confirm your input on the HMI with <Return> or cancel it with <Esc>.

9.2.4 Graphic I/O field

9.2.4.1 Description

Purpose

In a graphic I/O field, select a predefined image from a selection list. The graphic represents

the value of a tag. This can be an internal tag or a tag with a connection to a PLC.

The graphic I/O field can also be used merely to output a pure graphic depending on the

value of a tag. In this case, you cannot then operate the graphic I/O field.

Layout

If the graphic I/O field shows a cactus icon, you have not defined the graphic output of a

specific value in your project.

9.2.4.2 Touch control

Procedure

Touch the graphic I/O field on the touch screen of the HMI device. Selection mode is

activated.

Select the desired graphic using the scroll bar.

Apply the required graphic by touching it, or reject the selection by touching another screen

object.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-19

9.2.4.3 Keyboard control

Procedure

Operating a graphic I/O field on a keyboard device:

Step Procedure

1 Select the graphic I/O field

e.g.

The graphic I/O field is marked.

2 Activate selection mode ENTER The selection mode is activated.

3 Select the entry

Moves the cursor by lines.

Accept the selection

ENTER

The selected entry is now valid.

The selection mode is closed.

Cancel the selection ESC

The function restores the original

value.

9.2.4.4 Mouse and keyboard control

Procedure

Mouse

Click on the graphic I/O field with the mouse pointer. The predefined images are displayed in

the selection list.

If the selection list has a scroll bar: Click on the scroll bar with the mouse pointer. Move the

scroll bar in the desired direction while holding down the mouse button.

Select the image and apply the corresponding tag value by clicking the entry. The selection

list is closed and the entry is displayed. The graphic I/O field remains active.

Keyboard

Select the graphic I/O field with <Tab> according to the configured tab sequence, for

example. The contents of the graphic I/O field change color to show that it is now activated.

You can control the graphic I/O field with the following keys:

Key Function

<Return> Opens the selection list

Confirms input. The selection list is closed. The graphic I/O field continues

to have the focus.

<Down> or <Right> Selects the next entry

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-20 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Key Function

<Up> or <Left> Selects the previous entry

<Esc> or <Tab> Discards the entry and displays the original value in the form of the

corresponding graphic.

9.2.5 Symbolic I/O field

9.2.5.1 Description

Purpose

In a symbolic I/O field select a predefined entry from a selection list. The entry represents the

value of a tag. This can be an internal tag or a tag with a connection to a PLC.

The symbolic I/O field can also be used to merely output an entry depending on the value of

a tag. In this case, the symbolic I/O field can no longer be operated.

The display options of the symbolic I/O fields depend on the WinCC flexible edition.

Layout

If the symbolic I/O field contains a blank text line in the drop-down list, you have not defined

a relevant entry in the project.

9.2.5.2 Touch control

Procedure

Touch the symbolic I/O field on the touch screen of the HMI device. The predefined entries

are displayed in the selection list.

If the selection list has a scroll bar: Touch the scroll bar on the touch screen of the HMI

device. Touch the touch screen continuously to move the scroll bar in the desired direction.

Select the desired entry and apply the associated tag value by touching the entry on the

touch screen. The selection list is closed and the entry is displayed. The symbolic I/O field

continues to have the focus.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-21

9.2.5.3 Keyboard control

Procedure

To operate a symbolic I/O field with a keyboard:

Step Procedure

1 Select the symbolic I/O field

e.g.

The symbolic I/O field is marked.

2 Opens the selection list ENTER The drop-down list opens.

3 Select the entry

Moves the cursor by lines.

Accept the selection

ENTER

The selected entry is now valid.

The drop-down list is closed.

Cancel the selection ESC

The function restores the original

value. The drop-down list is

closed.

9.2.5.4 Mouse and keyboard control

Procedure

Mouse

Click on the symbolic I/O field with the mouse pointer. The predefined entries are displayed

in the selection list.

If the selection list has a scroll bar: Click on the scroll bar with the mouse pointer. Move the

scroll bar in the desired direction while holding down the mouse button.

Select the entry, then apply the corresponding tag value by clicking the entry. The selection

list is closed and the entry is displayed. The symbolic I/O field continues to have the focus.

Keyboard

Activate the symbolic I/O field by pressing the <Tab> key one or more times, corresponding

to the configured tab order. The contents of the symbolic I/O field change color to show that

it is now activated.

You can control the symbolic I/O field with the following keys:

Key Function

<Enter> Opens the selection list

Confirms input. The selection list is closed. The symbolic I/O field continues

to have the focus.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-22 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Key Function

<Down> or <Right> Selects the next entry

<Up> or <Left> Selects the previous entry

<Esc> or <Tab> Discards the entry and displays the original value in the form of the

corresponding graphic.

9.2.6 Alarm indicator

9.2.6.1 Description

Purpose

The alarm indicator is a configurable graphic icon that is displayed on the screen as long as

at least one alarm belonging to the specified alarm classes is pending on the HMI device.

Behavior

The alarm indicator flashes as long as unacknowledged alarms are pending. The displayed

number indicates the number of pending alarms.

Note

The icons from the symbol library can only be operated with a mouse or touch screen.

9.2.6.2 Touch control

Procedure

Touch the alarm indicator. An alarm window opens depending on the configuration.

Use the Close icon to close the Alarm window and be able to operate the screens. The alarm

window can be opened again by touching the alarm indicator.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-23

9.2.6.3 Mouse control

Procedure

Click on the alarm indicator with the mouse pointer. An alarm window opens depending on

the configuration.

Use the Close icon to close the Alarm window and be able to operate the screens. The alarm

window can be opened again by clicking on the alarm indicator.

9.2.7 Alarm view

9.2.7.1 Description

Purpose

The Alarm view shows alarms or alarm events selected by the planner from the alarm buffer

or, if supported by the HMI device, from the alarm log.

Layout

To be able to distinguish between different alarms classes, they are identified in the first

column of the Alarm view:

Icon Alarm class

! Error

(empty) Operation

(depending on configuration) Custom alarm classes

$ System

In Runtime you can configure the column order and the sorting order of each column.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-24 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Operator controls

The buttons have the following functions:

Button Function

Use this button to call the configured operator note for the selected alarm.

This button triggers the function assigned to the "Edit" event for the selected

alarm.

This button is used to acknowledge an unacknowledged alarm.

9.2.7.2 Touch control

Procedure

Touch the desired operating element in the Alarm view on the touch screen of the HMI

device.

Changing column sequence and sorting sequence

In Runtime you can configure the column order and the sorting order of each column.

• Change column sequence

To reverse the "Time" and "Date" columns, for example, touch the "Date" header on the

HMI device touchscreen. Continue to press the touchscreen and drag the column

heading to the "Time" heading.

• Change sorting order

To change the chronological order of the alarms, touch the column heading, "Time" or

"Date" on the HMI device's touchscreen.

9.2.7.3 Keyboard control

Procedure

There is also a tab order in the alarm view for the list showing displayed alarms and all

configured buttons.

Proceed as follows to acknowledge an alarm using the keys.

1. Activate the alarm view using TAB , according to the tab order.

2. Select the alarm to be acknowledged. The HOME , END , and keys can be used

for this.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-25

3. Press and hold the TAB key until the button to be acknowledged is selected.

4. Press the ENTER key.

9.2.7.4 Mouse and keyboard control

Procedure

Mouse

Click on the desired control object or list entry.

Changing column sequence and sorting sequence

In Runtime you can configure the column order and the sorting order of each column.

• Change column sequence

For example, to reverse the "Time" and "Date" columns, drag the "Date" header to the

"Time" header with the mouse.

• Change sorting order

To change the chronological sorting order of the alarms, click on the header of one of the

two "Time" or "Date" columns.

Keyboard

There is also a tab sequence also for the list with displayed alarms and all configured

buttons within the alarm display.

For example, do the following to acknowledge an alarm using the keyboard.

1. Activate the screen display, for example with <Tab> according to the tab sequence.

2. Select the alarm to be acknowledged. You can use the keys <Home>, <End>, <Page

Up>, <Page Down>, <Up> and <Down> for this.

3. Hold the <Tab> key pressed until the button to be acknowledged is selected.

4. Press the <Return> button.

9.2.8 Simple alarm view

9.2.8.1 Description

Purpose

On an HMI device with a small display, the simple alarm view is used to display and edit

alarms.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-26 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Layout

The display of the simple alarm view depends on the configuration.

• The display shows all current, departed or acknowledged alarms of the selected alarm

classes.

• The number of lines per alarm and number of visible lines are specified in the

configuration.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-27

Operator controls

The buttons have the following functions:

Button Function

This button is used to acknowledge an unacknowledged alarm.

This button triggers the function assigned to the "Edit" event for the selected alarm.

Use this button to call the configured operator note for the selected alarm.

Use this button to browse upwards alarm by alarm.

Use this button to browse upwards through the alarm display page by page.

Use this button to browse downwards through the alarm display page by page.

Use this button to browse downwards alarm by alarm.

9.2.8.2 Touch control

Procedure

Touch the desired control object in the alarm view on the touch screen of the HMI device.

9.2.8.3 Keyboard control

Procedure

The simple alarm view also has a tab order for the list showing displayed alarms and all

configured buttons.

Proceed as follows to acknowledge an alarm using the keys.

1. Activate the simple alarm view using TAB , according to the tab order.

2. Select the alarm to be acknowledged. The HOME , END , and keys can be used

for this.

3. Press and hold the TAB key until the button to be acknowledged is selected.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-28 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4. Press the ENTER key.

9.2.8.4 Mouse and keyboard control

Procedure

Mouse

Click the relevant button.

Keyboard

There is also a tab sequence also for the list with displayed alarms and all configured

buttons within the alarm display.

For example, do the following to acknowledge an alarm using the keyboard.

1. Activate the screen display, for example with <Tab> according to the tab sequence.

2. Select the alarm to be acknowledged. You can use the keys <Home>, <End>, <Page

Up>, <Page Down>, <Up> and <Down> for this.

3. Hold the <Tab> key pressed until the button to be acknowledged is selected.

4. Press the <Return> button.

9.2.9 Recipe view

9.2.9.1 Description

Purpose

The recipe view is a screen object that is used in runtime to display and edit recipe records.

Layout

The functions of the recipe view can be configured. To use the Recipe view on small panels,

a simple view is also available, for example.

Different settings are also possible for whether the recipes available in the recipe view can

only be selected or can also be changed.

Behavior

If you change to another screen and have not yet saved changes to the recipe data in the

recipe view, you will be prompted to save the recipe data. The recipe name and the name of

the recipe record are displayed to show which recipe data have not been saved yet.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-29

When you change to a screen that contains a recipe view loaded with recipe data, the recipe

data is automatically updated.

Operator controls

The following operator controls can be configured in the recipe view:

Operator control

element

Function

Displays the configured operator notes of the given recipe view.

Creates a new recipe record in the recipe that is displayed in the specified recipe view. The recipe

record values are preset with the values that were specified as "Default value" when the recipe was

configured.

Saves the recipe data record which is currently displayed in the recipe view. The storage location is

determined during configuration in the properties view for the recipe.

Saves the recipe record currently being displayed in the recipe view under a new name. The storage

location is determined during configuration in the properties view for the recipe.

Deletes the recipe record that is displayed in the recipe view from the data medium of the HMI device.

Synchronizes the values of the recipe record that is currently displayed in the recipe view with the

associated tags.

During synchronization, all values of the recipe record are written to the associated tags. Then the

values are read from the tags and used to update the values in the recipe view.

Transfers the recipe record, which is currently displayed in the recipe view, to the connected PLC.

Transfers the recipe record, which is currently loaded in the PLC, to the HMI device and displays it in

the recipe view.

9.2.9.2 Touch control

Procedure

Touch the desired operating element in the Recipe view on the touchscreen of the HMI

device.

Use the screen keyboard to enter values.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-30 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.9.3 Keyboard control

Procedure

Activate the recipe view using TAB , according to the configured Tab order.

The table below shows the shortcut keys used to control the recipe view:

Shortcut keys Function

CTRL +

Creates a new recipe record in the recipe that is displayed in the

specified recipe view. The recipe record values are preset with the

values that were specified as "Default value" when the recipe was

configured.

CTRL + ENTER

Saves the recipe data record which is currently displayed in the recipe

view. The storage location is determined during configuration in the

properties view for the recipe.

CTRL + *

Saves the recipe record currently being displayed in the recipe view

under a new name. The storage location is determined during

configuration in the properties view for the recipe.

CTRL +

INS

DEL

Deletes the recipe record that is displayed in the recipe view from the

data medium of the HMI device.

CTRL + =

Synchronizes the values of the recipe record that is currently displayed

in the recipe view with the associated tags.

During synchronization, all values of the recipe record are written to the

associated tags. Then the values are read from the tags and used to

update the values in the recipe view.

CTRL +

Transfers the recipe record, which is currently displayed in the recipe

view, to the connected PLC.

CTRL +

Transfers the recipe record, which is currently loaded in the PLC, to the

HMI device and displays it in the recipe view.

9.2.9.4 Mouse and keyboard control

Procedure

Mouse

Click the desired control object or list entry.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-31

Keyboard

Activate the recipe view, for example with <Tab> according to the tab sequence.

The table below shows the shortcut keys used to control the recipe view:

Shortcut keys Function

<Ctrl+Space> Creates a new recipe record in the recipe that is displayed in the specified

recipe view. The recipe record values are preset with the values that were

specified as "Basic value" when the recipe was configured.

<Ctrl+Return> Saves the recipe data record which is currently displayed in the recipe view.

The storage location is determined during configuration in the properties

view for the recipe.

<Ctrl+*> Saves the recipe record currently being displayed in the recipe view under a

new name. The storage location is determined during configuration in the

properties view for the recipe.

<Ctrl+Del> Deletes the recipe record that is displayed in the recipe view from the data

medium of the HMI device.

<Ctrl+=> Synchronizes the values of the recipe record that is currently displayed in

the recipe view with the associated tags.

During synchronization, all values of the recipe record are written to the

associated tags. Then the values are read from the tags and used to update

the values in the recipe view.

<Ctrl+Down> Transfers the recipe record, which is currently displayed in the recipe view,

to the connected PLC.

<Ctrl+Up> Transfers the recipe record, which is currently loaded in the PLC, to the HMI

device and displays it in the recipe view.

9.2.10 Simple recipe view

9.2.10.1 Description

Purpose

On an HMI device with a small display, the simple recipe view is used to display and edit

recipes.

Layout

The simple recipe view consists of three areas:

• Recipe selection

• Recipe data record selection

• Recipe entries

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-32 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

In the simple recipe view, each area is shown separately on the HMI device. The simple

recipe view always begins with the recipe selection.

Behavior

A command option selection can be called in for each display area by pressing the

button. The command selection lists those commands that are available in the current

display area. Each command is assigned a number which you can use to select it directly

from the list (without using the <Enter> key).

Operator controls

The buttons have the following functions:

Button Function

Returns to the previous selection

Calls up the shortcut menu commands.

9.2.10.2 Touch control

Procedure

Touch the desired control object or list entry in the simple recipe view on the touch screen of

the HMI device.

9.2.10.3 Keyboard control

Procedure

Each command for processing recipes and recipe records is assigned a number that is

shown in the command selection. You can select the command directly by pressing the

corresponding number key on the HMI device.

The following table lists the key combinations for controlling the simple recipe view:

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-33

Shortcut keys Function

Calls the shortcut menu commands.

Selects the previous/next entry

HOME

END

Scrolls one page up or down and selects the corresponding entry

SHIFT + HOME

SHIFT + END

Selects the first/last entry

ESC

Returns to the previous selection

ENTER

Displays the recipe data records or recipe elements according to the

selection

9.2.10.4 Mouse and keyboard control

Procedure

Mouse

Click the desired control object or list entry.

Keyboard

Each command for processing recipes and recipe records is assigned a number that is

shown in the command selection. You can select the command directly by pressing the

corresponding number key on the HMI device.

The following table lists the key combinations for controlling the simple recipe view:

Key Function

<Right> Calls the shortcut menu commands.

<Up>/<Down>: Selects the previous/next entry

<Pg Up>/<Pg Down> Scrolls one page up or down and selects the corresponding entry

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-34 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Key Function

<Home>/<End> Selects the first/last entry

<Esc> Returns to the previous selection

<Enter> Displays the recipe data records or recipe elements according to the

selection

9.2.11 Bar

Purpose

The bar is a dynamic display object. The bar displays a value from the PLC as a rectangular

area. The operator at the HMI device can thus see immediately how far the current value is

from the configured limit value or whether a setpoint value has been reached. The bar can

display values such as fill levels or batch counts.

Layout

The layout of the bar is set in the user program. In the bar, for example, lines can identify the

configured limit values. Color changes can signal when a limit value has been exceeded or

not been met.

Operation

The bar is for display only and cannot be controlled by the operator.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-35

9.2.12 Trend view

9.2.12.1 Description

Purpose

The trend view is a dynamic display object. The Trend view can display actual process data

and process data from a log continuously when it is supported by the HMI device.

Layout

The layout of the trend view is based on the configuration. A trend view can show multiple

curves simultaneously to allow the user, for example, to compare different process

sequences. If the displayed process value exceeds or falls below the configured limit values,

the violation of the limit can be displayed by a change of color in the curve.

A ruler can also simplify the reading of the process values from the trend view. The ruler

displays the Y-value that belongs to an X-value.

Operator controls

The trend view is operated by the configured trend display buttons. If no buttons have been

configured for the trend view, you can operate the trend view using the keyboard or the

function keys of the HMI device. Prerequisite is that the project engineer has configured and

documented this type of operation.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-36 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Operator control

element

Function

Scrolls back to the beginning of the trend recording. The start values of the trend recording are

displayed there.

Zooms the displayed time section

Zooms out of the displayed time section

Moves the ruler backward (to the left).

Moves the ruler forward (to the right).

Scrolls one display width backward (to the left).

Scrolls one display width forward (to the right).

Shows or hides the ruler. The ruler displays the X-value associated with a Y-value.

Stops or continues trend recording

9.2.12.2 Touch control

Procedure

Touch the desired control object in the trend view on the touch screen of the HMI device.

9.2.12.3 Keyboard control

Procedure

Activate the trend view with TAB using the tab order configured.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-37

The table below shows the available shortcut keys:

Keys Function

CTRL +

ENTER

Scrolls back to the beginning of the trend recording. The start values of

the trend recording are displayed there.

CTRL + +

Zooms the displayed time section.

CTRL + –

Zooms out of the displayed time section.

CTRL + ALT +

Moves the ruler backward (to the left).

CTRL + ALT +

Moves the ruler forward (to the right).

SHIFT +

Scrolls one display width backward (to the left).

SHIFT +

Scrolls one display width forward (to the right).

9.2.12.4 Mouse and keyboard control

Procedure

Mouse

Click the desired button.

Keyboard

Activate the trend view with <Tab>, using the tab order configured.

The table below shows the available shortcut keys:

Key Key (Panel PC) Function

<Ctrl+Return> <Ctrl+Return> Scrolls back to the beginning of the trend recording. The

start values of the trend recording are displayed there.

<Ctrl+Plus> <Ctrl+Plus> Zooms the displayed time section

<Ctrl+Minus> <Ctrl+Minus> Zooms out of the displayed time section

-- <Ctrl+Alt+Left> Moves the ruler backward (to the left).

-- <Ctrl+Alt+Right> Moves the ruler forward (to the right).

<Left> <Shift+Left> Scrolls one display width backward (to the left).

<Right> <Shift+Right> Scrolls one display width forward (to the right).

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-38 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.13 Slider control

9.2.13.1 Description

Purpose

The slider is used to transfer a numerical value to the PLC by moving the slide to the desired

position. Each change in the position of a slider element results in the immediate change of

the corresponding value at the associated tag.

Note

The displayed value on the slider control may deviate from the actual value in the following

circumstances:

• The value range (minimum and maximum value) configured for the slider control does not

correspond to the configured limits for the slider control tag.

• An invalid password has been entered for a password-protected slider control.

Layout

If the slider control is used as a display object, the value represented is determined by the

position and configuration of the movable slider.

9.2.13.2 Touch control

Procedure

Touch the slider on the touch screen of the HMI device. Move the slider in the desired

direction while keeping contact with the screen.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-39

9.2.13.3 Keyboard control

Procedure

One way to operate the slider control with a keyboard is to use the cursor keys

The following table lists the key combinations for controlling the slider control:

Keys Meaning

SHIFT +

Increase value

SHIFT +

Reduce value

HOME

END

Increase value in 5% increments

FN+ HOME

FN+ END

Move to maximum/minimum value

9.2.13.4 Mouse and keyboard control

Procedure

Mouse

Click the slider control. Move the slider control in the desired direction while holding down

the mouse button.

Keyboard

Activate the trend view with <Tab>, using the tab order configured.

You can operate the slider with the following keys:

Key Key (Panel PC) Function

<Up> or <Right> <Shift+Up> or <Shift+Right> Increase value

<Down> or <Left> <Shift+Down> or <Shift+Left> Reduce value

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-40 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Key Key (Panel PC) Function

<Page up> -- Increase value in 5% increments

<Page down> -- Reduce value in 5% increments

<Home> -- Set maximum value

<End> -- Set minimum value

9.2.14 Gauge

Purpose

The gauge is a dynamic display object. The gauge displays numeric values in analog form

by means of a pointer. The operator at the HMI device can thus see at a glance, for

example, that the boiler pressure is in the normal range.

Layout

The layout of the gauge depends on the configuration. Up to three differently colored areas

can be set up on the scale to visualize different operating states, such as normal operation,

warning range and danger range.

A trailing pointer can display the maximum value reached so far on the scale. The trailing

pointer is reset when the screen is reloaded.

The label on the scale can show the measured variable, e.g. boiler pressure, and the

physical unit, e.g. bar.

Operation

The gauge is for display only and cannot be controlled by the operator.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-41

9.2.15 Date / time field

9.2.15.1 Description

Purpose

The date / time field indicates the system time and data. In Runtime, you may change the

system time and data in accordance with the configuration.

Layout

The layout in the date/time field depends on the language set in the HMI device.

Behavior

An input values other than the date and system time are rejected. Instead, the original values

(plus the time that has elapsed in the meantime) will appear in the date/time field and a

system alarm will be displayed on the HMI device.

9.2.15.2 Touch control

Procedure

Touch the date/time field on the touch screen of the HMI device. The screen keyboard

automatically appears. Enter the desired value using the screen keyboard. Confirm your

input with <Enter> or cancel it with <Esc>. After the input has been confirmed or canceled,

the screen keyboard is automatically closed.

9.2.15.3 Keyboard control

Procedure

Enable the date / time field with one or several TAB , according to the configured tab

sequence. The selection is signaled by the colored field content.

You now have two options:

• Use the cursor keys to position the cursor and then enter your value.

• Press ENTER . The object changes to the specific editing mode. Now, only one character will

be marked in the field.

– You can use the / cursor keys to scroll the character table.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-42 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

– The / cursor keys can be used to move to the next or previous input

position.

Confirm your entry with ENTER or cancel it with ESC .

9.2.15.4 Mouse and keyboard control

Procedure

Mouse

Click in the date/time field. Type in the relevant value. Confirm your input on the HMI with

<Return> or cancel it with <Esc>.

Keyboard

Select the date / time field using the <Tab> key according to the configured tab sequence,

for example. The contents of the I/O field will change color to show that it is now activated.

You now have two options:

• Type in the relevant value.

• Press <Return>. The object changes to the specific editing mode. Now, only one

character will be marked in the field.

– Use the <Up>/<Down> cursor keys to scroll through a character table.

– Use the <Right>/<Left> cursor keys to move the cursor to the next or previous input

position.

Confirm your input on the HMI with <Return> or cancel it with <Esc>.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-43

9.2.16 Clock

Purpose

The clock displays the system time of the HMI device.

Layout

The time is displayed in analog or digital form, depending on the configuration. The current

date is also displayed in the digital view. The display format depends on the language set on

the HMI device.

Operation

The clock is for display only and cannot be operated. You can use the Date/Time field, for

example, to set the date and time.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-44 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.17 User view

9.2.17.1 Description

Purpose

The user view is used by the administrator to manage user accounts, group assignments

and user passwords.

Users can change their passwords and logoff times.

Layout

The user view contains four columns for the user, password, group and log-off time. The

passwords are encrypted by means of asterisks.

• The users in the "Administrators" group can view all existing users in the user view,

change all entries and create new user accounts.

• Other users only see a single line in the user view showing their own user name.

If the name or password of a logged on user is entered, a system alarm is output.

Export and import

A user view contains all users, passwords, group assignments and logoff times set up on the

HMI device. To eliminate the necessity of reentering all data again on another HMI device,

you can export the user view, and then import it to another device. However, this is only

possible if this function has been configured.

Note

Do not export the password list immediately after changing it. Exit the "User view" object

after making changes and wait until the changes have been written to the internal Flash

memory before performing the export.

Notice

The currently valid passwords are overwritten during an import. The imported passwords are

valid immediately.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-45

9.2.17.2 Touch control

Procedure

To create a new user, touch an empty line. Then use the screen keyboard to type in the user

name and confirm your entry with <Enter>. Assign a password and a logoff time in the same

way and then select the group.

To change user data, touch the relevant field and make the change.

9.2.17.3 Keyboard control

Procedure

Select the user view, for example with TAB according to the configured tab sequence.

• To create a new user, select an empty line using the cursor keys and then press ENTER .

Enter the user name and press ENTER . Use to go to the next field and repeat the

procedure.

• To change the user data, select the desired line using the cursor keys and then press

ENTER .

Make the desired changes and then complete the action by pressing ENTER .

9.2.17.4 Mouse and keyboard control

Procedure

Mouse

To create a new user account, click an empty line. Type in the user name, then confirm your

entry with <Return>. Assign a password and a logoff time in the same way and then select

the group.

To change user data, click the relevant field and make the change.

Keyboard

Select the user view, for example, using the <Tab> key according to the configured tab

sequence.

To create a new user account, select an empty line using the cursor keys and then press

<Return>. Type in the user name, then confirm your entry with <Return>. Use <Right> to go

to the next field and repeat the procedure.

To change the user data, select the desired line using the cursor keys and then press

<Return>. Then make the relevant changes.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-46 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.18 Simple user view

9.2.18.1 Description

Purpose

On HMI devices with a small display, the simple user view is used to display users on the

HMI device.

Layout

Users in the "Administrators" group see all existing users in the user view.

Other users only see a single line in the user view showing their own user name.

9.2.18.2 Touch control

Procedure

Touch the relevant entry in the simple user view on the touch screen of the HMI device.

Use the screen keyboard to input data.

9.2.18.3 Keyboard control

Entering custom user data

Custom user data (name, password, group, log-off time) is entered sequentially in several

dialogs.

Procedure

Select the simple user view with TAB , using the tab order configured. Select one of the

users displayed using the cursor keys and press ENTER .

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-47

The following table shows the available key operations for entering custom user data in the

dialogs:

Key Function

Selects the previous/next user

TAB

Selects the next element in the dialog

ENTER

Opens the next dialog

9.2.18.4 Mouse and keyboard control

Entering custom user data

Custom user data (name, password, group, log-off time) is entered sequentially in several

dialogs.

Procedure

Mouse

Start the input mode by clicking on the desired user name.

Keyboard

Start the input mode by activating the simple user view, for example, using the <Tab>

sequence and then select the user with <Enter>.

The following table shows the available key operations for entering custom user data in the

dialogs:

Key Function

<Up>/<Down>: Selects the previous/next user

<Tab> Selects the next element in the dialog

<Enter> Opens the next dialog

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-48 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

9.2.19 Status force

9.2.19.1 Description

Purpose

You read or write access values of the connected PLC directly in the status / control view.

The status / control view allows you to carry out operations such as monitoring or modifying

the addresses of the PLC program, without the need of an online connection via PC or PG.

Note

The status force view can only be used in combination with SIMATIC S5 or SIMATIC S7

PLCs.

Layout

The screen shows the general layout of the status / control screen object. Every row

represents an address.

If your HMI device has a mouse or a touch screen, you can change the column sequence on

the HMI device. For example, to interchange the format and control value columns, drag the

control value header to the format header.

The table shows the meaning of the individual columns.

Column Function

Connection The PLC of which the address ranges are to be displayed

Type, DB number, offset, bit The address range of the operand

Data type, format The data type of the operand

Status value The value that was read from the given address of the operand

Control value The value to be written to the given address of the operand

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-49

Operator controls

The buttons have the following functions:

Button Function

This button refreshes the display in the status value column.

The button engages when it is pressed. You cannot operate any input fields

until the button is actuated again and the refresh is stopped.

Use this button to accept the new value in the control value column. The

control value is then written to the PLC.

9.2.19.2 Touch control

Procedure

To enter or edit values, touch the respective field. A screen keyboard or a selection list

appears.

Touch the relevant buttons to write or read the values.

9.2.19.3 Keyboard control

Procedure

The following table lists the key combinations for controlling the status force:

Keys Meaning

CTRL + ENTER

Operates the "Write" button

CTRL +

Operates the "Read" button.

CTRL +

Selects the first/last field in the current row.

CTRL +

Selects the first/last field in the current column.

CTRL + ALT +

Increases the width of the current column.

CTRL + ALT +

Decreases the width of the current column.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-50 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Keys Meaning

CTRL +

INS

DEL

Deletes the current row

Otherwise:

Select "Internal tag" in the "Link" column.

CTRL + +

Optimize column width.

ENTER

Opens selection field

9.2.19.4 Mouse and keyboard control

Procedure

Mouse

To enter or edit values, click the relevant field. Enter the value using the keyboard, or select

a value from the selection list.

Click the desired buttons to write or read the values.

Keyboard

The following keys can be used on the keyboard to operate Status Force.

Key Key (Panel PC) Function

<Ctrl+Return> <Ctrl+Enter> Operating the "Write" button

<Ctrl+Space> <Ctrl+Space> Operating the "Read" button

<Ctrl+Left> <Ctrl+Shift+Left> Selects first field in current row

<Ctrl+Right> <Ctrl+Shift+Right> Selects last field in current row

<Ctrl+Up> <Ctrl+Shift+Up> Selects first field in current column

<Ctrl+Down> <Ctrl+Shift+Down> Selects last field in current column

<Ctrl+Del> <Ctrl+INS/DEL> Deletes current row

<Return> <Enter> Opens selection list

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-51

9.2.20 Sm@rtClient view

9.2.20.1 Description

Purpose

The Sm@rtClient view may be used to start remote monitoring and control of another HMI

device.

With an appropriate configuration, the Sm@rtClient view can be used to monitor and control

a system process from multiple HMI devices with the same authorizations.

Layout

The Sm@rtClient view displays the current Runtime screen of the remote device on your

HMI device. You can now monitor and control this screens according to your configuration.

Scroll bars are displayed if the screen of the remote HMI device is larger than that of your

HMI device.

Behavior

Start

The call for starting remote monitoring or control can be configured in different ways.

Depending on the project, you can view the Runtime of the remote HMI device by taking the

following steps:

• Automatically when the device is started (and selection of the screen with the

Sm@rtClient view, if this is not the start screen)

• By activating the Sm@rtClient view with the <Tab> key or (on a touch screen device)

through a touch

• By entering the IP address of the remote HMI device and, if required, entering a

password in the appropriate field in the Sm@rtClient view

Note

If you enter an incorrect password five time in succession, all attempts to establish a

connection are rejected for the next ten seconds.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-52 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Stop

The screen showing the display of the remote HMI device can be configured to be closed in

different ways. Depending on the configuration, you can terminate the remote monitoring or

remote operation and open the next object of your own project by taking one of the following

steps:

• Press the appropriate key.

• Click "Exit".

• Exit the screen.

• Press <Shift+Ctrl> or (with touch devices) press a clear spot for an extended period. The

menu opens with the corresponding menu item.

Monitoring mode

On a Sm@rtClient view which is configured for monitoring mode, you can only monitor the

remote HMI device. You cannot control its operation.

In this case, the keys retain their standard functions. Press <Tab> to open the next object in

the current screen of your project according to the configured tab sequence.

Control mode

The Sm@rtClient view can be run in two different control modes:

• If the "shared" check box is not set in the "Display" area of the "General" property view,

only one HMI device can use the remote control function at any time. The others can be

used to monitor the activities. Depending on the setting, a further HMI device logon will

either be rejected, or the existing connection will be shut down so that the new HMI

device can connect.

• If the "shared" check box is set in the "Display" area in the property view "General", every

HMI device on which remote operation is activated can access the remote HMI device

and assume control of the process. Only one HMI device can be active at a time in this

case. A different HMI device can first assume control when there has been no activity on

the active HMI device for a specified period of time.

The appearance of the mouse pointer indicates when operator control is possible.

In both operation modes, the operator at the remote device is not permitted to initiate any

further actions.

Note

In the event of emergency, you can override the operation block on the remotely

controlled or currently inactive HMI device by clicking on the user interface five times in

succession or pressing the <Shift> key five times in succession. Then you may have to

enter a specific (configured) password.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-53

Keys

In operation mode, all keys have the same function as those on the remote HMI device. You

can therefore use the <Tab> key to move from one object to another on the remote screen,

in the order of the tab configuration.

Function keys

When you press a function key that has been configured with a function, this function will be

executed in your project.

If you press a function that has

not

been configured with a function in your project, it will

actuate the function key on the remote HMI device.

9.2.20.2 Touch control

Procedure

Touch the desired operating element on the touch screen of the HMI device.

9.2.20.3 Keyboard control

Procedure

How do I operate the Sm@rtClient view with touch?

• Activate the desired control object with TAB according to the configured tab sequence on

the remote HMI device.

• Move the scroll bars in the desired direction with CTRL + or CTRL + .

• To exit the Sm@rtClient view, display a menu line with SHIFT + CTRL . Use ALT to make a

selection and the correponding shortcut key for the desired menu command.

9.2.20.4 Mouse and keyboard control

Procedure

Mouse

Click on the desired control object with the mouse pointer.

To operate a scroll bar, click on it with the mouse pointer and move it in the desire direction

while holding down the mouse button.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-54 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Keyboard

• Activate the desired control object with <Tab> according to the configured tab sequence

on the remote HMI device

• You can move the scroll bars in the desired direction with <Ctrl+Up/Down>.

• To exit the Sm@rtClient view, display a menu line with <Shift+Ctrl>. Select the desired

menu command with <Alt+Shortcut key>.

9.2.21 Symbol library

9.2.21.1 Description

Purpose

The symbol library is a comprehensive library with images from the areas of technology and

production.

Behavior

The following events can trigger functions when the project engineer has configured this for

the symbols:

• Click

• Double-click

• Press

• Release

• Enable

• Disabling

Note

The icons from the symbol library can only be operated with a mouse or touch screen.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 9-55

9.2.21.2 Touch control

Procedure

Touch the symbol on the touch screen of your HMI device.

There is no operator feedback, for example with color changes.

9.2.21.3 Mouse control

Procedure

Click on the symbol with the mouse pointer. The active mouse function is signaled in

Runtime by a changing cursor icon according to your configuration.

There is no operator feedback, for example with color changes.

Operating a project

9.2 Controlling graphic objects

MP 370 (WinCC flexible)

9-56 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-1

Operating recipes 10

10.1 Recipes

Overview

Recipes are a collection of associated data, e.g. machine configuration or production data.

You can transfer these data, for example, from the HMI device to the controller in a single

step in order to change the production variant. If you have programmed directly at the

machine, for example, you can transfer the data to your HMI device and write these to the

recipe.

Operating recipes in Runtime

WinCC flexible offers two options of viewing and editing recipes and the corresponding

recipe data records in Runtime on the HMI device:

• Recipe view

• Recipe screen

Operating recipes

10.1 Recipes

MP 370 (WinCC flexible)

10-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Recipe view

The recipe view is a screen object that is configured in the "Screens" editor. For example,

you can specify what operating function the recipe view will have in Runtime:

The recipe view shows recipe data records in tabular form. The Recipe view is particularly

useful if data records are small in size or only a few values are to be modified.

Recipe screen

A recipe screen represents a process screen which you configured as individual input screen

form by means of an individual layout of I/O fields and other screen objects in the "Screens"

editor. This makes it possible for you to input parameter data in the context of machine

visualization. The I/O fields for a recipe can be distributed over multiple recipe screens, with

topical organization of recipe elements, for example. The operating functions for the recipe

screens must be configured explicitly in the process screens.

Operating recipes

10.2 Structure of recipes

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-3

10.2 Structure of recipes

Introduction

A product often has several variants. For example, product variants can differ with respect to

size or quality. This condition is accurately reflected in a recipe.

Principle

A recipe consists of recipe data records containing values. The structure of a recipe is

explained using the example of a filing cabinet.

Each recipe represents a drawer of the file cabinet shown, and thus precisely one product. If

the fruit juice mixing plant is producing orange, apple, and tropical fruit flavors, you would

then configure one recipe for each flavor.

You define the recipe elements in the recipe. A recipe element consists of the display name

and a tag. The display names are indicated in the recipe data records and on the HMI device

in the recipe view. In Runtime, the appropriate tag value is read from the controller or

transferred to the controller.

Operating recipes

10.3 Structure of recipe data records

MP 370 (WinCC flexible)

10-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

10.3 Structure of recipe data records

Introduction

A recipe data record corresponds to a file card in an individual drawer and thus to a single

product variant. If the fruit juice mixing plant is producing juice, nectar, and fruit drinks, you

would then create a recipe data record in the recipe for each product variant. In this case,

the product variants consist of the different mixing ratios for the ingrediants.

A recipe data record is a set of values for the tags defined in the recipe. You enter the values

in the input fields. You can enter the values either during configuration or during runtime on

the HMI device or the machine.

To produce a product, you transfer the appropriate recipe data record from the HMI device to

the connected controller. The values in the recipe data record cannot be changed on the

HMI device unless the configuring engineer has provided for this.

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-5

Editing recipe data records

You can edit recipe data records during configuration or in runtime on the HMI device.

• During configuration, you can define recipes in the "Recipes" editor in the "Elements" tab.

You can enter values in the recipe data records in the "Data records" tab.

• During runtime, you have the option of entering recipe data record values directly on the

HMI device or importing them via a CSV file. You can also export the recipe data records

to a CSV file.

10.4 Recipe application

10.4.1 Transfer of recipe data records

Introduction

Recipe data records can be transferred in Runtime between external data storage media,

e.g. a flash memory, an HMI device and a controller.

Principle

The figure below shows how recipe data records can be transferred. You configure the

appropriate functionality for transferring data records in the recipe view. In a recipe screen,

you use the system functions provided for this purpose.

The HMI device stores recipe data records on a storage medium such as a flash memory

device or hard disk. You can edit a recipe data record in a recipe view or recipe screen on

the HMI device display.

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

10-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

(1) Save: Values you change on the recipe view or recipe screen are written to the recipe

data record on the storage medium by executing the "Save" function.

(2) Load: The "Load" function is used to update the values of recipe tags shown on the

recipe screen with the values of the recipe data record of the storage medium. The function

overwrites any values changed on the recipe screen. The "Load" function is executed for the

Recipe view when the data record is selected again.

(3) Write to controller: The values deltas of the recipe view and recipe screen are

downloaded to the PLC by calling the "Write to controller" function.

(4) Read from controller: Call the "Read from controller" function to update the indicated

values of the recipe view and recipe screen with the controller values. The function

overwrites any data changed on the recipe view or screen.

(5) Synchronization with controller: In your configuration, you can decide to synchronize the

values in the recipe view with the values of the recipe tags by setting the "Synchronization

with controller" function. After this synchronization, both the recipe tags and the recipe view

contain the current updated values. When the "Variables offline" setting is disabled for the

recipe, the current values are also applied in the controller.

(6) Import, Export: A data record can be exported to an external data carrier in order to

process it in MS Excel, for example. The data record is there stored in *.csv format.

10.4.2 Configuration of recipes

Introduction

You configure recipes according to your intended application. To write a value to a recipe

data record on your HMI device without disturbing the current process, you need

configuration settings other than those required for assigning parameters to a machine.

Principle

In the configuration settings of a recipe, you specify the behavior of the tags you are using in

the recipe. The figure below shows the basic differences when working with recipe data

records.

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-7

These configuration settings are made under "Settings" in the property view:

Configuration 1: Recipe without "Synchronize tags"

Data of a data record that has been read are only displayed and can only be edited in the

recipe view. Using these same tags outside of the recipe view does not affect their values.

Configuration 2: Recipe with "Synchronize tags" and with "Tags offline"

The "Synchronize tags" option is used to specify that the data of a data record read from the

controller or storage medium are to be written to or read from the tags you have configured

for the recipe.

The "Offline" option ensures that the input data are written to the tags without being

transferred directly to the controller.

Configuration 3: Recipe with "Synchronize tags" and without "Tags offline"

The "Synchronize tags" option is used to specify that the data of a data record read from the

controller or storage medium are to be written to or read from the tags you have configured

for the recipe.

The input or read data are transferred immediately to the controller:

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

10-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Synchronization with the controller

In the case of synchronous transfer, both the controller and the HMI device set status bits in

the shared data compartment. You can use this mechanism to prevent uncontrolled

overwriting of data in either direction in your control program. You define the address range

of the data compartment separately for each controller on the "Range pointer" tab in the

"Connections" editor.

Applications for synchronous transfer of recipe data records:

• The controller is the "active partner" for the transfer of recipe data records.

• The controller evaluates the data containing the recipe number and name, as well as the

recipe data record number and name.

• Triggering the transfer of data records by means of system function or PLC job, e.g. with

the system functions "SetDataRecordToPLC" and "GetDataRecordFromPLC", or with the

PLC jobs "Set_Data_Record_To_PLC" and "Get_Data_Record_From_PLC."

In order to synchronize transfer of data records between the HMI device and the controller,

the following requirements must be met during configuration:

• The "Data mailbox" range pointer is located under "Range pointers" in the project view.

• The controller with which the HMI device synchronizes the data record transfer is

specified in the recipe properties.

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-9

10.4.3 Scenario: Entering recipe data records in Runtime

Objective

You want to enter production data on the HMI device without disturbing the process that is

currently underway. Therefore, the production data should not be transferred to the PLC.

Sequence

You enter the production data in the recipe view or the recipe screen, assign a recipe data

record name, and save the new recipe data record on the storage medium of the HMI

device.

Configuration in WinCC flexible

You configure the recipe along with the associated tags.

Synchronization with the recipe tags is not necessary, because production data (tags) are

not intended to be transferred to the PLC. Make the following settings for the recipe in the

property view:

Depending on the extent of the recipe, you either configure a recipe view or create a recipe

screen.

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

10-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

10.4.4 Scenario: Manual production sequence

Objective

The production data are to be requested by the PLC according to the work piece to be

processed and displayed on the HMI device for inspection. You want to be able to correct

the transferred production data online, if necessary.

Sequence

A reading device connected to the PLC reads a bar code on the work piece to be processed.

The recipe data record names correspond to the respective bar code names. This will enable

the PLC to load the necessary recipe data record from the storage medium of the HMI

device. The recipe data record is displayed for inspection. Changes are transferred

immediately to the PLC.

Configuration in WinCC flexible

You configure the recipe along with the associated tags.

Production data are to be transferred to the PLC, so it is necessary to synchronize with the

PLC to prevent the data from accidentally overwriting each other. The tags are to be

transferred to the PLC. Make the following settings for the recipe in the property view:

Operating recipes

10.4 Recipe application

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-11

Depending on the extent of the recipe, you either configure a recipe view or create a recipe

screen.

10.4.5 Scenario: Automatic production sequence

Objective

You want production to be executed automatically. The production data should be

transferred directly to the PLC either from the data storage medium in the HMI device or

from an external data storage medium. The production data do not have to be displayed.

Operating recipes

10.5 Displaying recipes

MP 370 (WinCC flexible)

10-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Sequence

Production can be controlled using one or more "Scripts", which transfer production data

records automatically to the PLC. The sequence can be checked using the return values of

the utilized functions.

Configuration in WinCC flexible

You can implement the automatic production sequence with available system functions. The

"ImportDataRecords" system function loads data records from a CSV file to the data

medium. The "SetDataRecordTagsToPLC" system function transfers a data record from the

data storage medium to the PLC.

10.5 Displaying recipes

10.5.1 Viewing and editing recipes in Runtime

Introduction

The WinCC flexible ES offers you two configuration options of viewing and editing recipes

and their corresponding data records in Runtime on the HMI device:

• Recipe view

• Recipe screen

Recipe view

The recipe view is a screen object that is configured in the "Screens" editor. For example,

you can specify what operating function the recipe view will have in Runtime:

Operating recipes

10.5 Displaying recipes

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-13

The recipe view shows recipe data records in tabular form. The Recipe view is particularly

useful if data records are small in size or only a few values are to be modified.

Simple recipe view

On HMI devices which have a display smaller than 6" (e.g. OP 77B), the simple Recipe view

is used to display and edit recipes.

The simple recipe view consists of three areas:

• Recipe selection

• Recipe data record selection

• Recipe entries

In the simple recipe view, each area is shown separately on the HMI device. The simple

recipe view always begins with the recipe selection.

Recipe screen

A recipe screen is a process screen with a customized input screen form that you create by

setting up input/output fields and other screen objects in the "Screens" editor. This makes it

possible for you to input parameter data in the context of machine visualization. The I/O

fields for a recipe can be distributed over multiple recipe screens, which allows you a topical

organization of recipe elements. The operating functions for the recipe screens must be

configured explicitly in the process screens.

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

10-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

10.5.2 Behavior of the recipe view in Runtime

Screen change

If you change to another screen and have not yet saved changes to the recipe data in the

recipe view, you will be prompted to save the recipe data. The recipe name and the name of

the recipe record are displayed to show which recipe data have not been saved yet.

If you change to a process screen that contains a recipe view with loaded recipe data, the

recipe data will be automatically updated.

Operating the recipe view with softkeys

The Recipe view can be operated with function keys, e.g. when the HMI device does not

have touch functionality. System functions allow you to assign functions such as "Save data

record" to the function keys of the HMI device.

10.6 Recipe data record administration

10.6.1 Recipe data record administration

Recipe data record administration

In Runtime you can, based on the configuration

• Create new recipe data records

• Copy recipe data records

• Edit recipe data records

• Delete recipe data records

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-15

That is, you can either edit recipe data records in the recipe view or screen, or import recipe

data records from a CSV file.

Creating new recipe records

1. Select the recipe on the HMI device in which you want to create a new recipe data

record.

2. Use the "Add data record" button in the recipe view or the corresponding button on the

HMI device that has this function.

A new data record with the next available number will be created. If you change the new

data record number of an existing data record number, the data record is overwritten.

3. Enter a name for the recipe data records.

4. Enter the values for the recipe data records.

The configuration data may already contain default values for the recipe data record.

5. Use the "Save" button in the recipe view or the corresponding button on the HMI device

that has this function.

Result

The new recipe data records will be saved to the selected recipe. If the recipe data records

already exists, a system alarm will be output to the screen.

Copying a recipe data record

You copy a recipe record by saving it under a new name.

1. Select the recipe on the HMI device in which you want to edit an existing recipe data

record.

2. Select the recipe data record that you want to edit on the HMI device.

3. Assign a new name to the recipe data record.

As soon as you close the "Recipe data record" input field, the next free recipe data record

number will be automatically assigned to the recipe data record. You may change the

recipe data record number.

4. Use the "Save" button in the recipe view or the corresponding button on the HMI device

that has this function.

Result

The recipe data record is stored under the new name.

Modify recipe record

1. Select the recipe on the HMI device in which you want to edit an existing recipe data

record.

2. Select the recipe data record that you want to edit on the HMI device.

3. Replace the old values with new ones.

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

10-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

4. Use the "Save" button in the recipe view or the corresponding button on the HMI device

that has this function.

Result

The modified values are applied to the recipe data record.

Delete recipe data record

1. Select the recipe on the HMI device in which you want to delete an existing recipe data

record.

2. Select the recipe data record that you want to delete on the HMI device.

3. On the recipe view, select "Delete data record", or use the relevant HMI device button

which is assigned this function.

Result

The recipe data record is deleted from the data medium of the HMI device.

10.6.2 Synchronizing a recipe data record

Introduction

In Runtime, differences between the indicated values and the actual values of the recipe

tags may arise as a result of data input in recipe views or modification of recipe tags.

Depending on the configuration, you can synchronize the values displayed in the recipe view

with the recipe tags and values of the PLC. This synchronization is performed for each one

of the recipe tags contained in the recipe data record.

Requirements

A recipe data record is displayed in the recipe view. The value of recipe tags can be

changed, for example by teach-ins.

Procedure

1. Use the "Synchronization with controller" button in the recipe view or the corresponding

button that has this function.

Result

• The system always updates the current value of the recipe view with the up-to-date

recipe tag value.

• When the value shown in the recipe view is more recent than the current recipe tag value,

the system writes this value to the recipe tag.

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-17

10.6.3 Read recipe data record from PLC

Introduction

You can read values from the PLC and write them to a recipe data record. For example, you

can do this in machine teach-in mode in order to save the positioning data of axes as a

recipe data record.

The read values are written to the recipe record that is currently displayed on the HMI

device.

Procedure

1. Select the recipe on the HMI device.

2. On the HMI device, select the recipe data record of which you want to fetch the values

from the PLC.

3. Use the "Read from PLC" button in the recipe view or the corresponding button on the

HMI device that has this function.

4. Use the "Save" button in the recipe view or the corresponding button on the HMI device

that has this function.

Result

The values are read from the PLC, visualized on the HMI device and saved to the recipe

data record.

10.6.4 Transfer recipe record to PLC

Introduction

You can edit recipes offline or online.

• Offline: The data are transferred to the PLC after the relevant command is executed.

• Online: The data are transferred immediately to the PLC

In the recipe view, data are always edited offline. The configuration of the recipe screen

determines whether the recipe data are edited offline or online.

When you edit data offline, you have to transfer the changed data to the PLC.

Procedure

1. Select the recipe on the HMI device.

2. On the HMI device, select the recipe data record of which you want to transfer the values

to PLC.

3. Use the "Write to PLC" button in the recipe view or the corresponding button on the HMI

device that has this function.

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

10-18 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Result

The values of the recipe record are transferred to the PLC.

10.6.5 Exporting and importing recipe data records

Introduction

Based on your configuration, you can either export recipe data records to a CSV file for

editing in MS Excel, for example, or import these from a CSV file. The extent to which you

can influence these processes is determined by the project configuration. Various input

boxes may be configured on the user interface:

• Input of the path to the CSV file

• Selection of the recipe data records for export

• Overwriting an existing CSV file

Export recipe data record

Requirements

Export functions are configured.

Procedure

1. Customize the export settings on the user interface of the HMI device, for example, by

setting the path to the CSV file.

2. Press the button or the key on the HMI device configured with the "Export recipe records"

function.

Result

The recipe data record are exported to a CSV file.

Note

New data records created in Runtime can be exported to an external file.

Importing recipe records

Requirements

Import functions are configured.

Operating recipes

10.6 Recipe data record administration

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-19

Procedure

1. Customize the import settings on the user interface of the HMI device, for example, by

setting the path to the CSV file.

2. Use the button or the key on the HMI device which is assigned the "Import recipe

records" function.

Result

The recipe data record are imported. If the structure of the CSV file is different from the

recipe structure, deviations are treated as follows:

• Any additional values in the CSV file will be rejected.

• If the CSV file contains values of the wrong data type, the configured default value is set

in the recipe record.

Example:

The CSV file contains values that show the tank contents and were input as floating point

numbers. However, the corresponding recipe tag expects an integer value. In this case,

the system discards the imported value and uses the configured default.

• The system also applies the configured default value to the recipe data record if the CSV

file contains an insufficient number of values.

10.6.6 Reactions to modifications of the recipe structure

Introduction

Engineering for the purpose of machine retrofitting may also influence the recipe structure.

Previously created recipe data records can nevertheless continue to be used.

Effects

If the structure of the recipe record is different from the defined address ranges in the PLC,

deviations are handled as follows:

• Any additional values in the recipe record will be rejected.

• If the recipe record contains values of the incorrect data type, the default will be used in

the recipe record.

Example: The recipe record contains values that show the tank contents and were input

as floating point numbers. However, the corresponding recipe tag expects an integer

value. In this case, the transferred value is rejected and the default value is used.

The system also applies the default value to the recipe data record, if the recipe data

record contains an insufficient number of values.

Caution

When a tag is renamed, the assignment is lost.

Operating recipes

10.7 Example

MP 370 (WinCC flexible)

10-20 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

10.7 Example

10.7.1 Example: Creating a recipe

Task

In this example, you create three recipes for a fruit juice mixing machine. The fruit juice

mixing machine is to be used to produce orange, apple, and tropical fruit flavors, based on

mixing ratios for fruit drinks, nectar, and juice.

Settings

The settings relate to an HMI device which is connected to a SIMATIC S7-300 or SIMATIC

S7-400 via MPI.

In this example, you need the following tags, flags, recipes, and recipe data record values:

Tags:

Name PLC connection Address Type

Liter water Yes DB 120, DBW 0 Integer

Liter concentrate Yes DB 120, DBW 4 Integer

Kilo sugar Yes DB 120, DBW 8 Integer

Gram flavoring Yes DB 120, DBW 12 Integer

Flag:

Name Address

Data record DB 100, DBW 0

Recipe (basic settings):

Recipe element Associated tag

Liter water Liter water

Liter concentrate Liter concentrate

Kilo sugar Kilo sugar

Gram flavoring Gram flavoring

Recipe data record values:

Data record name Liter water Liter concentrate Kilo sugar Gram flavoring

Fruit drink 30 70 45 600

Nectar 50 50 10 300

Juice 5 95 3 100

Operating recipes

10.7 Example

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-21

Procedure

1. Create the following tags with the settings indicated earlier: Liter water, Liter concentrate,

Kilo sugar and Gram flavoring.

2. Create the orange, apple, and tropical fruit recipes with the settings indicated above.

Figure 10-1 Recipe with recipe elements

3. Configure each recipe in such a way that you can edit the recipe data records on a recipe

screen. The values of the recipe tags should not be transferred automatically to the PLC.

4. Create the data records indicated above in each recipe. Enter the values indicated above

in each of the data records.

Figure 10-2 Recipe with recipe data record values

Result

The orange, apple, and tropical fruit flavor recipes have been created. In the "Configure

recipe screen" example, you create a recipe screen in which you create an individual input

screen form.

10.7.2 Example: Configuring a recipe screen

Task

In this example, you create a recipe screen for the visualization of values of the fruit juice

mixing machine. You use a recipe view to select the recipes and their associated recipe data

records. You should be able to load and save the values of the recipe data records, and

transfer them to and read them from the PLC.

Operating recipes

10.7 Example

MP 370 (WinCC flexible)

10-22 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Requirements

The "Creating a recipe" sample application has been carried out.

The "Fruit juice mixing machine" process screen has been created and is opened.

Settings

In this example, you need the following tags and buttons with the indicated settings:

Tags:

Name PLC connection Type

RecipeNumber No Integer

Data record number No Integer

Buttons:

Labeling Configured event System function

Load Press LoadDataRecord

Save Press SaveDataRecord

Data to PLC Press Write data record tags to PLC

Data from the PLC Press GetDataRecordTagsFromPLC

Procedure

1. Drag-and-drop the "Liter water", "Liter concentrate", "Kilo sugar", and "Gram flavoring"

tags from the object view to the "Fruit juice mixing machine" process screen.

Four I/O fields are created and linked by the specified tags.

2. Configure a recipe view containing only the drop-down lists for the recipe name and data

record name. Link the recipe view to the "Recipe number" and "Data record number"

(recipe data record number) tags in the "General" group in the property view.

Operating recipes

10.7 Example

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 10-23

3. Assign the settings described above to each one of the four buttons. Transfer each

"Recipe number" and "Data record number" tag as a parameter for the recipe number

and recipe data record number.

Result

In Runtime, you can select the recipe and the associated recipe data record from the recipe

view. Click "Load" to load the recipe data record values and display these in the configured

I/O fields. Click "To PLC" to write the recipe data record values to the associated tags and to

transfer the recipe data record values to the PLC.

Operating recipes

10.7 Example

MP 370 (WinCC flexible)

10-24 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 11-1

Maintenance/Service 11

11.1 Clean screen/keyboard foil

11.1.1 General information

Introduction

Clean the HMI device screen or keyboard foil at regular intervals. Use a damp cloth.

Caution

Cleaning the keyboard foil of key devices

Clean the HMI device after it has been switched off. This ensures that functions are not

inadvertently triggered by touching the keys or the touch screen.

Cleaning agents

Use only water with liquid soap or a screen cleaning foam. Never spray the cleaning agent

directly onto the screen. Apply it to a cloth. Never use aggressive solvents or scouring

powder.

11.1.2 Notes on the touch panel

Clean screen

Only applies to HMI devices with a touch screen:

The HMI device touch screen can be cleaned when switched on and when operating

normally if touch screen input has been suppressed by means of an appropriately configured

operating element (Clean Screen). After the Clean Screen function has been activated, all

input via the touch screen operating elements is deactivated for a defined period of time. The

time remaining until the end of operating suppression is indicated by a progress bar.

Maintenance/Service

11.2 Replacing the optional backup battery

MP 370 (WinCC flexible)

11-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Notice

Suppressing operating elements

Only clean the screen during operation when Clean Screen is activated. Pay attention to the

end of operating suppression by the Clean Screen.

Otherwise, incorrect operations may be initiated.

Protective foil

A protective foil is available for the touch screens on HMI devices. The necessary ordering

information is provided in the Siemens Catalog ST 80. The protective foil is not part of the

material supplied with the HMI device.

The self-adhesive foil prevents the screen being scratched and soiled. In addition, the matt

surface of the foil reduces reflections in disadvantageous lighting conditions.

The protective foil can be removed as necessary without leaving any adhesive residue on

the screen.

Caution

Remove protective foil

Never use sharp or pointed tools, such as a knife, to remove the protective foil. This may

damage the touch screen.

11.2 Replacing the optional backup battery

Function of the backup battery

An optional backup battery is available for the HMI device. The battery ensures that in the

event of a power failure, the HMI device's internal hardware clock continues to run.

Under normal operating conditions, the battery has a service life of approx. four years. It is

not supplied with the HMI device.

Supply source

The battery can be ordered from the Siemens spare parts service. It is shipped ready for

installation with a cable and connector. Please refer to the Siemens Catalog ST80 for the

order number.

Maintenance/Service

11.2 Replacing the optional backup battery

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 11-3

Requirements

Caution

Change the battery while power is still being supplied to ensure the internal hardware clock

continues to run.

The battery must be changed by a properly qualified person.

Before replacing the battery, refer to the ESD Guidelines.

Procedure

1. Unplug the battery cable connector from the two-pin socket in the HMI device.

2. The battery is normally secured to the back of the HMI device by two cable ties. Cut the

cable ties, using pliers for instance, and remove the empty battery.

3. Secure the new battery with two cable ties to the back of the HMI device.

4. Insert the battery lead connector back into the socket. The plug is coded to prevent

reversed poling.

General information

Please observe the following safety notes to ensure correct handling and disposal of lithium

batteries:

Warning

The lithium battery can explode if not handled properly. The lithium battery should:.

- never be charged

- not be opened

- not be short-circuited

- be safeguarded against reversed poling

- of 100 °C

- be protected against direct sunlight

Do not allow condensation to form on batteries.

If you have to ship a battery, ensure compliance with the Dangerous Goods Ordinance for

the shipping agent concerned (coding obligation).

Treat used lithium batteries as special waste. Pack them separately in leakproof plastic bags

for disposal.

Maintenance/Service

11.2 Replacing the optional backup battery

MP 370 (WinCC flexible)

11-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

See also

Backup battery (Page 1-9)

ESD guidelines (Page A-2)

Interfaces (Page 4-4)

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 12-1

Technical Specifications 12

12.1 Dimension drawings

12.1.1 Dimensions MP 370 12" Touch

Unit dimensions

Dimensions of the MP 370 12" Touch:

Technical Specifications

12.1 Dimension drawings

MP 370 (WinCC flexible)

12-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Side viewFront view

Plan view

335

275

309.4

247.4

Figure 12-1 Dimensions of the MP 370 12" Touch

Technical Specifications

12.1 Dimension drawings

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 12-3

12.1.2 Dimensions MP 370 15" Touch

Unit dimensions

Dimensions of the MP 370 15" Touch:

400 69 10

366

310

288

Side viewFront view

Plan view

Figure 12-2 Dimensions of the MP 370 15" Touch

Technical Specifications

12.1 Dimension drawings

MP 370 (WinCC flexible)

12-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

12.1.3 Dimensions MP 370 12" Key

Unit dimensions

Dimensions of the MP 370 12" Touch:

288

176

483

310

465

235

59+1

448

178 178

Figure 12-3 Dimensions of the MP 370 12" Key

Technical Specifications

12.2 Technical specifications

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 12-5

12.2 Technical specifications

Technical specifications

Housing MP 370 12" Key MP 370 12" Touch MP 370 15" Touch

External dimensions (W x H) 483 mm x 310 mm 335 mm x 275 mm 400 mm x 310 mm

Installation cutout (W x H) 450+1 mm x 290+1 mm 310+1 mm x 248+1 mm 368+1 mm x 290+1 mm

Installation depth 59 mm 59 mm 69 mm

Degree of protection

Front

Rear panel

IP65/NEMA 4x INDOOR USE ONLY

IP20

Weight Approx. 5,1 kg Approx. 4,5 kg Approx. 5.7 kg

Processor

Type 64 bit RISC CPU

Memory

Memory Free for user data: 12 MB flash memory (max. 7 MB of which is for WinCC flexible

configurations)

Bulk storage

• Slot for CF card e.g. ATA Flash card

• Slot for PC card E.g.

• ATA Flash card

• SRAM card

• NE2000-compatible Ethernet card

Software

Operating system Microsoft Windows CE

Color display MP 370 12" Key MP 370 12" Touch MP 370 15" Touch

Type TFT LCD TFT LCD with touch panel (analog resistive)

Active screen diagonal 12,1 " 12,1 " 15,1 "

Resolution (pixels) 800 x 600 (Super VGA) 1024 x 768 (XGA)

Possible colors 256

Back-lighting CCFL tubes

Half brightness life 1) approx. 50,000 hours

Technical Specifications

12.2 Technical specifications

MP 370 (WinCC flexible)

12-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

1) Time period the brightness of the lighting tube only achieves 50% of its original value. The

specified value depends on the operating temperature.

Keyboard MP 370 12" Key

Type Membrane keyboard

System keys with dedicated functions 38 (3 with LEDs)

Configurable function keys

Number

for local assignment

Labeling

36 (with LEDs)

System-specific with labeling strips

Acoustic acknowledgement MP 370 12" Touch / MP 370 15" Touch

In the case of touch control × (can be disabled)

Power supply MP 370 12" Key MP 370 12" Touch MP 370 15" Touch

Rated voltage +24 V DC

Permissible range +24 V DC -15%, +20%

Max. permissible transients 35 V (500 msec)

Time between two transients Min. 50 s

Power consumption

Typical:

Max. constant current:

Power on current surge I2t:

Approx. 0,6 A

Approx. 0,9 A

Approx. 0.5 A2s

Approx. 0,6 A

Approx. 0,9 A

Approx. 0.5 A2s

Approx. 1,4 A

Approx. 1.8 A

Approx. 0.5 A2s

Fuse, internal Electronic

Backup battery (option)

Type Lithium battery

Voltage/Capacity 2) 3.6 V / approx. 1.5 Ah

Service life Approx. 4 years

Technical Specifications

12.3 EMC requirements

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 12-7

Network connection

Type 1 x Ethernet (10/100 Mbit)

Ambient conditions MP 370 12" Key MP 370 12" Touch / MP 370 15" Touch

Installation position

Max. permissible angle of inclination

without external ventilation

Vertical

±35°

Max. permissible ambient temperature

Operation

• Vertical installation 0 ... +50 °C

• Installation angled from the

perpendicular to max. 35°

0 ... +35 °C

• Shipping, storage -20 ... +60 °C

Relative humidity

Operation, transport, storage Max. 85%, no condensation

Shock loading

Operation

Shipping, storage

15 g / 11 ms

25 g / 6 ms

Vibration

Operation

Shipping, storage

0,075 mm (10 - 58 Hz) 1 g (58 - 500 Hz)

3.5 mm (5 - 8.5 Hz) 1 g (8.5 - 500 Hz)

Barometric pressure

Operation

Shipping, storage

706...1030 hPa

581...1030 hPa

12.3 EMC requirements

EMC requirements

Compliance of the named products with the regulations of Directive 89/336 EEC is verified

by conformance with the following standards:

Noise immunity Norms

Static discharge (contact discharge/air

discharge)

EN 61000-4-2 6 kV/8 kV

RF irradiation EN 61000-4-3 10 V/m, 80% AM,

1 kHz

Pulse modulation ENV 50204 900 MHz ±5 MHz

10 V/meff., 50% ED, 200 Hz

Technical Specifications

12.4 Interface description

MP 370 (WinCC flexible)

12-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Noise immunity Norms

RF conduction EN 61000-4-6 150 kHz - 80 MHz

10 V, 80% AM, 1 kHz

Burst interference EN 61000-4-4

Supply lines

Process data lines

Signal lines

2 kV

1 kV

Surge coupling

Power supply cable

EN 61000-4-5 1 kV with choke,

Type DEHNrail (Order No. 901 104)

2 kV with choke,

Type DEHNrail (Order No. 901 104)

Magnetic fields EN 61000-4-8 30A/m 50/60 Hz

Radio interference

Radio interference level complying to

EN 55011

Class A

12.4 Interface description

IF1A

15 9

Table 12-1 15-pin Cannon connector

Pin RS 232 TTY General

1 Screening

2 - RXD- RXD-

3 RXD - -

4 TXD - -

5 CTS - -

6 - TXD+ -

7 - TXD- RTS

8 Screening

9 - RXD+ -

10 RTS - -

11 - +20 mA -

12 GND

Technical Specifications

12.4 Interface description

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 12-9

Pin RS 232 TTY General

13 - +20 mA -

14 +5 V/100 mA

15 GND

IF1B

Table 12-2 9-pin Sub-D socket (configuration via switch)

Pin RS-422 RS 485 / PROFIBUS-DP / MPI

1 N.C.

2 N.C.

3 TXD+ Data B

4 RXD+ RTS-AS

5 GND (floating)

6 +5 V (floating)

7 N.C.

8 TXD- Data A

9 RXD- -

IF2

Table 12-3 9-pin Sub-D plug (pin)

Pin RS 232

1 DCD

2 RXD

3 TXD

4 DTR

5 GND

6 DSR

7 RTS

8 CTS

9 RI

Technical Specifications

12.4 Interface description

MP 370 (WinCC flexible)

12-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Ethernet interface

Table 12-4 RJ45 plug connection

Pin RJ45

1 10BaseT: TX+

2 10BaseT: TX-

3 10BaseT: RX+

4 -

5 -

6 10BaseT: RX-

7 -

8 -

USB interface

Table 12-5 USB standard plug

Pin USB

1 +5V

2 +5V

3 USB-DM

4 USB-DP

5 0V

6 0V

See also

Connecting the PLC (Page 4-11)

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-1

Appendix A

A.1 Certificates and Directives

A.1.1 Approvals

Approvals

As of the date of delivery, the following approvals have been granted or their application is

pending. Please refer to the rating plate on the back of the HMI device for identification.

Warning

Personal injury and equipment damage can occur.

Personal injury and equipment damage can occur in hazardous areas if a plug connection is

disconnected from the HMI device while the system is running.

In hazardous areas, turn off the power to the HMI device when disconnecting the

connectors.

DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS LOCATION IS KNOWN TO BE

NON HAZARDOUS.

Approvals

CE approval EMC Directives

C-Tick EMC radio interference, Australia

UL approval UL Recognition Mark 1)

Underwriters Laboratories (UL) complying with

Standard UL 508,

File E 116536

UL approval In accordance with the UL/CSA Approval

Agreement

Ex Zone 2/22 Ex zone, Europe

EN 50021, EN 50281-1-1

Appendix

A.1 Certificates and Directives

MP 370 (WinCC flexible)

A-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Approvals

FM approval FM approval

Complying with Factory Mutual Approval

Standard Class Number 3611 Hazardous

(classified) Locations Class I, Division 2, Group

A, B, C, D

1) The UL and CSA file numbers are dependent on the production site. The numbers specified

here changes according to the change of production site.

A.1.2 ESD guidelines

What does ESD mean?

Virtually all present-day, electronic modules incorporate highly integrated MOS devices or

components. For technological reasons, these electronic components are very sensitive to

overvoltage and, consequently, to electrostatic discharge. Therefore, they are identified as

follows:

• ESD – Electrostatically Sensitive Devices

• ESD – Electrostatic Sensitive Devices

The following symbol on cabinet plates, mounting racks and packages draws attention to the

use of ESD and, thus, to the contact sensitivity of the assemblies concerned:

Figure A-1 Symbol for ESD

ESDs may be destroyed by voltages and energies that are undetectable to a human.

Voltages of this kind occur as soon as a device or an assembly is touched by a person who

is not grounded against static electricity. ESDs exposed to such over voltages may not

immediately be detected as defective. In the majority of cases, faulty behavior may occur

only after a long period of operation.

Precautions against electrostatic discharge

Most plastics are capable of carrying high charges. It is therefore imperative that they be

kept away from ESDs.

When working with electrostatically sensitive components, make sure that the person, the

workstation and the packaging are properly grounded.

Appendix

A.1 Certificates and Directives

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-3

Handling ESD assemblies

A general rule is that ESDs should be touched only when necessary, for example, when

maintenance is required.

Only touch devices if

• you are grounded by permanently wearing an ESD wrist strap or

• you are wearing ESD shoes or ESD shoe-grounding protection straps in conjunction with

an ESD floor.

Before you touch an electronic assembly, your body must be discharged. The simplest way

of doing this is to touch a conductive, grounded object immediately beforehand, e.g. bare

metal parts of a cabinet, water pipe etc.

ESDs should not be brought into contact with charge-susceptible and highly insulating

materials such as plastic films, insulating tabletops and items of clothing containing synthetic

fibers.

Assemblies should be deposited only on conductive surfaces, e.g. tables with an ESD

coating, conductive ESD cellular material, ESD bags or ESD shipping containers.

Do not place ESDs near visual display units, monitors or television sets (minimum distance

to screen > 10 cm).

Never touch ESDs so that contact is made with module connections or conductor rails.

Measuring ESD assemblies

Perform measurements on ESD assemblies only when

• the measuring instrument is grounded, e.g. by means of a grounded conductor or

• the measuring head has been briefly discharged before measurements are made with a

potential-free measuring instrument, e.g. by touching a bare metal control cabinet.

When soldering, use only grounded soldering irons.

Shipping ESD assemblies

Always store and ship ESD assemblies and devices in conductive packing, e.g. metallized

plastic boxes, metal boxes.

• Packing ESD

If packing is not conductive, ESDs must be conductively wrapped before they are packed.

Use conductive foam rubber, ESD bags, domestic aluminum foil or paper, for example;

never use plastic bags or foils.

• ESD with fitted battery

With assemblies containing fitted batteries, make sure that the conductive packing does

not come into contact with batteries or short-circuit them. If necessary, cover the battery

terminals beforehand with suitable insulating material.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

A.2 System alarms

Introduction

System alarms on the HMI device provide information about internal conditions of the HMI

device and PLC.

The following is an overview of when system alarms occur, their causes and the remedies

available.

Note

System alarms are only displayed when an alarm window has been configured. System

alarms are issued in the language currently set on the HMI device.

System alarm parameters

The system alarms may contain parameters which are not decoded for the user but which

are relevant with respect to the cause of an error. They provide a reference to the source

code from the runtime software. These parameters are issued after the text "Error code:".

System alarm parameters

Number Effect/cause Remedy

10000 The print job cannot be started or was canceled

due to an unknown cause. The printer is not

correctly configured. or There is no authorization for

a network printer.

The power supply failed during data transfer.

Check the printer settings, cable connections and the

power supply.

Set up the printer once again. Obtain a network printer

authorization.

If the error persists, contact the Hotline!

10001 No printer is installed or a default printer has not

been selected.

Install a printer and/or select it as the default printer.

10002 The graphics buffer for printing is full. Up to two

graphics are buffered.

Wait before triggering print jobs.

10003 Graphics can be buffered again. -

10004 The buffer for printing lines in text mode (e.g.

alarms) is full. Up to 1000 lines are buffered.

Wait before triggering print jobs.

10005 Text lines can be buffered again. -

10006 The Windows printing system reports an error.

Refer to the printed text and the error number to

determine the possible causes. Nothing is printed

or the printout is incorrect.

Repeat the action if necessary.

20010 An error has occurred in the specified script line.

The execution of the script was therefore aborted.

Note the system alarms that may have occurred

prior to this.

Select the specified script line in the configuration.

Ensure that the tags used are the allowed types. Check

system functions for the correct number and types of

parameters.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-5

Number Effect/cause Remedy

20011 An error has occurred in a script that was called by

the specified script.

The execution of the script was therefore aborted in

the called script.

Note the system alarms that may have occurred

prior to this.

In the configuration select the script that has been called

directly or indirectly by the specified script.

Ensure that the tags used are the allowed types.

Check system functions for the correct number and types

of parameters.

20012 The configuration data is inconsistent. The script

could therefore not be generated.

Recompile the configuration.

20013 The script components from WinCC flexible runtime

are not correctly installed. Therefore, no scripts can

be executed.

Reinstall WinCC flexible runtime.

20014 The system function returns a value that is not

written in any return tag.

Select the specified script in the configuration.

Check whether the script name has been assigned a

value.

20015 Too many scripts have been triggered in quick

succession. When more than 20 scripts are queued

for processing, any subsequent scripts are rejected.

In this case, the script indicated in the alarm is not

executed.

Find what is triggering the scripts. Extend the times, e.g.

the polling time of the tags which trigger the scripts.

30010 The tag could not accept the function result, e.g.

when it has exceeded the value range.

Check the tag type of the system function parameter.

30011 A system function could not be executed because

the function was assigned an invalid value or type

in the parameter.

Check the parameter value and tag type of the invalid

parameter. If a tag is used as a parameter, check its

value.

40010 The system function could not be executed since

the parameters could not be converted to a

common tag type.

Check the parameter types in the configuration.

40011 The system function could not be executed since

the parameters could not be converted to a

common tag type.

Check the parameter types in the configuration.

50000 The HMI device is receiving data faster than it is

capable of processing. Therefore, no further data is

received until the data currently available has been

processed. Data exchange then resumes.

50001 Data exchange resumes. -

60000 This alarm is generated by the function

“DisplaySystemEvents”. The text to be displayed is

transferred to the function as a parameter.

60010 The file could not be copied to the defined path

because one of the two files is currently open or the

source/target path is not available.

It is possible that the Windows user has no access

rights to one of the two files.

Restart the system function or check the paths of the

source/target files. Using Windows NT/2000/XP: The user

executing WinCC flexible Runtime must be granted

access rights for the files.

60011 An attempt was made to copy a file to itself.

It is possible that the Windows user has no access

rights to one of the two files.

Check the path of the source/target file.

Using Windows NT/2000/XP with NTFS: The user

executing WinCC flexible Runtime must be granted

access rights for the files.

70010 The application could not be started because it

could not be found in the path specified or there is

insufficient memory.

Check whether the application exists in the specified path

or close other applications.

70011 The system time could not be modified. Check the time which is to be set.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

The error message only appears in connection with

area pointer "Date/time PLC". Possible causes:

• An invalid time was transferred in the job

mailbox.

• The Windows user does not have the right to

modify the system time.

If the first parameter in the system alarm is

displayed with the value 13, the second parameter

indicates the byte containing the incorrect value.

Using Windows NT/2000/XP: The user executing WinCC

flexible Runtime must be granted the right to change the

system time of the operating system.

70012 An error occurred when executing the function

"StopRuntime" with the option "Runtime and

operating system".

Windows and WinCC flexible Runtime are not

closed.

One possible cause is that other programs cannot

be closed.

Close all programs currently running.

Then close Windows.

70013 The system time could not be modified because an

invalid value was entered. Incorrect separators may

have been used.

Check the time which is to be set.

70014 The system time could not be modified. Possible

causes:

• An invalid time was transferred.

• The Windows user does not have the right to

modify the system time.

• Windows rejects the setting request.

Check the time which is to be set.

Using Windows NT/2000/XP: The user executing WinCC

flexible Runtime must be granted the right to change the

system time of the operating system.

70015 The system time could not be read because

Windows rejects the reading function.

70016 An attempt was made to select a screen by means

of a system function or job. This is not possible

because the screen number specified does not

exist.

or: a screen could not be generated due to

insufficient system memory.

Check the screen number in the function or job with the

screen numbers configured.

Assign the numbers to a screen, if necessary.

70017 Date/time is not read from the area pointer because

the address set in the PLC is either not available or

has not been set up.

Change the address or set up the address in the PLC.

70018 Acknowledgment that the password list has been

successfully imported.

70019 Acknowledgment that the password list has been

successfully exported.

70020 Acknowledgment for activation of alarm reporting. -

70021 Acknowledgment for deactivation of alarm

reporting.

70022 Acknowledgment to starting the Import Password

List action.

70023 Acknowledgment to starting the Export Password

List action.

70024 The value range of the tag has been exceeded in

the system function.

The calculation of the system function will not be

performed.

Check the desired calculation and correct it if necessary.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-7

Number Effect/cause Remedy

70025 The value range of the tag has been exceeded in

the system function.

The calculation of the system function will not be

performed.

Check the desired calculation and correct it if necessary.

70026 No other screens are stored in the internal screen

memory.

No other screens can be selected.

70027 The backup of the RAM file system has been

started.

70028 The files from the RAM have been copied in the

Flash memory.

The files from the RAM have been copied in the

Flash memory. Following a restart, these saved

files will be copied back to the RAM file system.

70029 Backup of the RAM file system has failed.

No backup copy of the RAM file system has been

made.

Check the settings in the "Control Panel > OP" dialog and

save the RAM file system using the "Save Files" button in

the "Persistent Storage" tab.

70030 The parameters configured for the system function

are faulty.

The connection to the new PLC was not

established.

Compare the parameters configured for the system

function with the parameters configured for the PLC and

correct them as necessary.

70031 The PLC configured in the system function is not an

S7 PLC.

The connection to the new PLC was not

established.

Compare the S7 PLC name parameter configured for the

system function with the parameters configured for the

PLC and correct them as necessary.

70032 The object configured with this number in the tab

order is not available in the selected screen.

The screen changes but the focus is set to the first

object.

Check the number of the tab order and correct it if

necessary.

70033 An e-mail cannot be sent because a TCP/IP

connection to the SMTP server no longer exists.

This system alarm is generated only at the first

attempt. All subsequent unsuccessful attempts to

send an e-mail will no longer generate a system

alarm. The event is regenerated when an e-mail

has been successfully sent in the meantime.

The central e-mail component in WinCC flexible

Runtime attempts, in regular intervals (1 minute), to

establish the connection to the SMTP server and to

send the remaining e-mails.

Check the network connection to the SMTP server and

re-establish it if necessary.

70034 Following a disruption, the TCP/IP connection to

the SMTP server could be re-established.

The queued e-mails are then sent.

70035 The e-mail queue of the central component in

WinCC flexible Runtime responsible for sending e-

mails is full. The e-mail could therefore not be

entered into the queue and therefore not sent.

The cause may be a broken connection to the

SMTP server or an overload resulting from too

much e-mail traffic.

This system alarm is generated only at the first

attempt. The next system alarm is only generated

when at least one e-mail has been successfully

Check if

• the network connection still exists or

• the connection is overloaded (for example, due to

reoccurring system alarms resulting from disruptions).

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

sent to the queue.

70036 No SMTP server for sending e-mails is configured.

A connection to an SMTP server can therefore not

be established and no e-mails can be sent.

The system alarm is generated by WinCC flexible

Runtime the first time an attempt is made to send

an e-mail.

Configure an SMTP server:

In WinCC flexible Engineering System

using "Device settings > Device settings"

In the Windows CE operating system

using "Control Panel > Internet Settings > Email > SMTP

Server"

70037 An e-mail could not be sent for unknown reasons.

The contents of the e-mail will be discarded.

Check the e-mail parameters (recipient, etc.).

70038 The SMTP server has rejected sending or

forwarding an e-mail because the domain of the

recipient is unknown to the server or because the

SMTP server requires authentication.

The contents of the e-mail are lost.

Check the domain of the recipient address or deactivate

the authentication on the SMTP server if possible. SMTP

authentication is currently not used in WinCC flexible

Runtime.

70039 The syntax of the e-mail address is incorrect or

contains illegal characters.

The contents of the e-mail are discarded.

Check the e-mail address of the recipient.

70040 The syntax of the e-mail address is incorrect or

contains illegal characters.

80001 The log specified is filled to the maximum (in

percent) and must be stored elsewhere.

Store the file or table by executing a ‘move’ or ‘copy’

function.

80002 A line is missing in the specified log. -

80003 The copying process for logging was not

successful.

In this case, it is also advisable to check any

subsequent system alarms.

80006 Logging is not possible, resulting in a permanent

loss of the functionality.

In the case of databases, check whether the

corresponding data source exists and restart the system.

80009 A copying action has been completed successfully. -

80010 The storage location was incorrectly entered in

WinCC flexible, resulting in a permanent loss of the

functionality.

Configure the storage location for the respective log

again and restart the system when full functionality is

required.

80012 Log entries are stored in a buffer. If the values are

read to the buffer faster than they can be physically

written (using a hard disk, for example),

overloading may occur and recording is then

stopped.

Archive fewer values.

or:

Increase the logging cycle.

80013 The overload status no longer applies. Archiving

resumes the recording of all values.

80014 The same action was triggered twice in quick

succession. Since the process is already in

operation, the action is only carried out once.

80015 This system alarm is used to report DOS or

database errors to the user.

80016 The logs are separated by the system function

"CloseAllLogs" and the incoming entries exceed the

defined buffer size.

All entries in the buffer will be deleted.

Reconnect the logs.

80017 The incoming entries exceed the defined buffer

size. This can be caused, for example, by several

Stop the copy action.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-9

Number Effect/cause Remedy

copying actions being activated at the same time.

All copy jobs will be deleted.

80018 After executing the system function "OpenAllLogs",

all connections between WinCC flexible and the

logs have been reestablished.

Entries will be rewritten into the logs.

80019 After executing the system function "CloseAllLogs"

all connections between WinCC flexible and all logs

have been severed.

Entries will be written to the buffer and written into

the logs when a connection is re-established.

There is no connection to the storage location and

the data medium may be in the process of being

exchanged.

80020 The maximum number of simultaneously activated

copy actions has been exceeded. Copying is not

executed.

Wait until the current copying actions have been

completed and restart the last copy action.

80021 An attempt was made to delete a log which is still

involved with a copy action. Deletion has not been

executed.

Wait until the current copying actions have been

completed and restart the last action

80022 Using the system function "StartSequenceLog", an

attempt was made to start a sequential log for a log

not configured as such. No sequential log is

created.

Check the project for the following:

• The system function "StartSequenceLog" is

configured correctly.

• The tag parameters are being correctly provided on

the HMI device.

80023 An attempt was made to copy a log to itself.

The log is not copied.

Check the project for the following:

• The system function "CopyLog" is configured

correctly.

• The tag parameters are being correctly provided on

the HMI device.

80024 The system function "CopyLog" is configured not to

permit copying when the target log already contains

data (Parameter: "Mode"). The log is not copied.

If necessary, modify the system function "CopyLog" in the

project. Before initiating the system function, delete the

target log.

80025 You have interrupted the copy process.

Data written up to this point is retained. Deletion of

the target log (if configured) is not executed.

The cancellation is documented by a $RT_ERR$

error entry at the end of the target log.

80026 This notification is issued after all the logs have

been successfully initialized. Values are written to

the logs from this moment on. Prior to this, no

entries are written to the logs even though WinCC

flexible Runtime is running.

80027 The internal Flash memory has been specified as

the storage location for a log. This is not

permissible.

No values will be logged for this log and the log will

not be created.

Configure "Storage Card" or a network path as the

storage location.

80028 The event serves as a status acknowledgment that

initialization of the logs is currently running. No

values are logged until system alarm 80026 is

issued.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

80029 The number of logs specified in the event could not

be initialized. Initialization of the logs has been

completed.

The faulty logs are not available for logging jobs.

Evaluate the additional system alarms generated for this

alarm.

Check the configuration, the ODBC (Open Database

Connectivity) and the specified drive.

80030 The structure of existing log does not match the

expected log structure.

The logging process is stopped for this log.

Delete the existing log data manually in advance.

80031 The log in CSV format is corrupted.

The log cannot be used.

Delete the corrupt file.

80032 Logs can be configured with events. These are

triggered as soon as the log is full. If WinCC flexible

Runtime is started and the log is already full, the

event will not be triggered.

The log specified no longer logs data because it is

full.

Stop the WinCC flexible Runtime, delete the log and

restart the WinCC flexible Runtime.

or:

Configure a button which contains the same actions as

the event and press it.

80033 "System Defined" is selected in the data log as the

data source name. This results in an error. No

logging is made to the database log whereas the

logging to the CSV logs works.

Install MSDE again.

80034 An error has occurred in the initialization of the

logs. An attempt has been made to create tables as

a backup. This did not work. A backup has been

made of the tables of the corrupt log and the log

has been newly started (empty).

No action is necessary. However, it is recommended to

save the backups or delete them to free up memory.

80035 An error has occurred in the initialization of the

logs. An attempt has been made to create backups

of the tables and this has failed. No logging or

backup has been performed.

It is recommended to save the backups or delete them to

free up memory.

110000 The operating mode has been changed. The

operating mode is now 'offline'.

110001 The operating mode has been changed. The

operating mode is now "online".

110002 The operating mode cannot be changed. Check the connection to the PLCs.

Check whether the address area for the area pointer 88

“Coordination" in the PLC is available.

110003 The operating mode of the specified controller has

been changed by the system function

"SetConnectionMode".

The operating mode is now "offline".

110004 The operating mode of the specified controller has

been changed by the system function

"SetConnectionMode".

The operating mode is now "online".

110005 An attempt was made to use the system function

SetConnectionMode to switch the specified PLC to

the online operating mode although the entire

system is in the offline mode. This switchover is not

permissible. The PLC remains in operating mode

"offline".

Switch the complete system to operating mode "online"

and execute the system function again.

110006 The content of the area pointer "User version" does

not match the user version configured WinCC

flexible. WinCC flexible Runtime is therefore

Check:

• The user version entered on the controller

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-11

Number Effect/cause Remedy

closed. • The user version entered in WinCC flexible

120000 The trend is not displayed because an incorrect

axis to the trend or incorrect trend has been

configured.

Change the configuration.

120001 The trend is not displayed because an incorrect

axis to the trend or incorrect trend has been

configured.

Change the configuration.

120002 The trend is not displayed because the tag

assigned tries to access an invalid PLC address.

Check if the data area for the tag exists in the PLC, the

configured address is correct and the value range for the

tag is correct.

130000 The action was not executed. Close the other programs.

Delete files no longer required from the hard disk.

130001 The action was not executed. Delete files no longer required from the hard disk.

130002 The action was not executed. Close the other programs.

Delete files no longer required from the hard disk.

130003 No data medium is inserted. The process is

stopped.

For example, check if

• The correct data medium is being accessed

• The data medium is inserted

130004 The data medium is write-protected. The process is

stopped.

Check whether access has been made to the correct

storage medium. Remove any write protection.

130005 The file is write-protected. The process is stopped. Check whether access has been made to the correct file.

Modify the file attributes, if necessary.

130006 No access to file is possible. The process is

stopped.

For example, check if

• The correct file is being accessed

• The file exists

• Another action is preventing simultaneous access to

the file

130007 The network connection is interrupted.

Data mailboxes cannot be saved or read over the

network connection.

Check the network connection and correct the reason for

the disruption.

130008 The storage card is not available.

Data mailboxes cannot be saved or read to the

storage card.

Insert the storage card.

130009 The specified directory is not on the storage card.

The files that are saved in this directory are not

saved when the HMI device is switched off.

Insert the storage card.

130010 The maximum nesting depth can be exhausted, for

example, when a value change in a script results in

the initiation of another script. The second script in

turn has a value change resulting in the initiation of

another script and so on.

The configured functionality is not provided.

Check the configuration.

140000 Online connection to the PLC has been

successfully established.

140001 Online connection to the PLC has been

disconnected.

140003 No tag updating or writing is executed. Check the connection and whether the PLC is switched

on.

Check the parameter definitions in the Control Panel

using "Set PU/PC interface".

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-12 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

Restart the system.

140004 No tag updating or writing is executed because the

access point or the subrack configuration is

incorrect.

Verify the connection and check whether the PLC is

switched on.

Check the access point or the subrack configuration

(MPI, PPI, PROFIBUS) in the Control Panel with "Set

PU/PC interface".

Restart the system.

140005 No tag updating or writing is executed because the

address of the HMI device is incorrect (possibly too

high).

Use a different HMI device address.

Verify the connection and check whether the PLC is

switched on.

Check the parameter definitions in the Control Panel

using "Set PU/PC interface".

Restart the system.

140006 No tag updating or writing is executed because the

baud rate is incorrect.

Select a different baud rate in WinCC flexible (according

to module, profile, communication peer, etc.).

140007 Tags are not updated or written because the bus

profile is incorrect (see %1).

The following parameters cannot be entered in the

registry:

1: Tslot

2: Tqui

3: Tset

4: MinTsdr

5: MaxTsdr

6: Trdy

7: Tid1

8: Tid2

9: Gap Factor

10: Retry Limit

Check the user-defined bus profile.

Check the connection and whether the PLC is switched

on.

Check the parameter definitions in the Control Panel

using "Set PU/PC interface".

Restart the system.

140008 No tag updating or writing is executed because

baud rate is incorrect. The following parameters

cannot be entered in the registry:

0: General error

1: Incorrect version

2: Profile cannot be entered in the registry.

3: Subnet type cannot be entered in the registry.

4: Target rotation time cannot be entered in the

registry.

5: Highest address (HSA) incorrect.

Check the connection and whether the PLC is switched

on.

Check the parameter definitions in the Control Panel

using "Set PU/PC interface".

Restart the system.

140009 No tag updating or writing is executed because the

module for the S7 communication was not found.

Reinstall the module in the Control Panel using "Set

PU/PC interface".

140010 No S7 communication peer could be found

because the PLC is switched off.

DP/T:

The option “Is not active as the only master” is set

in the Control Panel under “Set PU/PC interface”..

Switch the PLC on.

DP/T:

If only one master is connected to the network, deactivate

the option "Is not active as the only master" in "Set

PU/PC interface".

If there is more than one master connected to the

network, activate them. Do not change any settings

otherwise the bus will be disrupted.

140011 No tag updating or writing is executed because the

communication is interrupted.

Check the connection and that the communication peer is

switched on.

140012 There is an initialization problem (e.g. when WinCC

flexible Runtime has been terminated in the Task

Restart the HMI device.

or:

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-13

Number Effect/cause Remedy

Manager).

or:

Another application (e.g. STEP7) is active with

different bus parameters and the driver cannot be

started with the new bus parameters (e.g.baud

rate).

Start WinCC flexible Runtime first and then the other

applications.

140013 The MPI cable is not plugged in; there is no power

supply.

Check the connections.

140014 "Configured bus address already assigned." Modify the HMI device address in the configuration in

PLC.

140015 Incorrect baud rate

or:

Incorrect bus parameter (e.g. HSA)

or:

OP address > HSA or: incorrect interrupt vector

(interrupt does not arrive at the driver)

Correct the incorrect parameters.

140016 Configured interrupt is not supported by the

hardware.

Change the interrupt number.

140017 Configured interrupt in use by another driver. Change the interrupt number.

140018 The consistency check was deactivated by

SIMOTION Scout. Only one appropriate note

appears.

Activate the consistency check with SIMOTION Scout

again and reload the configuration in the project.

140019 SIMOTION Scout loads a new project to the PLC.

Connection to the PLC is interrupted.

Wait until the end of the reconfiguration.

140020 The version in the PLC and that in the configuration

(FWX file) do not match.

Connection to the PLC is interrupted.

The following remedies are available:

Load the current version in the PLC using SIMOTION

Scout.

Regenerate the project using WinCC flexible ES, close

WinCC flexible Runtime and restart with a new

configuration.

150000 No additional data is read or written. Possible

causes:

• The cable is defective.

• The PLC does not respond, is defective, etc.

• The connection is established via the wrong

interface.

• The system is overloaded.

Check that the cable is plugged in, the PLC is operational

and the correct interface is used.

Reboot the system if the system alarm is displayed

continuously.

150001 Connection is reestablished because the cause of

the interruption has been eliminated.

160000 No additional data is read or written. Possible

causes:

• The cable is defective.

• The PLC does not respond, is defective, etc.

• Connection has been established via the wrong

interface.

• The system is overloaded.

Check that the cable is plugged in, the PLC is operational

and the correct interface is used.

Reboot the system if the system alarm is displayed

continuously.

160001 Connection is reestablished because the cause of

the interruption has been eliminated.

160010 There is no connection to the server because the

server identification (CLS-ID) cannot be

Check the access rights.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-14 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

established.

Values cannot be read or written.

160011 There is no connection to the server because the

server identification (CLS-ID) cannot be

established.

Values cannot be read or written.

For example, check if

• The server name is correct

• The computer name is correct

• The server is registered

160012 There is no connection to the server because the

server identification (CLS-ID) cannot be

established.

Values cannot be read or written.

For example, check if

• The server name is correct

• The computer name is correct

• The server is registered

Note for experienced users:

Interpret the value from HRESULT.

160013 The specified server was started as InProc Server.

This has not been released and may possibly lead

to incorrect behavior because the server is running

in the same process area as the WinCC flexible

Runtime software.

Configure the server as OutProc Server or Local Server.

160014 Only one OPC server project can be started on a

PC/MP. An error message appears when an

attempt is made to start a second project.

The second project has no OPC server functionality

and cannot be located as an OPC server from

external sources.

Do not start a second project with OPC server

functionality on the computer.

170000 S7 diagnostic alarms are not displayed because it

is not possible to log on to the S7 diagnostics with

this unit. The service program is not supported.

170001 The S7 diagnostics buffer cannot be displayed

because communication with the PLC has been

switched off.

Switch the PLC online.

170002 The S7 diagnostics buffer cannot be displayed

because reading in the diagnostics buffer (SZL)

was terminated due to an error.

170003 The display of an S7 diagnostic alarm is not

possible. An internal error %2 has been reported.

170004 The display of an S7 diagnostic alarm is not

possible. An internal error with error class %2 and

error number %3 has been reported.

170007 It is not possible to read in the S7 diagnostics buffer

(SZL) because it was terminated with an internal

error class %2 and error code %3.

180000 A component/OCX receives configuration data with

a version identification which is not supported.

Install a newer component.

180001 The system is overloaded because too many

actions have been activated simultaneously. Not all

the actions can be executed; some are rejected.

Several remedies are available:

• Increase the configured cycle times or basic clock.

• Generate the alarms slower (polling).

• Trigger the scripts and functions at greater intervals.

If the alarm appears more frequently:

Restart the HMI device.

180002 The screen keyboard could not be activated.

Possible cause:

Reinstall WinCC flexible runtime.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-15

Number Effect/cause Remedy

The file “TouchInputPC.exe” was not registered due

to an incorrectly executed Setup.

190000 It is possible that the tag will not be updated. -

190001 The tag is updated following an error status after

the cause of the last error state has been

eliminated (return to normal operation).

190002 The tag is not updated because communication to

the PLC has been interrupted.

Switch on communication via the system function

"SetOnline".

190004 The tag is not updated because the configured

address is not available for this tag.

Check the configuration.

190005 The tag is not updated because the configured PLC

type does not exist for this tag.

Check the configuration.

190006 The tag is not updated because it is not possible to

map the PLC type in the data type for the tag.

Check the configuration.

190007 The tag values are not modified because the

connection to the PLC has been interrupted or the

tag is offline.

Switch to online mode or reestablish connection to the

PLC.

190008 The threshold values configured for the tag have

been violated possibly due to:

• an entered value

• a system function

• a script

Observe the configured or current threshold value of the

tag.

190009 An attempt has been made to assign a value to a

tag which is outside the value range permitted for

this data type.

E.g., a value of 260 entered for a byte tag or a

value of -3 for a word tag without a sign.

Observe the value range for the data type of the tags.

190010 Too many values are being used to describe a tag

(i.e. in a loop triggered by a script).

Values are lost because the maximum of 100

actions have been stored in the buffer.

Increase the time interval between the multi-writing tasks.

190011 Possible cause 1:

The value entered could not be written to the

configured PLC tag because it was either above or

below the value range.

The input is rejected and the original value is reset.

Possible cause 2:

The connection to the PLC has been interrupted.

Ensure that the value entered is within the value range of

the PLC tags.

Check the connection to the PLC.

190012 It is not possible to convert a value from a source

format to a target format. For example:

A value should be assigned to a counter which is

outside the valid, PLC-dependent value range.

A tag of the type Integer should be assigned a

value of the type String.

Check the value range or the data type of the tags.

190100 The area pointer is not updated because the

configured address for this area pointer is not

available.

Type

1 Warning alarms

Check the configuration.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-16 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

2 Alarms

3 PLC acknowledgment

4 HMI device acknowledgment

5 LED mapping

6 Trend request

7 Trend transfer 1

8 Trend transfer 2

No.:

is the consecutive number displayed in WinCC

flexible ES.

190101 The area pointer is not updated because it is not

possible to map the PLC type in the area pointer

type.

Parameter type and no.:

see alarm 190100

190102 The area pointer is updated following an error

status after the cause of the last error state has

been eliminated (return to normal operation).

Parameter type and no.: See alarm 190100.

200000 Coordination is not executed because the address

configured in the PLC does not exist/has not been

set up.

Change the address or set up the address in the PLC.

200001 Coordination is not executed because the address

configured in the PLC does not exist/has not been

written.

Change the address or set up the address in the PLC in

an area which can be written to.

200002 Coordination is currently not being performed

because the address format of the area pointer

does not match the internal storage format.

Internal error

200003 Coordination can be executed again because the

last error status has been eliminated (return to

normal operation).

200004 The coordination may not be executed. -

200005 No additional data is read or written. Possible

causes:

• The cable is defective.

• The PLC does not respond, is defective, etc.

• The system is overloaded.

Check that the cable is plugged in and the PLC is

operational.

Reboot the system if the system alarm is displayed

continuously.

200100 Coordination is not executed because the address

configured in the PLC does not exist/has not been

set up.

Change the address or set up the address in the PLC.

200101 Coordination is not executed because the address

configured in the PLC does not exist/has not been

written.

Change the address or set up the address in the PLC in

an area which can be written to.

200102 Coordination is currently not being performed

because the address format of the area pointer

does not match the internal storage format.

Internal error

200103 Coordination can be executed again because the

last error status has been eliminated (return to

normal operation).

200104 The coordination may not be executed. -

200105 No additional data is read or written. Possible Check that the cable is plugged in and the PLC is

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-17

Number Effect/cause Remedy

causes:

• The cable is defective.

• The PLC does not respond, is defective, etc.

• The system is overloaded.

operational.

Reboot the system if the system alarm is displayed

continuously.

210000 Jobs are not processed because the address

configured in the PLC does not exist/has not been

set up.

Change the address or set up the address in the PLC.

210001 Jobs are not processed because the address

configured in the PLC cannot be written to/read

from.

Change the address or set up the address in the PLC in

an area which can be written to/read from.

210002 Commands are not executed because the address

format of the area pointer does not match the

internal storage format.

Internal error

210003 The job mailbox is processed again because the

last error status has been eliminated (return to

normal operation).

210004 It is possible that the job mailbox is not processed. -

210005 A job mailbox with an illegal number was triggered. Check the PLC program.

210006 An error occurred while attempting to execute the

job mailbox. As a result, the job mailbox will not be

executed. Observe the subsequent/previous

system alarm, if appropriate.

Check the parameters in the job mailbox. Recompile the

configuration.

220001 The tag is not downloaded because the associated

communication driver / HMI device does not

support downloading the data type bool/bit.

Change the configuration.

220002 The tag is not downloaded because the associated

communication driver / HMI device does not

support the data type byte when writing.

Change the configuration.

220003 The communication driver cannot be loaded. The

driver may not be installed.

Install the driver by reinstalling WinCC flexible Runtime.

220004 Communication is terminated and no update is

executed because the cable is not connected or is

defective, etc.

Check the connection.

220005 Communication is running. -

220006 The connection is established to the specified PLC

at the specified interface.

220007 The connection to the specified PLC at the

specified interface is disrupted.

Check if

• The cable is plugged in

• The PLC is OK

• The correct interface is used

• The configuration is OK (interface parameters,

protocol settings, controller address).

Reboot the system if the system alarm is displayed

continuously.

220008 The communication driver cannot access the

specified interface or open it. It is possible that

another program is using this interface or an

interface is being used which is not available on the

target device.

There is no communication to the PLC.

Close all the programs which access the interface and

restart the computer.

Use another interface available in the system.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-18 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

230000 The value entered could not be accepted. The

entered value is rejected and the previous value is

restored.

Either the value range has been exceeded or

impermissible characters were entered.

Enter a permissible value.

230002 Since the user currently logged on does not have

the proper authorization, the input is rejected and

the previous value is restored.

Log on as a user with sufficient rights.

230003 Changeover to the specified screen is not executed

because the screen is not available/configured. The

current screen remains selected.

Configure the screen and check the selection function.

230005 The value range of the tag has been exceeded in

the I/O field.

The original value of the tag is retained.

Take the value range of the tag into consideration when

entering value.

230100 During navigation in the web browser, a message

which may be of interest to the user is issued.

The web browser continues to run, but may not

(fully) display the new page.

Navigate to another page.

230200 The connection to the HTTP channel was

interrupted due to an error. This error is explained

by another system alarm.

Data is no longer exchanged.

Check the network connection.

Check the configuration of the server.

230201 The connection to HTTP channel has been

reestablished.

Data is exchanged.

230202 WININET.DLL has detected an error. This error

usually occurs when it is not possible to make a

connection to the server or the server rejects the

attempt to make a connection because the client

lacks the authorization.

An unknown server certificate can also be the

cause when the connection is encoded through

SSL.

The text of the error message provides more

information.

This text is always in the language of the Windows

installation since it originates from Windows.

Process values are no longer exchanged.

Depending on the cause:

When a connection cannot be made or a timeout occurs:

• Check the network connection and the network.

• Check the server address.

• Check if the web server is actually running on the

target computer.

In the absence of an authorization:

• Configured user name and/or password do not match

those on the server. Match them.

When the server certificate is rejected:

Certificate signed by an unknown CA ( ):

• Either set the configuration to ignore this point, or

• Install a certificate that has been signed with a root

certificate known to the client computer.

If the date of the certificate is invalid:

• Either set the configuration to ignore this point, or

• Install a certificate with a valid date on the server.

If there is an invalid CN (Common Name or Computer

Name):

• Either set the configuration to ignore this point, or

• Install a certificate with a name that corresponds to

that of the server address.

230203 Although a connection can be made to the server,

the HTTP server rejects the connection because

• WinCC flexible Runtime is not running on the

server or

For error 503 Service unavailable: Check if:

WinCC flexible Runtime is running on a server.

The HTTP channel is supported.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-19

Number Effect/cause Remedy

server, or

• The HTTP channel is not supported (503

Service unavailable).

Other errors may occur if the web server does not

support the HTTP channel. The language of the

error text depends on the web server.

Data is not exchanged.

230301 An internal error has occurred. An English text

explains the error somewhat more specific. One

possible cause is insufficient memory, for example.

OCX does not work.

230302 The name of the remote server cannot be

determined.

No connection can be established.

Check the configured server address.

Check if the DNS service of the network is activated.

230303 The remote server is not running on the addressed

computer.

The server address is incorrect.

No connection can be established.

Check the configured server address.

Check if the remote server is running on the target

computer.

230304 The remote server on the addressed computer is

incompatible to VNCOCX.

No connection can be established.

Use a compatible remote server.

230305 The authentication has failed because the

password is incorrect.

No connection can be established.

Configure the correct password.

230306 The connection to the remote server has been

interrupted. This may occur during network

problems.

No connection can be established.

Check if

• The cable is plugged in

• there are network problems.

230307 The connection to the remote server was ended

because

• The remote server was shut down, or

• The user instructed the server to close all

connections.

The connection is closed.

230308 This notification informs you about the

establishment of the connection.

A connection has just been established.

240000 WinCC flexible Runtime is operating in demo mode.

You have no authorization or your authorization is

corrupt.

Load the authorization.

240001 WinCC flexible Runtime is operating in demo mode.

Too many tags are configured for the installed

version.

Load an adequate authorization / powerpack.

240002 WinCC flexible Runtime is operating with a time-

limited standby authorization.

Restore the full authorization.

240003 Authorization cannot be executed.

Without authorization, WinCC will run in demo

mode.

Restart WinCC flexible Runtime or reinstall it.

240004 Error while reading the standby authorization.

WinCC flexible Runtime is operating in demo mode.

Restart WinCC flexible Runtime, install the authorization

or repair the authorization (see Commissioning

Instructions Software Protection).

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-20 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

250000 The tag in the specified line in "Status force" is not

updated because the address configured for this

tag is not available.

Check the set address and then check that the address

has been set up in the PLC.

250001 The tag in the specified line in "Status force" is not

updated because the PLC type configured for this

tag is not available.

Check the set address.

250002 The tag in the specified line in "Status force" is not

updated because it is not possible to map the PLC

type in the tag type.

Check the set address.

250003 No connection could be established to the PLC.

The tags will not be updated.

Check the connection to the PLC. Check that the PLC is

switched on and online.

260000 An unknown user or an unknown password has

been entered in the system.

The current user is logged off the system.

Log on to the system as a user with a valid password.

260001 The logged on user does not have sufficient

authorization to perform the protected functions on

the system.

Log on to the system as a user with sufficient

authorization.

260002 This notification is triggered by the system function

"TrackUserChange".

260003 The user has logged off the system. -

260004 The user name entered into the user display

already exists in the user administration.

Select another user name because user names have to

be unique in the user administration.

260005 The entry is rejected. Use a shorter user name.

260006 The entry is rejected. Use a shorter or longer password.

260007 The log-off time you entered is outside the valid

range of 0 to 60 minutes.

The entered value will be discarded and the original

value is retained.

Enter a value between 0 and 60 minutes for the logoff

time.

260008 An attempt was made to read a PTProRun.pwl file

created with ProTool V 6.0 in WinCC flexible.

Reading the file was interrupted due to

incompatibility of the format.

270000 A tag is not displayed in the alarm because it

attempts to access an invalid address in the PLC.

Check if the data area for the tag in the controller exists,

whether the configured address is correct and whether

the value range for the tag is correct.

270001 There is a unit-dependent limit as to how many

alarms may be queued simultaneously in order to

be displayed (see GHB). This limit has been

exceeded.

The display no longer contains all the alarms.

However, all the alarms are recorded in the alarm

buffer.

270002 Alarms are displayed from a log for which there is

no data in the current project.

Placeholders are issued for the alarms.

Delete older log data, if necessary.

270003 The service cannot be set up because too many

devices want to set up this service.

A maximum of four devices may execute this

action.

Connect fewer HMI devices which want to use the

service.

280000 Connection is reestablished because the cause of

the interruption has been eliminated.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-21

Number Effect/cause Remedy

280001 No additional data is read or written. Possible

causes:

• The cable is defective.

• The PLC does not respond, is defective, etc.

• Connection has been established via the wrong

interface.

• The system is overloaded.

Check if

• The cable is plugged in

• The PLC is OK

• The correct interface is used.

Reboot the system if the system alarm is displayed

continuously.

280002 A connection is used which requires a function

module in the PLC.

The function block has replied. Communication can

now proceed.

280003 A connection is used which requires a function

module in the PLC.

The function block has not replied.

Check if:

• The cable is plugged in

• The PLC is OK

• The correct interface is used.

Reboot the system if the system alarm is displayed

continuously.

The remedy depends on the error code:

1: The function block must set the COM bit in the

response container.

2: The function block must not set the ERROR bit in the

response container.

3: The function block must respond within the specified

time (timeout).

4: Establish an online connection to the controller.

280004 Connection to the PLC is interrupted. There is no

data exchange at present.

Check the connection parameters in WinCC flexible.

Check that the cable is plugged in, the PLC is operational

and the correct interface is used.

Reboot the system if the system alarm is displayed

continuously.

290000 The recipe tag could not be read or written to. It is

assigned the start value.

The alarm can be entered in the alarm buffer for up

to four more failed tags, if necessary. After that, the

alarm number 290003 is issued.

Check in the configuration that the address has been set

up in the PLC.

290001 An attempt has been made to assign a value to a

recipe tag which is outside the value range

permitted for this type.

The alarm can be entered in the alarm buffer for up

to four more failed tags, if necessary. After that, the

alarm number 290004 is issued.

Observe the value range for the tag type.

290002 It is not possible to convert a value from a source

format to a target format.

The alarm can be entered in the alarm buffer for up

to four more failed recipe tags, if necessary. After

that, the alarm number 290005 is issued.

Check the value range or type of the tag.

290003 This alarm is issued when alarm number 290000 is

triggered more than five times.

In this case, no further individual alarms are

generated.

Check in the configuration that the tag addresses have

been set up in the PLC.

290004 This alarm is issued when alarm number 290001 is

triggered more than five times.

Observe the value range for the tag type.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-22 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

In this case, no further individual alarms are

generated.

290005 This alarm is issued when alarm number 290002 is

triggered more than five times.

In this case, no further individual alarms are

generated.

Check the value range or type of the tag.

290006 The threshold values configured for the tag have

been violated by values entered.

Observe the configured or current threshold value of the

tag.

290007 There is a difference between the source and target

structure of the recipe currently being processed.

The target structure contains an additional data

recipe tag which is not available in the source

structure.

The data recipe tag specified is assigned its start

value.

Insert the specified data recipe tag in the source

structure.

290008 There is a difference between the source and target

structure of the recipe currently being processed.

The source structure contains an additional data

recipe tag which is not available in the target

structure and therefore cannot be assigned.

The value is rejected.

Remove the specified data recipe tag in the specified

recipe from the project.

290010 The storage location configured for the recipe is not

permitted.

Possible causes:

Impermissible characters, write protected, data

medium full or does not exist.

Check the configured storage location.

290011 The data mailbox with the specified number does

not exist.

Check the source for the number (constant or tag value).

290012 The recipe with the specified number does not

exist.

Check the source for the number (constant or tag value).

290013 An attempt was made to save a data mailbox under

a data mailbox number which already exists.

The action is not executed.

The following remedies are available:

• Check the source for the number (constant or tag

value).

• First, delete the data mailbox.

• Change the "Overwrite" function parameter.

290014 The file specified to be imported could not be

found.

Check the following:

• Check the file name.

• Ensure that the file is in the specified directory.

290020 Acknowledgment that downloading of data

mailboxes from HMI device to controller has

started.

290021 Acknowledgment that downloading of data

mailboxes from HMI device to controller was

completed without errors.

290022 Acknowledgment that downloading of data

mailboxes from HMI device to controller was

aborted due to an error.

Check the configuration:

• Are the tag addresses configured in the PLC?

• Does the recipe number exist?

• Does the data record number exist?

• The "Overwrite" function parameter set?

290023 Acknowledgment that downloading of data -

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-23

Number Effect/cause Remedy

mailboxes from the controller to the HMI device has

started.

290024 Acknowledgment that downloading data mailboxes

from the controller to the HMI device was

completed without errors.

290025 Acknowledgment that downloading of data

mailboxes from the controller to the HMI device

was aborted due to an error.

Check the configuration:

• Are the tag addresses configured in the PLC?

• Does the recipe number exist?

• Does the data record number exist?

• The "Overwrite" function parameter set?

290026 An attempt has been made to read/write a data

mailbox although the data mailbox is not free at

present.

This error may occur in the case of recipes for

which downloading with synchronization has been

configured.

Set the data mailbox status to zero.

290027 No connection to the PLC can be established at

present. As a result, the data mailbox can neither

be read nor written to.

Possible causes:

No physical connection to the controller (no cable

plugged in, cable is defect) or the controller is

switched off.

Check the connection to the PLC.

290030 This alarm is issued after reselecting a screen that

contains a recipe display in which a data mailbox is

already selected.

Reload the data mailbox from the storage location or

retain the current values.

290031 While saving, it was detected that a data mailbox

with the specified number already exists.

Overwrite the data mailbox or cancel the action.

290032 While exporting data mailboxes, it was detected

that a file with the specified name already exists.

Overwrite the file or cancel the process.

290033 Confirmation request before deleting data

mailboxes.

290040 A data mailbox error with error code %1 that cannot

be described in more detail occurred.

The action is canceled.

It is possible that the data mailbox was not installed

correctly on the controller.

Check the storage location, the data mailbox, the "Data

mailbox" area pointer and, if necessary, the connection to

the controller.

Wait a short period of time and then trigger the action

again.

If the error persists, contact Customer Support. Provide

them with the error code.

290041 A data mailbox or file cannot be saved because the

storage location is full.

Delete files no longer required.

290042 An attempt was made to execute several recipe

actions simultaneously. The last action was not

executed.

Wait a short period of time and then trigger the action

again.

290043 Confirmation request before storing data

mailboxes.

290044 The data store for the recipe has been destroyed

and will be deleted.

290050 Acknowledgment that the export of data mailboxes

has started.

290051 Acknowledgment that the export of data mailboxes -

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-24 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

was completed successfully.

290052 Acknowledgment that the export of data mailboxes

was aborted due to errors.

Ensure that the structure of the data mailboxes at the

storage location and the current recipe structure on the

HMI device are identical.

290053 Acknowledgment that the import of data mailboxes

has started.

290054 Acknowledgment that the import of data mailboxes

was completed successfully.

290055 Acknowledgment that the import of data mailboxes

was aborted due to errors.

Ensure that the structure of the data mailboxes at the

storage location and the current recipe structure on the

HMI device are identical.

290056 The value in the specified line/column could not be

read/written without errors.

The action was canceled.

Check the specified line/column.

290057 The tags of the specified recipe were switched from

operating mode "offline" to "online".

Each modification of a tag in this recipe is now

immediately transferred to the PLC.

290058 The tags of the specified recipe were switched from

operating mode "online" to "offline".

Modifications to tags in this recipe are no longer

immediately transferred to the PLC but must be

transferred there specifically if necessary by

downloading a data mailbox.

290059 Acknowledgment that the specified data mailbox

was stored successfully.

290060 Acknowledgment that the data mailbox memory

was cleared successfully.

290061 Acknowledgment that clearing the data mailbox

memory was aborted due to errors.

290062 The data mailbox number is above the maximum of

65536.

This data mailbox cannot be created.

Select another number.

290063 This occurs with the system function

"ExportDataRecords" when the parameter

"Overwrite" is set to No.

An attempt has been made to save a recipe with a

file name that already exists.

The export is canceled.

Check the system function "ExportDataRecords".

290068 Request to confirm whether all data mailboxes in

the recipe should be deleted.

290069 Request to confirm whether all data mailboxes of all

recipes should really be deleted.

290070 The data mailbox specified is not in the import file. Check the source of the data mailbox number or data

mailbox name (constant or tag value).

290071 During the editing of data mailbox values, a value

was entered that was below the lower limit of the

recipe tag.

The entry is rejected.

Enter a value within the limits of the recipe tag.

290072 During the editing of data mailbox values, a value

was entered that was above the upper limit of the

Enter a value within the limits of the recipe tag.

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 A-25

Number Effect/cause Remedy

recipe tag.

The entry is rejected.

290073 An action (e.g. saving a data mailbox) was not

possible due to an unknown reason.

The error corresponds to the status alarm

IDS_OUT_CMD_EXE_ERR in the large recipe

view.

290074 While saving, it was detected that a data mailbox

with the specified number already exists but under

another name.

Overwrite the data mailbox, change the data mailbox

number, or cancel the action.

290075 A data record with this name already exists.

Saving the data record is stopped.

Select a different data record name.

300000 Process monitoring (e.g. using PDiag or S7-Graph)

has been incorrectly programmed. More alarms are

queued than allowed by the specifications of the

CPU. No further ALARM_S alarms can be

managed by the PLC and reported to HMI devices.

Change the PLC configuration.

300001 Logon cannot be performed for ALARM_S on this

PLC.

Select a PLC that supports the ALARM_S service.

310000 An attempt is being made to print too many reports

simultaneously.

Since only one report can be printed at a time, the

print job is rejected.

Wait until the printout of the previous active report has

finished.

Repeat the print job if necessary.

310001 An error occurred on triggering the printer. The

report is either not printed or printed with errors.

Evaluate the additional system alarms generated for this

alarm.

Repeat the print job if necessary.

320000 The movements have already been indicated by

another device.

The movements can no longer be controlled.

Select the movements on the other display units and

select the movement screen on the required display unit.

320001 The network is too complex.

The defective operands cannot be displayed.

Display the network in STL.

320002 No diagnostics-capable alarm have been selected.

The units related to the alarm could not be

selected.

Select a diagnostics-capable alarm in the screen

ZP_ALARM.

320003 No alarms exist in respect to the selected unit. No

network can be displayed in the detail display.

Select the defective unit in the general view screen.

320004 The required signal statuses could not be read by

the PLC. The defective operands cannot be

determined.

Check the consistency between the configuration on the

display unit and the PLC program loaded.

320005 The project contains ProAgent partitions which are

not installed. No ProAgent diagnostics can be

performed.

In order to run the project, install the ProAgent option

packet.

320006 You have attempted to execute a function that is

not possible with the current configuration.

Check the type of the selected unit.

320007 No operands causing a fault have been found in the

networks.

ProAgent cannot display any blocked operands.

Switch the Detail Screen to STL display mode and check

the status of the operands and exclusion operands.

320008 The diagnostic data saved in the configuration is

not synchronized with that in the PLC.

ProAgent can only display the diagnostic units.

Recompile the project and download it to the HMI device

again.

320009 The diagnostic data saved in the configuration is Recompile the project and download it to the HMI device

Appendix

A.2 System alarms

MP 370 (WinCC flexible)

A-26 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Number Effect/cause Remedy

not fully synchronized with that in the PLC. The

diagnostic screens can be operated normally.

ProAgent may be unable to display all diagnostic

texts.

again.

320010 The diagnostic texts saved in the configuration are

not synchronized with that in the STEP7.

The ProAgent diagnostics data is not up-to-date.

Recompile the project and download it to the HMI device

again.

320011 There is no unit with the referenced DB number

and FB number.

The function cannot be executed.

Check the parameters of function "SelectUnit" and the

units selected in the project.

320012 The "Step sequence mode" dialog box is no longer

supported.

Use Step Sequence Screen ZP_STEP from the

appropriate standard project for your project. Instead of

calling function Overview_Step_Sequence_Mode, call the

function "FixedScreenSelection" using ZP_STEP as the

screen name.

320014 The selected PLC cannot be evaluated for

ProAgent.

The alarm view configured with the system function

"EvaluateAlarmDisplayFault" could not be found.

Check the parameters of the system function

"EvaluateAlarmDisplayFault".

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 B-1

Abbreviations B

CPU Central Processing Unit

CSV Comma Separated Values

CTS Clear To Send

DC Direct Current

DCD Data Carrier Detect

DIL Dual-in-Line (electronic chip housing design)

DP Decentralized Periphery

DSN Data Source Name

DSR Data Set Ready

DTR Data Terminal Ready

ESD Electrostatically Sensitive Devices

EMC Electromagnetic Compatibility

EN European Norm

ES Engineering System

ESD Electrostatic Sensitive Device

GND Ground

RF High Frequency

HMI Human Machine Interface

IEC International Electronic Commission

IF Interface

LED Light Emitting Diode

MMC Multi Media Card

MOS Metal Oxide Semiconductor

MPI Multipoint Interface (SIMATIC S7)

MS Microsoft

MTBF Mean Time Between Failures

N.C. Not connected

OP Operator Panel

PC Personal Computer

PG Programming Unit

PPI Point to Point Interface (SIMATIC S7)

RAM Random Access Memory

RTS Request To Send

RxD Receive Data

SELV Safety Extra Low Voltage

SP Service Pack

PLC Programmable Logic Controller

Abbreviations

MP 370 (WinCC flexible)

B-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

STN Super Twisted Nematic

Sub-D Subminiature D (plug connector)

TAB Tabulator

TCP/IP Transmission Control Protocol/Internet Protocol

TFT Thin Film Transistor

TxD Transmit Data

UL Underwriter’s Laboratory

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 C-1

Glossary C

Display duration

Defines whether and how long a system alarm is displayed on the HMI device.

A PLC in the SIMATIC S5 series, e.g. the AG S5-115U

A PLC in the SIMATIC S7 series, the SIMATIC S7-300 for example

AS 511

The protocol of the programming unit interface to the PLC SIMATIC S5

Operating element

Is a component part of a project to enter values and trigger functions. A button, for example,

is an operating element.

Screen

A screen displays all the logically related process data on the HMI device. The display of the

process data can be supported by graphic objects.

Screen object

Is a configured object for displaying or operating the system being monitored, e.g. a

rectangle, an I/O field or Recipe View.

Bootloader

Used to start up the operating systems and is automatically started when the HMI device is

switched on. A start graphic is displayed during startup. Once the operating system is

loaded, the loader or the Control Panel is displayed, depending on the HMI device.

Booting

Also refer to Starting

Glossary

MP 370 (WinCC flexible)

C-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

I/O field

The I/O field enables values to be entered or output on the HMI device which are then

transferred to the PLC.

Event

Functions are triggered by the arrival of defined events. Events can be configured. Events

which can be configured for a button include 'press button' and 'release button'.

Field

An area reserved in configured screens for entering input and output values.

Flash memory

Is a memory with non-volatile memory chips which is used as a mobile storage medium in

the form of a memory card or installed permanently on the main board. The mobile storage

medium market is determined by Flash memories; Compact Flash and Smart Media are

predominant.

Compact Flash and Smart Media differ in their basic, inner design. In the case of CF cards,

the control electronics is in the card whereby, with SM cards, the control electronics is

installed in the associated device.

Function

A function is linked to an icon in the Control Panel or an operating element in the project.

Softkey

Is a key on the HMI device which can be configured as required. A function is assigned to

the key during the configuration. The assignment of the function keys may be dependent on

the screen being displayed or independent of the screen displayed.

Half brightness life

Time period after which the brightness of the lighting tube only achieves 50% of its original

value, for example. The specified value depends on the operating temperature.

Hardcopy

Represents a printout of the current screen content on a connected printer.

Help text

Configurable information on objects in a project. The help text for an alarm can, for example,

contain information on the cause of the fault and methods of elimination.

Glossary

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 C-3

Image

A file which can be transferred from the configuration computer to the HMI device. The

Image contains the operating system for the HMI device and parts of WinCC flexible runtime

required to run a project.

Alarm logging

Is the printout of user-defined alarms parallel to output on the HMI device screen.

Alarm, user-defined

A user defined alarm can be assigned to one of the following alarm classes:

• Error

• Operation

• User-defined alarm classes

A user-defined alarm makes reference to a certain operating status of the system being

monitors which is connected to the HMI device via the PLC.

Alarm, departing

Moment at which the triggering of an alarm by the PLC is reset.

Alarm, arriving

Moment at which an alarm is triggered by the PLC or HMI device.

Alarm, acknowledging

Acknowledgement of an alarm confirms that it has been noted.

Conventions

A system of characters, symbols and rules governing language syntax; in data processing

they define the syntax of the programming language.

Object

Is a component part of a project, e.g. a screen or alarm. Objects serve to display or enter

texts and values on the HMI device.

Project

The result of a configuration using a configuration software. The project contains system-

specific objects, basic settings and alarms in the form of screens. The project is saved in the

project file with the file name extension *.hmi if it has been configured with WinCC flexible.

It is necessary to distinguish between the project on the configuration computer and that on

an HMI device. A project on the configuration computer can be available in several

Glossary

MP 370 (WinCC flexible)

C-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

languages than can be managed on the HMI device. The project on the configuration

computer can be set up for different HMI devices. Only the project set up for a particular HMI

device can be transferred to that HMI device.

Project file

Is the compiled file which is created after the configuration from a source file for a specific

HMI device. The project file is transferred to the associated HMI device and serves for

operating and monitoring the system to be monitored. Refer to Source file.

Configuration computer

The general term for programming units and PCs on which projects are created, using a

configuration software, for use monitoring a system.

Configuration software

Is a software to create projects which serves for process visualization – also refer to project,

process visualization and runtime software.

Process visualization

Is the representation of processes from the areas of production, logistics and services using

texts and graphics. Configured elements enable the data to be read from and written to

processes running on systems being monitored and, thus, to actively intervene in them.

Source file

Is the file from which various project files can be created, depending on the configuration.

The source file is not transferred and remains on the configuration computer.

The file extension of a source file is *.hmi. Refer to Source file, compressed and Project file.

Source file, compressed

Is the compressed form of the source file. It can be transferred, in addition to the project file,

to the associated HMI device. "Enable BackTransfer" must be activated in the project on the

configuration computer. The file extension of a compressed source file is *.pdz. The standard

memory location for a compressed source file is the external memory card. Refer to Source

file.

To restore a source file, it is necessary to use the same WinCC flexible version which was

used to configure the project.

Remote on/off

Is an option in the "Loader" menu which enables and disables remote control of the HMI

device from the PLC.

Glossary

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 C-5

Recipe

A combination of tags to a fixed data structure. The data structure configured can be

assigned data on the HMI device and is then referred to as a data record. The use of recipes

ensures that when a data record is downloaded, all the assigned data is transferred to the

PLC at the same time.

Runtime

Instantiation for a project on an HMI device. Refer to project file.

Runtime software

Is a software for process visualization with which a project on a configuration computer can

be tested – also refer to project and configuration software.

Acknowledge

Acknowledgement of an alarm confirms that it has been noted.

STEP 7

Programming software for SIMATIC S7, SIMATIC C7 and SIMATIC WinAC.

Start

A project can be called in by means of a button in the Loader. This procedure is referred to

as "starting".

PLC

Is a general term for devices and systems with which the HMI device communicates, e.g.

SIMATIC S7.

Job mailbox

This triggers a function via the PLC.

Fault time

This relates to the time interval between the arrival and departure of an alarm.

Symbolic I/O field

Is a field for the input/output of a parameter. I.e. it contains a list of predefined entries from

which one can be selected.

Glossary

MP 370 (WinCC flexible)

C-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

System, to be monitored

A general term for machines, processing centers, systems and plants as well as processes

which are to be operated and observed by an HMI device.

System alarms

Assigned to the "System" alarm class. A system alarm makes reference to internal states in

the HMI device and the PLC.

Tab order

Is defined during the configuration to set the sequence in which objects are focused on

pressing the <TAB> key.

Transfer

The transfer of a run-capable project to the HMI device.

Transfer mode

Is an operating mode on the HMI device used for transferring a run-capable project from the

configuration computer to the HMI device. Refer to Transfer mode.

Transfer mode

Activates transfer mode. Setting the HMI device to transfer mode is a condition for

transferring data from the configuration computer to the HMI device and vice versa. A logical

connection via the data line does not exist. Refer to Transfer mode.

Bootstrapping

An option for updating the operating system. When a functional operating system is

available, updating can be carried out without booting. Otherwise, updating with booting is

necessary. In this case, the configuration computer communicates with the HMI device via

the bootloader.

Tag

Is a defined memory location in which values can be written to and read from. This can be

done from the PLC or via the HMI device. Depending on whether the tags have a connection

to the PLC or not determines the difference between "external" tags (process tags) and

"internal" tags.

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 Index-1

Index

ACK

Key, 9-8

Acknowledge

Key, 9-8

acknowledgement

Acoustic, 1-5, 6-17, 9-3, 12-6

visual, 9-3

with touch control, 9-3

Acknowledgement groups, 1-6

Acoustic acknowledgement, 1-5, 6-17, 9-3, 12-6

Additional applications, 6-15

Memory requirements, 6-15

Air discharge, 12-7

Alarm acquisition, 1-6

Alarm buffer, 1-6

in Runtime, 8-2

Alarm events, 1-6

Alarm indicator

Behavior, 9-22

in Runtime, 8-3

Purpose, 9-22

Alarm log

in Runtime, 8-2

Scope of alarm logging, 8-4

Alarm logging, 1-6

Alarm protocol, 8-2, 8-8

Alarm view

in Runtime, 8-2

Layout, 9-23

Operator controls, 9-24

Purpose, 9-23

Alarm window

in Runtime, 8-3

ALARM_S, 1-6

Alarms

Functional scope, 1-5

in Runtime, 8-2

Alignment

Printer, 6-11

Alphanumeric key assignment, 9-8

Alphanumeric keys, 5-6

Alphanumeric screen keyboard, 9-5

ALT

Key, 9-9

Alt layer

Screen keyboard, 9-6

Ambient conditions, 12-7

Angle of inclination, 3-4, 12-7

application

In industrial sector, 2-1

In residential areas, 2-2

Approvals, A-1, A-2

Area

Printer, 6-11

Area of use, 1-2

ASCII character set

Printer, 4-8

Authorization, iv

Back transfer, 7-21

in Runtime, 8-7

Transfer, 7-21

Back transfer, 7-10

Execute, 7-11

Requirements, 7-11

Back-lighting

Screen, 1-5, 12-5

Switch off, 6-14

Backspace

Key, 9-8

Backup, 7-15, 12-6

Backup battery, 1-9, 4-4, 12-6

Changing, 11-2

Bar

Layout, 9-34

Operation, 9-34

Purpose, 9-34

Barometric pressure, 12-7

Battery, 1-9, 12-6

Changing, 11-2

Battery connection, 4-4

Baud rate

Printer, 6-11

Transfer mode, 7-5

Index

MP 370 (WinCC flexible)

Index-2 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Behavior

Alarm indicator, 9-22

I/O field, 9-16

Icon, 9-54

Recipe view with screen change, 9-28

Simple recipe view, 9-32

Sm@rtClient view, 9-51

Brightness

Set, 6-7, 9-10

Bulk storage, 1-10, 12-5

Burst interference, 12-8

Button

Layout, 9-13

Purpose, 9-13

Button action feedback, 9-3

Cable cross-section, 4-15

Cables, 3-2

Calibration

Touch screen, 6-8

Calling

Operator note: Touch panel unit, 9-5

Operator note:keyboard device, 9-11

Operator note:screen keyboard, 9-5

Operator note:System function, 9-7

Operator note:touch panel, 9-5, 9-6

Remote control, 9-51

Remote monitoring, 9-51

Cancel

Key, 9-8

Capacity

Alarm buffer, 1-6

Backup battery, 12-6

Memory, 1-5

CE approval, A-1

Certificate

ESD, A-2

CF card, 1-10

Changing

Battery, 11-2

Language, 7-12

Character set

Printer, 4-8

Cleaning

Device, 11-1

Cleaning agents, 11-1

Clock

Internal, 1-9

Operation, 9-43

Purpose, 9-43

Dialog, 9-11

Color display, 1-5, 12-5

Colors, 1-5, 12-5

Combo box

Open, 9-9

Commissioning for the first time, 7-1

Communication, 1-8

PLCs from other manufacturers, 1-9

SIMATIC PLCs, 1-8

Communication options, 4-5

Compact Flash Card, 1-11, 12-5

Compatibility conflict, 7-2, 7-3

Compressing

PU functions, 4-12

Conditions for use, 3-2

Conduction

RF, 12-8

Configuration, 10-6

Memory location, 7-7

Of recipes, 10-6

Source file, 7-7

Configuration computer

Connecting, 4-13

Configuration phase, 1-4

Configuration software, 1-3, 1-5

Configuring

Interface IF1B, 4-11

Conflict

Compatibility, 7-2, 7-3

Connecting

Configuration computer, 4-13

External keyboard, 4-9

HMI device, 4-4

Mouse, 4-9

PLC, 4-11

Power supply, 4-15

Printer, 4-7

UPS, 4-14

Connection

Electrical, 4-4

Order, 4-4

To configuration computer, 4-13

To external keyboard, 4-9

To mouse, 4-9

To PLC, 4-11

To printer:, 4-7

Contact discharge, 12-7

Control keys, 5-5

Control mode

Remote control, 9-52

Sm@rtClient view, 9-52

Conversion functions, 1-7

Index

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 Index-3

Copy

Recipe data record in Runtime, 10-15

create

Recipe record on the HMI device, 10-15

Create

Labeling strips, 5-8

Cross-section

Power supply cable, 4-15

CSV file, 10-5

C-Tick, A-1

CTRL

Key, 9-9

Cursor

Key, 5-6, 9-8

Cut-out

Installation, 12-5

Data

Technical, 12-5

Data log

in Runtime, 8-5

Data loss, 7-16

Data mailbox

For recipes, 10-8

Data record

exporting, 10-18

importing, 10-18

reading, 10-17

Transfer, 10-17

Date, 6-5, 7-2

Date / time field

Behavior, 9-41

Keyboard control, 9-41, 9-42

Layout, 9-41

Mouse control, 9-42

Purpose, 9-41

Touch control, 9-41

Date and time

synchronizing, 6-5

Default setting

Printer, 6-12

Degree of protection, 1-2, 3-3, 12-5

Delete

Key, 9-8

deleting

Recipe data record in Runtime, 10-16

Depth

Installation, 12-5

Device data

Displaying, 6-10

Dialog

Closing, 9-11

Dim back-lighting

Screen, 6-13

Dimensions, 12-5

MP 370 12" Key, 12-4

MP 370 12" Touch, 12-1

MP 370 15" Touch, 12-3

Directives

EEC, 12-7

ESD, A-2

DirectKey, 9-2

Discharge

Static, 12-7

Display, 1-5

Set brightness, 6-7

DNS server, 6-18

Editing, 10-5

Recipe data record in WinCC flexible, 10-5

Recipe record, 10-5

Electrostatic discharge

Precautions, A-2

EMC directives, 3-1

END

Key, 9-8

Enter

Key, 9-8

ENTER

Key, 9-8

ESC

Key, 9-8

ESC/P compatibility, 4-7

ESD, A-2

Handling, A-3

Measuring, A-3

Shipping, A-3

Ethernet, 6-17

Ethernet interface, 4-4

Assignment, 12-10

Ex Zone 2/22, A-1

Example

Network functions, 6-21

Exchange

Labeling strips, 5-7

exporting

Recipe, 10-18

Recipe record, 10-18

User data, 8-8

Extend

Memory, 1-10

Index

MP 370 (WinCC flexible)

Index-4 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

External dimensions, 12-5

External keyboard

Connecting, 4-9

Operation, 5-9

Features

MP 370, 1-5

Multi Panels, 1-1

Flashing

LED, 5-4

FM approval, A-2

Foil

Labeling strips, 5-8

Forcing

Permissions in remote operation, 9-52

Format

Paper, 6-11

Front panel

Thickness, 3-3, 3-4

Front view

MP 370 12" Key, 12-4

MP 370 12" Touch, 12-1

MP 370 15" Touch, 12-3

Function keys, 1-5, 5-2

LED, 5-4

Functional scope, 1-5

Gauge

Layout, 9-40

Operation, 9-40

Purpose, 9-40

General operation

Keyboard unit, 9-7

Touch panel unit, 9-2

Global softkey, 5-4

Graphic I/O field

Purpose, 9-18

Ground connection, 4-4, 4-6

Grounding, 4-6

Grounding screw, 4-6

Group acknowledgement, 1-6, 9-8

Hardware options, 1-9

Hazardous location, A-1

Help text, 1-7

Calling:keyboard device, 9-11

calling:screen keyboard, 9-5

Calling:system function, 9-7

Calling:Touch panel, 9-5, 9-6

viewing (key), 9-8

Hide

Screen keyboard, 9-5

High frequency radiation, 2-1

HMI device

Connecting, 4-4

Name in the network, 6-5

Recommissioning, 7-3

remote control, 9-51

remote monitoring, 9-51

Transfer mode, 7-3

HOME

Key, 9-8

Housing, 12-5

I/O field

Behavior, 9-16

Keyboard control, 9-17

Layout, 9-16

Mouse control, 9-17

Purpose, 9-16

Touch control, 9-16

Icon, 5-4

Behavior, 9-54

Purpose, 9-54

Immunity to interference

EMC directives, 3-1

importing

Recipe, 10-18

Recipe record, 10-18

User data, 8-8

Increase

Brightness, 6-7

Indicators, 12-5

information

General, 2-1

Safety, 2-1

Input

Alphanumeric values:touch panel, 9-5

Numeric values:touch panel, 9-5

Input of alphanumeric values

Touch panel unit, 9-5

Input of numeric values

Touch panel unit, 9-5

Index

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 Index-5

Installation

Configuration computer, 4-13

External keyboard, 4-9

in 19 inch cabinets, 4-1

Keyboard unit, 4-1

Mechanical, 4-1

Mouse, 4-9

PLC, 4-11

Printer, 4-7

Touch panel unit, 4-2

Installation conditions, 3-3

Installation cut-out, 12-5

Keyboard unit, 3-4

MP 370 12 inch touch panel unit, 3-4

MP 370 15 inch touch panel unit, 3-4

Installation depth, 12-5

Installation dimensions

19 inch cabinets, 4-1

Installation location, 1-2, 3-3

Installation position, 12-7

Interface assignments, 12-8

Interface IF1A

Assignment, 12-8

Interface IF1B

Assignment, 12-9

Interface IF2

Assignment, 12-9

Interfaces, 1-5

Configure 1F1B, 4-11

IF1A, 4-11

IF1B, 4-11

IF2, 4-13

Internet Explorer, 1-12

Irradiation

RF, 12-7

Key pads, 5-2

Keyboard, 1-5, 12-6

Connecting, 4-9

Keyboard control

Date / time field, 9-41, 9-42

I/O field, 9-17

Keyboard layers, 9-6

Keys

Remote control, 9-53

Labeling

Softkey, 5-6

Labeling strips, 4-1

Exchange, 5-7

printing, 5-8

Template file, 5-8

Landscape format

Printer, 6-11

Language

Set, 7-12

Language switching, 1-8, 7-12, 9-1

Layout

Alarm view, 9-23

Bar, 9-34

Button, 9-13

Gauge, 9-40

I/O field, 9-16

Recipe view, 9-28

Simple alarm view, 9-26

Simple recipe view, 9-31

Simple user view, 9-46

Slider control, 9-38

Sm@rtClient view, 9-51

Status force, 9-48

Switch, 9-14

Trend view, 9-35

User view, 9-44

LCD type, 12-5

LED control, 5-4, 8-9

Length

Alarm text, 1-6

Light emitting diode

Acknowledge, 9-8

Help text, 9-8

Softkey, 5-4

Toggle, 9-8

Limit value monitoring, 1-7

Lines, 3-2

Literature, 1-5

Lithium battery, 12-6

Warning, 11-3

Load

Project data, 7-1

Recipe data record in Runtime, 10-15

Loader, 6-1

Password protection, 6-2

Local function keys, 5-4

Log

in Runtime, 8-3

Memory options, 8-4

Logging, 1-7

Scope of alarm logging, 8-4

Log-off time

exporting/importing, 8-8

in Runtime, 8-8

Index

MP 370 (WinCC flexible)

Index-6 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Maintenance, 11-1

Manual transfer, 7-3

Margin

Printer, 6-12

Mechanical installation, 4-1

Membrane keyboard, 1-5, 12-6

Memory, 1-5

Memory card, 1-10

Memory extension, 1-5

Memory location

Project file, 7-7

Menu bar

Enable, 9-11

Modal dialogs, 7-4

Mode

Printer, 6-11

modify

Recipe data record in Runtime, 10-15

Modifying recipe structures, 10-19

Monitoring mode

Sm@rtClient view, 9-52

Mouse

Connecting, 4-9

Operation, 5-9

Mouse control

Date / time field, 9-42

I/O field, 9-17

Mouse pointer, 5-9

MPI address

Transfer mode, 7-5

MPI transfer, 7-6

Multi Panels, 1-1

Multifunctional platform, 1-1

Multiple key operation, 9-1

Navigating

Operating system, 9-10

Network connection, 12-7

Noise immunity, 12-7, 12-8

Norms, 12-7

Number

Alarms, 1-5

Colors (display), 12-5

Data records, 1-7

Fields per screen, 1-6

Graphics lists, 1-7

Languages, 1-8

Recipes, 1-7

Scripts, 1-8

Tags per screen, 1-6

Text lists, 1-7

User, 1-7

Numeric keyboard assignment, 9-8

Numeric screen keyboard, 9-5

OEM applications, 6-15

Memory requirements, 6-15

Offices, iii

Offline test, 7-9

Online test, 7-9

OPC, 1-8

Open

Combo box, 9-9

Tab, 9-11

Task Manager, 9-10

Windows CE Start menu, 9-10

Operating a keyboard device, 9-7

Operating mode

Changing, 7-13

Offline mode, 7-13

Online mode, 7-13

Transfer mode, 7-13

Operating mode switchover, 7-9

Operating recipes

Copying a recipe data record, 10-15

Creating recipe records, 10-15

Data record transfer, 10-17

Delete recipe data record, 10-16

Exporting data records, 10-18

Import a data record, 10-18

Load recipe data record, 10-15

Modify recipe record, 10-15

Modifying the recipe structure, 10-19

Read recipe data record, 10-17

Synchronizing recipe tags, 10-16

Operating system, 1-1, 1-5, 12-5

Navigation, 9-10

Updating, 7-18

Operating the touch panel (TP), 9-2

Index

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 Index-7

Operation

Bar, 9-34

Clock, 9-43

Gauge, 9-40

Keyboard unit, 9-7

Touch objects, 9-2

Touch panel unit, 9-2

Operator controls

Alarm view, 9-24

Recipe view, 9-29

Simple alarm view, 9-27

Simple recipe view, 9-32

Status force, 9-49

Trend view, 9-35

Optimization

Brightness, 6-7

Option

Back transfer, 7-23

Transfer, 7-22

Options

Backup battery, 1-9

CF card, 1-10

Memory card, 1-10

PC card, 1-10

Order

The connections, 4-4

Overheating, 3-4

Overview, 1-1, 1-5

Page margin

Printer, 6-12

Paper size, 6-11

Password

exporting/importing, 8-8

in Runtime, 8-7

Path specification

Project file, 7-7

Connecting, 4-13

PC card, 1-10, 1-11, 12-5

PCL compatibility, 4-8

PE connection, 4-4

Permission

forcing (remote operation), 9-52

Connecting, 4-13

PG interface, 4-11

Pin assignment, 12-8

Pin plug connector, 4-15

Plan view

MP 370 12" Key, 12-4

MP 370 12" Touch, 12-1

MP 370 15" Touch, 12-3

PLC

Connecting, 4-11

Plug connections, 3-2

Plug-in terminal block, 4-15

Port

Printer, 6-11

Portrait format

Printer, 6-11

Power cables, 3-2

Power consumption, 12-6

Power supply, 4-4, 4-15, 12-6

Print functions, 1-7

Print quality

Set, 6-11

Printer

Connecting, 4-7

Set, 6-10

printing

Report, 8-5

Runtime, 8-8

Screen, 8-8

Process running phase, 1-4

Processor type, 1-5, 12-5

Product category, 1-1

PROFIBUS DP, 4-11

Profiles, 4-1

Programming voltage, 1-11

Project

Back transfer, 7-10

Replace, 7-3

Test, 7-9

Test offline, 7-9

Test online, 7-10

Project data

Load, 7-1

ProSave, 7-14

Backup, 7-15

Integrated, 7-14

Restore, 7-17

Stand-alone, 7-14

PU functions, 1-8

Pulse modulation, 12-7

Index

MP 370 (WinCC flexible)

Index-8 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Purpose

Alarm indicator, 9-22

Alarm view, 9-23

Bar, 9-34

Button, 9-13

Clock, 9-43

Gauge, 9-40

I/O field, 9-16

Icon, 9-54

Recipe view, 9-28

Simple alarm view, 9-25

Simple recipe view, 9-31

Simple user view, 9-46

Slider control, 9-38

Sm@rtClient view, 9-51

Status force, 9-48

Switch, 9-14

Trend view, 9-35

Quality

Graphic printing, 6-11

Radio interference, 12-8

Radio interference level, 12-8

Rated voltage, 12-6

Recipe, 10-3, 10-4

Basic principles, 10-3

Configuration options, 10-6

Configuration settings, 10-6

Data record, 10-4

Design, 10-3

Display in Runtime, 10-1, 10-12

exporting, 10-18

importing, 10-18

Recipe record, 10-4

Copy, 10-15

Create on the HMI device, 10-15

deleting, 10-16

Design, 10-3

Editing in WinCC flexible, 10-5

exporting, 10-18

importing, 10-18

Load, 10-15

modify, 10-15

synchronizing, 10-16

Transfer, 10-5

Transfer options, 10-5

Recipe screen, 10-13

Overview, 10-13

Recipe view, 10-12

Behavior with screen change, 9-28, 10-14

Layout, 9-28

Operation with function keys, 10-14

Operator controls, 9-29

Overview, 10-12

Purpose, 9-28

Recipes, 1-7

Recommissioning

HMI device, 7-3

Reduce

Brightness, 6-8

Regional setting, 6-13

Relative humidity, 12-7

Remote control

calling, 9-51

Forcing permission, 9-52

of HMI devices, 9-51

Stop, 9-52

Remote monitoring

calling, 9-51

of HMI devices, 9-51

Stop, 9-52

Report

in Runtime, 8-5

printing, 8-5

Representatives, iii

Resolution

Indicators, 1-5, 12-5

Restore, 7-16

Reverse poling protection, 4-15

RF conduction, 12-8

RF irradiation, 12-7

RJ45 plug, 12-10

RTS signal, 4-11

Runtime

Language switching, 9-1

Multiple key operation, 9-1

Operation, 9-1

Pictograms, 9-2

Runtime software, 7-7

Load, 7-1

Safety, 1-7

in Runtime, 8-7

Safety notes

High frequency radiation, 2-1

Work on the cabinet, 2-1

Scheduler, 1-8

Index

MP 370 (WinCC flexible)

Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0 Index-9

Screen, 12-5

printing, 8-8

Set brightness, 6-7, 9-10

Templates, 9-2

Screen change, 5-4

Screen diagonals, 1-5

Screen keyboard, 9-4

Alphanumeric, 9-5

Numeric, 9-5

Set, 6-6

Screen objects, 1-6

in Runtime, overview, 8-1

Screen objects in Runtime

Overview, 8-1

Screensaver, 6-13

Screw type clamps, 4-2

Scripts, 1-8

Scrolling back

Key, 9-8

Scrolling up

Key, 9-8

Seal, 3-3, 4-3

Securing, 4-1

Touch panel unit, 4-2

Selection

all, 9-10

Serial printer, 4-8

Service

In the Internet, iv

Service life

Backup battery, 11-2

Servicing, 11-1

Set up

Network, 6-17

Printer, 6-10

Settings

Brightness, 6-7, 9-10

Contrast, 6-7

Date/time, 6-5

Language, 7-12

Network, 6-6

Printer, 6-10

Regional, 6-13

Save, 6-9

Screen keyboard, 6-6

Touch calibration, 6-7, 6-8

Volume, 6-17

SHIFT

Key, 9-8

Shift layer

Screen keyboard, 9-6

Shift+Alt-Gr layer

Screen keyboard, 9-6

Shock loading, 12-7

Side view

MP 370 12" Key, 12-4

MP 370 12" Touch, 12-1

MP 370 15" Touch, 12-3

Signal lines, 3-2

Signal tone, 6-17

SIMATIC 500/505 DP, 1-8

SIMATIC 500/505 serial, 1-8

SIMATIC HMI HTTP Protocol, 1-8

SIMATIC S5 AS511, 1-8

SIMATIC S5 DP, 1-8

SIMATIC S7-200, 1-8

SIMATIC S7-300/400, 1-8

SIMATIC WinAC, 1-8

SIMOTION, 1-8

Simple alarm view

Layout, 9-26

Operator controls, 9-27

Purpose, 9-25

Simple recipe view

Behavior, 9-32

Layout, 9-31

Operator controls, 9-32

Purpose, 9-31

Simple user view

Layout, 9-46

Purpose, 9-46

Size

Paper, 6-11

Slider control

Layout, 9-38

Purpose, 9-38

Slot A, 1-10

Slot B, 1-10

Sm@rtClient view

Behavior, 9-51

Control mode, 9-52

Layout, 9-51

Monitoring mode, 9-52

Purpose, 9-51

Softkey, 5-4

Labeling, 5-6

Remote control, 9-53

Softkeys, 1-5

Software, 12-5

Software options, 1-12

Source file

Memory location, 7-7

Special characters

Key, 9-9

Stand-alone ProSave

Backup, 7-15

Standard cables, 4-13

Index

MP 370 (WinCC flexible)

Index-10 Operating Instructions, Edition 03/2004, 6AV6691-1DE01-0AB0

Standard layer

Screen keyboard, 9-6

Start screen, 7-2

Start up, 7-1

Static discharge, 12-7

Status force

Layout, 9-48

Operator controls, 9-49

Purpose, 9-48

Stop

Remote control and monitoring, 9-52

Storage location

Project file, 7-7

Runtime software, 7-7

Source file, 7-7

Sub-D plug, 12-9

Sub-D socket, 12-8, 12-9

Sunlight, 3-4

Supply source

Backup battery, 11-2

Support

In the Internet, iv

Surge coupling, 12-8

Switch

For 1F1B interface, 4-11

Layout, 9-14

Purpose, 9-14

Switch off

Back-lighting, 6-13

Power supply, 1-12

Switch settings

Interface IF1B, 4-11

Symbolic I/O field

Purpose, 9-20

Synchronization

With controller, 10-8

synchronizing, 6-5

Synchronizing

Recipe record, 10-16

Synchronizing recipe tags, 10-16

System alarms, A-4

Meaning, A-4

Parameters, A-4

System function, 10-5

to transfer of recipe data records, 10-5

System keys, 1-5, 5-3, 5-5

System settings, 6-2

TAB

Key, 9-8

Tabulator

Key, 9-8