153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S DESCRIPTION * * * 153.6 MHz SAW bandpass filter with 20 MHz bandwidth. 7 x 5 mm ceramic LCC package. RoHS compliant. TYPICAL PERFORMANCE Amp 10 dB/div Amp 1 dB/div Phase 5 deg/div Delay 100 ns/div Center = 153.6 MHz, 15 MHz/div (187.5 kHz incr) S11 (78.6-228.6 MHz) S22 (78.6-228.6 MHz) IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF0154BA03191S Rev A 28-Jul-2009 ECN 36477 Page 1 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S SPECIFICATION Parameter 1 Center Frequency, FC Minimum Insertion Loss Passband Ripple (143.6 to 163.6 MHz) Group Delay Deviation (143.6 to 153.6 MHz) Phase Ripple (143.6 to 153.6 MHz) Absolute Delay 2 1 dB bandwidth 2 Relative Attenuation (10 to 105 MHz) 2 Relative Attenuation (200 to 230 MHz) 2 Relative Attenuation (230 to 1000 MHz) Input Return Loss at Fc Output Return Loss at Fc Source and Load Impedance Temperature Coefficient of Frequency Ambient Temperature Notes: Min 20 50 52 40 10 10 - Typ 153.6 8.8 0.4 30 3.5 560 23.4 52 55 60 15 18 50 -86 25 Max 12 1 60 5 - Units MHz dB dB p-p ns p-p deg p-p ns MHz dB dB dB dB dB ohms ppm/C C - 1. Reference frequency. Computed as mean of the 3 dB frequencies. 2. All dB values are referenced to the insertion loss value. MAXIMUM RATINGS Parameter Storage Temperature Range Operating Temperature Range Input Power Level Min Max -40 -40 - 85 85 10 Units C C dBm MATCHING CIRCUIT 10 5 Input 50 Single ended Output 50 Single ended All other pads GND Ls1 = 138 nH Cp1 = 22 pF GND Ls2 = 207 nH Cp2 = 15 pF Notes: * Recommend 2% or better tolerance matching components. Typical inductor Q=40. * Optimum values may change depending on board layout. Values shown are intended as a guide only. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF0154BA03191S Rev A 28-Jul-2009 ECN 36477 Page 2 of 3 153.6 MHz SAW Filter 20 MHz Bandwidth Part Number SF0154BA03191S PACKAGE OUTLINE IDT BA03191S YYDDD Date Code (YY=year, DDD=day) Pad 1 indicator mark (ESD) Units: mm Tolerances are typically 0.15 mm except where indicated. Pad Configuration: Input: 10 Output: 5 Ground: All other pads SUGGESTED FOORPRINT Package Material: Body: Al2O3 ceramic Lid: Kovar, Ni plated Terminations: Au plating 1 m min, over a 1.3-8.9 m Ni plating 2.54 ISO 9001 Registered All specifications are believed to be accurate and reliable. However, MNC reserves the right to make changes without notice. (c) 2009 All rights reserved. IDT * SAW Products * 324 Clark Street, Worcester, MA 01606, USA * Ph 1-508-852-5400 * Fax 1-508-852-8456 www.idt.com DSSF0154BA03191S Rev A 28-Jul-2009 ECN 36477 Page 3 of 3