D12SP6FVQ - BANNER ENGINEERING

D12s are compact, totally self-contained visible-red ber optic sensors

for DIN rail mounting. D12 sensors are designed for use with Banner

glass and cut-to-length plastic ber optics. Standard D12FP and D12FV

plastic and glass ber optic sensors offer fast 0.5 millisecond (500 µs)

response. D12FVY Series (page 3) and D12FPY Series (page 4) sen-

sors have switch-selectable 50µs/500µs response modes for applications

that require a faster, high speed response time (50 µs as compared to the

500 µs of FP and FV models). D12FVY1 and D12FPY1 models have

switch-selectable response times along with a built-in 20 millisecond

pulse stretcher for use with loads (or input circuits) that are too slow to

react to quick sensing events when using the 50µs response mode.

All models operate from 10-30V dc. D12s are available with a choice

of NPN or PNP complementary outputs (one output normally open, one

output normally closed). The normally closed output of FP and FV models

(only) may be used as a diagnostic alarm output, depending upon the

hookup of the sensor to the power supply. All models are available with

either an attached cable or a 6" pigtail with a pico-type quick disconnect

connector. There is one D12 model line for glass bers, and another for

plastic bers. Model listings are given on pages 3 and 4.

Plastic ber models may be used with either the small diameter (.010" and

.020") or large diameter (.040") Banner cut-to-length plastic bers.

Two top-mounted LED indicators (see drawing, right) light to indicate

POWER ON and NORMALLY OPEN OUTPUT CONDUCTING condi-

tions.

On all D12 sensors operating in the 500µs (standard)

response mode, a red seven-segment moving-dot LED

bargraph (below) lights to indicate the relative strength

of the received light signal. This feature can greatly

simplify sensitivity adjustment and the task of ber

optic alignment, as well as provide a constant reference

over time for overall sensing system performance. In all

models and in both response modes, segment #1 of the

bargraph ashes to indicate an output overload. On all

sensors operating in the 500µs response mode, segment

#7 ashes to indicate marginal excess gain. On standard

(FP and FY) models, a ashing LED corresponds to the

"on" state of the D12's alarm output.

D12s have a 15-turn SENSITIVITY control, with a

slotted brass screw clutched at both ends of travel.

D12s are constructed of rugged black ABS (Cycolac®

KJB). The transparent housing cover is acrylic. All

D12 sensors are rated NEMA 2.

D12 Features

(top panel shown)

WARNING These photoelectric presence sensors do

NOT include the self-checking redundant circuitry necessary

to allow their use in personnel safety applications. A sensor

failure or malfunction can result in either an energized or a

de-energized sensor output condition.

Never use these products as sensing devices for personnel protection. Their

use as a safety device may create an unsafe condition which could lead to

serious injury or death.

Only MINI-SCREEN®, MULTI-SCREEN®, MICRO-SCREEN™,

MACHINE-GUARD™ and PERIMETER-GUARD™ Systems, and other

systems so designated, are designed to meet OSHA and ANSI machine safety

standards for point-of-operation guarding devices. No other Banner sensors

or controls are designed to meet these standards, and they must NOT be used

as sensing devices for personnel protection.

D12 plastic ber optic

sensor, mounted on a DIN

rail with a bifurcated

plastic ber optic assembly

attached.

D12 Series DIN Rail High Power Fiber Optic Sensors

• Fiber optic sensors for DIN rail mounting; cabled or QD

• Fast response: 500µs standard, 50µs for Y & Y1 models

• Visible red light source; models for use with either Banner glass

or plastic ber optic assemblies

• Choice of either NPN (sinking) or PNP (sourcing)

complementary outputs; 150 mA max. (continuous) load

• Normally closed output of most models may be wired as a diag-

nostic alarm output (depending upon hookup to power)

• Sensors operate from 10-30V dc.

• LED indicators for POWER ON and N.O. OUTPUT CON-

DUCTING

• 7-segment LED bargraph indicates received signal strength,

OUTPUT OVERLOAD, and MARGINAL EXCESS GAIN

*FPY, FPY1, FVY, and FVY1

models only. FP and FV models

operate in 500µs mode only.

Printed in USA 06/08 P/N 32822 rev E

Powerful self-contained sensors for use with glass or plastic ber optic assemblies

D12 Series DIN Rail Fiber Optic Sensors

Sourcing (PNP) Sourcing (PNP)

Standard Hookup Alarm Hookup

Hookup Diagrams, D12 Series Sensor

Sinking (NPN) Sinking (NPN)

Standard Hookup Alarm Hookup

Sensing range: see individual excess gain curves, pages 3 and 4.

Sensing beam: visible red, 680 nanometers.

Supply voltage: 10 to 30V dc at 45 mA max, exclusive of load.

Protected against reverse polarity and inductive load transients.

Output congurations:

Solid-state dc complementary outputs:

For glass ber optics (see page 3 for models)

D12SN6FV Series NPN sinking (standard)

D12SN6FVY Series NPN sinking (high speed)

D12SN6FVY1 Series NPN sinking (high speed, with pulse stretcher)

D12SP6FV Series PNP sourcing (standard)

D12SP6FVY Series PNP sourcing (high speed)

D12SP6FVY1 Series PNP sourcing (high speed, with pulse stretcher)

For plastic ber optics (see page 4 for models)

D12SN6FP Series NPN sinking (standard)

D12SN6FPY Series NPN sinking (high speed)

D12SN6FPY1 Series NPN sinking (high speed, with pulse stretcher)

D12SP6FP Series PNP sourcing (standard)

D12SP6FPY Series PNP sourcing (high speed)

D12SP6FPY1 Series PNP sourcing (high speed, with pulse stretcher)

The N.C. (normally closed) output of standard FP and FV models may

be used as an alarm output, depending upon the hookup to the power

supply.

Output rating: Complementary outputs, one normally open (N.O.)

and the other normally closed (N.C.). 150 mA maximum each output.

No false pulse on power-up. (False pulse protection circuit causes a 0.1

second delay on power-up.) Short-circuit protected.

Off-state leakage current <10 microamps at 30V dc.

On-state saturation voltage <1V at 10 mA dc; <1.5V at 150 mA dc.

The total load may not exceed 150 mA.

Response time (FV, FP models): .

500 microseconds "on"; 500 microseconds "off".

Repeatability is 130 microseconds.

FVY, FVY1, FPY, and FPY1 models have switch-selectable standard

500 microsecond response mode plus a high speed (50 microseconds

on/off) mode. Repeatability in the high-speed (50µs) mode is 15 mi-

croseconds. FPY1 and FVY1 models (when used in the 50µs response

mode) include a 20 ms pulse stretcher for use in applications in which

the load (or input circuit) requires a longer input signal.

Response time and repeatability are independent of signal strength.

Specications, D12 Series sensors

Indicators: Two top-mounted LED indicators, one yellow and one

green, and one seven segment red LED moving-dot bargraph. Note

that the seven segment bargraph and marginal excess gain indication

(bargraph segment #7) are inoperative in the 50µs response mode on

Y and Y1 models.

GREEN LED lights for DC POWER ON.

YELLOW LED lights for NORMALLY OPEN OUTPUT CONDUCT-

ING.

On all models in 500µs response mode, the 7-segment moving dot

red LED bargraph lights to indicate relative received light signal

strength. On all models in 50 and 500µs response modes, segment

#1 ashes to indicate OUTPUT OVERLOAD. On all models in the

500µs response mode, segment #7 ashes to indicate MARGINAL

EXCESS GAIN. On standard FV and FP models, a ashing LED

corresponds to the "on" state of the alarm output. (Alarm output not

available on Ys & Y1s.)

Adjustments: All models have a SENSITIVITY control on top of

module (15-turn slotted brass screw, clutched at both ends of adjust-

ment). FVY and FPY (high speed models) also have a top-mounted

response mode selector switch.

Construction: Black ABS (Cycolac® KJB) housing with acrylic

cover. Rated NEMA 2; IEC IP11. The ber clamping element is

Delrin®. Stainless steel M3 x 0,5 hardware for use with mounting

bracket (supplied).

Cable: 6-1/2-foot (2 m) or 30-foot (9 m) attached PVC-covered

cable, or 6-inch pigtail with pico-type 4-pin QD connector.

Mounting bracket: D12 Series sensors mount directly to a stan-

dard DIN rail, or may be through-hole mounted using the supplied

mounting bracket and M3 x 0,5 hardware. Bracket material is black

VALOX®.

Operating temperature range: -20° to +70°C (-5° to +158°F).

Maximum relative humidity 90% at 50°C (non-condensing).

Application caution...

D12 Series sensors are designed to deliver very high optical energy

(excess gain). They should not be used for applications which offer

low optical contrast (i.e. only a small difference in received light levels

between the light and dark sensing conditions). Examples include diffuse

mode sensing of objects in front of a reective background and opposed

mode sensing of non-opaque materials.

D12 sensors excel in applications requiring high excess gain (e.g. for

long-range sensing, sensing with long ber lengths, diffuse sensing of

materials with low reectivity, etc.)

D12 Bracket Dimensions

For through-hole mounting

of all D12 models;

stainless steel

hardware

included.

D12 Dimensions and Features

(glass ber optic models)

D12 Series DIN RAIL Glass Fiber Optic Sensors

*Response Mode Selection on

FVY and FVY1

models only

The excess gain curves for glass bers

in the diffuse sensing mode is given at

the immediate right. Fiber size is noted

on the curve.

The excess gain curves for glass bers

in the opposed mode are given at the far

right. Fiber size is noted on the curve.

* Include "Q" in model sufx to specify

6-inch pigtail with 4-pin pico-style QD.

Omit "Q" to specify models with 6-foot

attached cable.

Models with 30-foot attached cable are

available.

D12SN6FV(Q)* NPN sinking complementary outputs (standard 500µs response time)

D12SN6FVY(Q)* NPN sinking complementary outputs (with selectable 50µs high speed response mode)

D12SN6FVY1(Q)* NPN sinking complementary outputs (with selectable 50µs high speed response mode and 20 ms pulse stretcher)

D12SP6FV(Q)* PNP sourcing complementary outputs (standard 500µs response time)

D12SP6FVY(Q)* PNP sourcing complementary outputs (with selectable 50µs high speed response mode)

D12SP6FVY1(Q)* PNP sourcing complementary outputs (with selectable 50µs high speed response mode and 20 ms pulse stretcher)

Range and gain information for D12FV, D12FVY, and D12FVY1 Series glass ber optic sensors

Glass ber installation (refer to drawings):

1) Gently seat an o-ring onto each sensor end of the ber (above), and

push the sensor ends into the D12’s ber ports as far as they will go.

2) While holding the sensor ends snugly in place, slip the ber retaining

clip into the slot, and press the clip in until it snaps into the groove.

O-ring (supplied with fiber)

Groove

Sensor end, glass fiber

D12 Series DIN RAIL Plastic Fiber Optic Sensors

Banner Engineering Corp. 9714 Tenth Avenue No., Minneapolis, MN 55441 Telephone (763) 544-3164 FAX (763) 544-3213

*Response Mode Selection on

FPY and FPY1

models only

Excess gain curves for plastic bers

in the diffuse sensing mode are given

to the right (top row). Fiber sizes are

noted on the curves.

Excess gain curves for plastic bers

in the opposed mode are given below

(bottom row). Fiber sizes are noted on

the curves. The curve at the far lower

right uses model L2 lenses for extended

sensing range.

D12SN6FP(Q)* NPN sinking complementary outputs (standard 500µs response time)

D12SN6FPY(Q)* NPN sinking complementary outputs (with selectable 50µs high speed response mode)

D12SN6FPY1(Q)* NPN sinking complementary outputs (with selectable 50µs high speed response mode and 20 ms pulse stretcher)

D12SP6FP(Q)* PNP sourcing complementary outputs (standard 500µs response time)

D12SP6FPY(Q)* PNP sourcing complementary outputs (with selectable 50µs high speed response mode)

D12SP6FPY1(Q)* PNP sourcing complementary outputs (with selectable 50µs high speed response mode and 20 ms pulse stretcher)

Range and gain information for D12FP, D12FPY, & D12FPY1 Series plastic ber optic sensors

* Include "Q" in model sufx to specify 6-inch pigtail with 4-pin pico-style QD.

Omit "Q" to specify models with 6-foot attached cable.

Models with 30-foot attached cable are available.

D12 Dimensions and Fea-

tures (plastic ber optic models)

Plastic ber installation:

1) Cut ber ends per instructions included with the

bers. Slide the ber gripper up (open).

If .010" or .020" dia. bers are used, insert the adaptor

(drawing above) into the ports as far as it will go.

2) All bers: Insert the prepared plastic ber sensor

ends gently into the ports as far as they will go.

Slide the ber gripper back down to lock.

Adaptor (included)

is for use with

.010" or .020"

diameter bers.