1
Copyright Cirrus Logic, Inc. 2011
(All Rights Reserved)
Cirrus Logic, Inc.
http://www.cirrus.com
CS5460A
Single Phase, Bi-directional Power/Energy IC
Features
Energy Data Linearity: ±0.1% of Reading
over 1000:1 Dynamic Range.
On-Chip Functions: (Real) Energy, I V,
IRMS and VRMS, Energy-to-Pulse
Conversion
Smart “Auto-boot” Mode from Serial
EEPROM Enables Use without MCU.
AC or DC System Calibration
Mechanical Counter/Stepper Motor Driver
Meets Accuracy Spec for IEC 687/1036, JIS
Typical Power Consumption <12 mW
Interface Optimized for Shunt Sensor
V vs. I Phase Compensation
Ground-Referenced Signals with Single
Supply
On-chip 2.5 V Reference (MAX 60 ppm/°C
drift)
Simple Three-wire Digital Serial Interface
Watch Dog Timer
Power Supply Monitor
Power Supply Configurations
VA+ = +5 V; VA- = 0 V; VD+ = +3.3 V to +5 V
Description
The CS5460A is a highly integrated power mea-
surement solution which combines two
Analog-to-digital Converters (ADCs), high-speed
power calculation functions, and a serial interface
on a single chip. It is designed to accurately mea-
sure and calculate: Real (True) Energy,
Instantaneous Power, IRMS, and VRMS for single
phase 2- or 3-wire power metering applications.
The CS5460A interfaces to a low-cost shunt resis-
tor or transformer to measure current, and to a
resistive divider or potential transformer to mea-
sure voltage. The CS5460A features a
bi-directional serial interface for communication
with a microcontroller and a pulse out put engine for
which the average pulse frequency is proportional
to the real power. The CS5460A has on-chip func-
tionality to facilitate AC or DC system-level
calibration.
The “Auto-boot” feature allows the CS5460A to
function ‘stand-alone’ and to initialize itself on sys-
tem power-up. In Auto-boot Mode, the CS5460A
reads the calibration data and start-up instructions
from an external EEPROM. In this mode, the
CS5460A can operate without a microcontroller, in
order to lower the total bill-of-materials cost.
PGA
x10,x50
VA+ VD+
IIN+
IIN-
VIN+
VIN-
VREFIN
VREFOUT
VA- XIN XOUT CPUCLK DGND
CS
SDO
SDI
SCLK
INT
EOUT
Digital
Filter
High Pass
Filter
Voltage
Reference System
Clock /K Clock
Generator
Serial
Interface
Power
Calculation
Engine
(Energy
I*V
I,V )
RMS RMS
Energy-to-
Pulse
Converter
Power
Monitor
PFMON
x1
x10
4 Order
Modulator
th
RESET
Digital
Filter
Calibration
SRAM
EDIR
High Pass
Filter
2 Order
Modulator
nd
Watch Dog
Timer
MODE
Control /
APR ‘11
DS487F5
CS5460A
2DS487F5
TABLE OF CONTENTS
1. CHARACTERISTICS & SPECIFICATIONS .............................................................................5
ANALOG CHARACTERISTICS................................................................................................5
VREFOUT REFERENCE OUTPUT VO LTAG E................ ... ... .... ... ... ... ... .... ... ... ... .... ... ... ...........7
5V DIGITAL CHARACTERISTICS............................................................................................7
3.3 V DIGITAL CHARACTERISTICS........................................................................................8
ABSOLUTE MAXIMUM RATINGS ...........................................................................................8
SWITCHING CHARACTERISTICS ..........................................................................................9
2. OVERVIEW .............................................................................................................................12
2.1 Theory of Operation ...... ................... ................... .................... ................... ................... ...12
2.1.1 DS Modulators ............. ... ................ ... ... .... ... ... ... .... ... ................ ... ... .... ... ... ... ... ...12
2.1.2 High-rate Digital Low-pass Filters .......................................................................12
2.1.3 Digital Compensation Filters ............ ... ... .................... ................... ................... ...12
2.1.4 Digital High-pass Filters ...................................................................................... 12
2.1.5 Overall Filter Response . ................ ................ ................ ................ ................ ......13
2.1.6 Gain and DC Offset Adjustment ............. .... ... ... ... .................... ................... .........13
2.1.7 Real Energy and RMS Computations .................................................................13
2.2 Performing Measurements ............ ... ... ... .... ................... ................... .................... ............13
2.2.1 CS5460A Linearity Performance ...... ... ... .... ... ... ... .... ... ... ................... ...................15
2.2.2 Single Computation Cycle (C=0) ... ... ...................................................................15
2.2.3 Continuous Computation Cycles (C=1) ......................... ... ... .... ... ... ... .... ... ... ... ... ...16
2.3 Basic Application Circuit Configurations ..........................................................................16
3. FUNCTIONAL DESCRIPTION ...............................................................................................21
3.1 Pulse-Rate Output ........................ ... ... ... .... ... ... ... .............................................................21
3.2 Pulse Output for No rm al F or mat, Stepper Motor Format and Mechanical Counter Format 22
3.2.1 Normal Format .......... .... ... ... ... ... .... ... ................ ... .... ... ... ... ... .... ... ................ ... ... ...22
3.2.2 Mechanical Counter Format ................................................................................23
3.2.3 Stepper Motor Format .........................................................................................23
3.3 Auto-boot Mode Using EEPROM .....................................................................................24
3.3.1 Auto-boot Configuration ............ .... ... ................................ ... .... ... ... ... .... ... ... ... ... ...24
3.3.2 Auto-boot Data for EEPROM ..............................................................................25
3.3.3 Application Note AN225 ... ... ... ... .... ... ................... .................... ................... .........26
3.4 Interrupt and Watchdog Timer ............... .... ... ... ... .... ................... ................... .... ...............26
3.4.1 Interrupt .................. ................ ... .... ... ... ... .... ... ... ................ ... .... ... ... ... .... ... ... .........26
3.4.1.1 Clearing the Status Register ...............................................................26
3.4.1.2 Typical use of the INT pin ...................................................................26
3.4.1.3 INT Active State ..................................................................................26
3.4.1.4 Exceptions ................. .... ... ... ... .... ... ... ... ................ .... ... ... ... .... ... ... ... ......26
3.4.2 Watch Dog Timer ................................................................................................26
3.5 Oscillator Characteristics ....... .... ... ... ... ... .... ... ................... .................... ................... .........27
3.6 Analog Inputs ................ ... ... ... .... ... ... ... ... ................. ... ... ... .... ... ... ... ................ .... ... ... .........27
3.7 Voltage Reference .............. ... .... ... ................................................ ... .... ... ... ... .... ... ... ... ... ...27
3.8 Calibration .............. ... ................. ... ... ... ... .... ... ... ... ................. ... ... ... ... .... ... ... ... ...................27
3.8.1 Overview of Calibration Process .........................................................................27
3.8.2 The Calibration Registers ....................................................................................28
3.8.3 Calibration Sequence ............. ... .... ... ................................................ .... ... ... ... ... ...28
3.8.4 Calibration Signal Input Level .............................................................................29
3.8.5 Calibration Signal Frequency ..............................................................................29
3.8.6 Input Configurations for Calibrations ...................................................................29
3.8.7 Description of Calibration Algorithms ..................................................................30
3.8.7.1 AC Offset Calibration Sequence .........................................................30
3.8.7.2 DC Offset Calibration Sequence .........................................................31
3.8.7.3 AC Gain Calibration Sequence ...........................................................31
CS5460A
DS487F5 3
3.8.7.4 DC Gain Calibration Sequence ......................................................... 31
3.8.8 Duration of Calibration Sequence .... ................................................................... 31
3.9 Phase Compensation ............................ .................... ................... .................... ............... 31
3.10 Time-Base Calibration Register ..................................................................................... 32
3.11 Power Offset Register ................................................................................................... 32
3.12 Input Protection - Current Limit ...................................................................................... 32
3.13 Input Filtering ................................................................................................................. 34
3.14 Protection Against High-voltage and/or High-current Surges ........................................ 37
3.15 Improving RFI Immunity ................................................................................................ 38
3.16 PCB Layout ................................................................................................................... 38
4. SERIAL PORT OVERVIEW .................................................................................................... 38
4.1 Commands (Write Only) ........ .... ... ... ... ... .... ................... ................... .................... ............ 39
4.2 Serial Port Interface ............ ... .... ................... ................... .................... ................... ......... 42
4.3 Serial Read and Write ........ ... .... ................... ................... .................... ................... ......... 42
4.3.1 Register Write ........... .... ... ... ... ................ .... ... ... ... .... ... ... ... ... .... ............................ 42
4.3.2 Register Read ........ ... .... ... ................ ... ... .... ... ... ... .... ... ................ ... ... .... ... ... ... ... ... 42
4.4 System Initialization ...... ... ... ... ................................................................................. ... ...... 42
4.5 Serial Port Initialization .............................. ... ... ... .... ... ... ... .... ... ... ...................................... 43
4.6 CS5460A Power States ................................................................................................... 43
5. REGISTER DESCRIPTIONS ................................................................................................. 44
5.1 Configuration Register............ .... ... ... ... ... ................. ... ... ... .... ... ... ... ... ................. ... ... ... ... ...44
5.2 Current Channel DC Offset Register and Voltage Channel DC Offset Register .............. 46
5.3 Current Channel Gain Register and Voltage Channel Gain Register............................... 46
5.4 Cycle Count Register........................................................................................................46
5.5 Pulse-Rate Register ................... ... ... ... ... ..........................................................................47
5.6 I,V,P,E Signed Output Register Results........................................................................... 47
5.7 IRMS, VRMS Unsigned Output Register Results............................................................. 47
5.8 Timebase Calibration Register ............... .... ... ... ... .... ... ................ ... ... .... ... ... ... ................ ... 47
5.9 Power Offset Register ...................................................................................................... 48
5.10 Current Channel AC Offset Register and Voltage Channel AC Offset Register............. 48
5.11 Status Register and Mask Register................................................................................ 48
5.12 Control Register.............................................................................................................. 50
6. PIN DESCRIPTIONS .............................................................................................................. 51
7. PACKAGE DIMENSIONS ...................................................................................................... 53
8. ORDERING INFORMATION ................................................................................................. 54
9. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION ............................ 54
10. REVISION HISTORY ... ... .... ... ... ................................ .... ... ... ... .... ... ... ... ... .... ............................ 54
CS5460A
4DS487F5
LIST OF FIGURES
Figure 1. CS5460A Read and Write Timing Diagrams..................................................................10
Figure 2. CS5460A Auto-Boot Sequence Timing..........................................................................11
Figure 3. Data Flow.......................................................................................................................13
Figure 4. Voltage Input Filter Characteristics................................................................................14
Figure 5. Current Input Filter Characteristics ................................................................................14
Figure 6. Typical Connection Diagram (One-Phase 2-Wire, Direct Connect to Power Line)........17
Figure 7. Typical Connection Diagram (One-Phase 2-Wire, Isolated from Power Line)...............18
Figure 8. Typical Connection Diagram (One-Phase 3-Wire).........................................................19
Figure 9. Typical Connection Diagram (One-Phase 3-Wire - No Neutral Available).....................20
Figure 10. Time-plot representation of pulse output for a typical burst of pulses (Normal Format)23
Figure 11. Mechanical Counter Format on EOUT and EDIR ........................................................23
Figure 12. Stepper Motor Format on EOUT and EDIR .................................................................24
Figure 13. Typical Interface of EEPROM to CS5460A..................................................................24
Figure 14. Timing Diagram for Auto-Boot Sequence ....................................................................25
Figure 15. Oscillator Connection...................................................................................................27
Figure 16. System Calibration of Gain. .........................................................................................30
Figure 17. System Calibration of Offset. .......................................................................................30
Figure 18. Calibration Data Flow...................................................................................................30
Figure 19. Example of AC Gain Calibration ..................................................................................31
Figure 20. Input Protection for Single-Ended Input Configurations...............................................37
Figure 21. CS5460A Register Diagram.........................................................................................44
LIST OF TABLES
Table 1. Differential Input Voltage vs. Output Code......................................................................14
Table 2. Available range of ±0.1% output linearity,
with default settings in the gain/offset registers. ...........................................................15
Table 3. Default Register Values upon Reset Event.....................................................................43
CS5460A
DS487F5 5
1. CHARACTERISTICS & SPECIFICATIONS
ANALOG CHARACTERISTICS
(TA= -40 °C to +85 °C; VA+ = VD+ = +5 V ±10%; VREFIN = +2.5 V; VA- = AGND = 0 V; MCLK = 4.096 MHz,
K = 1; N = 4000 ==> OWR = 4000 Sps.)(See Notes 1, 2, 3, 4, and 5.)
Notes: 1. Bipolar Offset Errors and Full-Scale Gain Errors for the current and voltage channels refer to the respective Irms
Register and Vrms Register output, when the device is operating in ‘continuous computation cycles’ data acquisition
mode, after offset/gain system calibration sequences have been executed. Thes e specs do not apply to the error
of the Instantaneous Current/Voltage Register output.
2. Specifications guaranteed by design, characterization, and/or test.
3. Analog signals are relative to VA- and digital signals to DGND unless otherwise noted.
4. In requiring VA+ = VD+ =5 V ±10%, note that it is allowable for VA+, VD+ to differ by as much as ±200 mV, as long
as VA+ > VD+.
5. Note that “Sps” is an abbreviation for units of “samples per second”.
6. Effective Input Impedance (Zin) is determined by clock frequency (DCLK) and Input Capacitance (IC).
Zin = 1/(IC*DCLK/4). Note that DCLK = MCLK / K.
Parameter Symbol Min Typ Max Unit
Accuracy (Both Channels)
Common Mode Rejection (DC, 50, 60 Hz) CMRR 80 - - dB
Offset Drift (Without the High Pass Filter) - 5 - nV/°C
Analog Inputs (Current Channel)
Maximum Differential Input Voltage Range (Gain = 10)
{(VIIN+) - (VIIN-)} (Gain = 50) IIN -
--
-500
100 mVP-P
mVP-P
Total Harmonic Distortion THDI80 - - dB
Common Mode + Signal on IIN+ or IIN- (Gain = 10 or 50) -0.25 - VA+ V
Crosstalk with Voltage Channel at Full Scale (50, 60 Hz) - - -115 dB
Input Capacitance (Gain = 10)
(Gain = 50) Cin -
-25
25 -
-pF
pF
Effective Input Impedance (Note 6)
(Gain = 10)
(Gain = 50) ZinI
ZinI -
-30
30 -
-k
k
Noise (Referred to Input) (Gain = 10)
(Gain = 50) -
--
-20
4µVrms
µVrms
Accuracy (Current Channel)
Bipolar Offset Error (Note 1) VOSI- ±0.001 - %F.S.
Full-Scale Error (Note 1) FSEI- ±0.001 - %F.S.
Analog Inputs (Voltage Channel)
Maximum Differential Input Voltage Range {(VVIN+) - (VVIN-)} VIN --500mV
P-P
Total Harmonic Distortion THDV62 - - dB
Common Mode + Signal on VIN+ or VIN- VA- - VA+ V
Crosstalk wi th Current Channel at Full Scale (50, 60 Hz) - - -70 dB
Input Capacitance CinV -0.2-pF
Effective Input Impedance (Note 6) ZinV -5-M
Noise (Referred to Input) - - 250 µVrms
Accuracy (Voltage Channel)
Bipolar Offset Error (Note 1) VOSV- ±0.01 - %F.S.
Full-Scale Error (Note 1) FSEV- ±0.01 - %F.S.
CS5460A
6DS487F5
ANALOG CHARACTERISTICS (Continued)
Notes: 7. The minimum FSCR is limited by the maximum allowe d gain register value.
8. All outputs unloaded. All inputs CMOS level.
9. Definition for PSRR: VREFIN tied to VREFOUT, VA+ = VD+ = 5 V, a 150 mV zero-to-peak sinewave
(frequency = 60 Hz) is imposed onto the +5 V supply voltage at VA+ and VD+ pins. The “+” and “-” input
pins of both input channels are shorted to VA-. Then the CS5460A is commanded to ’continuous
computation cycles’ data acquisition mode, and digital output data is collected for the channel under
test. The zero-peak value of the digital sinusoidal output signal is determined, and this value is
converted into the zero-peak value of the sinusoidal voltage that would need to be applied at the
channel’s inputs, in order to cause the same digital sinusoidal output. This voltage is then defined as
Veq. PSRR is then (in dB):
10. When voltage level on PFMON is sagging, and LSD bit is 0, the voltage at which LSD bit is set to 1.
11. Assuming that th e LSD bit has been set to 1 (beca use PFMON voltage fell bel ow PMLO), then if/when
the PFMON voltage starts to rise again, PMHI is th e voltage level (on PFMON pin) at which the LSD bit
can be permanently reset back to 0 (with out instantaneously changing back to 1). Attempts to reset the
LSD bit before this condition is true will not be successful. This condition indicates that power has been
restored. Typically, for a given sample, the PMHI voltage will be ~100 mV above the PMLO voltage.
Parameter Symbol Min Typ Max Unit
Dynamic Chara ct e ri st ic s
Phase Compensation Range (Voltage Channel, 60 Hz) -2.4 - +2.5 °
High Rate Filter Output Word Rate (Both Channels) OWR - DCLK/1024 - Sps
Input Sample Rate DCLK = MCLK/K - DCLK/8 - Sps
Full Scale DC Calibration Range (Note 7) FSCR 25 - 100 %F.S.
Channel-to-Channel Time-Shift Error
(when PC[6:0] bits are set to “0000000”) 1.0 µs
High Pass Filter Pole Frequency -3 dB - 0.5 - Hz
Power Supplies
Power Supply Currents (Active State) IA+
ID+ (VD+ = 5 V)
ID+ (VD+ = 3.3 V)
PSCA
PSCD
PSCD
-
-
-
1.3
2.9
1.7
-
-
-
mA
mA
mA
Power Consumption Active State (VD+ = 5 V)
(Note 8) Active State (VD+ = 3.3 V)
Stand-By State
Sleep State
PC -
-
-
-
21
11.6
6.75
10
25
-
-
-
mW
mW
mW
µW
Power Supply Rejection Ratio (50, 60 Hz)
for Current Channel (Gain = 10)
(Note 9) (Gain = 50) PSRR
PSRR 56
75 -
--
-dB
dB
Power Supply Rejection Ratio (50, 60 Hz)
for Voltage Channel (Note 9) PSRR - 65 - dB
PFMON Power-Fail Detect Threshold (Note 10) PMLO 2.3 2.45 - V
PFMON “Power-Restored” Dete ct Threshold (Note 11) PMHI - 2.55 2.7 V
PSRR 20 0.150V
Veq
-------------------
log=
CS5460A
DS487F5 7
VREFOUT REFERENCE OUTPUT VOLTAGE
Notes: 12. The voltage at VREFOUT is measured across the temperature range. From these me asurements the
following formula is used to calculate the VREFOUT Temperature Coefficient:.
5V DIGITAL CHARACTERISTICS
(TA= -40 °C to +85 °C; VA+ = VD+ = 5 V ±10% VA-, DGND = 0 V) (See Notes 3, 4, and 13)
13. Note that the 5 V characteristics are guaranteed by characterizatio n. Only the more rigorous 3.3 V
digital characteristics are actually verified durin g pr od uc tio n te st.
14. Applies to all INPUT pins except XIN pin (leakage current < 50 µA) and MODE pin (leakage current <
25 µA).
Parameter Symbol Min Typ Max Unit
Reference Output
Output Voltage REFOUT +2.4 - +2.6 V
VREFOUT Temperature Coefficient (Note 12) TVREFOUT -3060ppm/°C
Load Regulation (Output Current 1 µA Source or Sink) VR-610mV
Reference Input
Input Voltage Range VREFIN +2.4 +2.5 +2.6 V
Input Capacitance - 4 - pF
Input CVF Current - 25 - nA
Parameter Symbol Min Typ Max Unit
High-Level Input Voltage
All Pins Except XIN, SCLK and RESET
XIN
SCLK and RESET
VIH 0.6 VD+
(VD+) - 0.5
0.8VD+
-
-
-
-
-
-
V
V
V
Low-Level Input Voltage
All Pins Except XIN, SCLK, and RESET
XIN
SCLK and RESET
VIL -
-
-
-
-
-
0.8
1.5
0.2VD+
V
V
V
High-Level Output Voltage (except XOUT) Iout =+5mA V
OH (VD+) - 1.0 - - V
Low-Level Output Voltage (except XOUT) Iout =-5mA V
OL --0.4V
Input Leakage Curren t (Note 14) Iin -±1±10µA
High Impedance State Leakage Current IOZ --±10µA
Digital Output Pin Capacitance Cout -5-pF
(VREFOUTMAX - VREFOUTMIN)
VREFOUTAVG TAMAX - TAMIN
1
(())1.0 x 10
()
6
TVREFOUT =
CS5460A
8DS487F5
3.3 V DIGITAL CHARACTERISTICS
(TA=-40°C to +85°C; VA+=5V±10%, VD+=3.3V±10%; VA-, DGND = 0 V) (See Notes 3, 4, and 13)
Notes: 15. All measurements performed under static conditions.
16. If VD+ = 3 V and if XIN input is generated using crystal, then XIN frequency must remain between
2.5 MHz - 5.0 MHz. If using oscillator, full XIN frequency range is available, see Switching
Characteristics.
ABSOLUTE MAXIMUM RATINGS
(DGND = 0 V; See Note 17) WARNING: Operation at or beyond these limits may result in permanent damage to
the device. Norm al op e ra tio n is not guaranteed at these extremes.
Notes: 17. All voltages with respect to ground.
18. VA+ and VA- must satisfy {(VA+) - (VA-)} +6.0 V.
19. VD+ and VA- must satisfy {(VD+) - (VA-)} +6.0 V.
20. Applies to all pins including continuous over-voltage conditions at the analog input (AIN) pins.
21. Transient current of up to 100 mA will not cause SCR latch-up.
22. Maximum DC input current for a power supply pin is ±50 mA.
23. Total power dissipation, including all input currents and output currents.
Parameter Symbol Min Typ Max Unit
High-Level Input Voltage
All Pins Except XIN, XOUT, SCLK, and RESET
XIN
SCLK and RESET
VIH 0.6 VD+
(VD+) - 0.5
0.8VD+
-
-
-
-
-
-
V
V
V
Low-Level Input Voltage
All Pins Except XIN, XOUT, SCLK, and RESET
XIN
SCLK and RESET
VIL -
-
-
-
-
-
0.48
0.3
0.2VD+
V
V
V
High-Level Output Voltage (except XIN, XOUT)Iout =+5mA V
OH (VD+) - 1.0 - - V
Low-Level Output Voltage (except XIN, XOUT) Iout =-5mA V
OL --0.4V
Input Leakage Curren t (Note 14) Iin -±1±10µA
3-State Leakage Current IOZ --±10µA
Digital Output Pin Capacitance Cout -5-pF
Parameter Symbol Min Typ Max Unit
DC Power Supplies (Notes 18 and 19)
Positive Digital
Positive Analog
Negative Analog
VD+
VA+
VA-
-0.3
-0.3
+0.3
-
-
-
+6.0
+6.0
-6.0
V
V
V
Input Current, Any Pin Except Supplies(Note 20, 21, and 22) IIN --±10mA
Output Current IOUT --±25mA
Power Dissipation (Note 23) PD--500mW
Analog Input Voltage All Analog Pins VINA (VA-) - 0.3 - (VA+) + 0.3 V
Digital Input Voltage All Digital Pins VIND DGND - 0.3 - (VD+) + 0.3 V
Ambient Operating Temperature TA-40 - 85 °C
Storage Temperature Tstg -65 - 150 °C
CS5460A
DS487F5 9
SWITCHING CHARACTERISTICS
(TA= -40 °C to +85 °C; VA+ = 5.0 V ±10%; VD+ = 3.0 V ±10% or 5.0 V ±10%; VA- = 0.0 V; Logic Levels:
Logic 0 = 0.0 V, Logic 1 = VD+; CL = 50 pF))
Notes: 24. Device parameters are specified with a 4.096 MHz clock, yet, clocks between 3 MHz to 20 MHz can be
used. However, for input frequencies over 5 MHz, an external oscillator must be used.
25. If external MCLK is use d, then duty cycle must be between 4 5% and 55% to maintain this specification.
26. Specified using 10% and 90% points on wave-form of inter est. Output loaded with 50 pF.
27. Oscillator start-up time varies with crystal parameters. This specification does not apply when using an
external clock source.
Parameter Symbol Min Typ Max Unit
Master Clock FrequencyCrystal/Internal Gate Oscillator (Note 24) MCLK 2.5 4.096 20 MHz
Master Clock Duty Cycle 40 - 60 %
CPUCLK Duty Cycle (Note 25) 40 60 %
Rise Times Any Digital Input Except SCLK (Note 26)
SCLK
Any Digital Output
trise -
-
-
-
-
50
1.0
100
-
µs
µs
ns
Fall Times Any Digital Input Except SCLK (Note 26)
SCLK
Any Digital Output
tfall -
-
-
-
-
50
1.0
100
-
µs
µs
ns
Start-up
Oscillator Start-Up Time XTAL = 4.096 MHz (Note 27) tost -60-ms
Serial Port Timing
Serial Clock Frequency SCLK - - 2 MHz
Serial Clock Pulse Width High
Pulse Width Low t1
t2
200
200 -
--
-ns
ns
SDI Timing
CS Falling to SCLK Rising t350 - - ns
Data Set-up Time Prior to SCLK Rising t450 - - ns
Data Hold Time After SCLK Rising t5100 - - ns
SCLK Falling Prior to CS Disable t6100 - - ns
SDO Timing
CS Falling to SDI Driving t7-2050ns
SCLK Falling to New Data Bit t8-2050ns
CS Rising to SDO Hi-Z t9-2050ns
Auto-boot Timing
Serial Clock Pulse Width High
Pulse Width Low t10
t11
8
8MCLK
MCLK
MODE setup time to RESET Rising t12 50 ns
RESET rising to CS falling t13 48 MCLK
CS falling to SCLK rising t14 100 8 MCLK
SCLK falling to CS rising t15 16 MCLK
CS rising to driving MODE low (to end auto-boot sequence). t16 50 ns
SDO guaranteed setu p time to SCLK rising t17 100 ns
CS5460A
10 DS487F5
CS
SCLK
MSB MSB - 1 LSB
t2
t1
t3
SDI MSB MSB - 1 LSB
Comman d Time 8 SC LKs
LSB
t6
MSB MSB - 1 LSB MSB MSB - 1
High Byte Mid Byte Low Byte
tt
45
SDI Write Timing (Not to Scale)
CS
SDO
SCLK
MSB MSB - 1 LSB
t2
t1t8
t7
SDI MSB MSB - 1 LSB
Command Time 8 SCLK s
LSB
t9
MSB MSB - 1 LSB MSB MSB - 1
High Byte Mid Byte Low Byte
Must strobe "SYNC0" command on SDI
when reading each byte of data from SDO.
SDO Read Timing (Not to Scale)
Figure 1. CS5460A Read and Write Timing Diagrams
CS5460A
DS487F5 11
RES
SDI
SCLK
t8
t14
t13
t1
1
t10
SDO
CS
t5
t4
Data from EEPROM
(Output)
(Output)
(Output)
(Input)
MODE
(Input)
t12
t15
t16
STOP
BIT LAST 8 BITS
(Input)
t17
Figure 2. CS5460A Auto-boot Sequence Timing
CS5460A
12 DS487F5
2. OVERVIEW
The CS5460A is a CMOS monolithic power mea-
surement device with a real power/energy compu-
tation engine. The CS5460A combines two
programmable gain amplifiers, two modulators,
two high rate filters, system calibration, and
rms/power calculation functions to provide instan-
taneous voltage/current/power data samples as
well as periodic computation results for real (bill-
able) energy, VRMS, and IRMS. In order to accom-
modate lower cost metering applications, the
CS5460A can also ge nerate pulse-t rain signals on
certain output pins, for which the number of pulses
emitted on the pins is proportional to the quantity of
real (billable) energy registered by the device.
The CS5460A is optimized for power measure-
ment applications and is designed to inte rface to a
shunt or current transformer to measure current,
and to a resistive divider or p otential transformer to
measure voltage. To accommodate various input
voltage levels, the current channel includes a pro-
grammable gain amplifier (PGA) which provides
two full-scale input levels, while the voltage chan-
nel’s PGA provides a single input voltage range.
With a single +5 V supply on VA+/-, both of the
CS5460A’s input channels can accomodate com-
mon mode + signal levels between -0.25 V and
VA+.
The CS5460A includes two high-rate digital filters
(one per channel), which decimate/integrate the
output from the 2 modulators. The filters yield
24-bit output data at a (MCLK/K)/1024 output word
rate (OWR). The OWR can be thought of as the ef-
fective sample frequency of the voltage channel and
the current channel.
To facilitate communication to a microcontroller,
the CS5460A includes a simple three-wire serial
interface which is SPI™ and Microwire™ compati-
ble. The serial port has a Schmitt Trigger input on
its SCLK (serial clock) and RESET pins to allow for
slow rise time signals.
2.1 Theory of Operation
A computational flow diagram for the two data
paths is shown in Fig. 3. The reader should refer to
this diagram while reading the following data pro-
cessing description, which is covered
block-by-block.
2.1.1 Modulators
The analog waveforms at the voltage/current chan-
nel inputs are subject to the gains of the input
PGAs (not shown in Figure 3). These waveforms
are then sampled by the delta-sigma modulators at
a rate of (MCLK/K)/8 Sps.
2.1.2 High-rate Digital Low-pass Filters
The data is then low-pass filtered, to remove
high-frequency noise from the modulator output.
Referring to Figure 3, the high rate filter on the volt-
age channel is implemented as a fixed Sinc2 filter.
The current channel uses a Sinc4 filter, which al-
lows the current channel to make accurate mea-
surements over a wider span of the total input
range, in comparison to the accuracy range of the
voltage channel. (This subject is discussed more in
Section 2.2.1)
Also note from Figure 3 that the digital data on the
voltage channel is subjected to a variable time-d e-
lay filter. The amount of delay depend s on the va l-
ue of the seven phase compensation bits (see
Phase Compensation). Note that when the phase
compensation bits PC[6:0] are set to their default
setting of “0000000” (and if MCLK/K = 4.096 MHz)
then the nominal time delay that is imposed on the
original analog voltage input signal, wit h respect to
the original analog current input signal, is ~1.0 µs.
This translates into a delay of ~0.0216degrees at
60 Hz.
2.1.3 Digital Compensation Filters
The data from both channels is then passed
through two FIR compensation filters, whose pur-
pose is to compensate for the magnitude roll-of f of
the low-pass filtering operation (mentioned earli-
er).
2.1.4 Digital High-pass Filters
Both channels provide an optional high-pass filter
(denoted as “HPF” in Figure 3) which can be en-
gaged into the signal path, to remove the DC con-
tent from the current/voltage signal before the
RMS/energy calculations are made. These filters
are activated by enabling certain bits in the Config-
uration Register.
If the high-pass filter is engaged in only one of the
two channels, then the all-pass filter (see “APF” in
CS5460A
DS487F5 13
Figure 3) will be enabled on the other channel; in
order to preserve the relative phase relationship
between the voltage-sense and current-sense in-
put signals. For example, if the H PF is engaged for
the voltage channel, but not the current channel,
then the APF will be engaged in the current channel,
to nullify the additional phase delay introduced by
the high-pass filter in the current channel.
2.1.5 Overall Filter Response
When the CS5460A is driven with a 4.096 MHz
clock (K = 1), the composite magnitude response
(over frequency) of the voltage channel’s input fil-
ter network is shown in Figure 4, while the com-
posite magnitude response of the current
channel’s input filter network is given in Figure 5.
Note that the composite filter response of both
channels scales with MCLK frequency and K.
2.1.6 Gain and DC Offset Adjustment
After filtering, the instantaneous voltage and cur-
rent digital codes are subjected to offset/gain ad-
justments, based on the values in the DC offset
registers (additive) and the gain registers (multipli-
cative). These registers are used for calibration of
the device (see Section 3.8, Calibration). After off-
set and gain, the 24-bit instantaneous data sample
values are stored in the Instantaneous Voltage and
Current Registers.
2.1.7 Real Energy and RMS Computations
The digital instantaneous voltage and current d ata
is then processed further. Referring to Figure 3, the
instantaneous voltage/current data samples are
multiplied together (one multiplication for each pa ir
of voltage/current samples) to form instantaneous
(real) power samples. After each A/D conversion
cycle, the new instantaneous power sample is
stored in the Instantaneous Power Regi ster.
The instantaneous power samples are then
grouped into sets of N samples (where N = value in
Cycle Count Register). The cumulative sum of
each successive set of N instantaneous power is
used to compute the result stored in the Energy
Register, which will be proportional to the amount
of real energy registered by the device during the
most recent N A/D conversion cycles. Note from
Figure 3 that the bits in this running energy sum
are right-shifted 12 times (divided by 4096) to
avoid overflow in the Energy Register. RMS calcu-
lations are also performed on the data using the
last N instantaneous voltage/current samples, and
these results can be read from the RMS Voltage
Register and the RMS Current Register.
2.2 Performing Measurements
To summarize Section 2.1, the CS5460A performs
measurements of instantaneous current and in-
stantaneous voltage, and f rom this, performs com-
putations of the corresponding instantaneous
power, as well as periodic calculations of real en-
ergy, RMS current, and RMS voltage. These mea-
surement/calculation results are available in the
form of 24-bit signed and unsigned words. The
scaling of all output words is normalized to unity
VOLTAGE
SINC2
+
x
V*
gn
x
V*
CURRENT SINC4+x
I*
gn
xx
TBC *
DELAY
REG DELAY
REG FIR HPF
APF
Configuration Register *
PC[6:0] Bits
xI*
RMS
N
V*
RMS
N
4096
EtoF
E*
E
Eout
dir
PULSE-RATE*
* DENOTES REGISTER NAME
HPF
APF
FIR
SINC2
I*
P*
N
SINC2
-
-
I
ACoff
*
I
DCoff
*
V
ACoff
*
V
DCoff
*
+
P
off
*
÷
N
÷
N
Figure 3. Data Flow.
CS5460A
14 DS487F5
full-scale. Note that the 24-bit signed ou tput words
are expressed in two’s complement format. The
24-bit data words in the CS5460A output registers
represent values between 0 and 1 (for unsigned
output registers) or between -1 and +1 (for signed
output registers). A register value of 1 represents
the maximum possible value. Note that a value of
1.0 is never actually obta ined in the registers of the
CS5460A. As an illustration, in any of the signed
output registers, the maximum register value is
[(2^23 - 1) / (2^23)] = 0.999999880791. After each
A/D conversion, the CRDY bit will be asserted in
the Status Register, and the INT pin will also be-
come active if the CRDY bit is unmasked (in the
Mask Register). The assertion of the CRDY bit in-
dicates that new instantaneous 24-bit voltage and
current samples have been collected, and these
two samples have also been multiplied together to
provide a corresponding instantaneous 24-bit pow-
er sample.
Table 1 conveys the typical relationship between
the differential input voltage (across the “+” and “-”
input pins of the voltage channel input) and the cor-
responding output code in the Instantaneous Volt-
age Register. Note that this table is applicable for
the current channel if the current channel’s PGA
gain is set for the “10x” gain mode.
The VRMS, IRMS, and energy calculations are up-
dated every N conversions (which is known as 1
“computation cycle”), where N is the value in the
Cycle Count Register. At the end of each computa-
tion cycle, the DRDY bit in the Mask Register will
be set, and the INT pin will become active if the
DRDY bit is unmasked.
DRDY is set only after each computation cycle has
completed, whereas the CRDY bit is asserted after
each individual A/D conversion. Bits asserted by
the CS5460A must be cleared before being assert-
ed again. If the Cycle Count Register value (N) is
set to 1, all output calculations are instantaneous,
and DRDY will indicate when instan taneous calcu-
lations are finished, just like the CRDY bit. For the
RMS results to be valid, the Cycle-Count Register
must be set to a value greater than 10 .
The computation cycle frequency is derived from
the master clock, and has a value of
(MCLK/K)/(1024*N). Under defa ult conditions, with
-2.5
-2.0
-1.5
-1.0
-0.5
0.0
0.5
Frequency (Her tz)
Gain (dB)
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Figure 4. Voltage Input Filter Characteristics
Input Voltage (DC) Output Code
(hexidecimal) Output Code
(decimal)
+250 mV 7FFFFF 8388607
14.9 nV to 44.7 nV 000001 1
-14.9 nV to 14.9 nV 000000 0
-44.7 nV to -14.9 nV FFFFFF -1
-250 mV 800000 -8388608
Table 1. Differential Input Voltage vs. Output Code
-2.5
-2
-1.5
-1
-0.5
0
0.5
0 200 400 600 800 1000 1200 1400 1600 1800 2000
Ga in (dB )
Frequency ( Hertz)
Figure 5. Current Input Filter Characteris tics
CS5460A
DS487F5 15
a 4.096 MHz clock at XIN, and K = 1, instanta-
neous A/D conversions for voltage, current, and
power are performed at a 4000 Sps rate, whereas
IRMS, VRMS, and energy calculations are per-
formed at a 1 Sps rate.
2.2.1 CS5460A Linearity Performance
Table 2 lists the range of input levels (as a percent-
age of full-scale) over which the (linearity + varia-
tion) of the results in the Vrms, Irms and Energy
Registers are guaranteed to be within ±0.1 % of
reading after the completion of each successive
computation cycle. Note that until the CS5460A is
calibrated (see Calibration) the accuracy of the
CS5460A with respect to a reference line-voltage
and line-current level on the power mains is not
guaranteed to within ±0.1%. After both channels of
the device are calibrated for offset/gain, the ±0.1%
of reading spec will also reflect accuracy of the
Vrms, Irms, and Energy Register results. Finally,
observe that the maximum (full-scale) differential
input voltage for the voltage channel (and current
channel, when its PGA is set for 10x gain) is
250 mV (nominal). If the gain registers of both
channels are set to 1 (default) and the two DC
offset registers are set to zero (default), then a
250mV DC signal applied to the voltage/current
inputs will measure at (or near) the maximum
value of 0.9999... in the RMS Current/Voltage
Registers. Remember that the RMS value of a
250 mV (DC) signal is also 250 mV. However, for
either input channel, it wo uld not be practical to in-
ject a sinusoidal voltage with RMS value of
250 mV. This is because when the instantaneous
value of such a sine wave is at or near the level of
its positive/negative peak regions (over each cy-
cle), the voltage level of this signal would exceed
the maximum differential input voltage range of the
input channels. The largest sine wave voltage sig-
nal that can be presented across the inputs, with
no saturation of the inputs, is:
250 mV / sqrt(2) = ~176.78 mV (RMS),
which is ~70.7% of full-scale. This would imply that
for the current channel, the (linearity+variation) tol-
erance of the RMS measurements for a purely si-
nusoidal 60 Hz input signal could be measured to
within ±0.1% of rea ding over a magnitude range of
0.2% - 70.7% of the maximum full-scale differen-
tial input voltage level.
The range over which the (linearity + variation) will
remain within ±0.1% can often be increased by se-
lecting a value for the Cycle-Count Register such
that the time duration of one computation cycle is
equal to (or very close to) a whole-number of pow-
er-line cycles (and N must be greater than or equal
to 4000). For example, with the cycle count set to
4200, the ±0.1% of reading (linearity + variation)
range for measurement of a 60 Hz sinusoidal cur-
rent-sense voltage signal can be increased beyond
the range of 0.2% - 70.7%. The accuracy range
will be increased because (4200 samples / 60 Hz)
is a whole number of cycles (70). Note that this in-
crease in the measuremen t range refers to an ex-
tension of the low end of the input scale (i.e., this
does not extend the high-end of the range above
100% of full-scale). This enables accurate mea-
surement of even smaller power-line current lev-
els, thereby extending the load range over which
the power meter can make accurate energy mea-
surements. Increasing the accuracy range can be
beneficial for power metering applications which
require accurate power metering over a very large
load range.
2.2.2 Single Computation Cycle (C=0)
Note that ‘C’ refers to the value of the C bit, con-
tained in the ‘Start Conversions’ command (see
Section 4.1). This commands instructs the
CS5460A to perform conversions in ‘single compu-
tation cycle’ data acquisition mode. Based on the
value in the Cycle Count Register, a sin gle compu-
tation cycle is performed after a ‘Start Conversions’
command is sent to the serial interface. After the
computations are complete, DRDY is set. 32
SCLKs are then needed to read out a calculation
Energy Vrms Irms
Range (% of FS) 0.1% - 100% 50% - 100% 0.2% - 100%
Max. Differential
Input not applicable V-channel:
±250 mV I-channel:
±250 mV 10x
±50 mV 50x
Linearity 0.1% of
reading 0.1% of
reading 0.1% of
reading
Table 2. Available range of ±0.1% output linearity, with
default settings in the gain/offset registers.
CS5460A
16 DS487F5
result from one of several result reg isters. The fir st
8 SCLKs are used to clock in the command to de-
termine which register is to be read. The last 24
SCLKs are used to read the desired register. After
reading the data, the serial port remains in the ac-
tive state, and waits for a new command to be is-
sued. (See Section 3 for more details on reading
register data from the CS5460A).
2.2.3 Continuous Computation Cycles
(C=1)
When C = 1, the CS5460A will perform conversions
in ‘continuous computation cycles’ data acquisition
mode. Based on the information provided in the Cy-
cle Count Register, computation cycles are repeat-
edly perform ed on the voltage and curren t channels
(after every N conversions). Computation cycles
cannot be started/stopped on a ‘per-chan nel’ basis.
After each computation cycle is completed, DRDY
is set. Thirty-two SCLKs are then needed to read a
register. The first 8 SCLKs are used to clock in the
command to determine which results register is to
be read. The last 24 SCLKs are used to read out the
24-bit calculation result. While in this acquisition
mode, the designer/programmer m ay choose to ac-
quire (read) only those calculations required for
their particular application, as DRDY repeatedly in-
dicates the availability of new data. N ote again that
the MCU firmware must reset the DRDY bit to “0”
before it can be asserted again.
Referring again to Figure 3, note that within the
Irms and Vrms data paths, prior to the square-root
operation, the instantaneous voltage/current data
is low-pass filtered by a Sinc2 filter. Then the data
is decimated to every Nth sample. Because of the
Sinc2 filter operation, the first outp ut for each chan-
nel will be invalid (i.e. all RMS calculations are in-
valid in the ‘single computation cycle’ data
acquisition mode and the first RMS calculation re-
sults will be invalid in the ‘continuous computation
cycles’ data acquisition mode). However, all ener-
gy calculations will be valid since energy calcula-
tions do not require this Sinc2 operation.
If the ’Start Conversions’ command is issued to the
CS5460A (see Section 4.1, Commands (Write On-
ly)), and if the ‘C’ bit in this command is set to a val-
ue of ‘1’, the device will remain in its active state.
Once commanded into continuous computation
cycles data acquisition mode, the CS5460A will
continue to perform A/D conversions on the volt-
age/current channels, as well as all subsequent
calculations, until:
1) the ‘Power-Up/Halt’ command is received
through the serial interface, or
2) loss of power, or
3) the RS bit in the Configuration Register is as-
serted (‘software reset’), or
4) the /RESET pin is asserted and then de-assert-
ed (‘hardware reset’).
2.3 Basic Application Circuit
Configurations
Figure 6 shows the CS5460A connected to a ser-
vice to measure power in a single-phase 2-wire
system operating from a single power supply. Note
that in this diagram the shunt resistor used to mon-
itor the line current is connected on the “Line” (hot)
side of the power mains. In most residential power
metering applications, the power meter’s cur-
rent-sense shunt resistor is intentionally placed on
the ‘hot’ side of the power mains in order to help
detect any attempt by the subscriber to steal pow-
er. In this type of shunt-resistor configuration, no te
that the common-mode level of the CS5460A must
be referenced to the hot side of the power line. This
means that the common-mode potential of the
CS5460A will typically oscillate to very high posi-
tive voltage levels, as well as very high negative
voltage levels, with respect to earth ground poten-
tial. The designer must therefore be careful when
attempting to interface the CS5460A’s digital out-
put lines to an external digital interface (such as a
LAN connection or other communication network).
Such digital communication networks may require
that the CMOS-level digital interface to the meter is
referenced to an earth -ground. In such cases, the
CS5460A’s digital serial interface pins must be iso-
lated from the external digital interface, so that
there is no conflict between the ground refere nces
of the meter and the external interface. The
CS5460A and associate circuitry should be en-
closed in a protective insulated case when u sed in
this configuration, to avoid risk of harmful electric
shock to humans/animals/etc.
Figure 7 shows how the same single-phase
two-wire system can be metered while achieving
CS5460A
DS487F5 17
complete isolation from the power lines. This isola-
tion is achieved using three transformers. One
transformer is a general-purpose voltage trans-
former, used to supply the on-board DC power to
the CS5460A. A second transformer is a high-pre-
cision, low-impedance voltage transformer (often
called a ‘potential transformer’) with very little
roll-off/phase delay, even at the higher harmonics.
A current transformer is then used to sense the line
current. A burden resistor placed across the sec-
ondary of the current transformer creates the cur-
rent-sense voltage signal, for the CS5460A’s
current channel inputs. Because the CS5460A is
not directly connected to the power mains, isola-
tion is not required for the CS5460A’s digital inter-
face.
Figure 8 shows the CS5460A configured to mea-
sure power in a single-phase 3-wire system. In
many 3-wire residential power systems within the
United States, only the two Line terminals are
available (neutral is not available). Figure 9 shows
how the CS5460A can be configured to meter a
3-wire system when no neutral is available.
VA+ VD+
0.1 µF100 µF
500
470 nF
500
N
R
1
R
2
10
14
VIN+
9
VIN-
IIN-
10
15
16 IIN+
PFMON
CPUCLK
XOUT
XIN Optional
Clock
Source
Serial
Data
Interface
RESET
17
2
1
24
19
CS 7
SDI 23
SDO 6
SCLK 5
INT 20
EDIR
EOUT
0.1 µF
VREFIN
12
VREFOUT
11
VA- DGND
13 4
3
To Service
2.5 MHz to
20 MHz
0.1 µF
C
10 k
5k
L
R
Shunt
V+
*
* Refer to Input Protection
CS5460A
*
** Refer to Input Filtering
R
V-
*
R
I-
*
R
I+
*
C
I+
**
ISOLATION
120 VAC
Mech. Counter
Stepper Motor
or
22
21
+
NOTE: Current channel
input measures voltage
(just like voltage input).
C
V-
**
C
I-
**
C**
Vdiff
C**
Idiff
Figure 6. Typical Connection Diagram (One-Phase 2-Wire, Direct Connect to Power Line)
CS5460A
18 DS487F5
VA+ VD+
0.1µF
200µF
200
N
10
14
VIN+
9
VIN-
IIN-
10
15
16 IIN+
PFMON
CPUCLK
XOUT
XIN Optional
Clock
Source
RESET
17
2
1
24
CS
SDI
SDO
SCLK
INT
EDIR 22
EOUT
21
0.1 µF
VREFIN
12
VREFOUT
11
VA- DGND
13 4
3
To Service
2.5 MHz to
20 MHz
0.1 µF
10 k
5k
L
* Refer to Input Protection
M:1
R
N:1
Low Phase-Shift
Potential Transformer
Current
Transformer
CS5460A
** Refer to Input Filtering
R
V+
*
R
V-
*
C
Vdiff
**
R
I-
*
R
I+
*
C**
Burden Idiff
Voltage
Transformer
120 VAC
12 VAC
12 VAC
200
Serial
Data
Interface
19
7
23
6
5
20
Mech. Counter
Stepper Motor
or
1k
1k
1k
1k
+
NOTE: Current channel
input measures voltage
(just like voltage input).
C
V+
**
C
V-
**
C
I+
**
C
I-
**
Figure 7. Typical Connection Diagram (One-Phase 2-Wire, Is olated from Power Line)
CS5460A
DS487F5 19
VA+ VD+
0.1 µF
100 µF
500
470 nF
500
N
R3R4
RBurden
10
14
VIN+
9
VIN-
IIN-
10
16
15
IIN+
PFMON
CPUCLK
XOUT
XIN Optional
Clock
Source
RESET
17
2
1
24
CS
SD
SDO
SCLK
INT
EDIR
EOUT
0.1 µF
VREFIN
12
VREFOUT
11
DGND
13 4
3
To Service
2.5 MHz to
20 MHz
0.1 µF
L1L2
10 k
5k
VA-
* Refer to Input Protection
R1
R
2
To Service
** Refer to Inp u t F i lter in g
RI+
*
RI-
*
22
21
Mech. Cou n ter
Stepper Motor
or
1k
1k
120 VAC 120 VA C
240 VAC
Serial
Data
Interface
19
7
23
6
5
20
I
Earth
Ground
C**
Idiff
C**
Vdiff
+
NOTE: Current channel
input measures voltage
(just like voltage input).
CI+
**
C**
I-
CV+
**
C**
V-
CS5460A
Figure 8. Typical Connection Diagra m (One-Phase 3-Wire)
CS5460A
20 DS487F5
VA+ VD+
CS5460A
0.1 µF
1
k
235nF
500
R
1
R
2
10
14
VIN+
9
VIN-
IIN-
10
16
15
IIN+
PFMON
CPUCLK
XOUT
XIN Optional
Clock
Source
RESET
17
2
1
24
CS
SDI
SDO
SCLK
INT
EDIR
EOUT
0.1 µF
VREFIN
12
VREFOUT
11
DGND
13 4
3
To Service
2.5 MHz to
20 MHz
0.1 µF
L
1
L
2
10 k
5k
VA-
C
V+
* Refer to Input Protection
*
To Service
*
** Refer to Input Filtering
R
I+
*
R
I-
*
R
V-
*
Serial
Data
Interface
19
7
23
6
5
20
ISOLATION
22
21
Mech. Counter
Stepper Motor
or
R
Burden
1k
1k
240 VAC
+
NOTE: Current channel
input measures voltage
(just like voltage input).
C
**
V-
C**
Vdiff
C
I+
**
C
**
I-
C**
Idiff
100 µF
Figure 9. Typical Connection Diagram (On e-Phase 3-Wire - No Neutral Available)
CS5460A
DS487F5 21
3. FUNCTIONAL DESCRIPTION
3.1 Pulse-Rate Output
As an alternative to reading the real energy
through the serial port, the EOUT and EDIR pins
provide a simple interface with which signed ener-
gy can be accumulated. Each EOUT pulse repre-
sents a predetermined quantity of energy. The
quantity of energy represented in one pulse can be
varied by adjusting the value in the Pulse-Rate
Register. Corresponding pulses on the EDIR out-
put pin signify that the sign of the energy is nega-
tive. Note that these pulses are not influenced by
the value of the Cycle-Count Register, and they
have no reliance on the computation cycle, de-
scribed earlier. With MCLK = 4.096 MHz, K = 1,
the pulses will have an average frequency (in Hz)
equal to the frequency setting in the Pulse Rate
Register when the input signals into the voltage
and current channels cause full-scale readings in
the Instantaneous Voltage and Current Registers.
When MCLK/K is not equal to 4.096 MHz, the
pulse-rate should be scaled by a factor of
4.096 MHz / (MCLK/K) to get the actual output
pulse-rate.
EXAMPLE #1: For a power line with maximum rat-
ed levels of 250 V (RMS) and 20 A (RMS), the
pulse-frequency on the EOUT pin needs to be
‘IR’ = 100 pulses-per-second (100 Hz) when the
RMS-voltage and RMS-current levels on the power
line are 220 V and 15 A respectively. To meet this
requirement, the pulse-rate frequency (‘PR’) in the
Pulse-Rate Register must be set accordingly.
After calibration, the first step to finding the value
of ‘PR’ is to set the voltage and current sensor gain
constants, KV and KI, such that there will be ac-
ceptable voltage levels on the CS5460A inputs
when the power line voltage and current leve ls are
at the maximum values of 250 V and 20 A. KV and
KI are needed to determine the appropriate ratios
of the voltage/current transformers and/or shunt
resistor values to use in the front-end voltage/cur-
rent sensor networks.
For a sinewave, the largest RMS valu e that can be
accurately measured (without over-driving the in-
puts) will register ~0.7071 of the maximum DC in-
put level. Since power signals are often not
perfectly sinusoidal in real-world situations, and to
provide for some over-range capability, the RMS
Voltage Register and RMS Current Register is set
to measure 0.6 when the RMS-values of the
line-voltage and line-current levels are 250 V and
20 A. Therefore, when the RMS registers measure
0.6, the voltage level at the inputs will be
0.6 x 250 mV = 150 mV. The sensor gain con-
stants, KV and KI, are determined by demanding
that the voltage and current channel inputs should
be 150 mV RMS when the power line voltage and
current are at the maximum values of 250 V and
20 A.
KV= 150 mV / 250 V = 0.0006
KI= 150 mV / 20 A = 0.0075
These sensor gain constants are used to calculate
what the input voltage levels will be on the
CS5460A inputs when the line-voltage and
line-current are 220 V and 15 A. These values are
VVnom and VInom.
VVnom =KV* 220 V = 132 mV
VInom =KI* 15 A = 112.5 mV
The pulse rate on EOUT will be at ‘PR’ pulses per
second (Hz) when the RMS-levels of voltage/cur-
rent inputs are at 250 mV. When the voltage/cur-
rent inputs are set at VVnom and VInom, the pulse
rate needs to be ‘IR’ = 100 pulses per second. IR
will be some percentage of PR. The percentage is
defined by the ratios of VVnom/250 mV and
VInom/250 mV with the following formula:
From this equation the value of ‘PR’ is shown as:.
Therefore the Pulse-Rate Register is set to
~420.875 Hz, or 0x00349C.
The above equation is valid when current channel
is set to x10 gain. If current channel gain is set to
x50, then the equation becomes:
PulseRate IR PR VVnom
250mV
------------------- VInom
250mV
-------------------
==
PR IR
VVnom
250mV
------------------ VInom
250mV
------------------
--------------------------------------------100Hz
132mV
250mV
------------------ 112.5mV
250mV
-----------------------
------------------------------------------------
==
PR IR
VVnom
250mV
------------------ VInom
50mV
---------------
-----------------------------------------
=
CS5460A
22 DS487F5
EXAMPLE #2: The required number of pulses per
unit energy present at EOUT is specified to be
500 pulses/kW-hr; given that the maximum
line-voltage is 250 V (RMS) and the maximum
line-current is 20 A (RMS). In such a situation, the
nominal line voltage and current do not determine
the appropriate pulse-rate setting. Instead, the
maximum line levels must be considered. As be-
fore, the given maximum line-voltage and line-cur-
rent levels are used to determine KV and KI:
KV= 150 mV / 250 V = 0.0006
KI=150mV/20A=0.0075
Again the sensor gains are calculated such that the
maximum line-voltage and line-current levels will
measure as 0.6 in the RMS Voltage Register and
RMS Current Register.
The required Pulse-Rate Register setting is now
determined by using the following equation:
Therefore PR = ~1.929 Hz.
Note that the Pulse-Rate Register cannot be set to
a frequency of exactly 1.929 Hz. The closest set-
ting that the Pulse-Rate Register can obtain is
0x00003E = 1.9375 Hz. To improve the accuracy,
either gain register can be programmed to correct
for the round-off error in PR. This value would be
calculated as
In the last example, suppose a value for MCLK/K
of 3.05856 MHz. When MCLK/K is not equal to
4.096 MHz, the result for ‘PR’ that is calculated for
the Pulse-Rate Register must be scaled by a cor-
rection factor of: 4.096 MHz / (MCLK/K). In this
case the result is scaled by 4.096/3.0 5856 to get a
final PR result of ~2.583 Hz.
3.2 Pulse Output for Normal Format,
Stepper Motor Format and Mechanical
Counter Format
The duration and shape of the pu lse outputs at the
EOUT and EDIR pins can be set for three diffe rent
output formats. The default setting is for Normal
output pulse format. When the pulse is set to either
of the other two formats, the time duration and/or
the relative timing of the EOUT and EDIR pulses is
increased/varied such that the pulses can drive e i-
ther an electro-mechanical counter or a stepper
motor. The EOUT and EDIR output pins are capa-
ble of driving certain low-voltage/low-power coun-
ters/stepper motors directly. This depends on the
drive current and voltage level requirements of th e
counter/motor. The ability to set the pulse output
format to one of the three available formats is con-
trolled by setting certain bits in the Control Regis-
ter.
3.2.1 Normal Format
Referring to the description of the Control Register
in Section 5., Register Descriptions, if both the
MECH and STEP bits are set to ‘0’, the pulse out-
put format at the EOUT and EDIR pins is illustrated
in Figure 10. These are active-low pulses with very
short duration. The pulse duration is an integer
multiple of MCLK cycles, approximately equal to
1/16 of the period of the contents of the Pulse-Rate
Register. However for Pulse-Rate Register set-
tings less than the sampling rate (which is
[MCLK/8]/1024), the pulse duration will remain at a
constant duration, which is eq ual to the durat ion of
the pulses when the Pulse-Rate Register is set to
[MCLK/K]/1024. The maximum pulse frequency
from the EOUT pin is therefore [MCLK/K]/16.
When energy is positive, EDIR is always high.
When energy is negative, EDIR has the same out-
put as EOUT. When MCLK/K is not equal to
4.096 MHz, the true pulse-rate can be found by
first calculating what the pulse-rate would be if a
4.096 MHz crystal is used (with K = 1) and then
scaling the result by a factor of
(MCLK/K) / 4.096 MHz.
When set to run in Normal pulse out put format, the
pulses may be sent out in “bursts” depending on
both the value of the Pulse-Rate Register as well
as the amount of billable energy that was regis-
tered by the CS5460A over the most recent A/D
sampling period, which is (in Hz): 1 / [(MCLK/K) /
1024]. A running total of the energy accumulation
is maintained in an internal register (not accessible
to the user) inside the CS5460A. If the amount of
energy that has accumulated in this register over
the most recent A/D sampling period is equal to or
greater than the amount of energy that is repre-
PR 500 pulses
kW hr
------------------ 1hr
3600s
-------------- 1kW
1000W
------------------250mV
KV
------------------ 250mV
KI
------------------
=
Ign or Vgn PR
1.929
------------- 1.00441 0x404830==
CS5460A
DS487F5 23
sented by one pulse, the CS5460A will issue a
“burst” of one or more pulses on EOUT (and also
possibly on EDIR). The CS5460A will issue as
many pulses as are necessary to reduce the run-
ning energy accumulation value in this register to a
value that is less than the energy represented in
one pulse. If the amount of energy that has been
registered over the most recent sampling period is
large enough that it cannot be expressed with only
one pulse, then a burst of pulses will be issued,
possibly followed by a period of time during which
there will be no pulses, until the next A/D sampling
period occurs. After the pu lse or pulses are issued,
a certain residual amount of energy may be left
over in this internal energy accumulation register,
which is always less (in magnitude) than the
amount of energy represented by one pulse. In this
situation, the residual energy is not lost or discard-
ed, but rather it is maintained and added to the en-
ergy that is accumulated during the next A/D
conversion cycle. The amount of residual energy
that can be left over becomes larger as the
Pulse-Rate Register is set to lower and lower val-
ues, because lower Pulse-Rate Register values
correspond to a higher amount of energy per pulse
(for a given calibration).
3.2.2 Mechanical Counter Format
Setting the MECH bit in the Control Register to ‘1’
and the STEP bit to ‘0’ enables wide-stepping puls-
es for mechanical counters and similar discrete
counter instruments. In this format, active-low puls-
es are 128 ms wide when using a 4.096 MHz crys-
tal and K = 1. When energy is positive, the pulses
appear on EOUT. When energy is negative, pulses
appear on EDIR. To insure that pulses will not oc-
cur at a rate faster than t he 128 ms pulse duration,
or faster than the mechanical counter can accom-
modate, the Pulse-Rate Register should be set to
an appropriate value. Because the duration of
each pulse is set to 128 ms, the maximum output
pulse frequency is limited to ~7.8 Hz (for
MCLK/K = 4.096 MHz). For values of MCLK / K
different than 4.096 MHz, the duration of one pulse
is (128 * 4.096 MHz) / (MCLK / K) milliseconds.
See Figure 11 for a diagram of the typical pulse
output.
3.2.3 Stepper Motor Format
Setting the STEP bit in the Control Register to ‘1’
and the MECH bit to ‘0’ transforms the EOUT and
EDIR pins into two stepper motor phase outputs.
When enough energy has been registered by the
CS5460A to register one positive/negative energy
EOUT
EDIR
Pulse-Rate Register Period
16 n
(MCLK / K)
=
for Integer n
t
t
2
=
x
Positive Energy Burst Negative Energy Burst
. . .
. . .
. . .
. . .
Figure 10. Time-plot representation of pulse output for a typical burst of pulses (Normal Format)
128 ms
128 ms
EOUT
EDIR Positive Energy Negative Energy
...
...
...
...
Figure 11. Mechanical Counter Format on EOUT and EDIR
CS5460A
24 DS487F5
pulse, one of the output pins (either EOUT or ED-
IR) changes state. When the CS5460A must issue
another energy pulse, the other output changes
state. The direction the motor will rotate is deter-
mined by the order of the state changes. When en-
ergy is positive, EOUT will lead EDIR such that the
EOUT pulse train will lead the EDIR pulse train by
~1/4 of the periods of these two pulse train signal.
When energy is negative, EDIR will lead EOUT in
a similar manner. See Figure 12.
3.3 Auto-boot Mode Using EEPROM
The CS5460A has a MODE pin. When the MODE
pin is set to logic low, the CS5460A is in normal op-
erating mode, called host mode. This mode de-
notes the normal operation of the part, that has
been described so far. But when this pin is set to
logic high, the CS5460A auto-boot mode is en-
abled. In auto-boot mode, the CS5460A is config-
ured to request a memory download from an
external serial EEPROM. The downlo ad sequence
is initiated by driving the RESET pin to logic high.
Auto-boot mode allows the CS5460A to operate
without the need for a microcontroller. Note that if
the MODE pin is left unconnected, it will default to
logic low because of an internal pull-down on the
pin.
3.3.1 Auto-boot Configuration
Figure 13 shows the typical connections between
the CS5460A and a serial EEPROM for proper au-
to-boot operation. In this mode, CS and SCLK are
driven outputs. SDO is always an output. During
the auto-boot sequence, the CS5460A drives CS
low, provides a clock output on SCLK, and drives
out-commands on SDO. It receives the EEPROM
data on SDI. The serial EEPROM must be pro-
grammed with the user-specified commands and
register data that will be used by the CS5460A to
change any of the default register values (if de-
sired) and begin conversions.
Figure 13 also shows the external connections that
would be made to a calibrator device, such as a PC
EOUT
EDIR Positive Energy Negative Energy
...
... ...
...
Figure 12. Stepper Motor Format on EOUT and EDIR
CS5460A EEPROM
/EOUT
/EDIR
MODE
SCK
SDI
SDO
/CS
SCK
SO
SI
/CS
Connector to
Calibrator
VD+
5 K
5 K
Mech. Counter
Stepper Motor
or
Figure 13. Typical Interface of EEPROM to CS5460A
CS5460A
DS487F5 25
or custom calibration board. When the metering
system is installed, the calibrator would be used to
control calibration and/or to program user-speci-
fied commands and calibration values into the EE-
PROM. The commands/data will determine the
CS5460A’s exact operation, when the auto-boot
initialization sequence is running. Any of the valid
commands can be used.
3.3.2 Auto-boot Data for EEPROM
This section illustrates what a typical set of code
would look like for an auto-boot sequence. This
code is what would be written into the EEPROM. In
the sequence below, the EEPROM is programmed
so that it will first send out commands that write cal-
ibration values to the calibration registers inside
the CS5460A. This is followed by the commands
used to set (write) the desired Pulse-Rate Register
value, and also to un-mask the ‘LSD’ status bit in
the Mask Register. Finally, the EEPROM code will
initiate ‘continuous computation cycles’ data acqui-
sition mode and select one of the alternate
pulse-output format s (e.g., set th e MECH bit in the
Control Register). The serial data for such a se-
quence is shown below in single-byte hexidecimal
notation:
40 00 00 61 ;Write to Configuration Regis-
ter, turn high-pass filters on,
set K = 1.
44 7F C4 A9 ;Write value of 0x7FC4A9 to
Current Channel Gain Regis-
ter.
46 7F B2 53 ;Write value of 0x7FB253 to
Voltage Channel DC Offset
Register.
4C 00 00 14 ;Set Pulse Rate Register to
0.625 Hz.
74 00 00 04 ;Unmask bit #2 (“LSD” bit in
the Mask Register).
E8 ;Start performing continuous
computation cycles.
78 00 01 40 ;Write STOP bit to Control
Register, to terminate au-
to-boot initialization se-
quence, and also set the
EOUT pulse output to Me-
chanical Counter Format.
This data from the EEPROM will drive the SDI pin
of the CS5460A during the auto-boot sequence.
The following sequence of events will cause the
CS5460A to execute the auto-boot mode initializa-
tion sequence: (A simple tim ing diagram for this se-
quence is shown below in Figure 14.) If the MODE
pin is set to logic high (or if the MODE pin was
set/tied to logic high during/after the CS5460A has
been powered on), then changing the RESET pin
from active state to inactive state (low to high) will
cause the CS 5460A to drive the CS pin low, and af-
ter this, to issue the standard EEPROM block-read
command on the CS54 60A’s SD O line. Once these
events have completed, the CS5460A will continue
to issue SCLK pulses, to accept data/commands
from the EEPROM. The serial port will become a
master-mode interface. For a more detailed timing
diagram, see Switching Characteristics (in Section
1.)
RES
CS
SCLK
SDO
SDI
EE Read Address 0
5460A Commands Stop
MODE
Figure 14. Timi ng Diagram for Auto-boot Sequence
CS5460A
26 DS487F5
3.3.3 Application Note AN225
For more information on Auto-boot mode, see the
AN225, “USING THE CS5460A AUTO-BOOT
MODE”.
3.4 Interrupt and Watchdog Timer
3.4.1 Interrupt
The INT pin is used to indicate that an event has
taken place in the CS5460A that (may) need atten-
tion. These events inform the meter system about
operation conditions and internal error conditions.
The INT signal is created by combining the Status
Register with the Mask Register. Whenever a bit in
the Status Regist er becomes active, and the corre-
sponding bit in the Mask Register is a logic 1, the
INT signal becomes active.
3.4.1.1 Clearing the Status Register
Unlike the other registers, the bits in the Status
Register can only be cleared (set to logic 0). Wh en
a word is written to the Status Register, any 1s in
the word will cause the corresponding bits in the
Status Register to be cleared. The other bits of the
Status Register remain unchanged. This allows the
clearing of particular bits in the register without
having to know the state of the other bits. This
mechanism is designed to facilitate handshaking
and to minimize the risk of losing events that ha-
ven’t been processed yet.
3.4.1.2 Typical use of the INT pin
The steps below show how interrupts can be han-
dled by the on-board MCU.
•Initialization:
Step I0 - All Status bits are cleared by writing
FFFFFF (Hex) into the Status Register.
Step I1 - The conditional bits which will be used
to generate interrupts are then written to logic
1 in the Mask Register.
Step I2 - Enable interrupts.
•Interrupt Handler Routine:
Step H0 - Read the Status Register.
Step H1 - Disable all interrupts.
Step H2 - Branch to the proper interrupt service
routine.
Step H3 - Clear the Status Register by writing
back the value read in step H0.
Step H4 - Re-enable interrupts.
Step H5 - Return from interrupt service routine.
This handshaking procedure insures that any
new interrupts activated between steps H0 and
H3 are not lost (cleared) by step H3.
3.4.1.3 INT Active State
The behavior of the INT pin is controlled by the SI1
and SI0 bits of the Configuration Register. The pin
can be active low (default), active high, active on a
return to logic 0 (pulse-low), or active on a return to
logic 1 (pulse-high).
If the interrupt output signal format is set for either
active-high or active-low assertion, the interrupt
condition is cleared when the bits of the Status
Register are returned to their inactive state. If the
interrupt output signal format is set for either
pulse-high or pulse-low, note that the duration of
the INT pulse will be at least one MCLK/K cycle, al-
though in some cases the pulse may last for 2
MCLK/K cycles.
3.4.1.4 Exceptions
The IC (Invalid Command) bit of the Status Regis-
ter can only be cleared by performing the port ini-
tialization sequence. This is also the only Status
Register bit that is active low.
To properly clear the WDT (Watch Dog Timer) bit
of the Status Register, first read the Energy Regis-
ter, then clear the bit in the Status Register.
3.4.2 Watch Dog Timer
The Watch Dog Timer (WDT) is provided as a
means of alerting the system that there is a poten-
tial breakdown in communication with the micro-
controller. By allowing the WDT to cause an
interrupt, a controller can be brought back, from
some unknown code space, into the proper code
for processing the data created by the converter.
The time-out is preprogrammed to approximately 5
seconds. The countdown restarts each time the
Energy Register is read. Under typical situations,
the Energy Register is read every se cond. As a re-
sult, the WDT will not time out. Other applications
that use the watchdog timer will need to ensure
CS5460A
DS487F5 27
that the Energy Register is read at least once in ev-
ery 5 second span.
3.5 Oscillator Characteristics
XIN and XOUT are the input and output, respec-
tively, of an inverting amplifier to provide oscillation
and can be configured as an on -chip oscillator, as
shown in Figure 15. The oscillator circuit is de-
signed to work with a quartz crystal or a ceramic
resonator. To reduce circuit cost, two load capaci-
tors C1 are integrated in the device, one between
XIN and DGND, one between XOUT and DGND.
Lead lengths should be minimized to reduce stray
capacitance.
To drive the device from an external clock source,
XOUT should be left unconnected while XIN is
driven by the external circuitry. There is an amplifi-
er between XIN and the digital section which pro-
vides CMOS level signals. This amplifier works
with sinusoidal inputs so there are no problems
with slow edge times.
The CS5460A can be driven by a clock ranging
from 2.5 to 20 MHz. The K divider must be set to
the appropriate value such th at MCLK/K will be be-
tween 2.5 MHz and 5 MHz. The K divider value is
set with the K[3:0] bits in the Configuration Regis-
ter. As an example, if XIN = MCLK = 15 MHz, and
K is set to 5, then MCLK/K = 3 MHz, which is a val-
id value for MCLK/K. Note that if the K[3:0] bit s are
all set to zero, the value of the K divider value is 16.
3.6 Analog Inputs
The CS5460A accommodates a full-scale differen-
tial input voltage range of ±250 mV on both input
channels. (If the PGA setting on the current chan-
nel is set for the 50x gain setting inste ad of the 10x
gain setting, then the differential full-scale input
range on the current channel reduces to ±50 mV.)
System calibration can be used to increase or de-
crease the full scale span of the converter as long
as the calibration register values stay within the
limits specified. See Section 3.8, Calibration, for
more details.
3.7 Voltage Reference
The CS5460A is specified for operation with a
+2.5 V reference between the VREFIN and VA-
pins. A reference voltage must be supplied to the
VREFIN pin for proper operation of the two ADCs.
The CS5460A includes an internal 2.5 V reference,
available on the VREFOUT pin, that can be used
as the reference input voltage by connecting the
VREFOUT pin to the VREFIN pin. If lower temper-
ature drift is desired, an external reference can be
used; in which case the VREFOUT pin should be
left unconnected.
3.8 Calibration
3.8.1 Overview of Calibration Process
The CS5460A offers digital calibration. Each cali-
bration sequence will be executed by se tting/clear-
ing one or more of the 8 bits in the calibration
command word. For both channels, there are cal-
ibration sequences for both AC and DC purposes.
Regardless of whether an AC or DC calibration se-
quence is desired, there are two basic types of cal-
ibrations: system offset and system gain. During
the calibration sequences, proper input calibra-
tion signals to the “+” and “-” pins of the volt-
age-/current-channel inputs must be supplied.
These input calibration signals represent
full-scale levels (for gain calibrations) and ground
input levels (for offset calibrations).
The AC and DC calibration sequences are differ-
ent. Depending on the specific metering applica-
tion and accuracy requirements, some or all of the
calibration sequences may not be executed. (This
Oscillator
Circuit
DGND
XIN
XOUT
C1
C1 = 22 pF
C2
C2 =
Figure 15. Oscillator Connection
CS5460A
28 DS487F5
is explained in more detail in the following para-
graphs).
3.8.2 The Calibration Registers
Refer to Figure 3 and Figure 21.
Voltage Channel DC Offset Register and Cur-
rent Channel DC Offset Register - Store additive
correction values that are used to correct for DC
offsets which may be present on the voltage/cur-
rent channels within the entire meter system.
These registers are updated by the CS5460A after
a DC offset calibration sequence has been execut-
ed.
Voltage Channel Gain Register and Current
Channel Gain Register - Store the multiplicative
correction values determined by the full-scale gain
calibration signals that are applied to the meter’s
voltage/current channels. These registers are up-
dated by the CS5460A after either an AC or DC
gain calibration sequence has been executed.
Voltage Channel AC Offset Register and Cur-
rent Channel AC Offset Register - Store additive
offset correction values that are used to correct for
AC offsets which may be created on the volt-
age/current channels within the entire meter sys-
tem. Although a noise signal may have an average
value of zero [no DC offset] the noise may still have
a non-zero rms value, which can add an undesir-
able offset in the CS5460A’s Irms and Vrms re-
sults. These registers are updated by the
CS5460A after an AC offset calibration sequence
has been executed.
Referring to Figure 3, one should note that the AC
offset registers affect the output results differently
than the DC offset registers. The DC offset values
are applied to the voltage/current signals very early
in the signal path; the DC offset register value af-
fects all CS5460A results. This is not true for the
AC offset correction. The AC offset registers only
affect the results of the rms-voltage/rms-current
calculations.
Referring to Figure 3, the reader should note that
there are separate calibration regi sters for the AC
and DC offset corrections (for each channel). This
is not true for gain corrections, as there is only one
gain register per channel--AC and DC g ain calibra-
tion results are stored in the same reg ister. The re-
sults in the gain registers reflect either the AC or
DC gain calibration results, whichever was per-
formed most recently. Therefore, both a DC and
AC offset can be applied to a channel at the same
time, but only one gain calibration can be applied
to each channel. Either AC or DC gain calibration
can be used, but not both.
For both the voltage channel a nd the current chan-
nel, while the AC offset calibration sequence per-
forms an entirely different function than the DC
offset calibration sequence, the AC gain and DC
gain calibration sequences perform the same func-
tion (but they ac complish the fu nction u sing di ffer-
ent techniques).
Sin c e both the volta ge and curren t channels have
separate offset and gain register s associated with
them, system offset or system gain can be per-
formed on either channel without the calibration
results from one chan nel affecting the other.
3.8.3 Calibration Sequence
1. The CS5460A must be operating in its active
state, and ready to accept valid commands via th e
SPI interface, before a calibration sequence can
be executed. Clearing the ‘DRDY’ bit in the Status
Register is also recommended.
2. Apply appropriate calibration signal(s) to the “+”
and “-” signals of the voltage/current channel input
pairs. (The appropriate calibration signals for each
type of calibration sequence are discussed next, in
Sections 3.8.4 and 3.8.5.). The recommended se-
quence of calibration, if both gain and offset cali-
bration are required, is to run offset calibration
before gain calibration; and if both AC and DC off-
set calibration are required, DC offset should be
calibrated first.
3. Next send the 8-bit calibration command to the
CS5460A serial interface.
4. After the CS5460A has finished running the de-
sired internal calibration sequence and has stored
the updated calibration results in the appropriate
calibration registers, the DRDY bit is set in the Sta-
tus Register to indicate that the calibration se-
quence has been completed. If desired, the results
of the calibration can now be read from the appro-
priate gain/offset registers, via the serial port.
CS5460A
DS487F5 29
Note that when the calibration command is sent to
the CS5460A, the device must not be performing
A/D conversions (in either of the two acquisitions
modes). If the CS5460A is running A/D conver-
sions/computations in the ‘continuous computation
cycles’ acquisition mode (C = 1), the Pow-
er-Up/Halt Command must be issued first to termi-
nate A/D conversions/computations. If the
CS5460A is running A/D conversions/computa-
tions in the ‘single computation cycle’ data acquisi-
tion mode (C = 0), the Power-Up/Halt Command
must be issued first (unless the computation cycle
has completed) before executing any calibration
sequence. The calibration sequences will not run
if the CS5460A is running in either of the two avail-
able acquisition modes.
3.8.4 Calibration Signal Input Level
For both the voltage and current channels, the dif-
ferential voltage levels of the calibration signals
must be within the specified voltage input limits (re-
fer to “Differential Input Voltage Range” in Section
1., Characteristics & Specifications). For the volt-
age channel the peak differential voltage level can
never be more than 500 mVP-P. The same is true
for the current channel if the current channel input
PGA is set for 10x gain. If the the current channel’s
PGA gain is set to 50x, then the current channel’s
input limits are 100 mVP-P.
Note that for the AC/DC gain calibrations, there is
an absolute limit on the RMS/DC voltage levels (re-
spectively) that are selected for the voltage/current
channel gain calibration input signals. The maxi-
mum value that the gain register can attain is 4.
Therefore, for either chan nel, if the voltag e level of
a gain calibration input signal is low enough that it
causes the CS5460A to attempt to set either gain
register higher than 4, the gain calibration result
will be invalid, and after this occurs, all CS5460A
results obtained when the part is running A/D con-
versions will be invalid.
3.8.5 Calibration Signal Frequency
The frequency of the calibration signals must be
less than 1 kHz (assume MCLK/K = 4.096 MHz
and K = 1). Optimally, the frequency of the calibra-
tion signal will be at the same frequency as the fun-
damental power line frequency of the power
system that is to be metered.
3.8.6 Input Configurations for Calibrations
Figure 16 shows the basic setup for gain calibra-
tion. If a DC gain calibration is desired, a positive
DC voltage level must be applied, such that it truly
represents the absolute maximum peak instanta-
neous voltage level that needs to be measured
across the inputs (including the maximum
over-range level that must be accurately mea-
sured). In other words, the input signal must be a
positive DC voltage level that represents the de-
sired absolute peak full-scale value. However, in
many practical power metering situations, an AC
signal is preferred over a DC sig nal to calibrate the
gain. To perform AC gain calibration instead of DC,
an AC reference signal should be applied that is
set to the desired maximum RMS level. Because
the voltage/current waveforms that must be mea-
sured in most power systems are a pproximately si-
nusoidal in nature, the RMS levels of the AC gain
calibration input signals may need to be set signif-
icantly lower than the voltage/current channel’s
maximum DC voltage input level. This must be
done in order to avoid the possibility that the peak
values of the AC waveforms that are to be mea-
sured will not register a value that would be outside
the available output code rang e of the volt age/cur-
rent A/D converters. For example, on the voltage
channel, if the Voltage Channel Gain Register is
set to it’s default power-on value of 1.000... before
calibration, then the largest pure sinusoidal wave-
form that can be used in AC calibration is one
whose RMS-value is ~0.7071 of the value of the
voltage channel’s peak DC input voltage value of
500 mVP-P. Thus the maximum value of the input
sinusoid would be ~176.78 mV (rms). But in many
practical power metering situations, the RMS volt-
age input level of the AC gain calibration signal
may be reduced even further, to allow for some
over-ranging capability. A typical sinusoidal cali-
bration value which allows for reasonable
over-range margin would be 0.6 of the voltage/cur-
rent channel’s maximum input voltage level. For
the voltage channel, such a sine-wave would have
a value of 0.6 x 250 mVrms =150mV
rms.
For the offset calibrations, there is no difference
between the AC and DC calibration signals that
must be supplied: simply connect the “+” and “-’
CS5460A
30 DS487F5
pins of the voltage/current channels to their ground
reference level. (See Figure 17.)
Offset and gain calibration cannot be done at the
same time. This will cause undesirable calibration
results.
3.8.7 Description of Calibration Algo-
rithms
The computational flow of the CS5460A’s AC and
DC gain/offset calibration sequences are illustrat-
ed in Figure 18. This figure applies to both the volt-
age channel and the current channel. The
following descriptions of calibration sequences will
focus on the voltage channel, but apply equally to
the current channel.
Note: For proper calibration, it is assumed that the value
of the Voltage-/Current-Channel Gain Registers
are set to default (1.0) before running the gain
calibration(s), and the value in the
Voltage-/Current Channel AC and DC Offset
Registers is set to default (0) before running
calibrations. This can be accomplished by a
software or hardware reset of the device. The
values in the voltage/current calib ration registers
do affect the results of the calibration sequences.
3.8.7.1 AC Offset Calibration Sequence
The idea of the AC offset calibration is to obtain an
offset value that reflects the square of the RMS
output level when the inputs are grounded. During
normal operation, when the CS5460A is calculat-
ing the latest result for the RMS Voltage Register,
this AC offset register value will be sub tracted from
the square of each successive voltage sample in
order to nullify the AC offset that may be inherent
in the voltage-channel signal path. Note that the
value in the AC offset register is proportional to the
square of the AC offset.
First, the inputs are grounded, and then the AC off-
set calibration command is sent to the CS5460A.
When the AC offset calibration sequence is initiat-
ed, a valid RMS Voltage Register value is acquire d
and squared. This value is then subtracted from
the square of each voltage sample that comes
through the RMS data path. See Figure 18.
+
-
XGAIN
+
-
External
Connections
+
-
AIN+
AIN-
CM
+
-
Full Scale
(DC or AC)
Figure 16. System Calibration of Gain.
+
-
XGAIN
+
-
External
Connections
0V
+
-AIN+
AIN-
CM
+
-
Figure 17. System Calibration of Offset.
In Modulator
+
x
to V*, I*, P*, E* Registers
Filter
N
VRMS
N
SINC
DC Offset* Gain*
+
X
2
-X
1
x
N
AC Offset*
X
2
0.6
x
++
-+
2
*
* Denotes readable/writable register
X
N
Figure 18. Calibration Data Flow
CS5460A
DS487F5 31
3.8.7.2 DC Offset Calibration Sequence
The Voltage Channel DC Offset Register holds the
negative of the simple average of N samples taken
while the DC voltage offset calibration was execut-
ed. The inputs should be grounded during DC off-
set calibration. The DC offset value is added to the
signal path to nullify the DC offset in the system.
3.8.7.3 AC Gain Calibration Sequence
The AC voltage gain calibration algorithm attempts
to adjust the Voltage Channel Gain Register value
such that the calibration reference signa l level pre-
sented at the voltage inputs will result in a value of
0.6 in the RMS Voltage Register. The AC calibra-
tion signal is applied to the “+” and “-” input pins of
the channel under calibration. During AC voltage
gain calibration, the value in the RMS Voltage Reg-
ister is divided into 0.6. This result is the AC gain
calibration value stored in the Voltage Channel
Gain Register.
3.8.7.4 DC Gain Calibration Sequence
Based on the level of the positive DC calibration
voltage that should be applied across the “+” and
“-” inputs, the CS5460A determines the Voltage
Channel Gain Register value by averaging the In-
stantaneous Voltage Register’s output signal val-
ues over one computation cycle (N samples) and
then dividing this average into 1. Therefore, after
the DC voltage gain calibration has been executed,
the Instantaneous Voltage Register will read
full-scale whenever the DC level of the input signal
is equal to the level of the DC calibration signal that
was applied to the voltage channel inputs during
the DC gain calibration. Fo r example, if a +230 mV
DC signal is applied to the voltage channel inputs
during the DC gain calibration for the curre nt chan-
nel, then the Instantaneous Voltage Register will
measure unity whenever a 230 mV DC level is ap-
plied to the voltage channel inputs.
3.8.8 Duration of Calibration Sequence
The value of the Cycle Count Register (N) deter-
mines the number of conversions that will be per-
formed by the CS5460A during a given calibration
sequence. For DC offset/gain calibrations, the cal-
ibration sequence always takes at least N + 30
conversion cycles to complete. For AC offset/gain
calibrations, the calibration sequence takes at
least 6N + 30 A/D conversion cycles to complete,
(about 6 computation cycles). If N is in creased, the
accuracy of calibration results will increase.
For more information on Calibration, see AN227,
“CALIBRATING THE CS5460A”.
3.9 Phase Compensation
The values of bits 23 to 17 in the Configuration
Register can be altered to adjust the amount of
time delay that is imposed on the digitally sample d
voltage channel signal. This time delay is applied
to the voltage channel signal in order to compen-
sate for the relative phase delay (with respect to
the fundamental frequency) between the sensed
voltage and current signals. Voltage and current
transformers, as well as other sensor/filter/protec-
tion devices deployed at the front-end of the volt-
age/current sensor networks can often introduce a
phase-delay in the system that distorts/corrupts
the phase relationship between the line-voltage
and line-current signals that are to be measured.
The phase compensation bits PC[6:0] in the Con-
figuration Register can be set to nullify this undesir-
able phase distortion between the digitally
sampled signals in the two channels. The value in
the 7-bit phase compensation word indicates the
amount of time delay that is imposed on the volt-
V
RMS
Register =
230
/
250
x
1
/
2
0.65054
250 mV
230 mV
0 V
-230 mV
-250 mV
0.9999...
0.92
-0.92
-1.0000...
V
RMS
Register =
0.6000...
250 mV
230 mV
0 V
-230 mV
-250 mV
0.84853
-0.84853
Before AC Gain Calibration (Vgain Register = 1)
After AC Gain Calibration (Vgain Register changed to ~0.9223)
Instantaneous Voltage
Register Values
Instantaneous Voltage
Register Values
Sinewave
Sinewave
0.92231
-0.92231
INPUT
SIGNAL
INPUT
SIGNAL
Figure 19. Example of AC Gain Calibration
CS5460A
32 DS487F5
age channel’s analog input signal with respect to
the current channel’s analog input signal.
With the default setting, the phase delay on the
voltage channel signal is ~0.995 µs (~0.0215 de-
grees assuming a 60 Hz power signal). With
MCLK = 4.096 MHz and K = 1, the range of the in-
ternal phase compensation ranges from
-2.8 degrees to +2.8 degrees when the input volt-
age/current signals are at 60 Hz. In this condition,
each step of the phase compensation register (val-
ue of one LSB) is ~0.04 degrees. For values of
MCLK other than 4.096 MHz, these values for the
span (-2.8 to +2.8 degrees) and for the step size
(0.04 degrees) should be scaled by
4.096 MHz / (MCLK / K). For power line frequen-
cies other than 60Hz (e.g., 50 Hz), the values of
the range and step size of the PC[6:0] bits can be
determined by converting the above values to
time-domain (seconds), and then computing the
new range and step size (in degrees) with respect
to the new line frequency.
Unlike offset/gain calibration, the CS5460A does
not provide an automated on-chip phase calibra-
tion sequence. To calibrate the phase delay, the
phase compensation bits can be adjusted while the
CS5460A is running in ‘continuous computation
cycles’ data acquisition mode. For example, the
CS5460A can be set up to perform continuous
computations on a purely resistive load (no induc-
tance or capacitance). The PC[6:0] bits can then
be adjusted until the Energy Register value is max-
imized.
3.10 Time-Base Calibration Register
The Time-Base Calibration Register (notated as
“TBC” in Figure 3) is used to compensate for slight
errors in the XIN input frequency. External oscilla-
tors and crystals have certain tolerances. If there is
a concern about improving the accuracy of the
clock for energy measurements, the Time-Base
Calibration Register value can be manipulated to
compensate for the frequency error. Note from Fig-
ure 3 that the TBC Register only affects the value
in the Energy Register.
As an example, if the desired XIN frequency is
4.096 MHz, but during production-level testing,
suppose that the average frequency of the crystal
on a particular board is measured to actually be
4.091 MHz. The ratio of the desired frequency to
the actual frequency is 4.096 MHz/4.091 MHz =
~1.00122219506. The TBC Register can be set to
1.00122213364 = 0x80280C(h), which is very
close to the desired ratio.
3.11 Power Offset Register
Referring to Figure 3, note the “Poff” Register that
appears just after the power computation. This reg-
ister can be used to offset system power sources
that may be resident in the system, but do not orig-
inate from the power line signal. These sources of
extra energy in the system contribute undesirable
and false offsets to the power/energy measure-
ment results. For example, even after DC offset
and AC offset calibrations have been run on each
channel, when a voltage signal is applied to the
voltage channel inputs and the current channel is
grounded (i.e., there is zero input on the current
channel), the current channel may still register a
very small amount of RMS current caused by leak-
age of the voltage channel input signal into the cur-
rent channel input signal path. Although the
CS5460A has high channel-to-channel crosstalk
rejection, such crosstalk may not totally be elimi-
nated.) If the amount of ‘artificial’ power that might
be induced into the voltage/current channel signals
due to such crosstalk/system noise/etc. can be de-
termined, then the Power Offset Register can be
programmed to nullify the effects of this unwanted
energy.
3.12 Input Protection - Current Limit
In Figures 6, 7, 8, and 9, note the series resistor RI+
which is connected to the IIN+ input pin. This resis-
tor serves two purposes. First, this resistor func-
tions in coordination with CIdiff and/or CIdiff to form a
low-pass filter. The filter will a) remove any broad-
band noise that is far outside of the frequency
range of interest, and also b) this filter serves as
the anti-aliasing filter, which is necessary to pre-
vent the A/D converter from receiving in put signals
whose frequency is higher than one-half of the
sampling frequency (the Nyquist frequency). The
second purpose of this resistor is to provide cur-
rent-limit protection for the Iin+ input pin, in the
event of a power surge or lightning su rge. The role
that RI+ contributes to input filtering will be dis-
cussed in the Section 3.13. But first the current-lim-
it protection requirements for the Iin+/Iin- and
Vin+/Vin- pins are discussed.
CS5460A
DS487F5 33
The voltage/current-channel inputs have
surge-current limits of 100 mA. This applies to brief
voltage/current spikes (<250 ms). The limit is
10 mA for DC input overload situations. To prevent
permanent damage to the CS5460A, the designer
must include adequate protection circuitry in the
power meter design, to insure that these pin cur-
rent limits are never exceeded, when CS5460A is
operating in the intended power-line metering envi-
ronment.
Focusing specifically on Figure 7, which shows
how voltage/current transformers can be used to
sense the line-voltage/line-current, suppose for ex-
ample that the requirements for a certain 120 VAC
power system require that the power meter must
be able to withstand up to a 8 kV voltage spike on
the power line during normal operating conditions.
To provide a suitable sensor voltage input level to
the voltage channel input pins of the CS5460A, the
turns ratio of the voltage-sense transformer shou ld
be chosen such that the ratio is, for example, on
the order of 1000:1. A voltage-sense transformer
with a 1000:1 turns ratio will provide a 120 mV
(rms) signal to the CS5460A’s differential voltage
channel inputs, when the power line voltage is at
the nominal level of 120 VAC. Therefore, a brief
8 kV surge would be reduced to a 8 V surge across
RV+.
What happens when 8 volts (common-mode) is
present across one of the analog input pins of the
CS5460A? The Vin+/Vin- and Iin+/Iin- pins of the
CS5460A are equipped with internal protection di-
odes. If a voltage is presented to any of these pins
that is larger than approximately 7 V (with respect
to VA- pin) these protection diodes will turn on in-
side the CS5460A. But in order to prevent exces-
sive current levels from flowing throug h the device,
the value of RV+ must be large enough that when a
8V surge is present across the secondaries of the
voltage-sense transformer, the brief surge current
through RV+ should not be any greater than
100 mA. Therefore, a minimum value for RV+
would be (8 V - 7 V) / 100 mA = 10 . This value
may be increased as needed, to easily obtain the
desired cutoff frequency of the anti-aliasing filter on
the voltage channel (described later), and also to
provide some margin. But the designer should try
to avoid using values for the protection resistors
that are excessively high. A typical value for RV+
would be 470 .
The VIN- pin should also have a pro tection resistor
(called RV- in Figure 7). To maintain symmetry, the
value of RV- should be made equal to RV+.
For the current channel inputs (Iin+ and Iin-), if the
maximum current rating (Imax) for this power line is
30 A (RMS), then a suitable turns ratio for the cur-
rent-sense transformer might be 200:1. Since the
maximum load for a 120 VAC line rated at 30 A
would be 4 (for unity power factor), a brief 8 kV
surge across “L” and “N” could generate as much
as 2000 A (RMS) of current through the primaries
of the current-sense transformer. This can in turn
generate as much as 10 V across the secondaries
of the current-sense transformer. This voltage is
high enough to turn on one or more of the internal
protection diodes located off of the Iin+/Iin- pins.
Therefore, the value of the protection resistor that
will limit the current flow to less than 100 mA would
be (10 V - 7 V) / 100 mA = 30 . In order to pro-
vide some margin and to use the same resistor val-
ues that are used on the Vin+/Vin- pins, a 470
resistor can be used as a lower limit for t he RI+ and
RI- resistors shown in Figure 7.
Referring to the circuit implementations shown in
Figures 6, 8, and 9, note that when resistor-divider
configurations are used to provide the voltage
channel sense voltage, the VIN+ pin does not need
an additional, separate, dedica ted protection resis-
tor. This is because the resistive voltage-divider a l-
ready provides the series resistance that is needed
for this protection resistance (from R1 and R2).
(And note in Figure 8 that this is true for both the
VIN+ pin and the VIN- pin.) In Figure 7, a voltage
transformer is used as the voltage sensor. When
any type of transformer is used as the sensor de-
vice for voltage (or current) channel, a dedicated
protection resistor RV+ should be installed in series
with the VIN+ pin, and similarly, a resistor (RV-)
should be installed in series to the VIN- input pin.
Additional considerations/techniques regarding
the protection of the analog inpu t pins against sud-
den high-frequency, high-level voltage/current
surges are discussed in Section 3.14.
CS5460A
34 DS487F5
3.13 Input Filtering
Figure 6 shows how the analog inputs can be con-
nected for a single-ended input configuration. Note
here that the Vin- and Iin- input pins are held at a
constant DC common-mode level, and the varia-
tion of the differential input signal occurs only on
the Vin+ and Vin- pins. The common-mode level
on the Vin-/Iin- pins is often set at (or very near) the
CS5460A’s common-mode ground reference po-
tential. (The common-mode ground reference po-
tential is defined by the voltage at the VA- pin.)
But this is not required--the DC reference level of
the Vin-/Iin- pins can be set to any potential be-
tween [VA-] and [(VA+) - 250 mV]. In Figure 6, ob-
serve the circuitry which has been placed in front
of the current channel input pins, as one example.
The anti-aliasing filter can be constructed by calcu-
lating appropriate values for RI+ =RI-, CIdiff, and
CI+ = CI-. The sensor voltage that is created by the
voltage drop across RSHUNT is fed int o the Iin+ pin,
while the voltage at the Iin- pin is held constant.
Figure 7 shows a differential bipolar input configu-
ration. Note in Figure 7 that the “+” and “-” input
pins for the voltage/current channels are equally
referenced above and below the CS5460A’s
ground reference voltage. Such a differential bipo-
lar input configuration can be used because the
CS5460A voltage/current channel inputs are able
to accept input voltage levels as low as -250 mV
(common-mode) below the VA- pin ground refer-
ence, which is defined by the voltage at the VA-
pin. (In fact, if desired, the center-tapped reference
of these differential input pairs could be connected
to a DC voltage of, for example, +2 V, because
+2 V is within the available common-mode range
of [VA-] and [VA+ - 250mV]. But this configuration
may not be practical for most metering applica-
tions.) In the differential b ipolar input configuration,
the voltage signals at the Vin- and Iin- pins will fluc-
tuate in similar fashion to the Vin+/Iin+ pins, except
the voltages at the “-” pins will be 180 degrees out
of phase with respect to the voltage signals at the
“+” pins. Therefore the signal paths to the “+” and
“-” pins play an equal role in defining the differential
voltage input signal. Because of this, the protection
resistors placed on Vin-/Iin- pins will play an equal-
ly important role as the resistors on the Vin+/Iin+
pins, in defining the differential responses of the
voltage/current channel input anti-aliasing filters.
These resistors also serve as the curren t-limit pro-
tection resistors (mentioned earlier).
Before determining a typical set of values for RV+,
RV-, CV+, CV-, CVdiff, RI+, RI-, CI+, CI-, and CIdiff in
Figure 7, several other factors should be consid-
ered:
1. Values for the above resistors/capacitors should
be chosen with the desired differential-mode (and
common-mode) lowpass cutoff frequencies in
mind. In general, the differential cutoff frequencies
should not be less than 10 times the cut-off fre-
quencies of the internal voltage/current chann el fil-
ters, which can be estimated by studying Figure 4
and Figure 5. In these figures, the internal voltage
channel cutoff frequency is ~1400 Hz while the
current channel cutoff frequency is ~1600 Hz. If
the cutoff frequency of the external anti-aliasing fil-
ter is much less than 10x these values (14000 Hz
and 16000 Hz), then some of the harmonic content
that may be present in the voltage/current signals
will be attenuated by the voltage/current channel
input anti-aliasing filters, because such R-C filters
will begin to roll off at a frequency of 1/10th of the
filter’s -3 dB cutoff frequency. If the designer is not
interested in metering energy that may be present
in the higher harmonics (with respect to the fund a-
mental power line frequency) then the differen-
tial-mode cutoff frequencies on the voltage /current
input networks can be reduced. However, relaxing
the metering bandwidth is usually unacceptable,
as most modern power meters are requ ired to reg-
ister energy out to the 11th harmonic (at a mini-
mum).
2. The first-order time-constants of t he overall volt-
age and current channel sensor networks should
be set such that they are equal (within reason), or
at least close in magnitude. If the time-co nstants of
the voltage/current sensor networks are not
well-matched, then the phase relationship be-
tween the voltage-sense and current-sense sig-
nals will suffer an undesirable shift. In this
situation, the real (true) power/energy measure-
ments reported by the CS5460A can contain signif-
icant error, because the power factor of the sensed
voltage and current signals will be significantly dif-
ferent than the actual power factor of the power
line voltage/current waveforms.
CS5460A
DS487F5 35
Note also that in addition to the time-constants of
the input R-C filters, the phase-shifting properties
of the voltage/current sensors devices may also
contribute to the overall time-constants of the volt-
age/current input sensor networks. For example,
current-sense transformers and potential trans-
formers can impose phase-shifts on the sensed
current/voltage waveforms. Therefore, this possi-
ble source of additional phase-shift caused by sen-
sor devices may also need to be considered while
selecting the final R and C values for the volt-
age/current anti-aliasing filters. As an alternative
to, or in addition to the fine adjustment of the R and
C values of the two anti-alias filters, the CS5460A’s
phase compensation bits (see Phase Compensa-
tion) can also be adjusted, in order to more closely
match the overall time-constants of the volt-
age/current input networks. Regardless of whe ther
the phase compe nsation bits are or are not used to
help more closely match the time-constants, this
requirement of equal time-constants must ulti-
mately be considered when selecting the final R
and C values that will be used for the input filters.
(Of course, this factor may not turn out to be so im-
portant if the designer is confident that the
mis-match between the voltage/current channel
time-constants will not cause enough error to vio-
late the accuracy requirements for the given pow-
er/energy metering application.)
3. Referring to the specs in Section 1, note that the
differential input impedance across the current
channel input pins is only 30 k, which is signifi-
cantly less than the corresponding impedance
across the voltage channel input pins (which is
1M). While the impedance across the voltage
channel is usually high enough to be ignored, the
impedance across the current channel inputs may
need to be taken into account by the designer
when the desired cutoff frequencies of the filters
(and the time-constants of the overall input net-
works) are computed. Also, because of this rather
low input impedance across the current channel in-
puts, the designer should note that as the values
for RI+ and/or RI- are increased, the interaction of
the current channel’s input impedance can begin to
cause a significant voltage drop within the current
channel input network. If this is not taken into ac-
count, values may be chosen for RI+ =RI- that are
large enough to cause a discrepancy between the
expected (theoretical) sensor gain and the actual
sensor gain of the current sensor network, which
may not be anticipated by the designer. Also, if this
voltage drop effect is not considered, the designer
may select values for RI+ and RI that are slightly
larger than they should be, in terms of maximizing
the available dynamic range o f the current channel
input. For the very same reason, the line-cur-
rent-to-sensor-output-voltage conversion factor of
the current sensor may not be optimized if this volt-
age division is not considered, when (for exa mple)
selecting a value for the bu rden resistor for a given
current transformer. This issue should be consid-
ered, although a slight voltage drop only causes a
slight loss in available dynamic range, and the ef-
fects of this voltage drop on the actual current
channel sensor gain can be removed during gain
calibration of the current channel.
4. Referring to Figures 6 - 9, not all of the capaci-
tors/resistors shown in these example circuit dia-
grams are necessary; however, note that the all of
the filter capacitors (CV+, CV-, CI+, CI-, CVdiff, and CI-
diff) can, in some situations, help to improve the
ability of both input networks to attenuate very
high-frequency RFI that can enter into the
CS5460A’s analog input pins. Therefore, during
layout of the PCB, these capacitors should be
placed in close proximity to their respective input
pins.
If any/all of the common-mode connected capaci-
tors (CV+, CV-, CI+, CI-) are included in the input net-
works, their values should be selected such that
they are at least one order of magnitude smaller
than the value of the differential capacitors (CVdiff,
and CIdiff). This is done for at least two reasons:
a) The value tolerance for most types of commer-
cially available surface-mount capacitors is not
small enough to insure appreciable value match-
ing, between the value of CV+ vs. CV-, as well as
between the value of CV+ vs. CV-. Such value mis-
match can adversely affect the desired differen-
tial-mode response of the voltage/current input
networks. By keeping the values of these com-
mon-mode capacitors small, and allowing the val-
ue of the CVdiff, and CIdiff to dominate the
differential 1st-order time-constant of the input filter
networks, this undesirable possibility of frequency
response variation can be minimized.
CS5460A
36 DS487F5
b) The common-mode rejection performance of the
CS5460A is sufficient within the frequency range
over which the CS5460A performs A/D conver-
sions. Addition of such common-mode caps can
actually often degrade the common-mode rejec-
tion performance of the entire voltage/current input
networks. Therefore, cho osing rela tive ly small va l-
ues for (CV+, CV-, CI+, CI-) will provide necessary
common-mode rejection at the much higher fre-
quencies, and will allow the CS5460A to realize its
CMRR performance in the frequency-range of in-
terest.
[Note that this discussion does not include correc-
tion of phase-shifts caused by the voltage-sense
transformer and current-sense transformer, al-
though these phase-shifts should definitely be con-
sidered in a real-life practical meter design.] On the
current channel, using commonly available values
for the components, RI+ and RI- can be set to
470 . Then a value of CIdiff = 18 nF and a value of
0.22 nF for CI- and CI- will yield a -3 dB cutoff fre-
quency of 15341 Hz for the current channel. For
the voltage channel, if RI+ and RI- are also set to
470 , CVdiff = 18 nF, and CV- =CV- =0.22nF
(same as current channel), the -3 dB cutoff fre-
quency of the voltage channel’s input filter will be
14870 Hz. The difference in the two cutoff frequen-
cies is due to the difference in th e input impedance
between the voltage/current channels.
If there is concern about the effect that the differ-
ence in these two cutoff frequencies (and therefore
the mis-match between the time-constants of the
overall voltage/current input networks) would have
on the accuracy of the power/energy registration, a
non-standard resistor value for RV+ =RV- of (for ex-
ample) 455 can be used. This would shift the
(differential) -3 dB cutoff frequency of the voltage
channel’s input filter (at the voltage channel inputs)
to ~15370 Hz, which would cause the first-order
time-constants of the voltage/current channel input
filters to be closer in value.
Agreement between the voltage/current channel
time-constants can also be obtained by adjusting
the phase compensation bits, instead of using less
commonly-available resistor/capacitor values
(such as RI+ =RI- = 455 ). If the values of RI+ and
RI- are again 470 , the first-order time-constants
of the two R-C filters are estimated by taking the re-
ciprocal of the -3 dB cutoff frequencies (when ex-
pressed in rads/s). Subtracting these two
time-constants shows that after the vo ltage/current
signals pass through their respective anti-aliasing
filters, the sensed voltage signal will be delayed
~0.329 µs more than the current signal. If metering
a 60 Hz power system, this implies that the input
voltage-sense signal will be delayed
~0.007 degrees more than the delay imposed on
the input current-sense signal. Note that when the
PC[6:0] bits are set to their default setting of
“0000000”, the internal filtering stages of the
CS5460A will impose an additional delay on the
fundamental frequency component of the 60Hz
voltage signal of 0.0215 degrees, with respect to
the current signal. The total difference between the
delay on the voltage-sense fundamental and the
current-sense fundamental will therefore be
~0.286 degrees. But if the phase compensation
bits are set to 1111111, the CS5460A will delay the
voltage channel signal by an additional -0.04 de-
grees, which is equivalent to shifting the voltage
signal forward by 0.04 degrees. The total phase
shift on the voltage-sense signal (with respect to
the fundamental frequency) would then be
~0.011 degrees ahead of the current-sense signal,
which would therefore provide more close-
ly-matched delay values between the volt-
age-sense and current-sense signals. Adjustment
of the PC[6:0] bits therefore can provide an effec-
tive way to more closely match the delays of the
voltage/current sensor signals, allowing for more
commonly available R and C component values to
be used in both of these filters.
As a final note, tolerances of the R and C compo-
nents that are used to build the two R-C filters
should also be taken into consideration. A com-
mon tolerance of ±0.1% can vary the delay by as
much as much as ~±2.07 µs, which means that the
difference between the delays of the voltage-sense
and current-sense signals that is caused by these
filters could vary by as much as ~±4.1 µs, which is
equivalent to a phase shift of ~±0.089 degrees (at
60 Hz). This in turn implies that our decision to ad-
just the PC[6:0] bits (to shift the voltage signal for-
ward by 0.04 degrees) could actually cause the
voltage signal to be shifted by as much as
~0.100 degrees ahead of the current signal.
Thus, adjustment of the PC[6:0 ] bits to more close-
ly match the two time-constants/delays may only
be useful if a precise calibration operation can be
CS5460A
DS487F5 37
performed on each individual power meter, during
final calibration/test of the meter.
3.14 Protection Against High-voltage
and/or High-current Surges
In many power distribution systems, it is very likely
that the power lines will occasiona lly carry brief but
large transient spikes of voltage/current. Two com-
mon sources of such high-energy disturbances are
1) a surge in the line during a lightning storm, o r 2)
a surge that is caused when a very inductive or ca-
pacitive load on the power line is suddenly turned
on (“inductive kick”). In these situations, the input
protection resistors and corresponding input filter
capacitors (discussed in the previous sections)
may not be sufficient to protect the CS5460A from
such high-frequency voltage/current surges. The
surges may still be strong enough to cause perma-
nent damage to the CS5460A. Because of this, the
designer should consid er adding certain additional
components within the voltage/current channel in-
put circuitry, which can help to protect the
CS5460A from being permanently damaged by the
surges.
Referring to Figure 20, the addition of capacitors
C1 and C2 can help to further attenuate these
high-frequency power surges, which can greatly
decrease the chances that the CS5460A will be
damaged. Typical values for C1 and C2 may be on
the order of 10 pF, although the exact value is re-
lated to the reactive and resistive properties of the
voltage and current sen sor devices. In addition, di-
odes D1 - D4 can help to quickly clamp a high volt-
age surge voltage presented across the
voltage/current inputs, before such a surge can
damage the CS5460A. An example of a suitable
diode part number for this application is BAV199,
which has the ability to turn on very quickly (very
small turn-on time). A fuse could potentially serve
this purpose as well (not shown). R3 and R4 can
provide protection on the “-” sides of the two input
pairs. Set R3 = R1 and R4 = R5. Finally, placing
50 resistors in series with the VA+ and VD+ pins
is another technique that has sometimes proven to
be effective in protecting the CS5460A from such
high-level, high-frequency voltage/current surges.
However, these 50 resistors may not be neces-
sary if the protection on the analog input channels
is sufficient, and this is not the most attractive so-
VA+ VD+
CS5460A
0.1 µF
100 µF
500
470 nF
500
N10
14
VIN+
9
VIN-
IIN-
10
15
16 IIN+
PFMON
CPUCLK
XOUT
XIN
RESET
17
2
1
24
19
CS
7
SDI
23
SDO
6
SCLK
5
INT
20
EDIR 22
EOUT 21
0.1 µF
VREFIN
12
VREFOUT
11
VA- DGND
13 4
3
0.1 µF
10 k
5 k
L
R
L
4.069 MHz
To Service
1 k
1 k
1 k
1 k
+5 V
+5 V
10 k 10 k 47 k 47 k20 k 20 k 1 k
SCLK
SDO
CS
INT
SDI
RST
GND
+5 V
5.1 Volt
1 k
120 Vrms
5050 For Input Surge
Protection To reduce
EMI susceptibility
D1 D2
D4
D3
R3
R4
C1
C2
R1R2
R
SHUNT
R5
C4
C5
C6 C7
C3
C8
MODE NC
8
NC
L3
L4
L1
L2
Figure 20. Input Protection for Single-Ended Input Configurations
Input protection for single-ended input configurations, using resistive
divider and current shunt resistor.
Note that the digital interface is isolated using opto-isolators.
CS5460A
38 DS487F5
lution, because these resistors will dissipate what
can be a significant amount of po wer, and they will
cause an undesirable voltage dro p which decreas-
es the voltage level presented to the VA+ and VD+
supply pins.
3.15 Improving RFI Immunity
During EMC acceptance testing of a power meter-
ing assembly, the performance of the CS5460A’s
A/D converters can be adversely affected b y exter-
nal radio frequency interference (RFI). Such exter-
nal RFI can be coupled into the copper traces
and/or wires on the PCB. If RFI is coupled into an y
of the traces which tie into the CS5460A’s
Vin+/Vin- or Iin+/Iin- input pins, then errors may be
present in the CS5460A’s power/energy registra-
tion results.
When such degradation in performance is detect-
ed, the CS5460A’s immunity to RF disturbance
may be improved by configuring the ‘+’ and ‘-’ in-
puts of the voltage/current channel inputs such that
they are more symmetrical. This is illustrated in
Figure 20 with the addition of resistors R3 and R4,
as well as capacitors C5 and C6. Note that the in-
put circuitry placed in front of the voltage/current
channel inputs in Figure 20 represents a sin-
gle-ended input configurations (for both channels).
Therefore, these extra resistors and components
may not necessarily be neede d to achieve the sim-
ple basic anti-aliasing filtering on the inputs. How-
ever, the addition of these extra components can
create more symmetry across the ‘+’ and ‘-’ inputs
of the voltage/current input channels, which can of-
ten help to reduce the CS5460A’s susceptibility to
RFI. The value of C5 should be the same as C3,
(and so the designer may have to re-calculate the
desired value of C3, since the addition of C5 will
change the overall differential-/common-mode fre-
quency responses of the input filter.) A similar ar-
gument can be made for the addition of C6 (to
match C8) on the current channel’s input filter. Fi-
nally, addition of capacitors C4 and C7 can also
sometimes help to improve CS5460A’s perfor-
mance in the presence of RFI. All of these input ca-
pacitors (C3 - C8) should be placed in very close
proximity to the ‘+’ and ‘-’ pins of the voltage/cur-
rent input pins in order to maximize their ability to
protect the input pins from high-frequency RFI. In
addition to or as an alternative to these capacitors,
addition of inductors L1 - L4 can sometimes help to
suppress any incoming RFI. Note that the addition-
al components just discussed can sometimes actu-
ally degrade the CS5460A’s immunity to RFI. The
exact configuration that works best can vary signif-
icantly, according to the exact PCB layout/orienta-
tion. Finally, note that inside the CS5460A, the
Vin+, Vin-, Iin+, and Iin- pins have all been buffered
with ~10 pF of internal capacitance (to VA-) in at-
tempt to improve the device’s immu nity to external
RFI.
3.16 PCB Layout
For optimal performance, the CS5460A should be
placed entirely over an analog ground plane with
both the VA- and DGND pins of the device con-
nected to the analog plane.
Note: Refer to the CDB5460A Evaluation Board for
suggested layout details, as well as
Applications Note 18 for more detailed layout
guidelines. Before layout, please call for our
Free Schematic Review Service.
4. SERIAL PORT OVERVIEW
The CS5460A's serial port incorporates a state
machine with transmit/receive buffers. The state
machine interprets 8 bit command words on the
rising edge of SCLK. Upon decoding of the com-
mand word, the state machine performs the re-
quested command or prepares for a data transfer
of the addressed register. Request for a read re-
quires an internal register transfer to the transmit
buffer, while a write waits until the completion of
24 SCLKs before performing a transfer. The inter-
nal registers are used to control the ADC's func-
tions. All registers are 24-bits in length. Figure 21,
in section 5, summarizes the internal registers
available.
The CS5460A is initialized and fully operational in
its active state upon power-on. After a power-on,
the device will wait to receive a valid command (the
first 8-bits clocked into the serial port). Upon re-
ceiving and decoding a valid command word, the
state machine instructs th e converter to eith er per-
form a system operation, o r transfer data to or from
an internal register.
CS5460A
DS487F5 39
4.1 Commands (Write Only)
All command words are 1 byte in leng th. Co mma nds that wr ite to a reg iste r mu st be follo wed b y 3 bytes of r egister
data. Commands that read from registers initiate the output of 3 bytes of register data. Commands that read data
can be ‘chained’ with other commands (e.g., while reading data, a ne w command ca n be sent to SDI which can ex-
ecute before the original read is completed). This allows for ‘chaining’ commands.
4.1.1 Start Conversions
This command indicates to th e state machine to be gin acquiring measurements and calculating results. The device
has two modes of acquisition.
Modes of acquisition/measurement
0 = Perform a single computation cycle
1 = Perform continuous computation cycles
4.1.2 SYNC0 Command
This command is th e e nd of the se rial port re-initialization sequence. It can al so be used as a NOP command . The
serial port is resynchronized to byte boundaries by sending three or more consecutive SYNC1 commands followed
by a SYNC0 command.
4.1.3 SYNC1 Command
This command is part of the serial port re-ini tialization sequence. It can also serve as a NOP command.
4.1.4 Power-Up/Halt
If the device is powered- down into either stand-by or sleep power savin g mode (See 4.1.5), this command will pow-
er-up the device. After the CS5460A is initially powered-on, no conversions/computations will be running. If the de-
vice is already powered on and the device is running either ‘single computation cycle’ or ‘continuous computation
cycles’ data acquisition modes, all computations will be halted once this command is received.
B7 B6 B5 B4 B3 B2 B1 B0
1110C000
B7 B6 B5 B4 B3 B2 B1 B0
11111110
B7 B6 B5 B4 B3 B2 B1 B0
11111111
B7 B6 B5 B4 B3 B2 B1 B0
10100000
CS5460A
40 DS487F5
4.1.5 Power-Down
The device has two power-do wn states to conserve power. If the chip is put in stand-by state, all circuitry except the
analog/digital clock gener ators is turned off. In the sleep state, a ll circuitry except the digital cloc k generator and the
instruction decoder is turned off. Waking up the CS5460A out of sleep state requires more time than waking the
device out of stand-by state, because of the extra time needed to re-start and re-stabilize the analog clock signal.
[S1 S]0 Power-down state
00 = Reserved
01 = Halt and enter stand - by po we r saving s tate . Th is stat e allo ws qu ick po we r- on time
10 = Halt and enter sleep power saving state. This state requires a slow power-on time
11 = Reserved
4.1.6 Calibration
The device has the capability of performing a system AC offset calibration, DC offset calibration, AC gain calibration,
and DC gain calibration. Calibration can be done on the voltage channel, the current channel, or both channels at
the same time. Offse t and gain calibrations sh ould NOT be performe d at the sa me time (must do one after the oth-
er). For a given ap plication, if DC gain calibrations are performed, then AC g ain calibration should not be perfor med
(and vice-versa ). The proper input voltages must be supplied to the device before initiating calibration.
[V I] Designates calibration channel
00 = Not allowed
01 = Calibrate the current channel
10 = Calibrate the voltage channel
11 = Calibrate voltage and current channel simultaneously
R Specifies AC calibration (R=1) or DC calibration (R=0)
G Designates gain calibration
0 = Normal operatio n
1 = Perform gain calibration
O Designates offset calibration
0 = Normal operatio n
1 = Perform offset calibration
B7 B6 B5 B4 B3 B2 B1 B0
1 0 0S1S00 0 0
B7 B6 B5 B4 B3 B2 B1 B0
110VIRGO
CS5460A
DS487F5 41
4.1.7 Register Read/Write
This command inform s the state machine that a reg ister access is required. On reads the addr essed register is load-
ed into the output buffer and clocked out by SCLK. On writes the data is clocked into the input buffer and transferred
to the addressed register on the 24th SCLK.
W/R Write/Read control
0 = Read register
1 = Write register
RA[4:0] Register address bits. Binary encoded 0 to 31. All registers are 24 bits in length.
Address Abbreviation Name/Description
00000 Config Configuration Register.
00001 IDCoff Current Channel DC Offset Register.
00010 Ign Current Channel Gain Register.
00011 VDCoff Voltage Channel DC Offset Register.
00100 Vgn Voltage Channel Gain Register.
00101 Cyc le Count Number of A/D cycles per computation cycle.
00110 Pulse-Rate Used to set the energy-to-pulse ratio on EOUT (and EDIR).
00111 I Instantaneous Current Register (most recent current sample).
01000 V Instantaneous Voltage Register (most recent voltage sample).
01001 P Instantaneous Power Register (most recent power sample).
01010 E Energy Register (accumulated over latest computation cycle).
01011 IRMS RMS Curr ent Register (computed over latest computation cycle).
01100 VRMS RMS Voltage Register (computed over latest computation cycle).
01101 TBC Timebase Calibration Register.
01110 Poff Power Offset Register.
01111 Status Status Register.
10000 IACoff Current Channel AC Offset Register.
10001 VACoff Voltage Channel AC Offset Register.
10010 Res Reserved †
. . .
. . .
10111 Res Reserved †
11000 Res Reserved †
11001 Test Reserved †
11010 Mask Mask Register.
11011 Res Reserved †
11100 Ctrl Control Register.
11101 Res Reserved †
. . .
. . .
11111 Res Reserved †
† These registers are for Internal Use only and should not be written to.
B7 B6 B5 B4 B3 B2 B1 B0
0W/R
RA4 RA3 RA2 RA1 RA0 0
CS5460A
42 DS487F5
4.2 Serial Port Interface
The CS5460A’s slave-mode serial interface con-
sists of two control lines and two data lines, which
have the following pin-names: CS, SCLK, SDI,
SDO. Each control line is now described.
CS Chip Select (input pin), is the control line which
enables access to the serial port. When CS is set
to logic 1, the SDI, SDO, and SCLK pins will be
held at high impedance. When the CS pin is set to
logic 0, the SDI, SDO, and SCLK pins have the fol-
lowing functionality:
SDI Serial Data In (input pin), is the user-generat-
ed signal used to transfer (send) data/com-
mand/address/etc. bits into the device.
SDO Serial Data Out (output pin), is the data sig-
nal used to read output data bits from the device’s
registers.
SCLK Serial Clock (input pin), is the serial
bit-clock which controls the transfer rate of data
to/from the ADC’s serial port. To accommodate op-
to-isolators, SCLK is designed with a Schmitt-trig-
ger input to allow an opto-isolator with slower rise
and fall times to directly drive the pin. Additionally,
SDO is capable of sinking or sourcing up to 5 mA
to directly drive an opto-isolator LED. SDO will
have less than a 400 mV loss in the drive voltage
when sinking or sourcing 5 mA.
4.3 Serial Read and Write
The state machine decodes the command wo rd as
it is received. Data is written to and read from the
CS5460A by using the Register Read/Write com-
mand. Figure 1 illustrates the serial sequence nec-
essary to write to or read from the serial port
buffers. As shown in Figure 1, a transfer of data is
always initiated by sending the appropriate 8-bit
command (MSB first) to the serial port (SDI pin). It
is important to note that some commands use in-
formation from the Cycle-Count Register and Con-
figuration Register to perform the function. For
those commands, it is important that the correct in-
formation is written to those registers first.
4.3.1 Register Write
When a command involves a write operation, the
serial port will continue to clock in the data bits
(MSB first) on the SDI pin for t he next 24 SCLK cy-
cles. Command words instructing a register write
must be followed by 24 bits of data. For instance,
to write the Configuration Register, the command
(0x40) is transmitted to initiate a write to the Con-
figuration Register. The CS5460A will acquire the
serial data input from the SDI pin after 24 pulses
on the SCLK pin. Once the data is received, the
state machine writes the data to the Configuration
Register and then waits to receive another valid
command.
4.3.2 Register Read
When a read command is initiated, the serial port
will start transferring register content bits (MSB
first) on the SDO pin for the next 8, 16, or 24 SCLK
cycles. Command words instructin g a register read
may be terminated at 8-bit boundaries (e.g., read
transfer s may be 8, 16, or 24 bits in leng th). Also,
data register reads allow “command chaining”, in
which the micro-controller is allowed to send a new
command while reading register data. The new
command will be acted upon immediately and
could possibly terminate the first register read. For
example, if a command word is sent to the state
machine to read one of the output registers, then
after pulsing SCLK for 16-bits of data, a second
write command word (e.g., to clear the Status Reg-
ister) may be pulsed on to the SDI line at the same
time the last 8-bits of data (from the first read com-
mand) are pulsed from the SDO line.
During the read cycle, the SYNC0 command
(NOP) should be strobed on the SDI port while
clocking the data from the SDO port.
4.4 System Initialization
A software or hardware reset can be initiated at
any time. The software reset is initiated by writing
a logic 1 to the RS (Reset System) bit in the Con-
figuration Register, which automatically returns to
logic 0 after reset. At the end of the 32nd SCLK
(i.e., 8 bit command word and 24 bit da ta wor d) in-
ternal synchronization delays the loading of the
Configuration Register by 3 or 4 DCLK cycles.
Then the reset circuit initiates the reset routine on
the 1st falling edge of MCLK.
A hardware reset is initiated when the RESET pin
is forced low for at least 50 ns. The RESET signal
is asynchronous, requiring no MCLKs for the part
to detect and store a reset event. The RESET pin
is a Schmitt Trigger input, which allows it to accept
CS5460A
DS487F5 43
slow rise times and/or noisy control signals. (It is
not uncommon to experience temporary pe riods of
abnormally high noise and/or slow, gradual resto-
ration of power, during/after a power “black-ou t” or
power “brown-out” event.) Once the RESET pin is
de-asserted, the internal reset circuitry remains ac-
tive for 5 MCLK cycles to insure resetting the syn-
chronous circuitry in the device. The modulators
are held in reset for 12 MCLK cycles after RESET
is de-asserted
. After a hardware or software reset,
the internal registers (som e of which may drive out-
put pins) will be reset to their default values on the
first MCLK received after detecting a reset event
(see Table 3). The CS5460A will then assume its
active state. (The term active state, as well as the
other possible power states of the CS5460A, are
described in Section 4.6).
The reader should refer to Section 5 for a complete
description of the registers listed in Table 3.
4.5 Serial Port Initialization
It is possible for the serial interface to become un-
synchronized with respect to the SCLK input. If
this occurs, any attempt to clock valid CS5460A
commands into the serial interface will result in ei -
ther no operation or unexpected operation be-
cause the CS5460A will not interpret the input
command bits correctly. The CS5460A’s serial port
must then be re-initialized. To initialize the serial
port, any of the following actions can be performed:
1) Power on the CS5460A. (Or if the device is a l-
ready powered on, recycle the power.)
2) Hardware Reset.
3) Issue the Serial Port Initialization Sequence,
which is performed by clocking 3 (or more)
SYNC1 command bytes (0xFF) followed by
one SYNC0 command byte (0xFE) to the serial
interface.
4.6 CS5460A Power States
Active state denotes the operation of CS5460A
when the device is fully powered on (i.e., not in
sleep state or stand-by state). Performing any of
the following actions will insure that the CS5460A
is operating in the active state:
1) Power on the CS5460A. (Or if the device is a l-
ready powered on, recycle the power.)
2) Hardware Reset
3) Software Reset
In addition to the three actions listed above, if the
device is operating in sleep state or stand-by state,
waking up the device out of sleep state or stand-by
state (by issuing the Power-Up/Halt command) will
also insure that the device is set into active state.
But in order to send the Power-Up/Halt command
to the device, the serial port has to be initialized.
Therefore, successful wake-up of the device can
be insured by writing the serial port initialization se-
quence to the serial interface, prior to writing the
Power-Up/Halt command.
For a description of the sleep power state and the
stand-by power state, see the Power Down Com-
mand, located in Section 4.1.
Configuration Register: 0x000001
DC offset registers: 0x000000
Gain registers 0x400000
Pulse-Rate Register: 0x0FA000
Cycle-Counter Register: 0x000FA0
Timebase Register: 0x800000
Status Register: (see Section 5)
Mask Register: 0x000000
Control Register: 0x000000
AC offset registers: 0x000000
Power Offset Register: 0x000000
All data registers: 0x000000
All unsigned data registers 0x000000
Table 3. Default Register Values upon Reset Event
CS5460A
44 DS487F5
5. REGISTER DESCRIPTIONS
Note: 1. ** “default” => bit status after software or hardware reset
2. Note that all registers can be read from, and written to.
5.1 Configuration Register
Address: 0
Default** = 0x000001
K[3:0] Clock divider. A 4 bit binary number used to di vide the valu e o f MCLK to ge ner ate the inter na l
clock DCLK. The internal clock frequency is DCLK = MCLK/K. The value of K can range be-
tween 1 and 16. Note that a value of “0000” will set K to 16 (not zero).
iCPU Inverts the CPUCLK clock. In order to reduce the level of noise present when analog signals
are sampled, the logic dr iven by CPUCLK should not be activ e durin g the sa mple edg e.
0 = normal operatio n (d ef au lt)
1 = minimize noise when CPUCLK is driving rising edge logic
IHPF Control the use of the High Pass Filter on the Current Channel.
0 = High-pass filter is disabled. If VHPF is set, use all-pass filter. Otherwise, no filter is used.
(default)
1 = High-pass filter is enabled.
VHPF Control the use of the High Pass Filter on the voltage Channel.
0 = High-pass filter is disabled. If IHPF is set, use all-pass filter. Otherwise, no filter is used.
(default)
1 = High-pass filter enabled
23 22 21 20 19 18 17 16
PC6 PC5 PC4 PC3 PC2 PC1 PC0 Gi
15 14 13 12 11 10 9 8
EWA Res Res SI1 SI0 EOD DL1 DL0
76543210
RS VHPF IHPF iCPU K3 K2 K1 K0
Current
Channel
Voltage
Channel
Cycle-Counter Registe
Status Register (1 × 24)
Serial Interface
Mask Register (1 × 24)
Unsigned Output Registers (2 × 24)
(I , V )
Command Word
State Machine
Transmit Buffer
Receive Buffer
Signed Output Registers (4 × 24)
(I, V, P, E)
RMS RMS
24-Bit
SDI
CS
SDO
SCLK
INT
AC Offset Register (1 x 24)
AC Offset Register (1 x 24)
Control Register (1 x 24)
Power Offset Register (1 x 24)
Configuration Register (1 × 24)
Pulse-Rate Register (1 × 24)
Offset Register (1 × 24)DC
Offset Register (1 × 24)DC Gain Register (1 × 24)AC/DC
Gain Register (1 × 24)AC/DC
r(1×24)
Timebase Cal. Register (1 x 24)
Figure 21. CS5460A Register Diagram
CS5460A
DS487F5 45
RS Start a chip reset cycle when set 1. The reset cycle lasts for less than 10 XIN cycles. The bit is
automatically returned to 0 by th e reset cycle.
DL0 When EOD = 1, EDIR beco m es a us er def i ned pin . DL0 s et s the valu e of th e EDIR pin.
Default = '0'
DL1 When EOD = 1, EOUT becomes a user defined pin. DL1 sets the value of the EOUT pin.
Default = '0'
EOD Allows the EOUT and EDIR pins to be controlled by the DL0 and DL1 bits. EOUT and EDIR can
also be accessed using the Status Register.
0 = Normal operation of the EOUT and EDIR pins. (default)
1 = DL0 and DL1 bits control the EOUT and EDIR pins.
SI[1:0] Soft interrupt configur ation. Select the desired pin behavior for indication of an interrupt.
00 = active low level (default)
01 = active high level
10 = falling edge (INT is normally high)
11 = rising edge (INT is normally low)
Res Reserved. These bits must be set to zero.
EWA Allows the output pins of EOUT and EDIR of multiple chips to be conn ected in a wire-AND, us-
ing an external pull-up device.
0 = normal outputs (default)
1 = only the pull-down device of the EOUT and EDIR pins are active
Gi Sets the gain of the current PGA
0 = gain is 10 (default)
1 = gain is 50
PC[6:0] Phase compensation. A 2’s com plement n umber used to set the delay in the voltage channel.
When MCLK = 4.096 MHz and K = 1, the phase adjustment range is about -2.8 to +2.8 degrees
and each step is about 0 .04 degrees (this as sume s that the powe r line fre quency is 6 0 Hz). If
(MCLK / K) is not 4.096 MHz, the values for the range and step size should be scaled by the
factor 4.096 M Hz / (MC LK / K).
Default setting is 0000000 = 0.0215 degrees phase delay (when MCLK = 4.096 MHz).
CS5460A
46 DS487F5
5.2 Current Channel DC Offset Register and Voltage Channel DC Offset Register
Address: 1 (Current Channel DC Offset Register)
3 (Voltage Channel DC Offset Register)
Default** = 0.000
The DC offset registers are initialized to zero on reset, allowing the device to function and perform measure-
ments. The register is loaded after one computation cycle with the current or voltage offset when the proper input
is applied and the DC Calibration Command is received. DRDY will be asserted at the end of the calibration.
The register ma y be read a nd stored so the re gister may be resto red with the desired system offset compensa-
tion. The value is in the range ± full scale. The numeric format of this register is two’s complement notation.
5.3 Current Channel Gain Register and Voltage Channel Gain Register
Address: 2 (Current Chan n el Ga in Re gis ter )
4 (Voltage Channel Gain Register)
Default** = 1.000
The gain registers are initialized to 1.0 on reset, allowing the device to function and perform measurements. The
gain registers hold th e result of either the AC or DC gain calibrations, whichever was most recently per formed.
If DC calibration is perform ed, the registe r is loaded a fter one computation cycle with the system ga in when the
proper DC input is applied and the Calibration Command is received. If AC calibration is performed, then after
~(6N + 30) A/D conversion cycles (where N is the value of the Cycle-Count Register) the register(s) is loaded
with the system gain when the proper AC input is applied and the Calibration Command is received. DRDY will
be asserted at the end of the calibration. The register may be read and stored so the register may be restored
with the desired system offset compensation. The value is in the range 0.0 Gain < 4.0.
5.4 Cycle Count Register
Address: 5
Default** = 4000
The Cycle Count Register value (denoted as ‘N’) specifies the number of A/D conversion cycles per computation
cycle. For each computation cycle, the updated results in the RMS and Energy Registers are co mpu ted usin g
the most recent set of N continuous instantaneous voltage/current samples. When the device is command ed to
operate in ’continuous computation cycles’ data acquisition mode, the computation cycle frequency is
(MCLK / K) / (1024 N) where MCLK is master clock input frequency (into XIN / XOUT pins), K is the clock di-
vider value (as specified in the Configuration Register), and N is Cycle Count Register value.
MSB LSB
-(20)2
-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23
MSB LSB
21202-1 2-2 2-3 2-4 2-5 2-6 ..... 2-16 2-17 2-18 2-19 2-20 2-21 2-22
MSB LSB
223 222 221 220 219 218 217 216 ..... 26252423222120
CS5460A
DS487F5 47
5.5 Pulse-Rate Register
Address: 6
Default** = 32000 .00Hz
The Pulse-Rate Register determines the freq uen cy of th e trai n of pul ses ou tput on the EOUT pin. Each EOUT
pulse represents a predetermined magnitude of real (billable) energy. The register’s smallest valid value is 2-4
but can be in 2-5 increments.
5.6 I,V,P,E Signed Output Register Results
Address: 7 - 10
These signed registers contain the last value of the measured results of I, V, P, and E. The results are in the
range of -1.0 I, V, P, E 1.0. The value is represented in two's complement notation, with the binary point
place to the right of the MSB (which is the sign bi t). I, V, P, and E are output results registers which contain
signed values. Note that the I, V, and P Registers are u pdated every conversion cycle, while the E Register is
only updated after each computation cycle. The numeric format of this register is two’s complement notation.
5.7 IRMS, VRMS Unsigned Output Register Results
Address: 11,12
These unsign ed regi st er s con ta in th e last valu e of th e ca lc ula te d resu lts of IRMS and VRMS. The results are in
the range of 0.0 IRMS,VRMS 1.0. The value is represented in binary notation, with the binary point place to
the left of the MSB. IRMS and V RMS are output result registers which contain unsigned values.
5.8 Timebase Calibration Register
Address: 13
Default** = 1.000
The Timebase Calibration Register is initialized to 1.0 on reset, allowing the device to function and perfor m com-
putations. The register can be loaded with the clock frequency error to compensate for a gain error caused by
the crystal/oscillator tolerance. The value is in the range 0.0 TBC 2.0.
MSB LSB
218 217 216 215 214 213 212 211 ..... 21202-1 2-2 2-3 2-4 2-5
MSB LSB
-(20)2
-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23
MSB LSB
2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 ..... 2-18 2-19 2-20 2-21 2-22 2-23 2-24
MSB LSB
202-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23
CS5460A
48 DS487F5
5.9 Power Offset Register
Address: 14
Default** = 0.000
This offset value is added to each power value that is computed for each voltage/current sample pair before
being accumulated in the Energy Register. The numeric format of this register is two’s complement notation.
This register can be used to offset contributions to the energy result that are caused by undesirable sources of
energy that are inherent in the system.
5.10 Current Channel AC Offset Register and Voltage Channel AC Offset Register
Address: 16 (Current Channel AC Offset Register)
17 (Voltage Channel AC Offset Register)
Default** = 0.000
The AC offset registers are initialized to zero on reset, allowing the device to function and perform measure-
ments. First, the grou nd-level inpu t sh oul d be applie d to the inputs. Then the AC Offset Calibration Command
is should be sent to the CS5460A. After ~(6N + 30) A/D conversion cycles (where N is the value of the Cy-
cle-Count Register), the gain register(s) is loaded with the square of the system AC offset value. DRDY will be
asserted at the end of th e calibration. The register ma y be read and stored so the register may be restore d with
the desired system offset compensation. Note that this register value represents the square of the AC cur-
rent/voltage offset.
5.11 Status Register and Mask Register
Address: 15 (Status Register)
26 (Mask Register)
Default** = Binary: 00000000000000xxxx000001 (St atus Regis ter) {x = state depends on device revision}
Binary: 000000000000000000000000 (Mask Register)
The Status Register indicates the condition of the chip. In normal operation writing a '1' to a bit will cause the bit
to go to the '0' state. Writing a '0' to a bit will maintain the status bit in its current state. With this feature the user
can write logic ‘1’ values back to the Status Register to selectively clear only those bits that have been re-
solved/registered by the system MCU, without concern of clearing any newly set bits. Even if a status bit is
masked to prevent the interrupt, the corresponding status bit will still be set in the Status Register so the user
can poll the status.
The Mask Register is used to control the activation of the INT pin. Placing a logic '1' in the Mask Register will
MSB LSB
-(20)2
-1 2-2 2-3 2-4 2-5 2-6 2-7 ..... 2-17 2-18 2-19 2-20 2-21 2-22 2-23
MSB LSB
2-13 2-14 2-15 2-16 2-17 2-18 2-19 2-20 ..... 2-30 2-31 2-32 2-33 2-34 2-35 2-36
23 22 21 20 19 18 17 16
DRDY EOUT EDIR CRDY MATH Res IOR VOR
15 14 13 12 11 10 9 8
PWOR IROR VROR EOR EOOR Res ID3 ID2
76543210
ID1 ID0 WDT VOD IOD LSD 0 IC
CS5460A
DS487F5 49
allow the corresponding bit in the Status Register to activate the INT pin when the status bit becomes active.
IC Invalid Command. Normally logic 1. Set to logic 0 when the part is given an invalid command .
Can be deactivated only by sending a port initialization sequence to the serial port (or by exe-
cuting a software/hardware reset). When writing to the Status Register, this bit is ignored.
LSD L ow Supply Detect. Set when the voltage at th e PFMON pin falls below the low-voltage thresh-
old (PMLO), with respect to VA- pin. For a given part, PMLO can be as low as 2.3 V. LSD bit
cannot be permanently rese t until the voltage at PFMON pin rises back ab ove the high-vol tage
threshold (PMHI), which is typically 100mV above the device’s low-voltage threshold. PMHI will
never be greater than 2.7 V.
IOD Modulator oscillation detect on the current channel. Set when the modulator oscillates due to
an input above Full Scale. Note that the level at which the modulator oscillates is significantly
higher than the current channel’s Differential Input Voltage Range.
VOD Modulator oscillation detect on the voltage channel. Set when the modulator oscillates due to
an input above Full Scale. Note that the level at which the modulator oscillates is significantly
higher than the current channel’s Differential Input Voltage Range.
Note: The IOD and VOD bits may be ‘falsely’ triggered by very brief voltage spikes from the
power line. This event sh ou ld no t be con fu se d with a DC over loa d situatio n at th e
inputs, when the IOD and VOD bits will re-assert themselves even after being
cleared, multiple times.
WDT Watch-Dog Timer. Set when there has been no reading of the Energy Register for more than
5 seconds. (MCLK = 4.096 MHz, K = 1) To clear this bit, first read the Energy Register, then
write to the Status Register with this bit set to logic '1'. When MCLK/K is not 4.096 MHz, the
time duration is 5 * [4.096 MHz / (MCLK/K)] seconds.
ID3:0 Revision/Version Identification.
EOOR The internal EOUT Energy Accumulation Register went out of range. Note that the EOUT En-
ergy Accumulation Register is different than the Energy Register available through the serial
port. This register cannot be read by the user. Assertion of this bit can be caused by having
an output rate that is too small for the power being measured. The problem can be corrected
by specifying a higher frequency in the Pulse-Rate Regi ster.
EOR Ene rgy Out of Range. Set when the Energy Register overflows, be cause the amount of energy
that has been accumulated during the pending computation cycle is greater than the r egister’s
highest allowable positive value or below the register’s lowest allowable nega tive value.
VROR RMS Voltage Out of Range. Set when the calibrated RMS voltage value is too large to fit in the
RMS Voltage Register.
IROR RMS Current Out of Range. Set when the calibr ated RMS current value is too large to fit in the
RMS Current Register.
PWOR Power Calculation Out of Range. Set when the magnitude of the calculated power is too large
to fit in the Instantaneous Power Register.
VOR Voltage Out of Range.
IOR Current Out of Range. Set when the magnitude of the calibrated current value is too large or
too small to fit in the Instantaneous Current Register.
MATH General computation Indicates that a divide operation overflowed. This can happen normally
in the course of computation. If this bit is asserted but no other bits are asserted, then there is
no error, and this bit should be ignored.
CS5460A
50 DS487F5
CRDY Conversion Ready. Indicates a new conversion is ready. This will occur at the output word rate,
which is usually 4 kHz.
EDIR Set whenever the EOUT bit asserted (see below) if the accumulated energy is negative.
EOUT Indicates that enough positive/negative ener gy has been reached within the inter nal EOUT En-
ergy Accumulation Register (not accessib le to user) to mandate the ge neration of one or more
pulses on the EOUT pin (if enabled, see Configuration Register ). The energy flow may indicate
negative energy or positive energy. (The sign is determined by the EDIR bit, described above).
This EOUT bit is cleared automatically when the ene rgy rate drops belo w the level that produc-
es a 4 kHz EOUT pin rate. The bit can also be cleared by writing to the Status Register. This
status bit is set with a maximum frequency of 4 kHz (when MCLK/K is 4.096 MHz). When
MCLK/K is not equal to 4. 09 6 M Hz, the us er should scale the pulse-rate by a factor of
4.096 MHz / (MCLK/K) to get the actual pulse-rate.
DRDY Data Ready. When running in ’single computation cycle’ or ’continuous computation cycles’
data acquisition modes, this bit will indicate the end of computation cycles. When running cali-
brations, this bit indicates that the calibration sequence has completed, and the results have
been stored in the offset or gain registers.
5.12 Control Register
Address: 28
Default** = 0x000000
STOP 1 = used to terminate the new EEBOOT sequence.
Res Reserved. These bits must be set to zero.
MECH 1 = widens EOUT and EDIR pulses for mechanical counter s.
INTL 1 = converts the INT output to open drain configuration.
SYNC 1 = forces internal A/D converter clock to synchronize to the initiation of a conversion command.
NOCPU 1 = converts the CPUCLK output to a one-bit output port. Reduces power consumption.
NOOSC 1 = saves power by disabling the crystal oscillator for external drive.
STEP 1 = enables stepper-motor signals on the EOUT/EDIR pins.
23 22 21 20 19 18 17 16
ResResResResResResResRes
15 14 13 12 11 10 9 8
Res Res Res Res Res Res Res STOP
76543210
Res MECH Res INTL SYNC NOCPU NOOSC STEP
CS5460A
DS487F5 51
6. PIN DESCRIPTIONS
1
2
3
4
5
6
7
817
18
19
20
21
22
23
24
9
10
11
12 13
14
15
16
Crystal Out XOUT
CPU Clock Output CPUCLK
Positive Digital Supply VD+
Digital Ground DGND
Serial Clock Input SCLK
Serial Data Output SDO
Chip Select CS
Mode Select MODE
Differential Voltage Input VIN+
Differential Voltage Input VIN-
Voltage Reference Output VREFOUT
Voltage Reference Input VREFIN
XIN Crystal In
SDI Serial Data Input
EDIR Energy Direction Indicato r
EOUT Energy Output
INT Interrupt
RESET Reset
NC No Connect
PFMON Power Fail Monitor
IIN+ Differential Current Input
IIN- Differential Current Input
VA+ Positive Analog Supply
VA- Analog Ground
Clock Generator
Crystal Out
Crystal In 1,24 XOUT, XIN - A gate inside the chip is connected to these pins and can be used with a
crystal to provide the system clock for the device. Alte rn at ive ly, an external (CMOS
compatible clock) can be supplied into XIN pin to provide the system clock for the device.
CPU Clock Output 2CPUCLK - Output of on-chip oscillator which can drive one standard CMOS load.
Control Pins and Serial Data I/O
Serial Clock Input 5SCLK - A clock signal on this pin determines the input and output rate of the data for the
SDI and SDO pins respectively. This input is a Schmitt trigger to allow for slow rise time
signals. The SCLK pin will recognize clocks only when CS is low.
Serial Data Output 6SDO - SDO is the output pin of the serial data port. Its output will be in a high impedance
state when CS is high.
Chip Select 7CS - When low, the port will recognize SCLK. An active high on this pin forces the SDO
pin to a high impedance state. CS should be changed when SCLK is low.
Mode Select 8MODE - When at logic high, the CS5460A can perform the auto-boot sequence with the
aid of an external serial EEPROM to receive commands and settings. When at logic low,
the CS5460A assumes normal “host mode” operation . This pi n is pulled down to logic
low if left unconnected, by an internal pull-down resistor to DGND.
Interrupt 20 INT - When INT goes lo w it sign als that an enabled event has occurred. INT is cleared
(logic 1) by writing the appropriate command to the CS546 0A.
Energy Output 21 EOUT - The energy output pin output a fixed-width pulse rate output with a rate (pro-
grammable) proportional to real (billa ble) energy.
Energy Direction
Indicator 22 EDIR - The energy direction indicator indicates if the measured energy is negative.
Serial Data Input 23 SDI - the input pin of the serial data port. Data will be input at a rate determined by SCLK.
Measurem e nt an d Refe re nc e In pu t
Differential
Voltage Inputs 9,10 VIN+, VIN- - Differential analog input pins for voltage channel.
CS5460A
52 DS487F5
Voltage
Reference Output 11 VREFOUT - The on-chip voltage reference is output from this pin. The voltage reference
has a nominal magnitude of 2.5 V and is reference to the VA- pin on the converter.
Voltage
Reference Input 12 VREFIN - The voltage input to this pin establishes the voltage reference for the on-chip
modulator.
Differential
Current Inputs 15,16 IIN+, IIN- - Differential analog input pins for current channel.
Power Supply Connections
Positive
Digital Supply 3VD+ - The positive digital supply is nominally +5 V ±10% rel ative to DGND.
Digital Ground 4DGND - The common-mode potential of digital ground must be equal to or above the
common-mode potential of VA-.
Negative
Analog Supply 13 VA- - The negative analog supply pin must be at the lowest potential.
Positive
Analog Supply 14 VA+ - The positive analog supply is nominally +5 V ±10% re lative to VA-.
Power Fail Monitor 17 PFMON - The power fail Monitor pin monitors the analog supply. Typical threshold le vel
(PMLO) is 2.45 V with respect to the VA- pin. If PFMON voltage threshold is tripped, the
LSD (low-supply detect) bit is set in the St atus Register. Once the LSD bit has been set,
it will not be able to be reset until the PFMON voltage increases ~100 mV (typical) above
the PMLO voltage. Therefore, there is hysteresis in the PFMON function.
RESET 19 Reset - When reset is taken low, all internal registers are set to th eir default states.
Other
No Connection 18 NC - No connection. Pin should be left floating.
CS5460A
DS487F5 53
7. PACKAGE DIMENSIONS
Notes: 1. “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include mold
mismatch and are measured at the parting li ne, mold flash or protrusions shall not exceed 0.20 mm per
side.
2. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be
0.13 mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall not
reduce dimension “b” by more than 0.07 mm at least material condition .
3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.
INCHES MILLIMETERS NOTE
DIM MIN NOM MAX MIN NOM MAX
A -- -- 0.084 -- -- 2.13
A1 0.002 0.006 0.010 0.05 0.13 0.25
A2 0.064 0.068 0.074 1.62 1.73 1.88
b 0.009 -- 0.015 0.22 -- 0.38 2,3
D 0.311 0.323 0.335 7.90 8.20 8.50 1
E 0.291 0.307 0.323 7.40 7.80 8.20
E1 0.197 0.209 0.220 5.00 5.30 5.60 1
e 0.022 0.026 0.030 0.55 0.65 0.75
L 0.025 0.03 0.041 0.63 0.75 1.03
0° 4° 8° 0° 4° 8°
JEDEC #: MO-150
Controlling Dimension is Millimeters.
24L SSOP PACKAGE DRAWING
E
N
123
eb2A1
A2 A
D
SEATING
PLANE
E11
L
SIDE VIEW
END VIEW
TOP VIEW
CS5460A
54 DS487F5
8. ORDERING INFORMATION
9. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION
* MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020.
10. REVISION HISTORY
Model Temperature Package
CS5460A-BSZ (lead free) -40 to +85 °C 24-pin SSOP
Model Number Peak Reflow Temp MSL Rating* Max Floo r Life
CS5460A-BSZ (lead free) 260 °C 3 7 Days
Revision Date Changes
F2 September 2004 Added Lead Free part numbers
F3 August 2005 Updated legal notice.
F4 November 2007 Changed PSSR for voltage channel fro m 48 dB min. to 65 dB typical.
F5 April 2011 Removed lead-containing (Pb) device ordering information.
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find the one nearest to you go to www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. Howe ver, the informatio n is sub ject
to change wi thout noti ce and is pro vided "AS IS" without war ranty of any kind (exp ress or impli ed). Cust omers are adv ised to obtain t he latest version of relevant
information to ver ify, before placin g orders, that inform ation bei ng relied on is curr ent and co mplete. All produ cts are sold subject to the terms and conditions of sale
supplied a t the time of order acknowledgmen t, including those pe rtaining to warranty, in demnification, an d limitation of liabi lity. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, m ask wo rk rights,
copyrights, trademar ks, trade secrets or other intellectual prope rty rights. Cirrus owns the copyrights associated with the in formation contained herein and gives con-
sent for copies to be ma de of the information only for use with in your organization with re spect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROP-
ERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMO TIVE SAFETY, SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITI-
CAL. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDER STOOD TO BE FULLY AT THE CUSTOMER 'S RISK AND CIRRUS DIS CLAIMS
AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUS-
TOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY
CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS'
FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
SPI is a registered trademark of Motorola, Inc.
Microwire is a tra de mark of National Semico nd uctor Cor po ra tion .
