A Electrical Capacity (Resistive Load) Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On & On-None-Off; 3A @ 30V DC for all other circuits Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Logic/Power Level (gold over silver): Combines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold Insulation Resistance: 1,000 megohms minimum @ 500V DC Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts and case for 1 minute minimum Mechanical Life: 100,000 operations minimum; 50,000 operations minimum for flat, locking & splashproof devices Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold; 50,000 operations minimum for silver at 3A @ 125V AC Angle of Throw: 25 Materials & Finishes Toggle: Bushing: Case: Movable Contactor: Movable Contacts: Stationary Contacts: Rotaries Operating Temp Range: -30C through +85C (-22F through +185F) Humidity: 90 ~ 95% humidity for 96 hours @ 40C (104F) Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Sealing: Splashproof bushing options B3, D3, D8, L3, & L8, which have o-rings inside & outside the bushing, meet IP67 of IEC60529 Standards. Tactiles Slides Brass with chrome plating Frame: Stainless steel Brass with nickel plating Support Bracket: Brass with tin plating Diallyl phthalate resin (UL94V-0) Phosphor bronze with silver or gold plating Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Silver with silver plating (code W); copper or brass with gold plating (code G); or silver with gold plating (code A) Terminals: Copper or brass with silver plating; or copper or brass with gold plating Environmental Data Tilt Installation Touch Processing Mounting Torque: 3.0Nm (26.55 lb*in) double nut for large bushing; 1.5Nm (13 lb*in) double nut & 0.7Nm (6 lb*in) single nut for all other bushings Soldering: Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Lever must be in OFF (center) position while soldering. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & Certifications Flammability Standards: UL94V-0 for case UL: File No. E44145 - Recognized only when ordered with marking on switch. Add "/U" or "/CUL" before dash in part number to order UL recognized switch. All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. Add "/C" before dash in part number to order CSA certified switch. All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. Supplement Accessories Indicators Miniature Toggles General Specifications Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M A52 www.nkkswitches.com 5/9/18 Distinctive Characteristics Rockers A Toggles Series M Miniature Toggles Pushbuttons Antirotation design, standard on noncylindrical levers, mates toggle and bushing; bottom of toggle has two flatted sides which fit into a complementary opening inside bushing. Programmable Illuminated PB Antijamming design protects contacts from damage due to excessive downward force on actuator. High torque bushing construction prevents rotation or separation from frame during installation. High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. Keylocks Molded diallyl phthalate case has a UL flammability rating of 94V-0. Rotaries Epoxy sealed terminals prevent entry of solder flux and other contaminants. Slides Prominent external insulating barriers increase insulation resistance and dielectric strength. Tactiles Interlocked actuator block, lever, and interior guide prevent switch failure due to biased lever movement. Actual Size Page A52 Bracket PC Mount Page A64 Angle PC Mount Page A70 www.nkkswitches.com A53 Supplement Accessories Indicators Bushing Mount Touch Tilt Clinching of frame to case well above base and terminals provides 1,500V dielectric strength. TYPICAL SWITCH M20 1 S .413" (10.5mm) Bat S2 .200" (5.08mm) Bat S3 .256" (6.5mm) Bat E .450" (11.4mm) Flatted 3PDT * E2 .256" (6.5mm) Flatted 4PDT DP3T E4 1 SPST SPDT 2 DPST DPDT SP3T 3 4 S S1 Small Toggles Rotaries Slides Tactiles Tilt Touch 3 Poles Keylocks Programmable Illuminated PB Bushing Mount Miniature Toggles A Pushbuttons Rockers Toggles Series M .840" (21.3mm) Flatted *Q .550" (14.0mm) Cone * Q2 .640" (16.26mm) Cone * Q4 .840" (21.3mm) Cone *C .571" (14.5mm) Color Tipped Cone (available in colors A, B & C only) D .840" (21.3mm) Color Capped Cone Specify cap color for toggles C & D at the end of the part number. * Available on 1- and 2-pole only. Circuits *1 ON NONE OFF 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) B .453" (11.5mm) Large Bat 8 (ON) OFF (ON) B2 .689" (17.5mm) Large Bat 9 ON OFF (ON) R .610" (15.5mm) Large Flatted ** 4 ON ON ON ** 6 (ON) ON (ON) ** 7 ON ON (ON) ( ) = Momentary * ON-NONE-OFF circuit avail- Small Bushings S1 .350" (8.9mm) Threaded with Keyway S4 6mm .350" (8.9mm) Threaded with Keyway S2 .350" (8.9mm) Smooth with Keyway A1 .280" (7.1mm) Threaded with Keyway A2 .280" (7.1mm) Smooth with Keyway D1 .350" (8.9mm) Threaded with D Flat D4 6mm .350" (8.9mm) Threaded with D Flat D3 .350" (8.9mm) Threaded Splashproof with D Flat (combines only with S, S2 & S3) D8 6mm .350" (8.9mm) Threaded Splashproof with D Flat (combines only with S, S2 & S3) Large Toggles Large Bushings B1 Large .472" (12mm) Threaded with Keyway B3 Large .472" (12mm) Threaded Splashproof with D Flat Locking Lever L .201" (5.1mm) Dia. Locking Lever Bushings For Locking Levers L1 .291" (7.4mm) Threaded with Keyway for Lever Lock L4 6mm .291" (7.4mm) Threaded with Keyway for Lever Lock L2 Smooth with Keyway for Lever Lock L3 .295" (7.5mm) Threaded Splashproof with D Flat for Lever Lock L8 6mm .295" (7.5mm) Threaded Splashproof with D Flat for Lever Lock able in 1- and 2-pole only. Accessories Indicators ** 3-ON circuits IMPORTANT: Supplement Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. A54 www.nkkswitches.com A ORDERING EXAMPLE Optional Caps For Small Bat Toggles W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max C Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max R V A B Cap Colors A Black For S Bat Toggle B White Conical Cap for S Bat Toggle C Red E Yellow For B Toggle F Green For B2 Toggle G Blue For Large Bat Toggles Programmable Illuminated PB Contact Materials & Ratings Pushbuttons Rockers 01 Keylocks W Cap for Locking Lever Quick Connect 03 .250" (6.35mm) Straight PC 05 .425" (10.8mm) Wirewrap 06 .750" (19.05mm) Wirewrap 07 .964" (24.5mm) Wirewrap 08 1.062" (27.0mm) Wirewrap Black C Red G Blue Slides 02 A Tactiles Solder Lug Tilt 01 Nickel Plated Supplied with Switch Rotaries No Code Terminals Toggles Series M Bushing Mount Miniature Toggles Touch DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2013SS1W01 .413" (10.5mm) Bat Toggle SPDT ON-OFF-ON Circuit Solder Lug Terminals www.nkkswitches.com Supplement Silver Contacts with 6-Amp Rating Accessories 1/4-40 .350" (8.9mm) Threaded Bushing with Keyway A55 Toggles Series M A POLES & CIRCUITS Rotaries Toggle Position ) = Momentary Down Center Connected Terminals Up Down Throw & Schematics Center Up Note: Pole Model SP M2011 ON NONE OFF 2-3 OPEN OPEN SPST SP M2012 M2013 M2015 M2018 M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 OPEN 2-1 SPDT DP M2021 ON NONE OFF 2-3 5-6 OPEN OPEN DPST DP M2022 M2023 M2025 M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 OPEN 2-1 5-4 DPDT 3P M2032 M2033 M2035 M2038 M2039 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 OPEN 2-1 5-4 8-7 3PDT 4P M2042 M2043 M2045 M2048 M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 11-12 OPEN 2-1 5-4 8-7 11-10 4PDT Keyway Keyway Terminal numbers are not actually on the switch. 2 (COM) 3 2 (COM) 3 1 2 Keylocks Programmable Illuminated PB Pushbuttons Rockers ( Slides Bushing Mount Miniature Toggles (COM) 3 6 2 (COM) 3 6 5 3 1 2 5 1 5 1 2 3 5 4 (COM) 6 4 (COM) 9 4 6 8 9 7 8 11 7 12 10 Tactiles For 3 Throw (3-On) Connected Terminals & Schematic Tilt Pole Model SP M2024 M2026 M2027 Down Center ON (ON) ON ON ON ON Up ON (ON) (ON) Center External Connection 2 (in) 5 External Connection 2 (in) 5 3 4 (out) 6 (out) 1 (out) 1 (out) 2-3 5-6 Touch Indicators Accessories Supplement Down DP M2044 M2046 M2047 ON (ON) ON ON ON ON ON (ON) (ON) External Connection 2 (in) 5 External connection must be made during field installation. A56 3 5 2 4 1 (out) Common (in) (out) 2-1 5-4 External Connection 8 (in) 11 2-3 5-4 8-9 11-10 External connection must be made during field installation. www.nkkswitches.com External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) The DP3T model utilizes a four pole base. (out) 6 3 4 (out) 6 (out) 1 (out) 3 4 (out) 6 (out) External Connection 2 (in) 5 External Connection 8 (in) 11 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 1 (out) External Conn External Connection 2 (in) 5 2-3 5-4 2-3 5-6 8-9 11-12 The SP3T model utilizes a double pole base. Up 2-1 5-4 8-7 11-10 (out) External Conn Common (in) (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) A SMALL TOGGLES .256" (6.5mm) Bat S3 Rockers Important: .200" (5.08mm) Bat S2 25 (2.8) Dia .110 (10.5) .413 25 25 (2.7) Dia .106 (2.7) Dia .106 Pushbuttons Toggle length changes based on bushing selected. All illustrations are shown with .350" long bushing. When using a .280" long bushing, toggle length increases .070". (6.5) .256 (5.08) .200 Standard Material & Finish: Brass with Bright Chrome Contact factory for optional finishes. .450" (11.4mm) Flatted .256" (6.5mm) Flatted E2 (5.0) .197 (5.08) .200 .571" (14.5mm) Color Tipped Cone Supplied with Cap AT445 .840" (21.3mm) Flatted E4 C Colors: A B C Material: Polycarbonate 25 (2.5) .098 25 (3.0) Dia .118 25 (2.54) .100 (4.2) .165 (2.5) .098 (11.4) .450 25 (21.3) .840 Rotaries E Programmable Illuminated PB .413" (10.5mm) Bat Keylocks S Toggles Series M Bushing Mount Miniature Toggles (4.5) (14.5) .177 .571 Slides (6.5) .256 .640" (16.26mm) Cone Q2 .840" (21.3mm) Color Capped Cone Supplied with Cap AT460 .840" (21.3mm) Cone Q4 D Tilt .550" (14.0mm) Cone Colors: A B C E F G Material: Polyethylene Only Available in 1- & 2-Pole Cap Colors Available: A Black B White (21.3) .840 (21.3) .840 (16.26) .640 (14.0) .550 C Only Available in 1- & 2-Pole Red E Yellow www.nkkswitches.com Touch (16.4) .646 Indicators 25 (3.1) Dia .122 25 (3.1) Dia .122 Only Available in 1- & 2-Pole F Green G Supplement (3.1) Dia .122 25 25 (3.1) Dia .122 Accessories Q Only Available in 1- & 2-Pole Tactiles Only Available in 1- & 2-Pole Blue A57 SMALL BUSHINGS Pushbuttons 1/4-40 .350" (8.9mm) Threaded with Keyway S1 (0.8) .031 S4 6mm/.350" (8.9mm) Threaded with Keyway (0.8) .031 1/4-40 Thd (0.9) .035 (8.9) .350 (8.0) Dia .315 (0.9) .035 (8.9) .350 (0.8) .031 (0.8) .031 1/4-40 Thd Rotaries 1/4-40 .350" (8.9mm) Threaded with D Flat (0.9) .035 (7.1) .280 (8.0) Dia .315 When using this bushing, toggle length is increased by .070". Maximum Panel Thickness with Standard Hardware: .031" (0.8mm) D1 (6.2) Dia .244 (2.5) .098 (0.9) .035 (7.1) .280 (8.0) Dia .315 (0.9) .035 (8.9) .350 (8.0) Dia .315 .280" (7.1mm) Smooth with Keyway A2 (2.5) .098 (6.2) Dia .244 Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) 1/4-40 .280" (7.1mm) Threaded with Keyway A1 (0.8) .031 (2.5) .098 (8.0) Dia .315 Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) .350" (8.9mm) Smooth with Keyway S2 M6 P0.75 (2.5) .098 (2.5) .098 Keylocks Programmable Illuminated PB Bushing Mount Miniature Toggles A Rockers Toggles Series M D4 When using this bushing, toggle length is increased by .070". 6mm/.350" (8.9mm) Threaded with D Flat 1/4-40 Thd D3 1/4-40 .350" (8.9mm) Threaded Splashproof with D Flat 1/4-40 Thd Slides M6 P0.75 (2.5) .098 (8.0) Dia .315 Tactiles (2.5) .098 (0.9) .035 (8.9) .350 (8.0) Dia .315 Tilt Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) D8 Touch Indicators Accessories Supplement Hardware and Quantity (1.5) .059 (8.9) .350 D8 combines only with S, S2 & S3 toggles. Maximum Panel Thickness with Standard Hardware: .193" (4.9mm) For S1, S2, A1, A2 or S4 Bushing with Keyway & for L1 or L4 Bushing A58 (5.6) or .228 (6.5) Dia .256 (0.6) .024 D3 combines only with S, S2 & S3 toggles. Maximum Panel Thickness with Standard Hardware: .193" (4.9mm) Standard Hardware Supplied for Small Bushings M6 P0.75 (10.0) Dia .394 (1.5) .059 (8.9) .350 (10.0) Dia .394 Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) 6mm/.350" (8.9mm) Threaded Splashproof with D Flat (2.5) .098 (2.5) .098 (0.9) .035 (8.9) .350 Bushing Codes S1/S4 A1 D1/D4 D3/D8 L1/L4 L3/L8 Hex Nut 2 2 2 1 2 1 Locking Ring 1 1 0 0 1 0 Lockwasher 1 1 1 0 1 0 O-ring 0 0 0 1 0 1 For S1, A1 or S4 Bushing with Locking Ring & for L1 or L4 Bushing www.nkkswitches.com (6.5) Dia .256 (2.2) Dia .087 (6.5) or .240 For D1, D4, D3 or D8 Bushing with D Flat & for L3 or L8 Bushing (6.5) Dia .256 (5.8) .228 A LARGE TOGGLES Toggles Series M Bushing Mount Miniature Toggles 25 (6.15) .242 (6.0) Dia .236 (6.0) Dia .236 (17.5) .689 (11.5) .453 25 (3.6) .140 (15.5) .610 Keylocks 25 .610" (15.5mm) Large Flatted Pushbuttons R Programmable Illuminated PB .689" (17.5mm) Large Bat Standard Material & Finish: Brass with Bright Chrome Optional Finishes: Contact factory for satin chrome or black. Large .472" (12.0mm) Threaded Splashproof with D Flat (12.0) .472 (4.9) .193 Tactiles M12 P1 (1.1) .043 (10.9) .429 M12 P1 (18.0) Dia .709 Maximum Panel Thickness with Standard Hardware: .216" (5.5mm) (2.0) .079 Tilt (12.0) .472 Maximum Panel Thickness with Standard Hardware: .256" (6.5mm) Standard Hardware for B1: 1 hex face nut AT503M, 1 locking ring AT506M, 1 lockwasher AT508, and 1 hex backup nut AT527M Touch (1.85) .073 B3 Slides Large .472" (12.0mm) Threaded with Keyway Standard Hardware for B3: 1 hex face nut AT503M and 1 o-ring AT401P Indicators B1 Rotaries LARGE BUSHINGS Panel Cutouts (12.5) Dia .492 For B1 Bushing with Keyway (11.5) .453 (1.5) .060 (12.5) Dia .492 For B1 Bushing with Locking Ring (9.0) .354 (3.0) Dia .118 www.nkkswitches.com For B3 Bushing with D Flat (11.1) .437 (12.5) Dia .492 A59 Accessories B2 Supplement .453" (11.5mm) Large Bat B Rockers Toggle & Bushing Combinations: These toggles combine with the 12mm bushings B1 & B3. Bushing Mount Miniature Toggles A LOCKING LEVER & BUSHINGS LL1 1/4-40 .291" (7.4mm) Threaded with Keyway 6mm/.291" (7.4mm) Threaded with Keyway LL4 (0.8) .031 (8.0) Dia .315 Pushbuttons Rockers Toggles Series M Programmable Illuminated PB (2.5) .098 25 (5.1) Dia .201 1/4-40 Thd 25 (5.1) Dia .201 (16.5) (8.0) .650 .315 (15.0) .591 (4.6) Dia .181 (9.7) .382 (7.4) .291 (0.8) .031 (8.0) Dia .315 (2.5) .098 25 (16.5) (8.0) .650 .315 (15.0) .591 Smooth with Keyway (0.8) .031 (8.0) Dia .315 (2.5) .098 (5.1) Dia .201 LL2 (16.5) .650 (4.6) Dia .181 M6 P0.75 (9.7) .382 (7.4) .291 (8.0) .315 (15.0) .591 (4.6) Dia .181 (6.2) Dia .244 (9.3) (7.0) .366 .275 (0.9) .035 (0.9) .035 (0.9) .035 Keylocks Maximum Panel Thickness with Standard Hardware: .047" (1.2mm) Standard Hardware for L1 & L4: 2 hex nuts AT513H or AT513M, 1 locking ring AT507H or AT507M, and 1 lockwasher AT509 Rotaries LL3 1/4-40 .295" (7.5mm) Threaded Splashproof with D Flat LL8 6mm/.295" (7.5mm) Threaded Splashproof with D Flat (10.0) Dia .394 (10.0) Dia .394 (2.5) .098 Slides (2.5) .098 (5.1) Dia .201 Tactiles (16.5) .650 25 (8.0) .315 (15.0) .591 25 (5.1) Dia .201 (16.5) .650 (4.6) Dia .181 1/4-40 Thd (9.8) .386 (7.5) .295 (8.0) .315 (15.0) .591 (4.6) Dia .181 M6 P0.75 (9.8) .386 (7.5) .295 Tilt (1.5) .059 Maximum Panel Thickness with Standard Hardware: .047" (1.2mm) Standard Hardware for L3 and L8: 1 hex nut AT513H or AT513M and 1 o-ring AT516 Indicators Touch Lever Material & Finish: Brass with Chrome Plating on-none-on on-none-(on) on-off-(on) on-on-(on) on-off-on on-on-on (on)-off-(on) (on)-on-(on) 2 positions lock 1 position locks 2 positions lock 3 positions lock 1 position locks Locking Mechanism No Code Supplement Accessories (1.5) .059 Supplied with Cap AT427 Lever Cap Material: Brass with Nickel Plating A60 Color Codes for Optional Anodized Aluminum Caps A www.nkkswitches.com Black C Red G Blue A Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: See Supplement section to find complete explanation of operating range. Power Level or Logic Level 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. TERMINALS .062" (1.57mm) Wide Quick Connect 02 (4.0) .157 Epoxy Seal (6.35) .250 Epoxy Seal (2.0) .079 (2.0) (1.1) .079 .043 Thk = (0.8) .031 .250" (6.35mm) Straight PC (4.8) .189 3 2 (6.35) (4.8) .250 .189 Epoxy Seal Thk = (0.8) .031 (4.7) Typ .185 1 (1.8) Dia Typ .073 (1.17) .046 Thk = (0.8) .031 .425" (10.8mm) Wirewrap or Extended PC 06 .750" (19.05mm) Wirewrap or Extended PC 6 2 5 1 4 (4.7) Typ .185 3 6 9 2 5 8 1 4 (4.8) Typ .189 (4.7) Typ .185 7 3 6 9 12 2 5 8 11 1 4 7 10 (1.8) Dia Typ .073 (1.8) Dia Typ .073 Single Pole 05 3 Double Pole .964" (24.5mm) Wirewrap or Extended PC 08 1.062" (27.0mm) Wirewrap or Extended PC (4.7) Typ .185 (1.8) Dia Typ .073 Four Pole Three Pole 07 (4.8) Typ .189 Epoxy Seal A (1.27) .050 Thk = (0.8) .031 If using as extended PC terminal, refer to the above footprints. Dimension A = terminal lengths as shown beside the terminal codes at the left. Tilt 03 (1.57) .062 Keylocks Solder Lug Tactiles 01 Rotaries Gold over Silver Slides A Pushbuttons Silver over Silver Programmable Illuminated PB W Rockers CONTACT MATERIALS & RATINGS Toggles Series M Bushing Mount Miniature Toggles OPTIONAL CAPS & CAP COLORS Material: Polyethylene Material: Polyethylene 25 AT434 Lever Cap for B Toggle 25 (8.0) Dia .315 (6.6) Dia .260 (11.5) .452 (13.1) .516 (13.5) .531 (12.3) .484 AT406 Lever Cap for B2 Toggle Material: Polyvinyl Chloride 25 (4.8) Dia .189 (12.0) .472 V Material: Polyvinyl Chloride 25 (5.0) Dia .197 (13.5) .532 R Touch * AT444 Conical Cap for S Bat Toggle Indicators C (18.0) .709 (18.5) .728 * AT415 and AT444 for use with S toggles only, not S2 or S3 toggles. Cap Colors Available: A Black B White C Red E Yellow www.nkkswitches.com F Green G Accessories * AT415 Lever Cap for S Bat Toggle Supplement B Blue A61 Toggles Series M Bushing Mount Miniature Toggles A TYPICAL SWITCH DIMENSIONS Rockers Solder Lug Single Pole Keyway Pushbuttons M2012SS1W01 Rotaries (0.9) .035 (8.9) .350 (10.5) .413 (9.4) .371 (13.0) .512 2 (0.8) Typ .031 (0.5) Typ .020 1 (2.0) .079 (4.5) .177 M2011 model does not have terminal 1. Solder Lug Double Pole (1.1) x (2.0) Typ .043 x .079 Keyway 1/4-40 Thd Keylocks Programmable Illuminated PB (2.8) Dia .110 (7.9) .311 3 (4.7) Typ .185 25 (4.7) Typ .185 25 (2.8) Dia .110 (12.7) .500 M2022SS1W01 (0.9) .035 (8.9) .350 (10.5) .413 (0.8) Typ .031 (0.5) Typ .020 (9.4) .371 6 3 5 2 4 1 (13.0) .512 (2.0) Typ .079 (4.8) .189 (4.5) .177 M2021 model does not have terminals 1 & 4. Solder Lug Three Pole Keyway Tactiles Slides (1.1) x (2.0) Typ .043 x .079 1/4-40 Thd (1.1) x (2.0) Typ .043 x .079 1/4-40 Thd 9 (4.7) Typ .185 25 Tilt (2.8) Dia .110 (10.5) .413 (17.5) .689 (0.9) .035 (8.9) .350 (11.5) .453 (0.8) Typ .031 (0.5) Typ .020 (4.5) .177 6 3 8 5 2 7 4 1 (13.0) .512 (2.0) Typ .079 (4.8) Typ .189 Solder Lug Indicators Touch M2032SS1W01 Four Pole Keyway (1.1) x (2.0) Typ .043 x .079 1/4-40 Thd (4.7) Typ .185 Supplement Accessories 25 (2.8) Dia .110 (22.3) .878 (10.5) .413 M2042SS1W01 A62 www.nkkswitches.com (0.9) .035 (8.9) .350 (11.5) .453 (0.8) Typ .031 (0.5) Typ .020 (4.5) .177 12 9 6 3 11 8 5 2 10 7 4 1 (4.8) Typ .189 (13.0) .512 (2.0) Typ .079 (6.0) Dia or .250 1/4-40 Thd or M6 P0.75 (8.0) .315 (12.0) Dia .472 (2.0) .079 AT516 O-ring for Splashproof Models Nitrile Butadiene Rubber (6.07) Dia (9.63) Dia .239 .379 (6.4) Dia (10.2) Dia .252 .402 (5.5) or .229 (1.7) .067 AT503M Hex Face Nut Brass/Chrome AT506M Locking Ring Steel with Zinc/Chromate AT508 Lockwasher Steel with Zinc/Chromate (not supplied with splashproof models) (12.1) Dia .476 M12 P1 (14.3) .563 (0.5) .020 (0.8) .031 (2.8) .110 (2.4) .094 (2.8) .110 AT401P O-ring for Splashproof Models Nitrile butadiene rubber M12 P1 (12.1) Dia .476 (17.5) Dia .689 (14.0) .551 (15.8) Dia .622 (13.8) Dia .543 (11.5) .453 (16.0) .630 AT527M Hex Nut Steel with Nickel Plating (12.1) .476 (18.2) Dia .717 (1.78) .070 Rotaries (1.5) .059 (9.5) .374 (1.0) .039 (16.0) .630 (0.5) .020 (1.0) .039 (2.0) .079 (1.5) .059 Slides (9.0) .354 Rockers AT509 Lockwasher Steel with Zinc/Chromate (not supplied with splashproof models) Pushbuttons AT507H for Inch AT507M for Metric Locking Ring Steel with Zinc/Chromate Programmable Illuminated PB AT513H for Inch AT513M for Metric Hex Nut Brass/Nickel Keylocks A STANDARD HARDWARE FOR SMALL & LARGE BUSHINGS Toggles Series M Bushing Mount Miniature Toggles OPTIONAL SPLASHPROOF BOOTS (15.3) .602 (19.3) .760 (23.8) .937 (0.5) .020 AT401A/H/S .461" (11.7mm) Boot, Nut and O-ring for B2 Toggle More details in Accessories section (16.0) Dia .630 (12.4) Dia .488 (18.0) Dia .709 (12.4) Dia .488 (18.0) Dia .709 (10.4) .409 (14.4) .567 (18.9) .744 (3.0) ~ (3.5) .118 .138 (1.57) .062 (3.0) ~ (3.5) .118 .138 (1.57) .062 (0.5) .020 AT4181 .732" (18.6mm) Boot, Nut and O-ring for B2 Toggle More details in Accessories section Indicators (2.0) (2.5) .079 ~ .098 (1.57) .062 (8.0) Dia .315 (8.0) Dia .315 (17.0) Dia .669 (17.5) Dia .689 (14.8) .583 (18.6) .732 (24.3) .957 (10.0) (11.7) .394 (13.2) .461 .520 (3.5) ~ (5.5) .138 .217 (1.57) .062 (1.0) .039 www.nkkswitches.com Tilt .315 (4.6) Dia .181 (6.7) Dia .264 (10.8) .425 Touch AT402S .567" (14.4mm) Boot for B Toggle Silicon Rubber Accessories (14.3) .563 (9.8) .386 (11.3) .445 AT402 .760" (19.3mm) Boot for B2 Toggle Silicon Rubber (8.0) Dia (13.8) Dia .543 (21.5) Dia .846 Supplement AT428 (M-metric H-Inch) .445" (11.3mm) Boot for S Toggle Silicon Rubber Tactiles Various optional nuts and ON-OFF plates are available; dimensions are shown in the Accessories & Hardware section. (4.57) ~ (6.3) .180 .248 (1.57) .062 A63 Bracket PC Mount Miniature Toggles A TYPICAL SWITCH M20 2 2 S S2 Poles Rotaries Slides Small Bushings SPDT S .413" (10.5mm) Bat A2 .280" (7.1mm) Smooth with Keyway 2 DPDT SP3T S2 .200" (5.08mm) Bat S2 .350" (8.9mm) Smooth with Keyway S3 .256" (6.5mm) Bat A1 .280" (7.1mm) Threaded with Keyway E .450" (11.4mm) Flatted S1 .350" (8.9mm) Threaded with Keyway E2 .256" (6.5mm) Flatted E4 .840" (21.3mm) Flatted Q .550" (14.0mm) Cone .640" (16.26mm) Cone .840" (21.3mm) Cone Circuits 2 ON NONE ON Q2 3 ON OFF ON Q4 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 *7 (ON) ON (ON) ON ON (ON) ( ) = Momentary Deduct bracket thickness of .020" (0.51mm) from above dimensions Toggle dimensions are based on use with a .350" (8.9mm) bushing; add .070" (1.78mm) to toggle length when combining with a .280" (7.1mm) bushing Locking Lever L Bushing For Locking Levers L2 .201" (5.1mm) Dia. Locking Lever Smooth with Keyway for Lever Lock * 3-ON circuits Tilt Tactiles Small Toggles 1 Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M Touch Standard Toggle & Bushing Combinations: Accessories Indicators SS2 & S2A2 IMPORTANT: Supplement Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings & ordering instructions are noted on the General Specifications page. A64 www.nkkswitches.com A ORDERING EXAMPLE B C Rockers 13 G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max Optional Caps Cap Colors B For S Bat Toggle A Black C Conical Cap for S Bat Toggle B White C Red E Yellow F Green G Blue Cap for Locking Lever No Code Nickel Plated Supplied with Switch A Black C Red G Blue Rotaries W Silver; Rated 6A @ 125V AC & 3A @ 250V AC Keylocks Contact Materials & Ratings Programmable Illuminated PB Pushbuttons G Toggles Series M Bracket PC Mount Miniature Toggles Terminals .250" (6.35mm) Straight PC with .465" (11.8mm) Bracket 15 .425" (10.8mm) Straight PC with .630" (16.0mm) Bracket 17 .964" (24.5mm) Straight PC with 1.150" (29.2mm) Bracket Tactiles 13 Slides With Bracket 25 .425" (10.8mm) Straight PC with .630" (16.0mm) Bracket 26 .750" (19.05mm) Straight PC with .953" (24.2mm) Bracket DESCRIPTION FOR TYPICAL ORDERING EXAMPLE M2022SS2G13-BC Touch .250" (6.35mm) Straight PC with .465" (11.8mm) Bracket Indicators 23 Tilt With Reinforced Bracket Red Cap on .413" (10.5mm) Bat Toggle www.nkkswitches.com Accessories .250" (6.35mm) Straight PC Terminals with Bracket .465" (11.8mm) Long .350" (8.9mm) Smooth Bushing with Keyway DPDT ON-NONE-ON Circuit Supplement Gold Contacts with 0.4VA Rating A65 Toggles Series M Bracket PC Mount Miniature Toggles POLES & CIRCUITS A Toggle Position ) = Momentary Down Center Connected Terminals Up Down Center Throw & Schematics Up Note: Terminal numbers are not actually on the switch. Pole Model SP M2012 M2013 M2015 M2018 M2019 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 OPEN 2-1 SPDT DP M2022 M2023 M2025 M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 OPEN 2-1 5-4 DPDT Keyway Keyway 2 (COM) 3 2 3 1 (COM) 1 5 6 4 For 3 Throw (3-On) Pole Model SP M2024 M2026 M2027 Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers ( Connected Terminals & Schematics Down Center Up ON (ON) ON ON ON ON ON (ON) (ON) External Connection 2 (in) 5 Slides 1 (out) External Connection 2 (in) 5 3 4 (out) 6 (out) 1 (out) 2-3 5-6 External Connection The SP3T model utilizes a double pole base. (out) External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) 2-3 5-4 External connection must be made during field installation. 3 4 (out) 6 (out) 2-1 5-4 External Conn 6 3 5 2 4 1 (out) Common (in) (out) Tactiles SMALL TOGGLES Tilt Important: Toggle length changes based on bushing selected. All illustrations are shown with .350" (8.9mm) long bushing. When using a .280" (7.1mm) long bushing, toggle length increases .070" (1.78mm). E2 .256" (6.5mm) Flatted E4 (5.0) .197 (4.2) .165 (2.5) .098 (6.5) .256 A66 25 (21.3) .840 .200" (5.08mm) Bat S3 .256" (6.5mm) Bat 25 (2.8) Dia .110 25 25 (2.7) Dia .106 (10.5) .413 .840" (21.3mm) Flatted (2.5) .098 S2 Q Q2 25 .640" (16.26mm) Cone (3.1) Dia .122 (16.26) .640 25 (2.54) .100 (11.4) .450 25 www.nkkswitches.com (5.08) .200 (6.5) .256 .550" (14.0mm) Cone (14.0) .550 .450" (11.4mm) Flatted E (2.7) Dia .106 (5.08) .200 (3.1) Dia .122 Supplement Accessories Indicators Touch Standard Material & Finish: Brass with Bright Chrome Contact factory for optional finishes. .413" (10.5mm) Bat S 25 Q4 .840" (21.3mm) Cone (3.1) Dia .122 (21.3) .840 25 A SMALL BUSHINGS S2 .350" (8.9mm) Smooth with Keyway (0.9) .035 (0.8) .031 (0.9) .035 (0.8) .031 (6.2) Dia .244 (6.2) Dia .244 (8.0) Dia .315 (2.5) .098 (7.1) .280 Pushbuttons (8.0) Dia .315 Rockers .280" (7.1mm) Smooth with Keyway (2.5) .098 (0.5) .020 (8.9) .350 (0.5) .020 Programmable Illuminated PB A2 When using this bushing, toggle length is increased by .070" (1.78mm). .280" (7.1mm) Threaded with Keyway S1 (0.9) .035 (0.9) .035 (0.8) .031 1/4-40 Thd (7.1) .280 Keylocks (8.0) Dia .315 (2.5) .098 (2.5) .098 (0.5) .020 (8.9) .350 When using this bushing, toggle length is increased by .070" (1.78mm). Maximum Panel Thickness with Standard Hardware: .031" (0.8mm) Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) Panel Cutouts For A2, S2, A1, or S1 Bushing with Keyway (5.6) .220 (6.5) Dia .256 (0.6) .024 (0.5) .020 Rotaries (8.0) Dia .315 1/4-40 Thd For A1 or S1 Bushing with Locking Ring Slides (0.8) .031 .350" (8.9mm) Threaded with Keyway Standard Hardware: (6.5) .256 (6.5) Dia .256 (2.2) Dia .087 2 Hex Nuts (AT513H) 1 Lockwasher (AT509) 1 Locking Ring (AT507H) Tactiles A1 Toggles Series M Bracket PC Mount Miniature Toggles For dimensions, see Accessories & Hardware section. Locking Mechanism Smooth with Keyway on-none-on on-none-(on) on-off-(on) on-on-(on) on-off-on on-on-on (on)-off-(on) (on)-on-(on) 2 positions lock 1 position locks 2 positions lock 3 positions lock 1 position locks Touch (2.5) .098 (0.8) .031 (8.0) Dia .315 25 (8.0) .315 (15.0) .591 (9.3) (7.0) .366 .275 (0.5) .020 No Code (4.6) Dia .181 (6.2) Dia .244 (0.9) .035 Cap for Locking Lever Supplied with Cap AT427 Material & Finish: Brass with Nickel Plating Lever Material & Finish: Brass with Chrome Plating www.nkkswitches.com Color Codes for Optional Anodized Aluminum Caps A G Black C Accessories (16.5) .650 Red Supplement (5.1) Dia .201 Indicators LL2 Tilt LOCKING LEVER & BUSHING Blue A67 Bracket PC Mount Miniature Toggles A CONTACT MATERIALS & RATINGS W Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Pushbuttons Rockers Toggles Series M Note: See Supplement section to find complete explanation of operating range. Programmable Illuminated PB A 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. TERMINALS Keylocks Straight PC Mount with Bracket 13 15 .250" (6.35mm) Terminal with .465" (11.8mm) Bracket Straight PC Mount with Reinforced Bracket 17 .425" (10.8mm) Terminal with .630" (16.0mm) Bracket 23 .964" (24.5mm) Terminal with 1.150" (29.2mm) Bracket 25 .250" (6.35mm) Terminal with .465" (11.8mm) Bracket 26 .425" (10.8mm) Terminal with .630" (16.0mm) Bracket .750" (19.05mm) Terminal with .953" (24.2mm) Bracket Tactiles Slides Rotaries Power Level or Logic Level Gold over Silver Tilt PCB footprints are on the following Typical Switch Dimension page. B * AT415 for S Bat Toggle C 25 (5.0) Dia .197 Material: Polyethylene (12.0) .472 (13.5) .532 Accessories Indicators Touch OPTIONAL CAPS & CAP COLORS * AT444 Conical Cap for S Bat Toggle Material: Polyethylene 25 (4.8) Dia .189 (11.5) .452 (13.1) .516 Supplement * AT415 and AT444 for use with S toggles only, not S2 or S3 toggles. Cap Colors Available: A68 A Black B White C Red www.nkkswitches.com E Yellow F Green G Blue A TYPICAL SWITCH DIMENSIONS Toggles Series M Bracket PC Mount Miniature Toggles Rockers Straight PC * Bracket (6.86) .270 (1.17) Typ .046 (1.17) .046 (3.2) .126 (4.5) .177 (4.5) .177 (4.8) .189 (1.17) Typ .046 (3.2) .126 (8.0) .315 Pushbuttons (0.9) .035 BRACKET LENGTH (4.8) .189 Keyway (7.1) .280 (1.17) Typ .046 (4.8) .189 (12.7) .500 TERMINAL LENGTH (0.5) Typ .020 (0.8) Typ .031 Programmable Illuminated PB BRACKET LENGTH Double Pole (4.7) Typ .185 (15.8) .622 (7.9) Typ .311 (4.7) Typ .185 3 (7.9) Typ .311 2 (4.7) Typ .185 1 3 6 2 5 1 4 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.8) Dia Typ .073 (1.5) Dia Typ .059 CL Terminal Code: Terminal Length: Bracket Length: 13 .250" (6.35mm) .465" (11.8mm) 15 .425" (10.8mm) .630" (16.0mm) 17 .964" (24.5mm) 1.150" (29.2mm) Rotaries (1.6) Typ .063 (2.4) Typ .095 (1.6) Typ .063 Keylocks M2012S2A2G13 Tactiles Straight PC * Reinforced Bracket (6.86) .270 Single Pole (6.35) .250 (9.1) .358 (2.4) Typ .095 (3.18) Typ .125 3 (9.53) Typ .375 2 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 (1.17) Typ .046 (4.8) .189 (6.35) .250 (12.7) .500 1 (4.7) Typ .185 (1.8) Dia Typ .073 (1.5) Dia Typ .059 3 6 2 5 1 4 CL Tilt TERMINAL LENGTH (0.5) Typ .020 (0.8) Typ .031 (4.7) Typ .185 Touch (1.17) Typ .046 (3.18) Typ .125 (9.53) Typ .375 (4.5) .177 (4.8) .189 (19.05) .750 M2012S2A2G23 Terminal Code: Terminal Length: Bracket Length: 23 .250" (6.35mm) .465" (11.8mm) 25 .425" (10.8mm) .630" (16.0mm) 26 .750" (19.05mm) .953" (24.2mm) www.nkkswitches.com Indicators (4.5) .177 Accessories (1.17) Typ .046 (1.17) .046 (0.9) .035 BRACKET LENGTH (4.8) .189 Keyway (7.1) .280 Supplement BRACKET LENGTH Double Pole Slides Single Pole A69 Angle PC Mount Miniature Toggles A TYPICAL SWITCH M20 1 2 S2 A2 Poles Small Toggles Small Bushings 1 SPDT S .413" (10.5mm) Bat A2 .280" (7.1mm) Smooth with Keyway 2 DPDT SP3T S2 .200" (5.08mm) Bat S2 .350" (8.9mm) Smooth with Keyway 3 3PDT S3 .256" (6.5mm) Bat A1 .280" (7.1mm) Threaded with Keyway E .450" (11.4mm) Flatted S1 .350" (8.9mm) Threaded with Keyway *4 4PDT DP3T E2 .256" (6.5mm) Flatted Toggle dimensions are based on use with a .350" (8.9mm) bushing; add .070" (1.78mm) to toggle length when combining with a .280" (7.1mm) bushing. * 4-pole available on vertical models only. Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Toggles Series M Tilt Tactiles Slides Circuits Locking Lever 2 ON NONE ON 3 ON OFF ON 5 ON NONE (ON) 8 (ON) OFF (ON) 9 ON OFF (ON) *4 ON ON ON *6 (ON) ON (ON) *7 ON ON (ON) L .201" (5.1mm) Dia. Locking Lever ( ) = Momentary Indicators Touch Smooth with Keyway for Lever Lock S2A2G30, S2A2G40, SS2G30, SS2G40, LL2G30, & LL2G40 with double and four pole bases only IMPORTANT: Accessories L2 Standard Toggle, Bushing, & Terminal Combinations: * 3-ON circuits available Supplement Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings & ordering instructions are noted on the General Specifications page. A70 Bushing For Locking Levers www.nkkswitches.com A ORDERING EXAMPLE Rockers 40 W Silver; Rated 6A @ 125V AC & 3A @ 250V AC G Gold; Rated 0.4VA max @ 28V AC/DC max A Gold over Silver; Rated 6A @ 125V AC & 0.4VA max @ 28V AC/DC max Cap Colors B For S Bat Toggle A Black C Conical Cap for S Bat Toggle B White C Red E Yellow F Green G Blue Cap for Locking Lever Nickel Plated Supplied with Switch A Black C Red G Blue Rotaries No Code Keylocks Optional Caps Contact Materials & Ratings Programmable Illuminated PB Pushbuttons G Toggles Series M Angle PC Mount Miniature Toggles 32 Right Angle PCB (1 Pole & 0.4VA Rating Only) 40 .150" (3.81mm) Vertical PC (1-4 Pole) 45 .100" (2.54mm) Vertical PC (1-4 Pole) Tactiles .150" (3.81mm) Right Angle PC (1-3 Pole) Touch Tilt 30 Slides Terminals DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Indicators M2012S2A2G40 Gold Contacts with 0.4VA Rating .280" (7.1mm) Smooth Bushing with Keyway .200" (5.08mm) Bat Toggle Accessories Vertical PC Terminals with .150" (3.81mm) Terminal Spacing Supplement SPDT ON-NONE-ON Circuit www.nkkswitches.com A71 Toggles Series M A POLES & CIRCUITS Programmable Illuminated PB Keylocks Toggle Position ) = Momentary Down Pole Pushbuttons Rockers ( Model M2012 * M2013 Center Connected Terminals Up Down Keyway Throw & Schematics Center Up Note: Terminal numbers are not actually on the switch. * Reverse circuits available for vertical mount SP & DP upon request. Keyway ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 OPEN 2-1 SPDT M2025 * M2028 M2029 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 OPEN 2-1 5-4 DPDT 3P M2032 M2033 M2035 M2038 M2039 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 OPEN 2-1 5-4 8-7 3PDT 4P M2042 M2043 M2045 M2048 M2049 ON ON ON (ON) ON NONE OFF NONE OFF OFF ON ON (ON) (ON) (ON) 2-3 5-6 8-9 11-12 OPEN 2-1 5-4 8-7 11-10 4PDT SP M2015 * M2018 M2019 M2022 * M2023 DP Slides Rotaries Angle PC Mount Miniature Toggles 2 (COM) 3 1 2 (COM) 3 1 2 3 5 5 3 1 2 5 1 6 (COM) 6 4 (COM) 8 9 7 8 11 9 4 6 4 7 12 10 For 3 Throw (3-On) Tilt Tactiles Connected Terminals & Schematics Pole Model Down Center SP M2024 ON M2026 (ON) M2027 ON ON ON ON Up ON (ON) (ON) Down Center External Connection 2 (in) 5 External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) 1 (out) Supplement Accessories Indicators Touch 2-3 5-6 DP M2044 ON M2046 (ON) M2047 ON ON ON ON ON (ON) (ON) External Connection 2 (in) 5 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) External connection must be made during field installation. A72 External Conn 6 3 5 2 4 1 (out) 3 4 (out) 6 (out) External Connection 2 (in) 5 External Connection 8 (in) 11 1 (out) (out) 2-1 5-4 1 (out) 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) 2-3 5-4 8-9 11-10 External connection must be made during field installation. www.nkkswitches.com External Connection 8 (in) 11 External Connection 2 (in) 5 3 4 (out) 6 (out) 7 (out) 9 10 (out) 12 (out) Common (in) 3 4 (out) 6 (out) 1 (out) External Connection 8 (in) 11 The DP3T model utilizes a four pole base. (out) External Connection 2 (in) 5 2-3 5-4 2-3 5-6 8-9 11-12 The SP3T model utilizes a double pole base. Up 2-1 5-4 8-7 11-10 (out) External Conn Common (in) (out) (out) 12 9 11 8 5 2 10 7 4 1 (out) 6 3 (out) Common (in) (out) A SMALL TOGGLES .200" (5.08mm) Bat S2 25 (2.8) Dia .110 .256" (6.5mm) Bat E (5.08) .200 .450" (11.4mm) Flatted (5.08) .200 25 .256" (6.5mm) Flatted E2 25 (2.54) .100 (2.7) Dia .106 (4.2) .165 (11.4) .450 (6.5) .256 25 (2.7) Dia .106 (10.5) .413 Rockers .413" (10.5mm) Bat Pushbuttons S3 S Programmable Illuminated PB Important: Toggle length changes based on bushing selected. All illustrations are shown with .350" (8.9mm) long bushing. When using a .280" (7.1mm) long bushing, toggle length increases .070" (1.78mm). (2.5) .098 25 (6.5) .256 Keylocks Standard Material & Finish: Brass with Bright Chrome Contact factory for optional finishes. SMALL BUSHINGS S2 (0.8) .031 .350" (8.9mm) Smooth with Keyway (0.8) .031 (6.2) Dia .244 (6.2) Dia .244 (2.5) .098 (2.5) .098 (0.9) .035 (7.1) .280 (8.0) Dia .315 Rotaries .280" (7.1mm) Smooth with Keyway Slides A2 (0.9) .035 (8.9) .350 (8.0) Dia .315 Tactiles When using this bushing, toggle length is increased by .070" (1.78mm). .280" (7.1mm) Threaded with Keyway S1 .350" (8.9mm) Threaded with Keyway Tilt A1 Toggles Series M Angle PC Mount Miniature Toggles (0.8) .031 1/4-40 Thd (8.0) Dia .315 When using this bushing, toggle length is increased by .070" (1.78mm). Maximum Panel Thickness with Standard Hardware: .031" (0.8mm) Maximum Panel Thickness with Standard Hardware: .102" (2.6mm) Panel Cutouts For A2, S2, A1 or S1 Bushing with Keyway (5.6) .220 (6.5) Dia .256 (0.6) .024 (0.9) .035 (8.9) .350 Indicators (8.0) Dia .315 Touch (2.5) .098 (0.9) .035 (7.1) .280 For A1 or S1 Bushing with Locking Ring (6.5) Dia .256 (2.2) Dia .087 Accessories (2.5) .098 1/4-40 Thd Standard Hardware: (6.5) .256 www.nkkswitches.com 2 Hex Nuts (AT513H) 1 Lockwasher (AT509) 1 Locking Ring (AT507H) Supplement (0.8) .031 For dimensions, see Accessories & Hardware section. A73 LOCKING LEVER & BUSHING LL2 Locking Mechanism Smooth with Keyway Rotaries on-none-on on-none-(on) on-off-(on) on-on-(on) on-off-on on-on-on (on)-off-(on) (on)-on-(on) 2 positions lock 1 position locks 2 positions lock 3 positions lock 1 position locks (0.8) .031 (8.0) Dia .315 (2.5) .098 25 (5.1) Dia .201 (16.5) .650 (8.0) .315 (15.0) .591 (9.3) (7.0) .366 .275 No Code Cap for Locking Lever (4.6) Dia .181 Color Codes for Optional Anodized Aluminum Caps Supplied with Cap AT427 Material & Finish: (6.2) Dia .244 A Brass with Nickel Plating Lever Material & Finish: (0.9) .035 G Brass with Chrome Plating Keylocks Programmable Illuminated PB Angle PC Mount Miniature Toggles A Pushbuttons Rockers Toggles Series M C Black Red Blue CONTACT MATERIALS & RATINGS W Slides G Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum Note: See Supplement section to find complete explanation of operating range. Tactiles A Power Level or Logic Level Gold over Silver 6A @ 125V AC or 0.4VA maximum @ 28V AC/DC maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. Tilt TERMINALS .150" (3.81mm) Right Angle PC (1-3 Pole) 32 Indicators Touch 30 3 2 (4.7) Typ .185 1 6 3 5 2 4 1 (4.7) Typ .185 (3.81) .150 9 8 7 6 5 4 3 2 1 Right Angle PCB with Reverse Circuit (1 Pole & 0.4VA Rating Only) (4.7) Typ .185 (3.81) Typ .150 1 (12.7) .500 Accessories (1.8) Dia Typ .073 (2.54) Typ .100 Supplement Single Pole (12.7) .500 (2.54) Typ .100 (1.8) Dia Typ .073 Double Pole (14.35) .565 (2.54) Typ .100 (1.8) Dia Typ .073 Three Pole Terminal dimensions are shown on the Typical Switch Dimensions pages which follow. A74 www.nkkswitches.com 2 3 (3.96) Typ .156 (9.27) .365 (2.54) Typ .100 (1.8) Dia Typ .073 (3.81) Typ .150 1 1 4 9 2 5 8 1 4 7 (2.54) Typ .100 (1.8) Dia Typ .073 (4.8) .189 3 3 6 2 5 1 1 4 3 Single Pole 12 2 5 8 11 1 4 7 10 9 2 5 8 1 4 7 (2.54) Typ .100 Double Pole (4.8) Typ .189 (3.81) Typ .150 (2.54) Typ .100 (1.8) Dia Typ .073 Four Pole (2.54) Typ .100 3 (4.8) Typ .189 6 9 12 2 5 8 11 1 4 7 10 (14.35) .565 (14.35) .565 (1.8) Dia Typ .073 (2.54) Typ .100 9 (14.35) .565 (4.8) Typ .189 6 (12.7) .500 (1.8) Dia Typ .073 6 Three Pole (2.54) Typ .100 2 (3.81) Typ .150 3 (2.54) Typ .100 (1.8) Dia Typ .073 Double Pole (2.54) Typ .100 (4.8) Typ .189 (14.35) .565 (2.54) Typ .100 (1.8) Dia Typ .073 (12.7) .500 (2.54) Typ .100 (3.81) Typ .150 (12.7) .500 .100" (2.54mm) Vertical PC (1-4 Pole) (2.54) Typ .100 6 5 (12.7) .500 Single Pole 45 3 2 6 (1.8) Dia Typ .073 (1.8) Dia Typ .073 (2.54) Typ .100 Three Pole Four Pole Rockers 2 3 Pushbuttons 3 (2.4) Typ .094 Programmable Illuminated PB .150" (3.81mm) Vertical PC (1-4 Pole) Rotaries 40 Keylocks A TERMINALS (Continued) Toggles Series M Angle PC Mount Miniature Toggles Terminal dimensions are shown on the Typical Switch Dimensions pages which follow. * AT444 Conical Cap for S Bat Toggle C 25 Material: Polyethylene 25 (5.0) Dia .197 (13.5) .532 (12.0) .472 Material: Polyethylene (4.8) Dia .189 (13.1) .516 (11.5) .452 Colors Available A Black E Yellow B White F Green C Red G Blue Tactiles * AT415 for S Bat Toggle Tilt B Slides OPTIONAL CAPS & CAP COLORS * AT415 and AT444 for use with S toggles only, not S2 or S3 toggles. (6.0) Dia or .250 1/4-40 Thd or M6 P0.75 (8.0) .315 AT509 Lockwasher (1 per switch, none with splashproof) Steel with Zinc/Chromate Indicators AT507H for Inch AT507M for Metric Locking Ring (1 per switch) Steel with Zinc/Chromate (12.0) Dia .472 (2.0) .079 Accessories AT513H for Inch AT513M for Metric Hex Nut (2 per switch) Brass/Nickel Touch STANDARD HARDWARE (6.4) Dia (10.2) Dia .252 .402 (9.0) .354 (1.5) .059 (1.7) .067 (0.8) .031 www.nkkswitches.com Supplement (5.5) or .229 (0.5) .020 A75 Toggles Series M Angle PC Mount Miniature Toggles A TYPICAL SWITCH DIMENSIONS Single Pole Rockers .150" (3.81mm) Right Angle PC Pushbuttons 1 2 3 (7.9) .311 (4.3) .169 Programmable Illuminated PB (2.9) .114 (1.4) Typ .055 (5.08) .200 (6.86) .270 (0.4) .016 (1.09) .043 (12.7) .500 (7.32) .288 (1.27) .050 (0.8) Typ .031 (4.7) Typ .185 (13.0) .512 M2012S2A2G30 .150" (3.81mm) Right Angle PC Rotaries Keylocks (6.2) Dia .244 Keyway Double Pole (6.2) Dia .244 Keyway 4 5 6 1 2 3 (12.7) .500 Slides (4.3) .169 Tactiles (2.9) .114 (1.4) Typ .055 (5.08) .200 (6.86) .270 (7.32) .288 (0.4) .016 (1.09) .043 (12.7) .500 (0.8) Typ .031 (4.7) Typ .185 (1.27) Typ .050 (3.81) .150 (13.0) .512 Tilt M2022S2A2G30 Touch .150" (3.81mm) Right Angle PC (6.2) Dia .244 (0.9) .035 Indicators Keyway Three Pole 7 8 9 4 5 6 1 2 3 (17.5) .689 Accessories (4.3) .169 Supplement (2.9) .114 (1.4) Typ .055 (5.08) .200 (6.86) .270 (8.0) .315 M2032S2A2G30 A76 www.nkkswitches.com (0.4) .016 (1.8) .071 (14.35) .565 (1.27) Typ .050 (3.81) Typ .150 (13.0) .512 (0.8) Typ .031 (4.7) Typ .185 A TYPICAL SWITCH DIMENSIONS Right Angle PCB Rockers Single Pole * Reverse Circuit Toggles Series M Angle PC Mount Miniature Toggles (7.9) .311 (4.55) .179 (0.9) .035 (6.2) .245 (8.9) (6.86) .270 .350 (1.4) Typ .055 (5.08) .200 (0.4) .016 (9.3) .365 3 2 (1.4) Typ .055 (3.96) Typ .156 (2.7) .106 (0.8) .031 (8.5) .335 1 (13.0) .512 M2012S2A2G32 .150" (3.81mm) Vertical PC Rotaries Single Pole (6.2) Dia .244 Keyway 3 25 (13.0) .512 2 (6.86) .270 (7.32) .288 (0.4) .016 (1.1) .043 (12.7) .500 (0.8) Typ .031 (3.81) Typ .150 (2.7) .106 (1.27) .050 (7.9) .311 Tactiles (1.4) Typ .055 (5.08) .200 Slides 1 (2.7) Dia .106 Programmable Illuminated PB (6.2) Dia .244 Keylocks (2.7) Dia .106 Keyway Pushbuttons 25 Tilt M2012S2A2G40 .150" (3.81mm) Vertical PC Touch Double Pole (1.4) Typ .055 (5.08) .200 (6.86) .270 (7.32) .288 (0.4) .016 (1.1) .043 (12.7) .500 (0.8) Typ .031 (3.81) Typ .150 (2.7) .106 2 4 1 (4.8) .189 (12.7) .500 (13.0) .512 (1.27) Typ .050 Accessories (2.7) Dia .106 3 5 Supplement 25 6 Indicators (6.2) Dia .244 Keyway M2022S2A2G40 www.nkkswitches.com A77 Toggles Series M Angle PC Mount Miniature Toggles A TYPICAL SWITCH DIMENSIONS Three Pole Rockers .150" (3.81mm) Vertical PC (6.2) Dia .244 Keyway (0.9) .035 Pushbuttons 9 25 Programmable Illuminated PB (2.7) Dia .106 (1.4) Typ .055 (5.08) .200 (8.0) .315 (6.86) .270 (0.4) .016 (1.8) .071 (14.35) .565 (0.8) Typ .031 (3.81) Typ .150 (2.7) .106 6 3 8 5 2 7 4 1 (13.0) .512 (4.8) Typ .189 (17.5) .689 (1.27) Typ .050 M2032S2A2G40 Rotaries Keylocks .150" (3.81mm) Vertical PC Four Pole (6.2) Dia .244 Keyway (0.9) .035 25 Slides (2.7) Dia .106 (1.4) Typ .055 (5.08) .200 (8.0) .315 (0.8) Typ .031 (3.81) Typ .150 (2.7) .106 9 6 3 11 8 5 2 10 7 4 1 (4.8) Typ .189 (22.3) .878 Tactiles (6.86) .270 (0.4) .016 (1.8) .071 (14.35) .565 12 Tilt M2042S2A2G40 Touch .100" (2.54mm) Vertical PC Single Pole (6.2) Dia .244 Keyway Indicators 3 25 2 (13.0) .512 1 (2.7) Dia .106 Supplement Accessories (1.4) Typ .055 (5.08) .200 (6.86) .270 M2012S2A2G45 A78 www.nkkswitches.com (7.32) .288 (0.4) .016 (1.1) .043 (12.7) .500 (0.8) Typ .031 (2.54) Typ .100 (7.9) .311 (2.7) .106 (1.27) .050 (13.0) .512 (1.27) Typ .050 A TYPICAL SWITCH DIMENSIONS .100" (2.54mm) Vertical PC Rockers Double Pole Toggles Series M Angle PC Mount Miniature Toggles (1.4) Typ .055 (5.08) .200 (6.86) .270 (7.32) .288 (0.4) .016 (1.1) .043 (12.7) .500 2 4 1 (2.7) .106 (0.8) Typ .031 (2.54) Typ .100 (13.0) .512 (1.27) Typ .050 (4.8) .189 (12.7) .500 M2022S2A2G45 Three Pole 25 (2.7) Dia .106 (1.4) Typ .055 (5.08) .200 (8.0) .315 (0.8) Typ .031 (2.54) Typ .100 (2.7) .106 6 3 8 5 2 7 4 1 (13.0) .512 (4.8) Typ .189 (17.5) .689 (1.27) Typ .050 Tactiles (6.86) .270 (0.4) .016 (1.8) .071 (14.35) .565 9 Rotaries (0.9) .035 Slides (6.2) Dia .244 Keyway .100" (2.54mm) Vertical PC Programmable Illuminated PB (2.7) Dia .106 3 5 Keylocks 25 6 Pushbuttons (6.2) Dia .244 Keyway (0.9) .035 (1.4) Typ .055 (5.08) .200 (6.86) .270 (8.0) .315 (0.4) .016 (1.8) .071 (14.35) .565 (0.8) Typ .031 (2.54) Typ .100 6 3 8 5 2 10 7 4 1 (2.7) .106 (4.8) Typ .189 (22.3) .878 (13.0) .512 Indicators (2.7) Dia .106 9 11 (1.27) Typ .050 Accessories 25 12 M2042S2A2G45 www.nkkswitches.com A79 Supplement (6.2) Dia .244 Keyway .100" (2.54mm) Vertical PC Touch Four Pole Tilt M2032S2A2G45 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: NKK Switches: M2013S2A2G40 M2012SA2G30 M2012EA2G30 M2012ES2G30 M2012ES2G40 M2012S2A2W40 M2032ES1G40 M2012S2A1G32 M2013S2A2W30 M2022LL2W30 M2022SA2G30 M2022SA2G40 M2025SA2G30/305 M2033S2A2G40 M2042SA1G40 M2032S2A2G30 M2012LL2G40-RO M2012S2S2W30 M2012S2S2W40 M2012SS2G45 M2013SA2A40 M2013SA2W40 M2013SS1G30 M2013SS1G45 M2013SS2G45 M2018ES1A40 M2018SA2G40 M2018SS1W40 M2018SS1W45 M2022LL2A30 M2022S3A2W40 M2022SA1W30 M2023ES2W40RO M2023S2A2W30 M2024SS2G45 M2032S2A2W40-RO M2042SS1G45 M2042SS1W45 M2022SS1W30-BA-RO M2012S2A1W30 M2022S2A2W40/UC M2013S2A2G40-RO M2012SS1G45-RO M2022SS2G45 M2027S2A2G30 M2048SS2W40/CUL M2049SS2W40/CUL M2022SA2W40 M2032E2S1G40 M2024SS2G30 M2022SS1W30-RO M2033SS1A40 M2012SA2G32 M2015S2A2A40 M2015S2A2W40 M2024S3A2A30 M2026SA2G40 M2032S2A2W30 M2046SA2G40 M2012LL2A40 M2024S3S1G30 M2012S2S1W40 M2013S2S1W40 M2042SS1G45-BA M2012S2S1W30 M2027S2A2W30 M2022S2S1W40 M2012LL2G45 M2013SS1G40 M2012S2A2G45 M2022LL1G45 M2012S2A2W45 M2023S2A2G40 M2012SA2G40 M2012S2A2W30 M2012LL1G45 M2022S2A2G45 M2032S2A2W40 M2022LL1G30 M2022SA1W40 M2029ES1G30 M2012ES2W40 M2012S2A1G40/UC M2012SS2G30/U M2018S2A2G30 M2013SS2G30 M2022SS2W45 M2012SS1W40 M2029ES2G30 M2013LL2G30 M2029SS2G30 M2022SS1W40 M2021S2A2G40 M2012E2A2W40 M2023SS1G30 M2024SS1W40 M2018ES1G30 M2032S2A2G40 M2012SA2W40 M2012S2A2A30/UC