21349697598006 - HARTING TECHNOLOGY GROUP

CRCW0201 e3

www.vishay.com Vishay

Revision: 07-Mar-17 1Document Number: 20052

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Lead (Pb)-free Commodity Thick Film Chip Resistors

FEATURES

• High volume product suitable for commercial

applications

• Pure tin solder contacts on Ni barrier layer

provides compatibility with lead (Pb)-free and

lead containing soldering processes

• Metal glaze on high quality ceramic

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

Notes

• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over

operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.

Note

(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.

STANDARD ELECTRICAL SPECIFICATIONS

MODEL

CASE

SIZE

INCH

CASE

SIZE

METRIC

POWER RATING

P70

LIMITING

ELEMENT

VOLTAGE

Umax.

ACRMS/DC

TEMPERATURE

COEFFICIENT

ppm/K

TOLERANCE

RESISTANCE

RANGE



SERIES

CRCW0201 0201 RR 0603M

0.05 30

± 200

± 0.5

10.0 to 10M

E24; E96

-200 / +400 1.0 to 9.76

± 100

± 1

47.0 to 1M

E24; E96± 200 10.0 to 10M

-200 / +400 1.0 to 9.76

± 200

± 5

10.0 to 10M

E24

-200 / +400 1.0 to 9.1

Zero-Ohm-Resistor: Rmax. = 50 m, Imax. at 70 °C = 1.0 A

TECHNICAL SPECIFICATIONS

PARAMETER UNIT CRCW0201

Rated Dissipation at 70 °C (1) W0.05

Operating Voltage Umax. ACRMS/DC V 30

Insulation Voltage Uins (1 min) V 50

Insulation Resistance > 109

Operating Temperature Range °C -55 to +155

Weight mg 0.17

CRCW0201 e3

www.vishay.com Vishay

Revision: 07-Mar-17 2Document Number: 20052

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DIMENSIONS in millimeters

Note

• No marking for 0201 size.

PART NUMBER AND PRODUCT DESCRIPTION

PART NUMBER: CRCW02011K00FNED

MODEL VALUE TOLERANCE TCR PACKAGING

CRCW0201 R = decimal

K = thousand

M = million

0000 = jumper

D = ± 0.5 %

F = ± 1.0 %

J = ± 5.0 %

Z = jumper

K = ± 100 ppm/K

N = ± 200 ppm/K

X = -200 ppm/K / +400 ppm/K

0 = jumper

PRODUCT DESCRIPTION: CRCW0201 100 1K0 1 % ET7 e3

CRCW0201 100 562R 1 % ET7 e3

MODEL TCR RESISTANCE

VALUE

TOLERANCE

VALUE PACKAGING LEAD (Pb)-FREE

CRCW0201 ± 200 ppm/K

± 100 ppm/K

- 200/+ 400

ppm/K

1R0 = 1 

10R = 10 

1K0 = 1 k

10K = 10 k

1M0 = 1 M

0R0 = jumper

± 0.5 %

± 1 %

± 5 %

ET7

EF4

ET2

e3 = pure tin

termination finish

PACKAGING

MODEL CODE QUANTITY CARRIER TAPE WIDTH PITCH REEL DIAMETER

CRCW0201

ED = ET7 10 000 Paper tape acc.

to IEC 60068-3

Type I

8 mm 2 mm

180 mm/7"

EI = ET2 20 000 254 mm/10"

EE = EF4 50 000 330 mm/13"

SIZE DIMENSIONS SOLDER PAD DIMENSIONS

INCH METRIC L W H T1 T2 a b l

0201 0603 0.6 ± 0.05 0.3 ± 0.05 0.23 ± 0.05 0.15 ± 0.05 0.10 ± 0.05 0.28 0.43 0.23

C R C W 0 2 0 1 1 K 0 0 F K E D

CRCW0201 e3

www.vishay.com Vishay

Revision: 07-Mar-17 3Document Number: 20052

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

DERATING

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC

60068-2

TEST

METHOD

TEST

PROCEDURE REQUIREMENTS

PERMISSIBLE CHANGE (R)

Stability for product types:

1  to 10 M

CRCW0201 e3

4.5 - Resistance - ± 0.5 %; ± 1 %; ± 5 %

4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown

4.13 58 (Td) Solderability

Solder bath method;

Sn60Pb40

non activated flux;

(235 ± 5) °C

(2 ± 0.2) s

Good tinning ( 95 % covered)

no visible damage

Solder bath method;

Sn96.5Ag3Cu0.5

non-activated flux;

(245 ± 5) °C

(3 ± 0.3) s

Good tinning ( 95 % covered)

no visible damage

4.8.4.2 - Temperature coefficient (20 / -55 / 20) °C and

(20 / 125 / 20) °C

± 100 ppm/K,

± 200 ppm/K,

-200 ppm/K / +400 ppm/K

4.32 21 (Uu3) Shear (adhesion) 9 N No visible damage

4.33 21 (Uu1) Substrate bending Depth 2 mm; 3 times

No visible damage,

no open circuit in bent position

± (0.5 % R + 0.05 )

4.19 14 (Na) Rapid change

of temperature

30 min. at -55 °C;

30 min. at 125 °C

5 cycles ± (0.5 % R + 0.05 )

1000 cycles ± (1 % R + 0.05 )

4.23 - Climatic sequence: -

± (2 % R + 0.1 )

4.23.2 2 (Ba) Dry heat 125 °C; 16 h

4.23.3 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 1 cycle

4.23.4 1 (Aa) Cold -55 °C; 2 h

4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h

4.23.6 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 5 cycles

4.23.7 - DC load U =  Umax.

- 50 0 50 100 150

70 125

Ambient Temperature amb in °C

Fraction of Rated Dissipation P70 in %

100

P70 x R

CRCW0201 e3

www.vishay.com Vishay

Revision: 07-Mar-17 4Document Number: 20052

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

All tests are carried out in accordance with the following specifications:

• EN 60115-1, generic specification

• EN 140400, sectional specification

• EN 140401-802, detail specification

• IEC 60068-2-x, environmental test procedures

Packaging of components is done in paper tapes according to IEC 60286-3.

4.25.1 - Endurance at 70 °C

U =  Umax.;

1.5 h on; 0.5 h off;

70 °C; 1000 h ± (2 % R + 0.1 )

70 °C; 8000 h ± (4 % R + 0.1 )

4.18.2 58 (Td) Resistance to

soldering heat

Solder bath method

(260 ± 5) °C; (10 ± 1) s ± (1 % R + 0.05 )

4.35 - Flamability,

needle flame test

IEC 60695-11-5;

10 s No burning after 30 s

4.24 78 (Cab) Damp heat, steady state (40 ± 2) °C; (93 ± 3) % RH; 56 days ± (2 % R + 0.1 )

4.25.3 - Endurance at upper

category temperature 155 °C, 1000 h ± (2 % R + 0.1 )

4.29 45 (XA) Component

solvent resistance

Isopropyl alcohol;

50 °C; method 2 No visible damage

4.22 6 (Fc) Vibration, endurance

by sweeping

f = 10 Hz to 2000 Hz;

x, y, z  1.5 mm;

A  200 m/s2;

10 sweeps per axis

± (0.5 % R + 0.05 )

TEST PROCEDURES AND REQUIREMENTS

EN 60115-1

CLAUSE

IEC

60068-2

TEST

METHOD

TEST

PROCEDURE REQUIREMENTS

PERMISSIBLE CHANGE (R)

Stability for product types:

1  to 10 M

CRCW0201 e3

P70 x R

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 01-Jan-2019 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.