OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 1 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
RoHS
Description:
The OPIA series optocouplers are d esigned for applications that use an analog output (Phototransistor or
Photodarlington) in a dual-i n-line package. A wide selection of configurations are available. With typical isolation
voltage of 5,000 Volts(RMS), these products meet typical power system isolation requirements.
Theory of operation: The LED transmitt er is u sed to illuminate the Photosensor providing electrical isolation
between two power syste ms while maintaining the ability to transmit information from one power syste m to the
other. In many applications, analog signal levels may be required to be transmitted between two power systems
while maintaining isolation between the power systems up to 5,000 volts(RMS). A variety of LED and photosensor
configurations are available depending on the system requirements.
The ratio Current Transfer Ratio (CTR) is determined by using the output current and input current for analog
photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device.
All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number.
Example: OPIA817DTUE is a 4-Pin DIP shipped in a tube (T U).
Features:
• 5,000 Vrms electrical isolation
• Choice of a Single and Dual LE D
• Phototransistor or Photodarlington Sensor
• Low-cost plastic Dual-In-Line (DIP) package
Approval Agency:
• UL Certification No: E58730
• VDE No: 40026625 40026536, 40026654
Applications:
• High voltage isolation: 5,000 Volts RMS
• PCBoard power system isolation
• Industrial equipment power isolation
• Medical equipment power isolation
• Office equipment
200100*
10
20 ==
−
−
=mA
mA
Curren
t
LED CurrentrPhotosenso
CTR
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 2 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Analog Output Devices Ordering Information
Part Number Isolation Voltage
Max. (Vrms) CTR
Min/Typ/Max Typ. Tr / Tf (µs)
RL = 100 ohms Package Configuration
OPIA817D 5,000 50 / - / 600 4 / 3 4-Pin DIP A K—C E
OPIA814D 5,000 60 / - / 600 5 / 4 4-Pin DIP A K, K A—C E
OPIA815D 5,000 70 / - / - 80 / 72 4-Pin DIP A K—C E (Dar)
OPIA4010D 5,000 600 / - / 9,000 60 / 50 4-Pin DIP A K—C E (Dar)
OPIA1210D 5,000 50 / - / 600 2 / 3 4-Pin DIP A K—C E
Configuration: Definition of Terms
LED Identification—Sensor Id entification
Configuration
Information LED A = Anode K = Cathode
Sensor B = Base C = Collector E = Emitter (Dar) = Photodarlington
Packaging Part Number Suffix: TU = Shipped in Tubes Example:
OPIA817DTUE
Part Number Pin #
1 2 3 4
OPIA817 A K E C
OPIA814 A-K K-A E C
OPIA815 A K E C
OPIA4010 A K E C
OPIA1210 A K E C
Package Outline Dimensions and Schematics: Top-View
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 3 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Absolute Maximum Ratings (TA = 25o C unless otherwise noted)
Storage Temperature
-55° C to +125° C
Operating Temperature -30° C to +100° C
Isolation voltage (1 minute) 5,000 Vrms
Total Package Power Dissipation 200 mW
Lead Soldering Temperature ( 1/16” (1.6 mm) from case for 5 seconds with soldering iron) 260° C
Input Diode
Continuous For ward Curr ent
50 mA
Peak Forward current (1 µs pulse width, 300 pps)
1 A
Reverse Voltage
OPIA817, OPIA815, OPIA4010, OPIA1210
OPIA814, OPIA4010
6 V
-
Power Dissipation 70 mW
Output Phototransistor
Collector-Emitter Voltage
OPIA817, OPIA814
OPIA4010
OPIA815
OPIA1210
60 V
300 V
35 V
350 V
Emitter-Collector Voltage
OPIA817, OPIA814, OPIA815
OPIA4010
OPIA1210
6 V
0.1 V
7 V
Collector Current
OPIA817, OPIA814, OPIA1210
OPIA4010
OPIA815
50 mA
150 mA
80 mA
Power Dissipation
All except the part numbers noted below
OPIA4010
150 mW
200 mW
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 4 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Electrical Characteristics
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS
Input Diode
VF Forward Voltage
All except those noted belo w
OPIA1210
-
1.0
1.2
1.2
1.4
1.3
V
IF = 20 mA
IF = 10 mA
VFM Peek Forward Voltage
OPIA814, OPIA4010
OPIA1210
-
-
-
-
3.5
3.0
V
IFM = 500 mA
IR
Reverse Current
All except those noted belo w
OPIA814
OPIA1210
-
-
-
-
-
-
10
-
10
µA
VR = 4 V
-
VR = 5 V
Ct Terminal Capacitance
All except those noted belo w
OPIA815
-
-
30
30
-
250
pf
V = 0.0 V, f = 1K Hz
V = 0.0 V, f = 1K Hz
Output Phototransistor
ICEO Collector Dark Current
OPIA817, OPIA814
OPIA1210
-
-
-
10
100
200
nA
IF = 0 mA, VCE = 20 V
IF = 0 mA, VCE = 300 V
VCE(SAT)
Collector-Emitter Saturation Voltage
OPIA817
OPIA814
OPIA1210
-
-
-
0.1
0.1
-
0.2
0.3
0.4
V
IF = 20 mA, IC = 1 mA
IF = 20 mA, IC = 1 mA
IF = 8 mA, IC = 2.4 mA
fC Cutt-Off Frequency
All except those noted belo w
OPIA817, OPIA814, OPIA1210
-
-
-
80
-
-
K Hz
VCC = 5 V, IC = 2 mA, RL = 100 Ω
tR
Rise Time
OPIA817
OPIA814
OPIA1210
-
-
-
4
5
2
18
20
-
µs
VCC = 2 V, IC = 2 mA, RL = 100 Ω
VCC = 2 V, IC = 2 mA, RL = 100 Ω
VCC = 10 V, IC = 2 mA, RL = 100 Ω
tF
Fall Time
OPIA817D
OPIA814
OPIA1210
-
-
-
3
4
3
18
20
-
µs
VCC = 2 V, IC = 2 mA, RL = 100 Ω
VCC = 2 V, IC = 2 mA, RL = 100 Ω
VCC = 10 V, IC = 2 mA, RL = 100 Ω
Continued on Next Page
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 5 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Electrical Characteristics - Continued from Previous Page
SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS
Output PhotoDarlington
ICEO Collector Dark Current
OPIA4010
OPIA815
-
-
-
-
1.0
1.0
µA
IF = 0 mA, VCE = 200 V
IF = 0 mA, VCE = 10 V
VCE(SAT) Collector-Emitter Saturation Voltage
OPIA815
OPIA4010
-
-
0.8
-
1.0
1.5
V
IF = 20 mA, IC = 5 mA
IF = 20 mA, IC = 5 mA
fC Cut-Off frequency
OPIA815
OPIA4010
1.0
-
6.0
7.0
-
-
K Hz
VCC = 2 V, IC = 20 mA, RL = 100 Ω
VCC = 5 V, IC = 2 mA, RL = 100 Ω
tr Rise Time
OPIA815
OPIA4010
-
-
80
60
300
300
µs
VCC = 2 V, IC = 20 mA, RL = 100 Ω
VCC = 2 V, IC = 20 mA, RL = 100 Ω
tf Fall Time
OPIA815
OPIA4010
-
-
72
50
250
250
µs
VCC = 2 V, IC = 20 mA, RL = 100 Ω
VCC = 2 V, IC = 20 mA, RL = 100 Ω
Coupled Characteristics
CTR
Current Transfer Ratio
OPIA817, OPIA1210
OPIA814
OPIA815
OPIA4010
50
60
70
600
-
-
-
-
600
600
-
9,000
%
IF = 5.00 mA, VCE = 5.0 V
IF = 1.00 mA, VCE = 2.0 V
IF = 0.05 mA, VCE = 3.3 V
IF = 1.00 mA, VCE = 2.0 V
Cf Floating Capacitance - 0.6 1.0 pF V = 0.0 V, f = 1M Hz
RISO Isolation Resistance 5X1010 1011 - ohm C500V, 40% to 60%RH
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 6 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA817
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 7 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA817
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 8 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA814
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 9 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA814
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 10 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA815
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 11 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA815
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 12 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPI412
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 13 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPI412
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 14 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA1210
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 15 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
OPIA1210
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com
Issue A.5 8/09
Page 16 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Quality / Reliability Requirements
Note: This is to be performed when a change occurs to form, fit or function.
Government and Industry Standard
Compliance Requirements
European Union’s Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC
Parameter Failure Criteria Conditions
HTRB D IC(OFF) ± 10% 11 samples after 500Hrs
0 Fail @ VCE = 5.0VDC, Ta = 70°C
HTFB D IC(ON) ± 10% 50 samples after 96Hrs
0 Fail @ Max PD, Ta = 25°C
MTTF @ 90% confidence 150,000 Min. @ 25°C, 25mADC
Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020 B
Lead Solderability 0 Fail per Method 208 of MIL-STD-202.
Glass Transition of body 125°C Min. DSC test method
Temperature Humidity-Bias ± 20% 85°C, 85%RH, 500Hrs, 80% min Iceo
Temperature Cycle ± 20% per Method 1010.7 of MIL-STD-883E
High Temperature Storage ± 20% 85°C, 500Hrs
Autoclave 0 Fail
TA = 121°C, Pressure = 15psi, Humidit y
= 100%, Time = 96Hrs
Label Identification
DESCRIPTION:
Size: 3” (7.4 cm) X 2.2” (5.5 cm)
Lettering shall be black on white background.
Format shall be as:
Notes:
1. The DATE CODE is a 4-digit code for date of manufacture whe re YY is
the last two digits of the year, and WW is week n umber of
manufacture.
2. The LOT I.D. is the manufacturing location lot identification where Y is
the year of manufacture, NNNN is a sequential lot identifier, and DDD
is the day of the year of manufacture. – or use equivalent label format.
Carrollton, TX, USA
MADE IN TAIWAN
OPTEK P/N __OPIA817D-TU__
IIIIIIIIIIIIIIIIIIIII
QTY. ________N/A_________
IIIIIIIIIIIIIIIIIIIII
DATE CODE _____(YYWW)___
IIIIIIIIIIIIIIIIIIIII
LOT I.D. ____(Y-NNNNDDD)__
IIIIIIIIIIIIIIIIIIIII
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue A.5 8/09
Page 17 of 17
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPIA814, OPIA815, OPIA817
OPIA1210, OPIA4010
DIP Package
Packaging Information:
Tube Packaging Specifications (TU):
Quantity: 4-pin: 100pcs/tu be
DIMENSIONS ARE IN: INCHES [MILLIMETERS]
TOLERANCE: ± 0.008 INCHES
[± 0.2 MILLIMETERS]
