UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com BUCK CURRENT/VOLTAGE FED PUSH-PULL PWM CONTROLLERS Check for Samples: UC2827-1, UC2827-2, UC3827-1, UC3827-2 FEATURES 1 * * * * * * * * DESCRIPTION Ideal for Multiple Output and/or High Voltage Output Voltage Converters Up to 500 kHz Operation High Voltage, High Current Floating Driver for Buck Converter Stage UC3827-1 Current Fed Controller has Push-Pull Drivers with Overlapping Conduction Periods UC3827-2 Voltage Fed Controller has Push-Pull Drivers with Nonoverlapping Conduction Periods Average Current Mode, Peak Current Mode or Voltage Mode with Input Voltage Feedforward Control for Buck Power Stage Wide Bandwidth, Low Offset, Differential Current Sense Amplifier Precise Short Circuit Current Control The UC3827 family of controller devices provides an integrated control solution for cascaded buck and push-pull converters. These converters are known as current fed or voltage fed push-pull converters and are ideally suited for multiple output and/or high voltage output applications. In both current fed and voltage fed modes, the push-pull switches are driven at 50% nominal duty cycles and at one half the switching frequency of the buck stage. In the current fed mode, the two switches are driven with a specified over-lap period to prevent ringing and voltage stress on the devices. In the voltage fed mode, the two switches are driven with a specified gap time between the switches to prevent shorting the transformer across the energy storage capacitor and to prohibit excessive currents flowing through the devices. The converter's output voltage is regulated by pulse width modulation of the buck switch. The UC3827 contains complete protection and PWM control functions for the buck converter. Easy control of the floating switch is accomplished by the floating drive circuitry. The gate drive waveform is level shifted to support an input voltage up to 72 VDC. BLOCK DIAGRAM VEAOCEA+ 10 12 CEAO 6 RAMP 5 Voltage Error Amplifier 14 VEA- 16 CEA- 13 CSAO 7 CSA+ 8 CSA- 9 SS 4 0.7 V Current Error Amplifier PWM Comparator + VEA+ RD Flying Driver +3 V S ILIM Comparator Current Sense Amplifier SYNC 19 CT 18 OSC RT 17 500 kHz MAX REF 15 VCC 23 GND 11 SS INHBT Q 1 V+ 2 BUCK 3 SRC 21 PGND 24 PUSH 22 PULL OSC UV Q DELAY T Push/Pull Drivers Q REF & UVLO UVLO DELAY 20 DELAY 1 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2011, Texas Instruments Incorporated UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com DESCRIPTION (CONTINUED) The UC3827 can be set up in traditional voltage mode control using input voltage feedforward technique or in current mode control. Using current mode control prevents potential core saturation of the push-pull transformer due to mismatches in timing and in component tolerances. With average current mode control, precise control of the inductor current feeding the push-pull stage is possible without the noise sensitivity associated with peak current mode control. The UC3827 average current mode loop can also be connected in parallel with the voltage regulation loop to assist only in fault conditions. Other valuable features of the UC3827 include bidirectional synchronization capability, user programmable overlap time (UC3827-1), user programmable gap time (UC3827-2), a high bandwidth differential current sense amplifier, and soft start circuitry. ORDERING INFORMATION (1) TA = TJ -40C to 85C 0C to 70C (1) PACKAGES PUSH-PULL TOPOLOGY SOIC-24 PDIP-24 PLCC-28 - Current Fed UC2827DW-1 UC2827N-1 Voltage Fed UC2827DW-2 UC2827N-2 - Current Fed UC3827DW-1 UC3827N-1 UC3827Q-1 Voltage Fed UC3827DW-2 UC3827N-2 - The DW and Q packages are also available taped and reeled. Add a TR suffix to the device type (i.e., UC2827DWTR-1). THERMAL INFORMATION THERMAL METRIC (1) JA Junction-to-ambient thermal resistance JCtop Junction-to-case (top) thermal resistance (2) (1) (2) UC2827-1, UC2827-2, UC3827-1, UC3827-2 UC2827-1, UC2827-2, UC3827-1, UC3827-2 N J 24 PINS 24 PINS 60 70 to 80 30 28 UNITS C/W The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDEC-standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. THERMAL INFORMATION UC2827-1, UC2827-2, UC3827-1, UC3827-2 THERMAL METRIC DW Junction-to-ambient thermal resistance (2) JA JCtop (1) (2) (3) 2 Junction-to-case (top) thermal resistance (3) UC2827-1, UC2827-2, UC3827-1, UC3827-2 UNITS (1) QLCC 28 PINS 28 PINS 71 to 83 40 to 65 24 30 C/W For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. The junction-to-ambient thermal resistance under natural convection is obtained in a simulation on a JEDEC-standard, high-K board, as specified in JESD51-7, in an environment described in JESD51-2a. The junction-to-case (top) thermal resistance is obtained by simulating a cold plate test on the package top. No specific JEDEC-standard test exists, but a close description can be found in the ANSI SEMI standard G30-88. Copyright (c) 1999-2011, Texas Instruments Incorporated UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com ABSOLUTE MAXIMUM RATINGS (1) UC2827-1 UC2827-2 UC3827-1 UC3827-2 Supply voltage, VCC 20 CEAO, CEA+, CEA-, CSAO, CSA+, CSA-, CT, DELAY, PUSH, PULL, RAMP, RT, SS, SYNC, VEA+, VEAO, Input voltage range -0.3 to 5 V+ and BUCK 90-VCC 250 mA 1 A I/O continuous 200 mA I/O peak 0.8 A I/O continuous BUCK driver I/O peak PUSH/PULL driver V 90 SRC Storage temperature -65 to 150 Junction temperature -55 to 150 Lead temperature (soldering, 10 sec) (1) UNITS C 300 Voltages are referenced to ground. Currents are positive into, negative out of the specified terminal. Consult Packaging section of databook for thermal limitations and considerations of packages. ELECTRICAL CHARACTERISTICS Unless otherwise spsecified, VVCC = 15 V, VV+ = 14.3 V, CCT = 340 pF, RRT = 10 k, RDELAY = 24.3 k, VSRC = VGND = VBUCK= VPUSH = VPULL outputs no load, TJ = TA PARAMETER TEST CONDITIONS MIN TYP MAX 8.3 8.8 9.5 0.9 1.2 UNIT SUPPLY VCC UVLO, Turn-on Hysteresis IVCC Supply current start IVCC Supply current run 1.5 V 1000 A 32 45 mA 1 2 mA VVCC = 8 V IV+ buck high 0.2 V VOLTAGE ERROR AMPLIFIER IB 0.5 VIO AVOL GBW (1) Gain bandwidth VOL Low-level output voltage IVEAO = 0 A (No load) VOH High-level output voltage IVEAO = 0 A (No load) 3 A 10 mV 80 95 dB 1 4 MHz 2.85 0.3 0.5 V 3 3.20 V -1 -5 A 5 mV CURRENT SENSE AMPLIFIER IB VIO AVOL GBW (1) Gain bandwidth VOL Low-level output voltage ICEAO = 0 A (No load) VOH High-level output voltage ICEAO = 0 A (No load) CMRR Common mode range (1) (1) 80 110 dB 15 29 MHz 0.25 3 -0.3 0.5 3.3 V V 2 V Ensured by design. Not production tested. Copyright (c) 1999-2011, Texas Instruments Incorporated 3 UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) Unless otherwise spsecified, VVCC = 15 V, VV+ = 14.3 V, CCT = 340 pF, RRT = 10 k, RDELAY = 24.3 k, VSRC = VGND = VBUCK= VPUSH = VPULL outputs no load, TJ = TA PARAMETER TEST CONDITIONS MIN TYP MAX UNIT -1 -5 A 10 mV CURRENT ERROR AMPLIFIER IB VIO AVOL GBW (2) Gain bandwidth At 100 kHz, Measure Gain VOL ICEAO = 0 A (No Load) VOH ICEAO = 0 A (No Load) CMRR 80 110 dB 2 4.5 MHz 0.25 3.3 Common mode range (2) 0.5 3.5 -0.3 V V 5 V OSCILLATOR SECTION fOSC Frequency ICT(dsch) CT discharge current 180 3.5V at CT when CT removed 220 250 5 kHz mA PWM COMPARATOR DMAX Minimum duty cycle 200 kHz DMAX Maximum duty cycle 200 kHz 0% 85% 91% 95% BUCK OUTPUT STAGE tRISE Rise time 1 nF Load (3) 40 100 ns tFALL Fall tIme 1 nF, Load 30 80 ns IBUCK = -15 mA , V+ -BUCK (4) 1.5 2.5 V VOH High-level output voltage VOL IBUCK = -150 mA, V+ -BUCK (4) IBUCK = 15 mA (5) Low-level output voltage IBUCK = 150 mA (5) 2 2.5 V 0.2 0.4 V 0.7 1.2 V PUSH/PULL OUTPUT STAGES tRISE Rise time 1 nF load 50 100 ns tFALL Fall tIme 1 nF load 35 100 ns Overlap time Nonoverlapping time (7) UCx827-1 1 nF loads (6) 100 250 400 ns UCx827-2 100 250 500 ns 2 3 V 2.5 3 V 0.2 0.8 V 0.6 1.2 V IPUSH/PULL = -10 mA, VCC - PUSH (8) VOH High-level output voltage VOL Low-level output voltage IPUSH/PULL = -100 mA, VCC - PUSH (8) IPUSH/PULL = 10 mA (8) IPUSH/PULL = 100 mA (8) REFERENCE Reference voltage ISC 4.8 5 5.2 V -35 -50 -65 mA 0.5V < VVCC < 20 V 5 20 mV 0 mA < IIO < 10 mA 8 20 mV 250 500 mV -12 -25 A Shor-circuit current VREF = 0V Line regulation Load regulation SOFT START VOL Low-level output voltage saturation ISS Soft-start current (2) (3) (4) (5) (6) (7) (8) 4 VVCC = 7 V -5 Ensured by design. Not production tested. Measure the rise time from when BUCK crosses 1 V until it crosses 9 V. To force BUCK high, force VCSAO=2.5 V, VCEAO = 2.5 V, a 25-k pulldown resistor from RAMP to ground, and VCT = 0.5 V. To force BUCK low, force VCSAO = 2.5 V, VCEAO = 2.5 V, a 10-k pulldown resistor from RAMP to ground, and VCT = 3.5 V. The overlap time is measured from the point at which the rising edge of PUSH/PULL crosses 5 V until the falling edge of PULL/PUSH crosses 5V. The non-overlap time is measured from the point at which the falling edge of PUSH/PULL crosses 5 V until the rising edge of PULL/PUSH crosses 5 V. To toggle PUSH or PULL into a desired state, pulse CT from 0.5 V to 3.5 V. PUSH and PULL toggle on the rising edge of CT. Copyright (c) 1999-2011, Texas Instruments Incorporated UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com CONNECTION DIAGRAMS PLCC-28 (Q PACKAGE) (TOP VIEW) DIL-24 (N or J, DW PACKAGES) (TOP VIEW) Q PACKAGE (TOP VIEW) 24 23 22 21 20 19 18 17 16 15 14 13 PUSH VCC PULL PGND DELAY SYNC CT RT VEA- REF VEA+ CEA- SS RAMP CEAO CSAO CSA+ CSA- VEAO 4 5 3 2 1 28 27 26 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 PGND NC NC DELAY SYNC CT RT GND CEA+ CEA- VEA+ REF NC VEA- 1 2 3 4 5 6 7 8 9 10 11 12 V+ BUCK SRC SS RAMP CEAO CSAO CSA+ CSA- VEAO GND CEA+ SRC BUCK NC V+ PUSH VCC PULL N, J OR DW PACKAGES (TOP VIEW) NC - No internal connection Terminal Functions TERMINAL I/O DESCRIPTION N or DW Q BUCK 2 3 O Output of the buck PWM controller. The BUCK output is a floating driver, optimized for controlling the gate of an N-channel MOSFET. The peak sink and source currents are 1 A. VCC undervoltage faults disables BUCK to an off condition (low). CEA+ 12 13 I Non-inverting input of the current error amplifier. CEA- 13 14 I Inverting input of the current error amplifier CEAO 6 7 O Output of the current error amplifier and the inverting input of the PWM comparator of the buck converter. CSA+ 8 9 I Noninverting input of the current sense amplifier. CSA- 9 10 I Inverting input of the current sense amplifier. CSAO 7 8 O Output of the current sense amplifier and the noninverting input of the current limit comparator. When the signal level on this pin exceeds the 3V threshold of the current limit comparator, the buck gate drive pulse is terminated. This feature is useful to implement cycle-by-cycle current limiting for the buck converter. CT 18 20 I Provides for the timing capacitor which is connected between CT and GND. The oscillator frequency is set by CT and a resistor RT, connected between pin RT and GND. The CT discharge current is approximately 40 x the bias current through the resistor connected to RT. A practical maximum value for the discharge current is 20 mA. The frequency of the oscillator is given by equation (1) DELAY 20 22 I A resistor to GND programs the overlap time of the PUSH and PULL outputs of the UC3827-1 and the dead time of the PUSH and PULL outputs of the UC3827-2. The minimum value of the resistor, RDELAY, is 18 k. The delay or overlap time is given by equation (2) GND 11 12 - Ground reference for all sensitive setup components not related to driving the outputs. They include all timing, voltage sense, current sense, and bypass components. PGND 21 25 - Ground connection for the PUSH and PULL outputs. PGND must be connected to GND at a single point on the printed circuit board. This is imperative to prevent large, high frequency switching currents flowing through the ground metalization inside the device. PULL 22 26 O Ground referenced output to drive an N-channel MOSFET. The PULL and the PUSH outputs are driving the two switches of the push-pull converter with complementary signals at close to a 50% duty cycle. Any undervoltage faults will disable PULL to an off condition (low). NAME 0.77 (Hz) RRT CCT R t DELAY + DELAY 10*9 (s) 200W f OSC + (1) (2) Copyright (c) 1999-2011, Texas Instruments Incorporated 5 UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com Terminal Functions (continued) TERMINAL NAME PUSH N or DW Q 24 28 I/O DESCRIPTION O Ground referenced output to drive an N-channel MOSFET. The PULL and the PUSH outputs are driving the two switches of the push-pull converter with complementary signals at close to a 50% duty cycle. Any undervoltage faults disables PUSH to an off condition (low). RAMP 5 6 I The RAMP voltage, after a 700 mV internal level shift, is fed to the noninverting input of the buck PWM comparator. A resistor to VIN and a capacitor to GND provide an input voltage feedforward signal for the buck controller in voltage mode control. In peak current mode control, the RAMP pin receives the current signal of the buck converter. In an average current mode setup, the RAMP pin has a linearly increasing ramp signal. This waveform may be generated either by connecting RAMP directly to CT, or by connecting both a resistor from VCC to RAMP and a capacitor from RAMP to GND. REF 15 16 O The output of the +5V on board reference. Bypass this pin with a capacitor to GND. The reference is off when the chip is in undervoltage lockout mode.o RT 17 19 I A resistor to GND programs the charge current of the timing capacitor connected to CT. The charge current approximately equals that shown in equation (3). The charge current should be less than 500 A to keep CT's discharge peak current less than 20 mA, which is CT's maximum practical discharge value. The discharge time, which sets the maximum duty cycle, is set internally and is influenced by the charge current. SRC 3 4 I The source connection for the floating buck switch. The voltage on the SRC pin can exceed VCC but must be lower than 90 V-VVCC. Also, during turn-off transients of the buck switch, the voltage at SRC can go to -2V. SS 4 5 O 5Soft-start pin requires a capacitor to GND. During soft-start the output of the voltage error amplifier is clamped to the soft-start capacitor voltage which is slowly charged by an internal current source. In UVLO, SS is held low. SYNC 19 21 I A bidirectional pin for the oscillator., used to synchronize several chips to the fastest oscillator. Its input synchronization threshold is 1.4 V. The SYNC voltage is 3.6 V when the oscillator capacitor, CT, is discharged. Otherwise it is 0 V. If the recommended synchronization circuit is not used, a 1 k or lower value resistor from SYNC to GND may be needed to increase the fall time of the signal at SYNC. VCC 23 27 I A voltage source connected to this pin supplies the power for the UC3827. It is recommended to bypass this pin to both GND and PGND ground connections with good quality high frequency capacitors VEA+ 14 15 I Non-inverting input of the voltage error amplifier VEA- 16 18 I Inverting input of the voltage error amplifier VEAO 10 11 O Output of the voltage error amplifier I Supply voltage for the buck output. The floating driver of the UC3827 uses the bootstrap technique which requires a reservoir capacitor to store the required energy for the on time of the buck switch. A diode must be connected from VCC to V+ to charge the reservoir capacitor. This diode must be able to withstand VIN. The reservoir capacitor must be connected between V+ and SRC. V+ (3) 6 1 1 I RT + 2.5 V RRT Copyright (c) 1999-2011, Texas Instruments Incorporated UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com APPLICATION INFORMATION VREF RT 2.5 V - + RT CT OSCILLATOR VREF 1.4 V 2.5 V 2.9 V CT S R SYNC 0.5 V 10 kW VDG-99086 Figure 1. Oscillator Block With External Connections CIRCUIT BLOCK DESCRIPTION PWM Oscillator The oscillator block diagram with external connections is shown in Equation 1. A resistor (RT) connected to pin RT sets the linear charge current: I RT + 2.5 V RRT (1) The timing capacitor (CCT) is linearly charged with the charge current forcing the OSC pin to charge to a 3.4 V threshold. After exceeding this threshold, the RS flip-flop is set driving CLKSYN high and RDEAD low which discharges CCT. CT continues to discharge until it reaches a 0.5 V threshold and resets the RS flip-flop which repeats the charging sequence as shown in Figure 2 As shown in Figure 3, several oscillators are synchronized to the highest free running frequency by connecting 100 pF capacitors in series with each CLKSYN pin and connecting the other side of the capacitors together forming the CLKSYN bus. The CLKSYN bus is then pulled down to ground with a resistance of approximately 10k. Referring to Figure 1, the synchronization threshold is 1.4 V. The oscillator blanks any synchronization pulse that occurs when OSC is below 2.5 V. This allows units, once they discharge below 2.5 V, to continue through the current discharge and subsequent charge cycles whether or not other units on the CLKSYN bus are still synchronizing. This requires the frequency of all free running oscillators to be within 17% of each other to assure synchronization. Copyright (c) 1999-2011, Texas Instruments Incorporated 7 UC2827-1, UC2827-2 UC3827-1, UC3827-2 SLUS365D - APRIL 1999 - REVISED APRIL 2011 www.ti.com VAO Current Command Charging Discharging OSC 2.9 V 0.5 V THRESHOLD 3.6 V 1.4 V Threshold CLKSYN 8.5 V OUT 0V VDG-99087 Figure 2. Oscillator and PWM Output Waveform OSC2 OSC3 SYNC SYNC SYNC 100 pF 100 pF 100 pF CLKSYN BUS OSC1 100 pF OSC10 SYNC 10 kW VDG-99085 Figure 3. Oscillator Synchronization Connection Diagram REVISION HISTORY REVISION 8 DATE OF CHANGE SLUS365A 8/2005 SLUS365D 4/2011 DESCRIPTION Improved CMRR of CSA from ( 0 - 2 V) to ( -0.3 - 2 V) Improved CMRR of CEA from ( 0 - 5 V) to ( -0.3 - 5 V) Updated the Thermal Information Section Copyright (c) 1999-2011, Texas Instruments Incorporated PACKAGE OPTION ADDENDUM www.ti.com 23-Jul-2010 PACKAGING INFORMATION Orderable Device (1) Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) UC2827DW-1 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC2827DW-1G4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC2827DW-2 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples UC2827DW-2G4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples UC2827DWTR-1 ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples UC2827DWTR-1G4 ACTIVE SOIC DW 24 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Purchase Samples UC2827N-1 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Purchase Samples UC2827N-1G4 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Purchase Samples UC3827DW-1 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC3827DW-1G4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC3827DW-2 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC3827DW-2G4 ACTIVE SOIC DW 24 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR Request Free Samples UC3827N-1 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Request Free Samples UC3827N-1G4 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Request Free Samples UC3827N-2 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Request Free Samples UC3827N-2G4 ACTIVE PDIP N 24 15 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Request Free Samples The marketing status values are defined as follows: Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 23-Jul-2010 ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC3827-1 : * Military: UC1827-1 NOTE: Qualified Version Definitions: * Military - QML certified for Military and Defense Applications Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device UC2827DWTR-1 Package Package Pins Type Drawing SOIC DW 24 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2000 330.0 24.4 Pack Materials-Page 1 10.85 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 15.8 2.7 12.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC2827DWTR-1 SOIC DW 24 2000 367.0 367.0 45.0 Pack Materials-Page 2 MECHANICAL DATA MPDI006B - SEPTEMBER 2001 - REVISED APRIL 2002 N (R-PDIP-T24) PLASTIC DUAL-IN-LINE 1.222 (31,04) MAX 24 13 0.360 (9,14) MAX 1 12 0.070 (1,78) MAX 0.200 (5,08) MAX 0.425 (10,80) MAX 0.020 (0,51) MIN Seating Plane 0.125 (3,18) MIN 0.100 (2,54) 0'-15' 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) 0.010 (0,25) NOM 4040051-3/D 09/01 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-010 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated