5V/3.3V 1:5 CLOCK DISTRIBUTION Precision EdgeTM SY100EL14V FEATURES 3.3V and 5V power supply options Typical 30ps output-to-output skew Max. 50ps output-to-output skew Synchronous enable/disable Multiplexed clock input 75K internal input pull-down resistors Available in 20-pin SOIC package Precision EdgeTM DESCRIPTION The SY100EL14V is a low skew 1:5 clock distribution chip designed explicitly for low skew clock distribution applications. The device can be driven by either a differential or single-ended ECL or, if positive power supplies are used, PECL input signal. The EL14V is suitable for operation in systems operating from 3.3V to 5.0V supplies. If a single-ended input is to be used the VBB output should be connected to the CLK input and bypassed to ground via a 0.01F capacitor. The VBB output is designed to act as the switching reference for the input of the EL14V under single-ended input conditions, as a result this pin can only source/sink up to 0.5mA of current. The EL14V features a multiplexed clock input to allow for the distribution of a lower speed scan or test clock along with the high speed system clock. When LOW (or left open and pulled LOW by the input pull-down resistor) the SEL pin will select the differential clock input. The common enable (EN) is synchronous so that the outputs will only be enabled/disabled when they are already in the LOW state. This avoids any chance of generating a runt clock pulse when the device is enabled/ disabled as can happen with an asynchronous control. The internal flip flop is clocked on the falling edge of the input clock, therefore all associated specification limits are referenced to the negative edge of the clock input. When both differential inputs are left open, CLK input will pull down to VEE and CLK input will bias around VCC/2. PIN CONFIGURATION/BLOCK DIAGRAM VCC EN VCC NC SCLK CLK CLK VBB SEL VEE 20 19 18 17 16 15 14 13 12 11 D Q 1 Q0 2 Q0 1 3 Q1 4 Q1 5 Q2 0 6 Q2 7 Q3 8 Q3 9 Q4 10 Q4 SOIC TOP VIEW PIN NAMES Pin TRUTH TABLE CLK SCLK EN Q CLK Differential Clock Inputs Function L X SEL L L L SCLK Scan Clock Input H X L L H EN Synchronous Enable X L H L L SEL Clock Select Input X H H L H VBB Reference Output X X X H L* Q0-4 Differential Clock Outputs * On next negative transition of CLK or SCLK Precision Edge is a trademark of Micrel, Inc. Rev.: C 1 Amendment: /0 Issue Date: September 2004 Precision EdgeTM SY100EL14V Micrel ABSOLUTE MAXIMUM RATINGS(1) Symbol VEE VIN (3) IOUT TA VEE Rating Value Unit Power Supply (VCC = 0V) -8.0 to 0 VDC Input Voltage (VCC = 0V) 0 to -6.0 VDC Output Current -Continuous -Surge 50 100 mA -40 to +85 C -5.7 to -3.0 V Operating Temperature Range Operating Range(1),(2) Notes: 1. Absolute maximum rating, beyond which, device life may be impaired, unless otherwise specified on an individual data sheet. 2. Parametric values specified at: 100EL14V Series: -3.0V to -5.5V. 3. In PECL mode operation, VIN (max) = VCC. DC ELECTRICAL CHARACTERISTICS VEE = VEE (Min) to VEE (Max); VCC = GND(1) TA = -40C Symbol Parameter Min. TA = 0C TA = +25C TA = +85C Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -880 -1025 -955 -880 -1025 -955 -880 -1025 -955 VOH Output HIGH Voltage(2) -1085 -1005 -880 mV VOL Output LOW Voltage(2) -1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 -1810 -1705 -1620 mV VOHA Output HIGH Voltage(2) -1095 -- -- -1035 -- -- -1035 -- -- -1035 -- -- mV VOLA Output LOW Voltage(2) -- -- -1555 -- -- -1610 -- -- -1610 -- -- -1610 mV VIH Input HIGH Voltage -1165 -- -880 -1165 -- -880 -1165 -- -880 -1165 -- -880 mV VIL Input LOW Voltage -1810 -- -1475 -1810 -- -1475 -1810 -- -1475 -1810 -- -1475 mV 0.5 -300 -- -- -- -- 0.5 -300 -- -- -- -- A IIL Input LOW Current(3) CLK -- -- -- -- 0.5 -300 -- -- -- -- 0.5 -300 IIH Input High Current -- -- 150 -- -- 150 -- -- 150 -- -- 150 A IEE Power Supply Current -- 32 40 -- 32 40 -- 32 40 -- 34 42 mA VBB Output Reference Voltage -1.38 -- -1.26 -1.38 -- -1.26 -1.38 -- -1.26 -1.38 -- -1.26 V Notes: 1. This table replaces the three traditionally seen in ECL 100K data books. The same DC parameter values at VEE = -4.5V now apply across the full VEE range of -3.0V to -5.5V. Outputs are terminated through a 50 resistor to -2.0V except where otherwise specified on the individual data sheets. 2. VIN = VIH(Max) or VIL(Min). 3. VIN = VIL(Max). M9999-090704 hbwhelp@micrel.com or (408) 955-1690 2 Precision EdgeTM SY100EL14V Micrel AC ELECTRICAL CHARACTERISTICS VEE = VEE (Min) to VEE (Max); VCC = GND TA = -40C Symbol Parameter TA = 0C TA = +25C TA = +85C Min. Max. Min. Max. Min. Typ. Max. Min. Max. Unit 520 470 470 720 770 770 550 500 500 750 800 800 580 530 530 680 680 680 780 830 830 630 580 580 830 880 880 -- -- 200 50 -- -- 200 50 -- -- -- -- 200 50 -- -- 200 50 ps tPLH tPHL Propagation Delay CLK to Q (Diff) CLK to Q (SE) SCLK to Q ps tskew Part-to-Part Skew(1) Within-Device Skew tS Setup Time EN 150 -- 150 -- 150 -- -- 150 -- ps tH Hold Time EN 200 -- 200 -- 200 -- -- 200 -- ps VPP Minimum Input Swing 150 -- 150 -- 150 -- -- 150 -- mV VCMR Common Mode Range(2) CLK VPP < 500mV VPP 500mV tr tf Output Rise/Fall Times Q (20% - 80%) mV -2.0 -1.8 -0.4 -0.4 -2.1 -1.9 -0.4 -0.4 -2.1 -1.9 -- -- -0.4 -0.4 -2.1 -1.9 -0.4 -0.4 230 500 230 500 230 360 500 230 500 ps Notes: 1. Skews are specified for identical LOW-to-HIGH or HIGH-to-LOW transitions. 2. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPP(Min) and 1V. The lower end of the VCMR range varies 1:1 with VEE. The numbers in the specification table assume a nominal VEE = -3.3V. For PECL operation, the VCMR(Min) will be fixed at 3.3V - |VCMR(Min)|. PRODUCT ORDERING CODE Ordering Code SY100EL14VZC SY100EL14VZCTR(2) Package Type Operating Range Marking Code Ordering Code Z20-1 Commercial XEL14V XEL14V Z20-1 Commercial Notes: 1. Recommended for new designs. 2. Tape and Reel. 3. Pb-Free (lead-free). M9999-090704 hbwhelp@micrel.com or (408) 955-1690 3 Package Type Operating Range Marking Code SY100EL14VZI(1) Z20-1 Industrial XEL14V SY100EL14VZITR(1,2) Z20-1 Industrial XEL14V SY100EL14VZY(3) Z20-1 Industrial XEL14V SY100EL14VZYTR(1,2,3) Z20-1 Industrial XEL14V Precision EdgeTM SY100EL14V Micrel 20 LEAD SOIC .300" WIDE (Z20-1) Rev. 03 MICREL, INC. TEL 1849 FORTUNE DRIVE SAN JOSE, CA 95131 + 1 (408) 944-0800 FAX + 1 (408) 944-0970 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2003 Micrel, Incorporated. M9999-090704 hbwhelp@micrel.com or (408) 955-1690 4