© Freescale Semiconductor, Inc., 2004. All rights reserved.

Freescale Semiconductor

Quick Start Guide Rev. 0.2, 10/03/2004

Quick Start Guide

Introduction and Default Settings

This kit contains everything you need to get started minus the power supply. This guide will walk you

though how to connect the board to your PC, run the pre-programmed LED test, install the correct version

of CodeWarrior Development Studio, and load an ATD (Analog to Digital) test program. Source code for

Figure 1. DEMO908AP64 Default Settings

Connect the DEMO908AP64 to your computer and apply power

1. Connect the 9-pin serial cable provided to the COM1 port of the EVB board. Connect the other end

to a COM port on your host PC.

2. There are two ways to apply power to the demo board: via the power terminal block or the J1

MCU_PORT. Refer to the DEMO908AP64 User’s Guide about using the MCU_PORT. Otherwise,

connect the +9 VDC supply into the screw-type terminal block. Please review the diagram above

for wire placement. Apply power to the power and the +5V LED should turn on. If the LED is not

on, please check the PWR_SEL jumpers and the placement of the +9 VDC power supply wires.

DEMO908AP64, Rev. 0.2

1. Press SW1 and LED1 will turn on. Release SW1 and LED1 should turn off.

2. Press SW2 and LED2 will turn on. Release SW2 and LED2 should turn off.

Install CodeWarrior Development Studio Version 3.0 for HC(S)08

If you do not have version 3.0 of CodeWarrior for HC(S)08 Special Edition installed on your computer,

please refer to the provided “CodeWarrior Development Studio for Motorola” CD for HC(S)08 Special

a license key to use CodeWarrior. You must also obtain another special edition license key, which will

allow you to experience all the features of the CodeWarrior debugger (see install, register, and license

key instructions in the CodeWarrior Quick Start). After CodeWarrior Development Studio is installed,

2. If you have not already done so, connect serial cable and apply power to the board.

3. In the working folder on the desktop, double click on the “DEMO908AP64.mcp” project file. The

CodeWarrior IDE will launch.

4. Open “DEMO908AP64_ATD.c” in the source folder by double clicking on

5. Please change the jumpers on the board to ensure proper communication between the PC and

DEMO908AP64 board.

Figure 2. MON08 Debug Setting for Serial Connection

DEMO908AP64, Rev. 0.2

7. Click the “Contact target with these settings…” button and follow the instructions on the screen.

When the “Erase and Program Flash?” window appears, click the “Yes” button.

8. To cycle the power, you should remove the VR1 jumper (PWR_SEL port) and reinstall the VR1

jumper (PWR_SEL). This action has turned the MCU supply power off and on. The +5V LED will

stay on during this power cycle. Click “OK” in the “Power Cycle Dialog” window.

9. The “CPROG08SZ Programmer” window should close after the MCU Flash is programmed. You

are now ready to run the DEMO908AP64_ATD code. Click on the green arrow in the toolbar at the

top of the screen to run the program. Once you click this button, a message in the command

• Reinstall the jumpers to the default position. Refer to Figure 1.

Unable to program the part

• Make sure the jumpers are in the debug position. Refer to Figure 2.

• Make sure the COM port matches the serial port in “Attempting to contact target and pass

security…” window.

Unable to compile the DEMO908AP64_ATD.c due to “ERROR: C1815: ADRL0 (or ADR0L) not

• Check your version of CodeWarrior by clicking on Help -> About Metrowerks CodeWarrior

– If you are using v3.1, please change all references in DEMO908AP64_ATD.c to "ADRL0" to