ADIS16407/PCBZ - Analog Devices Inc.

Sensor

PC-USB Evaluation System

Preliminary Technical Data

ADISUSBZ

Rev. PrA

Information furnished by Analog Devices is believed to be accurate and reliable.

However, no responsibility is assumed by Analog Devices for its use, nor for any

infringements of patents or other rights of third parties that may result from its use.

Specifications subject to change without notice. No license is granted by implication

or otherwise under any patent or patent rights of Analog Devices. Trademarks and

registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700 www.analog.com

GENERAL DESCRIPTION

The ADISUSB is a PC-USB evaluation system that enables basic

demonstration of many SPI-output iSensor® products (sold

separately). It provides 2mm screw holes for simple attachment

of all iSensor® products listed in Table 2, along with all

necessary cabling for connecting these devices to the USB port.

This system provides sensor data on-demand, through the USB,

at read rates up to 900SPS. Since the USB ports are serviced by

their PC’s interrupt structure, sampling in this system in not

perfectly coherent. However, in most PCs, the sample

coherence is sufficient for most datasheet parametric

verification, including in-run bias stability. This system will

run on MS Windows® XP, NT, and 2000.

Table 1. Kit Contents

ADISUSBZ PCB

A-to-B USB Cable, 6 feet

2mm stainless steel screws

12-pin, 2mm ribbon cable (ADIS16xxx/PCBZ)

iSensor® Documentation CD

GETTING STARTED QUICKLY

Step #1 - Download software to PC

Go to www.analog.com/isensor-evaluation, click on “Evaluation

Software Downloads,” click on the appropriate software

package, and follow the prompts to save it to a temporary

location on the local PC. The iSensor® Documentation CD

provides software packages as well, but the iSensor Evaluation

Tool web site provides the latest versions of each software

package.

Step #2 - Install evaluation software package

Unzip the installation package to a temporary location, and

then double-click on setup.exe, and follow the prompts. When

asked to replace system files, click “No,” and the evaluation

software will still work fine. Refer to Figure 1, Figure 2, and

Figure 3 for windows that will appear during this step.

Step #3 - Install giveio.exe driver

The giveio.exe driver is located in the software’s new directory,

which is normally under a subdirectory called “Analog Devices

iSensor®,” located in the Program Files folder. Double-click on

the file, giveio.exe, and follow the prompts to install this driver.

Refer to Figure 4, Figure 5, and Figure 6 for windows that will

appear during this Step.

Step #4 - Install USB driver

Connect the A-to-B USB cable to the PC, and then to the

ADISUSBZ PCB. The USB driver installation screen will

automatically appear on the screen in a few seconds. Follow the

prompts to install this driver. On some machines, the driver

installation screen will appear again, after clicking on “Finish.”

In this case, follow the prompts and complete the process. Refer

to Figure 7 and Figure 8 for the windows that will appear during

this step. Once complete, disconnect the cable from the

ADISUSBZ.

Step #5 - Connect ADIS16xxx/PCB to USB Interface PCB

Use the provided 2mm machine screws to secure the product

under test. Refer to Figure 9 through Figure 12 for alignment

assistance. The ADIS16xxx/PVBZ parts also require the 12-pin

ribbon cable installation displayed in these figures.

Table 2. JP1 Power Supply Settings

+3.3V +5V

ADIS16003/PCBZ

ADIS16006/PCBZ

ADIS16201/PCBZ

ADIS16203/PCBZ

ADIS16204/PCBZ

ADIS16209/PCBZ

ADIS16003/PCBZ

ADIS16006/PCBZ

ADIS16080/PCBZ

ADIS16100/PCB

ADIS16250/PCBZ

ADIS16251/PCBZ

ADIS16255/PCBZ

ADIS16300AMLZ

ADIS16350AMLZ

ADIS16354AMLZ

ADIS16355AMLZ

ADIS16365AMLZ

Note: If a product is listed twice, it can be run at +3.3 or +5V.

Step #6 - Launch evaluation software

Hook the ADISUSBZ to the USB cable and then launch the

evaluation software by double clicking on its *.exe file. The

program will also be in the Start Programs menu in Windows.

Figure 15 though Figure 21 offers some basic insights into the

operation of each product’s evaluation software. Note to

European users: some software is sensitive to the decimal

notation. If large or unreasonable numbers are observed,

change the PC’s regional setting to USA. Software packages are

being updated to fix this, but were not complete at the time of

this document’s release.

ORDERING GUIDE

Model Package Description

ADISUSBZ iSensor™ PC-USB Evaluation System

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 2 of 15

Figure 1. Installation Welcome Screen (Click OK)

Figure 2. Installation Launch Screen (click on computer button)

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 3 of 15

Figure 3. Program Group Menu (Click Continue)

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 4 of 15

Figure 4. Giveio.exe Installation Screen (Click Install)

Figure 5. Giveio.exe License Agreement (Click I Agree)

Figure 6. Giveio.exe Installation Confirmation Menu (Click Yes)

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 5 of 15

Figure 7. USB Driver Installation (Click Next)

Figure 8 .USB Driver Hardware Installation (Click on Continue Anyway)

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 6 of 15

Figure 9. Installing the ADIS16xxx/PCBZ onto the ADISUSBZ

Figure 10. ADIS16xxx/PCBZ Installed View

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 7 of 15

Figure 11. Installing ADIS1635xAMLZ onto the ADISUSBZ

Figure 12. ADIS1635xAMLZ Installed View

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 8 of 15

Figure 13 – iSensor® ADISUSBZ Interface Board Layout (Top View)

Figure 14 – iSensor® ADISUSBZ Interface Board Layout (Bottom View)

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 9 of 15

FIGURE FLAG NOTES:

1. Set the Device type to ADIS16003 or ADIS16006. Set the Interface to parallel and set the port address per ReadMeFirst.PDF

2. Set the axis being tested. Test function exercises a self-test during a single sweep on the screen.

3. Plot and log data to files.

4. Set up data logging parameters.

5. Right click over Y-Axis to adjust scale and offset of the plot.

Figure 15. ADIS16003 and ADIS16006 Evaluation Software

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 10 of 15

FIGURE FLAG NOTES:

1. Set the Device type to ADIS16080 or ADIS16100. Set the Interface to parallel and set the port address per ReadMeFirst.PDF

2. Set the output channel being tested. Test function exercises a self-test during a single sweep on the screen.

3. Plot and log data to files.

4. Set up data logging parameters.

5. Right click over Y-Axis to adjust scale and offset of the plot.

Figure 16. ADIS16080 and ADIS16100 Evaluation Software

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 11 of 15

FIGURE FLAG NOTES:

1. Perform a single read of the ADIS16201’s output data

2. Start and stop continuous reading of the ADIS16201’s output data. Set the acquisition loop delay time. This provides rough

control over sample times. Please note that this data will not have a high degree of coherence.

3. Select the file data logging option.

4. Configure the ADIS16201’s internal sample rate and filter response.

Figure 17. ADIS16201 Evaluation Software

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 12 of 15

FIGURE FLAG NOTES:

1. Perform a single read of the ADIS16203’s output data

2. Start and stop continuous reading of the ADIS16203’s output data. Set the acquisition loop delay time. This provides rough

control over sample times. Please note that this data will not have a high degree of coherence.

3. Select the file data logging option.

4. Configure the ADIS16203’s internal sample rate and filter response.

5. Graphical orientation. Note that for incline angle - 0°, the corner dot would be in the lower, left hand corner.

6. Alarm monitoring. Note that these turn red on alarm condition. They maintain their status until the Reset button is pressed,

even if the error condition has cleared.

Figure 18. ADIS16203 Evaluation Software

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 13 of 15

FIGURE FLAG NOTES:

1. Perform a single read of the ADIS16209’s output data

2. XINCL_OUT and YINCL_OUT are horizontal incline outputs. ROTATION is the vertical-oriented rotational position

measurement. This requires the X and Y axes to be in the vertical plane, with respect to the earth’s surface.

3. This graph displays the vertical oriented, rotational position. This requires the X and Y axes to be in the vertical plane, with

respect to the earth’s surface.

4. Start and stop continuous reading of the ADIS16209’s output data. The acquisition loop time provides rough control over

sample times. Please note that this data will not have a high degree of coherence.

5. The acquisition loop time provides rough control over sample times. Please note that this data will not have a high degree of

coherence.

6. Configure the ADIS16209’s internal sample rate and filter response.

Figure 19. ADIS16209 Evaluation Software

ADISUSBZ Preliminary Technical Data

Rev. PrA | Page 14 of 15

FIGURE FLAG NOTES:

1. Perform a single read of the ADIS1625x’s output data

2. Start and stop continuous reading of the ADIS1625x’s output data. Set the acquisition loop delay time. This provides rough

control over sample times. Please note that this data will not have a high degree of coherence.

3. Select the file data logging option.

4. Configure the ADIS1625x’s internal sample rate and filter response.

5. Set the measurement range from the three options available in the ADIS1625x.

6. Exercise the user calibration functions.

NOTE: The ADIS16255 can use this software. The ADIS16251 can use this software, but the rate output measured with be 4 times greater

than the actual angular rate.

Figure 20. ADIS1625x Evaluation Software

Preliminary Technical Data ADISEVAL/USBZ

Rev. PrA | Page 15 of 15 EB07693-0-7/08(PrA)

4 3

Figure 21. ADIS1635x Evaluation Software

FIGURE FLAG NOTES:

1. Perform a single read of the ADIS1635x’s output data. Also select “Loop” checkbox for continuous data scroll across the screen.

Use the Loop delay box to add delay between each sample displayed to the screen.

2. Select individual sensor outputs for display.

3. Use Configuration menu to access sample rate, filtering, calibration, I/O control and all other internal configuration controls for

the ADIS1635x products.

4. Use Device option to select which part to evaluate.