LM4766 LM4766 Overture Audio Power Amplifier Series Dual 40W Audio Power Amplifier with Mute Literature Number: SNAS031E LM4766 OvertureTM Audio Power Amplifier Series Dual 40W Audio Power Amplifier with Mute General Description Key Specifications The LM4766 is a stereo audio amplifier capable of delivering typically 40W per channel with the non-isolated "T" package and 30W per channel with the isolated "TF" package of continuous average output power into an 8 load with less than 0.1% (THD+N). The performance of the LM4766, utilizing its Self Peak Instantaneous Temperature (Ke) (SPiKeTM) Protection Circuitry, places it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe Protection means that these parts are safeguarded at the output against overvoltage, undervoltage, overloads, including thermal runaway and instantaneous temperature peaks. Each amplifier within the LM4766 has an independent smooth transition fade-in/out mute that minimizes output pops. The IC's extremely low noise floor at 2V and its extremely low THD+N value of 0.06% at the rated power make the LM4766 optimum for high-end stereo TVs or minicomponent systems. j THD+N at 1kHz at 2 x 30W continuous average output power into 8 0.1% (max) j THD+N at 1kHz at continuous average output power of 2 x 30W into 8 0.009% (typ) Features n n n n n SPiKe Protection Minimal amount of external components necessary Quiet fade-in/out mute mode Non-Isolated 15-lead TO-220 package Wide Supply Range 20V - 78V Applications n High-end stereo TVs n Component stereo n Compact stereo Connection Diagram Plastic Package 10092802 Top View Non-Isolated TO-220 Package Order Number LM4766T See NS Package Number TA15A Isolated TO-220 Package Order Number LM4766TF See NS Package Number TF15B SPiKeTM Protection and OvertureTM are trademarks of National Semiconductor Corporation. (c) 2006 National Semiconductor Corporation DS100928 www.national.com LM4766 OvertureTM Audio Power Amplifier Series Dual 40W Audio Power Amplifier with Mute March 2006 LM4766 Typical Application 10092801 FIGURE 1. Typical Audio Amplifier Application Circuit Note: Numbers in parentheses represent pinout for amplifier B. *Optional component dependent upon specific design requirements. www.national.com 2 Junction Temperature (Note 8) (Notes 4, 150C Thermal Resistance 5) Non-Isolated T-Package If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. JC JC Supply Voltage |VCC| + |VEE| (No Input) 78V (with Input) T and TF Packages 74V Output Current 260C Storage Temperature -40C to +150C (VCC or VEE) and |VCC| + |VEE| 60V Differential Input Voltage 2C/W Soldering Information Supply Voltage |VCC| + |VEE| Common Mode Input Voltage 1C/W Isolated TF-Package Operating Ratings (Notes 4, 5) Temperature Range 60V TMIN TA TMAX Internally Limited Power Dissipation (Note 6) 62.5W ESD Susceptability (Note 7) 3000V -20C TA +85C Supply Voltage |VCC| + |VEE| (Note 1) 20V to 60V Electrical Characteristics (Notes 4, 5) The following specifications apply for VCC = +30V, VEE = -30V, IMUTE = -0.5mA with RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter |VCC| + Power Supply Voltage |VEE| (Note 11) PO Output Power Conditions GND - VEE 9V LM4766 Units (Limits) Typical Limit (Note 9) (Note 10) 18 20 V (min) 60 V (max) T Package, VCC = 30V, THD+N = 0.1% (max), f = 1kHz, f = 20kHz 40 30 W/ch (min) TF Package, VCC = 26V(Note 13), THD+N = 0.1% (max), 30 25 W/ch (min) (Notes 3, 13) (Continuous Average) f = 1kHz, f = 20kHz THD+N Total Harmonic Distortion Plus Noise T Package 30W/ch, RL = 8, 20Hz f 20kHz, AV = 26dB 0.06 % TF Package 25W/ch, RL = 8, 20Hz f 20kHz, AV = 26dB 0.06 % Xtalk Channel Separation f = 1kHz, VO = 10.9Vrms 60 SR (Note 3) Slew Rate VIN = 1.2Vrms, trise = 2ns 9 5 V/s (min) dB 48 100 mA (max) Itotal Total Quiescent Power Both Amplifiers VCM = 0V, (Note 2) Supply Current VO = 0V, IO = 0mA VOS (Note 2) Input Offset Voltage VCM = 0V, IO = 0mA 1 10 mV (max) IB Input Bias Current VCM = 0V, IO = 0mA 0.2 1 A (max) IOS Input Offset Current VCM = 0V, IO = 0mA 0.01 0.2 A (max) IO Output Current Limit |VCC| = |VEE| = 10V, tON = 10ms, 4 3 Apk (min) VO = 0V VOD Output Dropout Voltage |VCC-VO|, VCC = 20V, IO = +100mA 1.5 4 V (max) (Note 2) (Note 12) |VO-VEE|, VEE = -20V, IO = -100mA 2.5 4 V (max) 3 www.national.com LM4766 Absolute Maximum Ratings LM4766 Electrical Characteristics (Notes 4, 5) (Continued) The following specifications apply for VCC = +30V, VEE = -30V, IMUTE = -0.5mA with RL = 8 unless otherwise specified. Limits apply for TA = 25C. Symbol PSRR Parameter Power Supply Rejection Ratio (Note 2) Conditions VCC = 30V to 10V, VEE = -30V, LM4766 Units (Limits) Typical Limit (Note 9) (Note 10) 125 85 dB (min) 110 85 dB (min) 110 75 dB (min) 115 80 dB (min) 8 2 MHz (min) 2.0 8 V (max) VCM = 0V, IO = 0mA VCC = 30V, VEE = -30V to -10V VCM = 0V, IO = 0mA CMRR Common Mode Rejection Ratio VCC = 50V to 10V, VEE = -10V to -50V, (Note 2) VCM = 20V to -20V, IO = 0mA AVOL (Note 2) Open Loop Voltage Gain RL = 2k, VO = 40V GBWP Gain Bandwidth Product fO = 100kHz, VIN = 50mVrms eIN (Note 3) Input Noise IHF-A Weighting Filter RIN = 600 (Input Referred) PO = 1W, A-Weighted, SNR Signal-to-Noise Ratio 98 dB 112 dB Measured at 1kHz, RS = 25 PO = 25W, A-Weighted Measured at 1kHz, RS = 25 AM Mute Attenuation Pin 6,11 at 2.5V 115 80 dB (min) Note 1: Operation is guaranteed up to 60V, however, distortion may be introduced from SPiKe Protection Circuitry if proper thermal considerations are not taken into account. Refer to the Application Information section for a complete explanation. Note 2: DC Electrical Test; Refer to Test Circuit #1. Note 3: AC Electrical Test; Refer to Test Circuit #2. Note 4: All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Note 5: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 6: For operating at case temperatures above 25C, the device must be derated based on a 150C maximum junction temperature and a thermal resistance of JC = 1C/W (junction to case) for the T package. Refer to the section Determining the Correct Heat Sink in the Application Information section. Note 7: Human body model, 100pF discharged through a 1.5k resistor. Note 8: The operating junction temperature maximum is 150C, however, the instantaneous Safe Operating Area temperature is 250C. Note 9: Typicals are measured at 25C and represent the parametric norm. Note 10: Limits are guarantees that all parts are tested in production to meet the stated values. Note 11: VEE must have at least -9V at its pin with reference to ground in order for the under-voltage protection circuitry to be disabled. In addition, the voltage differential between VCC and VEE must be greater than 14V. Note 12: The output dropout voltage, VOD, is the supply voltage minus the clipping voltage. Refer to the Clipping Voltage vs. Supply Voltage graph in the Typical Performance Characteristics section. Note 13: When using the isolated package (TF), the JC is 2C/W verses 1C/W for the non-isolated package (T). This increased thermal resistance from junction to case requires a lower supply voltage for decreased power dissipation within the package. Voltages higher than 26V maybe used but will require a heat sink with less than 1C/W thermal resistance to avoid activating thermal shutdown during normal operation. www.national.com 4 LM4766 Test Circuit #1 (Note 2) (DC Electrical Test Circuit) 10092803 Test Circuit #2 (Note 3) (AC Electrical Test Circuit) 10092804 5 www.national.com LM4766 Bridged Amplifier Application Circuit 10092805 FIGURE 2. Bridged Amplifier Application Circuit www.national.com 6 LM4766 Single Supply Application Circuit 10092806 FIGURE 3. Single Supply Amplifier Application Circuit Note: *Optional components dependent upon specific design requirements. Auxiliary Amplifier Application Circuit 10092807 FIGURE 4. Special Audio Amplifier Application Circuit 7 www.national.com LM4766 Equivalent Schematic (excluding active protection circuitry) LM4766 (One Channel Only) 10092808 www.national.com 8 LM4766 External Components Description Components 1 Functional Description RB Prevents currents from entering the amplifier's non-inverting input which may be passed through to the load upon power down of the system due to the low input impedance of the circuitry when the undervoltage circuitry is off. This phenomenon occurs when the supply voltages are below 1.5V. Inverting input resistance to provide AC gain in conjunction with Rf. 2 Ri 3 Rf Feedback resistance to provide AC gain in conjunction with Ri. 4 Ci (Note 14) Feedback capacitor which ensures unity gain at DC. Also creates a highpass filter with Ri at fC = 1/(2RiCi). 5 CS Provides power supply filtering and bypassing. Refer to the Supply Bypassing application section for proper placement and selection of bypass capacitors. 6 RV (Note 14) Acts as a volume control by setting the input voltage level. 7 RIN (Note 14) Sets the amplifier's input terminals DC bias point when CIN is present in the circuit. Also works with CIN to create a highpass filter at fC = 1/(2RINCIN). Refer to Figure 4. 8 CIN (Note 14) Input capacitor which blocks the input signal's DC offsets from being passed onto the amplifier's inputs. 9 RSN (Note 14) Works with CSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. 10 CSN (Note 14) Works with RSN to stabilize the output stage by creating a pole that reduces high frequency instabilities. The pole is set at fC = 1/(2RSNCSN). Refer to Figure 4. 11 L (Note 14) 12 R (Note 14) Provides high impedance at high frequencies so that R may decouple a highly capacitive load and reduce the Q of the series resonant circuit. Also provides a low impedance at low frequencies to short out R and pass audio signals to the load. Refer to Figure 4. Provides DC voltage biasing for the transistor Q1 in single supply operation. 13 RA 14 CA Provides bias filtering for single supply operation. 15 RINP (Note 14) Limits the voltage difference between the amplifier's inputs for single supply operation. Refer to the Clicks and Pops application section for a more detailed explanation of the function of RINP. 16 RBI Provides input bias current for single supply operation. Refer to the Clicks and Pops application section for a more detailed explanation of the function of RBI. 17 RE Establishes a fixed DC current for the transistor Q1 in single supply operation. This resistor stabilizes the half-supply point along with CA. 18 RM Mute resistance set up to allow 0.5mA to be drawn from pin 6 or 11 to turn the muting function off. RM is calculated using: RM (|VEE| - 2.6V)/l where l 0.5mA. Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section. 19 CM Mute capacitance set up to create a large time constant for turn-on and turn-off muting. 20 S1 Mute switch that mutes the music going into the amplifier when opened. Note 14: Optional components dependent upon specific design requirements. 9 www.national.com LM4766 Typical Performance Characteristics THD+N vs Frequency THD+N vs Frequency 10092855 10092856 THD+N vs Output Power THD+N vs Output Power 10092858 10092857 THD+N vs Distribution THD+N vs Distribution 10092872 www.national.com 10092873 10 LM4766 Typical Performance Characteristics (Continued) Channel Separation vs Frequency Clipping Voltage vs Supply Voltage 10092868 10092810 Output Power vs Load Resustance Output Power vs Supply Voltage 10092878 10092874 Power Dissipation vs Output Power Power Dissipation vs Output Power 10092876 10092877 11 www.national.com LM4766 Typical Performance Characteristics (Continued) Max Heatsink Thermal Resistance (C/W) at the Specified Ambient Temperature (C) 10092875 Note: The maximum heatsink thermal resistance values, SA, in the table above were calculated using a CS = 0.2C/W due to thermal compound. SPiKe Protection Response Safe Area 10092860 10092859 Pulse Power Limit Pulse Power Limit 10092863 www.national.com 10092864 12 LM4766 Typical Performance Characteristics (Continued) Pulse Response Large Signal Response 10092866 10092887 Power Supply Rejection Ratio Common-Mode Rejection Ratio 10092888 10092889 Open Loop Frequency Response Supply Current vs Case Temperature 10092890 10092865 13 www.national.com LM4766 Typical Performance Characteristics (Continued) Input Bias Current vs Case Temperature Mute Attenuation vs Mute Current (per Amplifier) 10092867 10092885 Output Power/Channel vs Supply Voltage f = 1kHz, RL = 4, 80kHz BW Mute Attenuation vs Mute Current (per Amplifier) 10092886 10092891 Output Power/Channel vs Supply Voltage f = 1kHz, RL = 8, 80kHz BW Output Power/Channel vs Supply Voltage f = 1kHz, RL = 6, 80kHz BW 10092892 www.national.com 10092893 14 MUTE MODE The muting function of the LM4766 allows the user to mute the music going into the amplifier by drawing more than 0.5mA out of each mute pin on the device. This is accomplished as shown in the Typical Application Circuit where the resistor RM is chosen with reference to your negative supply voltage and is used in conjunction with a switch. The switch when opened cuts off the current flow from pin 6 or 11 to -VEE, thus placing the LM4766 into mute mode. Refer to the Mute Attenuation vs Mute Current curves in the Typical Performance Characteristics section for values of attenuation per current out of pins 6 or 11. The resistance RM is calculated by the following equation: RM (|-VEE| - 2.6V)/Ipin6 where Ipin6 = Ipin11 0.5mA. DETERMlNlNG MAXIMUM POWER DISSIPATION Power dissipation within the integrated circuit package is a very important parameter requiring a thorough understanding if optimum power output is to be obtained. An incorrect maximum power dissipation calculation may result in inadequate heat sinking causing thermal shutdown and thus limiting the output power. Equation (1) exemplifies the theoretical maximum power dissipation point of each amplifier where VCC is the total supply voltage. (1) PDMAX = VCC2/22RL Thus by knowing the total supply voltage and rated output load, the maximum power dissipation point can be calculated. The package dissipation is twice the number which results from Equation (1) since there are two amplifiers in each LM4766. Refer to the graphs of Power Dissipation versus Output Power in the Typical Performance Characteristics section which show the actual full range of power dissipation not just the maximum theoretical point that results from Equation (1). Both pins 6 and 11 can be tied together so that only one resistor and capacitor are required for the mute function. The mute resistance must be chosen such that greater than 1mA is pulled through the resistor RM so that each amplifier is fully pulled out of mute mode. Taking into account supply line fluctuations, it is a good idea to pull out 1mA per mute pin or 2 mA total if both pins are tied together. UNDER-VOLTAGE PROTECTION Upon system power-up, the under-voltage protection circuitry allows the power supplies and their corresponding capacitors to come up close to their full values before turning on the LM4766 such that no DC output spikes occur. Upon turn-off, the output of the LM4766 is brought to ground before the power supplies such that no transients occur at power-down. DETERMINING THE CORRECT HEAT SINK The choice of a heat sink for a high-power audio amplifier is made entirely to keep the die temperature at a level such that the thermal protection circuitry does not operate under normal circumstances. OVER-VOLTAGE PROTECTION The LM4766 contains over-voltage protection circuitry that limits the output current to approximately 4.0APK while also providing voltage clamping, though not through internal clamping diodes. The clamping effect is quite the same, however, the output transistors are designed to work alternately by sinking large current spikes. The thermal resistance from the die (junction) to the outside air (ambient) is a combination of three thermal resistances, JC, CS, and SA. In addition, the thermal resistance, JC (junction to case), of the LM4766T is 1C/W. Using Thermalloy Thermacote thermal compound, the thermal resistance, CS (case to sink), is about 0.2C/W. Since convection heat flow (power dissipation) is analogous to current flow, thermal resistance is analogous to electrical resistance, and temperature drops are analogous to voltage drops, the power dissipation out of the LM4766 is equal to the following: (2) PDMAX = (TJMAX-TAMB)/JA where TJMAX = 150C, TAMB is the system ambient temperature and JA = JC + CS + SA. SPiKe PROTECTION The LM4766 is protected from instantaneous peaktemperature stressing of the power transistor array. The Safe Operating graph in the Typical Performance Characteristics section shows the area of device operation where SPiKe Protection Circuitry is not enabled. The waveform to the right of the SOA graph exemplifies how the dynamic protection will cause waveform distortion when enabled. Please refer to AN-898 for more detailed information. THERMAL PROTECTION The LM4766 has a sophisticated thermal protection scheme to prevent long-term thermal stress of the device. When the temperature on the die reaches 165C, the LM4766 shuts down. It starts operating again when the die temperature drops to about 155C, but if the temperature again begins to rise, shutdown will occur again at 165C. Therefore, the device is allowed to heat up to a relatively high temperature if the fault condition is temporary, but a sustained fault will cause the device to cycle in a Schmitt Trigger fashion between the thermal shutdown temperature limits of 165C and 10092852 Once the maximum package power dissipation has been calculated using Equation (1), the maximum thermal resistance, SA, (heat sink to ambient) in C/W for a heat sink can be calculated. This calculation is made using Equation (3) which is derived by solving for SA in Equation (2). (3) SA = [(TJMAX-TAMB)-PDMAX(JC +CS)]/PDMAX 15 www.national.com LM4766 155C. This greatly reduces the stress imposed on the IC by thermal cycling, which in turn improves its reliability under sustained fault conditions. Since the die temperature is directly dependent upon the heat sink used, the heat sink should be chosen such that thermal shutdown will not be reached during normal operation. Using the best heat sink possible within the cost and space constraints of the system will improve the long-term reliability of any power semiconductor device, as discussed in the Determining the Correct Heat Sink Section. Application Information LM4766 Application Information This value of PDMAX can be used to calculate the correct size heat sink for a bridged amplifier application. Since the internal dissipation for a given power supply and load is increased by using bridged-mode, the heatsink's SA will have to decrease accordingly as shown by Equation (3). Refer to the section, Determining the Correct Heat Sink, for a more detailed discussion of proper heat sinking for a given application. (Continued) Again it must be noted that the value of SA is dependent upon the system designer's amplifier requirements. If the ambient temperature that the audio amplifier is to be working under is higher than 25C, then the thermal resistance for the heat sink, given all other things are equal, will need to be smaller. SUPPLY BYPASSING The LM4766 has excellent power supply rejection and does not require a regulated supply. However, to improve system performance as well as eliminate possible oscillations, the LM4766 should have its supply leads bypassed with lowinductance capacitors having short leads that are located close to the package terminals. Inadequate power supply bypassing will manifest itself by a low frequency oscillation known as "motorboating" or by high frequency instabilities. These instabilities can be eliminated through multiple bypassing utilizing a large tantalum or electrolytic capacitor (10F or larger) which is used to absorb low frequency variations and a small ceramic capacitor (0.1F) to prevent any high frequency feedback through the power supply lines. If adequate bypassing is not provided, the current in the supply leads which is a rectified component of the load current may be fed back into internal circuitry. This signal causes distortion at high frequencies requiring that the supplies be bypassed at the package terminals with an electrolytic capacitor of 470F or more. SINGLE-SUPPLY AMPLIFIER APPLICATION The typical application of the LM4766 is a split supply amplifier. But as shown in Figure 3, the LM4766 can also be used in a single power supply configuration. This involves using some external components to create a half-supply bias which is used as the reference for the inputs and outputs. Thus, the signal will swing around half-supply much like it swings around ground in a split-supply application. Along with proper circuit biasing, a few other considerations must be accounted for to take advantage of all of the LM4766 functions, like the mute function. CLICKS AND POPS In the typical application of the LM4766 as a split-supply audio power amplifier, the IC exhibits excellent "click" and "pop" performance when utilizing the mute mode. In addition, the device employs Under-Voltage Protection, which eliminates unwanted power-up and power-down transients. The basis for these functions are a stable and constant halfsupply potential. In a split-supply application, ground is the stable half-supply potential. But in a single-supply application, the half-supply needs to charge up just like the supply rail, VCC. This makes the task of attaining a clickless and popless turn-on more challenging. Any uneven charging of the amplifier inputs will result in output clicks and pops due to the differential input topology of the LM4766. To achieve a transient free power-up and power-down, the voltage seen at the input terminals should be ideally the same. Such a signal will be common-mode in nature, and will be rejected by the LM4766. In Figure 3, the resistor RINP serves to keep the inputs at the same potential by limiting the voltage difference possible between the two nodes. This should significantly reduce any type of turn-on pop, due to an uneven charging of the amplifier inputs. This charging is based on a specific application loading and thus, the system designer may need to adjust these values for optimal performance. As shown in Figure 3, the resistors labeled RBI help bias up the LM4766 off the half-supply node at the emitter of the 2N3904. But due to the input and output coupling capacitors in the circuit, along with the negative feedback, there are two different values of RBI, namely 10k and 200k. These resistors bring up the inputs at the same rate resulting in a popless turn-on. Adjusting these resistors values slightly may reduce pops resulting from power supplies that ramp extremely quick or exhibit overshoot during system turn-on. BRIDGED AMPLIFIER APPLICATION The LM4766 has two operational amplifiers internally, allowing for a few different amplifier configurations. One of these configurations is referred to as "bridged mode" and involves driving the load differentially through the LM4766's outputs. This configuration is shown in Figure 2. Bridged mode operation is different from the classical single-ended amplifier configuration where one side of its load is connected to ground. A bridge amplifier design has a distinct advantage over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Consequently, theoretically four times the output power is possible as compared to a single-ended amplifier under the same conditions. This increase in attainable output power assumes that the amplifier is not current limited or clipped. A direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation. For each operational amplifier in a bridge configuration, the internal power dissipation will increase by a factor of two over the single ended dissipation. Thus, for an audio power amplifier such as the LM4766, which has two operational amplifiers in one package, the package dissipation will increase by a factor of four. To calculate the LM4766's maximum power dissipation point for a bridged load, multiply Equation (1) by a factor of four. www.national.com 16 into an 8 load the IOPEAK drawn from the supplies is twice 2.74APK or 5.48APK. At this point it is a good idea to check the Power Output vs Supply Voltage to ensure that the required output power is obtainable from the device while maintaining low THD+N. In addition, the designer should verify that with the required power supply voltage and load impedance, that the required heatsink value SA is feasible given system cost and size constraints. Once the heatsink issues have been addressed, the required gain can be determined from Equation (6). (Continued) AUDIO POWER AMPLlFIER DESIGN Design a 30W/8 Audio Amplifier Given: Power Output Load Impedance Input Level Input Impedance Bandwidth 30Wrms 8 1Vrms(max) 47k 20Hz-20kHz 0.25dB (6) From Equation (6), the minimum AV is: AV 15.5. By selecting a gain of 21, and with a feedback resistor, Rf = 20k, the value of Ri follows from Equation (7). Ri = Rf (AV - 1) (7) Thus with Ri = 1k a non-inverting gain of 21 will result. Since the desired input impedance was 47k, a value of 47k was selected for RIN. The final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency points. Five times away from a -3dB point is 0.17dB down from passband response which is better than the required 0.25dB specified. This fact results in a low and high frequency pole of 4Hz and 100kHz respectively. As stated in the External Components section, Ri in conjunction with Ci create a high-pass filter. use 39F. Ci 1/(2 * 1k * 4Hz) = 39.8F; The high frequency pole is determined by the product of the desired high frequency pole, fH, and the gain, AV. With a AV = 21 and fH = 100kHz, the resulting GBWP is 2.1MHz, which is less than the guaranteed minimum GBWP of the LM4766 of 8MHz. This will ensure that the high frequency response of the amplifier will be no worse than 0.17dB down at 20kHz which is well within the bandwidth requirements of the design. A designer must first determine the power supply requirements in terms of both voltage and current needed to obtain the specified output power. VOPEAK can be determined from Equation (4) and IOPEAK from Equation (5). (4) (5) To determine the maximum supply voltage the following conditions must be considered. Add the dropout voltage to the peak output swing VOPEAK, to get the supply rail at a current of IOPEAK. The regulation of the supply determines the unloaded voltage which is usually about 15% higher. The supply voltage will also rise 10% during high line conditions. Therefore the maximum supply voltage is obtained from the following equation. Max supplies (VOPEAK + VOD) (1 + regulation) (1.1) For 30W of output power into an 8 load, the required VOPEAK is 21.91V. A minimum supply rail of 25.4V results from adding VOPEAK and VOD. With regulation, the maximum supplies are 32V and the required IOPEAK is 2.74A from Equation (5). It should be noted that for a dual 30W amplifier 17 www.national.com LM4766 Application Information LM4766 Physical Dimensions inches (millimeters) unless otherwise noted Non-Isolated TO-220 15-Lead Package Order Number LM4766T NS Package Number TA15A www.national.com 18 LM4766 OvertureTM Audio Power Amplifier Series Dual 40W Audio Power Amplifier with Mute Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Isolated TO-220 15-Lead Package Order Number LM4766TF NS Package Number TF15B National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. Leadfree products are RoHS compliant. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated