SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET KEY FEATURES DESCRIPTION All protective features of thermal shutdown, current limiting, and safe-area control have been designed into these units and since these regulators require only a small output capacitor for satisfactory performance, ease of application is assured. Although designed as fixed-voltage regulators, the output voltage can be increased through the use of a simple voltage divider. The low quiescent drain current of the device insures good regulation when this method is used. Product is available in hermetically sealed TO-257 (both case grounded `G' and isolated `IG'), TO-3, TO-39 and LCC packages. IMPORTANT: For the most current data, consult MICROSEMI's website: http://www.microsemi.com Output Voltage Set Internally to 1.5% on SG78xxA Input Voltage Range to 50V max. on SG78xxA Two Volt Input-Output Differential Excellent Line and Load Regulation Foldback Current Limiting Thermal Overload Protection Voltages Available: 5V, 12V, 15V Contact Factory for Other Voltage Options Available in Surface Mount Package HIGH RELIABILITY FEATURES - SG78xxA/78xx WWW . Microsemi .C OM The SG78xxA/SG78xx series of positive regulators offer self contained, fixed-voltage capability with up to 1.5A of load current and input voltage up to 50V (SG78xxA series only). These units feature a unique on-chip trimming system to set the output voltages to within 1.5% of nominal on the SG78xxA series, 2.0% on the SG78xx series. The SG78xxA versions also offer much improved line and load regulation characteristics. Utilizing an improved bandgap reference design, problems have been eliminated that are normally associated with the Zener diode references, such as drift in output voltage and large changes in the line and load regulation. Available to MIL-STD - 883, 1.2.1 MIL-M38510/10702BXA - JAN7805T MIL-M38510/10703BXA - JAN7812T MIL-M38510/10704BXA - JAN7815T MIL-M38510/10706BYA - JAN7805K MIL-M38510/10707BYA - JAN7812K MIL-M38510/10708BYA - JAN7815K Radiation Data Available MSC-AMSG level "S" Processing Available Available to DSCC - Standard Microcircuit Drawing (SMD) PRODUCT HIGHLIGHT SCHEMATIC DIAGRAM * SG78XX * For normal operation the (VOS) sense pin must be externally connected to the load. Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 1 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET ABSOLUTE MAXIMUM RATINGS Input Voltage 5V 12V 15V 35V 35V 35V Input Voltage (Transient)(Note 3) 50V 50V 50V Input Voltage Differential (Output Shorted to Ground) 35V 35V 35V Operating Junction Temperature .........................................................................................................................................................150C Storage Temperature Range ................................................................................................................................................. -65C to 150C Lead Temperature (Soldering 10 seconds) ..........................................................................................................................................300C Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal. WWW . Microsemi .C OM Device Output Voltage Note 3: Operation at high input voltages is dependent upon load current. When load current is less than 5mA, output will rise out of regulation as inputoutput differential increases beyond 30V. Note also from figure 1, that maximum load current is reduced at high voltages. The 50V input rating of the SG78xxA series refers to ability to withstand high line or transient conditions without damage. Since the regulator's maximum current capability is reduced, the output may fall out of regulation at high input voltages under nominal loading. THERMAL DATA K TO-3 3-Terminal Metal Can (Two pins and case) THERMAL RESISTANCE-JUNCTION TO CASE, JC THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA T TO-39 3-Pin Metal Can THERMAL RESISTANCE-JUNCTION TO CASE, JC THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA G THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA 3.5C/W 42C/W TO-257 3-Pin Hermetic (Isolated) THERMAL RESISTANCE-JUNCTION TO CASE, JC THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA 4.0C/W 42C/W Leadless Chip Carrier 20-Pin Ceramic THERMAL RESISTANCE-JUNCTION TO CASE, JC THERMAL RESISTANCE-JUNCTION TO AMBIENT, JA PACKAGE DATA L 15C/W 120C/W TO-257 3-Pin Hermetic THERMAL RESISTANCE-JUNCTION TO CASE, JC IG 3.0C/W 35C/W 35C/W 120C/W Junction Temperature Calculation: TJ = TA + (PD x JA). The JA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow. Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 2 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET CHARACTERISTIC CURVES WWW . Microsemi .C OM Figure 1 - Peak Output Current vs. Input - Output Differential Figure 2 - Minimum Input - Output Voltage vs. Load Current Figure 3 - Ripple Rejection vs. Frequency Figure 4 - Temperature Coefficient of Output Voltage GRAPHS Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 3 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET APPLICATIONS WWW . Microsemi .C OM Figure 5 - Fixed Output Regulator Figure 6 - Circuit for Increasing Output Voltage Figure 7 - High Output Current, Short Circuit Protected Figure 8 - Adjustable Output Regulator, 7V to 30V RECOMMENDED OPERATING CONDITIONS SG78xx / 78xxA Min Typ Max 55 150 Parameter Operating Junction Temperature Range (Note 2) Units C Note 2: Range over which the device is functional. APPLICATIONS Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 4 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET Parameter Test Conditions Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Note TJ = 25C VIN = 7.5V to 20V, TJ = 25C VIN = 8V to 12V, TJ = 25C Power Pkgs: IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C T - Pkg: IO = 5mA to 500mA, TJ = 250C VIN = 8V to 20V Power Pkgs: IO = 5mA to 1.0A, P < 20W T - Pkg: IO =5mA to 500mA, P < 20W Over Temperature Range TJ = 25C With Line: VIN = 8V to 25V With Load: IO = 5mA to 1.0A (Power Pkgs.) IO = 5mA to 500mA (T) VO = 100mV, TJ = 25C Power Pkgs: IO = 1.0A, T-Pkg: IO = 500mA Power Pkgs: VIN = 10V, TJ = 25C T - Pkg: VIN = 10V, TJ = 25C Power Pkgs: VIN = 35V, TJ = 25C T - Pkg: VIN = 35V, TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100kHz (Note 2) 1000 hours @ TJ = 125C IO = 5mA Min 4.92 4.85 4.85 SG7805A Typ Max 5.00 5.08 5 25 2 12 15 50 5 25 5 25 5.00 5.00 4 1.5 0.5 2 2.0 1.0 5.15 5.15 7 6 0.8 0.5 0.5 2.5 3.3 2.0 1.2 0.7 68 Min 4.80 4.65 4.65 SG7805 Typ 5.00 5 2 15 5 20 5.00 5.00 4 1.5 0.5 2 2.0 1.0 Units Max 5.20 25 25 50 25 25 V mV mV mV mV mV 5.35 5.35 7 6 0.8 0.5 0.5 V V mA mA mA mA mA 2.5 3.3 2.0 1.2 0.7 V A A A A dB V/V mV C 68 40 20 175 40 20 175 WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7805A / SG7805 with -55C < TA < 125C, VIN = 10V, IO = 500mA for the K, G and IG - Power Packages, IO = 100mA for the T and L packages, CIN = 0.33F, and COUT = 0.1F. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature. 1: All regulation tests are made at constant junction temperature with low duty cycle testing. 2: This test is guaranteed but is not tested in production. ELECTRICALS Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 5 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET Parameter Test Conditions Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Note TJ = 25C VIN = 14.5V to 30V, TJ = 25C VIN = 16V to 22V, TJ = 25C Power Pkgs: IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C T - Pkg: IO = 5mA to 500mA, TJ = 25C VIN = 15.5V to 27V Power Pkgs: IO = 5mA to 1.0A, P < 20W T - Pkg: IO = 5mA to 500mA, P < 2W Over Temperature Range TJ = 25C With Line: VIN = 15V to 30V With Load: IO = 5mA to 1.0A (Power Pkgs.) IO = 5mA to 500mA (T) VO = 100mV, TJ = 25C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25C T - Pkg: TJ = 25C Power Pkgs: VIN = 35V, TJ = 25C T - Pkg: VIN = 35V, TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100kHz (note 2) 1000 hours @ TJ = 125C IO = 5mA Min 11.8 11.7 11.7 SG7812A Typ Max 12.0 12.2 12 60 6 30 28 80 10 40 10 40 12.0 12.0 4 1.5 0.5 2 2.0 1.0 12.3 12.3 7 6 0.8 0.5 0.5 2.5 3.3 1.7 1.2 0.7 61 Min 11.5 11.4 11.4 SG7812 Typ 12.0 12 6 28 10 10 12.0 12.0 4 1.5 0.5 2 2.0 1.0 Units Max 12.5 120 60 120 60 60 V mV mV mV mV mV 12.6 12.6 7 6 0.8 0.5 0.5 V V mA mA mA mA mA 2.5 3.3 1.7 1.2 0.7 V A A A A dB V/V mV C 61 40 48 175 40 48 175 WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7812A / SG7812 with -55C < TA < 125C, VIN = 19V, IO = 500mA for the K, G and IG - Power Packages, IO = 100mA for the T and L packages, CIN = 0.33F, and COUT = 0.1F. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature. 1: All regulation tests are made at constant junction temperature with low duty cycle testing. 2: This test is guaranteed but is not tested in production. ELECTRICALS Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 6 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET Parameter Test Conditions Output Voltage Line Regulation (Note 1) Load Regulation (Note 1) Total Output Voltage Tolerance Quiescent Current Quiescent Current Change Dropout Voltage Peak Output Current Short Circuit Current Ripple Rejection Output Noise Voltage (rms) Long Term Stability Thermal Shutdown Note TJ = 25C VIN = 17.5V to 30V, TJ = 25C VIN = 20V to 26V, TJ = 25C Power Pkgs: IO = 5mA to 1.5A, TJ = 25C IO = 250mA to 750mA, TJ = 25C T - Pkg: IO = 5mA to 500mA, TJ = 25C VIN = 18.5V to 30V Power Pkgs: IO = 5mA to 1.0A, P < 20W T - Pkg: IO = 5mA to 500mA, P < 2W Over Temperature Range TJ = 25C With Line: VIN = 18.5V to 30V With Load: IO = 5mA to 1.0A (Power Pkgs) IO = 5mA to 500mA (T) VO = 100mV, TJ = 25C Power Pkgs: IO = 1.0A, T - Pkg: IO = 500mA Power Pkgs: TJ = 25C T - Pkg: TJ = 25C Power Pkgs: VIN = 35V, TJ = 25C T - Pkg: VIN = 35V, TJ = 25C VIN = 10V, f = 120Hz, TJ = 25C f = 10Hz to 100kHz (note 2) 1000 hours @ TJ = 125C IO = 5mA Min 14.8 14.6 14.6 SG7815A Typ Max 15.0 15.2 15 75 8 40 30 100 12 50 12 50 15.0 15.0 4 1.5 0.5 2 2.2 0.9 15.4 15.4 7 6 0.8 0.5 0.5 2.5 3.3 1.7 1.2 0.7 60 Min 14.4 14.3 14.3 SG7815 Typ 15.0 15 8 30 12 12 15.0 15.0 4 1.5 0.5 2 2.2 0.9 Units Max 15.6 150 75 150 75 75 V mV mV mV mV 15.7 15.7 7 6 0.8 0.5 0.5 V V mA mA mA mA mA 2.5 3.3 1.7 1.2 0.7 V A A A A dB V/V mV 60 40 60 175 40 60 175 WWW . Microsemi .C OM ELECTRICAL CHARACTERISTICS Unless otherwise specified, these specifications apply over the operating ambient temperatures for SG7815A / SG7815 with -55C < TA < 125C, VIN = 23V, IO = 500mA for the K, G and IG - Power Packages, IO = 100mA for the T and L packages, CIN = 0.33F, and COUT = 0.1F. Low duty cycle pulse testing techniques are used which maintains junction and case temperatures equal to the ambient temperature. 1: All regulation tests are made at constant junction temperature with low duty cycle testing. 2: This test is guaranteed but is not tested in production. NOTES ELECTRICALS Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 7 SG78xxA/78xx (R) TM Positive Fixed Voltage Regulator P RODUCT D ATASHEET CONNECTION DIAGRAMS & ORDERING INFORMATION (SEE NOTES BELOW) 2 VOUT Case is Ground 1 VIN 2 VOUT 3 GND Case is Ground VOUT N.C. N.C. N.C. GROUND VIN 3 2 1 20 19 4 18 N.C. N.C. 5 17 VIN N.C. 6 16 N.C. GND 7 15 VO SENSE N.C. 8 14 N.C. N.C. 9 10 11 12 13 N.C. N.C. VOUT 20-Pin Ceramic Leadless Chip Carrier L - Package 1 VIN 3-Pin Hermetic TO-257 IG - Package (Isolated) VIN N.C. 3-Pin TO-39 Metal Can T - Package Connection Diagram N.C. 3-Terminal TO-3 Metal Can K - Package SG78xxAK/883B SG7805AK/DESC SG7812AK/DESC SG7815AK/DESC SG78xxAK SG78xxK/883B JAN7805K JAN7812K JAN7815K SG78xxK SG78xxAT/883B SG7805AT/DESC SG7812AT/DESC SG7815AT/DESC SG78xxAT SG78xxT/883B JAN7805T JAN7812T JAN7815T SG78xxT SG78xxAIG/883B SG7805AIG/DESC SG7812AIG/DESC SG7815AIG/DESC SG78xxAIG SG78xxIG/883B SG78xxIG SG7805AL/DESC SG7812AL/DESC SG7815AL/DESC SG78xxL/883B Ambient Temperature Range -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C VOUT Part No. WWW . Microsemi .C OM Package See Notes 5 & 6 3-Pin Hermetic TO-257 G - Package (Case is Ground) -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C -55C to 125C VOUT GROUND VIN Case is Ground MECHANICALS Note SG78xxAG/883B SG7805AG/DESC SG7812AG/DESC SG7815AG/DESC SG78xxAG SG78xxG/883B SG78xxG 1: Contact factory for JAN and DESC product availability. 2: All parts are viewed from the top. 3: "xx" to be replaced by output voltage of specific fixed regulator. 4: Some products will be available in hermetic flat pack (F). Consult factory for price and availability. 5: Both inputs and outputs must be externally connected together at the device terminals. 6: For normal operation, the VO SENSE pin must be externally connected to the load. Copyright (c) 1997 Rev. 1.5, 2010-07-13 Microsemi Analog Mixed Signal Group 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570 Page 8