FUNCTIONAL BLOCK DIAGRAM APPLICATIONS 1 2 3 4 5 6 7 8 HMC1163 NC 9 NC 10 GND 11 RFOUT/2 12 NC 13 NC 14 NC 15 NC 16 Point to point and multipoint radios Test equipment and industrial controls Very small aperture terminals (VSATs) NC NC NC NC GND NC NC NC 24 23 22 21 20 19 18 17 NC NC NC VCC NC RFOUT NC NC 13871-001 Dual output frequency range fOUT = 9.65 GHz to 10.41 GHz fOUT/2 = 4.825 GHz to 5.205 GHz Output power (POUT): 11 dBm Single-sideband (SSB) phase noise: -114 dBc/Hz at 100 kHz No external resonator needed RoHS compliant, 5 mm x 5 mm, 32-lead LFCSP: 25 mm NC NC NC VTUNE NC NC NC NC FEATURES 32 31 30 29 28 27 26 25 Data Sheet 9.65 GHz to 10.41 GHz MMIC VCO with Half Frequency Output HMC1163 Figure 1. GENERAL DESCRIPTION The HMC1163 is a monolithic microwave integrated circuit (MMIC), voltage controlled oscillator (VCO) that integrates a resonator, a negative resistance device, and a varactor diode, and features a half frequency output. Rev. 0 Because of the monolithic construction of the oscillator, the output power and phase noise performance are excellent over temperature. The output power is 11 dBm typical from a 5 V supply voltage. The VCO is housed in a RoHS compliant LFCSP and requires no external matching components. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com HMC1163 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Typical Performance Characteristics ..............................................7 Applications ....................................................................................... 1 Theory of Operation .........................................................................9 Functional Block Diagram .............................................................. 1 Applications Information .............................................................. 10 General Description ......................................................................... 1 Evaluation Printed Circuit Board (PCB) ..................................... 11 Revision History ............................................................................... 2 Bill of Materials ........................................................................... 11 Specifications..................................................................................... 3 Packaging and Ordering Information ......................................... 12 Absolute Maximum Ratings ....................................................... 4 Outline Dimensions ................................................................... 12 ESD Caution .................................................................................. 4 Ordering Guide .......................................................................... 12 Pin Configuration and Function Descriptions ............................. 5 Interface Schematics..................................................................... 6 REVISION HISTORY 3/16--Revision 0: Initial Version Rev. 0 | Page 2 of 12 Data Sheet HMC1163 SPECIFICATIONS TA = -40C to +85C, VCC = 5 V, unless otherwise noted. Table 1. Parameter FREQUENCY Range Output Frequency (fOUT) Half Output Frequency (fOUT/2) Drift Rate Pulling Pushing OUTPUT POWER (POUT) RFOUT RFOUT/2 Supply Current (ICC) HARMONICS, SUBHARMONICS 1/2 3/2 Second Third TUNING Voltage (VTUNE) Sensitivity Tune Port Leakage Current OUTPUT RETURN LOSS SSB PHASE NOISE 10 kHz Offset 100 kHz Offset Min Typ 9.65 4.825 Max Unit Test Conditions/Comments 10.41 6.665 GHz GHz MHz/C MHz p-p MHz/V Pulling into a 2.0:1 voltage standing wave ratio (VSWR) At VTUNE = 5 V dBm dBm mA mA mA VCC = 4.75 V VCC = 5.00 V VCC = 5.25 V 1.0 2 7 7 2 11 6 185 205 230 15 11 250 40 29 19 23 2 75 dBc dBc dBc dBc 13 300 10 V MHz/V A dB -85 -112 dBc/Hz dBc/Hz 6 -87 -114 Rev. 0 | Page 3 of 12 VTUNE = 13 V HMC1163 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VCC VTUNE Operating Temperature Range Storage Temperature Range Nominal Junction Temperature (to Maintain 1 Million Hours Mean Time to Failure (MTTF)) Nominal Junction Temperature (TA = 85C) Maximum Reflow Temperature (MSL3 Rating) Thermal Resistance (Junction to Ground Pad) ESD Sensitivity Human Body Model (HBM) Field Induced Charged Device Model (FICDM) Rating 5.5 V dc 0 V to 15 V -40C to +85C -65C to +150C 135C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION 116.3C 260C 24.7C/W 300 V (Class 1A) 300 V (Class II) Rev. 0 | Page 4 of 12 Data Sheet HMC1163 32 31 30 29 28 27 26 25 NC NC NC VTUNE NC NC NC NC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 HMC1163 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 NC NC NC VCC NC RFOUT NC NC NOTES 1. NC = NO CONNECT. HOWEVER, THESE PINS CAN BE CONNECTED TO RF/DC GROUND WITHOUT AFFECTING THE PERFORMANCE OF THE DEVICE. 2. EXPOSED PAD. THE PACKAGE BOTTOM HAS AN EXPOSED METAL PAD THAT MUST BE CONNECTED TO RF/DC GROUND. 13871-002 NC 9 NC 10 GND 11 RFOUT/2 12 NC 13 NC 14 NC 15 NC 16 NC NC NC NC GND NC NC NC Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 to 4, 6 to 10, 13 to 18, 20, 22 to 28, 30 to 32 5, 11 12 19 21 29 Mnemonic NC GND RFOUT/2 RFOUT VCC VTUNE EP Description No Connect. However, these pins can be connected to RF/dc ground without affecting the performance of the device. Ground. These pins must be connected to RF/dc ground. Half Radio Frequency Output. This pin is ac-coupled. Radio Frequency Output. This pin is ac-coupled. Supply Voltage (5 V). Control Voltage and Modulation Input. The modulation bandwidth is dependent on the drive source impedance. Exposed Pad. The package bottom has an exposed metal pad that must be connected to RF/dc ground. Rev. 0 | Page 5 of 12 HMC1163 Data Sheet INTERFACE SCHEMATICS 3nH RFOUT 4pF Figure 3. RFOUT Interface GND Figure 7. GND Interface Figure 4. RFOUT/2 Interface 15pF 13871-005 VCC 13871-007 Figure 6. VTUNE Interface 13871-004 RFOUT/2 80pF Figure 5. VCC Interface Rev. 0 | Page 6 of 12 13871-006 13871-003 VTUNE Data Sheet HMC1163 TYPICAL PERFORMANCE CHARACTERISTICS 10.8 260 +85C +25C -40C 10.6 +85C +25C -40C 250 10.2 240 10.0 9.8 CURRENT (mA) OUTPUT FREQUENCY (GHz) 10.4 9.6 9.4 9.2 9.0 8.8 230 220 210 200 8.6 8.4 190 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) 180 0 5.2 OUTPUT FREQUENCY (GHz) 12 10 8 6 4 0 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) 5 6 7 8 9 10 11 12 13 5.0 4.8 4.6 4.4 +85C +25C -40C 4.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 TUNING VOLTAGE (V dc) Figure 12. RFOUT/2 Output Frequency vs. Tuning Voltage Figure 9. Output Power vs. Tuning Voltage 10 900 +85C +25C -40C 800 9 8 600 500 400 300 7 6 5 4 3 200 2 100 1 0 1 2 3 4 5 6 7 8 9 10 TUNING VOLTAGE (V dc) 11 12 13 0 13871-010 0 +85C +25C -40C 0 1 2 3 4 5 6 7 8 9 10 11 12 TUNING VOLTAGE (V dc) Figure 10. Sensitivity vs. Tuning Voltage Figure 13. RFOUT/2 Output Power vs. Tuning Voltage Rev. 0 | Page 7 of 12 13 13871-013 OUTPUT POWER (dBm) 700 SENSITIVITY (MHz/V) 4 4.2 +85C +25C -40C 13871-009 OUTPUT POWER (dBm) 5.4 1 3 Figure 11. Supply Current (ICC) vs. Tuning Voltage 14 0 2 TUNING VOLTAGE (V dc) Figure 8. Output Frequency vs. Tuning Voltage 2 1 13871-012 0 13871-008 8.0 13871-011 8.2 HMC1163 Data Sheet -70 -40 +85C +25C -40C -75 -50 -60 -85 -90 -95 -100 -105 -110 100kHz -70 -80 -90 -100 -110 -120 -130 -115 -140 -120 -150 -125 0 1 2 3 4 5 6 7 8 9 10 11 TUNING VOLTAGE (V dc) 12 13 -160 1k +85C +25C -40C 10k 100k 1M OFFSET FREQUENCY (Hz) Figure 14. SSB Phase Noise vs. Tuning Voltage Figure 15. SSB Phase Noise vs. Offset Frequency at VTUNE = 5 V Rev. 0 | Page 8 of 12 13871-015 SSB PHASE NOISE (dBc/Hz) 10kHz 13871-014 SSB PHASE NOISE (dBc/Hz) -80 Data Sheet HMC1163 THEORY OF OPERATION The HMC1163 voltage controlled oscillator is a free running voltage controlled frequency source. The output frequency is controlled by applying a variable tune voltage to the VTUNE port. Because VTUNE is varied from the lowest to the highest allowed voltage, the VCO output frequency increases from the lowest to the highest operating frequency. This VCO output frequency change with the applied VTUNE input results in the VCO frequency sensitivity characteristic (MHz/V). The VCO frequency sensitivity is not constant and varies across the tunable range. The HMC1163 VCO is specified to cover the minimum to maximum frequencies specified in this data sheet over the entire specified temperature range, including the VCO frequency drift (MHz/C). In addition, for low phase noise operation, drive the VTUNE port from a low noise voltage source. Excessive noise on the VTUNE port results in poor phase noise performance. The tune port modulation bandwidth is typically greater than 10 MHz. To achieve optimum VCO phase noise performance when using the HMC1163, it is important to use a low noise power supply for VCC biasing. Because the VCO output frequency changes with small changes in the VCC bias voltage (pushing), noise on the VCC bias pin results in increased phase noise. Take care to use low noise regulators, otherwise, bias line noise may corrupt the low phase noise output of the HMC1163. Internally, the radio frequency (RF) output frequency is generated from a doubler circuit. This generation results in an unwanted low level output signal present at half the RFOUT frequency (RFOUT/2). If necessary, this undesired spurious signal can be further filtered on the customer application board using a filter. The RFOUT/2 output signal is available directly at the RFOUT/2 port. The RFOUT/2 port commonly drives a phaselocked loop (PLL)/ synthesizer for phase locking the HMC1163 output if needed. Lastly, the HMC1163 RFOUT port incorporates an internal buffer amplifier to provide good output matching. The internal buffer amplifier also isolates the VCO core from the output load and minimizes the VCO frequency change with the changes to the output load impedance (pulling). Rev. 0 | Page 9 of 12 HMC1163 Data Sheet APPLICATIONS INFORMATION The HMC1163 serves as the local oscillator (LO) in microwave synthesizer applications. The primary applications are point to point microwave radios, military, radars, test and measurement, as well as industrial and medical equipment. The low phase noise allows higher orders of modulation and offers improved bit error rates in communication systems, whereas the linear, monotonic tuning sensitivity allows a stable loop filter design. The higher output power minimizes the gain required to drive subsequent stages. The half frequency output reduces the input frequency to the prescaler without the addition of residual phase noise to the input of the phase-locked loop synthesizer. LOOP FILTER HOST SCK SDI SEN SYNTH CP RFOUT RFOUT/2 REF XREFP VCO INPUT Figure 16. Typical Application Diagram Rev. 0 | Page 10 of 12 13871-016 VTUNE Data Sheet HMC1163 13871-017 EVALUATION PRINTED CIRCUIT BOARD (PCB) Figure 17. Evaluation PCB The circuit board used in an application uses RF circuit design techniques. Ensure that the signal lines have 50 impedance and that the package ground leads and backside ground paddle are connected directly to the ground plane. Use a sufficient number of via holes to connect the top and bottom ground planes. The evaluation circuit board shown in Figure 17 is available from Analog Devices, Inc., upon request. BILL OF MATERIALS Table 4. Bill of Materials for the EV1HMC1163LP5 Item J1 to J4 J5, J6 C1 to C3 C4 C5 to C7 C8 U1 PCB1 1 2 Description PCB mount SMA RF connectors 2 mm dc headers 100 pF capacitors, 0402 package 1000 pF capacitor, 0402 package 2.2 F tantalum capacitors 0.01 F capacitor, 0603 package HMC1163 VCO 110225 evaluation board2 Circuit board material is Rogers 4350. Reference this number when ordering the complete evaluation PCB. Rev. 0 | Page 11 of 12 HMC1163 Data Sheet PACKAGING AND ORDERING INFORMATION OUTLINE DIMENSIONS 0.30 0.25 0.18 1 24 0.50 BSC 3.80 3.65 SQ 3.50 EXPOSED PAD 17 TOP VIEW 1.00 0.90 0.80 8 16 9 BOTTOM VIEW 3.50 REF 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE PKG-000000 0.45 0.40 0.35 PIN 1 INDICATOR 32 25 0.20 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 03-04-2015-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-4. Figure 18. 32-Lead Lead Frame Chip Scale Package [LFCSP] 5 mm x 5 mm Body and 0.90 mm Package Height (HCP-32-1) Dimensions shown in millimeters ORDERING GUIDE Model1 HMC1163LP5E Temperature Range -40C to +85C MSL Rating2 MSL3 Package Description 32-Lead LFCSP Package Option HCP-32-1 Qty. HMC1163LP5ETR -40C to +85C MSL3 32-Lead LFCSP, 7" Tape and Reel HCP-32-1 500 EV1HMC1163LP5 1 2 3 Evaluation Board The HMC1163LP5E and HMC1163LP5ETR are RoHS compliant parts. See the Absolute Maximum Ratings section, Table 2. XXXX is a placeholder for the 4-digit lot number. (c)2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D13871-0-3/16(0) Rev. 0 | Page 12 of 12 Branding3 H1163 XXXX H1163 XXXX