DATA SH EET
Product specification
Supersedes data of 1997 Feb 12
File under Integrated Circuits, IC01
1998 Sep 23
INTEGRATED CIRCUITS
TDA8567Q
4×25 W BTL quad car radio power
amplifier
1998 Sep 23 2
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
FEATURES
•Requires very few external components
•High output power
•Low output offset voltage
•Fixed gain
•Diagnostic facility (distortion, short-circuit and
temperature pre-warning)
•Good ripple rejection
•Mode select switch (operating, mute and standby)
•Load dump protection
•Short-circuit safe to ground and to VP and across the
load
•Low power dissipation in any short-circuit condition
•Thermally protected
•Reverse polarity safe
•Electrostatic discharge protection
•No switch-on/switch-off plop
•Flexible leads
•Low thermal resistance
•Pin compatible with the TDA8568Q, except for the gain.
GENERAL DESCRIPTION
The TDA8567Q is an integrated class-B output amplifier in
a 23-lead Single-In-Line (SIL) plastic power package.
It contains four amplifiers in BTL configuration, each with a
gain of 26 dB. The output power is 4 ×25 W in a 4 Ω load.
APPLICATIONS
•The device is primarily developed for car radio
applications.
QUICK REFERENCE DATA
ORDERING INFORMATION
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
VPoperating supply voltage 6 14.4 18 V
IORM repetitive peak output current −−7.5 A
Iq(tot) total quiescent current −230 −mA
Istb standby current −0.2 100 µA
Isw switch-on current −−80 µA
Ziinput impedance 25 30 −kΩ
Pooutput power THD = 10% −25 −W
SVRR supply voltage ripple rejection Rs=0Ω−60 −dB
αcs channel separation Rs=10kΩ−50 −dB
Gvclosed loop voltage gain 25 26 27 dB
Vn(o) noise output voltage Rs=0Ω −−120 µV
∆VODC output offset voltage −−150 mV
TYPE
NUMBER PACKAGE
NAME DESCRIPTION VERSION
TDA8567Q DBS23P plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1
1998 Sep 23 3
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
BLOCK DIAGRAM
Fig.1 Block diagram.
handbook, full pagewidth
MGG153
OUT1+
OUT1−
+
−
+
−
Vref
2
IN1
IN2
4
23168115
10
MODE VP1 VP2 VP3 VP4
211863
PGND1 PGND2 PGND3 PGND4
30 kΩ
OUT2+
OUT2−
+
−
+
−
7
5
11
30 kΩ
OUT3+
OUT3−
+
−
+
−
Vref
17
IN3
SGND
TDA8567Q
IN4
19
13
12
30 kΩ
OUT4+
OUT4−
+
−
+
−
22
20
14
30 kΩ
VDIAG
DIAGNOSTIC 9
1998 Sep 23 4
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
PINNING
SYMBOL PIN DESCRIPTION
VP1 1 supply voltage 1
OUT1+ 2 output 1+
PGND1 3 power ground 1
OUT1−4 output 1−
OUT2−5 output 2−
PGND2 6 power ground 2
OUT2+ 7 output 2+
VP2 8 supply voltage 2
VDIAG 9 diagnostic output
IN1 10 input 1
IN2 11 input 2
SGND 12 signal ground
IN3 13 input 3
IN4 14 input 4
MODE 15 mode select switch input
VP3 16 supply voltage 3
OUT3+ 17 output 3+
PGND3 18 power ground 3
OUT3−19 output 3−
OUT4−20 output 4−
PGND4 21 power ground 4
OUT4+ 22 output 4+
VP4 23 supply voltage 4
handbook, halfpage
TDA8567Q
MGG152
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
VP1
OUT1+
PGND1
OUT1−
OUT2−
PGND2
OUT2+
VP2
VDIAG
IN1
IN2
SGND
IN3
IN4
MODE
VP3
OUT3+
PGND3
OUT3−
OUT4−
PGND4
OUT4+
VP4
Fig.2 Pin configuration.
1998 Sep 23 5
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
FUNCTIONAL DESCRIPTION
The TDA8567Q contains four identical amplifiers which
can be used for bridge applications. The gain of each
amplifier is fixed at 26 dB.
Mode select switch (pin 15)
•Standby: low supply current (<100 µA)
•Mute: input signal suppressed
•Operating: normal on condition.
Since this pin has a low input current (<80 µA), a low cost
supply switch can be applied.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during ≥150 ms (charging of the input
capacitors at pins 10, 11, 13 and 14). When switching
from standby to mute, the slope should be at least 18 V/s.
This can be realized by:
•Microprocessor control
•External timing circuit (see Fig.3).
Diagnostic output (pin 9)
DYNAMIC DISTORTION DETECTOR (DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 9
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and so limit the distortion. The output level of pin 9
is independent of the number of channels that are clipping
(see Fig.4).
SHORT-CIRCUIT DIAGNOSTIC
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
10 ms after removal of the short-circuit. During this
short-circuit condition, pin 9 is continuously LOW.
When a short-circuit occurs across the load of one or more
channels, the output stages are switched off during
approximately 10 ms. After that time it is checked during
approximately 50 µs to determine whether the short-circuit
is still present.
Due to this duty cycle of 50 µs/10 ms the average current
consumption during this short-circuit condition is very low.
During this short-circuit condition, pin 9 is LOW for 10 ms
and HIGH for 50 µs (see Fig.5). The protection circuits of
all channels are coupled. This means that if a short-circuit
condition occurs in one of the channels, all channels are
switched off. Consequently, the power dissipation in any
short-circuit condition is very low.
TEMPERATURE PRE-WARNING
When the virtual junction temperature Tvj reaches 145 °C,
pin 9 goes LOW.
OPEN COLLECTOR OUTPUTS
The diagnostic pin has an open collector output, so more
devices can be tied together. An external pull-up resistor is
needed.
Fig.3 Mode select switch circuitry.
handbook, halfpage
+VP
MODE
MGD959
BZX79C/3.9V
10 kΩ
47 µF
Fig.4 Distortion detector waveform.
handbook, halfpage
V9
0
VP
Vo
0
t
MGG155
1998 Sep 23 6
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
Fig.5 Short-circuit waveform.
handbook, full pagewidth
MGG156
short-circuit over the load
10 ms
50 µs
t
t
VP
short
circuit
current
V9
1998 Sep 23 7
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
THERMAL CHARACTERISTICS
QUALITY SPECIFICATION
In accordance with
“SNW-FQ-611E”
. The number of the quality specification can be found in the
“Quality Reference
Handbook
”. The handbook can be ordered using the code 9397 750 00192.
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
VPsupply voltage operating −18 V
non-operating −30 V
load dump protection;
during 50 ms; tr≥2.5 ms −45 V
Vsc(safe) short-circuit safe voltage −18 V
Vrp reverse polarity voltage −6V
I
OSM non-repetitive peak output current −10 A
IORM repetitive peak output current −7.5 A
Ptot total power dissipation −60 W
Tstg storage temperature −55 +150 °C
Tamb operating ambient temperature −40 +85 °C
Tvj virtual junction temperature −150 °C
SYMBOL PARAMETER VALUE UNIT
Rth j-a thermal resistance from junction to ambient in free air 40 K/W
Rth j-c thermal resistance from junction to case (see Fig.6) 1 K/W
Fig.6 Equivalent thermal resistance network.
handbook, halfpage
3.2 K/W
0.2 K/W
3.2 K/W
3.2 K/W 3.2 K/W
virtual junction
OUT1 OUT2 OUT3 OUT4
case
MGG157
1998 Sep 23 8
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
DC CHARACTERISTICS
VP= 14.4 V; Tamb =25°C; measured in Fig.7; unless otherwise specified.
Notes
1. The circuit is DC adjusted at VP= 6 to 18 V and AC operating at VP= 8.5 to 18 V.
2. At 18V<V
P< 30 V the DC output voltage ≤1⁄2VP.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Supply
VPsupply voltage note 1 6 14.4 18 V
Iq(tot) total quiescent current RL=∞−230 360 mA
Operating condition
V15 mode select switch level 8.5 −VPV
I15 mode select switch current V15 = 14.4 V −30 80 µA
VOoutput voltage note 2 −7.0 −V
∆VOoutput offset voltage −−150 mV
Mute condition
V15 mode select switch level 3.3 −6.4 V
VOoutput voltage note 2 −7.0 −V
∆VOoutput offset voltage −−150 mV
Standby condition
V15 mode select switch level 0 −2V
I
stb standby current −0.2 100 µA
Diagnostic
V9diagnostic output voltage during any fault condition −−0.6 V
Tvj temperature pre-warning V9= 0.6 V −145 −°C
1998 Sep 23 9
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
AC CHARACTERISTICS
VP= 14.4 V; RL=4Ω; f = 1 kHz; Tamb =25°C; measured in Fig.7; unless otherwise specified.
Notes
1. Frequency response externally fixed.
2. Vripple =V
ripple(max) = 2 V (p-p); Rs=0Ω.
3. B = 20 Hz to 20 kHz; Rs=0Ω.
4. B = 20 Hz to 20 kHz; Rs=10kΩ.
5. B = 20 Hz to 20 kHz; independent of Rs.
6. PO= 16 W; Rs=10kΩ.
7. Vi=V
i(max) = 1 V (RMS).
8. Dynamic Distortion Detector (DDD) active, pin 9 is set to logic 0.
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Pooutput power THD = 0.5% 16 19 −W
THD = 10% 21 25 −W
THD = 30% 28 35 −W
VP= 13.2 V; THD = 0.5% −15 −W
VP= 13.2 V; THD = 10% −21 −W
THD total harmonic distortion Po=1W −0.05 −%
V9≤0.6 V; note 8 −10 −%
Bppower bandwidth THD = 0.5%; Po=−1dB
with respect to 16 W −20 to
20000 −Hz
fro(l) low frequency roll-off at −1 dB; note 1 −25 −Hz
fro(h) high frequency roll-off at −1dB 20 −−kHz
Gvclosed loop voltage gain 25 26 27 dB
SVRR supply voltage ripple rejection on; note 2 50 −−dB
mute; note 2 50 −−dB
standby; note 2 80 −−dB
Ziinput impedance 25 30 38 kΩ
Vn(o) noise output voltage on; note 3 −85 120 µV
on; note 4 −100 −µV
mute; note 5 −60 −µV
α
cs channel separation note 6 45 −−dB
∆Gvchannel unbalance −−1dB
V
ooutput signal in mute note 7 −−2mV
1998 Sep 23 10
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
TEST AND APPLICATION INFORMATION
Fig.7 Application circuit diagram.
Special care must be taken in the PCB-layout to separate pin 9 from the pins 10, 11 13 and 14 to minimize the crosstalk between the clip output
and the inputs.
To avoid switch-on plops, it is advised to keep the amplifier in the mute mode during a period of ≥ 150 ms (charging the input capacitors at pin
10, 11, 13 and 14).
handbook, full pagewidth
MGG158
OUT1+
RL = 4 Ω
OUT1−
+
−
+
−
Vref
2
IN1
input 1
IN2
input 2
4
15
10
MODE
2200 µF100 nF
23
+14.4 V
1681
VP1 VP2 VP3 VP4
VP
30 kΩ
OUT2+
RL = 4 Ω
OUT2−
+
−
+
−
7
5
11
30 kΩ
470 nF
470 nF
470 nF
470 nF
211863
PGND1 PGND2 PGND3 PGND4
power ground (substrate)
OUT3+
RL = 4 Ω
OUT3−
+
−
+
−
Vref
17
IN3
SGND
TDA8567Q
input 3
IN4
input 4
19
13
12
30 kΩ
OUT4+
RL = 4 Ω
OUT4−
+
−
+
−
22
20
14
30 kΩ
10 kΩ
VDIAG
+VP
DIAGNOSTIC diagnostic
output
9
1998 Sep 23 11
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
Test information
Figures 8 to 13 have the following conditions: VP= 14.4 V; RL=4Ω; f = 1 kHz; 80 kHz filter used; unless otherwise
specified.
Fig.8 IPas a function of VP.
handbook, halfpage
0
300
200
100
04VP (V)
IP
(mA)
2081216
MGD921
Fig.9 Poas a function of VP.
(1) EIAJ.
(2) 10%.
(3) 0.5%.
handbook, halfpage
818
60
0
(1)
(2)
(3)
20
40
10
Po
(W)
VP (V)
12 14 16
MGD922
Fig.10 THD + N as a function of Po.
handbook, halfpage
10
1
Po (W)
10−1
10−2
MGD923
10 102103104105
THD+N
(%)
1 kHz
f = 10 kHz
100 Hz
Fig.11 THD + N as a function of frequency.
handbook, halfpage
10
1
f (Hz)
10−1
10−2
MGD924
10 102103104105
THD+N
(%)
10 W
1 W
1998 Sep 23 12
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
Fig.12 SVRR as a function of frequency.
handbook, halfpage
−90
−70
−50
−30
MGD925
10 f (Hz)
SVRR
(dB)
102103104105
Fig.13 Channel separation as a function of
frequency.
(1) channel 1 ⇔channel 2, channel 3 ⇔channel 4.
(2) channels 1 and 2 ⇔channels 3 and 4.
handbook, halfpage
−90
−70
−50
−30
MGD926
10
(1)
(2)
f (Hz)
αcs
(dB)
102103104105
1998 Sep 23 13
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
PCB layout
Fig.14 PCB layout (component side).
handbook, full pagewidth
MGK079
Pgnd
2200 µF100 nF
470 nF
10 kΩdiag in
12 34
in mode
out 4
out 3
sgnd
470 nF
out1
out2
VP−
+
−
+
−
+
−
+
−
78.74
111.76
Dimensions in mm.
1998 Sep 23 14
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
Fig.15 PCB layout (soldering side).
handbook, full pagewidth
MGK080
Pgnd
2200 µF
100nF
470 nF
10 kΩ
diagin
1234
inmode
out 4
out 3
sgnd
470 nF
out1
out2
VP
−
+
−
+
−
+
−
+
−
78.74
111.76
Dimensions in mm.
1998 Sep 23 15
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
PACKAGE OUTLINE
UNIT A2
REFERENCES
OUTLINE
VERSION EUROPEAN
PROJECTION ISSUE DATE
IEC JEDEC EIAJ
mm 4.6
4.3
A4
1.15
0.85
A5
1.65
1.35
DIMENSIONS (mm are the original dimensions)
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
SOT411-1 96-10-11
98-02-20
0 5 10 mm
scale
D
L
L1
L2
E2
E
c
A4
A5
A2
m
L3
E1
Q
wM
bp
1
d
Ze
2
e
e
123
j
DBS23P: plastic DIL-bent-SIL power package; 23 leads (straight lead length 3.2 mm) SOT411-1
vM
D
xh
Eh
non-concave
view B: mounting base side
B
β
e1
bpcD
(1) E(1) Z(1)
deD
hLL
3
m
0.75
0.60 0.55
0.35 30.4
29.9 28.0
27.5 12 2.54
12.2
11.8 10.15
9.85
1.27
e2
5.08 2.4
1.6
Eh
6
E1
14.0
13.0
L1
10.7
9.9
L2
6.2
5.8
E2
1.43
0.78
2.1
1.8
1.85
1.65 4.3
3.6
2.8
Qj
0.25
w
0.6
v
0.03
x
45°
β
1998 Sep 23 16
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our
“Data Handbook IC26; Integrated Circuit Packages”
(order code 9398 652 90011).
Soldering by dipping or by wave
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
Repairing soldered joints
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
DEFINITIONS
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
1998 Sep 23 17
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
NOTES
1998 Sep 23 18
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
NOTES
1998 Sep 23 19
Philips Semiconductors Product specification
4×25 W BTL quad car radio power
amplifier TDA8567Q
NOTES
Internet: http://www.semiconductors.philips.com
Philips Semiconductors – a worldwide company
© Philips Electronics N.V. 1998 SCA60
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Pakistan: see Singapore
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Al. Vicente Pinzon, 173, 6th floor,
04547-130 SÃO PAULO, SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 821 2382
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 93 301 6312, Fax. +34 93 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 5985 2000, Fax. +46 8 5985 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2741 Fax. +41 1 488 3263
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors,
International Marketing & Sales Communications, Building BE-p, P.O. Box 218,
5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010,
Fax. +43 160 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Band Box Building, 2nd floor,
254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025,
Tel. +91 22 493 8541, Fax. +91 22 493 0966
Indonesia: PT Philips Development Corporation, Semiconductors Division,
Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510,
Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku,
TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Printed in The Netherlands 545102/750/02/pp20 Date of release: 1998 Sep 23 Document order number: 9397 750 04369
