UDQ2559LB-TTR - Allegro MicroSystems, Inc.

UDx2559B

PROTECTED

QUAD POWER DRIVER

Providing improved output current limiting, the UDK, UDN, and

UDQ2559B, EB, and LB quad power drivers combine AND logic

gates and high-current bipolar outputs with complete output protection.

Each of the four outputs will sink 700 mA in the on state. The outputs

have a minimum breakdown voltage (load dump) of 60 V and a

sustaining voltage of 40 V. The inputs are compatible with TTL and

5 V CMOS logic systems.

Over-current protection for each channel has been designed into

these devices and is activated at approximately 1 A. It protects each

output from short circuits with supply voltages up to 25 V. When an

output current trip point is reached, that output stage is driven linearly

resulting in a reduced output current level. If an over-current or short-

circuit condition continues, the thermal-limiting circuits will first sense

the rise in junction temperature and then the rise in chip temperature,

further decreasing the output current. Under worst-case conditions,

these devices will tolerate short circuits on all outputs, simultaneously.

These devices can be used to drive various loads including incan-

descent lamps (without warming or limiting resistors) or inductive

loads such as relays, solenoids, or dc stepping motors.

The packages offer fused leads for enhanced thermal dissipation.

Package B is a 16-pin power DIP with exposed tabs, EB is a 28-lead

power PLCC, and LB is a 16-lead power wide-body SOIC for surface-

mount applications. The lead (Pb) free versions have 100% matte tin

leadframe plating.

FEATURES

■ 700 mA Output Current per Channel

■ Independent Over-Current Protection for Each Driver

■ Thermal Protection for Device and Each Driver

■ Low Output-Saturation Voltage

■ Integral Output Flyback Diodes

■ TTL and 5 V CMOS Compatible Inputs

ABSOLUTE MAXIMUM RATINGS

at TA = 25°C

Output Voltage, VOUT . . . . . . . . . 60 V

Over-Current Protected Output Voltage,

VOUT . . . . . . . . . . . . . . . . . . . 25 V

Output Current, IOUT . . . . . . . . . 1.0 A*

Supply Voltage, VCC . . . . . . . . . . 7.0 V

Input Voltage, VIN or VEN . . . . . . 7.0 V

Package Power Dissipation,

PD . . . . . . . . . . . . . . . . See Graph

Operating Temperature Range, TA

Prefix ‘UDK’ . . . . -40°C to +125°C

Prefix ‘UDN’ . . . . . -20°C to +85°C

Prefix ‘UDQ’ . . . . . -40°C to +85°C

Storage Temperature Range,

TS . . . . . . . . . . . . -55°C to +150°C

*Outputs are peak current limited at

approximately 1.0 A per driver. See

Circuit Description and Application for

further information.

2559

314

ENABLE

GROUND

OUT2

GROUND

OUT3

OUT4

OUT1

VCC

IN 1

Dwg. PP-017-1

IN4

IN3

IN 2

2559

PROTECTED

QUAD POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000

Selection Guide

Part Number Pb-free Package Ambient Temperature

(°C)

UDN2559B – 16-pin DIP, exposed tabs

UDN2559B-T Yes 16-pin DIP, exposed tabs

UDN2559EB – 28-lead PLCC –20 to 85

UDN2559EB-T Yes 16-pin DIP, exposed tabs

UDN2559LB Yes 16-lead SOIC

UDN2559LB-T Yes 16-lead SOIC

UDQ2559B – 16-pin DIP, exposed tabs

UDQ2559B-T Yes 16-pin DIP, exposed tabs –40 to 85

UDQ2559LB – 16-lead SOIC

UDQ2559LB-T Yes 16-lead SOIC

UDK2559B – 16-pin DIP, exposed tabs

UDK2559B-T Yes 16-pin DIP, exposed tabs

UDK2559EB – 28-lead PLCC –40 to 125

UDK2559EB-T Yes 28-lead PLCC

UDK2559LB – 16-lead SOIC

UDK2559LB-T Yes 16-pin DIP, exposed tabs

UDx2559LB

314

ENABLE

GROUND

OUT

GROUND

OUT

Dwg. PP-017-6

2559

PROTECTED

QUAD POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000

FUNCTIONAL BLOCK DIAGRAM

(1 of 4 Channels)

UDx2559EB

50 75 100 125 150

ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS

TEMPERATURE IN °°

°°C

R = 6°C/W

θJT

Dwg. GP-004-2B

SUFFIX 'EB', R = 36°C/W

θJA

SUFFIX 'B', R = 43°C/W

θJA

SUFFIX 'LB', R = 90°C/W

θJA

PD = (VOUT1 x IOUT1 x dc) + … + (VOUTn x IOUTn x dc)

+ (VCC x ICC) = (TJ - TA)/RθJA

VCC

<<1 Ω

OUT

Dwg. FP-041

IN N

THERMAL

LIMIT

ENABLE

18 26

GROUND

GROUND GROUND

GROUND

Dwg. PP-019-1

CONNECTION

ENABLE

SUPPLY

OUT

CONNECTION

255

2559

PROTECTED

QUAD POWER DRIVER

www.allegromicro.com

ELECTRICAL CHARACTERISTICS at TA = +25°C (prefix ‘UDN’) or over operating

temperature range (prefix ‘UDK’ or ‘UDQ’), VCC = 4.75 V to 5.25 V

Limits

Characteristic Symbol Test Conditions Min. Typ. Max. Units

Output Leakage Current ICEX VOUT = 50 V, VIN = 0.8 V, VEN = 2.0 V —<1.0 100 µA

VOUT = 50 V, VIN = 2.0 V, VEN = 0.8 V —<1.0 100 µA

Output Sustaining Voltage VOUT(SUS) IOUT = 100 mA, VIN = VEN = 0.8 V 40 —— V

Output Saturation Voltage VOUT(SAT) All Devices, IOUT = 100 mA ——300 mV

All Devices, IOUT = 400 mA ——500 mV

‘B’ & ‘EB’ Packages Only, IOUT = 600 mA ——700 mV

Over-Current Trip ITRIP —1.0 —A

Input Voltage Logic 1 VIN(1) or VEN(1) 2.0 —— V

Logic 0 VIN(0) or VEN(0) ——0.8 V

Input Current Logic 1 VIN(1) or VEN(1) = 2.0 V ——40 µA

Logic 0 VIN(0) or VEN(0) = 0.8 V ——-10 µA

Total Supply Current ICC All Outputs ON, VIN* = VEN = 2.0 V ——80 mA

All Outputs OFF ——5.0 mA

Clamp Diode Forward Voltage VFIF = 1.0 A ——1.7 V

IF = 1.5 A ——2.1 V

Clamp Diode Leakage Current IRVR = 50 V, D1 + D2 or D3 + D4——50 µA

Turn-On Delay tPHL IOUT = 500 mA ——20 µs

tPLH IOUT = 500 mA ——20 µs

Thermal Limit TJ—165 —°C

Typical Data is for design information only.

Negative current is defined as coming out of (sourcing) the specified terminal.

As used here, -100 is defined as greater than +10 (absolute magnitude convention) and the minimum is implicitly zero.

* All inputs simultaneously, all other tests are performed with each input tested separately.

2559

PROTECTED

QUAD POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000

TYPICAL OUTPUT

CHARACTERISTIC

CIRCUIT DESCRIPTION AND APPLICATION

INCANDESCENT LAMP DRIVER

High incandescent lamp turn-ON/in-rush currents can contribute to

poor lamp reliability and destroy semiconductor lamp drivers. Warm-

ing or current-limiting resistors protect both driver and lamp but use

significant power either when the lamp is OFF or when the lamp is

ON, respectively. Lamps with steady-state current ratings up to 700

mA can be driven by these devices without the need for warming

(parallel) or current-limiting (series) resistors.

When an incandescent lamp is initially turned ON, the cold fila-

ment is at minimum resistance and would normally allow a 10x to 12x

in-rush current. With these drivers, during turn-ON, the high in-rush

current is sensed by the internal low-value sense resistor. Drive current

to the output stage is then diverted by the shunting transistor, and the

load current is momentarily limited to approximately 1.0 A. During

this short transition period, the output current is reduced to a value

dependent on supply voltage and filament resistance. During lamp

warmup, the filament resistance increases to its maximum value, the

output stage goes into saturation and applies maximum rated voltage to

the lamp.

INDUCTIVE LOAD DRIVER

Bifilar (unipolar) stepper motors, relays, or solenoids can be driven

directly. The internal flyback diodes prevent damage to the output transistors

by suppressing the high-voltage spikes that occur when turning OFF an

inductive load.

For rapid current decay (fast turn-OFF speeds), the use of Zener diodes

will raise the flyback voltage and inprove performance. However, the peak

voltage must not exceed the specified minimum sustaining voltage (VSUPPLY +

VZ + VF ≤ VOUT(SUS)).

FAULT CONDITIONS

In the event of a shorted load, the load current will attempt to

increase. As described above, the drive current to the affected output

stage is reduced, causing the output stage to go linear, limiting the peak

output current to approximately 1 A. As the power dissipation of that

output stage increases, a thermal gradient sensing circuit will become

operational, further decreasing the drive current to the affected output

stage and reducing the output current to a value dependent on supply

voltage and load resistance.

Continuous or multiple overload conditions causing the chip

temperature to reach approximately 165°C will result in an additional

reduction in output current to maintain a safe level.

If the fault condition is corrected, the output stage will return to its

normal saturated condition.

TYPICAL OUTPUT BEHAVIOR

OUT(SAT)

Dwg. GP-013

OUTPUT VOLTAGE, V

OUT

OUTPUT CURRENT, I

OUT

T < 150°C

T = 165°C

JUNCTION

TEMP. LIMIT

NOT TO SCALE

TRIP

THERMAL

GRADIENT

SENSING

NORMAL LAMP IN-RUSH CURRENT

TIME

THERMAL GRADIENT SENSING

CURRENT LIMIT

Dwg. WP-008

NOT TO SCALE

TRIP

LAMP CURRENT

2559

PROTECTED

QUAD POWER DRIVER

.070

.045 1.78

1.14

.150

.115 3.81

2.92

.195

.115 4.95

2.92

.014

.008 0.36

0.20

.430

MAX 10.92

.015

MIN 0.38

.005

MIN 0.13

.280

.240 7.11

6.10

.775

.735 19.69

18.67 AB

SEATING

PLANE

.022

.014 .056

.036

16X

.010 [0.25] M C

.100 .2.54

.300 .7.62

.210

MAX 5.33

Preliminary dimensions, for reference only

Dimensions in inches

Metric dimensions (mm) in brackets, for reference only

(reference JEDEC MS-001 BB)

Dimensions exclusive of mold flash, gate burrs, and dambar protrusions

Exact case and lead configuration at supplier discretion within limits shown

ATerminal #1 mark area

B Package, 16-pin DIP

with internally fused pins 4, 5, 12, and 13

and external thermal tabs

2559

PROTECTED

QUAD POWER DRIVER

www.allegromicro.com

EB Package, 28-pin PLCC

with internally fused pins 5 through 11 and 19 through 25

2128

ATerminal #1 mark area

Preliminary dimensions, for reference only

(reference JEDEC MS-018 AB)

Dimensions in inches

Millimeters (mm) in brackets, for reference only

Dimensions exclusive of mold flash, gate burrs, and dambar protrusions

Exact case and lead configuration at supplier discretion within limits shown

.120

.090

3.05

2.29

.180

.165

4.57

4.19

11.58

11.43

.456

.450

5.56

4.85

.219

.191

5.56

4.85

.219

.191

5.56

4.85

.219

.191

5.56

4.85

.219

.191

.020

MIN

0.51

SEATING

PLANE

.032

.026

0.81

0.66

28X

C.004 [0.10]

28X

.007 [0.18] H B A

12.57

12.32

.495

.485

.007 [0.18] H B

12.57

12.32

.495

.485

.007 [0.18] H B

B.002 [0.05]

.050 1.27

.020 0.51

11.58

11.43

.456

.450

.007 [0.18] H B

B.002 [0.05]

.007 [0.18] C B

.021

.013

0.53

0.33

28X

.007 [0.18] C B

2559

PROTECTED

QUAD POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000

LB Package, 16-pin SOIC

with internally fused pins 4 and 5, and 12 and 13

0.30

0.10

.012

.004

2.65

2.35

.104

.093

7.60

7.40

.299

.291

0.33

0.20

.013

.008

8º

0º

1.27

0.40

.050

.016

10.50

10.10

.614

.598

SEATING

PLANE

C0.10 [.004]

16X

0.25 .010

0.51

0.31

.020

.012

16X

0.25 [.010] M C A B

10.63

9.97

.419

.393

0.25 [.010] M B M

1.27 .050

GAUGE PLANE

SEATING PLANE

Preliminary dimensions, for reference only

Dimensions in millimeters

U.S. Customary dimensions (in.) in brackets, for reference only

(reference JEDEC MS-013 AA)

Dimensions exclusive of mold flash, gate burrs, and dambar protrusions

Exact case and lead configuration at supplier discretion within limits shown

ATerminal #1 mark area

2559

PROTECTED

QUAD POWER DRIVER

115 Northeast Cutoff, Box 15036

Worcester, Massachusetts 01615-0036 (508) 853-5000

The products described here are manufactured under one or more

U.S. patents or U.S. patents pending.

Allegro MicroSystems, Inc. reserves the right to make, from time to

time, such departures from the detail specifications as may be

required to permit improvements in the performance, reliability, or

manufacturability of its products. Before placing an order, the user is

cautioned to verify that the information being relied upon is current.

Allegro products are not authorized for use as critical components

in life-support devices or systems without express written approval.

The information included herein is believed to be accurate and

reliable. However, Allegro MicroSystems, Inc. assumes no responsi-

bility for its use; nor for any infringement of patents or other rights of

third parties which may result from its use.