Product Folder Order Now Technical Documents Support & Community Tools & Software LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 LM2574x SIMPLE SWITCHER(R) 0.5-A Step-Down Voltage Regulator 1 Features 3 Description * The LM2574xx series of regulators are monolithic integrated circuits that provide all the active functions for a step-down (buck) switching regulator, capable of driving a 0.5-A load with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, 15 V, and an adjustable output version. 1 * * * * * * * * * * * New product available: TPS560430, 36-V, 600mA synchronous step-down converter 3.3-V, 5-V, 12-V, 15-V, and adjustable output versions Adjustable version output voltage range: 1.23 V to 37 V (57 V for HV version) 4% maximum over line and load conditions Specified 0.5-A output current Wide input voltage range: 40 V, up to 60 V for HV Version Requires only four external components 52-kHz Fixed-frequency internal oscillator TTL shutdown capability, low-power standby mode High efficiency Uses readily available standard inductors Thermal shutdown and current-limit protection Create a custom design using the LM2574 with the WEBENCH(R) Power Designer 2 Applications * * * * Simple high-efficiency step-down (buck) regulator Efficient preregulator for linear regulators On-card switching regulators Positive-to-negative converter (buck-boost) Requiring a minimum number of external components, these regulators are simple to use and include internal frequency compensation and a fixedfrequency oscillator. The LM2574xx series offers a high-efficiency replacement for popular three-terminal linear regulators. Because of its high efficiency, the copper traces on the printed-circuit board (PCB) are normally the only heat sinking needed. A standard series of inductors optimized for use with the LM2574 are available from several different manufacturers. This feature greatly simplifies the design of switch-mode power supplies. Other features include a specified 4% tolerance on output voltage within specified input voltages and output load conditions, and 10% on the oscillator frequency. External shutdown is included, featuring 50-A (typical) standby current. The output switch includes cycle-by-cycle current limiting, as well as thermal shutdown for full protection under fault conditions. The TPS560430 is a newer generation buck converter, being functionally equivalent to LM2574. It offers reduced BOM cost, increased efficiency, and reduced solution size. See the Device Comparison Table to compare specifications. Start WEBENCH Design with TPS560430. Device Information(1) PART NUMBER LM2574, LM2574HV PACKAGE BODY SIZE (NOM) SOIC (14) 8.992 mm x 7.498 mm PDIP (8) 6.35 mm x 9.81 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Typical Application (Fixed Output Voltage Versions) 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 4 6.1 6.2 6.3 6.4 6.5 4 4 4 4 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics for All Output Voltage Versions ..................................................................... 6.6 Electrical Characteristics - 3.3-V Version................. 6.7 Electrical Characteristics - 5-V Version.................... 6.8 Electrical Characteristics - 12-V Version.................. 6.9 Electrical Characteristics - 15-V Version.................. 6.10 Electrical Characteristics - Adjustable Version....... 6.11 Typical Characteristics ............................................ 7 5 5 6 6 6 7 8 Detailed Description ............................................ 11 7.1 Overview ................................................................. 11 7.2 Functional Block Diagram ....................................... 11 7.3 Feature Description................................................. 11 7.4 Device Functional Modes........................................ 13 8 Application and Implementation ........................ 14 8.1 Application Information............................................ 14 8.2 Typical Applications ................................................ 19 9 Power Supply Recommendations...................... 26 10 Layout................................................................... 26 10.1 10.2 10.3 10.4 Layout Guidelines ................................................. Layout Example .................................................... Grounding ............................................................. Thermal Considerations ........................................ 26 27 27 27 11 Device and Documentation Support ................. 29 11.1 11.2 11.3 11.4 11.5 11.6 11.7 Device Support...................................................... Documentation Support ........................................ Receiving Notification of Documentation Updates Support Resources ............................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 29 31 31 31 31 31 31 12 Mechanical, Packaging, and Orderable Information ........................................................... 31 4 Revision History Changes from Revision E (July 2018) to Revision F * Page Added verbiage for TPS560430 ............................................................................................................................................. 1 Changes from Revision D (April 2016) to Revision E Page * Added links for WEBENCH ................................................................................................................................................... 1 * maximum supply voltage in Abs Max Ratings from "4.5" to "45" to correct typo ................................................................... 4 Changes from Revision C (April 2013) to Revision D Page * Added Device Information table, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ..................................... 1 * Changed RJA value in SOIC column to 77.1 ........................................................................................................................ 4 * Split test conditions row of the Electrical Characteristics table to include TJ = 25C and TJ < 25C MIN, TYP, and MAX values............................................................................................................................................................................. 5 * Split test conditions in IL row to rearrange the MIN, TYP, and MAX values ......................................................................... 5 Changes from Revision B (November 2004) to Revision C * 2 Page Changed layout of National Data Sheet to TI format ............................................................................................................. 1 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 5 Pin Configuration and Functions P Package 8-Pin PDIP Top View NPA Package 14-Pin SOIC Top View FB 1 8 NC SIG_GND 2 7 OUTPUT ON/OFF 3 6 NC PWR_GND 4 5 V IN NC 1 14 NC NC 2 13 NC FB 3 12 OUTPUT SIG_GND 4 11 NC ON/OFF 5 10 V PWR_GND 6 9 NC NC 7 8 NC IN Pin Functions PIN NAME I/O DESCRIPTION PDIP SOIC FB 1 3 I NC 8, 6 1, 2, 7, 8, 9, 11, 13, 14 -- No internal connection, but must be soldered to PCB for best heat transfer. ON/OFF 3 5 I Enable input to the voltage regulator. High = OFF and low = ON. Connect to GND to enable the voltage regulator. Do not leave this pin float. OUTPUT 7 12 O Emitter pin of the power transistor. This is a switching node. Attached this pin to an inductor and the cathode of the external diode. PWR_GND 4 6 -- Power ground pins. Connect to system ground and SIF GND, ground pins of CIN and COUT. Path to CIN must be as short as possible. SIG_GND 2 4 -- Signal ground pin. Ground reference for internal references and logic. Connect to system ground. VIN 5 10 I Feedback sense input pin. Connect to the midpoint of feedback divider to set VOUT for ADJ version or connect this pin directly to the output capacitor for a fixed output version. Supply input pin to collector pin of high-side transistor. Connect to power supply and input bypass capacitors CIN. Path from VIN pin to high frequency bypass CIN and PWR GND must be as short as possible. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 3 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN Maximum supply voltage MAX LM2574 45 LM2574HV 63 ON/OFF pin input voltage -0.3 Output voltage to ground, steady-state Power dissipation UNIT V VIN V -1 V Internally limited Lead temperature, soldering (10 s) 260 C Maximum junction temperature 150 C 150 C Storage temperature, Tstg (1) -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 6.2 ESD Ratings V(ESD) (1) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 VALUE UNIT 2000 V (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN Supply voltage TJ NOM LM2574 40 LM2574HV 60 Temperature MAX -40 UNIT V 125 C 6.4 Thermal Information LM2574, LM2574HV THERMAL METRIC RJA (1) (2) Junction-to-ambient thermal resistance (3) RJC(top) Junction-to-case (top) thermal resistance (3) (3) P (PDIP) NPA (SOIC) 8 PINS 14 PINS UNIT 60.4 77.1 C/W 59.9 29.2 C/W RJB Junction-to-board thermal resistance 37.9 33.3 C/W JT Junction-to-top characterization parameter 17.1 2 C/W JB Junction-to-board characterization parameter 37.7 32.8 C/W -- -- C/W RJC(bot) Junction-to-case (bottom) thermal resistance (1) (2) (3) 4 (3) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report. The package thermal impedance is calculated in accordance with JESD 51-7. Thermal resistances were simulated on a 4-layer, JEDEC board. Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 6.5 Electrical Characteristics for All Output Voltage Versions TJ = 25C, and MIN and MAX apply over full operating temperature range. VIN = 12 V for the 3.3-V, 5-V, and adjustable version, VIN = 25 V for the 12-V version, and VIN = 30 V for the 15-V version, ILOAD = 100 mA (unless otherwise noted). PARAMETER TEST CONDITIONS Ib Feedback bias current Adjustable version only, VOUT = 5 V fO Oscillator frequency See (2) VSAT Saturation voltage IOUT = 0.5 A (3) DC Maximum duty cycle (ON) See (4) Current limit IL Current output leakage IQ Quiescent current See (5) ISTBY Standby quiescent current ON/OFF pin = 5 V (OFF) TYP MAX (1) 50 100 TJ = 25C -40C < TJ < 125C 500 TJ = 25C 47 -40C < TJ < 125C 42 TJ = 25C 52 58 63 0.9 -40C < TJ < 125C Peak current (2) (3) ICL MIN (1) 1.2 1.4 93% 98% 0.7 1 0.65 1.6 1.8 Output = 0 V 2 Output = -1 V (5) (6) 7.5 30 UNIT nA kHz V A mA 5 10 mA 50 200 A ON/OFF CONTROL (SEE Figure 27) VIH VOUT = 0 V ON/OFF pin logic input level VOUT = Nominal output voltage VIL IH ON/OFF pin input current IIL (1) (2) (3) (4) (5) (6) TJ = 25C 2.2 -40C < TJ < 125C 2.4 TJ = 25C 1.4 1.2 -40C < TJ < 125C V 1 0.8 V ON/OFF pin = 5 V (OFF) 12 30 A ON/OFF pin = 0 V (ON) 0 10 A All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. The oscillator frequency reduces to approximately 18 kHz in the event of an output short or an overload which causes the regulated output voltage to drop approximately 40% from the nominal output voltage. This self protection feature lowers the average power dissipation of the IC by lowering the minimum duty cycle from 5% down to approximately 2% (see Figure 6). Output pin sourcing current. No diode, inductor or capacitor connected to output pin. Feedback pin removed from output and connected to 0 V. Feedback pin removed from output and connected to 12 V for the adjustable, 3.3-V, and 5-V versions, and 25 V for the 12-V and 15-V versions, to force the output transistor OFF. VIN = 40 V (60 V for high voltage version). 6.6 Electrical Characteristics - 3.3-V Version TJ = 25C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted). PARAMETER (1) TEST CONDITIONS VIN = 12 V, ILOAD = 100 mA VOUT (1) (2) Output voltage Efficiency MIN (2) TYP MAX (2) 3.234 3.3 3.366 LM2574, 4.75 V VIN 40 V, 0.1 A ILOAD 0.5 A TJ = 25C 3.168 3.3 3.432 -40C TJ 125C 3.135 LM2574HV, 4.75 V VIN 60 V, 0.1 A ILOAD 0.5 A TJ = 25C 3.168 -40C TJ 125C 3.135 VIN = 12 V, ILOAD = 0.5 A 3.465 3.3 UNIT V 3.45 3.482 72% Test Circuit in Figure 22 and Figure 27. All limits specified at room temperature and at temperature extremes . All room temperature limits are 100% production tested. All limits at temperature extremes are specified via correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 5 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 6.7 Electrical Characteristics - 5-V Version TJ = 25C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted). PARAMETER (1) MIN TYP (2) TEST CONDITIONS VIN = 12 V, ILOAD = 100 mA VOUT Efficiency (1) (2) Output voltage LM2574, 7 V VIN 40 V, 0.1 A ILOAD 0.5 A TJ = 25C LM2574HV, 7 V VIN 60 V, 0.1 A ILOAD 0.5 A TJ = 25C -40C TJ 125C 4.9 5 4.8 5 4.75 -40C TJ 125C 5 4.75 UNIT 5.1 5.2 5.25 4.8 VIN = 12 V, ILOAD = 0.5 A MAX (2) V 5.225 5.275 77% Test circuit in Figure 22 and Figure 27. All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. 6.8 Electrical Characteristics - 12-V Version TJ = 25C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted). PARAMETER (1) MIN TYP (2) CONDITIONS VIN = 25 V, ILOAD = 100 mA VOUT Output voltage Efficiency (1) (2) LM2574, 15 V VIN 40 V, 0.1 A ILOAD 0.5 A TJ = 25C LM2574HV, 15 V VIN 60 V, 0.1 A ILOAD 0.5 A TJ = 25C -40C TJ 125C 11.76 12 12.24 11.52 12 12.48 11.4 12.6 11.52 -40C TJ 125C MAX (2) 12 11.4 VIN = 15 V, ILOAD = 0.5 A UNIT V 12.54 12.66 88% Test circuit in Figure 22 and Figure 27. All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. 6.9 Electrical Characteristics - 15-V Version TJ = 25C, and all MIN and MAX apply over full operating temperature range (unless otherwise noted). PARAMETER (1) TEST CONDITIONS VIN = 30 V, ILOAD = 100 mA VOUT (1) (2) 6 Output voltage Efficiency LM2574, 18 V VIN 40 V, 0.1A ILOAD 0.5 A TJ = 25C LM2574HV, 18 V VIN 60 V, 0.1 A ILOAD 0.5 A TJ = 25C -40C TJ 125C MIN TYP (2) MAX (2) 14.7 15 15.3 14.4 15 14.25 14.4 -40C TJ 125C VIN = 18 V, ILOAD = 0.5 A 15.6 15.75 15 14.25 UNIT V 15.68 15.83 88% Test circuit in Figure 22 and Figure 27. All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 6.10 Electrical Characteristics - Adjustable Version TJ = 25C, and all MIN and MAX apply over full operating temperature range. VIN = 12 V, ILOAD = 100 mA (unless otherwise noted). PARAMETER (1) TEST CONDITIONS VIN = 12 V, ILOAD = 100 mA VFB (1) (2) Feedback voltage Efficiency LM2574, 7 V VIN 40 V, 0.1 A ILOAD 0.5 A, VOUT programmed for 5 V TJ = 25C LM2574HV, 7 V VIN 60 V, 0.1 A ILOAD 0.5 A, VOUT programmed for 5 V TJ = 25C -40C TJ 125C -40C TJ 125C VIN = 12 V, VOUT = 5 V, ILOAD = 0.5 A MIN TYP (2) MAX (2) 1.217 1.23 1.243 1.193 1.23 1.267 1.18 1.193 UNIT 1.28 1.23 1.18 V 1.273 1.286 77% Test circuit in Figure 22 and Figure 27. All limits specified at room temperature TYP and MAX. All room temperature limits are 100% production tested. All limits at temperature extremes are specified through correlation using standard Statistical Quality Control (SQC) methods. All limits are used to calculate Average Outgoing Quality Level. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 7 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 6.11 Typical Characteristics See Figure 27. 8 Figure 1. Normalized Output Voltage Figure 2. Line Regulation Figure 3. Dropout Voltage Figure 4. Current Limit Figure 5. Supply Current Figure 6. Standby Quiescent Current Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 Typical Characteristics (continued) See Figure 27. Figure 7. Oscillator Frequency Figure 8. Switch Saturation Voltage Figure 9. Efficiency Figure 10. Minimum Operating Voltage Figure 11. Supply Current versus Duty Cycle Figure 12. Feedback Voltage versus Duty Cycle Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 9 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Typical Characteristics (continued) See Figure 27. Figure 13. Feedback Pin Current 10 Submit Documentation Feedback Figure 14. Junction-to-Ambient Thermal Resistance Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 7 Detailed Description 7.1 Overview The LM2574 SIMPLE SWITCHER(R) regulator is an easy-to-use, non-synchronous, step-down DC-DC converter with a wide input voltage range from 40 V to up to 60 V for a HV version. It is capable of delivering up to 0.5-A DC load current with excellent line and load regulation. These devices are available in fixed output voltages of 3.3 V, 5 V, 12 V, 15 V, and an adjustable output version. The family requires few external components and the pin arrangement was designed for simple, optimum PCB layout. 7.2 Functional Block Diagram VIN Unregulated DC Input + CIN ON / OFF Internal Regulator 5 ON / OFF 3 1 Feedback Fixed Gain Error Amp R2 + R1 0.5 Amp Switch Compatator + DRIVER Signal GND Output L1 7 2 1.23 V BAND GAP REFRENCE D1 52 kHz OSCILLATOR Reset Thermal Shutdown Current Limit VOUT + COUT 4 L O A D Pwr Gnd Note: Pin numbers are for the 8-pin PDIP package R1 = 1 k 3.3 V, R2 = 1.7 k 5 V, R2 = 3.1 k 12 V, R2 = 8.84 k 15 V, R2 = 11.3 k For adjustable version, R1 = Open, R2 = 0 7.3 Feature Description 7.3.1 Current Limit The LM2574 device has current limiting to prevent the switch current from exceeding safe values during an accidental overload on the output. This value (ICL) can be found in the Electrical Characteristics for All Output Voltage Versions. 7.3.2 Undervoltage Lockout In some applications, it is desirable to keep the regulator off until the input voltage reaches a certain threshold. An undervoltage lockout circuit that accomplishes this task is shown in Figure 15 while Figure 16 shows the same circuit applied to a buck-boost configuration. These circuits keep the regulator off until the input voltage reaches a predetermined level in Equation 1. VTH VZ1 + 2 VBE (1) Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 11 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Feature Description (continued) Note: Complete circuit not shown (see Figure 20). Note: Pin numbers are for 8-pin PDIP package. Figure 15. Undervoltage Lockout for Buck Circuit Note: Complete circuit not shown (see Figure 20). Note: Pin numbers are for 8-pin PDIP package. Figure 16. Undervoltage Lockout for Buck-Boost Circuit 7.3.3 Delayed Start-up The ON/OFF pin can be used to provide a delayed start-up feature as shown in Figure 17. With an input voltage of 20 V and for the part values shown, the circuit provides approximately 10 ms of delay time before the circuit begins switching. Increasing the RC time constant can provide longer delay times, but excessively large RC time constants can cause problems with input voltages that are high in 60-Hz or 120-Hz ripple, by coupling the ripple into the ON/OFF pin. 7.3.4 Adjustable Output, Low-Ripple Power Supply A 500-mA power supply that features an adjustable output voltage is shown in Figure 18. An additional L-C filter that reduces the output ripple by a factor of 10 or more is included in this circuit. 12 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 Feature Description (continued) Note: Complete circuit not shown. Note: Pin numbers are for 8-pin PDIP package. Figure 17. Delayed Start-up Note: Pin numbers are for 8-pin PDIP package. Figure 18. 1.2-V to 55-V Adjustable 500-mA Power Supply With Low-Output Ripple 7.4 Device Functional Modes 7.4.1 Shutdown Mode The ON/OFF pin provides electrical ON and OFF control for the LM2574. When the voltage of this pin is higher than 1.4 V, the device is shutdown mode. The typical standby current in this mode is 50 A. 7.4.2 Active Mode When the voltage of the ON/OFF pin is below 1.2 V, the device starts switching and the output voltage rises until it reaches a normal regulation voltage. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 13 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information 8.1.1 Input Capacitor (CIN) To maintain stability, the regulator input pin must be bypassed with at least a 22-F electrolytic capacitor. The leads of the capacitor must be kept short, and located near the regulator. If the operating temperature range includes temperatures below -25C, the input capacitor value may need to be larger. With most electrolytic capacitors, the capacitance value decreases and the ESR increases with lower temperatures and age. Paralleling a ceramic or solid tantalum capacitor increases the regulator stability at cold temperatures. For maximum capacitor operating lifetime, the RMS ripple current rating of the capacitor must be greater than Equation 2. t 1.2 ON ILOAD T where * * t ON VOUT = T VIN for a buck regulator VOUT t ON = T VOUT + VIN for a buck-boost regulator (2) 8.1.2 Inductor Selection All switching regulators have two basic modes of operation: continuous and discontinuous. The difference between the two types relates to the inductor current, whether it is flowing continuously, or if it drops to zero for a period of time in the normal switching cycle. Each mode has distinctively different operating characteristics, which can affect the regulator performance and requirements. The LM2574 (or any of the SIMPLE SWITCHER family) can be used for both continuous and discontinuous modes of operation. In many cases, the preferred mode of operation is in the continuous mode. It offers better load regulation, lower peak switch, inductor, and diode currents, and can have lower output ripple voltage. It does require relatively large inductor values to keep the inductor current flowing continuously, especially at low output load currents. To simplify the inductor selection process, an inductor selection guide (nomograph) was designed. This guide assumes continuous mode operation, and selects an inductor that allows a peak-to-peak inductor ripple current (IIND) to be a certain percentage of the maximum design load current. In the LM2574 SIMPLE SWITCHER, the peak-to-peak inductor ripple current percentage (of load current) is allowed to change as different design load currents are selected. By allowing the percentage of inductor ripple current to increase for lower current applications, the inductor size and value can be kept relatively low. 8.1.3 Inductor Ripple Current When the switcher is operating in the continuous mode, the inductor current waveform ranges from a triangular to a sawtooth type of waveform (depending on the input voltage). For a given input voltage and output voltage, the peak-to-peak amplitude of this inductor current waveform remains constant. As the load current rises or falls, the entire sawtooth current waveform also rises or falls. The average DC value of this waveform is equal to the DC load current (in the buck regulator configuration). 14 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 Application Information (continued) If the load current drops to a low enough level, the bottom of the sawtooth current waveform reaches zero, and the switcher changes to a discontinuous mode of operation. This is a perfectly acceptable mode of operation. Any buck switching regulator (no matter how large the inductor value is) is forced to run discontinuous if the load current is light enough. The curve shown in Figure 19 illustrates how the peak-to-peak inductor ripple current (IIND) is allowed to change as different maximum load currents are selected, and also how it changes as the operating point varies from the upper border to the lower border within an inductance region (see the Inductor Selection section). Figure 19. Inductor Ripple Current (iIND) Range Consider the following example: VOUT = 5 V at 0.4 A VIN = 10-V minimum up to 20-V maximum The selection guide in Figure 24 shows that for a 0.4-A load current, and an input voltage range between 10 V and 20 V, the inductance region selected by the guide is 330 H. This value of inductance allows a peak-to-peak inductor ripple current (IIND) to flow that is a percentage of the maximum load current. For this inductor value, the IIND also varies depending on the input voltage. As the input voltage increases to 20 V, it approaches the upper border of the inductance region, and the inductor ripple current increases. Referring to the curve in Figure 19, it can be seen that at the 0.4-A load current level, and operating near the upper border of the 330-H inductance region, the IIND is 53% of 0.4 A, or 212 mAp-p. This IIND is important because from this number the peak inductor current rating can be determined, the minimum load current required before the circuit goes to discontinuous operation, and also, knowing the ESR of the output capacitor, the output ripple voltage can be calculated, or conversely, measuring the output ripple voltage and knowing the IIND, the ESR can be calculated. From the previous example, the peak-to-peak inductor ripple current (IIND) = 212 mAp-p. When the IND value is known, the following three formulas can be used to calculate additional information about the switching regulator circuit: 1. Peak inductor or peak switch current in Equation 3. DI 212 o ae o ae = c ILOAD + IND / = c 0.4 A + = 506 mA 2 2 /o e o e (3) 2. Minimum load current before the circuit becomes discontinuous in Equation 4. DI 212 = IND = = 106 mA 2 2 3. Output ripple voltage = (IIND) x (ESR of COUT) Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback (4) 15 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Application Information (continued) The selection guide chooses inductor values suitable for continuous mode operation, but if the inductor value chosen is prohibitively high, the designer must investigate the possibility of discontinuous operation. Inductors are available in different styles such as pot core, toroid, E-frame, bobbin core, and so forth, as well as different core materials, such as ferrites and powdered iron. The least expensive, the bobbin core type, consists of wire wrapped on a ferrite rod core. This type of construction makes for an inexpensive inductor, but because the magnetic flux is not completely contained within the core, it generates more electro-magnetic interference (EMI). This EMl can cause problems in sensitive circuits, or can give incorrect scope readings because of induced voltages in the scope probe. The inductors listed in the selection chart include powdered iron toroid for Pulse Engineering and ferrite bobbin core for Renco. An inductor must not be operated beyond its maximum rated current because it can saturate. When an inductor begins to saturate, the inductance decreases rapidly and the inductor begins to look mainly resistive (the DC resistance of the winding). This can cause the inductor current to rise very rapidly and affects the energy storage capabilities of the inductor and can cause inductor overheating. Different inductor types have different saturation characteristics, and consider this when selecting an inductor. The inductor manufacturers' data sheets include current and energy limits to avoid inductor saturation. 8.1.4 Output Capacitor An output capacitor is required to filter the output voltage and is needed for loop stability. The capacitor must be located near the LM2574 using short PCB traces. Standard aluminum electrolytics are usually adequate, but low ESR types are recommended for low output ripple voltage and good stability. The ESR of a capacitor depends on many factors, some which are: * The value * The voltage rating * The physical size * The type of construction In general, low-value or low-voltage (less than 12 V) electrolytic capacitors usually have higher ESR numbers. The amount of output ripple voltage is primarily a function of the equivalent series resistance (ESR ) of the output capacitor and the amplitude of the inductor ripple current, IIND (see the Inductor Ripple Current (iIND) section). The lower capacitor values (100 F to 330 F) allows typically 50 mV to 150 mV of output ripple voltage, while larger-value capacitors reduce the ripple to approximately 20 mV to 50 mV (as seen in Equation 5). Output Ripple Voltage = (IIND) (ESR of COUT) (5) To further reduce the output ripple voltage, several standard electrolytic capacitors can be paralleled, or a highergrade capacitor can be used. Such capacitors are often called high-frequency, low-inductance, or low-ESR. These reduce the output ripple to 10 mV or 20 mV. However, when operating in the continuous mode, reducing the ESR below 0.03 can cause instability in the regulator. Tantalum capacitors can have a very low ESR, and must be carefully evaluated if it is the only output capacitor. Because of their good low temperature characteristics, a tantalum can be used in parallel with aluminum electrolytics, with the tantalum making up 10% or 20% of the total capacitance. The ripple current rating of the capacitor at 52 kHz must be at least 50% higher than the peak-to-peak inductor ripple current. 8.1.5 Catch Diode Buck regulators require a diode to provide a return path for the inductor current when the switch is off. This diode must be located close to the LM2574 using short leads and short printed-circuit traces. 16 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 Application Information (continued) Because of their fast switching speed and low forward voltage drop, Schottky diodes provide the best efficiency, especially in low output voltage switching regulators (less than 5 V). Fast-recovery, high-efficiency, or ultra-fast recovery diodes are also suitable, but some types with an abrupt turnoff characteristic can cause instability and EMI problems. A fast-recovery diode with soft recovery characteristics is a better choice. Standard 60-Hz diodes (for example, 1N4001 or 1N5400, and so forth) are also not suitable. See Table 1 for Schottky and soft fastrecovery diode selection guide. Table 1. Diode Selection Guide VR 1-A DIODES SCHOTTKY 20 V 1N5817 SR102 MBR120P 30 V 1N5818 SR103 11DQ03 MBR130P 10JQ030 40 V 1N5819 SR104 11DQ04 11JQ04 MBR140P 50 V MBR150 SR105 11DQ05 11JQ05 60 V MBR160 SR106 11DQ06 11JQ06 90 V 11DQ09 FAST RECOVERY The following diodes are all rated to 100 V 11DF1 10JF1 MUR110 HER102 8.1.6 Output Voltage Ripple and Transients The output voltage of a switching power supply contains a sawtooth ripple voltage at the switcher frequency, typically about 1% of the output voltage, and can also contain short voltage spikes at the peaks of the sawtooth waveform. The output ripple voltage is due mainly to the inductor sawtooth ripple current multiplied by the ESR of the output capacitor (see the Inductor Selection section). The voltage spikes are present because of the fast switching action of the output switch, and the parasitic inductance of the output filter capacitor. To minimize these voltage spikes, special low inductance capacitors can be used, and their lead lengths must be kept short. Wiring inductance, stray capacitance, as well as the scope probe used to evaluate these transients, all contribute to the amplitude of these spikes. An additional small LC filter (20 H and 100 F) can be added to the output (as shown in Figure 18) to further reduce the amount of output ripple and transients. A 10 x reduction in output ripple voltage and transients is possible with this filter. 8.1.7 Feedback Connection The LM2574 (fixed voltage versions) feedback pin must be wired to the output voltage point of the switching power supply. When using the adjustable version, physically locate both output voltage programming resistors near the LM2574 to avoid picking up unwanted noise. Avoid using resistors greater than 100 k because of the increased chance of noise pickup. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 17 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 8.1.8 ON/OFF Input For normal operation, the ON/OFF pin must be grounded or driven with a low-level TTL voltage (typically less than 1.6 V). To put the regulator into standby mode, drive this pin with a high-level TTL or CMOS signal. The ON/OFF pin can be safely pulled up to +VIN without a resistor in series with it. The ON/OFF pin must not be left open. 8.1.9 Additional Applications 8.1.9.1 Inverting Regulator Figure 20 shows a LM2574-12 in a buck-boost configuration to generate a negative 12-V output from a positive input voltage. This circuit bootstraps the ground pin of the regulator to the negative output voltage, then by grounding the feedback pin, the regulator senses the inverted output voltage and regulates it to -12 V. Note: Pin numbers are for the 8-pin PDIP package. Figure 20. Inverting Buck-Boost Develops, 12 V For an input voltage of 8 V or more, the maximum available output current in this configuration is approximately 100 mA. At lighter loads, the minimum input voltage required drops to approximately 4.7 V. The switch currents in this buck-boost configuration are higher than in the standard buck-mode design, thus lowering the available output current. Also, the start-up input current of the buck-boost converter is higher than the standard buck-mode regulator, which can overload an input power source with a current limit less than 0.6 A. Using a delayed turnon or an undervoltage lockout circuit (described in the Negative Boost Regulator section) would allow the input voltage to rise to a high enough level before the switcher would be allowed to turn on. Because of the structural differences between the buck and the buck-boost regulator topologies, the design procedure can not be used to select the inductor or the output capacitor. The recommended range of inductor values for the buck-boost design is between 68 H and 220 H, and the output capacitor values must be larger than what is normally required for buck designs. Low-input voltages or high-output currents require a large value output capacitor (in the thousands of micro Farads). The peak inductor current, which is the same as the peak switch current, can be calculated from Equation 6. IP ILOAD (VIN + VOUT VIN ) + VIN VOUT VIN + VOUT 1 2 L 1 f OSC where * fosc = 52 kHz. Under normal continuous inductor current operating conditions, the minimum VIN represents the worst case. Select an inductor that is rated for the peak current anticipated. (6) Also, the maximum voltage appearing across the regulator is the absolute sum of the input and output voltage. For a -12-V output, the maximum input voltage for the LM2574 is 28 V, or 48 V for the LM2574HV. 18 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 8.1.9.2 Negative Boost Regulator Another variation on the buck-boost topology is the negative boost configuration. The circuit in Figure 21 accepts an input voltage ranging from -5 V to -12 V and provides a regulated -12-V output. Input voltages greater than -12 V causes the output to rise greater than -12 V, but does not damage the regulator. Note: Pin numbers are for 8-pin PDIP package. Figure 21. Negative Boost Because of the boosting function of this type of regulator, the switch current is relatively high, especially at low input voltages. Output load current limitations are a result of the maximum current rating of the switch. Also, boost regulators cannot provide current-limiting load protection in the event of a shorted load, so some other means (such as a fuse) may be necessary. 8.2 Typical Applications 8.2.1 Fixed Output Voltage Applications CIN: 22 F, 75 V Aluminum electrolytic COUT: 220 F, 25 V Aluminum electrolytic D1: Schottky, 11DQ06 L1: 330 H, 52627 (for 5 V in, 3.3 V out, use 100 H, RL-1284-100) R1: 2k, 0.1% R2: 6.12k, 0.1% Figure 22. Fixed Output Voltage Versions Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 19 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Typical Applications (continued) 8.2.1.1 Design Requirements The design requirements for the fixed output voltage application are provided in Table 2. Table 2. Design Parameters PARAMETER EXAMPLE VALUE Regulated output voltage (3.3 V, 5 V, 12 V, or 15 V), VOUT 5V Maximum input voltage, VIN(Max) 15 V Maximum load current, ILOAD(Max) 0.4 A 8.2.1.2 Detailed Design Procedure 8.2.1.2.1 Custom Design With WEBENCH(R) Tools Click here to create a custom design using the LM2574 device with the WEBENCH(R) Power Designer. 1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements. 2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial. 3. Compare the generated design with other possible solutions from Texas Instruments. The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time pricing and component availability. In most cases, these actions are available: * Run electrical simulations to see important waveforms and circuit performance * Run thermal simulations to understand board thermal performance * Export customized schematic and layout into popular CAD formats * Print PDF reports for the design, and share the design with colleagues Get more information about WEBENCH tools at www.ti.com/WEBENCH. 8.2.1.2.2 Inductor Selection (L1) Select the correct inductor value selection guide from Figure 23, Figure 24, Figure 25, or Figure 26 (output voltages of 3.3 V, 5 V, 12 V, or 15 V respectively). From the inductor value selection guide, identify the inductance region intersected by VIN(Max) and ILOAD(Max). The inductance area intersected by the 15-V line and 0.4-A line is 330. Select an appropriate inductor from Table 3. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the LM2574 switching frequency (52 kHz) and for a current rating of 1.5 x ILOAD. For additional inductor information, see the Inductor Selection section. The required inductor value is 330 H. From Table 3, choose Pulse Engineering PE-52627, Renco RL-1284-330, or NPI NP5920/5921. 20 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 Table 3. Inductor Selection By Manufacturer's Part Number INDUCTOR VALUE PULSE ENG. RENCO NPI 68 H * RL-1284-68-43 NP5915 100 H * RL-1284-100-43 NP5916 150 H 52625 RL-1284-150-43 NP5917 220 H 52626 RL-1284-220-43 NP5918/5919 330 H 52627 RL-1284-330-43 NP5920/5921 470 H 52628 RL-1284-470-43 NP5922 680 H 52629 RL-1283-680-43 NP5923 1000 H 52631 RL-1283-1000-43 * 1500 H * RL-1283-1500-43 * 2200 H * RL-1283-2200-43 * 8.2.1.2.3 Output Capacitor Selection (COUT) The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching regulator loop. For stable operation and an acceptable output ripple voltage, (approximately 1% of the output voltage) a value between 100 F and 470 F is recommended. COUT = 100-F to 470-F standard aluminum electrolytic. The voltage rating of the capacitor must be at least 1.5 times greater than the output voltage. For a 5-V regulator, a rating of at least 8 V is appropriate, and a 10-V or 15-V rating is recommended. Capacitor voltage rating = 20 V. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this reason it can be necessary to select a capacitor rated for a higher voltage than would normally be needed. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 21 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 8.2.1.2.4 Catch Diode Selection (D1) The catch-diode current rating must be at least 1.5 times greater than the maximum load current. Also, if the power supply design must withstand a continuous output short, the diode must have a current rating equal to the maximum current limit of the LM2574. The most stressful condition for this diode is an overload or shorted output condition. For this example, a 1-A current rating is adequate. The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 20-V 1N5817 or SR102 Schottky diode, or any of the suggested fast-recovery diodes shown in Table 1. 8.2.1.2.5 Input Capacitor (CIN) An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable operation. A 22-F aluminum electrolytic capacitor located near the input and ground pins provides sufficient bypassing. 8.2.2 Application Curves 22 Figure 23. 3.3-V LM2574HV Inductor Selection Guide Figure 24. 5-V LM2574HV Inductor Selection Guide Figure 25. 12-V LM2574HV Inductor Selection Guide Figure 26. 15-V LM2574HV Inductor Selection Guide Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 8.2.3 Adjustable Output Voltage Applications Figure 27. Adjustable Output Voltage Version 8.2.3.1 Design Requirements The design requirements for the fixed output voltage application are provided in Table 4. Table 4. Design Parameters PARAMETER EXAMPLE VALUE Regulated output voltage, VOUT 24 V Maximum input voltage, VIN(Max) 40 V Maximum load current, ILOAD(Max) 0.4 A Switching frequency, F 52 kHz 8.2.3.2 Detailed Design Procedure 8.2.3.2.1 Programming Output Voltage Selecting R1 and R2, as shown in Figure 27. Use Equation 7 to select the appropriate resistor values. ae R o VOUT = VREF c 1 + 2 / R1 o e where * VREF = 1.23 V (7) R1 can be between 1 k and 5 k as in Equation 8. For best temperature coefficient and stability with time, use 1% metal film resistors. aeV o R 2 = R 1 c OUT - 1/ V e REF o (8) For this example, use Equation 9 and Equation 10. ae R o VOUT = 1.23 c 1 + 2 / R1 o e select * R1 = 1 k (9) aeV o ae 24 V o R 2 = R 1 c OUT - 1/ = 1k c - 1/ e 1.23 V o e VREF o (10) R2 = 1 k (19.51-1) = 18.51 k, closest 1% value is 18.7 k Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 23 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 8.2.3.2.2 Inductor Selection (L1) Calculate the inductor Volt x microsecond constant, E x T (V x s), from Equation 11. V 1000 E T = (VIN - VOUT ) OUT (V s ) VIN F (kHz ) (11) For this example, calculate E x T (V x s) using Equation 12. 24 1000 E T = (40 - 24 ) = 185 V s 40 52 (12) Use the E x T value from the previous formula and match it with the E x T number on the vertical axis of the inductor value selection guide shown in Figure 32. For this example, E x T = 185 V x s. On the horizontal axis, select the maximum load current, ILOAD(Max) = 0.4 A. Identify the inductance region intersected by the E x T value and the maximum load current value, and note the inductor value for that region, inductance region = 1000. Select an appropriate inductor from Table 3. Part numbers are listed for three inductor manufacturers. The inductor chosen must be rated for operation at the LM2574 switching frequency (52 kHz) and for a current rating of 1.5 x ILOAD. For additional inductor information, see the Inductor Selection section. 8.2.3.2.3 Output Capacitor Selection (COUT) The value of the output capacitor together with the inductor defines the dominate pole-pair of the switching regulator loop. For stable operation, the capacitor must satisfy the requirement in Equation 13. VIN(MAX ) C OUT 13300 (F ) VOUT L (H) (13) Equation 13 yields capacitor values between 5 F and 1000 F that satisfies the loop requirements for stable operation. To achieve an acceptable output ripple voltage, (approximately 1% of the output voltage) and transient response, the output capacitor may need to be several times larger than the above formula yields. The voltage rating of the capacitor must be at last 1.5 times greater than the output voltage. For a 24-V regulator, a rating of at least 35 V is recommended. Higher voltage electrolytic capacitors generally have lower ESR numbers, and for this reason, it can be necessary to select a capacitor rate for a higher voltage than would normally be needed. 40 C OUT > 13300 = 22.2 F 24 1000 (14) However, for acceptable output ripple voltage select: COUT 100 F COUT = 100 F electrolytic capacitor 8.2.3.2.4 Catch Diode Selection (D1) The catch-diode current rating must be at least 1.5 times greater than the maximum load current. Also, if the power supply design must withstand a continuous output short, the diode must have a current rating equal to the maximum current limit of the LM2574. The most stressful condition for this diode is an overload or shorted output condition. Suitable diodes are shown in Table 1. For this example, a 1-A current rating is adequate. The reverse voltage rating of the diode must be at least 1.25 times the maximum input voltage. Use a 50-V MBR150 or 11DQ05 Schottky diode, or any of the suggested fast-recovery diodes in Table 1. 8.2.3.2.5 Input Capacitor (CIN) An aluminum or tantalum electrolytic bypass capacitor located close to the regulator is needed for stable operation. A 22-F aluminum electrolytic capacitor located near the input and ground pins provides sufficient bypassing (see Table 1). 24 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 8.2.3.3 Application Curves Output pin voltage, 10 V/div Inductor current, 0.2 A/div Output ripple voltage 20 mV/div AC-coupled Horizontal time base 5 s/div VOUT = 5 V 500-mA load current L = 330 h Figure 28. Continuous Mode Switching Waveforms Output voltage, 50 V/div AC-coupled 100-mA to 500-mA load pulse Horizontal time base: 200 s/div 500 mA load L = 330 h COUT = 300 f Figure 30. Transient Response for Continuous Mode Operation Output pin voltage, 10 V/div Inductor current, 0.2 A/div Output ripple voltage 20 mV/div AC-coupled Horizontal time base 5 s/div VOUT = 5 V 100-mA load current L = 100 h Figure 29. Discontinuous Mode Switching Waveforms Output voltage, 50 V/div, AC-coupled 50-mA to 250-mA load pulse Horizontal time base: 200 s/div 250 mA load L = 68 h COUT = 470 f Figure 31. Transient Response for Discontinuous Mode Operation Figure 32. Adjustable LM2574HV Inductor Selection Guide Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 25 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com 9 Power Supply Recommendations As in any switching regulator, layout is very important. Rapidly switching currents associated with wiring inductance generate voltage transients which can cause problems. For minimal inductance and ground loops, the length of the leads indicated by heavy lines must be kept as short as possible. Single-point grounding (as indicated) or ground plane construction must be used for best results. When using the adjustable version, physically locate the programming resistors near the regulator, to keep the sensitive feedback wiring short. 10 Layout 10.1 Layout Guidelines The layout is critical for the proper operation of switching power supplies. First, the ground plane area must be sufficient for thermal dissipation purposes. Second, appropriate guidelines must be followed to reduce the effects of switching noise. Switch mode converters are very fast switching devices. In such cases, the rapid increase of input current combined with the parasitic trace inductance generates unwanted L di/dt noise spikes. The magnitude of this noise tends to increase as the output current increases. This noise can turn into electromagnetic interference (EMI) and can also cause problems in device performance. Therefore, take care in the layout to minimize the effect of this switching noise. The most important layout rule is to keep the AC current loops as small as possible. Figure 33 shows the current flow in a buck converter. The top schematic shows a dotted line which represents the current flow during the top switch ON-state. The middle schematic shows the current flow during the top switch OFF-state. The bottom schematic shows the currents referred to as AC currents. These AC currents are the most critical because they are changing in a very short time period. The dotted lines of the bottom schematic are the traces to keep as short and wide as possible. This also yields a small loop area reducing the loop inductance. To avoid functional problems due to layout, review the PCB layout example. Best results are achieved if the placement of the LM2574 device, the bypass capacitor, the Schottky diode, RFBB, RFBT, and the inductor are placed as shown in the example. In the layout shown, R1 = RFBB and R2 = RFBT. TI also recommends using 2-oz. copper boards or heavier to help thermal dissipation and to reduce the parasitic inductances of board traces. See the application note AN-1229 SIMPLE SWITCHER(R) PCB Layout Guidelines for more information. Figure 33. Buck Converter Current Flow 26 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 10.2 Layout Example Figure 34. LM2574 Adjustable Output Voltage Layout 10.3 Grounding The 8-pin molded PDIP and the 14-pin SOIC package have separate power and signal ground pins. Both ground pins must be soldered directly to wide printed-circuit board copper traces to assure low inductance connections and good thermal properties. 10.4 Thermal Considerations The 8-pin PDIP (P) package and the 14-pin SOIC (NPA) package are molded plastic packages with solid copper lead frames. The copper lead frame conducts the majority of the heat from the die, through the leads, to the printed-circuit board copper, which acts as the heat sink. For best thermal performance, wide copper traces must be used, and all ground and unused pins must be soldered to generous amounts of printed-circuit board copper, such as a ground plane. Large areas of copper provide the best transfer of heat (lower thermal resistance) to the surrounding air, and even double-sided or multilayer boards provide better heat paths to the surrounding air. Unless the power levels are small, using a socket for the 8-pin package is not recommended because of the additional thermal resistance it introduces, and the resultant higher junction temperature. Because of the 0.5-A current rating of the LM2574, the total package power dissipation for this switcher is quite low, ranging from approximately 0.1 W up to 0.75 W under varying conditions. In a carefully engineered printedcircuit board, both the P and the NPA package can easily dissipate up to 0.75 W, even at ambient temperatures of 60C, and still keep the maximum junction temperature less than 125C. A curve, Figure 14, displaying thermal resistance versus PCB area for the two packages is shown in the Typical Characteristics. These thermal resistance numbers are approximate, and there can be many factors that affect the final thermal resistance. Some of these factors include board size, shape, thickness, position, location, and board temperature. Other factors are, the area of printed-circuit copper, copper thickness, trace width, multi-layer, single- or double-sided, and the amount of solder on the board. The effectiveness of the PCB to dissipate heat also depends on the size, number and spacing of other components on the board. Furthermore, some of these components, such as the catch diode and inductor generate some additional heat. Also, the thermal resistance decreases as the power level increases because of the increased air current activity at the higher power levels, and the lower surface to air resistance coefficient at higher temperatures. The data sheet thermal resistance curves can estimate the maximum junction temperature based on operating conditions. ln addition, the junction temperature can be estimated in actual circuit operation by using Equation 15. Tj = Tcu + (j-cu x PD) (15) Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 27 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Thermal Considerations (continued) With the switcher operating under worst case conditions and all other components on the board in the intended enclosure, measure the copper temperature (Tcu ) near the IC. This can be done by temporarily soldering a small thermocouple to the PCB copper near the IC, or by holding a small thermocouple on the PCB copper using thermal grease for good thermal conduction. The thermal resistance (j-cu) for the two packages is: j-cu = 42C/W for the P-8 package j-cu = 52C/W for the NPA-14 package The power dissipation (PD) for the IC could be measured, or it can be estimated by using Equation 16. V PD = VIN IS + OUT ILOAD VSAT VIN where * 28 IS is obtained from the typical supply current curve (adjustable version use the supply current vs duty cycle curve) (16) Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.1.2 Custom Design With WEBENCH(R) Tools Click here to create a custom design using the LM2574 device with the WEBENCH(R) Power Designer. 1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements. 2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial. 3. Compare the generated design with other possible solutions from Texas Instruments. The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time pricing and component availability. In most cases, these actions are available: * Run electrical simulations to see important waveforms and circuit performance * Run thermal simulations to understand board thermal performance * Export customized schematic and layout into popular CAD formats * Print PDF reports for the design, and share the design with colleagues Get more information about WEBENCH tools at www.ti.com/WEBENCH. 11.1.3 Device Nomenclature 11.1.3.1 Buck Regulator A switching regulator topology in which a higher voltage is converted to a lower voltage. Also known as a stepdown switching regulator. 11.1.3.2 Buck-Boost Regulator A switching regulator topology in which a positive voltage is converted to a negative voltage without a transformer. 11.1.3.3 Duty Cycle (D) The ratio of the ON-time of the output switch to the oscillator period calculated with Equation 17 for buck regulators and Equation 18 for buck-boost regulators. t V D = ON = OUT T VIN (17) D= VOUT t ON = T VOUT + VIN (18) 11.1.3.4 Catch Diode or Current Steering Diode This diode provides a return path for the load current when the LM2574 switch is OFF. In terms of efficiency (), the proportion of input power actually delivered to the load calculated with Equation 19. P POUT h = OUT = PIN POUT + PLOSS (19) Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 29 LM2574, LM2574HV SNVS104F - JUNE 1999 - REVISED MAY 2020 www.ti.com Device Support (continued) 11.1.3.5 Capacitor Equivalent Series Resistance (ESR) The purely resistive component of a real capacitor's impedance (see Figure 35) can causes power loss resulting in capacitor heating, which directly affects the operating lifetime of the capacitor. When used as a switching regulator output filter, higher ESR values result in higher output ripple voltages. Figure 35. Simple Model Of A Real Capacitor Most standard aluminum electrolytic capacitors in the 100 F to 1000 F range have 0.5- to 0.1- ESR. Highergrade capacitors (low-ESR, high-frequency, or low-inductance) in the 100 F to 1000 F range generally have ESR of less than 0.15 . 11.1.3.6 Equivalent Series Inductance (ESL) The pure inductance component of a capacitor is seen in Figure 35. The amount of inductance is determined to a large extent on the capacitor's construction. In a buck regulator, this unwanted inductance causes voltage spikes to appear on the output. 11.1.3.7 Output Ripple Voltage The AC component of the output voltage of the switching regulator is usually dominated by the output capacitor's ESR multiplied by the inductor's ripple current (IIND). The peak-to-peak value of this sawtooth ripple current can be determined by reading Inductor Ripple Current (iIND). 11.1.3.8 Capacitor Ripple Current The RMS value of the maximum allowable alternating current at which a capacitor can be operated continuously at a specified temperature. 11.1.3.9 Standby Quiescent Current (ISTBY) Supply current required by the LM2574 when in the standby mode (ON/OFF pin is driven to TTL-high voltage, thus turning the output switch OFF). 11.1.3.10 Inductor Ripple Current (iIND) The peak-to-peak value of the inductor current waveform, typically a sawtooth waveform when the regulator is operating in the continuous mode (vs. discontinuous mode). 11.1.3.11 Continuous and Discontinuous Mode Operation These mode operations relate to the inductor current. In the continuous mode, the inductor current is always flowing and never drops to zero, versus the discontinuous mode, where the inductor current drops to zero for a period of time in the normal switching cycle. 11.1.3.12 Inductor Saturation The condition which exists when an inductor cannot hold any more magnetic flux. When an inductor saturates, the inductor appears less inductive and the resistive component dominates. Inductor current is then limited only by the DC resistance of the wire and the available source current. 11.1.3.13 Operating Volt Microsecond Constant (E x Top) The product (in VoIt x s) of the voltage applied to the inductor and the time the voltage is applied. This E x Top constant is a measure of the energy handling capability of an inductor and is dependent upon the type of core, the core area, the number of turns, and the duty cycle. 30 Submit Documentation Feedback Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV LM2574, LM2574HV www.ti.com SNVS104F - JUNE 1999 - REVISED MAY 2020 11.2 Documentation Support 11.2.1 Related Documentation For related documentation see the following: Texas Instruments, AN-1229 SIMPLE SWITCHER(R) PCB Layout Guidelines Application Report (SNVA054) 11.3 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed. For change details, review the revision history included in any revised document. 11.4 Support Resources TI E2ETM support forums are an engineer's go-to source for fast, verified answers and design help -- straight from the experts. Search existing answers or ask your own question to get the quick design help you need. Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. 11.5 Trademarks E2E is a trademark of Texas Instruments. WEBENCH, SIMPLE SWITCHER are registered trademarks of Texas Instruments. All other trademarks are the property of their respective owners. 11.6 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.7 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright (c) 1999-2020, Texas Instruments Incorporated Product Folder Links: LM2574 LM2574HV Submit Documentation Feedback 31 PACKAGE OPTION ADDENDUM www.ti.com 11-Jan-2021 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) (3) Device Marking (4/5) (6) LM2574HVM-12/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -12 P+ LM2574HVM-15 NRND SOIC NPA 14 50 Non-RoHS & Green Call TI Call TI -40 to 125 LM2574HVM -15 P+ LM2574HVM-15/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -15 P+ LM2574HVM-3.3/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -3.3 P+ LM2574HVM-5.0 NRND SOIC NPA 14 50 Non-RoHS & Green Call TI Call TI -40 to 125 LM2574HVM -5.0 P+ LM2574HVM-5.0/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -5.0 P+ LM2574HVM-ADJ/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -ADJ P+ LM2574HVMX-12/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -12 P+ LM2574HVMX-15/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -15 P+ LM2574HVMX-3.3/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-4-260C-72 HR -40 to 125 LM2574HVM -3.3 P+ LM2574HVMX-5.0 NRND SOIC NPA 14 1000 Non-RoHS & Green Call TI Call TI -40 to 125 LM2574HVM -5.0 P+ LM2574HVMX-5.0/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -5.0 P+ LM2574HVMX-ADJ/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574HVM -ADJ P+ LM2574HVN-12/NOPB ACTIVE PDIP P 8 40 RoHS & Green Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574HVN -12 P+ LM2574HVN-15/NOPB ACTIVE PDIP P 8 40 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2574HVN -15 P+ LM2574HVN-5.0/NOPB ACTIVE PDIP P 8 40 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2574HVN -5.0 P+ LM2574HVN-ADJ/NOPB ACTIVE PDIP P 8 40 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2574HVN Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Jan-2021 Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) (6) -ADJ P+ LM2574M-12/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -12 P+ LM2574M-3.3/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -3.3 P+ LM2574M-5.0 NRND SOIC NPA 14 50 Non-RoHS & Green Call TI Call TI -40 to 125 LM2574M -5.0 P+ LM2574M-5.0/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -5.0 P+ LM2574M-ADJ NRND SOIC NPA 14 50 Non-RoHS & Green Call TI Call TI -40 to 125 LM2574M -ADJ P+ LM2574M-ADJ/NOPB ACTIVE SOIC NPA 14 50 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -ADJ P+ LM2574MX-12/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -12 P+ LM2574MX-3.3/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-4-260C-72 HR -40 to 125 LM2574M -3.3 P+ LM2574MX-5.0/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -5.0 P+ LM2574MX-ADJ/NOPB ACTIVE SOIC NPA 14 1000 RoHS & Green SN Level-3-260C-168 HR -40 to 125 LM2574M -ADJ P+ LM2574N-12/NOPB ACTIVE PDIP P 8 40 RoHS & Green Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N -12 P+ LM2574N-3.3/NOPB ACTIVE PDIP P 8 40 RoHS & Green Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N -3.3 P+ LM2574N-5.0/NOPB ACTIVE PDIP P 8 40 RoHS & Green Call TI | SN Level-1-NA-UNLIM -40 to 125 LM2574N -5.0 P+ LM2574N-ADJ/NOPB ACTIVE PDIP P 8 40 RoHS & Green SN Level-1-NA-UNLIM -40 to 125 LM2574N -ADJ P+ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Jan-2021 (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 17-Apr-2020 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM2574HVMX-12/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574HVMX-15/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574HVMX-3.3/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574HVMX-5.0 SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574HVMX-5.0/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574HVMX-ADJ/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574MX-12/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574MX-3.3/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574MX-5.0/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 LM2574MX-ADJ/NOPB SOIC NPA 14 1000 330.0 16.4 10.9 9.5 3.2 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 17-Apr-2020 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM2574HVMX-12/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574HVMX-15/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574HVMX-3.3/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574HVMX-5.0 SOIC NPA 14 1000 367.0 367.0 38.0 LM2574HVMX-5.0/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574HVMX-ADJ/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574MX-12/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574MX-3.3/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574MX-5.0/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 LM2574MX-ADJ/NOPB SOIC NPA 14 1000 367.0 367.0 38.0 Pack Materials-Page 2 MECHANICAL DATA NPA0014B www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2021, Texas Instruments Incorporated