FNA25060 - APTINA IMAGING - Product.Network

May, 2020 − Rev. 2

1Publication Order Number:

FNA25060/D

Motion SPM) 2 Series, 600 V

FNA25060

General Description

The FNA25060 is a Motion SPM 2 module providing

a fully−featured, high−performance inverter output stage for AC

induction, BLDC, and PMSM motors. These modules integrate

optimized gate drive of the built−in IGBTs to minimize EMI and

losses, while also providing multiple on−module protection features:

under−voltage lockouts, over−current shutdown, temperature sensing,

and fault reporting. The built−in, high−speed HVIC requires only

a single supply voltage and translates the incoming logic−level gate

inputs to high−voltage, high−current drive signals to properly drive the

module’s internal IGBTs. Separate negative IGBT terminals are

available for each phase to support the widest variety of control

algorithms.

Features

•UL Certified No. E209204 (UL1557)

•600 V − 50 A 3−Phase IGBT Inverter, Including Control ICs for

Gate Drive and Protections

•Low−Loss, Short−Circuit−Rated IGBTs

•Very Low Thermal Resistance Using Al2O3 DBC Substrate

•Built−In Bootstrap Diodes and Dedicated Vs Pins Simplify PCB

Layout

•Separate Open−Emitter Pins from Low−Side IGBTs for Three−Phase

Current Sensing

•Single−Grounded Power Supply Supported

•Built−In NTC Thermistor for Temperature Monitoring and

Management

•Adjustable Over−Current Protection via Integrated Sense−IGBTs

•Isolation Rating of 2500 Vrms / 1 min.

•This Device is Pb−Free, Halogen Free/BFR Free and is RoHS

Compliant

Applications

•Motion Control − Industrial Motor (AC 200 V Class)

Related Resources

•AN−9121 − Users Guide for 600V SPM 2 Series

•AN−9076 − Mounting Guide for New SPM 2 Package

•AN−9079 − Thermal Performance of Motion SPM 2 Series by

Mounting Torque

SPMCA−A34

CASE MODFQ

See detailed ordering and shipping information on page 2 of

this data sheet.

ORDERING INFORMATION

www.onsemi.com

MARKING DIAGRAM

FNA25060 = Specific Device Code

$Y = ON Semiconductor Logo

&Z = Assembly Plant Code

&K = Lot Code

&E = Space Designator

&3 = 3−Digit Date Code

FNA25060

&Z&K&E&E&E&3

FNA25060

www.onsemi.com

PACKAGE MARKING AND ORDERING INFORMATION

Device Device Marking Package Packing Type Quantity

FNA25060 FNA25060 SPMCA−A34 Rail 6

Integrated Power Functions

•600 V − 50 A IGBT inverter for three−phase DC / AC

power conversion (refer to Figure 2)

Integrated Drive, Protection, and System Control Functions

•For inverter high−side IGBTs:

gate−drive circuit, high−voltage isolated high−speed

level−shifting control circuit,

Under−Voltage Lock−Out Protection (UVLO),

Available bootstrap circuit example is given in Figures

4 and 14

•For inverter low−side IGBTs:

gate−drive circuit, Short−Circuit Protection (SCP)

control circuit,

Under−Voltage Lock−Out Protection (UVLO)

•Fault signaling:

corresponding to UV (low−side supply) and SC faults

•Input interface:

active−HIGH interface, works with 3.3 / 5 V logic,

Schmitt−trigger input

Pin Configuration

Figure 1. Top View

FNA25060

www.onsemi.com

PIN DESCRIPTIONS

Pin No. Pin Name Pin Description

1 P Positive DC−Link Input

2 W Output for W Phase

3 V Output for V Phase

4 U Output for U Phase

5 NWNegative DC−Link Input for W Phase

6 NVNegative DC−Link Input for V Phase

7 NUNegative DC−Link Input for U Phase

8RTH Series Resistor for Thermistor (Temperature Detection)

9VTH Thermistor Bias Voltage

10 VCC(L) Low−Side Bias Voltage for IC and IGBTs Driving

11 COM(L) Low−Side Common Supply Ground

12 IN(UL) Signal Input for Low−Side U Phase

13 IN(VL) Signal Input for Low−Side V Phase

14 IN(WL) Signal Input for Low−Side W Phase

15 VFO Fault Output

16 CFOD Capacitor for Fault Output Duration Selection

17 CSC Capacitor (Low−Pass Filter) for Short−Circuit Current Detection Input

18 RSC Resistor for Short−Circuit Current Detection

19 IN(UH) Signal Input for High−Side U Phase

20 COM(H) High−Side Common Supply Ground

21 VCC(UH) High−Side Bias Voltage for U Phase IC

22 VBD(U) Anode of Bootstrap Diode for U Phase High−Side Bootstrap Circuit

23 VB(U) High−Side Bias Voltage for U Phase IGBT Driving

24 VS(U) High−Side Bias Voltage Ground for U Phase IGBT Driving

25 IN(VH) Signal Input for High−Side V Phase

26 VCC(VH) High−Side Bias Voltage for V Phase IC

27 VBD(V) Anode of Bootstrap Diode for V Phase High−Side Bootstrap Circuit

28 VB(V) High−Side Bias Voltage for V Phase IGBT Driving

29 VS(V) High−Side Bias Voltage Ground for V Phase IGBT Driving

30 IN(WH) Signal Input for High−Side W Phase

31 VCC(WH) High−Side Bias Voltage for W Phase IC

32 VBD(W) Anode of Bootstrap Diode for W Phase High−Side Bootstrap Circuit

33 VB(W) High−Side Bias Voltage for W Phase IGBT Driving

34 VS(W) High−Side Bias Voltage Ground for W Phase IGBT Driving

FNA25060

www.onsemi.com

Internal Equivalent Circuit and Input/Output Pins

Figure 2. Internal Block Diagram

NOTES:

1. Inverter high−side is composed of three normal−IGBTs, freewheeling diodes, and one control IC for each IGBT.

2. Inverter low−side is composed of three sense−IGBTs, freewheeling diodes, and one control IC for each IGBT.

It has gate drive and protection functions.

3. Inverter power side is composed of four inverter DC−link input terminals and three inverter output terminals.

FNA25060

www.onsemi.com

ABSOLUTE MAXIMUM RATINGS (TC = 25°C, Unless Otherwise Specified)

Symbol Parameter Conditions Rating Unit

INVERTER PART

VPN Supply Voltage Applied between P − NU, NV, NW450 V

VPN(Surge) Supply Voltage (Surge) Applied between P − NU, NV, NW500 V

VCES Collector − Emitter Voltage 600 V

±ICEach IGBT Collector Current TC = 25°C, TJ ≤ 150°C (Note 4) 50 A

±ICP Each IGBT Collector Current (Peak) TC = 25°C, TJ ≤ 150°C, Under 1 ms Pulse

Width (Note 4) 100 A

PCCollector Dissipation TC = 25°C per One Chip (Note 4) 192 W

TJOperating Junction Temperature −40 ∼ 150 °C

CONTROL PART

VCC Control Supply Voltage Applied between VCC(H), VCC(L) − COM 20 V

VBS High−Side Control Bias Voltage Applied between VB(U) − VS(U), VB(V) −

VS(V), VB(W) − VS(W)

20 V

VIN Input Signal Voltage Applied between IN(UH), IN(VH), IN(WH),

IN(UL), IN(VL), IN(WL) − COM −0.3 ∼ VCC+0.3 V

VFO Fault Output Supply Voltage Applied between VFO − COM −0.3 ∼ VCC+0.3 V

IFO Fault Output Current Sink Current at VFO pin 2 mA

VSC Current Sensing Input Voltage Applied between CSC − COM −0.3 ∼ VCC+0.3 V

BOOTSTRAP DIODE PART

VRRM Maximum Repetitive Reverse Voltage 600 V

IFForward Current TC = 25°C, TJ ≤ 150°C (Note 4) 1.0 A

IFP Forward Current (Peak) TC = 25°C, TJ ≤ 150°C, Under 1 ms Pulse

Width (Note 4) 2.0 A

TJOperating Junction Temperature −40 ∼ 150 °C

TOTAL SYSTEM

VPN(PROT) Self−Protection Supply Voltage Limit

(Short−Circuit Protection Capability) VCC = VBS = 13.5 ∼ 16.5 V, TJ = 150°C,

VCES < 600 V, Non−Repetitive, < 2 ms

400 V

TCModule Case Operation Temperature See Figure 2 −40 ∼ 125 °C

TSTG Storage Temperature −40 ∼ 125 °C

VISO Isolation Voltage 60 Hz, Sinusoidal, AC 1 Minute, Connection

Pins to Heat Sink Plate 2500 Vrms

THERMAL RESISTANCE

Symbol Parameter Conditions Min. Typ. Max. Unit

Rth(j−c)Q Junction to Case

Thermal Resistance (Note 5) Inverter IGBT Part (per 1 / 6 Module) − − 0.65 °C/W

Rth(j−c)F Inverter FWD Part (per 1 / 6 Module) − − 1.12 °C/W

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

4. These values had been made an acquisition by the calculation considered to design factor.

5. For the measurement point of case temperature (TC), please refer to Figure 1.

FNA25060

www.onsemi.com

ELECTRICAL CHARACTERISTICS (TJ = 25°C, unless otherwise specified)

Symbol Parameter Conditions Min. Typ. Max. Unit

INVERTER PART

VCE(SAT) Collector − Emitter Saturation Voltage VCC = VBS = 15 V

VIN = 5 V

IC = 50 A,

TJ = 25°C−1.50 2.10 V

VFFWDi Forward Voltage VIN = 0 V IF = 50 A,

TJ = 25°C

−1.80 2.40 V

HS tON Switching Times VPN = 300 V, VCC = 15 V, IC = 50 A

TJ = 25°C

VIN = 0 V ↔ 5 V, Inductive Load

See Figure 4

(Note 6)

0.80 1.30 1.90 ms

tC(ON) −0.30 0.70 ms

tOFF −1.20 1.80 ms

tC(OFF) −0.15 0.55 ms

trr −0.25 −ms

LS tON VPN = 300 V, VCC = 15 V, IC = 50 A

TJ = 25°C

VIN = 0 V ↔ 5 V, Inductive Load

See Figure 4

(Note 6)

0.50 1.00 1.60 ms

tC(ON) −0.30 0.70 ms

tOFF −1.20 1.80 ms

tC(OFF) −0.25 0.65 ms

trr −0.20 −ms

ICES Collector − Emitter Leakage Current VCE = VCES − − 5 mA

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

6. tON and tOFF include the propagation delay of the internal drive IC. tC(ON) and tC(OFF) are the switching times of IGBT under the given

gate−driving condition internally. For the detailed information, please see Figure 3.

Figure 3. Switching Time Definition

FNA25060

www.onsemi.com

One−Leg Diagram of SPM 2

NU,V,W

VC C

COM

OUT

VC C

COM

OUT

FO D

VFO

RSC

VP N

U,V,W

Inductor

HS Switching

LS Switching

RBS

15 V

5 V

4.7 kΩ

CB S

HS Switching

LS Switching

VIN

0 V

5 V VC C

−20 −100 102030405060708090100110120

100

150

200

250

300

350

400

450

500

550

600 R−T Curve

Resistance[kW]

50 60 70 80 90 100 110 120

Resistance[kΩ]

Figure 4. Example Circuit for Switching Test

Figure 5. Switching Loss Characteristics (Typical)

Figure 6. R−T Curve of Built−in Thermistor

R−T Curve in 50°C ~ 125°C

Temperature [°C]

Temperature TTH [5C]

FNA25060

www.onsemi.com

BOOTSTRAP DIODE PART

Symbol Parameter Conditions Min. Typ. Max. Unit

VFForward Voltage IF = 1.0 A, TJ = 25°C−2.2 −V

trr Reverse−Recovery Time IF = 1.0 A, dIF / dt = 50 A / μs,

TJ = 25°C

−80 −ns

CONTROL PART

Symbol Parameter Conditions Min. Typ. Max. Unit

IQCCH Quiescent VCC Supply Current VCC(UH,VH,WH) = 15 V,

IN(UH,VH,WH) = 0 V

VCC(UH) − COM(H),

VCC(VH) − COM(H),

VCC(WH) − COM(H)

− − 0.15 mA

IQCCL VCC(L) = 15 V,

IN(UL,VL, WL) = 0 V

VCC(L) − COM(L) − − 5.00 mA

IPCCH Operating VCC Supply Current VCC(UH,VH,WH) = 15 V,

fPWM = 20 kHz, Duty = 50%,

Applied to one PWM Signal

Input for High−Side

VCC(UH) − COM(H),

VCC(VH) − COM(H),

VCC(WH) − COM(H)

− − 0.30 mA

IPCCL VCC(L) = 15V, fPWM = 20 kHz,

Duty = 50%, Applied to one

PWM Signal Input for Low−Side

VCC(L) − COM(L) − − 9.00 mA

IQBS Quiescent VBS Supply Current VBS = 15 V, IN(UH, VH, WH) = 0 V VB(U) − VS(U),

VB(V) − VS(V),

VB(W) − VS(W)

− − 0.30 mA

IPBS Operating VBS Supply Current VCC = VBS = 15 V,

fPWM = 20 kHz,

Duty = 50%, Applied to one

PWM Signal Input for High−Side

VB(U) − VS(U),

VB(V) − VS(V),

VB(W) − VS(W)

− − 6.50 mA

VFOH Fault Output Voltage VCC = 15 V, VSC = 0 V, VFO Circuit: 4.7 kΩ to 5 V Pull−up 4.5 − − V

VFOL VCC = 15 V, VSC = 1 V, VFO Circuit: 4.7 kΩ to 5 V Pull−up − − 0.5 V

ISEN Sensing Current of Each Sense

IGBT

VCC = 15 V, VIN = 5 V,

RSC = 0 Ω,

No Connection of Shunt

Resistor at NU,V,W Terminal

IC = 50 A −20 −mA

VSC(ref) Short Circuit Trip Level VCC = 15 V (Note 7) CSC − COM(L) 0.43 0.50 0.57 V

ISC Short Circuit Current Level for

Trip

RSC = 18 Ω (±1%), No Connection of Shunt Resistor at

NU,V,W Terminal (Note 7) −100 −A

UVCCD Supply Circuit Under− Voltage

Protection

Detection Level 10.3 −12.8 V

UVCCR Reset Level 10.8 −13.3 V

UVBSD Detection Level 9.5 −12.0 V

UVBSR Reset Level 10.0 −12.5 V

tFOD Fault−Out Pulse Width CFOD = Open (Note 8) 50 − − ms

CFOD = 2.2 nF 1.7 − − ms

VIN(ON) ON Threshold Voltage Applied between IN(UH, VH, WH) − COM(H), IN(UL, VL, WL) −

COM(L)

− − 2.6 V

VIN(OFF) OFF Threshold Voltage 0.8 − − V

RTH Resistance of Thermistor at TTH = 25°CSee Figure 6

(Note 9)

−47 −kW

at TTH = 100°C−2.9 −kW

7. Short−circuit current protection functions only at the low−sides because the sense current is divided from main current at low−side IGBTs.

Inserting the shunt resistor for monitoring the phase current at NU, NV, NW terminal, the trip level of the short−circuit current is changed.

8. The fault−out pulse width tFOD depends on the capacitance value of CFOD according to the following approximate equation:

tFOD = 0.8 x 106 x CFOD [s].

9. TTH is the temperature of thermistor itself. To know case temperature (TC), conduct experiments considering the application.

FNA25060

www.onsemi.com

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Conditions

Value

Unit

Min. Typ. Max.

VPN Supply Voltage Applied between P − NU, NV, NW−300 400 V

VCC Control Supply Voltage Applied between VCC(UH, VH, WH) −

COM(H), VCC(L) − COM(L)

14.5 15.0 16.5 V

VBS High−Side Bias Voltage Applied between VB(U) − VS(U),

VB(V) − VS(V), VB(W) − VS(W) 13.5 15.0 18.5 V

dVCC / dt,

dVBS / dt

Control Supply Variation −1−1V / ms

tdead Blanking Time for Preventing Arm −

Short

For Each Input Signal 2.0 − − ms

fPWM PWM Input Signal −40_C ≤ TC ≤ 125_C,

−40_C ≤ TJ ≤ 150_C

− − 20 kHz

VSEN Voltage for Current Sensing Applied between NU, NV, NW −

COM(H, L)

(Including Surge Voltage)

−5 5 V

PWIN(ON) Minimun Input Pulse Width VCC = VBS = 15 V, IC ≤ 100 A,

Wiring Inductance between NU, V, W

and DC Link N < 10nH (Note 10)

2.5 − − ms

PWIN(OFF) 2.5 − −

TJJunction Temperature −40 −150 _C

Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond

the Recommended Operating Ranges limits may affect device reliability.

10.This product might not make right output response if input pulse width is less than the recommanded value.

Figure 7. Allowable Maximum Output Current

11. This allowable output current value is the reference data for the safe operation of this product. This may be different from the

actual application and operating condition.

FNA25060

www.onsemi.com

MECHANICAL CHARACTERISTICS AND RATINGS

Parameter Conditions Min. Typ. Max. Unit

Device Flatness See Figure 9 0−+200 mm

Mounting Torque Mounting Screw: M4

See Figure 10

Recommended 1.0 N/m 0.9 1.0 1.5 N/m

Recommended 10.1 kg/cm 9.1 10.1 15.1 kg/cm

Terminal Pulling Strength Load 19.6 N 10 − − s

Terminal Bending Strength Load 9.8 N, 90 degrees Bend 2− − times

Weight −50 −g

Figure 8. Flatness Measurement Position

(＋)

Pre − Screwing : 1 2

Final Screwing : 2 1

Figure 9. Mounting Screws Torque Order

NOTES:

12.Do not over torque when mounting screws. Too much mounting torque may cause DBC cracks, as well as bolts and Al heat−sink destruction.

13.Avoid one−sided tightening stress. Figure 9 shows the recommended torque order for the mounting screws. Uneven mounting can cause

the DBC substrate of package to be damaged. The pre−screwing torque is set to 20 ∼ 30% of maximum torque rating.

FNA25060

www.onsemi.com

Time Charts of SPMs Protective Function

Figure 10. Under−Voltage Protection (Low−Side)

Input Signal

Output Current

Fault Output Signal

Control

Supply Voltage

RESET

UVC CR

Protection

Circuit State SET RESET

UVC C D

a1 : Control supply voltage rises: after the voltage rises UVCCR, the circuits start to operate when the next input is applied.

a2 : Normal operation: IGBT ON and carrying current.

a3 : Under−voltage detection (UVCCD).

a4 : IGBT OFF in spite of control input condition.

a5 : Fault output operation starts with a fixed pulse width according to the condition of the external capacitor CFOD.

a6 : Under−voltage reset (UVCCR).

a7 : Normal operation: IGBT ON and carrying current by triggering next signal from LOW to HIGH.

Input Signal

Output Current

Fault Output Signal

Control

Supply Voltage

RESET

UVBSR

Protection

Circuit State SET RESET

UVBSD

b2 b4

High−level (no fault output )

Figure 11. Under−Voltage Protection (High−Side)

b1 : Control supply voltage rises: after the voltage reaches UVBSR, the circuits start to operate when the next input is applied.

b2 : Normal operation: IGBT ON and carrying current.

b3 : Under−voltage detection (UVBSD).

b4 : IGBT OFF in spite of control input condition, but there is no fault output signal.

b5 : Under−voltage reset (UVBSR).

b6 : Normal operation: IGBT ON and carrying current by triggering next signal from LOW to HIGH.

FNA25060

www.onsemi.com

Figure 12. Short−Circuit Current Protection (Low−Side Operation only)

Lower Arms

Control Input

Output Current

Sensing Voltage

of Sense Resistor

Fault Output Signal

SC referenc e v oltage

RC f ilt er circuit

time cons tant

delay

S C current t rip level

Protection

Circuit state SET RESET

c6 c7

Internal IGBT

Gate−Emitter Voltage

I nt ernal delay

at protection c irc uit

c1 : Normal operation: IGBT ON and carrying current.

c2 : Short−circuit current detection (SC trigger).

c3 : All low−side IGBTs gate are hard interrupted.

c4 : All low−side IGBTs turn OFF.

c5 : Fault output operation starts with a fixed pulse width according to the condition of the external capacitor CFOD.

c6 : Input HIGH: IGBT ON state, but during the active period of fault output, the IGBT doesn’t turn ON.

c7 : Fault output operation finishes, but IGBT doesn’t turn on until triggering the next signal from LOW to HIGH.

c8 : Normal operation: IGBT ON and carrying current.

Input/Output Interface Circuit

Figure 13. Recommended MCU I/O Interface Circuit

MCU

COM

+5V ( MCU or control power )

IN(UL) IN(VL) IN( WL)

IN(UH) IN(VH) IN(WH)

VFO

4.7 kΩSPM

14. RC coupling at each input might change depending on the PWM control scheme used in the application and the wiring impedance

of the application’s printed circuit board.

The input signal section of the Motion SPM 2 product integrates 5 kW (typ.) pull−down resistor. Therefore, when using an external

filtering resistor, please pay attention to the signal voltage drop at input terminal.

FNA25060

www.onsemi.com

Figure 14. Typical Application Circuit

15.To avoid malfunction, the wiring of each input should be as short as possible (less than 2 − 3 cm).

16.VFO output is an open−drain type. This signal line should be pulled up to the positive side of the MCU or control power supply with a resistor

that makes IFO up to 2 mA. Please refer to Figure 13.

17.Fault out pulse width can be adjust by capacitor C5 connected to the CFOD terminal.

18.Input signal is active−HIGH type. There is a 5 kΩ resistor inside the IC to pull−down each input signal line to GND. RC coupling circuits should

be adopted for the prevention of input signal oscillation. R1C1 time constant should be selected in the range 50 ~ 150 ns (recommended R1

= 100 W, C1 = 1 nF).

19.Each wiring pattern inductance of point A should be minimized (recommend less than 10 nH). Use the shunt resistor R4 of surface mounted

(SMD) type to reduce wiring inductance. To prevent malfunction, wiring of point E should be connected to the terminal of the shunt resistor

R4 as close as possible.

20. To insert the shunt resistor to measure each phase current at NU, NV

, NW terminal, it makes to change the trip level ISC about the short−ciruit

current.

21.To prevent errors of the protection function, the wiring of points B, C, and D should be as short as possible. The wiring of B between CSC

filter and RSC terminal should be divided at the point that is close to the terminal of sense resistor R5.

22.For stable protection function, use the sense resistor R5 with resistance variation within 1% and low inductance value.

23.In the short−circuit protection circuit, select the R6C6 time constant in the range 1.0 ∼ 1.5 ms. R6 should be selected with a minimum of 10

times larger resistance than sense resistor R5. Do enough evaluaiton on the real system because short−circuit protection time may vary

wiring pattern layout and value of the R6C6 time constant.

24.Each capacitor should be mounted as close to the pins of the Motion SPM 2 product as possible.

25. To prevent surge destruction, the wiring between the smoothing capacitor C7 and the P & GND pins should be as short as possible. The use

of a high−frequency non− inductive capacitor of around 0.1 ∼ 0.22 mF between the P & GND pins is recommended.

26.Relays are used in most systems of electrical equipments in industrial application. In these cases, there should be sufficient distance between

the MCU and the relays.

27. The Zener diode or transient voltage suppressor should be adapted for the protection of ICs from the surge destruction between each pair

of control supply terminals (recommanded Zener diode is 22 V / 1 W, which has the lower Zener impedance characteristic than about15 W).

28.C2 of around seven times larger than bootstrap capacitor C3 is recommended.

29.Please choose the electrolytic capacitor with good temperature characteristic in C3. Choose 0.1 ∼ 0.2 mF R−category ceramic capacitors with

good temperature and frequency characteristics in C4.

SPM is registered trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.

SPMCA−A34 / 34LD, PDD STD, DBC DIP TYPE

CASE MODFQ

ISSUE O

DATE 31 JAN 2017

MECHANICAL CASE OUTLINE

PACKAGE DIMENSIONS

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding

the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically

disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the

rights of others.

98AON13565G

DOCUMENT NUMBER:

DESCRIPTION:

Electronic versions are uncontrolled except when accessed directly from the Document Repository.

Printed versions are uncontrolled except when stamped “CONTROLLED COPY” in red.

PAGE 1 OF 1

SPMCA−A34 / 34LD, PDD STD, DBC DIP TYPE

www.onsemi.com

ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.

ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent

coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.

ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,

regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or

specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer

application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not

designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification

in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized

application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and

expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such

claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This

literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

TECHNICAL SUPPORT

North American Technical Support:

Voice Mail: 1 800−282−9855 Toll Free USA/Canada

Phone: 011 421 33 790 2910

LITERATURE FULFILLMENT:

Email Requests to: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Europe, Middle East and Africa Technical Support:

Phone: 00421 33 790 2910

For additional information, please contact your local Sales Representative

◊