1SD210F2
IGBT-Driver.com Page 1
Data Sheet
1SD210F2-FZ500R65KE3
Single-Channel SCALE Plug-and-Play IG BT
Driver
Ultra compact, high-performance driver for 2-level, 3-level and
multilevel converters
Abstract
The SCALE plug-and-play driver 1SD210F2-FZ500R65KE3 is a compact
single-channel intelligent gate driver designed for Infineon’s high-voltage
IGBTs of ty pes FZ500R65KE3(T) and FD500R65KE3T-K. The driver f eatures a
fiber-optic interface and a selectable operation mode vi a a jumper.
For drive rs adapted to other types of h igh-power and high-voltage IGBT modules, r efer
to www.IGBT-Driver.com/go/plug-and-play
Product Highlights Applications
Plug-and-play solution Three/multi-level converters
Protects the IGBT from sh ort-circuit failure Two-level converters
Active clamping of Vce at turn-off Medium-voltage converters
Extremely reliable; long service life High-voltage applications
No electro lytic capacitors Industrial drives
Gate curr ent up to –6A/+10A Traction
Fiber-optic links Railroad po wer supplies
Monitoring of supp l y volt age and fiber optics Wind-power converters
Switching fr eq uenc y DC to max. 2.3kHz Radiology and laser technology
Duty cycle 0... 100% Research
Suitab le DC /DC power supply as separate unit Almost a ll ot her conceivable
Shortens application development t im e applications
1SD210F2
Data Sheet 1SD210F2-FZ500R65KE3
Page 2 INTELLIGENT POWER ELECTRONICS
Important Notes
This data sheet contains only product-specific data. For a detailed description, must-
read application notes and common data that apply to the whole series, please refer to
the “Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT
Drivers”.
When applying SCALE plug-and-play drivers, please note that these drivers are
specifically adapted to a particular type of IGBT module. Therefore, the type
designation of SCALE plug-and-play drivers also includes the type designation of the
corresponding IGBT module. These drivers are not valid for IGBT modules other
than those specified. Incorrect use may result in failure.
Mechanical and Electrical Interfaces
Dimensio ns: 156 x 79.5 mm.
Mounting P r i nc i ple: Direct screw m ount on IGBT.
Interface Remarks Part type #
Drive signal inp ut (Standa r d) Fiber-optic receiver (Notes 14,16) HFBR-2522Z
Drive signal inp ut (Opt. 01) Fiber-optic receiver (Notes 14,16) HFBR-2522Z
Drive signal inp ut (Opt. 02) Fiber-optic receiver (Notes 14,20) HFBR-2412Z
Status output (Standard) Fiber-optic transmitter (Notes 14,17) HFBR-1522Z
Status output (Opt. 01) Fiber-optic transmitter (Notes 14,17) HFBR-1522Z
Status output (Opt. 02) Fiber-optic transmitter (Notes 14,21) HFBR-1412Z
Power supp ly c onnector On-board connector (Note 15) 77315-101-05
Power supply connector Designator Pin numbers
Ground GND (Note 19) 1, 2, 4, 5
Supply voltage
VDC
3
1SD210F2
Data Sheet 1SD210F2-FZ500R65KE3
IGBT-Driver.com Page 3
Absolute Maximum Ratings
Parameter Remarks Min Max Units
Supply voltage
VDC
VDC to GND (Note 1) 0 17.3 V
Gate pea k current
Iout
Note 8 -6 +10 A
Average supp ly c ur r ent
IDC
Standard and Opt. 1 (Note 3) 190 mA
Opt. 2 (No te 3) 225 mA
Output power gate driver Notes 3,11 2 W
Switching fr equency Note 11 2.3 kHz
DC-link volt age Note 5 4400 V
Operating temperature Note 11 -40 +85 °C
Storage temperature -40 +90 °C
Electrical Characteristics
All data refer to +25°C and
VDC
= 16.4V unl ess ot h erwise spec ified
Power supply Remarks Min Typ. Max Units
Nominal supply volta ge
VDC
VDC to GND (Note 1) 15.5 16.4 16.8 V
Supply current
IDC
Without loa d (Note 2)
Standard and Opt. 1 80 mA
Opt. 2 115 mA
Turn-on threshold
Vth
Note 4 14 V
Hysteresis on/o ff Note 4 1.0 V
Short-circuit protection Remarks Min Typ. Max Units
Vce-monitoring thresho ld Between aux. terminals 1200 V
Respon se time 3-level mode (Notes 10,18) 10.1 10.8 μs
Respon se time 2-level mode (Notes 6,18) 10.9 11.7 μs
Blocking time 2-level mode (Note 7) 1 s
Timing characteristics Remarks Min Typ. Max Units
Turn-on delay
tpd(on)
Note 12 430 ns
Turn-off delay
tpd(off)
Note 12 520 ns
Output ri se t i m e
tr(out)
Note 9 100 ns
Output fall time
tf(out)
Note 9 100 ns
Acknowledge delay time At status output (Note 13) 450 ns
Acknowledge pulse width At status output 0.7 1.8 μs
1SD210F2
Data Sheet 1SD210F2-FZ500R65KE3
Page 4 INTELLIGENT POWER ELECTRONICS
Gate ou tp ut Remarks Min Typ. Max Units
Turn-on gate resistor
Rg(on)
1.5 Ω
Turn-off gate resi stor
Rg(off)
10 Ω
Footnotes to the key data
1) Suppl y volt age s hig her than those s pe cifie d ca n lea d to the de st ru ctio n o f t he d ri ve r and pro te cti on
circuits on the output side. The gate-emitter voltage tracks the supply voltage. (Not regulated by
the gate drive unit.) The recommended DC/DC pow er s upply I SO 3 11 6I wi th hig h-volta ge insulatio n
capability is a suitable sep arate unit.
2) Static power consumption of the gate driver.
3) If the specified power consumption of the gate driver is exceeded on average, this indicates an
overload of the gate driver and the external DC/DC power supply ISO3116I.
4) Under-voltage monitoring of supply voltage of the gate driver. For a voltage lower than this limit,
the power modules are switched off.
5) This limit is due to active clamping. Refer to t he “Description and Application Manual for 1SD210F2
SCALE H igh-Voltage IGBT Drivers”.
6) Pulse width o f the dir ect output of t he g ate drive unit. (Excluding the delay of the gate resistors.)
7) Duration of blocking the command input (keeping the gate driver and the IGBT in the off-state)
after fault detection, i.e. power supply under-voltage lock out, or – only in 2-level mode – short-
circuit detection. (For three/multilevel mode, turn-off under the short-circuit condition is managed
by the host controller.)
8) The g ate current is limited by on-board gate r esistors.
9) Refers to the direct output of the gate drive unit. (Excluding the delay of the gate resistors.)
10) Including the delay of external fiber-optic links. Measured from the turn-on transition at direct
output of the gate drive unit (excluding the delay of the gate resistors) to the transition of the
status signal at the optical receiver on the host controller side .
11) Application-specific self-heating of gate drivers and IGBT modules, especially at high switching
frequency, must be taken into account. The switching frequency is usually limited due to the
switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be
incorpo rated in t he user’s a pplicatio n, no bindi ng recom mended val ue for self-he ating and t hus for
the maximum useable output power can be given. It is therefore recommended to check the gate
driver’s ambient temperature within the system.
12) Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the direct output of the
gate drive unit. (Excluding the delay of t he g ate resistors.)
13) Including the delay of external fiber-optic links. Measured from the transition of the turn-on or
turn-off command at the optical transmitter on the host controller side to the transition of the
acknowledge signal at the optical receiver on the host controller side.
14) The transceivers required at the host controller side are not supplied with the gate driver. It is
recommended to use the same types as used in the gate driver. For product information refer to
www.IGBT-Driver.com/go/fiberoptics
15) The connecto r and cab le to t he DC/DC p ower supply are not supplied with the gate driver, but via
FCI Inc. Recommended crimp contact housing: order code 65039-032; recommended crimp
contacts: 5 p c s, order code 48236-002. Refer to www.IGBT-Driver.com/go/fci
16) The recommended transmitter current at the host controller is 30-35mA, suitable for plastic optic
fibers with a length of less than 2.5 meters. A higher current may increase jitter or delay at turn-
off.
1SD210F2
Data Sheet 1SD210F2-FZ500R65KE3
IGBT-Driver.com Page 5
17) The transmitter current at the gate driver is 30-35mA.
18) The delay from the turn-on transition at direct output of the gate drive unit to the turn-on of the
IGBT amounts to about 1.2μs (due to gate resistors). But turn-off at short circuit takes place
without delay; so the real short-circuit time is 1.2μs shorter than the response time.
19) GND of the power supply is not at the same electrical potential as the auxiliary emitter terminal of
the IGBT. They should never be connected together.
20) The recommended transmitter current at the host controller is 60mA.
21) The transmitter current at the gate driver is about 65mA.
22) In order not to violate the short-circuit SOA of the IGBT module the supply voltage should not
exceed 16.5V.
Important Notice
The data contained in this product data sheet is intended exclusively for technically
trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance
with the respective sa f ety regulations is ma ndatory!
Any handling of electronic devices is subject to the general specifications for protecting
electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX
or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with
these standa rds). O therwise, this product may be damaged.
Legal Disclaimer
This data sheet specifies devices but cannot promise to deliver any specific
characteristics. No warranty or guarantee is given – either expressly or implicitly –
regarding delivery, performance or suitability.
CT-Concept Technologie AG reserves the right to make modifications to its technical
data and product specifications at any time without prior notice. The general terms and
conditions of d elivery of CT-Co ncept Technologie AG apply.
1SD210F2
Data Sheet 1SD210F2-FZ500R65KE3
Page 6 INTELLIGENT POWER ELECTRONICS
Ordering In f orma t i o n
The general terms and conditions o f delivery of CT-Concept Technologie AG apply.
Related IGBT CONCEPT Driver Type #
Infineon (eupec) FZ500R65KE3(T) 1SD210F2-FZ500R65KE3
Infineon (eupec) FD500R65KE3T-K 1SD210F2-FZ500R65KE3
Infineon (eupec) FZ500R65KE3(T) 1SD210F2-FZ500R65KE3 Opt. 01
Infineon (eupec) FD500R65KE3T-K 1SD210F2-FZ500R65KE3 Op t. 01
Infineon (eupec) FZ500R65KE3(T) 1SD210F2-F Z 500R6 5KE3 Op t. 02
Infineon (eupec) FD500R65KE3T-K 1SD210F2-FZ500R65KE3 Opt. 02
Opt. 01: Lateral fiber-optic interface (HFBR-2522Z and HFBR-1522Z), see “Description and Application
Manual for 1SD210F2 SCALE High-Volta g e IGBT Drivers”.
Opt. 02: Lateral fiber-optic interface with ST (HFBR-2412Z and HFBR-1412Z), see “Description and
Application Manual for 1SD210F2 SCALE Hi gh-Voltage IGBT Drivers”.
Information about Other Products
For drivers adapte d to other high-voltage IGBT modules
Direct link: www.IGBT-Driver.com/go/plug-and-play
Manufacturer
CT-Concept Technologie AG
Intelligent Power Electronic s
Renferst ra sse 15
CH-2504 Biel-Bienne
Switzerland
Tel. +41 - 32 - 344 47 47
Fax +41 - 32 - 344 47 40
E-mail Info@IGBT-Driver.com
Internet www.IGBT-Driver.com
© Copyr ight 19 99… 20 11 by CT-Concept Technologie AG - Switzerland. All rights reserved.
We reserve the right to make any technical modifications without prior notice. Version from 2016-05-20
