MAX 3000A Programmable Logic Device Family (R) June 2006, ver. 3.5 Features... Data Sheet High-performance, low-cost CMOS EEPROM-based programmable logic devices (PLDs) built on a MAX(R) architecture (see Table 1) 3.3-V in-system programmability (ISP) through the built-in IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface with advanced pin-locking capability - ISP circuitry compliant with IEEE Std. 1532 Built-in boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990 Enhanced ISP features: - Enhanced ISP algorithm for faster programming - ISP_Done bit to ensure complete programming - Pull-up resistor on I/O pins during in-system programming High-density PLDs ranging from 600 to 10,000 usable gates 4.5-ns pin-to-pin logic delays with counter frequencies of up to 227.3 MHz MultiVoltTM I/O interface enabling the device core to run at 3.3 V, while I/O pins are compatible with 5.0-V, 3.3-V, and 2.5-V logic levels Pin counts ranging from 44 to 256 in a variety of thin quad flat pack (TQFP), plastic quad flat pack (PQFP), plastic J-lead chip carrier (PLCC), and FineLine BGATM packages Hot-socketing support Programmable interconnect array (PIA) continuous routing structure for fast, predictable performance Industrial temperature range Table 1. MAX 3000A Device Features EPM3032A EPM3064A EPM3128A EPM3256A EPM3512A Usable gates Feature 600 1,250 2,500 5,000 10,000 Macrocells 32 64 128 256 512 Logic array blocks 2 4 8 16 32 Maximum user I/O pins 34 66 98 161 208 tPD (ns) 4.5 4.5 5.0 7.5 7.5 tSU (ns) 2.9 2.8 3.3 5.2 5.6 tCO1 (ns) 3.0 3.1 3.4 4.8 4.7 227.3 222.2 192.3 126.6 116.3 fCNT (MHz) Altera Corporation DS-MAX3000A-3.5 1 MAX 3000A Programmable Logic Device Family Data Sheet ...and More Features General Description 2 PCI compatible Bus-friendly architecture including programmable slew-rate control Open-drain output option Programmable macrocell flipflops with individual clear, preset, clock, and clock enable controls Programmable power-saving mode for a power reduction of over 50% in each macrocell Configurable expander product-term distribution, allowing up to 32 product terms per macrocell Programmable security bit for protection of proprietary designs Enhanced architectural features, including: - 6 or 10 pin- or logic-driven output enable signals - Two global clock signals with optional inversion - Enhanced interconnect resources for improved routability - Programmable output slew-rate control Software design support and automatic place-and-route provided by Altera's development systems for Windows-based PCs and Sun SPARCstations, and HP 9000 Series 700/800 workstations Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), Verilog HDL, VHDL, and other interfaces to popular EDA tools from third-party manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, and VeriBest Programming support with the Altera master programming unit (MPU), MasterBlasterTM communications cable, ByteBlasterMVTM parallel port download cable, BitBlasterTM serial download cable as well as programming hardware from third-party manufacturers and any in-circuit tester that supports JamTM Standard Test and Programming Language (STAPL) Files (.jam), Jam STAPL Byte-Code Files (.jbc), or Serial Vector Format Files (.svf) MAX 3000A devices are low-cost, high-performance devices based on the Altera MAX architecture. Fabricated with advanced CMOS technology, the EEPROM-based MAX 3000A devices operate with a 3.3-V supply voltage and provide 600 to 10,000 usable gates, ISP, pin-to-pin delays as fast as 4.5 ns, and counter speeds of up to 227.3 MHz. MAX 3000A devices in the -4, -5, -6, -7, and -10 speed grades are compatible with the timing requirements of the PCI Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2. See Table 2. Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 2. MAX 3000A Speed Grades Device Speed Grade -4 -7 -10 v v v v v v EPM3256A v v EPM3512A v v EPM3032A v EPM3064A v -5 -6 v EPM3128A The MAX 3000A architecture supports 100% transistor-to-transistor logic (TTL) emulation and high-density small-scale integration (SSI), medium-scale integration (MSI), and large-scale integration (LSI) logic functions. The MAX 3000A architecture easily integrates multiple devices ranging from PALs, GALs, and 22V10s to MACH and pLSI devices. MAX 3000A devices are available in a wide range of packages, including PLCC, PQFP, and TQFP packages. See Table 3. Table 3. MAX 3000A Maximum User I/O Pins Device 44-Pin PLCC 44-Pin TQFP EPM3032A 34 34 EPM3064A 34 34 EPM3128A EPM3256A EPM3512A Note (1) 100-Pin 144-Pin 208-Pin 256-Pin TQFP TQFP PQFP FineLine BGA 66 80 96 116 98 158 161 172 208 Note: (1) When the IEEE Std. 1149.1 (JTAG) interface is used for in-system programming or boundary-scan testing, four I/O pins become JTAG pins. MAX 3000A devices use CMOS EEPROM cells to implement logic functions. The user-configurable MAX 3000A architecture accommodates a variety of independent combinatorial and sequential logic functions. The devices can be reprogrammed for quick and efficient iterations during design development and debugging cycles, and can be programmed and erased up to 100 times. Altera Corporation 3 MAX 3000A Programmable Logic Device Family Data Sheet MAX 3000A devices contain 32 to 512 macrocells, combined into groups of 16 macrocells called logic array blocks (LABs). Each macrocell has a programmable-AND/fixed-OR array and a configurable register with independently programmable clock, clock enable, clear, and preset functions. To build complex logic functions, each macrocell can be supplemented with shareable expander and high-speed parallel expander product terms to provide up to 32 product terms per macrocell. MAX 3000A devices provide programmable speed/power optimization. Speed-critical portions of a design can run at high speed/full power, while the remaining portions run at reduced speed/low power. This speed/power optimization feature enables the designer to configure one or more macrocells to operate at 50% or lower power while adding only a nominal timing delay. MAX 3000A devices also provide an option that reduces the slew rate of the output buffers, minimizing noise transients when non-speed-critical signals are switching. The output drivers of all MAX 3000A devices can be set for 2.5 V or 3.3 V, and all input pins are 2.5-V, 3.3-V, and 5.0-V tolerant, allowing MAX 3000A devices to be used in mixed-voltage systems. MAX 3000A devices are supported by Altera development systems, which are integrated packages that offer schematic, text--including VHDL, Verilog HDL, and the Altera Hardware Description Language (AHDL)--and waveform design entry, compilation and logic synthesis, simulation and timing analysis, and device programming. The software provides EDIF 2 0 0 and 3 0 0, LPM, VHDL, Verilog HDL, and other interfaces for additional design entry and simulation support from other industry-standard PC- and UNIX-workstation-based EDA tools. The software runs on Windows-based PCs, as well as Sun SPARCstation, and HP 9000 Series 700/800 workstations. f Functional Description For more information on development tools, see the MAX+PLUS II Programmable Logic Development System & Software Data Sheet and the Quartus Programmable Logic Development System & Software Data Sheet. The MAX 3000A architecture includes the following elements: Logic array blocks (LABs) Macrocells Expander product terms (shareable and parallel) Programmable interconnect array (PIA) I/O control blocks The MAX 3000A architecture includes four dedicated inputs that can be used as general-purpose inputs or as high-speed, global control signals (clock, clear, and two output enable signals) for each macrocell and I/O pin. Figure 1 shows the architecture of MAX 3000A devices. 4 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 1. MAX 3000A Device Block Diagram INPUT/GCLK1 INPUT/OE2/GCLK2 INPUT/OE1 INPUT/GCLRn 6 or 10 Output Enables (1) 6 or 10 Output Enables (1) LAB B LAB A 2 to 16 I/O I/O Control Block 2 to 16 36 Macrocells 1 to 16 36 16 LAB C 2 to 16 I/O I/O Control Block 2 to 16 Macrocells 33 to 48 16 6 or 10 2 to 16 2 to 16 I/O Control Block 2 to 16 I/O 6 or 10 LAB D PIA 36 2 to 16 16 2 to 16 6 or 10 Macrocells 17 to 32 36 Macrocells 49 to 64 2 to 16 I/O Control Block 2 to 16 I/O 16 2 to 16 6 or 10 Note: (1) EPM3032A, EPM3064A, EPM3128A, and EPM3256A devices have six output enables. EPM3512A devices have 10 output enables. Logic Array Blocks The MAX 3000A device architecture is based on the linking of high-performance LABs. LABs consist of 16-macrocell arrays, as shown in Figure 1. Multiple LABs are linked together via the PIA, a global bus that is fed by all dedicated input pins, I/O pins, and macrocells. Each LAB is fed by the following signals: Altera Corporation 36 signals from the PIA that are used for general logic inputs Global controls that are used for secondary register functions 5 MAX 3000A Programmable Logic Device Family Data Sheet Macrocells MAX 3000A macrocells can be individually configured for either sequential or combinatorial logic operation. Macrocells consist of three functional blocks: logic array, product-term select matrix, and programmable register. Figure 2 shows a MAX 3000A macrocell. Figure 2. MAX 3000A Macrocell Global Clear LAB Local Array Parallel Logic Expanders (from other macrocells) Global Clocks 2 Programmable Register Register Bypass PRN D/T Q Clock/ Enable Select ProductTerm Select Matrix To I/O Control Block ENA CLRN VCC Clear Select Shared Logic Expanders 36 Signals from PIA To PIA 16 Expander Product Terms Combinatorial logic is implemented in the logic array, which provides five product terms per macrocell. The product-term select matrix allocates these product terms for use as either primary logic inputs (to the OR and XOR gates) to implement combinatorial functions, or as secondary inputs to the macrocell's register preset, clock, and clock enable control functions. Two kinds of expander product terms ("expanders") are available to supplement macrocell logic resources: Shareable expanders, which are inverted product terms that are fed back into the logic array Parallel expanders, which are product terms borrowed from adjacent macrocells The Altera development system automatically optimizes product-term allocation according to the logic requirements of the design. 6 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet For registered functions, each macrocell flipflop can be individually programmed to implement D, T, JK, or SR operation with programmable clock control. The flipflop can be bypassed for combinatorial operation. During design entry, the designer specifies the desired flipflop type; the Altera development system software then selects the most efficient flipflop operation for each registered function to optimize resource utilization. Each programmable register can be clocked in three different modes: Global clock signal mode, which achieves the fastest clock-to-output performance. Global clock signal enabled by an active-high clock enable. A clock enable is generated by a product term. This mode provides an enable on each flipflop while still achieving the fast clock-to-output performance of the global clock. Array clock implemented with a product term. In this mode, the flipflop can be clocked by signals from buried macrocells or I/O pins. Two global clock signals are available in MAX 3000A devices. As shown in Figure 1, these global clock signals can be the true or the complement of either of the two global clock pins, GCLK1 or GCLK2. Each register also supports asynchronous preset and clear functions. As shown in Figure 2, the product-term select matrix allocates product terms to control these operations. Although the product-term-driven preset and clear from the register are active high, active-low control can be obtained by inverting the signal within the logic array. In addition, each register clear function can be individually driven by the active-low dedicated global clear pin (GCLRn). All registers are cleared upon power-up. By default, all registered outputs drive low when the device is powered up. You can set the registered outputs to drive high upon power-up through the Quartus(R) II software. Quartus II software uses the NOT Gate Push-Back method, which uses an additional macrocell to set the output high. To set this in the Quartus II software, go to the Assignment Editor and set the Power-Up Level assignment for the register to High. Altera Corporation 7 MAX 3000A Programmable Logic Device Family Data Sheet Expander Product Terms Although most logic functions can be implemented with the five product terms available in each macrocell, highly complex logic functions require additional product terms. Another macrocell can be used to supply the required logic resources. However, the MAX 3000A architecture also offers both shareable and parallel expander product terms ("expanders") that provide additional product terms directly to any macrocell in the same LAB. These expanders help ensure that logic is synthesized with the fewest possible logic resources to obtain the fastest possible speed. Shareable Expanders Each LAB has 16 shareable expanders that can be viewed as a pool of uncommitted single product terms (one from each macrocell) with inverted outputs that feed back into the logic array. Each shareable expander can be used and shared by any or all macrocells in the LAB to build complex logic functions. Shareable expanders incur a small delay (tSEXP). Figure 3 shows how shareable expanders can feed multiple macrocells. Figure 3. MAX 3000A Shareable Expanders Shareable expanders can be shared by any or all macrocells in an LAB. Macrocell Product-Term Logic Product-Term Select Matrix Macrocell Product-Term Logic 36 Signals from PIA 8 16 Shared Expanders Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Parallel Expanders Parallel expanders are unused product terms that can be allocated to a neighboring macrocell to implement fast, complex logic functions. Parallel expanders allow up to 20 product terms to directly feed the macrocell OR logic, with five product terms provided by the macrocell and 15 parallel expanders provided by neighboring macrocells in the LAB. The Altera development system compiler can automatically allocate up to three sets of up to five parallel expanders to the macrocells that require additional product terms. Each set of five parallel expanders incurs a small, incremental timing delay (tPEXP). For example, if a macrocell requires 14 product terms, the compiler uses the five dedicated product terms within the macrocell and allocates two sets of parallel expanders; the first set includes five product terms, and the second set includes four product terms, increasing the total delay by 2 x tPEXP. Two groups of eight macrocells within each LAB (e.g., macrocells 1 through 8 and 9 through 16) form two chains to lend or borrow parallel expanders. A macrocell borrows parallel expanders from lower- numbered macrocells. For example, macrocell 8 can borrow parallel expanders from macrocell 7, from macrocells 7 and 6, or from macrocells 7, 6, and 5. Within each group of eight, the lowest-numbered macrocell can only lend parallel expanders and the highest-numbered macrocell can only borrow them. Figure 4 shows how parallel expanders can be borrowed from a neighboring macrocell. Altera Corporation 9 MAX 3000A Programmable Logic Device Family Data Sheet Figure 4. MAX 3000A Parallel Expanders Unused product terms in a macrocell can be allocated to a neighboring macrocell. From Previous Macrocell Preset Producter Select Matrix Macrocell ProductTerm Logic Clock Clear Preset ProductT m Ter Select Matrix Macrocell ProductTerm Logic Clock Clear 36 Signals from PIA To Next Macrocell 16 Shared Expanders Programmable Interconnect Array Logic is routed between LABs on the PIA. This global bus is a programmable path that connects any signal source to any destination on the device. All MAX 3000A dedicated inputs, I/O pins, and macrocell outputs feed the PIA, which makes the signals available throughout the entire device. Only the signals required by each LAB are actually routed from the PIA into the LAB. Figure 5 shows how the PIA signals are routed into the LAB. An EEPROM cell controls one input to a two-input AND gate, which selects a PIA signal to drive into the LAB. 10 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 5. MAX 3000A PIA Routing To LAB PIA Signals While the routing delays of channel-based routing schemes in masked or FPGAs are cumulative, variable, and path-dependent, the MAX 3000A PIA has a predictable delay. The PIA makes a design's timing performance easy to predict. I/O Control Blocks The I/O control block allows each I/O pin to be individually configured for input, output, or bidirectional operation. All I/O pins have a tri-state buffer that is individually controlled by one of the global output enable signals or directly connected to ground or VCC. Figure 6 shows the I/O control block for MAX 3000A devices. The I/O control block has 6 or 10 global output enable signals that are driven by the true or complement of two output enable signals, a subset of the I/O pins, or a subset of the I/O macrocells. Altera Corporation 11 MAX 3000A Programmable Logic Device Family Data Sheet Figure 6. I/O Control Block of MAX 3000A Devices 6 or 10 Global Output Enable Signals (1) PIA OE Select Multiplexer VCC to Other I/O Pins from Macrocell GND Open-Drain Output Slew-Rate Control to PIA Note: (1) EPM3032A, EPM3064A, EPM3128A, and EPM3256A devices have six output enables. EPM3512A devices have 10 output enables. When the tri-state buffer control is connected to ground, the output is tri-stated (high impedance), and the I/O pin can be used as a dedicated input. When the tri-state buffer control is connected to VCC, the output is enabled. The MAX 3000A architecture provides dual I/O feedback, in which macrocell and pin feedbacks are independent. When an I/O pin is configured as an input, the associated macrocell can be used for buried logic. 12 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet In-System Programmability MAX 3000A devices can be programmed in-system via an industry- standard four-pin IEEE Std. 1149.1-1990 (JTAG) interface. In-system programmability (ISP) offers quick, efficient iterations during design development and debugging cycles. The MAX 3000A architecture internally generates the high programming voltages required to program its EEPROM cells, allowing in-system programming with only a single 3.3-V power supply. During in-system programming, the I/O pins are tri-stated and weakly pulled-up to eliminate board conflicts. The pull-up value is nominally 50 k. MAX 3000A devices have an enhanced ISP algorithm for faster programming. These devices also offer an ISP_Done bit that ensures safe operation when in-system programming is interrupted. This ISP_Done bit, which is the last bit programmed, prevents all I/O pins from driving until the bit is programmed. ISP simplifies the manufacturing flow by allowing devices to be mounted on a printed circuit board (PCB) with standard pick-and-place equipment before they are programmed. MAX 3000A devices can be programmed by downloading the information via in-circuit testers, embedded processors, the MasterBlaster communications cable, the ByteBlasterMV parallel port download cable, and the BitBlaster serial download cable. Programming the devices after they are placed on the board eliminates lead damage on high-pin-count packages (e.g., QFP packages) due to device handling. MAX 3000A devices can be reprogrammed after a system has already shipped to the field. For example, product upgrades can be performed in the field via software or modem. The Jam STAPL programming and test language can be used to program MAX 3000A devices with in-circuit testers, PCs, or embedded processors. f For more information on using the Jam STAPL programming and test language, see Application Note 88 (Using the Jam Language for ISP & ICR via an Embedded Processor), Application Note 122 (Using Jam STAPL for ISP & ICR via an Embedded Processor) and AN 111 (Embedded Programming Using the 8051 and Jam Byte-Code). The ISP circuitry in MAX 3000A devices is compliant with the IEEE Std. 1532 specification. The IEEE Std. 1532 is a standard developed to allow concurrent ISP between multiple PLD vendors. Altera Corporation 13 MAX 3000A Programmable Logic Device Family Data Sheet Programming Sequence During in-system programming, instructions, addresses, and data are shifted into the MAX 3000A device through the TDI input pin. Data is shifted out through the TDO output pin and compared against the expected data. Programming a pattern into the device requires the following six ISP stages. A stand-alone verification of a programmed pattern involves only stages 1, 2, 5, and 6. 1. Enter ISP. The enter ISP stage ensures that the I/O pins transition smoothly from user mode to ISP mode. The enter ISP stage requires 1 ms. 2. Check ID. Before any program or verify process, the silicon ID is checked. The time required to read this silicon ID is relatively small compared to the overall programming time. 3. Bulk Erase. Erasing the device in-system involves shifting in the instructions to erase the device and applying one erase pulse of 100 ms. 4. Program. Programming the device in-system involves shifting in the address and data and then applying the programming pulse to program the EEPROM cells. This process is repeated for each EEPROM address. 5. Verify. Verifying an Altera device in-system involves shifting in addresses, applying the read pulse to verify the EEPROM cells, and shifting out the data for comparison. This process is repeated for each EEPROM address. 6. Exit ISP. An exit ISP stage ensures that the I/O pins transition smoothly from ISP mode to user mode. The exit ISP stage requires 1 ms. Programming Times The time required to implement each of the six programming stages can be broken into the following two elements: 14 A pulse time to erase, program, or read the EEPROM cells. A shifting time based on the test clock (TCK) frequency and the number of TCK cycles to shift instructions, address, and data into the device. Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet By combining the pulse and shift times for each of the programming stages, the program or verify time can be derived as a function of the TCK frequency, the number of devices, and specific target device(s). Because different ISP-capable devices have a different number of EEPROM cells, both the total fixed and total variable times are unique for a single device. Programming a Single MAX 3000A Device The time required to program a single MAX 3000A device in-system can be calculated from the following formula: t PROG = t PPULSE Cycle PTCK+ ------------------------------f TCK = Programming time = Sum of the fixed times to erase, program, and verify the EEPROM cells CyclePTCK = Number of TCK cycles to program a device = TCK frequency fTCK where: tPROG tPPULSE The ISP times for a stand-alone verification of a single MAX 3000A device can be calculated from the following formula: Cycle VTCK t VER = t VPULSE + -------------------------------f TCK = Verify time where: tVER = Sum of the fixed times to verify the EEPROM cells tVPULSE CycleVTCK = Number of TCK cycles to verify a device Altera Corporation 15 MAX 3000A Programmable Logic Device Family Data Sheet The programming times described in Tables 4 through 6 are associated with the worst-case method using the enhanced ISP algorithm. Table 4. MAX 3000A tPULSE & CycleTCK Values Device Programming tPPULSE (s) Stand-Alone Verification CyclePTCK tVPULSE (s) CycleVTCK EPM3032A 2.00 55,000 0.002 18,000 EPM3064A 2.00 105,000 0.002 35,000 EPM3128A 2.00 205,000 0.002 68,000 EPM3256A 2.00 447,000 0.002 149,000 EPM3512A 2.00 890,000 0.002 297,000 Tables 5 and 6 show the in-system programming and stand alone verification times for several common test clock frequencies. Table 5. MAX 3000A In-System Programming Times for Different Test Clock Frequencies Device fTCK Units 10 MHz 5 MHz 2 MHz 1 MHz 500 kHz 200 kHz 100 kHz 50 kHz EPM3032A 2.01 2.01 2.03 2.06 2.11 2.28 2.55 3.10 s EPM3064A 2.01 2.02 2.05 2.11 2.21 2.53 3.05 4.10 s EPM3128A 2.02 2.04 2.10 2.21 2.41 3.03 4.05 6.10 s EPM3256A 2.05 2.09 2.23 2.45 2.90 4.24 6.47 10.94 s EPM3512A 2.09 2.18 2.45 2.89 3.78 6.45 10.90 19.80 s Table 6. MAX 3000A Stand-Alone Verification Times for Different Test Clock Frequencies Device 16 Units fTCK 10 MHz 5 MHz 2 MHz 1 MHz 500 kHz 200 kHz 100 kHz 50 kHz EPM3032A 0.00 0.01 0.01 0.02 0.04 0.09 0.18 0.36 s EPM3064A 0.01 0.01 0.02 0.04 0.07 0.18 0.35 0.70 s EPM3128A 0.01 0.02 0.04 0.07 0.14 0.34 0.68 1.36 s EPM3256A 0.02 0.03 0.08 0.15 0.30 0.75 1.49 2.98 s EPM3512A 0.03 0.06 0.15 0.30 0.60 1.49 2.97 5.94 s Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Programming with External Hardware MAX 3000A devices can be programmed on Windows-based PCs with an Altera Logic Programmer card, MPU, and the appropriate device adapter. The MPU performs continuity checking to ensure adequate electrical contact between the adapter and the device. f For more information, see the Altera Programming Hardware Data Sheet. The Altera software can use text- or waveform-format test vectors created with the Altera Text Editor or Waveform Editor to test the programmed device. For added design verification, designers can perform functional testing to compare the functional device behavior with the results of simulation. Data I/O, BP Microsystems, and other programming hardware manufacturers also provide programming support for Altera devices. f IEEE Std. 1149.1 (JTAG) Boundary-Scan Support For more information, see Programming Hardware Manufacturers. MAX 3000A devices include the JTAG BST circuitry defined by IEEE Std. 1149.1-1990. Table 7 describes the JTAG instructions supported by MAX 3000A devices. The pin-out tables found on the Altera web site (http://www.altera.com) or the Altera Digital Library show the location of the JTAG control pins for each device. If the JTAG interface is not required, the JTAG pins are available as user I/O pins. Table 7. MAX 3000A JTAG Instructions JTAG Instruction Description SAMPLE/PRELOAD Allows a snapshot of signals at the device pins to be captured and examined during normal device operation, and permits an initial data pattern output at the device pins EXTEST Allows the external circuitry and board-level interconnections to be tested by forcing a test pattern at the output pins and capturing test results at the input pins BYPASS Places the 1-bit bypass register between the TDI and TDO pins, which allows the BST data to pass synchronously through a selected device to adjacent devices during normal device operation IDCODE Selects the IDCODE register and places it between the TDI and TDO pins, allowing the IDCODE to be serially shifted out of TDO USERCODE Selects the 32-bit USERCODE register and places it between the TDI and TDO pins, allowing the USERCODE value to be shifted out of TDO ISP Instructions These instructions are used when programming MAX 3000A devices via the JTAG ports with the MasterBlaster, ByteBlasterMV, or BitBlaster cable, or when using a Jam STAPL file, JBC file, or SVF file via an embedded processor or test equipment Altera Corporation 17 MAX 3000A Programmable Logic Device Family Data Sheet The instruction register length of MAX 3000A devices is 10 bits. The IDCODE and USERCODE register length is 32 bits. Tables 8 and 9 show the boundary-scan register length and device IDCODE information for MAX 3000A devices. Table 8. MAX 3000A Boundary-Scan Register Length Device Boundary-Scan Register Length EPM3032A 96 EPM3064A 192 EPM3128A 288 EPM3256A 480 EPM3512A 624 Table 9. 32-Bit MAX 3000A Device IDCODE Value Device Note (1) IDCODE (32 bits) Version (4 Bits) Part Number (16 Bits) Manufacturer's 1 (1 Bit) Identity (11 Bits) (2) EPM3032A 0001 0111 0000 0011 0010 00001101110 1 EPM3064A 0001 0111 0000 0110 0100 00001101110 1 EPM3128A 0001 0111 0001 0010 1000 00001101110 1 EPM3256A 0001 0111 0010 0101 0110 00001101110 1 EPM3512A 0001 0111 0101 0001 0010 00001101110 1 Notes: (1) (2) f 18 The most significant bit (MSB) is on the left. The least significant bit (LSB) for all JTAG IDCODEs is 1. See Application Note 39 (IEEE 1149.1 (JTAG) Boundary-Scan Testing in Altera Devices) for more information on JTAG BST. Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 7 shows the timing information for the JTAG signals. Figure 7. MAX 3000A JTAG Waveforms TMS TDI t JCP t JCH t JCL t JPSU t JPH TCK tJPZX t JPXZ t JPCO TDO tJSH tJSSU Signal to Be Captured Signal to Be Driven tJSCO tJSZX tJSXZ Table 10 shows the JTAG timing parameters and values for MAX 3000A devices. Table 10. JTAG Timing Parameters & Values for MAX 3000A Devices Symbol Altera Corporation Parameter tJCP TCK clock period tJCH TCK clock high time tJCL tJPSU Min Max Unit 100 ns 50 ns TCK clock low time 50 ns JTAG port setup time 20 ns tJPH JTAG port hold time 45 ns tJPCO JTAG port clock to output 25 ns tJPZX JTAG port high impedance to valid output 25 ns tJPXZ JTAG port valid output to high impedance 25 tJSSU Capture register setup time 20 tJSH Capture register hold time 45 tJSCO Update register clock to output 25 ns tJSZX Update register high impedance to valid output 25 ns tJSXZ Update register valid output to high impedance 25 ns ns ns ns 19 MAX 3000A Programmable Logic Device Family Data Sheet Programmable Speed/Power Control MAX 3000A devices offer a power-saving mode that supports low-power operation across user-defined signal paths or the entire device. This feature allows total power dissipation to be reduced by 50% or more because most logic applications require only a small fraction of all gates to operate at maximum frequency. The designer can program each individual macrocell in a MAX 3000A device for either high-speed or low-power operation. As a result, speed-critical paths in the design can run at high speed, while the remaining paths can operate at reduced power. Macrocells that run at low power incur a nominal timing delay adder (tLPA) for the tLAD, tLAC, tIC, tACL, tEN, tCPPW and tSEXP parameters. Output Configuration MAX 3000A device outputs can be programmed to meet a variety of system-level requirements. MultiVolt I/O Interface The MAX 3000A device architecture supports the MultiVolt I/O interface feature, which allows MAX 3000A devices to connect to systems with differing supply voltages. MAX 3000A devices in all packages can be set for 2.5-V, 3.3-V, or 5.0-V I/O pin operation. These devices have one set of VCC pins for internal operation and input buffers (VCCINT), and another set for I/O output drivers (VCCIO). The VCCIO pins can be connected to either a 3.3-V or 2.5-V power supply, depending on the output requirements. When the VCCIO pins are connected to a 2.5-V power supply, the output levels are compatible with 2.5-V systems. When the VCCIO pins are connected to a 3.3-V power supply, the output high is at 3.3 V and is therefore compatible with 3.3-V or 5.0-V systems. Devices operating with VCCIO levels lower than 3.0 V incur a nominally greater timing delay of tOD2 instead of tOD1. Inputs can always be driven by 2.5-V, 3.3-V, or 5.0-V signals. Table 11 summarizes the MAX 3000A MultiVolt I/O support. Table 11. MAX 3000A MultiVolt I/O Support VCCIO Voltage Input Signal (V) Output Signal (V) 2.5 3.3 5.0 2.5 2.5 v v v v 3.3 v v v v 3.3 5.0 v v Note: (1) 20 When VCCIO is 3.3 V, a MAX 3000A device can drive a 2.5-V device that has 3.3-V tolerant inputs. Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Open-Drain Output Option MAX 3000A devices provide an optional open-drain (equivalent to open-collector) output for each I/O pin. This open-drain output enables the device to provide system-level control signals (e.g., interrupt and write enable signals) that can be asserted by any of several devices. It can also provide an additional wired-OR plane. Open-drain output pins on MAX 3000A devices (with a pull-up resistor to the 5.0-V supply) can drive 5.0-V CMOS input pins that require a high VIH. When the open-drain pin is active, it will drive low. When the pin is inactive, the resistor will pull up the trace to 5.0 V, thereby meeting CMOS requirements. The open-drain pin will only drive low or tri-state; it will never drive high. The rise time is dependent on the value of the pull-up resistor and load impedance. The IOL current specification should be considered when selecting a pull-up resistor Slew-Rate Control The output buffer for each MAX 3000A I/O pin has an adjustable output slew rate that can be configured for low-noise or high-speed performance. A faster slew rate provides high-speed transitions for high-performance systems. However, these fast transitions may introduce noise transients into the system. A slow slew rate reduces system noise, but adds a nominal delay of 4 to 5 ns. When the configuration cell is turned off, the slew rate is set for low-noise performance. Each I/O pin has an individual EEPROM bit that controls the slew rate, allowing designers to specify the slew rate on a pin-by-pin basis. The slew rate control affects both the rising and falling edges of the output signal. Design Security All MAX 3000A devices contain a programmable security bit that controls access to the data programmed into the device. When this bit is programmed, a design implemented in the device cannot be copied or retrieved. This feature provides a high level of design security because programmed data within EEPROM cells is invisible. The security bit that controls this function, as well as all other programmed data, is reset only when the device is reprogrammed. Generic Testing MAX 3000A devices are fully tested. Complete testing of each programmable EEPROM bit and all internal logic elements ensures 100% programming yield. AC test measurements are taken under conditions equivalent to those shown in Figure 8. Test patterns can be used and then erased during early stages of the production flow. Altera Corporation 21 MAX 3000A Programmable Logic Device Family Data Sheet Figure 8. MAX 3000A AC Test Conditions Power supply transients can affect AC measurements. Simultaneous transitions of multiple outputs should be avoided for accurate measurement. Threshold tests must not be performed under AC conditions. Large-amplitude, fast- ground-current transients normally occur as the device outputs discharge the load capacitances. When these transients flow through the parasitic inductance between the device ground pin and the test system ground, significant reductions in observable noise immunity can result. Numbers in brackets are for 2.5-V outputs. Numbers without brackets are for 3.3-V devices or outputs. Operating Conditions 703 [521 ] Device Output To Test System 620 [481 ] C1 (includes jig capacitance) Device input rise and fall times < 2 ns Tables 12 through 15 provide information on absolute maximum ratings, recommended operating conditions, DC operating conditions, and capacitance for MAX 3000A devices. Table 12. MAX 3000A Device Absolute Maximum Ratings Symbol VCC Parameter Note (1) Min Max Unit -0.5 4.6 V DC input voltage -2.0 5.75 V IOUT DC output current, per pin -25 25 mA TSTG Storage temperature No bias -65 150 C TA Ambient temperature Under bias -65 135 C TJ Junction temperature PQFP and TQFP packages, under bias 135 C VCC Supply voltage VI 22 Conditions With respect to ground (2) Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 13. MAX 3000A Device Recommended Operating Conditions Symbol Parameter Conditions Min Max Unit VCCINT Supply voltage for internal logic and (10) input buffers 3.0 3.6 V VCCIO Supply voltage for output drivers, 3.3-V operation 3.0 3.6 V Supply voltage for output drivers, 2.5-V operation 2.3 2.7 V VCCISP Supply voltage during ISP VI Input voltage VO Output voltage TA Ambient temperature TJ Junction temperature tR Input rise time tF Input fall time (3) Commercial range Industrial range Commercial range Industrial range (11) Table 14. MAX 3000A Device DC Operating Conditions Symbol Parameter 3.0 3.6 V -0.5 5.75 V 0 VCCIO V 0 70 C -40 85 C 0 90 C -40 105 C 40 ns 40 ns Note (4) Min Max Unit VIH High-level input voltage 1.7 5.75 V VIL Low-level input voltage -0.5 0.8 VOH 3.3-V high-level TTL output voltage IOH = -8 mA DC, VCCIO = 3.00 V (5) 3.3-V high-level CMOS output voltage 2.5-V high-level output voltage VOL Conditions V 2.4 V IOH = -0.1 mA DC, VCCIO = 3.00 V (5) VCCIO - 0.2 V IOH = -100 A DC, VCCIO = 2.30 V (5) 2.1 V IOH = -1 mA DC, VCCIO = 2.30 V (5) 2.0 V IOH = -2 mA DC, VCCIO = 2.30 V (5) 1.7 V 3.3-V low-level TTL output voltage IOL = 8 mA DC, VCCIO = 3.00 V (6) 3.3-V low-level CMOS output IOL = 0.1 mA DC, VCCIO = 3.00 V (6) voltage 0.4 V 0.2 V 2.5-V low-level output voltage II Input leakage current IOZ RI S P IOL = 100 A DC, VCCIO = 2.30 V (6) 0.2 V IOL = 1 mA DC, VCCIO = 2.30 V (6) 0.4 V IOL = 2 mA DC, VCCIO = 2.30 V (6) 0.7 V 10 A VI = -0.5 to 5.5 V (7) -10 Tri-state output off-state current VI = -0.5 to 5.5 V (7) -10 10 A Value of I/O pin pull-up resistor when programming in-system or during power-up VC C I O = 2.3 to 3.6 V (8) 20 74 k Altera Corporation 23 MAX 3000A Programmable Logic Device Family Data Sheet Table 15. MAX 3000A Device Capacitance Symbol Parameter Note (9) Conditions Min Max Unit CIN Input pin capacitance VIN = 0 V, f = 1.0 MHz 8 pF CI/O I/O pin capacitance VOUT = 0 V, f = 1.0 MHz 8 pF Notes to tables: (1) (2) See the Operating Requirements for Altera Devices Data Sheet. Minimum DC input voltage is -0.5 V. During transitions, the inputs may undershoot to -2.0 V or overshoot to 5.75 V for input currents less than 100 mA and periods shorter than 20 ns. (3) All pins, including dedicated inputs, I/O pins, and JTAG pins, may be driven before VCCINT and VCCIO are powered. (4) These values are specified under the recommended operating conditions, as shown in Table 13 on page 23. (5) The parameter is measured with 50% of the outputs each sourcing the specified current. The IOH parameter refers to high-level TTL or CMOS output current. (6) The parameter is measured with 50% of the outputs each sinking the specified current. The IOL parameter refers to low-level TTL, PCI, or CMOS output current. (7) This value is specified during normal device operation. During power-up, the maximum leakage current is 300 A. (8) This pull-up exists while devices are programmed in-system and in unprogrammed devices during power-up. (9) Capacitance is measured at 25 C and is sample-tested only. The OE1 pin (high-voltage pin during programming) has a maximum capacitance of 20 pF. (10) The POR time for all MAX 3000A devices does not exceed 100 s. The sufficient VCCINT voltage level for POR is 3.0 V. The device is fully initialized within the POR time after VCCINT reaches the sufficient POR voltage level. (11) These devices support in-system programming for -40 to 100 C. For in-system programming support between -40 and 0 C, contact Altera Applications. Figure 9 shows the typical output drive characteristics of MAX 3000A devices. 24 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 9. Output Drive Characteristics of MAX 3000A Devices 3.3 V 150 IOL 100 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 3.3 V O Temperature = 25 C 50 IOH 0 0 1 2 3 4 VO Output Voltage (V) 2.5 V 150 IOL 100 Typical IO Output Current (mA) VCCINT = 3.3 V VCCIO = 2.5 V O Temperature = 25 C 50 IOH 0 0 1 2 3 4 VO Output Voltage (V) Power Sequencing & Hot-Socketing Because MAX 3000A devices can be used in a mixed-voltage environment, they have been designed specifically to tolerate any possible power-up sequence. The VCCIO and VCCINT power planes can be powered in any order. Signals can be driven into MAX 3000A devices before and during power-up without damaging the device. In addition, MAX 3000A devices do not drive out during power-up. Once operating conditions are reached, MAX 3000A devices operate as specified by the user. Altera Corporation 25 MAX 3000A Programmable Logic Device Family Data Sheet Timing Model MAX 3000A device timing can be analyzed with the Altera software, with a variety of popular industry-standard EDA simulators and timing analyzers, or with the timing model shown in Figure 10. MAX 3000A devices have predictable internal delays that enable the designer to determine the worst-case timing of any design. The software provides timing simulation, point-to-point delay prediction, and detailed timing analysis for device-wide performance evaluation. Figure 10. MAX 3000A Timing Model Internal Output Enable Delay t IOE Global Control Delay t GLOB Input Delay t IN PIA Delay t PIA Logic Array Delay t LAD Register Control Delay t LAC tIC t EN Shared Expander Delay t SEXP Parallel Expander Delay t PEXP Register Delay t SU tH t PRE t CLR t RD t COMB Output Delay t OD1 t OD2 t OD3 t XZ t Z X1 t Z X2 t Z X3 I/O Delay tI O The timing characteristics of any signal path can be derived from the timing model and parameters of a particular device. External timing parameters, which represent pin-to-pin timing delays, can be calculated as the sum of internal parameters. Figure 11 shows the timing relationship between internal and external delay parameters. 26 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 11. MAX 3000A Switching Waveforms tR & tF < 2 ns. Inputs are driven at 3 V for a logic high and 0 V for a logic low. All timing characteristics are measured at 1.5 V. Combinatorial Mode tIN Input Pin tIO I/O Pin tPIA PIA Delay tSEXP Shared Expander Delay tLAC , tLAD Logic Array Input tPEXP Parallel Expander Delay tCOMB Logic Array Output tOD Output Pin Global Clock Mode Global Clock Pin tR tCH tIN Global Clock at Register tSU tCL tF tACL tF tGLOB tH Data or Enable (Logic Array Output) Array Clock Mode tR tACH Input or I/O Pin tIN tIO Clock into PIA Clock into Logic Array Clock at Register tPIA tIC tSU tH Data from Logic Array tRD tPIA tPIA tCLR , tPRE Register to PIA to Logic Array tOD tOD Register Output to Pin Altera Corporation 27 MAX 3000A Programmable Logic Device Family Data Sheet Tables 16 through 23 show EPM3032A, EPM3064A, EPM3128A, EPM3256A, and EPM3512A timing information. Table 16. EPM3032A External Timing Parameters Symbol Parameter Note (1) Conditions Speed Grade -4 Min Unit -7 Max Min -10 Max Min Max tPD1 Input to non- registered output C1 = 35 pF (2) 4.5 7.5 10 ns tPD2 I/O input to non- registered output C1 = 35 pF (2) 4.5 7.5 10 ns tSU Global clock setup time (2) tH Global clock hold time (2) 0.0 tCO1 Global clock to output C1 = 35 pF delay 1.0 tCH Global clock high time 2.0 3.0 4.0 ns tCL Global clock low time 2.0 3.0 4.0 ns tASU Array clock setup time (2) 1.6 2.5 3.6 ns tAH Array clock hold time (2) 0.3 0.5 0.5 tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 tACH Array clock high time tACL Array clock low time tCPPW Minimum pulse width for clear and preset tCNT Minimum global clock (2) period fCNT Maximum internal (2), (4) global clock frequency tACNT Minimum array clock period fACNT Maximum internal (2), (4) array clock frequency 28 (3) 2.9 4.7 6.3 0.0 3.0 4.3 1.0 1.0 ns 0.0 5.0 7.2 1.0 1.0 ns 6.7 ns ns 9.4 ns 2.0 3.0 4.0 2.0 3.0 4.0 ns 2.0 3.0 4.0 ns 4.4 227.3 (2) 7.2 138.9 4.4 227.3 9.7 103.1 7.2 138.9 ns MHz 9.7 103.1 ns ns MHz Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 17. EPM3032A Internal Timing Parameters (Part 1 of 2) Symbol Parameter Note (1) Conditions Speed Grade -4 Min Unit -7 Max Min -10 Max Min Max tIN Input pad and buffer delay 0.7 1.2 1.5 ns tIO I/O input pad and buffer delay 0.7 1.2 1.5 ns tSEXP Shared expander delay 1.9 3.1 4.0 ns tPEXP Parallel expander delay 0.5 0.8 1.0 ns tLAD Logic array delay 1.5 2.5 3.3 ns tLAC Logic control array delay 0.6 1.0 1.2 ns tIOE Internal output enable delay 0.0 0.0 0.0 ns tOD1 Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 0.8 1.3 1.8 ns tOD2 Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 1.3 1.8 2.3 ns tOD3 Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF 5.8 6.3 6.8 ns tZX1 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V 4.0 4.0 5.0 ns tZX2 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V 4.5 4.5 5.5 ns tZX3 Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V 9.0 9.0 10.0 ns tXZ Output buffer disable delay C1 = 5 pF 5.0 ns tSU Register setup time 1.3 2.0 2.8 ns tH Register hold time 0.6 1.0 1.3 ns tRD Register delay 0.7 1.2 1.5 ns tCOMB Combinatorial delay 0.6 1.0 1.3 ns tIC Array clock delay 1.2 2.0 2.5 ns tEN Register enable time 0.6 1.0 1.2 ns tGLOB Global control delay 0.8 1.3 1.9 ns tPRE Register preset time 1.2 1.9 2.6 ns tCLR Register clear time 1.2 1.9 2.6 ns Altera Corporation 4.0 4.0 29 MAX 3000A Programmable Logic Device Family Data Sheet Table 17. EPM3032A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Note (1) Conditions Speed Grade -4 Min Unit -7 Max Min -10 Max Min Max tPIA PIA delay (2) 0.9 1.5 2.1 ns tLPA Low-power adder (5) 2.5 4.0 5.0 ns Table 18. EPM3064A External Timing Parameters Symbol Parameter Note (1) Conditions Speed Grade -4 Min Unit -7 Max Min -10 Max Min Max tPD1 Input to non-registered output C1 = 35 pF (2) 4.5 7.5 10.0 ns tPD2 I/O input to non-registered C1 = 35 pF (2) output 4.5 7.5 10.0 ns tSU Global clock setup time (2) tH Global clock hold time (2) tCO1 Global clock to output delay C1 = 35 pF 1.0 tCH Global clock high time 2.0 3.0 4.0 ns tCL Global clock low time 2.0 3.0 4.0 ns tASU Array clock setup time (2) 1.6 2.6 3.6 ns tAH Array clock hold time (2) 0.3 tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 2.8 4.7 0.0 6.2 0.0 3.1 1.0 0.0 5.1 0.4 4.3 1.0 ns 1.0 ns 7.0 0.6 7.2 1.0 ns ns 9.6 ns tACH Array clock high time 2.0 3.0 4.0 ns tACL Array clock low time 2.0 3.0 4.0 ns tCPPW Minimum pulse width for clear and preset (3) 2.0 3.0 4.0 ns tCNT Minimum global clock period (2) fCNT Maximum internal global clock frequency (2), (4) tACNT Minimum array clock period (2) fACNT Maximum internal array clock frequency 30 (2), (4) 4.5 222.2 7.4 135.1 4.5 222.2 10.0 100.0 7.4 135.1 MHz 10.0 100.0 ns ns MHz Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 19. EPM3064A Internal Timing Parameters (Part 1 of 2) Symbol Parameter Note (1) Conditions Speed Grade -4 Min Unit -7 Max Min -10 Max Min Max tIN Input pad and buffer delay 0.6 1.1 1.4 ns tIO I/O input pad and buffer delay 0.6 1.1 1.4 ns tSEXP Shared expander delay 1.8 3.0 3.9 ns tPEXP Parallel expander delay 0.4 0.7 0.9 ns tLAD Logic array delay 1.5 2.5 3.2 ns tLAC Logic control array delay 0.6 1.0 1.2 ns tIOE Internal output enable delay 0.0 0.0 0.0 ns tOD1 Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 0.8 1.3 1.8 ns tOD2 Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 1.3 1.8 2.3 ns tOD3 Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF 5.8 6.3 6.8 ns tZX1 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V 4.0 4.0 5.0 ns tZX2 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V 4.5 4.5 5.5 ns tZX3 Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V 9.0 9.0 10.0 ns tXZ Output buffer disable delay C1 = 5 pF tSU Register setup time 1.3 tH Register hold time 0.6 tRD Register delay 0.7 1.2 1.6 ns tCOMB Combinatorial delay 0.6 0.9 1.3 ns tIC Array clock delay 1.2 1.9 2.5 ns tEN Register enable time 0.6 1.0 1.2 ns tGLOB Global control delay 1.0 1.5 2.2 ns tPRE Register preset time 1.3 2.1 2.9 ns Altera Corporation 4.0 4.0 2.0 5.0 2.9 1.0 ns ns 1.3 ns 31 MAX 3000A Programmable Logic Device Family Data Sheet Table 19. EPM3064A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Note (1) Conditions Speed Grade -4 Min tCLR Register clear time tPIA PIA delay tLPA Low-power adder Parameter -7 Max Min -10 Max Min Max 1.3 2.1 2.9 ns (2) 1.0 1.7 2.3 ns (5) 3.5 4.0 5.0 ns Table 20. EPM3128A External Timing Parameters Symbol Unit Note (1) Conditions Speed Grade -5 Min Unit -7 Max Min -10 Max Min Max tPD1 Input to non- registered output C1 = 35 pF (2) 5.0 7.5 10 ns tPD2 I/O input to non- registered output C1 = 35 pF (2) 5.0 7.5 10 ns tSU Global clock setup time (2) tH Global clock hold time (2) 0.0 tCO1 Global clock to output C1 = 35 pF delay 1.0 tCH Global clock high time 2.0 3.0 4.0 ns tCL Global clock low time 2.0 3.0 4.0 ns tASU Array clock setup time (2) 1.8 2.8 3.8 ns tAH Array clock hold time (2) 0.2 0.3 0.4 tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 tACH Array clock high time tACL Array clock low time tCPPW Minimum pulse width for clear and preset tCNT Minimum global clock (2) period fCNT Maximum internal (2), (4) global clock frequency tACNT Minimum array clock period 32 (3) (2) 3.3 4.9 6.6 0.0 3.4 4.9 1.0 1.0 ns 0.0 5.0 7.1 1.0 1.0 ns 6.6 ns ns 9.4 ns 2.0 3.0 4.0 2.0 3.0 4.0 ns 2.0 3.0 4.0 ns 5.2 192.3 7.7 129.9 5.2 ns 10.2 98.0 7.7 ns MHz 10.2 ns Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 20. EPM3128A External Timing Parameters Symbol Parameter Note (1) Conditions Speed Grade -5 Min fACNT Maximum internal (2), (4) array clock frequency -7 Max 192.3 Min Parameter -10 Max 129.9 Table 21. EPM3128A Internal Timing Parameters (Part 1 of 2) Symbol Unit Min Max 98.0 MHz Note (1) Conditions Speed Grade -5 Min Unit -7 Max Min -10 Max Min Max tIN Input pad and buffer delay 0.7 1.0 1.4 ns tIO I/O input pad and buffer delay 0.7 1.0 1.4 ns tSEXP Shared expander delay 2.0 2.9 3.8 ns tPEXP Parallel expander delay 0.4 0.7 0.9 ns tLAD Logic array delay 1.6 2.4 3.1 ns tLAC Logic control array delay 0.7 1.0 1.3 ns tIOE Internal output enable delay 0.0 0.0 0.0 ns tOD1 Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 0.8 1.2 1.6 ns tOD2 Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 1.3 1.7 2.1 ns tOD3 Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF 5.8 6.2 6.6 ns tZX1 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 3.3 V 4.0 4.0 5.0 ns tZX2 Output buffer enable delay, C1 = 35 pF slow slew rate = off VCCIO = 2.5 V 4.5 4.5 5.5 ns tZX3 Output buffer enable delay, C1 = 35 pF slow slew rate = on VCCIO = 2.5 V or 3.3 V 9.0 9.0 10.0 ns tXZ Output buffer disable delay C1 = 5 pF 4.0 4.0 5.0 ns Altera Corporation 33 MAX 3000A Programmable Logic Device Family Data Sheet Table 21. EPM3128A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Note (1) Conditions Speed Grade -5 Min Unit -7 Max Min -10 Max Max Register setup time 1.4 tH Register hold time 0.6 tRD Register delay 0.8 1.2 1.6 ns tCOMB Combinatorial delay 0.5 0.9 1.3 ns tIC Array clock delay 1.2 1.7 2.2 ns tEN Register enable time 0.7 1.0 1.3 ns tGLOB Global control delay 1.1 1.6 2.0 ns tPRE Register preset time 1.4 2.0 2.7 ns tCLR Register clear time 1.4 2.0 2.7 ns tPIA PIA delay (2) 1.4 2.0 2.6 ns tLPA Low-power adder (5) 4.0 4.0 5.0 ns Table 22. EPM3256A External Timing Parameters Symbol Parameter 2.1 Min tSU 2.9 1.0 ns 1.3 ns Note (1) Conditions Speed Grade -7 Min Unit -10 Max Min Max tPD1 Input to non-registered output C1 = 35 pF (2) 7.5 10 ns tPD2 I/O input to non-registered C1 = 35 pF (2) output 7.5 10 ns tSU Global clock setup time (2) 5.2 6.9 ns tH Global clock hold time (2) 0.0 0.0 ns tCO1 Global clock to output delay C1 = 35 pF 1.0 tCH Global clock high time tCL Global clock low time tASU Array clock setup time (2) tAH Array clock hold time (2) tACO1 Array clock to output delay C1 = 35 pF (2) 1.0 tACH Array clock high time 3.0 4.0 ns tACL Array clock low time 3.0 4.0 ns tCPPW Minimum pulse width for clear and preset 3.0 4.0 ns 34 (3) 4.8 1.0 6.4 ns 3.0 4.0 ns 3.0 4.0 ns 2.7 3.6 ns 0.3 0.5 7.3 1.0 ns 9.7 ns Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 22. EPM3256A External Timing Parameters Symbol Parameter Note (1) Conditions Speed Grade -7 Min tCNT Minimum global clock period (2) fCNT Maximum internal global clock frequency (2), (4) tACNT Minimum array clock period (2) fACNT Maximum internal array clock frequency (2), (4) Parameter -10 Max Min Max 7.9 10.5 126.6 95.2 10.5 126.6 ns MHz 7.9 Table 23. EPM3256A Internal Timing Parameters (Part 1 of 2) Symbol Unit 95.2 ns MHz Note (1) Conditions Speed Grade -7 Min Unit -10 Max Min Max tIN Input pad and buffer delay 0.9 1.2 ns tIO I/O input pad and buffer delay 0.9 1.2 ns tSEXP Shared expander delay 2.8 3.7 ns tPEXP Parallel expander delay 0.5 0.6 ns tLAD Logic array delay 2.2 2.8 ns tLAC Logic control array delay 1.0 1.3 ns tIOE Internal output enable delay 0.0 0.0 ns tOD1 Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 1.2 1.6 ns tOD2 Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 1.7 2.1 ns tOD3 Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF 6.2 6.6 ns tZX1 Output buffer enable delay, slow C1 = 35 pF slew rate = off VCCIO = 3.3 V 4.0 5.0 ns tZX2 Output buffer enable delay, slow C1 = 35 pF slew rate = off VCCIO = 2.5 V 4.5 5.5 ns Altera Corporation 35 MAX 3000A Programmable Logic Device Family Data Sheet Table 23. EPM3256A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Note (1) Conditions Speed Grade -7 Min Unit -10 Max Min Max tZX3 Output buffer enable delay, slow C1 = 35 pF slew rate = on VCCIO = 2.5 V or 3.3 V tXZ Output buffer disable delay tSU Register setup time 2.1 2.9 ns tH Register hold time 0.9 1.2 ns tRD Register delay 1.2 1.6 ns tCOMB Combinatorial delay 0.8 1.2 ns tIC Array clock delay 1.6 2.1 ns tEN Register enable time 1.0 1.3 ns tGLOB Global control delay 1.5 2.0 ns tPRE Register preset time 2.3 3.0 ns tCLR Register clear time 2.3 3.0 ns tPIA PIA delay (2) 2.4 3.2 ns tLPA Low-power adder (5) 4.0 5.0 ns C1 = 5 pF Table 24. EPM3512A External Timing Parameters Symbol Parameter 9.0 10.0 4.0 5.0 ns ns Note (1) Conditions Speed Grade -7 Min Unit -10 Max Min Max tPD1 Input to non-registered output C1 = 35 pF (2) 7.5 10.0 ns tPD2 I/O input to non-registered output C1 = 35 pF (2) 7.5 10.0 ns tSU Global clock setup time (2) 5.6 7.6 ns tH Global clock hold time (2) 0.0 0.0 ns tFSU Global clock setup time of fast input 3.0 3.0 ns tFH Global clock hold time of fast input 0.0 0.0 ns tCO1 Global clock to output delay tCH Global clock high time 3.0 4.0 tCL Global clock low time 3.0 4.0 ns tASU Array clock setup time 2.5 3.5 ns 36 C1 = 35 pF (2) 1.0 4.7 1.0 6.3 ns ns Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Table 24. EPM3512A External Timing Parameters Symbol Parameter Note (1) Conditions Speed Grade -7 Min tAH Array clock hold time (2) C1 = 35 pF (2) tACO1 Array clock to output delay tACH Array clock high time tACL Array clock low time tCPPW Minimum pulse width for clear and preset (3) tCNT Minimum global clock period (2) fCNT Maximum internal global clock frequency (2), (4) tACNT Minimum array clock period (2) fACNT Maximum internal array clock frequency (2), (4) Parameter -10 Max 0.2 Min Max 0.3 1.0 7.8 ns 1.0 10.4 ns 3.0 4.0 ns 3.0 4.0 ns 3.0 4.0 ns 8.6 116.3 11.5 87.0 11.5 ns 87.0 MHz Speed Grade Unit Note (1) Conditions -7 Min ns MHz 8.6 116.3 Table 25. EPM3512A Internal Timing Parameters (Part 1 of 2) Symbol Unit -10 Max Min Max tIN Input pad and buffer delay 0.7 0.9 ns tIO I/O input pad and buffer delay 0.7 0.9 ns tFIN Fast input delay 3.1 3.6 ns tSEXP Shared expander delay 2.7 3.5 ns tPEXP Parallel expander delay 0.4 0.5 ns tLAD Logic array delay 2.2 2.8 ns tLAC Logic control array delay 1.0 1.3 ns tIOE Internal output enable delay 0.0 0.0 ns tOD1 Output buffer and pad delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 1.0 1.5 ns tOD2 Output buffer and pad delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 1.5 2.0 ns Altera Corporation 37 MAX 3000A Programmable Logic Device Family Data Sheet Table 25. EPM3512A Internal Timing Parameters (Part 2 of 2) Symbol Parameter Note (1) Conditions Speed Grade -7 Min Unit -10 Max Min Max tOD3 Output buffer and pad delay, slow slew rate = on VCCIO = 2.5 V or 3.3 V C1 = 35 pF 6.0 6.5 ns tZX1 Output buffer enable delay, slow slew rate = off VCCIO = 3.3 V C1 = 35 pF 4.0 5.0 ns tZX2 Output buffer enable delay, slow slew rate = off VCCIO = 2.5 V C1 = 35 pF 4.5 5.5 ns tZX3 Output buffer enable delay, slow slew rate = on VCCIO = 3.3 V C1 = 35 pF 9.0 10.0 ns tXZ Output buffer disable delay C1 = 5 pF 5.0 ns tSU Register setup time tH Register hold time 0.6 0.8 ns tFSU Register setup time of fast input 1.6 1.6 ns tFH Register hold time of fast input 1.4 tRD Register delay 1.3 1.7 ns tCOMB Combinatorial delay 0.6 0.8 ns tIC Array clock delay 1.8 2.3 ns tEN Register enable time 1.0 1.3 ns tGLOB Global control delay 1.7 2.2 ns tPRE Register preset time 1.0 1.4 ns tCLR Register clear time 1.0 1.4 ns tPIA PIA delay (2) 3.0 4.0 ns tLPA Low-power adder (5) 4.5 5.0 ns 4.0 2.1 3.0 ns 1.4 ns Notes to tables: (1) (2) (3) (4) (5) 38 These values are specified under the recommended operating conditions, as shown in Table 13 on page 23. See Figure 11 on page 27 for more information on switching waveforms. These values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these devices, add an additional 0.1 ns to the PIA timing value. This minimum pulse width for preset and clear applies for both global clear and array controls. The tLPA parameter must be added to this minimum width if the clear or reset signal incorporates the tLAD parameter into the signal path. These parameters are measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB. The tLPA parameter must be added to the tLAD, tLAC, tIC, tEN, tSEXP, tACL, and tCPPW parameters for macrocells running in low-power mode. Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Power Consumption Supply power (P) versus frequency (fMAX, in MHz) for MAX 3000A devices is calculated with the following equation: P = PINT + PIO = ICCINT x VCC + PIO The PIO value, which depends on the device output load characteristics and switching frequency, can be calculated using the guidelines given in Application Note 74 (Evaluating Power for Altera Devices). The ICCINT value depends on the switching frequency and the application logic. The ICCINT value is calculated with the following equation: ICCINT = (A x MCTON) + [B x (MCDEV - MCTON)] + (C x MCUSED x fMAX x togLC) The parameters in the ICCINT equation are: MCTON MCDEV MCUSED fMAX togLC A, B, C = Number of macrocells with the Turbo BitTM option turned on, as reported in the Quartus II or MAX+PLUS II Report File (.rpt) = Number of macrocells in the device = Total number of macrocells in the design, as reported in the RPT File = Highest clock frequency to the device = Average percentage of logic cells toggling at each clock (typically 12.5%) = Constants (shown in Table 26) Table 26. MAX 3000A ICC Equation Constants Device A B C EPM3032A 0.71 0.30 0.014 EPM3064A 0.71 0.30 0.014 EPM3128A 0.71 0.30 0.014 EPM3256A 0.71 0.30 0.014 EPM3512A 0.71 0.30 0.014 The ICCINT calculation provides an ICC estimate based on typical conditions using a pattern of a 16-bit, loadable, enabled, up/down counter in each LAB with no output load. Actual ICC should be verified during operation because this measurement is sensitive to the actual pattern in the device and the environmental operating conditions. Figures 12 and 13 show the typical supply current versus frequency for MAX 3000A devices. Altera Corporation 39 MAX 3000A Programmable Logic Device Family Data Sheet Figure 12. ICC vs. Frequency for MAX 3000A Devices EPM3064A EPM3032A 40 80 VCC = 3.3 V Room Temperature 35 227.3 MHz 30 222.2 MHz 60 High Speed 25 Typical ICC Active (mA) VCC = 3.3 V Room Temperature 70 20 144.9 MHz 15 High Speed 50 Typical ICC Active (mA) 40 30 125.0 MHz 20 10 Low Power Low Power 10 5 0 50 100 150 200 250 Frequency (MHz) 0 50 100 1 50 200 250 Frequency (MHz) EPM3128A 160 VCC = 3.3 V Room Temperature 140 192.3 MHz 120 High Speed 100 Typical ICC Active (mA) 80 60 108.7 MHz 40 Low Power 20 0 50 100 150 200 250 Frequency (MHz) 40 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 13. ICC vs. Frequency for MAX 3000A Devices EPM3512A EPM3256A 600 300 VCC = 3.3 V Room Temperature 250 VCC = 3.3 V Room Temperature 500 172.4 MHz 116.3 MHz 200 Typical ICC Active (mA) 400 High Speed Typical ICC Active (mA) 150 High Speed 300 102.0 MHz 100 76.3 MHz 200 Low Power 50 Low Power 100 0 50 100 1 50 Frequency (MHz) Altera Corporation 200 0 20 40 60 80 100 120 140 Frequency (MHz) 41 MAX 3000A Programmable Logic Device Family Data Sheet Device Pin-Outs See the Altera web site (http://www.altera.com) or the Altera Digital Library for pin-out information. Figures 14 through 18 show the package pin-out diagrams for MAX 3000A devices. Figure 14. 44-Pin PLCC/TQFP Package Pin-Out Diagram I/O/TDI 7 39 I/O I/O 8 38 I/O/TDO I/O 9 37 I/O GND 10 36 GND I/O 11 35 VCC I/O 12 34 I/O I/O/TMS 13 33 I/O I/O 14 32 I/O/TCK VCC 15 31 I/O I/O 16 30 GND GND 17 29 I/O EPM3032A EPM3064A I/O I/O GND INPUT/GCLK1 INPUT/OE1 INPUT/GCLRn INPUT/OE2/GCLK2 VCC I/O I/O Pin 1 I/O I/O I/O 1 44 43 42 41 40 GND 2 INPUT/GCLK1 INPUT/OE2/GCLK2 3 INPUT/OE1 5 4 INPUT/GCLRn 6 VCC I/O I/O I/O Package outlines not drawn to scale. Pin 34 I/O I/O/TDI I/O I/O/TDO I/O I/O GND GND VCC I/O EPM3032A EPM3064A I/O I/O/TMS I/O I/O I/O I/O/TCK VCC I/O I/O GND GND I/O 44-Pin PLCC 42 I/O I/O I/O I/O I/O VCC GND I/O I/O I/O Pin 12 I/O I/O I/O I/O I/O I/O VCC GND I/O I/O I/O I/O 18 19 20 21 22 23 24 25 26 27 28 Pin 23 44-Pin TQFP Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 15. 100-Pin TQFP Package Pin-Out Diagram Package outline not drawn to scale. Pin 76 Pin 1 EPM3064A EPM3128A Pin 26 Pin 51 Figure 16. 144-Pin TQFP Package Pin-Out Diagram Package outline not drawn to scale. Indicates location of Pin 1 Pin 1 Pin 109 EPM3128A EPM3256A Pin 37 Altera Corporation Pin 73 43 MAX 3000A Programmable Logic Device Family Data Sheet Figure 17. 208-Pin PQFP Package Pin-Out Diagram Package outline not drawn to scale. Pin 1 Pin 157 EPM3256A EPM3512A Pin 53 44 Pin 105 Altera Corporation MAX 3000A Programmable Logic Device Family Data Sheet Figure 18. 256-Pin FineLine BGA Package Pin-Out Diagram Package outline not drawn to scale. A1 Ball Pad Corner A Indicates Location of Ball A1 B C D E F G H EPM3512A J K L M N P R T 16 15 14 13 12 11 10 Revision History 9 8 7 6 5 4 3 2 1 The information contained in the MAX 3000A Programmable Logic Device Data Sheet version 3.5 supersedes information published in previous versions. The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.5: Version 3.5 The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.5: New paragraph added before "Expander Product Terms". Version 3.4 The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.4: Altera Corporation Updated Table 1. 45 MAX 3000A Programmable Logic Device Family Data Sheet Version 3.3 The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.3: Updated Tables 3, 13, and 26. Added Tables 4 through 6. Updated Figures 12 and 13. Added "Programming Sequence" on page 14 and "Programming Times" on page 14 Version 3.2 The following change were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.2: Updated the EPM3512 ICC versus frequency graph in Figure 13. Version 3.1 The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.1: Updated timing information in Table 1 for the EPM3256A device. Updated Note (10) of Table 15. Version 3.0 The following changes were made in the MAX 3000A Programmable Logic Device Data Sheet version 3.0: 101 Innovation Drive San Jose, CA 95134 (408) 544-7000 http://www.altera.com Applications Hotline: (800) 800-EPLD Customer Marketing: (408) 544-7104 Literature Services: lit_req@altera.com 46 Added EPM3512A device. Updated Tables 2 and 3. Copyright (c) 2006 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services Altera Corporation