Preliminary SF2030A (R) * * * * Designed for PHS BTS IF Applications Excellent Size-to Performance Ratio Hermetic 11.5 X 4.0 mm Surface-Mount Case Complies with Directive 2002/95/EC (RoHS) 243.95 MHz SAW Filter Pb Maximum Ratings Value Units Operating Temperature Range Rating -15 to +80 C Storage Temperature Range -40 to +85 C Maximum DC Voltage 30 V Maximum Source Power +15 dBm Maximum Soldering Profile SM1154-14 260C for 30sec Electrical Characteristics Characteristic Nominal Frequency Nominal Insertion Attenuation Pass band width at 3 dB (Relative to Fn) Point of left side Point of right side Amplitude Ripple (peak-valley) FN - 110 kHz ---- Fn + 110kHz Group Delay Ripple FN - 110 kHz ---- Fn + 110kHz Relative Attenuation (Relative to Fn) Fn - 21.6 MHz Fn - 21.4 MHz Fn - 10.8 MHz Fn - 1.2 MHz Fn - 0.7 MHz Fn - 0.6 MHz Fn - 0.5 MHz Fn + 0.5 MHz Fn + 0.6 MHz Fn + 0.7 MHz Fn + 1.2 MHz Fn + 10.8 MHz Lid Symbolization (YY=year, WW=week, S=shift) See note 4 Sym fN Notes Min Typ 243.95 Max 5 Units MHz dB -150 kHz 1.0 dB 0.5 sec B3dB +150 0.6 60 60 55 30 30 30 15 15 30 30 30 55 RFM SF2030A YYWWS dB dB dB dB dB dB dB dB dB dB dB dB Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. "LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes." The design, manufacturing process, and specifications of this filter are subject to change. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. US and international patents may apply. RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc. (c)Copyright 1999, RF Monolithics Inc. Electrostatic Sensitive Device. Observe precautions for handling. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 1 243.95 MHz SAW Filter 23 Oct 2007 10:46:35 CH1 S11 1 U FS 1 : 62 . 482 9 . 6777 243 . 950 000 MHz SF2030A 6 . 3138 CH3 S22 1 : 47 . 762 243 . 950 000 nH 1 U FS 1 . 4551 MHz 1 949 . 30 pH 1 Cor Cor Full CENTR CH2 243 . 950 S21 MHz LOG SPAN 10 . 000 10 dB/ MHz CENTR REF -10 dB 243 . 950 1 : 0 . 0000 MHz dB SPAN 0 . 000 10 . 000 000 MHz MHz 1 CH2 Max Cor 3 2 BW : 4 Full cent : Markers REF=1 . 483040 MHz 243 . 955294 MHz Q: 505 . 04 1_ loss CENTER 243 . 950 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SPAN 10 . 000 000 : -3 . 7998 dB MHz E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 2 243.95 MHz SAW Filter SF2030A Demo schematic C1 P1 3.1pF SF2030A C2 P2 R1 240 2.7pF L1 43nH R2 0 240 L2 0 51nH 0 0 15 Dec 2004 10:01:44 CH1 S21 LOG 5 dB/ REF -10 dB 1 : -7 . 7068 dB 243 . 950 000 MHz 1 Cor PRm CH2 S21 DEL 50 ns/ REF 1.8 us 1 : 0 . 0000 s 0 . 000 000 MHz CH2 Smo Markers REF=1 2 : 10 . 872 ns -144 . 000 kHz Cor 1 3 3 : 45 . 700 3 144 . 000 2 ns kHz PRm START 242 . 950 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. STOP 244 . 950 000 MHz E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 3 243.95 MHz SAW Filter 15 Dec 2004 10:04:38 CH1 S21 LOG 10 dB/ REF 0 dB PRm Cor CENTER 243 . 950 000 MHz RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. SPAN 20 . 000 000 MHz E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 4 243.95 MHz SAW Filter SM1154-14 Case 14-Terminal Ceramic Surface-Mount Case 11.5 x 4.0 mm Nominal Footprint Case Dimensions Dimension A B C D E F G H mm Nom 11.5 4.0 1.6 1.5 0.76 1.27 1.27 0.1 Max 11.6 4.2 1.8 1.7 Min .442 .150 .057 .053 Inches Nom 0.450 0.157 0.063 0.059 0.030 0.050 0.050 0.004 Max 0.458 .166 .069 .065 Electrical Connections Materials Solder Pad Termination Au plating 30 - 60 inches (76.2-152 m) over 80200 inches (203-508 m) Ni. Lid Fe-Ni-Co Alloy Electroless Nickel Plate (8-11% Phosphorus) 100-200 inches Thick Body Min 11.4 3.8 1.4 1.3 Connection Terminals Input Al2O3 Ceramic 2 Output 9 Ground All Others Pb Free G E C 7 7 8 9 6 6 9 10 5 5 10 11 4 4 11 12 3 3 12 13 2 2 13 14 1 1 14 F 8 A 0.334 REF. (8.48) 0.067 TYP. (1.70) B 0.050 TYP. (1.27) 0.190 (4.84) 0.034 TYP. (0.86) Recommended PCB Footprint H RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. D E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 5 243.95 MHz SAW Filter COMPONENT ORIENTATION and DIMENSIONS 4.0 mm 0.1 1.5 mm +0.1 -0.0 2.0 mm 0.1 1.75 mm 0.1 PIN #1 W (CARRIER TAPE SIZE) BO 1.5 mm +0.3 -0.0 P (PITCH) AO USER DIRECTION OF FEED COVER TAPE SIZE KO COVER TAPE Carrier Tape Dimensions Ao 4.55 mm 0.1 Bo 12.04 mm 0.1 Ko 2.13 mm 0.1 Pitch 8.00 mm 0.1 W 24.00 mm 0.3 RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 6 243.95 MHz SAW Filter Leader and Trailer specifications (Based upon EIA-481) Dimensions of the leader and trailer 7 Inch Reel Quantity 500 Symbol Dimension A N +0 -4 178 60 C 1 D +0.5 -0.2 13 B +1.5 -0 20.2 2 W1 0.5 W2 +2 -0 24.4 30.4 MAX 13 Inch Reel Quantity 2000 Symbol Dimension A 330 N +0 -4 100 C 2 13 D +0.5 -0.2 20.2 B +1.5 -0 2 W1 0.5 24.4 W2 +2 -0 30.4 MAX Dimensional drawing of the reel RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 7 243.95 MHz SAW Filter Additional items (1) Cover tape peeling strength The cover tape shall be adhered evenly to the carrier tape along both sides in the pulling direction. The cover tape peeling strength shall be as follows for an angle between the cover tape and the pulling direction of 165 to 180 (see the figure) and a peeling speed of 300mm/min. 10mm/min. [EIA-481] 0.1N to 1.3N for a tape width of 12 to 56mm Fixing method 1. Insert the tip of the carrier tape into the groove. 2. Fix the tip of the cover tape with adhesive tape. Tape material (1) Carrier tape [anti-charging treatment: carbon used] Surface resistivity: 1 x 108 or less Material: Polystyrene or Polycarbonate (2) Cover tape material: Polyester (anti-charging treated) Surface resistivity: 1 x 1012 or less t = 50 to 100m Warranty periods Cover tape peeling strength and mounting performance of stored components. 2-1. Cover tape peeling strength: One year after delivery (Peeling strength: 0.1N to 1.3N) Number of missing components There shall not be two or more consecutive missing components. Also, the maximum number of missing components shall be the larger of one piece or 0.1%. Storage environment Keep the product on which taping has been performed to a temperature below 40C and a humidity within 80% RH. Do not subject in the direct sun. RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 8 243.95 MHz SAW Filter RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 9 243.95 MHz SAW Filter Package for Shipment 7 Inch Reel 13 Inch Reel Quanity Per Reel Number Reels Per Carton External Caton Dimensions Reel Weight Shipping Carton Weight Total Weight 500 4 254 x 254 x 127 mm 10 x 10 x 5 inches 896 g 448 g 1344 g 500 10 254 x 254 x 203 mm 10 x 10 x 8 inches 2240 g 448 g 2688 g Quanity Per Reel Number Reels Per Carton External Caton Dimensions Reel Weight Shipping Carton Weight Total Weight 2000 2 356 x 356 x 102 mm 14 x 14 x 4 inches 1288 g 448 g 1736 g 2000 4 356 x 356 x 178 mm 14 x 14 x 7 inches 2576 g 448 g 3024 g 2000 8 356 x 356 x 356 mm 14 x 14 x 14 inches 5152 g 448 g 5600 g RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 10 243.95 MHz SAW Filter RFM Qualification and Reliability Test Test Standard Test Parameters 1 Life at Elevated Temperature MIL-STD-202 Method 108 Condition C 1,000 Hours 125C Unbiased 2 Temperature Cycling JESD22 Method JA-104 Air-to-Air -55 xCto +125 xC 20 min. Dwell 1,000 cycles 3 Vibration, Variable Frequency MIL-STD-883 Method 2007 Condition B 50g Max. 4 Cycles, 3 Axis 20 Hz to 2 kHz to 20 Hz 4 Mechanical Shock MIL-STD-883 Method 2002 Condition B 1,500g Max. 5 Shocks 3 Axis 5 Destructive Bond Strength MIL-STD-883 Method 2011 Condition C Wire Bond Pull Strength 2.0 grams (After Seal) 6 Die Shear Strength MIL-STD-883 Method 2019 Shear Strength 0.6 kg (Strength/area limit in development) 7 Solderability (Note 2) J-STD-002 Method B 8 hr. steam age 245 x C solder temperature 5 second dwell >95% wetted surface 8 Physical Dimensions JESD22 Method JB-100 Critical Dimensions Within specifications 9 Temperature Characteristics RFM Procedure Frequency over Temperature Within specifications 10 Terminal Strength (Note 2) MIL-STD-833 Method 2004 Condition A & D Cond. A-Lead Tension Cond. B -Pad Adhesionr 24 8 oz. - 30 sec. Visual Requirements & meets Hermetic Spec. 11 Resistance to Solvents MIL-STD-883 Method 2015 Solvents a, b, d Visual Requirements 12 Steady State Life MIL-STD-883 Method 1005 1,000 Hours Max. Operating Temperature Rated Voltage Within Electrical & Hermetic Spec. (Note 1) 13 Internal WaterVapor Content MIL-STD-883 Method 1018 < 5,001 PPM 14 Constant Acceleration MIL-STD-883 Method 2001 Y1 Direction 30,000g Within Electrical & Hermetic Spec. (Note 1) 15 Substrate Attach Strength MIL-STD-883 Method 2027 Tensile Strength of Die Attachment Custom per Device RF Monolithics, Inc. Phone: (972) 233-2903 Fax: (972) 387-8148 RFM Europe Phone: 44 1963 251383 Fax: 44 1963 251510 (c)1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc. Pass / Fail Criteria Within Electrical & Hermetic Spec. (Note 1) E-mail: info@rfm.com http://www.rfm.com SF2030A-10/25/07 Page 11