Metal Film, Cylindrical Resistors
www.vishay.com For Technical questions contact: ff3bresistors@vishay.com Document Number: 20006
42 Revision: 15-Feb-06
PMM0204 NOT FOR NEW DESIGNS
Vishay Draloric
FEATURES
•Stable metal film on high quality ceramic
•Very low TC and tight tolerances
•Excellent stability at different environmental conditions
•Pure tin termination on nickel barrier, plated on press fit
steel caps
•Compatible with lead (Pb)-free and lead containing
soldering processes
•Lead (Pb)-free and RoHS compliant
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
POWER RATING1)
P70
W
LIMITING ELEMENT
VOLTAGE2)
DC or AC rms
V
TEMPERATURE
COEFFICIENT
ppm/K
TOLERANCE
%
RESISTANCE
RANGE
Ω
E-SERIES
PMM0204 0.125 100 ± 5 ± 0.1; ± 0.25 100R - 100K 96 - 192
PMM0204 0.125 100 ± 10 ± 0.1; ± 0.25 100R - 221K 96 - 192
PMM0204 0.125 100 ± 15 ± 0.1; ± 0.25 100R - 221K 96 - 192
PMM0204 0.125 100 ± 25 ± 0.1; ± 0.25 100R - 221K 96 - 192
PMM0204 0.125 100 ± 50 ± 0.1; ± 0.25 100R - 221K 96 - 192
1) Permissible dissipation depends on the maximum temperature at
the solder point, the component placement density and the
substrate material.
2) Rated voltage: .
•TC ≤ 10 ppm/°C: temperature range is - 10 °C to + 85 °C
• Without TC-band, TC marking on label only
• Marking: According to IEC 60062; see also datasheet “surface
mount resistor marking” (document number: 20020)
PxR
3) Based on measurements on test board acc. to EN 140400.
TECHNICAL SPECIFICATIONS
PARAMETER UNIT PMM0204
Rated Dissipation at 70 °C W 0.125
Limiting Element Voltage, DC or AC rms V 100
Insulation Voltage (1 min), DC or AC peak V 200
Thermal Resistance3) K/W ≤ 220
Insulation Resistance Ω≥ 10 10
Category Temperature Range °C - 10 to + 100
Failure Rate 10-9/h < 1
Weight/1000 pcs g 18
Document Number: 20006 For Technical questions contact: ff3bresistors@vishay.com www.vishay.com
Revision: 15-Feb-06 43
PMM0204
Metal Film Cylindrical Resistors Vishay Draloric
DIMENSIONS
* d measured in the middle of the resistor
MODEL
DIMENSIONS [in millimeters]
Dmax d* L Amax Amin
PMM0204 1.4 D - 0.15 3.6 - 0.15 0.85 0.5
MODEL
SOLDER PAD DIMENSIONS
[in millimeters]
REFLOW SOLDERING WAVE SOLDERING
ab l abl
PMM0204 1.0 1.6 2.2 1.2 1.6 2.2
Note
1. Products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER.
2. The PART NUMBER is shown to facilitate the introduction of a unified part numbering system. Currently, this PART NUMBER is applicable
in the Americas only.
3. Please refer to table PACKING, see below.
PART NUMBER AND PRODUCT DESCRIPTION1)
PART NUMBER2): PMM02040E5620CB0
MODEL/SIZE SPECIAL CHARACTER TC VALUE TOLERANCE PACKING3) SPECIAL
PMM0204 0 = neutral G = ± 5 ppm/K
F = ± 10 ppm/K
E = ± 15 ppm/K
D = ± 25 ppm/K
C = ± 50 ppm/K
3 digit value
1 digit multiplier
0000 = Jumper
Multiplier
0 = *100
1 = *101
2 = *102
3 = *103
B = ± 0.1 %
C = ± 0.25 %
B1
B3
B0
M3
up to 2 digits
00 = standard
PRODUCT DESCRIPTION: PMM0204 15 562R 0.25% B0
PMM0204 15 562R 0.25 % B0
MODEL TC RESISTANCE
VALUE TOLERANCE PACKING3)
PMM0204 ± 5 ppm/K
± 10 ppm/K
± 15 ppm/K
± 25 ppm/K
± 50 ppm/K
100R = 100 Ω
221K = 221K Ω
± 0.1 %
± 0.25 %
B1
B3
B0
M3
02MMP040E5620CB000
www.vishay.com For Technical questions contact: ff3bresistors@vishay.com Document Number: 20006
44 Revision: 15-Feb-06
PMM0204
Vishay Draloric Metal Film Cylindrical Resistors
* For TC ≤ 25 ppm/K and Tolerance ≤ 0.25 % only.
Further information about PACKING, see also datasheet “surface mount resistor packing” (document number: 20014)
PACKING
MODEL BLISTER TAPE ON REEL
ACC. IEC 60286-3
BULK CASE
ACC. IEC 60286-6
DIAMETER PIECES/REEL CODE PIECES/ BULK CASE CODE
PMM0204
180 mm/7" 1000 B1*
3000 M3180 mm/7" 3000 B3
330 mm/13" 10000 B0
- 55 - 25 0 25 50 75 100
0
20
40
60
80
100
120
Derating Ambient Temperature in °C
Rated Power in %
70
1K 5K 10K 50K 100K 500K 1M
0.01
0.03
0.05
0.1
0.3
0.5
1
2
3
Current Noise
Resistance Value in Ω
Current Noise in µV/V
PERFORMANCE
TEST CONDITIONS OF TEST TEST RESULTS
Endurance Test at 70 °C
IEC 60115-1, 4.25.1 1000 hours at 70 °C, 1.5 hours "ON", 0.5 hours "OFF" ≤ 0.1 %
Endurance at UCT
IEC 60115-1, 4.25.3 1000 hours at 125 °C without load ≤ 0.1 %
Overload Test
IEC 60115-1, 4.13
Short time overload for 2 seconds
2.5 x rated voltage or ≤ 2 x limiting element voltage ≤ 0.02 %
Thermal Shock
IEC 60115-1, 4.19 and IEC 60068-2-14
Rapid change between upper and lower category
temperature, 5 cycles ≤ 0.02 %
Damp Heat Steady State
IEC 60115-1, 4.24 and IEC 60068-2-78 56 days at 40 °C and 93 % relative humidity ≤ 0.2 %
Resistance to Soldering Heat
IEC 60115-1, 4.18 and IEC 60068-2-58 10 seconds at 260 °C solder bath temperature ≤ 0.05 %
Document Number: 20006 For Technical questions contact: ff3bresistors@vishay.com www.vishay.com
Revision: 15-Feb-06 45
PMM0204
Metal Film Cylindrical Resistors Vishay Draloric
APPLICABLE SPECIFICATIONS
• EN 140401-803
• EN 140400
• EN 60115-1
Document Number: 91000 www.vishay.com
Revision: 18-Jul-08 1
Disclaimer
Legal Disclaimer Notice
Vishay
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
