Switching Power Supply Type SPD 5W DIN rail mounting * Universal AC input full range * Installation on DIN rail 7.5 or 15mm * Short circuit protection * Overload protection * High efficiency * LED indicator for DC power ON * LED indication for DC low * Internal input filter * CE, TUV approved and cULus Listed Product Description Ordering Key The Switching power supplies SPD series are specially designed to be used in all automation application where the Model Mounting ( D = Din rail ) Output voltage Output power Input Type Optional features installation is on a DIN rail and compact dimensions and performance are a must. Approvals SP D 12 05 1 B Input type: 1= single phase Optional Features Description code Spring connectors B Output performances Model Output Current (A) SPD05 SPD12 SPD15 SPD24 1.0 0.42 0.34 0.21 Voltage Trim Range Min. (VDC) Max. (VDC) 4.5 10.8 13.5 21.6 5.75 13.8 17.25 28.8 DC on LED (VDC Min.) DC low LED (VDC Min.) Typical Efficiency 4.5 10.8 13.5 21.6 3.75 9 11.25 18 69% 72% 72% 72% Output data Line regulation Load regulation Minimum load Transient recovery time Ripple and noise 1% 2% 0% 300 s 50mVpp Ouput Voltage accuracy Temperature coefficient Hold up Time Vi = 115Vac Hold up time Vi = 230Vac 100 - 240 Frequency range Inrush current Vi= 115Vac Vi= 230Vac 1% 0.02%/C 30ms 130ms Input data Rated input voltage Voltage range AC DC 90 - 265 Vac 120 - 370 Vdc Specifications are subject to change without notice 47- 63 Hz 10A 18A 1 Switching Power Supply Type SPD 5W DIN rail mounting Controls and Protections Overload Output Short Circuit Input Fuse 110 - 135% Hiccup mode T2A/250Vac internal* Dc out On, indicator Overvoltage Protection Dc out low, indicator >10.8Vdc 125 - 145% 9 - 10.8Vdc General data (@ nominal line, full load, 25C ) Ambient temperature Cooling Switching frequency Derating (>60C to +71C) Protection degree -10C to 71C Free air convection 100kHz 2.5%/C IP20 MTBF (MIL-HDBK-217F) Ambient humidity Case material Storage Dimensions L x W x D Weight 830.000h 20 - 95%RH Plastic: PC, UL94-V0 -25C to +85C 90 x 22.5 x 115 115g Approvals and EMC Insulation voltage I / O Insulation resistance UL / cUL 3.000Vac 100Mohm UL508, UL60950-1 listed, UL1310 Class 2 Recognised EN60950 TUV CE EN50081-1 / EN55022 Class B EN50082-1 / EN55024 EN61000-3-2 EN61000-3-3 * fuse not replaceable by user Block diagrams L Fuse Vo + Line Filter Inrush Current Limiter and Rectifier Switching Device Rectifier N Y Current Detection Vo - Control Opto isolation Reference & Error Amp. Opto isolation Over Voltage Detection Output Level Detection Vout ADJ. DCON (Green LED) DCLOW (Red LED) Pin assignement and front controls Pin No. 1 2 3 4 5 2 Designation V+ VGND N L Vout ADJ. ON LO Description Positive output terminal Negative output terminal Ground terminal to minimise High frequency emissions Neutral input ( no polarity with DC input ) Phase input ( no polarity with DC input ) Trimmer for fine output voltage adjustment DC output ready LED DC low indicator LED Specifications are subject to change without notice Switching Power Supply Type SPD 5W DIN rail mounting Derating Diagram Power out (%) 100 90 80 70 60 50 40 30 20 10 0 -10 0 5 10 Temperature (C) 55 60 65 70 75 80 Mechanical Drawings 22.5 (0.89) 2 115 (4.53) 1 90.0 (3.60) V- V+ 3 4 5 Installation Ventilation and cooling Connector size range Normal convection All sides 25mm free space for cooling is recommended Solid: 0.2 - 2mm2 (AWG24-14) (use copper conductors only) Specifications are subject to change without notice 3