October 2013
3-terminal Filters, SMD Array
For differential signal line (cellular band compatible)
MEA-LD series
MEA1210LD 1210[0504 inch]*
MEA1608LD 1608[0603 inch]
MEA2010LD 2010[0804 inch]
* Dimensions Code JIS[EIA]
EMC Components
(2/11)
001-01 / 20131004 / e9621_mea_differential.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
3-terminal Filters, SMD Array
For differential signal line (cellular band compatible)
FEATURES
LC filter with differential lines (D+ and D–) for high-density mounting.
Compact with a low profile design.
Can reduce radiation noise generated from differential signal lines (LVDS, MIPI, MDDI).
Effective as a desensitization countermeasure in information transmission terminals such as smart phones.
APPLICATION
Noise removal for differential transmission lines (MIPI, etc.) of various mobile devices.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Overview of the MEA-LD Series
MEA 1210 LD 120 T □□□
Series name L×W×T Dimensions Product internal
code
Capacitance Packaging style Internal code
(mm) (pF)
1210 1.2×1.0×0.5 LD 120 12 T Taping
1608 1.6×0.8×0.5 170 17
2010 2.0×1.0×0.5
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
（°C） （°C） （pieces/reel） （mg）
MEA1210LD –40 to +85 –40 to +85 4,000 3
MEA1608LD –40 to +85 –40 to +85 4,000 3.5
MEA2010LD –40 to +85 –40 to +85 4,000 5
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
Overview of the MEA-LD Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series
MEA1210LD Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
Dimensions in mm
0.65±0.05
1.0±0.15
0.5±0.1
GND
0.35±0.1 0.15min.
0.1min.
1.2±0.15
0.25±0.10.1min.
GND
CH2CH1
Dimensions in mm
0.3
0.65
0.6
0.25
0.9
1.8
0.5
CH2CH1
GNDGND
(6/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series MEA1210LD Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
22 250(Sdd) 6.3 100 MEA1210LD220T□□□
17 310(Sdd) 6.3 100 MEA1210LD170T□□□
12 410(Sdd) 6.3 100 MEA1210LD120T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
0
10
20
30
40
50
70
60
10 100 1000 10000
Insertion loss (dB)
Frequency (MHz)
220 Scc 120 Scc
220 Sdd
170 Sdd
120 Sdd
170 Scc
(7/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series
MEA1608LD Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
1.6±0.1
0.8±0.1
0.05min.
0.5±0.1
0.2±0.1
GND GND
0.2±0.1 0.15min.
0.4±0.050.4±0.05 0.4±0.05
CH4CH1 CH2 CH3
Dimensions in mm
0.2 to 0.25
2.0
0.025
0.15
0.5
0.15 to 0.2
0.4 0.04
0.35
0.35
Dimensions in mm
CH2
GND GND
CH1 CH4CH3
(8/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series MEA1608LD Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
22 270(Sdd) 6.3 50 MEA1608LD220T□□□
15 380(Sdd) 6.3 50 MEA1608LD150T□□□
10 500(Sdd) 6.3 50 MEA1608LD100T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
0
10
20
30
40
50
60
10 100 1000 10000
Insertion loss (dB)
Frequency (MHz)
220 Scc
150 Scc
100 Scc 220 Sdd
100 Sdd
150 Sdd
(9/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series
MEA2010LD Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM
2.0±0.15
1.0±0.15
0.10min.
0.5±0.1
0.25±0.1
GND GND
0.25±0.1 0.15min.
0.5±0.10.5±0.1 0.5±0.1
CH4CH1 CH2 CH3
Dimensions in mm
1.60
2.80
0.25
0.60
1.80
0.25
0.50
Dimensions in mm
(10/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series MEA2010LD Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
○Measurement equipment
＊ Equivalent measurement equipment may be used.
INSERTION LOSS VS. FREQUENCY CHARACTERISTICS
○Measurement equipment
＊ Equivalent measurement equipment may be used.
Capacitance
(pF)
Cutoff frequency
(MHz)typ.
Rated voltage
(V)max.
Rated current
(mA)max. Part No.
22 240(Sdd) 6.3 100 MEA2010LD220T□□□
17 330(Sdd) 6.3 100 MEA2010LD170T□□□
12 430(Sdd) 6.3 100 MEA2010LD120T□□□
Measurement item Product No. Manufacturer
Capacitance 4294A Agilent Technologies
Frequency characteristics N5230C Agilent Technologies
Product No. Manufacturer
N5230C Agilent Technologies
0
10
20
30
40
60
50
10 100 1000 10000
Insertion loss (dB)
Frequency (MHz)
220 Scc
170 Scc
120 Scc
220 Sdd
100 Sdd
150 Sdd
(11/11)
001-01 / 20131004 / e9621_mea_differential.fm
• All specifications are subject to change without notice.
EMC Components
MEA-LD series
Packaging style
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Type A B K t
MEA1210LD
1.20±0.05 1.45±0.05 0.73max.
—
MEA1608LD
1.00±0.10 1.80±0.10 1.0max. 0.25±0.05
MEA2010LD
1.15±0.05 2.15±0.05 1.0max.
—
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
B
A
8.0±0.3
3.5±0.05
1.75±0.1
4.0±0.1
4.0±0.1
2.0±0.05
1.5 +0.1
0
K
MEA1608LDMEA1210LD,
MEA2010LD
t
K
160min. Taping 200min.
300min.
Drawing direction
MEA2010LD
MEA1608LD
MEA1210LD
Dimensions in mm