42
01-02
Technical Data
Dielectric: Polypropylene film.
Capacitor electrodes: Metal foil.
Encapsulation: Flame-retardent plastic case, UL 94 V–0,
with epoxy resin seal. Colour: Green. Marking: Black.
Temperature range: –55) C to +100) C.
Test specifications: In accord. with IEC 60384-13 and EN 131 800.
Test category: 55/100/56 in accordance with IEC.
Insulation resistance at +20) C:
6 5 x 105 MV (mean value: 1 x 106 MV)
In accordance with IEC 60384-13 and EN 131 800.
Measuring voltage:
Ur = 63 V: Utest = 50 V/1 min.
Ur 6 100 V: Utest = 100 V/1 min.
Capacitance tolerances: ± 10 %, ± 5 %, ± 2.5 %,
(± 1 % available subject to special enquiry).
Temperature coefficient: –200 x 10-6 per degree C (typical).
Maximum pulse rise time: 1000 V/msec for
pulses equal to the rated voltage.
Dissipation factors at +20) C: tan d
Test voltage: 2 Ur, 2 sec.
Vibration: 6 hours at 10 . . . 2000 Hz and 0.75 mm displacement
amplitude or 10 g in accordance with IEC 60068-2-6.
Low air density: 1 kPa = 10 mbar in accordance with
IEC 60068-2-13.
Bump test: 4000 bumps at 390 m/sec2 in accordance with
IEC 60068-2-29.
Dielectric absorption: 0.05 %.
Voltage derating: A voltage derating factor of 1.35 % per K
must be applied from +85) C for DC voltages and from
+75) C for AC voltages.
Graphs see page 7.
1000 pF 4700 pF
at f C 5 1000 pF ‹ C 5 4700 pF ‹ C 5 0.033 mF
1 kHz 5 3 x 10-4 5 4 x 10-4 5 4 x 10-4
10 kHz 5 3 x 10-4 5 4 x 10-4 5 4 x 10-4
100 kHz 5 4 x 10-4 5 5 x 10-4 –
1 MHz 5 10 x 10-4 – –
WIMA FKP 2
Impulsfeste Polypropylen-Film/Folien-
Kondensatoren im Rastermaß 5 mm
˜ Für Impulsapplikationen mit hoher Eigenresonanz-
f re q ue n z. ˜ Zur Substitution von Styroflex-Konden-
satoren im Audio- und HF-Bereich. ˜ Nennspan-
nungen bis 1000 V–. ˜ Eingeengte Toleranzen bis
1 %.
Polypropylene film and foil capacitors
for pulse applications in PCM 5 mm
˜ For all pulse applications with high repetition fre-
quency. ˜ For substitution of polystyrene capac-
itors in audio and HF-applications. ˜ Voltage
ranges up to 1000 VDC. ˜ Close tolerances up
to 1 %.
Technische Angaben
Dielektrikum: Polypropylen-Folie.
Beläge: Metallfolie.
Umhüllung: Flammhemmendes Kunststoffgehäuse, UL 94 V–0,
Epoxidharzverguß. Farbe: Grün. Aufdruck: Schwarz.
Temperaturbereich: –55) C bis +100) C.
Prüfungen: Nach IEC 60384-13 bzw. EN 131 800.
Prüfklasse: 55/100/56 nach IEC.
Isolationswerte bei +20) C:
6 5 „ 105 MV (Mittelwert: 1 „ 106 MV)
Nach IEC 60384-13 und EN 131 800.
Meßspannung:
UN = 63 V: Umeß = 50 V/1 min.
UN 6 100 V: Umeß = 100 V/1 min.
Kapazitätstoleranzen: ± 10 %, ± 5 %, ± 2.5 %,
(± 1 % auf Anfrage).
Temperaturbeiwert: –200 „ 10-6/) C (typisch).
Impulsbelastung: Flankensteilheit 1000 V/ms
bei vollem Spannungshub.
Verlustfaktoren bei +20) C: tan d
Prüfspannung: 2 UN, 2 s.
Schwingen: 6 h bei 10 . . . 2000 Hz und 0,75 mm Auslenkung bzw.
10 g nach IEC 60068-2-6.
Unterdruck: 1 kPa = 10 mbar nach IEC 60068-2-13.
Stoßtest: 4000 Stöße mit 390 m/s2 nach IEC 60068-2-29.
Dielektrische Absorption: 0,05 %.
Spannungsderating: Die zulässige Spannung vermindert sich
gegenüber der Nennspannung bei Gleichspannungsbetrieb ab
+85) C, bei Wechselspannungsbetrieb ab +75) C um 1,35 %
je 1 K.
Kurven siehe Seite 7.
Gemessen 1000 pF 4700 pF
bei C 5 1000 pF ‹ C 5 4700 pF ‹ C 5 0,033 mF
1 kHz 5 3 „ 10-4 5 4 „ 10-4 5 4 „ 10-4
10 kHz 5 3 „ 10-4 5 4 „ 10-4 5 4 „ 10-4
100 kHz 5 4 „ 10-4 5 5 „ 10-4 –
1 MHz 5 10 „ 10-4 – –