Si864x Data Sheet
Low-Power Quad-Channel Digital Isolators
Silicon Lab's family of ultra-low-power digital isolators are CMOS devices offering sub-
stantial data rate, propagation delay, power, size, reliability, and external BOM advan-
tages over legacy isolation technologies. The operating parameters of these products
remain stable across wide temperature ranges and throughout device service life for
ease of design and highly uniform performance. All device versions have Schmitt trigger
inputs for high noise immunity and only require VDD bypass capacitors.
Data rates up to 150 Mbps are supported, and all devices achieve propagation delays of
less than 10 ns. Enable inputs provide a single point control for enabling and disabling
output drive. Ordering options include a choice of isolation ratings (1.0, 2.5, 3.75 and 5
kV) and a selectable fail-safe operating mode to control the default output state during
power loss. All products >1 kV are safety certified by UL, CSA, VDE, and CQC, and
products in wide-body packages support reinforced insulation withstanding up to 5
kVRMS.
Automotive Grade is available for certain part numbers. These products are built using
automotive-specific flows at all steps in the manufacturing process to ensure the robust-
ness and low defectivity required for automotive applications.
KEY FEATURES
• High-speed operation
•DC to 150 Mbps
• No start-up initialization required
• Wide Operating Supply Voltage
• 2.5–5.5 V
• Up to 5000 VRMS isolation
• Reinforced VDE 0884-10, 10 kV surge-
capable (Si864xxT)
• 60-year life at rated working voltage
• High electromagnetic immunity
• Ultra low power (typical)
5 V Operation
• 1.6 mA per channel at 1 Mbps
• 5.5 mA per channel at 100 Mbps
2.5 V Operation
• 1.5 mA per channel at 1 Mbps
• 3.5 mA per channel at 100 Mbps
• Tri-state outputs with ENABLE
• Schmitt trigger inputs
• Selectable fail-safe mode
• Default high or low output (ordering
option)
• Precise timing (typical)
• 10 ns propagation delay
• 1.5 ns pulse width distortion
• 0.5 ns channel-channel skew
• 2 ns propagation delay skew
• 5 ns minimum pulse width
• Transient Immunity 50 kV/µs
• AEC-Q100 qualification
• Wide temperature range
• –40 to 125 °C
• RoHS-compliant packages
• SOIC-16 wide body
• SOIC-16 narrow body
• QSOP-16
• Automotive-grade OPNs available
• AIAG compliant PPAP documentation
support
• IMDS and CAMDS listing support
Industrial Applications
•Industrial automation systems
• Medical electronics
• Isolated switch mode supplies
• Isolated ADC, DAC
• Motor control
• Power inverters
• Communications systems
Safety Regulatory Approvals
• UL 1577 recognized
• Up to 5000 VRMS for 1 minute
• CSA component notice 5A approval
• IEC 60950-1, 62368-1, 60601-1 (re-
inforced insulation)
• VDE certification conformity
• Si864xxT options certified to rein-
forced VDE 0884-10
• All other options certified to basic
VDE 0884-10 and reinforced 60950-1
• CQC certification approval
• GB4943.1
Automotive Applications
•On-board chargers
• Battery management systems
• Charging stations
• Traction inverters
• Hybrid Electric Vehicles
• Battery Electric Vehicles
silabs.com | Building a more connected world. Rev. 2.13
1. Ordering Guide
Table 1.1. Ordering Guide for Valid OPNs1, 2
Ordering Part Number (OPN)
Number of
Inputs
VDD1
Side
Number of
Inputs
VDD2
Side
Max Data
Rate
(Mbps)
Default
Output
State
Isolation
Rating
(kV)
Temp (°C) Package
QSOP-16 Packages
Si8640BA-B-IU 4 0 150 Low 1.0 –40 to 125 °C QSOP-16
Si8640BB-B-IU 4 0 150 Low 2.5 –40 to 125 °C QSOP-16
Si8640EB-B-IU 4 0 150 High 2.5 –40 to 125 °C QSOP-16
Si8641BA-B-IU 3 1 150 Low 1.0 –40 to 125 °C QSOP-16
Si8641BA-C-IU 3 1 150 Low 1.0 –40 to 125 °C QSOP-16
Si8641BB-B-IU 3 1 150 Low 2.5 –40 to 125 °C QSOP-16
Si8641EB-B-IU 3 1 150 High 2.5 –40 to 125 °C QSOP-16
Si8642BA-B-IU 2 2 150 Low 1.0 –40 to 125 °C QSOP-16
Si8642BA-C-IU 2 2 150 Low 1.0 –40 to 125 °C QSOP-16
Si8642BB-B-IU 2 2 150 Low 2.5 –40 to 125 °C QSOP-16
Si8642EA-B-IU 2 2 150 High 1.0 –40 to 125 °C QSOP-16
Si8642EB-B-IU 2 2 150 High 2.5 –40 to 125 °C QSOP-16
Si8645BA-B-IU 4 0 150 Low 1.0 –40 to 125 °C QSOP-16
Si8645BA-C-IU 4 0 150 Low 1.0 –40 to 125 °C QSOP-16
Si8645BB-B-IU 4 0 150 Low 2.5 –40 to 125 °C QSOP-16
SOIC-16 Packages
Si8640BB-B-IS1 4 0 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8640BB-B-IS 4 0 150 Low 2.5 –40 to 125 °C WB SOIC-16
Si8640BC-B-IS1 4 0 150 Low 3.75 –40 to 125 °C NB SOIC-16
Si8640BD-B-IS2 4 0 150 Low 5.0 –40 to 125 ˚C WB SOIC-16
(8 mm creepage)4
Si8640BD-B-IS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8640EC-B-IS1 4 0 150 High 3.75 –40 to 125 °C NB SOIC-16
Si8640ED-B-IS2 4 0 150 High 5.0 –40 to 125 ˚C WB SOIC-16
(8 mm creepage)4
Si8640ED-B-IS 4 0 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8641BB-B-IS1 3 1 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8641BB-B-IS 3 1 150 Low 2.5 –40 to 125 °C WB SOIC-16
Si8641BC-B-IS1 3 1 150 Low 3.75 –40 to 125 °C NB SOIC-16
Si8641BD-B-IS2 3 1 150 Low 5.0 –40 to 125 °C WB SOIC-16
(8 mm creepage)4
Si864x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 2.13 | 2
Ordering Part Number (OPN)
Number of
Inputs
VDD1
Side
Number of
Inputs
VDD2
Side
Max Data
Rate
(Mbps)
Default
Output
State
Isolation
Rating
(kV)
Temp (°C) Package
Si8641BD-B-IS 3 1 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8641EC-B-IS1 3 1 150 High 3.75 –40 to 125 °C NB SOIC-16
Si8641ED-B-IS2 3 1 150 High 5.0 –40 to 125 °C WB SOIC-16
(8 mm creepage)4
Si8641ED-B-IS 3 1 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8642BB-B-IS1 2 2 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8642BB-B-IS 2 2 150 Low 2.5 –40 to 125 °C WB SOIC-16
Si8642BC-B-IS1 2 2 150 Low 3.75 –40 to 125 °C NB SOIC-16
Si8642BD-B-IS2 2 2 150 Low 5.0 –40 to 125 °C WB SOIC-16
(8 mm creepage)4
Si8642BD-B-IS 2 2 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8642EC-B-IS1 2 2 150 High 3.75 –40 to 125 °C NB SOIC-16
Si8642ED-B-IS2 2 2 150 High 5.0 –40 to 125 °C WB SOIC-16
(8 mm creepage)4
Si8642ED-B-IS 2 2 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8645BB-B-IS1 4 0 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8645BB-B-IS 4 0 150 Low 2.5 –40 to 125 °C WB SOIC-16
Si8645BC-B-IS1 4 0 150 Low 3.75 –40 to 125 °C NB SOIC-16
Si8645BD-B-IS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Product Options with Reinforced VDE 0884-10 Rating with 10 kV Surge Capability
Si8640BT-IS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8640ET-IS 4 0 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8641BT-IS 3 1 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8641ET-IS 3 1 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8642BT-IS 2 2 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8642ET-IS 2 2 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8645BT-IS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8645ET-IS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Note:
1. All packages are RoHS-compliant with peak reflow temperatures of 260 °C according to the JEDEC industry standard classifica-
tions and peak solder temperatures.
2. “Si” and “SI” are used interchangeably.
3. An "R" at the end of the part number denotes tape and reel packaging option.
4. The package designated IS2 has a design that eliminates tie bars, thus allowing for extra creepage distance while maintaining
standard WB SOIC-16 package dimensions and land pattern.
Si864x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 2.13 | 3
Automotive Grade OPNs
Automotive-grade devices are built using automotive-specific flows at all steps in the manufacturing process to ensure robustness and
low defectivity. These devices are supported with AIAG-compliant Production Part Approval Process (PPAP) documentation, and fea-
ture International Material Data System (IMDS) and China Automotive Material Data System (CAMDS) listing. Qualifications are compli-
ant with AEC-Q100, and a zero-defect methodology is maintained throughout definition, design, evaluation, qualification, and mass pro-
duction steps.
Table 1.2. Ordering Guide for Automotive Grade OPNs1, 2, 4, 5
Ordering Part Number
(OPN)
Number of
Inputs
VDD1
Side
Number of
Inputs
VDD2
Side
Max Data
Rate
(Mbps)
Default
Output
State
Isolation
Rating
(kV)
Temp (°C) Package
QSOP-16 Packages
Si8642EA-AU 2 2 150 High 1.0 –40 to 125 °C QSOP-16
SOIC-16 Packages
Si8640BB-AS 4 0 150 Low 2.5 –40 to 125 °C WB SOIC-16
Si8640BD-AS 4 0 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8640ED-AS 4 0 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8641BB-AS1 3 1 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8641BC-AS1 3 1 150 Low 3.75 –40 to 125 °C NB SOIC-16
Si8641BD-AS 3 1 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8641ED-AS 3 1 150 High 5.0 –40 to 125 °C WB SOIC-16
Si8642BB-AS1 2 2 150 Low 2.5 –40 to 125 °C NB SOIC-16
Si8642BD-AS 2 2 150 Low 5.0 –40 to 125 °C WB SOIC-16
Si8642EC-AS1 2 2 150 High 3.75 –40 to 125 °C NB SOIC-16
Si8642ED-AS 2 2 150 High 5.0 –40 to 125 °C WB SOIC-16
Product Options with Reinforced VDE 0884-10 Rating with 10 kV Surge Capability
Si8642ET-AS 2 2 150 High 5.0 –40 to 125 °C WB SOIC-16
Note:
1. All packages are RoHS-compliant with peak reflow temperatures of 260 °C according to the JEDEC industry standard classifica-
tions.
2. “Si” and “SI” are used interchangeably.
3. An "R" at the end of the part number denotes tape and reel packaging option.
4. Automotive-Grade devices (with an "–A" suffix) are identical in construction materials, topside marking, and electrical parameters
to their Industrial-Grade (with a "–I" suffix) version counterparts. Automotive-Grade products are produced utilizing full automotive
process flows and additional statistical process controls throughout the manufacturing flow. The Automotive-Grade part number is
included on shipping labels.
5. Additional Ordering Part Numbers may be available in Automotive-Grade. Please contact your local Silicon Labs sales represen-
tative for further information.
Si864x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 2.13 | 4
Table of Contents
1. Ordering Guide ..............................2
2. Functional Description............................6
2.1 Theory of Operation ............................6
2.2 Eye Diagram...............................7
3. Device Operation ..............................8
3.1 Device Startup ..............................10
3.2 Undervoltage Lockout ...........................10
3.3 Layout Recommendations ..........................10
3.3.1 Supply Bypass ............................10
3.3.2 Output Pin Termination..........................10
3.4 Fail-Safe Operating Mode ..........................10
3.5 Typical Performance Characteristics.......................11
4. Electrical Specifications ..........................12
5. Pin Descriptions .............................28
6. Package Outline (16-Pin Wide Body SOIC) ...................29
7. Land Pattern (16-Pin Wide Body SOIC) ..................... 31
8. Package Outline (16-Pin Narrow Body SOIC) ..................32
9. Land Pattern (16-Pin Narrow Body SOIC) ....................34
10. Package Outline (16-Pin QSOP) .......................35
11. Land Pattern (16-Pin QSOP) ........................37
12. Top Marking (16-Pin Wide Body SOIC) ....................38
13. Top Marking (16-Pin Narrow Body SOIC) ...................39
14. Top Marking (16-Pin QSOP) ........................40
15. Revision History............................. 41
silabs.com | Building a more connected world. Rev. 2.13 | 5
2. Functional Description
2.1 Theory of Operation
The operation of an Si864x channel is analogous to that of an opto coupler, except an RF carrier is modulated instead of light. This
simple architecture provides a robust isolated data path and requires no special considerations or initialization at start-up. A simplified
block diagram for a single Si864x channel is shown in the figure below.
Figure 2.1. Simplified Channel Diagram
A channel consists of an RF Transmitter and RF Receiver separated by a semiconductor-based isolation barrier. Referring to the trans-
mitter, input A modulates the carrier provided by an RF oscillator using on/off keying. The Receiver contains a demodulator that de-
codes the input state according to its RF energy content and applies the result to output B via the output driver. This RF on/off keying
scheme is superior to pulse code schemes as it provides best-in-class noise immunity, low power consumption, and improved immunity
to magnetic fields. See the following figure for more details.
Figure 2.2. Modulation Scheme
Si864x Data Sheet
Functional Description
silabs.com | Building a more connected world. Rev. 2.13 | 6
2.2 Eye Diagram
The figure below illustrates an eye diagram taken on an Si8640. For the data source, the test used an Anritsu (MP1763C) Pulse Pattern
Generator set to 1000 ns/div. The output of the generator's clock and data from an Si8640 were captured on an oscilloscope. The re-
sults illustrate that data integrity was maintained even at the high data rate of 150 Mbps. The results also show that 2 ns pulse width
distortion and 350 ps peak jitter were exhibited.
Figure 2.3. Eye Diagram
Si864x Data Sheet
Functional Description
silabs.com | Building a more connected world. Rev. 2.13 | 7
3. Device Operation
Device behavior during start-up, normal operation, and shutdown is shown in Figure 3.1 Device Behavior during Normal Operation on
page 10, where UVLO+ and UVLO– are the respective positive-going and negative-going thresholds. Refer to the following tables to
determine outputs when power supply (VDD) is not present and for logic conditions when enable pins are used.
Table 3.1. Si86xx Logic Operation
VI Input1, 2 EN Input1, 2, 3, 4 VDDI State1, 5, 6 VDDO State1, 5, 6 VO Output1, 2 Comments
H H or NC P P H Enabled, normal operation.
L H or NC P P L
X7L P P Hi-Z8Disabled.
X7H or NC UP P L9
H9
Upon transition of VDDI from unpowered to
powered, VO returns to the same state as VI
in less than 1 µs.
X7L UP P Hi-Z8Disabled.
X7X7P UP Undetermined Upon transition of VDDO from unpowered to
powered, VO returns to the same state as VI
within 1 µs, if EN is in either the H or NC
state. Upon transition of VDDO from unpow-
ered to powered, VO returns to Hi-Z within 1
µs if EN is L.
Note:
1. VDDI and VDDO are the input and output power supplies. VI and VO are the respective input and output terminals. EN is the
enable control input located on the same output side.
2. X = not applicable; H = Logic High; L = Logic Low; Hi-Z = High Impedance.
3. It is recommended that the enable inputs be connected to an external logic high or low level when the Si86xx is operating in noisy
environments.
4. No Connect (NC) replaces EN1 on Si8640/45. No Connect replaces EN2 on the Si8645. No Connects are not internally connec-
ted and can be left floating, tied to VDD, or tied to GND.
5. “Powered” state (P) is defined as 2.5 V < VDD < 5.5 V.
6. “Unpowered” state (UP) is defined as VDD = 0 V.
7. Note that an I/O can power the die for a given side through an internal diode if its source has adequate current.
8. When using the enable pin (EN) function, the output pin state is driven into a high-impedance state when the EN pin is disabled
(EN = 0).
9. See 1. Ordering Guide for details. This is the selectable fail-safe operating mode (ordering option). Some devices have default
output state = H, and some have default output state = L, depending on the ordering part number (OPN). For default high devi-
ces, the data channels have pull-ups on inputs/outputs. For default low devices, the data channels have pull-downs on inputs/
outputs.
Si864x Data Sheet
Device Operation
silabs.com | Building a more connected world. Rev. 2.13 | 8
Table 3.2. Enable Input Truth
Part Number EN11, 2 EN21, 2 Operation
Si8640 — H Outputs B1, B2, B3, B4 are enabled and follow the input state.
— L Outputs B1, B2, B3, B4 are disabled and in high impedance state.3
Si8641 H X Output A4 enabled and follows the input state.
L X Output A4 disabled and in high impedance state.3
X H Outputs B1, B2, B3 are enabled and follow the input state.
X L Outputs B1, B2, B3 are disabled and in high impedance state.3
Si8642 H X Outputs A3 and A4 are enabled and follow the input state.
L X Outputs A3 and A4 are disabled and in high impedance state.3
X H Outputs B1 and B2 are enabled and follow the input state.
X L Outputs B1 and B2 are disabled and in high impedance state.3
Si8645 — — Outputs B1, B2, B3, B4 are enabled and follow the input state.
Note:
1. Enable inputs EN1 and EN2 can be used for multiplexing, for clock sync, or other output control. EN1, EN2 logic operation is
summarized for each isolator product in Table 2. These inputs are internally pulled-up to local VDD allowing them to be connec-
ted to an external logic level (high or low) or left floating. To minimize noise coupling, do not connect circuit traces to EN1 or EN2
if they are left floating. If EN1, EN2 are unused, it is recommended they be connected to an external logic level, especially if the
Si86xx is operating in a noisy environment.
2. X = not applicable; H = Logic High; L = Logic Low.
3. When using the enable pin (EN) function, the output pin state is driven into a high-impedance state when the EN pin is disabled
(EN = 0).
Si864x Data Sheet
Device Operation
silabs.com | Building a more connected world. Rev. 2.13 | 9
3.1 Device Startup
Outputs are held low during powerup until VDD is above the UVLO threshold for time period tSTART. Following this, the outputs follow
the states of inputs.
3.2 Undervoltage Lockout
Undervoltage Lockout (UVLO) is provided to prevent erroneous operation during device startup and shutdown or when VDD is below its
specified operating circuits range. Both Side A and Side B each have their own undervoltage lockout monitors. Each side can enter or
exit UVLO independently. For example, Side A unconditionally enters UVLO when VDD1 falls below VDD1(UVLO–) and exits UVLO when
VDD1 rises above VDD1(UVLO+). Side B operates the same as Side A with respect to its VDD2 supply.
Figure 3.1. Device Behavior during Normal Operation
3.3 Layout Recommendations
To ensure safety in the end-user application, high-voltage circuits (i.e., circuits with >30 VAC) must be physically separated from the
safety extra-low-voltage circuits (SELV is a circuit with <30 VAC) by a certain distance (creepage/clearance). If a component, such as a
digital isolator, straddles this isolation barrier, it must meet those creepage/clearance requirements and also provide a sufficiently large
high-voltage breakdown protection rating (commonly referred to as working voltage protection). Table 4.6 Insulation and Safety-Related
Specifications on page 24 and Table 4.8 VDE 0884-10 Insulation Characteristics for Si86xxxx 1 on page 25 detail the working volt-
age and creepage/clearance capabilities of the Si86xx. These tables also detail the component standards (UL1577, IEC60747, CSA
5A), which are readily accepted by certification bodies to provide proof for end-system specifications requirements. Refer to the end-
system specification (61010-1, 60950-1, 60601-1, etc.) requirements before starting any design that uses a digital isolator.
3.3.1 Supply Bypass
The Si864x family requires a 0.1 µF bypass capacitor between VDD1 and GND1 and VDD2 and GND2. The capacitor should be placed
as close as possible to the package. To enhance the robustness of a design, the user may also include resistors (50–300 Ω ) in series
with the inputs and outputs if the system is excessively noisy.
3.3.2 Output Pin Termination
The nominal output impedance of an isolator driver channel is approximately 50 Ω, ±40%, which is a combination of the value of the on-
chip series termination resistor and channel resistance of the output driver FET. When driving loads where transmission line effects will
be a factor, output pins should be appropriately terminated with controlled impedance PCB traces.
3.4 Fail-Safe Operating Mode
Si86xx devices feature a selectable (by ordering option) mode whereby the default output state (when the input supply is unpowered)
can either be a logic high or logic low when the output supply is powered. See Table 3.1 Si86xx Logic Operation on page 8 and
1. Ordering Guide for more information.
Si864x Data Sheet
Device Operation
silabs.com | Building a more connected world. Rev. 2.13 | 10
3.5 Typical Performance Characteristics
The typical performance characteristics depicted in the following diagrams are for information purposes only. Refer to 4. Electrical
Specifications for actual specification limits.
Figure 3.2. Si8640/45 Typical VDD1 Supply Current vs. Data
Rate 5, 3.3, and 2.5 V Operation Figure 3.3. Si8640/45 Typical VDD2 Supply Current vs. Data
Rate 5, 3.3, and 2.5 V
Figure 3.4. Si8641 Typical VDD1 Supply Current vs. Data
Rate 5, 3.3, and 2.5 V Operation Figure 3.5. Si8641 Typical VDD2 Supply Current vs. Data Rate
5, 3.3, and 2.5 V Operation (15 pF Load)
Figure 3.6. Si8642 Typical VDD1 or VDD2 Supply Current vs.
Data Rate 5, 3.3, and 2.5 V Operation (15 pF Load)
Figure 3.7. Propagation Delay vs. Temperature (5.0 V Data)
Si864x Data Sheet
Device Operation
silabs.com | Building a more connected world. Rev. 2.13 | 11
4. Electrical Specifications
Table 4.1. Recommended Operating Conditions
Parameter Symbol Min Typ Max Unit
Junction Operating Temperature TJ— — 150 °C
Ambient Operating Temperature 1TA–40 25 125 °C
Supply Voltage
VDD1 2.375 — 5.5 V
VDD2 2.375 — 5.5 V
Note:
1. The maximum ambient temperature is dependent on data frequency, output loading, number of operating channels, and supply
voltage.
Table 4.2. Electrical Characteristics
(VDD1 = 5 V±10%, VDD2 = 5 V±10%, TA = –40 to 125 °C)
Parameter Symbol Test Condition Min Typ Max Unit
VDD Undervoltage Threshold VDDUV+ VDD1, VDD2 rising 1.95 2.24 2.375 V
VDD Undervoltage Threshold VDDUV– VDD1, VDD2 falling 1.88 2.16 2.325 V
VDD Undervoltage Hysteresis VDDHYS 50 70 95 mV
Positive-Going Input Threshold VT+ All inputs rising 1.4 1.67 1.9 V
Negative-Going Input Threshold VT– All inputs falling 1.0 1.23 1.4 V
Input Hysteresis VHYS 0.38 0.44 0.50 V
High Level Input Voltage VIH 2.0 — — V
Low Level Input Voltage VIL — — 0.8 V
High Level Output Voltage VOH loh = –4 mA VDD1, VDD2 – 0.4 4.8 — V
Low Level Output Voltage VOL lol = 4 mA — 0.2 0.4 V
Input Leakage Current
Si864xxA/B/C/D
Si864xxT
IL—
—
—
—
±10
±15
µA
Output Impedance 1ZO— 50 — Ω
Enable Input Current
Si864xxA/B/C/D
Si864xxT
IENH, IENL VENx = VIH or VIL —
—
2.0
10.0
—
—
µA
DC Supply Current (All Inputs 0 V or at Supply)
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 12
Parameter Symbol Test Condition Min Typ Max Unit
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.0
2.4
6.1
2.5
1.6
3.8
9.2
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.4
2.3
5.2
3.6
2.2
3.7
7.8
5.4
mA
Si8642Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.8
1.8
4.4
4.4
2.9
2.9
6.6
6.6
mA
1 Mbps Supply Current (All Inputs = 500 kHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
2.9
5.0
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.4
3.3
4.8
4.6
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.3
3.3
4.6
4.6
mA
10 Mbps Supply Current (All Inputs = 5 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
4.0
5.0
5.6
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.7
4.1
5.2
5.8
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.9
3.9
5.4
5.4
mA
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 13
Parameter Symbol Test Condition Min Typ Max Unit
100 Mbps Supply Current (All Inputs = 50 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
17.5
5.0
22.8
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
7.3
14.3
9.8
18.5
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
11
11
14.3
14.3
mA
Timing Characteristics
Si864xBx, Ex
Maximum Data Rate 0 — 150 Mbps
Minimum Pulse Width — — 5.0 ns
Propagation Delay tPHL, tPLH See Figure 4.2 Propagation
Delay Timing on page 16
5.0 8.0 13 ns
Pulse Width Distortion
|tPLH – tPHL|
PWD See Figure 4.2 Propagation
Delay Timing on page 16 — 0.2 4.5 ns
Propagation Delay Skew 2 tPSK(P-P) — 2.0 4.5 ns
Channel-Channel Skew tPSK — 0.4 2.5 ns
All Models
Output Rise Time tr
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Output Fall Time tf
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Peak Eye Diagram Jitter tJIT(PK) See Figure 2.3 Eye Diagram
on page 7
— 350 — ps
Common Mode Transient Immunity
Si86xxxA/B/C/D
Si86xxxT
CMTI
VI = VDD or 0 V
VCM = 1500 V
See Figure 4.3 Common-
Mode Transient Immunity Test
Circuit on page 16
35
60
50
100
—
—
kV/µs
Enable to Data Valid ten1 See Figure 4.1 ENABLE Tim-
ing Diagram on page 16
— 6.0 11 ns
Enable to Data Tri-State ten2 See Figure 4.1 ENABLE Tim-
ing Diagram on page 16
— 8.0 12 ns
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 14
Parameter Symbol Test Condition Min Typ Max Unit
Input power loss to valid default output tSD See Figure 3.1 Device Behav-
ior during Normal Operation
on page 10
— 8.0 12 ns
Start-up Time 3 tSU — 15 40 µs
Note:
1. The nominal output impedance of an isolator driver channel is approximately 50 Ω, ±40%, which is a combination of the value of
the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads where transmission
line effects will be a factor, output pins should be appropriately terminated with controlled-impedance PCB traces.
2. tPSK(P-P) is the magnitude of the difference in propagation delay times measured between different units operating at the same
supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to the appearance of valid data at the output.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 15
Figure 4.1. ENABLE Timing Diagram
Figure 4.2. Propagation Delay Timing
Figure 4.3. Common-Mode Transient Immunity Test Circuit
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 16
Table 4.3. Electrical Characteristics
(VDD1 = 3.3 V ±10%, VDD2 = 3.3 V ±10%, TA = –40 to 125 °C)
Parameter Symbol Test Condition Min Typ Max Unit
VDD Undervoltage Threshold VDDUV+ VDD1, VDD2 rising 1.95 2.24 2.375 V
VDD Undervoltage Threshold VDDUV– VDD1, VDD2 falling 1.88 2.16 2.325 V
VDD Undervoltage Hysteresis VDDHYS 50 70 95 mV
Positive-Going Input Threshold VT+ All inputs rising 1.4 1.67 1.9 V
Negative-Going Input Threshold VT– All inputs falling 1.0 1.23 1.4 V
Input Hysteresis VHYS 0.38 0.44 0.50 V
High Level Input Voltage VIH 2.0 — — V
Low Level Input Voltage VIL — — 0.8 V
High Level Output Voltage VOH loh = –4 mA VDD1, VDD2 – 0.4 3.1 — V
Low Level Output Voltage VOL lol = 4 mA — 0.2 0.4 V
Input Leakage Current
Si864xxA/B/C/D
Si864xxT
IL—
—
—
—
±10
±15
µA
Output Impedance 1ZO— 50 — Ω
Enable Input Current
Si864xxA/B/C/D
Si864xxT
IENH, IENL VENx = VIH or VIL —
—
2.0
10.0
—
—
µA
DC Supply Current (All Inputs 0 V or at Supply)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.0
2.4
6.1
2.5
1.6
3.8
9.2
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.4
2.3
5.2
3.6
2.2
3.7
7.8
5.4
mA
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 17
Parameter Symbol Test Condition Min Typ Max Unit
Si8642Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.8
1.8
4.4
4.4
2.9
2.9
6.6
6.6
mA
1 Mbps Supply Current (All Inputs = 500 kHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
2.9
5.0
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.4
3.3
4.8
4.6
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.3
3.3
4.6
4.6
mA
10 Mbps Supply Current (All Inputs = 5 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
3.4
5.0
4.7
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.5
3.6
4.9
5.1
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.6
3.6
5.0
5.0
mA
100 Mbps Supply Current (All Inputs = 50 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
12.3
5.0
15.9
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
5.9
10.3
7.9
13.4
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
8.2
8.2
10.7
10.7
mA
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 18
Parameter Symbol Test Condition Min Typ Max Unit
Timing Characteristics
Si864xBx, Ex
Maximum Data Rate 0 — 150 Mbps
Minimum Pulse Width — — 5.0 ns
Propagation Delay tPHL, tPLH See Figure 4.2 Propagation
Delay Timing on page 16
5.0 8.0 13 ns
Pulse Width Distortion
|tPLH – tPHL|
PWD See Figure 4.2 Propagation
Delay Timing on page 16 — 0.2 4.5 ns
Propagation Delay Skew 2 tPSK(P-P) — 2.0 4.5 ns
Channel-Channel Skew tPSK — 0.4 2.5 ns
All Models
Output Rise Time tr
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Output Fall Time tf
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Peak Eye Diagram Jitter tJIT(PK) See Figure 2.3 Eye Diagram
on page 7
— 350 — ps
Common Mode Transient Immunity
Si86xxxA/B/C/D
Si86xxxT
CMTI
VI = VDD or 0 V
VCM = 1500 V
See Figure 4.3 Common-
Mode Transient Immunity
Test Circuit on page 16
35
60
50
100
—
—
kV/µs
Enable to Data Valid ten1 See Figure 4.1 ENABLE
Timing Diagram on page 16
— 6.0 11 ns
Enable to Data Tri-State ten2 See Figure 4.1 ENABLE
Timing Diagram on page 16
— 8.0 12 ns
Input power loss to valid default output tSD See Figure 3.1 Device Be-
havior during Normal Opera-
tion on page 10
— 8.0 12 ns
Start-up Time 3 tSU — 15 40 µs
Note:
1. The nominal output impedance of an isolator driver channel is approximately 50 Ω, ±40%, which is a combination of the value of
the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads where transmission
line effects will be a factor, output pins should be appropriately terminated with controlled-impedance PCB traces.
2. tPSK(P-P) is the magnitude of the difference in propagation delay times measured between different units operating at the same
supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to the appearance of valid data at the output.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 19
Table 4.4. Electrical Characteristics
(VDD1 = 2.5 V ±5%, VDD2 = 2.5 V ±5%, TA = –40 to 125 °C)
Parameter Symbol Test Condition Min Typ Max Unit
VDD Undervoltage Threshold VDDUV+ VDD1, VDD2 rising 1.95 2.24 2.375 V
VDD Undervoltage Threshold VDDUV– VDD1, VDD2 falling 1.88 2.16 2.325 V
VDD Undervoltage Hysteresis VDDHYS 50 70 95 mV
Positive-Going Input Threshold VT+ All inputs rising 1.4 1.67 1.9 V
Negative-Going Input Threshold VT– All inputs falling 1.0 1.23 1.4 V
Input Hysteresis VHYS 0.38 0.44 0.50 V
High Level Input Voltage VIH 2.0 — — V
Low Level Input Voltage VIL — — 0.8 V
High Level Output Voltage VOH loh = –4 mA VDD1, VDD2 – 0.4 2.3 — V
Low Level Output Voltage VOL lol = 4 mA — 0.2 0.4 V
Input Leakage Current
Si864xxA/B/C/D
Si864xxT
IL—
—
—
—
±10
±15
µA
Output Impedance1ZO— 50 — Ω
Enable Input Current
Si864xxA/B/C/D
Si864xxT
IENH, IENL VENx = VIH or VIL —
—
2.0
10.0
—
—
µA
DC Supply Current (All Inputs 0 V or at Supply)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.0
2.4
6.1
2.5
1.6
3.8
9.2
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.4
2.3
5.2
3.6
2.2
3.7
7.8
5.4
mA
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 20
Parameter Symbol Test Condition Min Typ Max Unit
Si8642Bx, Ex
VDD1
VDD2
VDD1
VDD2
VI = 0(Bx), 1(Ex)
VI = 0(Bx), 1(Ex)
VI = 1(Bx), 0(Ex)
VI = 1(Bx), 0(Ex)
—
—
—
—
1.8
1.8
4.4
4.4
2.9
2.9
6.6
6.6
mA
1 Mbps Supply Current (All Inputs = 500 kHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
2.9
5.0
4.0
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.4
3.3
4.8
4.6
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.3
3.3
4.6
4.6
mA
10 Mbps Supply Current (All Inputs = 5 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
3.1
5.0
4.3
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
3.5
3.4
4.8
4.8
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
3.4
3.4
4.8
4.8
mA
100 Mbps Supply Current (All Inputs = 50 MHz Square Wave, CI = 15 pF on All Outputs)
Si8640Bx, Ex, Si8645Bx
VDD1
VDD2
—
—
3.6
9.9
5.0
12.8
mA
Si8641Bx, Ex
VDD1
VDD2
—
—
5.2
8.5
7.0
11.1
mA
Si8642Bx, Ex
VDD1
VDD2
—
—
6.9
6.9
9.0
9.0
mA
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 21
Parameter Symbol Test Condition Min Typ Max Unit
Timing Characteristics
Si864xBx, Ex
Maximum Data Rate 0 — 150 Mbps
Minimum Pulse Width — — 5.0 ns
Propagation Delay tPHL, tPLH See Figure 4.2 Propagation
Delay Timing on page 16
5.0 8.0 14 ns
Pulse Width Distortion
|tPLH -tPHL|
PWD See Figure 4.2 Propagation
Delay Timing on page 16 — 0.2 5.0 ns
Propagation Delay Skew 2 tPSK(P-P) — 2.0 5.0 ns
Channel-Channel Skew tPSK — 0.4 2.5 ns
All Models
Output Rise Time tr
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Output Fall Time tf
CL = 15 pF
See Figure 4.2 Propagation
Delay Timing on page 16
— 2.5 4.0 ns
Peak Eye Diagram Jitter tJIT(PK) See Figure 2.3 Eye Diagram
on page 7
— 350 — ps
Common Mode Transient Immunity
Si86xxxA/B/C/D
Si86xxxT
CMTI
VI = VDD or 0 V
VCM = 1500 V
See Figure 4.3 Common-
Mode Transient Immunity
Test Circuit on page 16
35
60
50
100
—
—
kV/µs
Enable to Data Valid ten1 See Figure 4.1 ENABLE
Timing Diagram on page 16
— 6.0 11 ns
Enable to Data Tri-State ten2 See Figure 4.1 ENABLE
Timing Diagram on page 16
— 8.0 12 ns
Input power loss to valid default output tSD See Figure 3.1 Device Be-
havior during Normal Opera-
tion on page 10
— 8.0 12 ns
Start-up Time 3 tSU — 15 40 µs
Note:
1. The nominal output impedance of an isolator driver channel is approximately 50 Ω, ±40%, which is a combination of the value of
the on-chip series termination resistor and channel resistance of the output driver FET. When driving loads where transmission
line effects will be a factor, output pins should be appropriately terminated with controlled-impedance PCB traces.
2. tPSK(P-P) is the magnitude of the difference in propagation delay times measured between different units operating at the same
supply voltages, load, and ambient temperature.
3. Start-up time is the time period from the application of power to the appearance of valid data at the output.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 22
Table 4.5. Regulatory Information1
CSA
The Si864x is certified under CSA Component Acceptance Notice 5A. For more details, see Master Contract Number 232873.
60950-1, 62368-1: Up to 600 VRMS reinforced insulation working voltage; up to 1000 VRMS basic insulation working voltage.
60601-1: Up to 250 VRMS working voltage and 2 MOPP (Means of Patient Protection).
VDE
The Si864x is certified according to VDE 0884-10. For more details, see certificates 40018443, 40037519.
0884-10: Up to 1200 Vpeak for basic insulation working voltage.
60950-1: Up to 600 VRMS reinforced insulation working voltage; up to 1000 VRMS basic insulation working voltage.
UL
The Si864x is certified under UL1577 component recognition program. For more details, see File E257455.
Rated up to 5000 VRMS isolation voltage for basic protection.
CQC
The Si864x is certified under GB4943.1-2011. For more details, see certificates CQC13001096110 and CQC13001096239.
Rated up to 600 VRMS reinforced insulation working voltage; up to 1000 VRMS basic insulation working voltage.
Note:
1. Regulatory Certifications apply to 2.5 kVRMS rated devices which are production tested to 3.0 kVRMS for 1 sec. Regulatory Certifi-
cations apply to 3.75 kVRMS rated devices which are production tested to 4.5 kVRMS for 1 sec. Regulatory Certifications apply to
5.0 kVRMS rated devices which are production tested to 6.0 kVRMS for 1 sec.
For more information, see 1. Ordering Guide.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 23
Table 4.6. Insulation and Safety-Related Specifications
Parameter Symbol Test Condition Value Unit
WB SOIC-16 NB SOIC-16 QSOP-16
Nominal External Air Gap (Clearance) 1 CLR 8.0 4.9 3.6 mm
Nominal External Tracking (Creepage) 1CPG 8.0 4.01 3.6 mm
Minimum Internal Gap
(Internal Clearance)
DTI 0.014 0.014 0.014 mm
Tracking Resistance CTI or PTI IEC60112 600 600 600 VRMS
Erosion Depth ED 0.019 0.019 0.031 mm
Resistance (Input-Output) 2 RIO 1012 1012 1012 Ω
Capacitance (Input-Output) 2 CIO f = 1 MHz 2.0 2.0 2.0 pF
Input Capacitance 3CI4.0 4.0 4.0 pF
Note:
1. The values in this table correspond to the nominal creepage and clearance values. VDE certifies the clearance and creepage
limits as 4.7 mm minimum for the NB SOIC-16 package and QSOP-16 packages and 8.5 mm minimum for the WB SOIC-16
package. UL does not impose a clearance and creepage minimum for component-level certifications. CSA certifies the clearance
and creepage of the WB SOIC-16 package with designation "IS2" as 8 mm minimum. CSA certifies the clearance and creepage
limits as 3.9 mm minimum for the NB SOIC 16, 3.6 mm minimum for the QSOP-16, and 7.6 mm minimum for the WB SOIC-16
package with package designation "IS" as listed in the data sheet.
2. To determine resistance and capacitance, the Si86xx is converted into a 2-terminal device. Pins 1–8 are shorted together to form
the first termina and pins 9–16 are shorted together to form the second terminal. The parameters are then measured between
these two terminals.
3. Measured from input pin to ground.
Table 4.7. IEC 60664-1 Ratings
Parameter Test Conditions Specification
WB SOIC-16 NB SOIC-16 QSOP-16
Basic Isolation Group Material Group I I I
Installation Classification Rated Mains Voltages < 150
VRMS
I-IV I-IV I-IV
Rated Mains Voltages < 300
VRMS
I-IV I-III I-III
Rated Mains Voltages < 400
VRMS
I-III I-II I-II
Rated Mains Voltages < 600
VRMS
I-III I-II I-II
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 24
Table 4.8. VDE 0884-10 Insulation Characteristics for Si86xxxx 1
Parameter Symbol Test Condition
Characteristic
Unit
WB SOIC-16 NB SOIC-16 QSOP-16
Maximum Working Insulation
Voltage VIORM 1200 630 630 Vpeak
Input to Output Test Voltage VPR
Method b1
(VIORM x 1.875 = VPR, 100%
Production Test, tm = 1 sec,
Partial Discharge < 5 pC)
2250 1182 1182 Vpeak
Transient Overvoltage VIOTM t = 60 sec 6000 6000 6000 Vpeak
Surge Voltage VIOSM
Tested per IEC 60065 with surge
voltage of 1.2 µs/50 µs
Si864xxT tested with magnitude
6250 V x 1.6 = 10 kV
Si864xxB/C/D tested with 4000 V
6250
3077
—
3077
—
3077
Vpeak
Pollution Degree
(DIN VDE 0110, Table 1)
2 2 2
Insulation Resistance at TS, VIO
= 500 V RS>109>109>109Ω
Note:
1. Maintenance of the safety data is ensured by protective circuits. The Si86xxxx provides a climate classification of 40/125/21.
Table 4.9. VDE 0884-10 Safety Limiting Values 1
Parameter Symbol Test Condition
Max
Unit
WB SOIC-16 NB SOIC-16 QSOP-16
Case Temperature TS150 150 150 °C
Safety Input, Output, or Supply
Current IS
θJA = 100 °C/W (WB SOIC-16)
105 °C/W (NB SOIC-16, QSOP-16)
VI = 5.5 V, TJ = 150 °C, TA = 25 °C
220 210 210 mA
Device Power Dissipation 2 PD275 275 275 mW
Note:
1. Maximum value allowed in the event of a failure; also see the thermal derating curve in Figure 4.4 (WB SOIC-16) Thermal Derat-
ing Curve, Dependence of Safety Limiting Values with Case Temperature per VDE 0884-10 on page 26 and Figure 4.5 (NB
SOIC-16, QSOP-16) Thermal Derating Curve, Dependence of Safety Limiting Values with Case Temperature per VDE 0884-10
on page 26.
2. The Si86xx is tested with VDD1 = VDD2 = 5.5 V; TJ = 150 ºC; CL = 15 pF, input a 150 Mbps 50% duty cycle square wave.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 25
Table 4.10. Thermal Characteristics
Parameter Symbol WB SOIC-16 NB SOIC-16/QSOP-16 Unit
IC Junction-to-Air Thermal Resistance θJA 100 105 °C/W
Figure 4.4. (WB SOIC-16) Thermal Derating Curve, Dependence of Safety Limiting Values with Case Temperature per VDE
0884-10
Figure 4.5. (NB SOIC-16, QSOP-16) Thermal Derating Curve, Dependence of Safety Limiting Values with Case Temperature
per VDE 0884-10
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 26
Table 4.11. Absolute Maximum Ratings 1
Parameter Symbol Min Max Unit
Storage Temperature 2 TSTG –65 150 °C
Operating Temperature TA–40 125 °C
Junction Temperature TJ— 150 °C
Supply Voltage VDD1, VDD2 –0.5 7.0 V
Input Voltage VI–0.5 VDD + 0.5 V
Output Voltage VO–0.5 VDD + 0.5 V
Output Current Drive Channel IO— 10 mA
Lead Solder Temperature (10 s) — 260 °C
Maximum Isolation (Input to Output) (1 sec)
NB SOIC-16, QSOP-16
— 4500 VRMS
Maximum Isolation (Input to Output) (1 sec)
WB SOIC-16
— 6500 VRMS
Note:
1. Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be restricted to
conditions as specified in the operational sections of this data sheet. Exposure to absolute maximum ratings for exteneded peri-
ods may degrade performance.
2. VDE certifies storage temperature from –40 to 150 °C.
Si864x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 2.13 | 27
5. Pin Descriptions
VDD1
GND1
A1
A3
A4
NC
GND1
A2
VDD2
GND2
B2
B1
B4
B3
GND2
EN2/NC
I
s
o
l
a
t
i
o
n
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
Si8640/45
VDD1
GND1
A1
A3
A4
EN1
GND1
A2
VDD2
GND2
B2
B1
B4
B3
GND2
EN2
I
s
o
l
a
t
i
o
n
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
Si8641
VDD1
GND1
A1
A3
A4
EN1
GND1
A2
VDD2
GND2
B2
B1
B4
B3
GND2
EN2
I
s
o
l
a
t
i
o
n
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
RF
RCVR
RF
XMITR
RF
RCVR
RF
XMITR
RF
RCVR
Si8642
Name SOIC-16 Pin# Type Description
VDD1 1 Supply Side 1 power supply.
GND1 21Ground Side 1 ground.
A1 3 Digital Input Side 1 digital input.
A2 4 Digital Input Side 1 digital input.
A3 5 Digital I/O Side 1 digital input or output.
A4 6 Digital I/O Side 1 digital input or output.
EN1/NC27 Digital Input Side 1 active high enable. NC on Si8640/45.
GND1 81Ground Side 1 ground.
GND2 91Ground Side 2 ground.
EN2/NC210 Digital Input Side 2 active high enable. NC on Si8645.
B4 11 Digital I/O Side 2 digital input or output.
B3 12 Digital I/O Side 2 digital input or output.
B2 13 Digital Output Side 2 digital output.
B1 14 Digital Output Side 2 digital output.
GND2 151Ground Side 2 ground.
VDD2 16 Supply Side 2 power supply.
Note:
1. For narrow-body devices, Pin 2 and Pin 8 GND must be externally connected to respective ground. Pin 9 and Pin 15 must also be
connected to external ground.
2. No Connect. These pins are not internally connected. They can be left floating, tied to VDD or tied to GND.
Si864x Data Sheet
Pin Descriptions
silabs.com | Building a more connected world. Rev. 2.13 | 28
6. Package Outline (16-Pin Wide Body SOIC)
The figure below illustrates the package details for the the Si86xx digital isolator in a 16-pin wide-body SOIC package. The table lists
the values for the dimensions shown in the illustration.
Figure 6.1. 16-Pin Wide Body SOIC
Si864x Data Sheet
Package Outline (16-Pin Wide Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 29
Table 6.1. 16-Pin Wide Body SOIC Package Diagram Dimensions
Dimension Min Max
A — 2.65
A1 0.10 0.30
A2 2.05 —
b 0.31 0.51
c 0.20 0.33
D 10.30 BSC
E 10.30 BSC
E1 7.50 BSC
e 1.27 BSC
L 0.40 1.27
h 0.25 0.75
θ 0° 8°
aaa — 0.10
bbb — 0.33
ccc — 0.10
ddd — 0.25
eee — 0.10
fff — 0.20
Note:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to JEDEC Outline MS-013, Variation AA.
4. Recommended reflow profile per JEDEC J-STD-020 specification for small body, lead-free components.
Si864x Data Sheet
Package Outline (16-Pin Wide Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 30
7. Land Pattern (16-Pin Wide Body SOIC)
The figure below illustrates the recommended land pattern details for the Si86xx in a 16-pin wide-body SOIC package. The table lists
the values for the dimensions shown in the illustration.
Figure 7.1. 16-Pin Wide Body SOIC PCB Land Pattern
Table 7.1. 16-Pin Wide Body SOIC Land Pattern Dimensions
Dimension Feature (mm)
C1 Pad Column Spacing 9.40
E Pad Row Pitch 1.27
X1 Pad Width 0.60
Y1 Pad Length 1.90
Note:
1. This Land Pattern Design is based on IPC-7351 pattern SOIC127P1032X265-16AN for Density Level B (Median Land Protru-
sion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card fabrication tolerance of 0.05 mm is assumed.
Si864x Data Sheet
Land Pattern (16-Pin Wide Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 31
8. Package Outline (16-Pin Narrow Body SOIC)
The figure below illustrates the package details for the Si86xx in a 16-pin narrow-body SOIC package. The table lists the values for the
dimensions shown in the illustration.
Figure 8.1. 16-Pin Narrow Body SOIC
Si864x Data Sheet
Package Outline (16-Pin Narrow Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 32
Table 8.1. 16-Pin Narrow Body SOIC Package Diagram Dimensions
Dimension Min Max
A — 1.75
A1 0.10 0.25
A2 1.25 —
b 0.31 0.51
c 0.17 0.25
D 9.90 BSC
E 6.00 BSC
E1 3.90 BSC
e 1.27 BSC
L 0.40 1.27
L2 0.25 BSC
h 0.25 0.50
θ 0° 8°
aaa 0.10
bbb 0.20
ccc 0.10
ddd 0.25
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MS-012, Variation AC.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
Si864x Data Sheet
Package Outline (16-Pin Narrow Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 33
9. Land Pattern (16-Pin Narrow Body SOIC)
The figure below illustrates the recommended land pattern details for the Si86xx in a 16-pin narrow-body SOIC package. The table lists
the values for the dimensions shown in the illustration.
Figure 9.1. 16-Pin Narrow Body SOIC PCB Land Pattern
Table 9.1. 16-Pin Narrow Body SOIC Land Pattern Dimensions1, 2
Dimension Feature (mm)
C1 Pad Column Spacing 5.40
E Pad Row Pitch 1.27
X1 Pad Width 0.60
Y1 Pad Length 1.55
Note:
1. This Land Pattern Design is based on IPC-7351 pattern SOIC127P600X165-16N for Density Level B (Median Land Protrusion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card fabrication tolerance of 0.05 mm is assumed.
Si864x Data Sheet
Land Pattern (16-Pin Narrow Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 34
10. Package Outline (16-Pin QSOP)
The figure below illustrates the package details for the Si86xx in a 16-pin QSOP package. The table lists the values for the dimensions
shown in the illustration.
Figure 10.1. 16-Pin QSOP Package
Si864x Data Sheet
Package Outline (16-Pin QSOP)
silabs.com | Building a more connected world. Rev. 2.13 | 35
Table 10.1. 16-Pin QSOP Package Diagram Dimensions1, 2, 3, 4
Dimension Min Max
A — 1.75
A1 0.10 0.25
A2 1.25 —
b 0.20 0.30
c 0.17 0.25
D 4.89 BSC
E 6.00 BSC
E1 3.90 BSC
e 0.635 BSC
L 0.40 1.27
L2 0.25 BSC
h 0.25 0.50
θ 0° 8°
aaa 0.10
bbb 0.20
ccc 0.10
ddd 0.25
Note:
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MO-137, Variation AB.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
Si864x Data Sheet
Package Outline (16-Pin QSOP)
silabs.com | Building a more connected world. Rev. 2.13 | 36
11. Land Pattern (16-Pin QSOP)
The figure below illustrates the recommended land pattern details for the Si86xx in a 16-pin QSOP package. The table lists the values
for the dimensions shown in the illustration.
Figure 11.1. 16-Pin QSOP PCB Land Pattern
Table 11.1. 16-Pin QSOP Land Pattern Dimensions1, 2
Dimension Feature (mm)
C1 Pad Column Spacing 5.40
E Pad Row Pitch 0.635
X1 Pad Width 0.40
Y1 Pad Length 1.55
Note:
1. This Land Pattern Design is based on IPC-7351 pattern SOP63P602X173-16N for Density Level B (Median Land Protrusion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card fabrication tolerance of 0.05 mm is assumed.
Si864x Data Sheet
Land Pattern (16-Pin QSOP)
silabs.com | Building a more connected world. Rev. 2.13 | 37
12. Top Marking (16-Pin Wide Body SOIC)
Si86XYSV
YYWWRTTTTT
TW
e4
Figure 12.1. 16-Pin Wide Body SOIC Top Marking
Table 12.1. 16-Pin Wide Body SOIC Top Marking Explanation
Line 1 Marking:
Base Part Number
Ordering Options
(See 1. Ordering Guide for more information).
Si86 = Isolator product series
XY = Channel Configuration
X = # of data channels (4)
Y = # of reverse channels (5, 2, 1, 0)1
S = Speed Grade (max data rate) and operating mode:
B = 150 Mbps (default output = low)
E = 150 Mbps (default output = high)
V = Insulation rating
A = 1 kV; B = 2.5 kV; C = 3.75 kV; D = 5.0 kV; T = 5.0 kV with
10 kV surge capability.
Line 2 Marking:
YY = Year
WW = Workweek
Assigned by assembly subcontractor. Corresponds to the year
and workweek of the mold date.
RTTTTT = Mfg Code
Manufacturing code from assembly house.
“R” indicates revision.
Line 3Marking:
Circle = 1.7 mm Diameter
(Center-Justified)
“e4” Pb-Free Symbol.
Country of Origin ISO Code Abbreviation TW = Taiwan as shown, TH = Thailand
Note:
1. Si8645 has 0 reverse channels.
Si864x Data Sheet
Top Marking (16-Pin Wide Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 38
13. Top Marking (16-Pin Narrow Body SOIC)
Si86XYSV
YYWWRTTTTT
e3
Figure 13.1. 16-Pin Narrow Body SOIC Top Marking
Table 13.1. 16-Pin Narrow Body SOIC Top Marking Explanation
Line 1 Marking:
Base Part Number
Ordering Options
(See 1. Ordering Guide for more information).
Si86 = Isolator product series
XY = Channel Configuration
X = # of data channels (4)
Y = # of reverse channels (5, 2, 1, 0)1
S = Speed Grade (max data rate) and operating mode:
B = 150 Mbps (default output = low)
E = 150 Mbps (default output = high)
V = Insulation rating
A = 1 kV; B = 2.5 kV; C = 3.75 kV
Line 2 Marking:
Circle = 1.2 mm Diameter “e3” Pb-Free Symbol
YY = Year
WW = Work Week
Assigned by the assembly subcontractor. Corresponds to the
year and work week of the mold date.
RTTTTT = Mfg Code
Manufacturing code from assembly house.
“R” indicates revision.
Note:
1. Si8645 has 0 reverse channels.
Si864x Data Sheet
Top Marking (16-Pin Narrow Body SOIC)
silabs.com | Building a more connected world. Rev. 2.13 | 39
14. Top Marking (16-Pin QSOP)
Figure 14.1. 16-Pin QSOP Top Marking
Table 14.1. 16-Pin QSOP Top Marking Explanation
Line 1 Marking:
Base Part Number
Ordering Options
(See 1. Ordering Guide for more information.)
86 = Isolator product series
XY = Channel Configuration
X = # of data channels (4)
Y = # of reverse channels (5, 2, 1, 0)1
S = Speed Grade (max data rate) and operating mode:
B = 150 Mbps (default output = low)
E = 150 Mbps (default output = high)
V = Insulation rating.
A = 1 kV; B = 2.5 kV; C = 3.75 kV
Line 2 Marking: RTTTTT = Mfg Code
Manufacturing code from assembly house.
“R” indicates revision.
Line 3 Marking:
YY = Year
WW = Work Week
Assigned by the Assembly House. Corresponds to the year and
work week of the mold date.
Note:
1. Si8645 has 0 reverse channels.
Si864x Data Sheet
Top Marking (16-Pin QSOP)
silabs.com | Building a more connected world. Rev. 2.13 | 40
15. Revision History
Revision 2.13
September 2018
•Added SI8640BB-AS, SI8641BC-AS1, and SI8642ED-AS to Ordering Guide for Automotive-Grade OPN options
Revision 2.12
February 2018
• Added SI8641BD-AS to Ordering Guide for Automotive-Grade OPN options
Revision 2.11
November 2017
• Added new table to Ordering Guide for Automotive-Grade OPN options
Revision 2.1
October 18, 2017
• Added new OPNs in Ordering Guide for IU (QSOP) and IS2 (8 mm creepage WB SOIC) package options.
• Added 62368-1 references throughout.
• Removed 61010-1 references throughout.
Revision 2.0
November 30, 2016
•Added note to Table 1.1 Ordering Guide for Valid OPNs1, 2 on page 2 for denoting tape and reel marking.
Revision 1.9
November 18, 2015
• Deleted duplicate Si8641BB-B-IU OPN listing and corrected Si8645BB-B-IU listing in 1. Ordering Guide.
• Added QSOP-16 information to Table 4.7 IEC 60664-1 Ratings on page 24.
•Added QSOP-16 information to Table 4.8 VDE 0884-10 Insulation Characteristics for Si86xxxx 1 on page 25.
•Added QSOP-16 information to Table 4.9 VDE 0884-10 Safety Limiting Values 1 on page 25.
• Added QSOP-16 reference to Figure 4.5 (NB SOIC-16, QSOP-16) Thermal Derating Curve, Dependence of Safety Limiting Values
with Case Temperature per VDE 0884-10 on page 26.
Revision 1.8
October 29, 2015
• Added product options Si8641BB-B-IU, Si8645BB-B-IU and Si864xxT in 1. Ordering Guide.
• Added spec line items for Input and Enable Leakage Currents pertaining to Si864xxT in Electrical Specifications.
• Added new spec for tSD in 4. Electrical Specifications.
• Updated IEC 60747-5-2 to IEC 60747-5-5 throughout document.
Revision 1.7
June 18, 2015
• Updated Table 5 on page 14.
• Added CQC certificate numbers.
• Updated "4. Ordering Guide" on page 10.
• Added Si8640BA OPN.
• Removed references to moisture sensitivity levels.
• Removed Note 2.
Si864x Data Sheet
Revision History
silabs.com | Building a more connected world. Rev. 2.13 | 41
Revision 1.6
September 25, 2013
•Added Figure 3, “Common Mode Transient Immunity Test Circuit,” on page 7.
• Added references to CQC throughout.
• Added references to 2.5 kVRMS devices throughout.
• Updated "4. Ordering Guide" on page 10.
• Updated "11.1. Top Marking (16-Pin Wide Body SOIC)" on page 20.
Revision 1.5
October 3, 2012
• Updated "4. Ordering Guide" on page 10.
• Updated "11.5. Top Marking (16-Pin QSOP)" on page 22.
Revision 1.4
June 26, 2012
• Updated Table 11 on page 18.
• Added junction temperature spec.
• Updated "2.3.1. Supply Bypass" on page 7.
• Removed “3.3.2 Pin Connections” on page 23.
• Updated "3. Pin Descriptions" on page 9.
• Updated table notes.
• Updated "4. Ordering Guide" on page 10.
• Removed Rev A devices.
• Updated "5. Package Outline: 16-Pin Wide Body SOIC" on page 12.
• Updated Top Marks.
• Added revision description.
Revision 1.3
March 21, 2012
• Updated "4. Ordering Guide" on page 10 to include MSL2A.
Revision 1.2
February 15, 2012
• Updated Table 3, “Ordering Guide for Valid OPNs” on page 10.
• Updated Note 1 with MSL2A.
• Updated Current Revision Devices.
Revision 1.1
September 14, 2011
• Updated High Level Output Voltage VOH to 3.1 V in Table 3, “Electrical Characteristics,” on page 8.
• Updated High Level Output Voltage VOH to 2.3 V in Table 4, “Electrical Characteristics,” on page 11.
Revision 1.0
July 14, 2011
• Reordered spec tables to conform to new convention.
• Removed “pending” throughout document.
Si864x Data Sheet
Revision History
silabs.com | Building a more connected world. Rev. 2.13 | 42
Revision 0.2
March 31, 2011
•Added chip graphics on page 1.
• Moved Tables 1 and 11 to page 18.
• Updated Table 6, “Insulation and Safety-Related Specifications,” on page 15.
• Updated Table 8, “IEC 60747-5-5 Insulation Characteristics for Si86xxxx*,” on page 16.
• Moved Table 1 to page 4.
• Moved Table 2 to page 5.
• Moved “Typical Performance Characteristics” to page 8.
• Updated "3. Pin Descriptions" on page 9.
• Updated "4. Ordering Guide" on page 10.
Revision 0.1
September 15, 2010
• Initial release.
Si864x Data Sheet
Revision History
silabs.com | Building a more connected world. Rev. 2.13 | 43
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Smart.
Connected.
Energy-Friendly.
Products
www.silabs.com/products
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
Disclaimer
Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or
intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"
parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes
without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included
information. Silicon Labs shall have no liability for the consequences of use of the information supplied herein. This document does not imply or express copyright licenses granted
hereunder to design or fabricate any integrated circuits. The products are not designed or authorized to be used within any Life Support System without the specific written consent of
Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected to result in significant
personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no circumstances be used in weapons of mass
destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®,
EFM32®, EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®,
Gecko®, ISOmodem®, Micrium, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress®, Zentri, Z-Wave and others are trademarks or
registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered trademark of ARM Limited.
All other products or brand names mentioned herein are trademarks of their respective holders.
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Silicon Laboratories:
Si8640BC-B-IS1 Si8640BD-B-IS Si8640EC-B-IS1 Si8640ED-B-IS Si8641BA-B-IU Si8641BC-B-IS1 Si8641BD-B-IS
Si8641EC-B-IS1 Si8641ED-B-IS Si8642BA-B-IU Si8642BC-B-IS1 Si8642BD-B-IS Si8642EC-B-IS1 Si8642ED-B-IS
Si8645BA-B-IU Si8645BC-B-IS1 Si8645BD-B-IS Si8641BB-B-IS1 Si8642BB-B-IS1 Si8640BB-B-IS1 Si8640BB-B-
ISR Si8645BB-B-IS1 Si8640BB-B-IS1R Si8640BB-B-IS Si8641BB-B-ISR Si8641BB-B-IS1R Si8642BB-B-ISR
Si8642BB-B-IS1R Si8641BB-B-IS Si8645BB-B-ISR Si8645BB-B-IS Si8645BB-B-IS1R Si8642BB-B-IS Si8642BA-A-
IU Si8641BA-C-IU Si8641BA-C-IUR Si8640ET-IS Si8641ET-IS Si8645BT-IS Si8645BT-ISR Si8641BT-ISR
Si8642BT-ISR Si8640BT-ISR Si8641BT-IS Si8645ET-ISR Si8641ET-ISR Si8642ET-ISR Si8640ET-ISR Si8642BT-
IS Si8642ET-IS Si8645ET-IS Si8640BT-IS
