CrouzetMotors.book Page 1 Wednesday, July 7, 2004 2:51 PM D.C. Motors 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/1 CrouzetMotors.book Page 2 Wednesday, July 7, 2004 2:51 PM DC Motors Selection guide Torque max (N m) Gearbox Speed Type of Gearbox 0.5 1.2 81 012 81 021 81 032.1 Direct Motors Power usable (w) 3 Torque nominal (mN.m) Speed nominal (rpm ) Voltage supply (V) 12 7.7 3700 24 8.7 41.5 9.4 45 12 2000 12 24 2580 12 2750 24 45 13 16 75 2000 12 24 20 2670 12 22 3070 24 20 2670 12 3070 24 70 70 22 27 172 12 1500 24 32 3100 12 33 3200 24 47 2630 12 50 2770 24 90 3200 24 3360 48 100 170 270 95 Type of motor dimensions (mm) p. 4 82 860 0 p.18 82 862 p.16 82 861 O 32 1.5 ... 441 rpm p. 8 0.36... 430 rpm 82 810 0 p.20 82 812 O 42 20... 130 rpm p. 6 82 810 5 O 42 p. 8 82 800 0 p.20 82 802 O 42 20... 130 rpm p. 6 82 800 5 O 42 p.10 82 800 8 O 42 p.12 82 830 0 O 63 p.10 82 850 0 O 42 p.12 82 830 5 O 63 p.14 82 890 0 O 63 Selection of a geared motor This choice is based upon the desired usable power at the gearbox output shaft 2 Power = ------ C n 60 (W) (Nm) (Rpm) A geared motor must have usable power equal to or greater than the power required to rotate the load desired. It is selected by checking that the point corresponding to the required operating conditions (torque and speed output) is higher than the nominal torque versus speed curve of the geared motor. The required torque output of a geared motor must be within its maximum recommended torque for continuous duty. Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/2 CrouzetMotors.book Page 3 Wednesday, July 7, 2004 2:51 PM 2 5 81 033 p.22 81 043 82 869 0.9 ... 108 rpm p.26 81 044 82 863 p.28 6 81 035 81 035 81 037 82 864 99... 662 rpm 80 813 p.24 2... 66 rpm p.30 80 814 60... 400 rpm 1... 40 rpm 10.5... 616 rpm p.24 80 803 60... 400 rpm p.30 80 804 1... 40 rpm p.34 p.34 80 815 80 805 10.5... 616 rpm p.38 80 835 p.32 81 032 6 82 867 1.72... 344 rpm p.36 80 817 1.04... 208 rpm 4 / 8 / 12 rpm p.36 80 807 1.04... 208 rpm p.42 82 812 82 802 4 / 8 / 12 rpm 7.4... 426 rpm p.42 p.44 82 832 5... 69 rpm p.40 80 855 13.8... 805 rpm 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/3 CrouzetMotors.book Page 4 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 32 mm 3.9 Watts A range of small 32 mm diameter D.C. direct-drive brushed motors with 3.9 Watts output power. Available in either 12 or 24 V D.C. versions. Sintered bronze bearings lubricated for life. Connection by 2.8 mm push-on terminals. Interference suppression fitted as standard. Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection rating Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Sintered bronze bearings 3.9 Watts 3.9 Watts with encoder 1 pulse/revolution 3.9 Watts 3.9 Watts with encoder 1 pulse/revolution 82 860 0 12 V 82 860 003 82 860 0 12 V 82 860 501 82 860 0 24 V 82 860 004 82 860 0 24 V 82 860 502 5000 1.2 0.1 5000 1.2 0.1 5000 1.92 0.08 5000 1.92 0.08 3700 7.7 3 6.2 0.43 50 48 3700 7.7 3 6.2 0.43 50 48 3700 7.7 3 6 0.26 50 50 3700 7.7 3 6 0.26 50 50 B (130 C) B (130C) B (130 C) B (130C) IP40 3.9 30 1.5 8 10 0.0214 1.3 36 8 19 96 3 3000 IP 40 3.9 30 1.5 8 10 0.0214 1.3 36 8 19 96 3 3000 IP40 3.9 30 0.76 32 41.6 0.0448 1.3 36 8 19 95 3 3000 IP 40 3.9 30 0.76 32 41.6 0.0448 1.3 36 8 19 95 3 3000 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/4 CrouzetMotors.book Page 5 Wednesday, July 7, 2004 2:51 PM Curves A - Nominal speed and torque curves B - Torque/Current curves 82 860 0 82 860 0 A B mN.m mN.m 24 V 30 30 20 12 V 20 12V-24V 10 10 1 0 0 1000 3000 A 0 5000 0 0.4 0.8 1.2 1.6 B RPM Dimensions 82 860 0 2 44.6 max. 1 B 2 tags NFC 20 - 120 series 2.8 x 0.5 mm C 3 holes at 120 on O 26 mm : use self tapping screws M2.2 ; screw depth max 6 mm 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/5 CrouzetMotors.book Page 6 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 42 mm 14 to 31 Watts A range of 42 mm diameter D.C. direct-drive brushed motors with 14 to 31 W output power. Available in either 12 or 24 V D.C. versions. Sintered bronze bearings lubricated for life Replaceable brushes Magnetic encoder option Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection (IEC 529) Housing Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Sintered bronze bearings Replaceable brushes (mm) 14 Watts 16 Watts 22 Watts 31 Watts 82 810 5 12 V 82 810 501 82 810 5 24 V 82 810 502 82 800 5 12 V 82 800 501 82 800 5 24 V 82 800 502 3840 12 1 3860 11.28 0.47 3920 9.96 0.83 4010 12.24 0.51 2580 45 12 31 2.6 32 39 2750 45 13 32 1.32 33 40.8 2670 70 20 37 3.05 38 54 3070 70 22 41 1.71 40 54 F (155 C) F (155 C) F (155 C) F (155 C) IP20 14 138 6.2 1.94 4.45 0.0265 2.3 26 8 80 310 8 2000 IP20 16 156 3.4 7.06 16.94 0.0532 2.4 23 8 72 310 8 2000 IP20 22 219 9 1.33 2.67 0.0268 2 20 12 105 400 8 2000 IP20 31 298 6.16 3.9 9.35 0.0527 2.4 15 12 110 400 8 2000 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/6 CrouzetMotors.book Page 7 Wednesday, July 7, 2004 2:51 PM Curves A - Torque/Speed curves B - Torque/Current curves 82 810 5 82 810 5 82 800 5 A B mN.m 200 24V 12V 50 350 24V 250 120 100 mN.m 300 140 100 B A mN.m 160 24V 150 82 800 5 300 250 200 12V 80 150 12V 60 100 150 0 0 1000 2000 3000 A 0 0 1 2 3 B RPM 4 5 6 12V 100 50 20 24V 200 40 1 mN.m 1 0 50 A 0 0 1000 2000 3000 0 1 2 3 4 5 6 7 8 9 B RPM Dimensions 82 810 5 69.8 max. 1 3 2 B 2 M3 at 180 depth 5 mm on O 32 C 2 x O 2.75 at 120 depth 5 mm on O 32 D 2 tags IEC 760 series 4.8 x 0.5 mm 82 800 5 84.8 max. 1 2 4 3 B 2 M3 at 180 depth 5 mm on O 32 C 2 x O 2.75 at 120 depth 5 mm on O 32 D 2 tags IEC 760 series 4.8 x 0.5 mm Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/7 CrouzetMotors.book Page 8 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 42 mm 10 to 17 Watts A range of 42 mm diameter D.C. direct-drive brushed motors with 10 or 17 Watts output power. Available in either 12, 24 or 48V D.C. versions Sintered bronze bearings lubricated for life Supply connection by 4.75 mm tags Replaceable brushes Optional magnetic encoder Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection (IEC 529) Housing Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Sintered bronze bearings Replaceable brushes (mm) 10 Watts 10 Watts 17 Watts 17 Watts 82 810 0 12 V 82 810 017 82 810 0 24 V 82 810 018 82 800 0 12 V 82 800 036 82 800 0 24 V 82 800 037 2850 4.8 0.4 2780 4.3 0.18 2960 4.8 0.4 2750 4.3 0.18 2000 45 9.4 20.4 1.7 45 46 2000 41.5 8.7 15.6 0.65 46 55.7 2000 75 15.7 30 2.5 44 52 2000 75 15.6 26.4 1.1 40 59 F (155 C) F (155 C) F (155 C) F (155 C) IP20 10.3 127 4 3.1 2.5 0.035 0.8 19 10 80 310 8 3000 IP20 9.5 117 1.7 14.6 10.7 0.077 0.73 17 10 72 310 8 3000 IP20 16.3 185 5.8 2 1.8 0.0342 0.89 18 12 105 400 8 3000 IP20 17 210 2.7 7.7 6.9 0.0724 0.89 16 12 110 400 8 3000 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/8 CrouzetMotors.book Page 9 Wednesday, July 7, 2004 2:51 PM Curves A - Torque/Speed curves B - Torque/Current curves 82 810 0 82 810 0 82 800 0 A 82 800 0 A B mN.m mN.m 120 120 48V 12V 24V 48V 24V 12V 200 24V - 48V 150 24V B mN.m mN.m 200 150 80 80 48V 100 100 12V 40 40 50 50 12V 1 0 0 1000 2000 3000 A 0 0 1 2 B RPM 3 4 1 0 0 1000 2000 3000 A 0 0 2 4 6 B RPM Dimensions 82 810 0 69.8 max. 1 3 2 B 2 M3 at 180 depth 5 mm on O 32 C 2 holes x O 2.75 at 120 C depth 5 mm O 32 D 2 tags IEC 760 series 4.8 x 0.5 mm 0.05 82 800 0 84.8 max. 1 4 3 2 B 2 M3 at 180 depth 5 mm on O 32 C 2 x O 2.75 at 120 depth 5 mm O 32 D 2 tags IEC 760 series 4.8 x 0.5 mm 0.05 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/9 CrouzetMotors.book Page 10 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 42 mm 22 to 52 Watts A range of 42 mm diameter D.C. direct-drive brushed motors with 22 to 52 Watts output power. Available in either 12 or 24 V D.C. versions. Sintered bronze bearings lubricated for life Supply connection by 2 leads Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection (IEC 529) Terminal Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Sintered bronze bearings Wires length (mm) 22 Watts 31 Watts 42 Watts 52 Watts 82 800 8 12 V 82 800 801 82 800 8 24 V 82 800 802 82 850 0 12 V 82 850 001 82 850 0 24 V 82 850 002 3920 9.96 0.83 4010 12.24 0.51 4150 7.32 0.61 4050 7.44 0.31 2670 70 20 37 3.05 38 54 3070 70 22 41 1.71 40 54 3100 100 32.5 51 4.25 63 63 3200 100 33.5 52 2.15 54 64 F (155 C) F (155 C) F (155 C) F (155 C) IP20 22 219 9 1.33 2.67 0.0268 2 20 12 105 400 8 3000 IP20 31 298 6.16 3.9 9.35 0.0527 2.4 15 12 110 400 8 3000 IP20 42 390 14.8 0.81 0.7 0.027 0.85 16 26 140 640 8 3000 IP20 52 490 9.6 2.5 2.5 0.052 1 13 21 140 640 8 3000 200 200 200 200 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/10 CrouzetMotors.book Page 11 Wednesday, July 7, 2004 2:51 PM Curves A - Torque/Speed curves B - Torque/Current curves 82 800 8 82 800 8 82 850 0 B A mN.m 300 350 24V 250 200 mN.m mN.m 500 500 24V 24 V 24 V 200 150 12V 250 250 150 100 12 V 12V 12 V 100 50 1 0 1 50 A 0 1000 B A mN.m 300 250 0 82 850 0 2000 3000 0 1 2 3 4 0 0 2000 0 5 6 7 8 9 B RPM A 0 4000 8 16 B RPM Dimensions 82 800 8 3 1 4 2 B 2 holes M3 x 0.5 at 180 depth 5 on O 32 C 2 holes 2.75 0.05 at 120 depth 5 mm on O 32 D 2 holes M3 x 0.5 at 180 depth 5.5 on O 32 E 2 holes M3 x 0.5 at 120 depth 5.5 on O 32 82 850 0 1 3 4 2 4 B 2 holes M3 x 0.5 at 180 depth 5 mm on O 32 C 2 holes 2.75 0.05 at 120 depth 5 mm on O 32 D 2 holes M3 x 0.5 at 180 depth 5.5 mm on O 32 E 2 holes M3 x 0.5 at 120 depth 5.5 mm on O 32 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/11 CrouzetMotors.book Page 12 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 63 mm 33 to 67 Watts A range of 63mm diameter D.C. direct-drive brushed motors with 33 to 67 W output power. Available in either 12, 24 or 48V D.C. versions. Ball bearings on output shaft Supply connection by 2 leads Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection (IEC 529) Terminal Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Ball bearings Wires length (mm) 33 watts 33 Watts 67 Watts 67 Watts 82 830 0 12 V 82 830 009 82 830 0 24 V 82 830 010 82 830 5 12 V 82 830 501 82 830 5 24 V 82 830 502 2100 4.8 0.4 2100 4.8 0.2 3400 12.6 1.05 3660 12 0.5 1500 172 27 43 3.6 50 62 1500 172 27 45 1.9 50 60 2630 170 47 72 6 46 65 2770 170 50 72 3 50 69.4 F (155 C) F (155 C) F (155 C) F (155 C) IP20 33 600 12 1 1.4 0.0517 1.4 19 37 514 840 12 5000 IP20 33 600 6.2 3.9 6.4 0.1 1.64 19 37 492 840 12 5000 IP20 67 750 23.1 0.52 1.19 0.034 2.3 33 20 520 840 12 4000 IP20 67 700 11.8 2.03 4.68 0.0619 2.3 33 18 500 840 12 4000 200 200 200 200 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/12 CrouzetMotors.book Page 13 Wednesday, July 7, 2004 2:51 PM Curves A - Torque/Speed curves B - Torque/Current curves 82 830 0 82 830 0 82 830 5 A 82 830 5 A B mN.m mN.m 48V 600 600 24V 12V 12V - 24V - 48V 200 200 700 600 600 500 24V 500 400 400 300 300 200 200 100 1 0 500 0 1000 1500 2000 A 0 0 3 6 9 1 0 0 12 B RPM 1000 mN.m 800 12V 700 400 400 B mN.m 800 2000 3000 24V 12V 100 A 0 0 3 6 9 12 15 18 21 B RPM Dimensions 82 830 0 1 3 2 B 4 holes O 3.65 at 90 on O 48 C 4 holes M5 on O 40 depth 7 mm D 4 holes M5 on O 40 depth 7 mm 0.05 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/13 CrouzetMotors.book Page 14 Wednesday, July 7, 2004 2:51 PM D.C. direct drive brushed motors O 63 mm 194 to 255 Watts A range of D.C. direct-drive brushed motors with a case diameter of 63 mm and between 194 and 255 Watts output power. Available in either 24 or 48V D.C. versions Ball bearings on output shaft Supply connection by 2 leads Specifications Type Voltage Part numbers No-load characteristics Speed of rotation (rpm) Absorbed power (W) Absorbed current (A) Nominal characteristics Speed (rpm) Torque (mN.m) Usable power (W) Absorbed power (W) Absorbed current (A) Gearbox case temperature rise (C) Efficiency (%) General characteristics Insulation class (conforming to IEC 85) Protection (IEC 529) Terminal Max. output (W) Start torque (mN.m) Starting current (A) Resistance () Inductance (mH) Torque constant (Nm/A) Electrical time constant (ms) Mechanical time constant (ms) Thermal time constant (min) Inertia (g.cm2 ) Weight (g) No of segments Service life (h) Ball bearings Wires length (mm) 194 Watts 255 Watts 82 890 0 24 V 82 890 001 82 890 0 48 V 82 890 002 3700 10.8 0.45 3750 9.6 0.2 3200 270 90 120 5.00 50 75 3360 270 95 118 2.45 50 80 F (155 C) IP20 194 2000 34.1 0.7 1.05 0.059 1.5 16 41 795 1580 12 5000 F (155 C) IP20 255 2600 21.7 2.2 4.62 0.12 2.1 12 36 795 1580 12 5000 200 200 Products adaptations, available on request Special output shafts Pinion on output shaft Special supply voltages Special cable lengths Special output bearings Optional encoder Special mounting plate Customized electronics Special connectors Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/14 CrouzetMotors.book Page 15 Wednesday, July 7, 2004 2:51 PM Curves A - Torque/Speed curves B - Torque/Current curves 82 890 0 mN.m 82 890 0 A 8 6 12 V 24 V 4 2 1 0 0 1000 B RPM 3000 5000 Dimensions 82 890 0 1 2 3 B 4 holes O 3.65 at 90 on O 48 C 4 holes M5 on O 40 depth 7 mm D 4 holes M5 on O 40 depth 7 mm 0.05 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/15 CrouzetMotors.book Page 16 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 0.5 Nm 3.9 Watts A range of D.C. geared motors with ovoid gearbox. Mechanical rating of gearbox with output shaft stalled : 0.5 Nm. 3.9 Watt motor versions. Available in either 12 or 24 V D.C. Gearbox ratios options for 0.36 to 430 rpm. Specifications Type Voltage Standard speed (rpm) Output speed (rpm) Ratios (i) 430 10 215 20 179 24 143 30 108 40 90 48 54 80 49 90 29 150 22 200 11 375 8.6 500 5.8 750 3.6 1200 1.8 2400 0.80 5400 0.36 12000 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (for 1 millions turns) Nm Axial load (static) daN Radial load (static) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 Watts 82 861 0 12 V 4300 82 861 0 24 V 4300 82 861 006 82 861 007 82 861 0X00024B 82 861 008 82 861 009 82 861 0X00048B 82 861 010 82 861 0X00090B 82 861 0X00150B 82 861 011 82 861 012 82 861 013 82 861 0X00750B 82 861 014 82 861 0X02400B 82 861 0X05400B 82 861 0X12000B 82 861 015 82 861 016 82 861 0Y00024B 82 861 017 82 861 018 82 861 0Y00048B 82 861 019 82 861 0Y00090B 82 861 0Y00150B 82 861 020 82 861 021 82 861 022 82 861 0Y00750B 82 861 023 82 861 0Y02400B 82 861 0Y05400B 82 861 0Y12000B 82 860 0 81 021 0 0.5 82 860 0 81 021 0 0.5 1 8 3.9 3 50 160 1 8 3.9 3 50 160 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/16 CrouzetMotors.book Page 17 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 3000 mN.m 1000 500 300 100 30 1 10 1 23 10 2030 100 200300 B RPM Dimensions 82 861 0 61.3 max. 3 4 1 2 B 2 fixing holes O 3.2 C 2 tags NFC 20-120 series 2.8 x 0.5 mm D (shaft pushed-in ) E 3.5 mm across flats Options Shaft 70 999 421 SP1295.10 1 Shaft 79 200 779 Shaft 79 200 967 1 1 2 4 B (shaft pushed-in ) C 5 across flat B (shaft pushed-in ) B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/17 CrouzetMotors.book Page 18 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 0.5 Nm 3.9 Watts A range of D.C. geared motors with sintered metal gears. Mechanical rating of gearbox with output shaft stalled : 0.5 Nm. 3.9 Watt motor power Available in either 12 or 24 V D.C. versions. Gearbox ratios options for 1.5 to 441 rpm. Options with magnetic encoder. Specifications Type Voltage Output speed (rpm) Ratios (i) 441 9.76 141 30.6 45 95.4 14 298 5 931 1.5 2910 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (for 1 millions turns) N.m Axial load (static) daN Radial load (static) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 Watts 82 862 0/2 12 V 82 862 0/2 24 V 82 862 001 82 862 002 82 862 003 82 862 201 82 862 202 82 862 203 82 862 004 82 862 005 82 862 006 82 862 204 82 862 205 82 862 206 82 860 0 81 012 0 / 81 012 2 0.5 82 860 0 81 012 0 / 81 012 2 0.5 1 8 3.9 3 50 160 / 170 1 8 3.9 3 50 160 / 170 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/18 CrouzetMotors.book Page 19 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 10000 82 862 0 1000 500 100 1 10 1 10 100 1000 B RPM Dimensions 82 862 0 1 24.3 68.1 3 4 2 B 4 mm across flats C (shaft pushed-in ) D 2 tags NFC 20-120 series 2.8 x 0.5 mm E 3 holes M3 depth 4.5 mm 82 862 2 1 35.1 4 78.9 3 2 B 4 mm across flats C (shaft pushed-in ) D 2 tags NFC 20-120 series 2.8 x 0.5 mm E 3 holes M3 depth 4.5 mm 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/19 CrouzetMotors.book Page 20 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 1.2 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears Mechanical rating of gearbox with output shaft stalled : 1.2 Nm 10 and 17 Watt motor power Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 20 to 100 rpm Specifications Type Voltage Output speed Ratios (i) (rpm) 100 26 80 32.5 60 130/3 38 67.6 30 598/7 20 130 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 10 millions turns Nm Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 17 Watts 17 Watts 10 Watts 10 watts 82 802 0 12 V 82 802 0 24 V 82 812 0 12 V 82 812 0 24 V 82 802 0X00026Z 82 802 0X032.5Z 82 802 0X43.33Z 82 802 0X067.6Z 82 802 0X85.43Z 82 802 0X00130Z 82 802 0Y00026Z 82 802 0Y032.5Z 82 802 0Y43.33Z 82 802 0Y067.6Z 82 802 0Y85.43Z 82 802 0Y00130Z 82 812 0X00026Z 82 812 0X032.5Z 82 812 0X43.33Z 82 812 0X067.6Z 82 812 0X85.43Z 82 812 0X00130Z 82 812 0Y00026Z 82 812 0Y032.5Z 82 812 0Y43.33Z 82 812 0Y067.6Z 82 812 0Y85.43Z 82 812 0Y00130Z 82 800 0 81 032 1 1.2 82 800 0 81 032 1 1.2 82 810 0 81 032 1 1.2 82 810 0 81 032 1 1.2 3.5 5 16.3 15.7 44 670 3.5 5 17 15.6 40 670 3.5 5 10.3 9.4 45 670 3.5 5 9.5 8.7 46 670 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/20 CrouzetMotors.book Page 21 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 82 802 0 Nominal speed and torque curves 82 812 0 mN.m mN.m 10000 10000 3000 3000 1000 1000 300 300 12V 24V-48V 1 1 100 100 3 10 20 30 3 100 200 300 B RPM 10 20 30 100 200 300 B RPM Dimensions 82 802 0 Standard 25.3 25.3 1 126 mm 1.85 7 -0 O8 -0.015 O12 4 85 max. 1.6 81.6 max. 29.1 14.5 21.5 27.25 39.7 19.85 19.85 3 25.1 25.1 15 26.9 max. 2 64.1 max. 5 B 4 holes M4 depth 7.5 mm C 3 holes M5 at 120 depth 7.5 mm D 2 tags IEC 760 series 4.8 x 0.5 mm E 7 mm across flats F (shaft pushed-in ) 82 812 0 Standard 25.3 25.3 1 111 mm 1.85 7 -0 O8 -0.015 O12 3 25.1 25.1 64.1 max. 2 4 4 1.6 81.6 max. 85 max. 29.1 14.5 21.5 27.25 39.7 19.85 19.85 15 26.9 max. 5 B 8 holes M4 depth 7.5 mm C 3 holes M5 at 120 depth 7.5 mm D 2 tags IEC 760 series 4.8 x 0.5 mm E 7 mm across flats F (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/21 CrouzetMotors.book Page 22 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 2 Nm 3.9 Watts A range of D.C. geared motors with ovoid gearbox. Mechanical rating of gearbox with output shaft stalled : 2 Nm. 3.9 Watt motor versions. Available in either 12 or 24 V D.C. Gearbox ratios options for 0.36 to 430 rpm. Alternative shaft options. Specifications Type Voltage Output speed (rpm) Ratios (i) 108 40 54 80 27 160 13 320 7.2 600 5.4 800 2.9 1500 0.90 4800 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 1 millions turns Nm Axial load (static) daN Radial load (static) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 Watts 82 869 0 12 V 82 869 0 24 V 82 869 001 82 869 006 82 869 007 82 869 008 82 869 009 82 869 0X00800X 82 869 010 82 869 0X04800X 82 869 011 82 869 012 82 869 013 82 869 014 82 869 015 82 869 0Y00800X 82 869 016 82 869 0Y04800X 82 860 0 81 033 0 2 82 860 0 81 033 0 2 1 10 3.9 3 50 240 1 10 3.9 3 50 240 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/22 CrouzetMotors.book Page 23 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 3000 2000 1000 300 100 30 1 10 0 1 23 10 2030 100 B RPM Dimensions 82 869 0 4 1 5 2 3 79.6 max. B 2 fixing holes O 3.2 C 3 bosses O 7.2 at 120 on R=19.5 with 3 M3 holes D 2 tags NFC 20-120 series 2.8 x 0.5 mm E (shaft pushed-in ) F 5 mm across flats Options Shaft 79 202 573 2 4 1 B (shaft pushed-in ) C 5 across flat Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/23 CrouzetMotors.book Page 24 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 2 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears Mechanical rating of gearbox with output shaft stalled : 1.2 Nm 10 and 17 Watt motor power Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 60 to 400 rpm Specifications Type Voltage Output speed Ratios (i) (rpm) 400 13/2 301 855/99 161 728/45 120 65/3 103 455/18 80 32.5 60 130/3 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 1 millions turns Nm Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 17 Watts 17 Watts 10 Watts 10 Watts 80 803 0 12 V 80 803 0 24 V 80 813 0 12 V 80 813 0 24 V 80 803 0X006.5Z 80 803 0X8.636Z 80 803 005 80 803 0X21.67Z 80 803 0X25.28Z 80 803 006 80 803 007 80 803 0Y006.5Z 80 803 0Y8.636Z 80 803 008 80 803 0Y21.67Z 80 803 0Y25.28Z 80 803 009 80 803 010 80 813 0X006.5Z 80 813 0X8.636Z 80 813 0X16.18Z 80 813 0X21.67Z 80 813 0X25.28Z 80 813 0X32.5Z 80 813 0X43.33Z 80 813 0Y006.5Z 80 813 0Y8.636Z 80 813 0Y16.18Z 80 813 0Y21.67Z 80 813 0Y25.28Z 80 813 0Y32.5Z 80 813 0Y43.33Z 82 800 0 81 043 0 2 82 800 0 81 043 0 2 82 810 0 81 043 0 2 82 810 0 81 043 0 2 2 2 16.3 15.7 44 600 2 2 17 15.6 40 600 2 2 10.3 9.4 45 500 2 2 9.5 8.7 46 500 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/24 CrouzetMotors.book Page 25 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 80 803 0 Nominal speed and torque curves 80 813 0 mN.m mN.m 2000 2000 1500 1500 1000 800 1000 800 600 500 400 600 500 400 300 300 200 200 1 1 50 60 80100 150 200 300 50 60 80 100 150 200 300 B RPM B RPM Dimensions 80 803 0 Standard 2 98.4 max. 3 1 B 2 tags IEC 760 series 4.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) 80 813 0 Standard 2 83.4 max. 4 3 1 B 2 tags IEC 760 series 4.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) Options Shaft 79 261 300 1 B (shaft pushed-in ) Shaft 79 261 309 1 B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/25 CrouzetMotors.book Page 26 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 2 Nm 3.9 Watts A range of D.C. geared motors with metal gearbox. Mechanical rating of gearbox with output shaft stalled : 2 Nm. 3.9 Watt motor power. Available in either 12 or 24 V D.C. Gearbox ratios options for 99 to 662 rpm. Specifications Type Voltage Output speed (rpm) Ratios (i) 662 13/2 498 855/99 266 728/45 198 65/3 170 455/18 132 32.5 99 130/3 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (for 1 millions turns) N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 Watts 82 863 0 12 V 82 863 0 24 V 82 863 0X006.5Z 82 863 0X8.636Z 82 863 0X16.18Z 82 863 0X21.67Z 82 863 0X25.28Z 82 863 0X032.5Z 82 863 0X43.33Z 82 863 0Y006.5Z 82 863 0Y8.636Z 82 863 0Y16.18Z 82 863 0Y21.67Z 82 863 0Y25.28Z 82 863 0Y032.5Z 82 863 0Y43.33Z 82 860 0 81 043 0 2 82 860 0 81 043 0 2 2 2 3.9 3 50 285 2 2 3.9 3 50 285 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/26 CrouzetMotors.book Page 27 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 5000 2000 1000 500 200 100 50 20 1 1 2 5 10 20 50 100 200 500 B RPM Dimensions 82 863 0 2 1 65.8 max. 3 B 2 tags NFC 20-120 series 2.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) Options Shaft 79 261 300 1 Shaft 79 261 309 1 4 B (shaft pushed-in ) B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/27 CrouzetMotors.book Page 28 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 2 Nm 3.9 Watts A range of D.C. geared motors with metal gearbox. Mechanical rating of gearbox with output shaft stalled : 2 Nm. 3.9 Watt motor versions. Available in either 12 or 24 V D.C. Gearbox ratios options for 2 to 66 rpm. Specifications Type Voltage Output speed (rpm) Ratios (i) 66 65 40 325/3 26 162.5 13 325 7 650 2 2600 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (for 1 millions turns) N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 Watts 82 864 0 12 V 82 864 0 24 V 82 864 0X00065Z 82 864 0X108.3Z 82 864 0X162.5Z 82 864 0X00325Z 82 864 0X00650Z 82 864 0X02600Z 82 864 0Y00065Z 82 864 0Y108.3Z 82 864 0Y162.5Z 82 864 0Y00325Z 82 864 0Y00650Z 82 864 0Y02600Z 82 860 0 81 044 0 2 82 860 0 81 044 0 2 2 2 3.9 3 50 355 2 2 3.9 3 50 355 Products adaptations Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/28 CrouzetMotors.book Page 29 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 5000 2000 1000 500 200 100 50 20 1 1 2 5 10 20 50 100 200 500 B RPM Dimensions 82 864 0 2 1 65.8 max. 3 B 2 tags NFC 20-120 series 2.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) Options Shaft 79 261 300 1 Shaft 79 261 309 Shaft 79 261 314 1 1 2 B (shaft pushed-in ) B (shaft pushed-in ) 4 2 B (shaft pushed-in ) C 7 across flat Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/29 CrouzetMotors.book Page 30 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 2 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 2 Nm. 10 and 17 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 1 to 40 rpm. Specifications Type Voltage Output speed Ratios (i) (rpm) 40 65 24 325/3 16 162.5 8 325 4 650 1 2600 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 1 millions turns Nm Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 17 Watts 17 Watts 10 Watts 10 Watts 80 804 0 12 V 80 804 0 24 V 80 814 0 12 V 80 814 0 24 V 80 804 0X00065Z 80 804 006 80 804 0X162.5Z 80 804 007 80 804 008 80 804 0X02600Z 80 804 0Y00065Z 80 804 009 80 804 0Y162.5Z 80 804 010 80 804 011 80 804 0Y02600Z 80 814 0X00065Z 80 814 0X108.3Z 80 814 0X162.5Z 80 814 0X00325Z 80 814 0X00650Z 80 814 0X02600Z 80 814 0Y00065Z 80 814 0Y108.3Z 80 814 0Y162.5Z 80 814 0Y00325Z 80 814 0Y00650Z 80 814 0Y02600Z 82 800 0 81 044 0 2 82 800 0 81 044 0 2 82 810 0 81 044 0 2 82 810 0 81 044 0 2 2 2 16.3 15.7 44 670 2 2 17 15.6 40 670 2 2 10.3 9.3 45 570 2 2 9.5 8.7 46 570 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/30 CrouzetMotors.book Page 31 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 80 804 0 Nominal speed and torque curves 80 814 0 mN.m mN.m 100 000 10000 30 000 1000 500 10 000 100 3 000 1 10 1 10 100 1 2 3 1000 B RPM 5 10 20 40 B RPM Dimensions 80 804 0 Standard 2 98.4 max. 1 3 B 2 tags IEC 760 series 4.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) 80 814 0 Standard 2 1 83.4 max. 3 4 B 2 tags IEC 760 series 4.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in) Options Shaft 79 261 300 1 Shaft 79 261 309 Shaft 79 261 314 1 1 2 B (shaft pushed-in ) B (shaft pushed-in ) 2 B (shaft pushed-in ) C 7 across flat Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/31 CrouzetMotors.book Page 32 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 5 Nm 3.9 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 5 Nm. 3.9 Watt motor versions. Available in either 12 or 24 V D.C. Gearbox ratios options for 1.7 to 344 rpm. Interference suppression on standard products Specifications Type Voltage Output speed (rpm) Ratios (i) 344 12.5 258 50/3 172 25 103 125/3 69 62.5 34 125 17 250 8.6 500 1.72 2500 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (for 1 millions turns) N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 3.9 Watts 3.9 watts 82 867 0 12 V 82 867 0 24 V 82 867 001 82 867 0X16.67Z 82 867 002 82 867 003 82 867 004 82 867 005 82 867 0X00250Z 82 867 006 82 867 0X2500Z 82 867 007 82 867 0Y16.67Z 82 867 008 82 867 009 82 867 010 82 867 011 82 867 0Y00250Z 82 867 012 82 867 0Y2500Z 82 860 0 81 037 0 5 82 860 0 81 037 0 5 2 3 3.9 3 50 465 2 3 3.9 3 50 465 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/32 CrouzetMotors.book Page 33 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 82 867 0 10000 5000 mN.m 2000 1000 500 200 100 50 20 1 1 2 5 10 20 50 100 200 500 B RPM Dimensions 82 867 0 3 79.8 max. 2 4 1 B 4 fixing holes O M4 x 12 mm C 2 tags NFC 20-120 series 2.8 x 0.5 mm D 7 mm 0.1 across flats E (shaft pushed-in ) Options Shaft 79 206 478 1 4 B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/33 CrouzetMotors.book Page 34 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 5 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 5 Nm. 10 and 17 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 10.5 to 616 rpm. Specifications Type Voltage Standard speed (rpm) Output speed Ratios (i) (rpm) 616 4.22 385 6.75 339.5 7.66 212 12.25 170 15.31 106 24.5 68 38.28 53 49 42.5 61.25 21 122.5 10.5 245 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (N.m) Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 17 Watts 17 Watts 10 Watts 10 Watts 80 805 0 12 V 2600 rpm 80 805 0 24 V 2600 rpm 80 815 0 12 V 2600 rpm 80 815 0 24 V 2600 rpm 80 805 0X04.22Z 80 805 0X06.75Z 80 805 0X07.66Z 80 805 0X12.25Z 80 805 0X15.31Z 80 805 0X024.5Z 80 805 0X38.28Z 80 805 0X00049Z 80 805 0X61.25Z 80 805 0X122.5Z 80 805 0X00245Z 80 805 0Y04.22Z 80 805 0Y06.75Z 80 805 0Y07.66Z 80 805 0Y12.25Z 80 805 0Y15.31Z 80 805 0Y024.5Z 80 805 0Y38.28Z 80 805 0Y00049Z 80 805 0Y61.25Z 80 805 0Y122.5Z 80 805 0Y00245Z 80 815 0X04.22Z 80 815 0X06.75Z 80 815 0X07.66Z 80 815 0X12.25Z 80 815 0X15.31Z 80 815 0X024.5Z 80 815 0X38.28Z 80 815 0X00049Z 80 815 0X61.25Z 80 815 0X122.5Z 80 815 0X00245Z 80 815 0Y04.22Z 80 815 0Y06.75Z 80 815 0Y07.66Z 80 815 0Y12.25Z 80 815 0Y15.31Z 80 815 0Y024.5Z 80 815 0Y38.28Z 80 815 0Y00049Z 80 815 0Y61.25Z 80 815 0Y122.5Z 80 815 0Y00245Z 82 800 0 81 035 0 5 82 800 0 81 035 0 5 82 810 0 81 035 0 5 82 810 0 81 035 0 5 6 6 16.3 15.7 44 920 6 6 17 15.6 40 920 6 6 10.3 9.4 45 820 6 6 9.5 8.7 46 820 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/34 CrouzetMotors.book Page 35 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 80 805 0 Nominal speed and torque curves 80 815 0 mN.m mN.m 5000 5000 1000 1000 1 1 100 1 2 5 10 100 100 1 2 5 10 500 B RPM 100 500 B RPM Dimensions 80 805 0 2 1 3 128.5 max. 4 B 4 fixing holes O 4.2 C 2 tags IEC 760 series 4.8 x 0.5 mm D 7 mm 0.1 across flats E (shaft pushed-in ) 80 815 0 Standard 2 1 3 113.5 max. 4 4 B 4 fixing holes O 4.2 C 2 tags IEC 760 series 4.8 x 0.5 mm D 7 mm 0.1 across flats E (shaft pushed-in ) Options Gearbox shaft 79 290 064 1 B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/35 CrouzetMotors.book Page 36 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 5 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 5 Nm. 10 and 17 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 1 to 208 rpm. Specifications Type Voltage Output speed Ratios (i) (rpm) 208 12.5 156 50/3 104 25 62 125/3 42 62.5 21 125 10 250 5.20 500 1.04 2500 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 1 millions turns N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 17 Watts 17 Watts 10 watts 10 Watts 80 807 0 12 V 80 807 0 24 V 80 817 0 12 V 80 817 0 24 V 80 807 012 80 807 0X16.67Z 80 807 013 80 807 014 80 807 015 80 807 016 80 807 0X00250Z 80 807 017 80 807 0X2500Z 80 807 018 80 807 0Y16.67Z 80 807 019 80 807 020 80 807 021 80 807 001 80 807 0Y00250Z 80 807 022 80 807 0Y02500Z 80 817 0X012.5Z 80 817 0X16.67Z 80 817 0X00025Z 80 817 0X41.67Z 80 817 0X062.5Z 80 817 0X00125Z 80 817 0X00250Z 80 817 0X00500Z 80 817 0X02500Z 80 817 0Y012.5Z 80 817 0Y16.67Z 80 817 0Y00025Z 80 817 0Y41.67Z 80 817 0Y062.5Z 80 817 0Y00125Z 80 817 0Y00250Z 80 817 0Y00500Z 80 817 0Y02500Z 82 800 0 81 037 0 5 82 800 0 81 037 0 5 82 810 0 81 037 0 5 82 810 0 81 037 0 5 2 3 16.3 15.7 44 800 2 3 17 15.6 40 800 2 3 10.3 9.4 45 710 2 3 9.5 8.7 46 710 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/36 CrouzetMotors.book Page 37 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 80 807 0 Nominal speed and torque curves 80 817 0 mN.m mN.m 30000 30000 10000 10000 3000 3000 1000 1000 12V 24V-48V 300 300 1 1 100 100 1 2 3 10 20 30 1 100 200 300 B RPM 2 3 10 20 30 100 200300 B RPM Dimensions 80 807 0 Standard 2 1 121 max. B C D 3 2 tags IEC 760 series 4.8 x 0.5 mm 7 mm across flats (shaft pushed-in ) 80 817 0 Standard 2 1 106 max. 3 B 2 tags IEC 760 series 4.8 x 0.5 mm C 7 mm across flats D (shaft pushed-in ) 4 Options Gearbox shaft 79 206 478 1 B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/37 CrouzetMotors.book Page 38 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 5 Nm 33 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 5 Nm. 33 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 7.4 to 426 rpm. Specifications Type Voltage Standard speed (rpm) Output speed (rpm) Ratios (i) 426 4.22 266 6.75 235 7.66 147 12.25 118 15.31 73 24.5 47 38.28 37 49 29.4 61.25 14.7 122.5 7.4 245 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (N.m) Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 33 Watts 33 Watts 80 835 0 12 V 1800 rpm 80 835 0 24 V 1800 rpm 80 835 0X04.22Z 80 835 012 80 835 0X07.66Z 80 835 013 80 835 0X15.31Z 80 835 014 80 835 015 80 835 0X00049Z 80 835 016 80 835 017 80 835 018 80 835 0Y04.22Z 80 835 009 80 835 0Y07.66Z 80 835 004 80 835 0Y15.31Z 80 835 002 80 835 003 80 835 0Y00049Z 80 835 008 80 835 006 80 835 005 82 830 0 81 035 0 5 82 830 0 81 035 0 5 6 6 33 27 50 1540 6 6 33 27 50 1540 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/38 CrouzetMotors.book Page 39 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 5000 1000 100 1 2 5 10 1 100 500 B RPM Dimensions 80 835 0 4 1 3 2 B 4 fixing holes O 4.2 C Lead length 200 mm 10 D 7 mm across flats E (shaft pushed-in ) Options Gearbox shaft 79 290 064 1 4 B (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/39 CrouzetMotors.book Page 40 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 5 Nm 40 to 52 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 5 Nm. 40 to 52 Watt motor versions. Available in either 12 or 24 V D.C. Gearbox ratios options for 13.8 to 805 rpm. Specifications Type Voltages Standard speed (rpm) Output speed (rpm) Ratios (i) 805 4.22 503 6.75 444 7.66 277 12.25 222 15.31 139 24.5 89 38.28 69 49 55 61.25 28 122.5 13.8 245 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions (2.5 million revolution) (N.m) Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 42 Watts 52 Watts 80 855 0 12 V 3400 rpm 80 855 0 24 V 3400 rpm 80 855 0X04.22Z 80 855 0X06.75Z 80 855 0X07.66Z 80 855 0X12.25Z 80 855 0X15.31Z 80 855 0X024.5Z 80 855 0X38.28Z 80 855 0X00049Z 80 855 0X61.25Z 80 855 0X122.5Z 80 855 0X00245Z 80 855 0Y04.22Z 80 855 0Y06.75Z 80 855 0Y07.66Z 80 855 0Y12.25Z 80 855 0Y15.31Z 80 855 0Y024.5Z 80 855 0Y38.28Z 80 855 0Y00049Z 80 855 0Y61.25Z 80 855 0Y122.5Z 80 855 0Y00245Z 82 850 0 81 035 0 5 82 850 0 81 035 0 5 6 6 42 32 45 985 6 6 52 32 45 985 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/40 CrouzetMotors.book Page 41 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN. m 5000 1000 1 100 1 2 5 10 100 B RPM Dimensions 3 1 2 4 B 4 fixing holes O 4.2 C 7 mm 0.1 across flats D 2 holes M3 x 0.5 at 180 depth 4 on O 32 E 2 holes 2.5 0.5 at 120 depth 4.5 on O 32 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/41 CrouzetMotors.book Page 42 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 6 Nm 10 and 17 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 6 Nm. 10 and 17 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 4 to 12 rpm. Specifications Type Voltage Output speed Ratios (i) (rpm) 12 650/3 8 338 4 650 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 10 millions turns N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 10 Watts 10 Watts 17 Watts 17 Watts 82 812 5 12 V 82 812 5 24 V 82 802 5 12 V 82 802 5 24 V 82 812 5X216.7Z 82 812 5X00338Z 82 812 5X00650Z 82 812 5Y216.7Z 82 812 5Y00338Z 82 812 5Y00650Z 82 802 5X216.7Z 82 802 5X00338Z 82 802 5X00650Z 82 802 5Y216.7Z 82 802 5Y00338Z 82 802 5Y00650Z 82 810 0 81 032 6 6 82 810 0 81 032 6 6 82 800 0 81 032 6 6 82 800 0 81 032 6 6 3.5 5 10.3 9.4 45 880 3.5 5 9.5 8.7 46 880 3.5 5 16.3 15.7 44 880 3.5 5 17 15.6 40 880 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/42 CrouzetMotors.book Page 43 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves 82 812 5 Nominal speed and torque curves 82 802 5 mN.m mN.m 30000 30000 12V 10000 10000 24V-48V 3000 3000 1 1 1000 2 3 1 10 1000 100 20 30 1 B RPM 2 3 10 20 30 100 B RPM Dimensions 82 812 5 Standard 3 1 2 25.1 130 max. 3 19.8 25.1 11.5 19.85 19.85 1.85 59.7 max. 26.9 max. 5 25.3 4 -0 0.5 14.5 O12 5.5 O8 -0.015 O42 85 max. 1.6 81.6 max. 14.5 21.5 29.1 39.7 27.25 15 25.3 64.1 max. B 8 holes M4 depth 7.5 mm C 3 holes M5 at 120 depth 7.5 mm D 2 tags IEC 760 series 4.8 x 0.5 mm E 7 mm across flats F (shaft pushed-in ) 82 802 5 Standard 3 1 2 25.1 144.5 max. 3 19.8 25.1 11.5 19.85 19.85 1.85 59.7 max. 26.9 max. 5 4 25.3 4 -0 0.5 14.5 O12 5.5 O8 -0.015 O42 85 max. 1.6 81.6 max. 14.5 21.5 29.1 39.7 27.25 15 25.3 64.1 max. B 8 holes M4 depth 7.5 mm C 3 holes M5 at 120 depth 7.5 mm D 2 tags IEC 760 series 4.8 x 0.5 mm E 7 mm across flats F (shaft pushed-in ) Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/43 CrouzetMotors.book Page 44 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 6 Nm 33 Watts A range of D.C. geared motors with solid metal gears. Mechanical rating of gearbox with output shaft stalled : 6 Nm. 33 Watt motor power. Available in either 12, 24 or 48 V D.C. Gearbox ratios options for 5 to 14 rpm. Specifications Type Voltages Output speed (rpm) Ratios (i) 14 130 8 650/3 5 338 General characteristics Motor Gearbox Maximum permitted torque from gearmotor under continuous conditions for 10 millions turns N.m Axial load (dynamic) daN Radial load (dynamic) daN Max. output (W) Nominal output (W) Gearbox case temperature rise (C) Weight (g) 33 Watts 33 Watts 82 832 5 12 V 82 832 5 24 V 82 832 5X00130Z 82 832 5X216.7Z 82 832 5X00338Z 82 832 5Y00130Z 82 832 5Y216.7Z 82 832 5Y00338Z 82 830 0 81 032 6 6 82 830 0 81 032 6 6 3.5 5 33 27 50 1400 3.5 5 33 27 50 1400 Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/44 CrouzetMotors.book Page 45 Wednesday, July 7, 2004 2:51 PM Curves The shaded zone represents the operating range of the geared motor. The horizontal line marks the maximum torque available in continuous duty cycle for a given life. For higher torque ratings, service life will be reduced. Nominal speed and torque curves mN.m 30000 10000 3000 1 1000 1 10 2 3 20 30 100 B RPM Dimensions 82 832 5 2 1 6 3 5 4 B 3 holes M5 at 120 depth 7.5 mm C 8 holes M4 depth 7.5 mm D Lead length 200 mm E 7 mm across flats F 4 holes M5 on O 40 depth 7 mm G (shaft pushed-in ) 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/45 CrouzetMotors.book Page 46 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 50 Nm 22 to 42 Watts Gearbox torque rating : 0.8 to 25 Nm. Associated DC motors : 15 to 90 watts. DC planetary geared motors with brushes Speed range : 11 to 454 rpm. Specifications 22 Watts Type Voltages Number of Speed (rpm) stages 1 454 1 477 2 122 2 128 2 69 2 70 3 33 3 34 3 20 3 19 3 12 3 11 General characteristics Motor Gearbox Max. torque Nm 42 Watts 80 809 2 12 V 80 859 3 24 V 12 V 24 V Ratios 6.75 6.75 25.0 25.0 46 46 93 93 169 169 308 308 80 809 2X06.75 80 809 2Y06.75 80 809 2X00025 80 809 2Y00025 80 809 2X00046 80 809 2Y00046 80 809 2X00093 80 809 2Y00093 80 809 2X00169 80 809 2Y00169 80 809 2X00308 80 809 2Y00308 82 800 5 81 049 2 0.8 (1 stage) 2 (2 stages) 4 (3 stages) 0.75 (1 stage) 0.7 (2 stages) 0.65 (3 stages) 1.5 (1 stage) 3 (2 stages) 4.5 (3 stages) 0.5 (1 stage) 1 (2 stages) 1.5 (3 stages) No Yes Efficiency (%) Radial load (dynamic) daN Axial load (dynamic) daN Output ball bearing Sintered bronze output bearing 80 859 3X06.75 80 859 3Y06.75 80 859 3X00025 80 859 3Y00025 80 859 3X00046 80 859 3Y00046 80 859 3X00093 80 859 3Y00093 80 859 3X00169 80 859 3Y00169 80 859 3X00308 80 859 3Y00308 82 850 0 81 049 3 3 (1 stage) 7.5 (2 stages) 15 (3 stages) 0.8 (1 stage) 0.75 (2 stages) 0.7 (3 stages) 16 (1 stage) 23 (2 stages) 30 (3 stages) 5 (1 stage) 8 (2 stages) 11 (3 stages) Yes No Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/46 CrouzetMotors.book Page 47 Wednesday, July 7, 2004 2:51 PM Curves 80 809 2 80 859 3 N.m 100 N.m 100 10 10 1 1 1 0.1 1 10 100 1 0.1 1000 1 B RPM 10 100 1000 B RPM Dimensions 80 809 2 25 19.8 4 11.5 O 42 0.5 3 2 1 2.8 6.9 2 O8 O 25h10 O 42 50 0.2 + 14.3 L1 13 B Key 3 x 3 x 16 C 4 M4 x 10 on O 36 D 4 holes for M3 self-tapping screws on O32, depth 10 E 2 tags 4.75 L1 1 stage : 134 mm L1 2 stages : 147 mm L1 3 stages : 160 mm 1 10 2 200 2.8 3 90 10 L1 5 O8 O 25h10 2.5 2 26 O -0.01 -0.01 12,7 -0.05 25 O 22 -0.05 O 42,21 max. 80 859 3 4 3 4 B Key 3 x 3 x 16 C 2 M3 x 0.5 at 180 depth 5.5 on O32 D 2 M3 x 0.5 at 120 depth 5.5 on O32 E 4 M4 x 10 on O36 F 4 M3 x 10 on O32 L1 1 stage : 162 mm L1 2 stages : 175 mm L1 3 stages : 188 mm Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/47 CrouzetMotors.book Page 48 Wednesday, July 7, 2004 2:51 PM D.C. geared motors with brushes 50 Nm 67 to 195 Watts Gearbox torque rating : 0.8 to 25 Nm. Associated DC motors : 15 to 90 watts. DC planetary geared motors with brushes Speed range : 11 to 454 rpm. Specifications 67 Watts Type Voltages Number of Speed (rpm) stages 1 410 1 474 2 110 2 128 2 62 2 70 3 30 3 34 3 18 3 19 3 11 3 11 General characteristics Motor Gearbox Max. torque Nm 195 Watts 80 839 4 12 V 80 899 5 24 V 24 V 48 V Ratios 6.75 6.75 25.0 25.0 46 46 93 93 169 169 308 308 80 839 4X06.75 80 839 4Y06.75 80 839 4X00025 80 839 4Y00025 80 839 4X00046 80 839 4Y00046 80 839 4X00093 80 839 4Y00093 80 839 4X00169 80 839 4Y00169 80 839 4X00308 80 839 4Y00308 82 830 5 81 049 4 2 (1 stage) 5 (2 stages) 10 (3 stages) 0.75 (1 stage) 0.7 (2 stages) 0.65 (3 stages) 20 (1 stage) 32 (2 stages) 45 (3 stages) 6 (1 stage) 10 (2 stages) 15 (3 stages) Yes No Efficiency (%) Radial load (dynamic) daN Axial load (dynamic) daN Output ball bearing Sintered bronze output bearing 80 899 5X06.75 80 899 5Z06.75 80 899 5X00025 80 899 5Z00025 80 899 5X00046 80 899 5Z00046 80 899 5X00093 80 899 5Z00093 80 899 5X00169 80 899 5Z00169 80 899 5X00308 80 899 5Z00308 82 890 0 82 849 5 4 (1 stage) 12 (2 stages) 25 (3 stages) 0.8 (1 stage) 0.75 (2 stages) 0.7 (3 stages) 20 (1 stage) 32 (2 stages) 45 (3 stages) 6 (1 stage) 10 (2 stages) 15 (3 stages) Yes No Products adaptations, available on request Special supply voltages Special lead lengths Optional encoder Special connectors Special output shafts Special gearbox ratios Special gear material Special output bearings Special mounting plate Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/48 CrouzetMotors.book Page 49 Wednesday, July 7, 2004 2:51 PM Curves 80 839 4 100 80 899 5 N.m 100 10 10 1 1 N.m 1 0.1 1 10 100 0.1 1 1000 B RPM 1 10 100 1000 B RPM Dimensions 80 839 4 -0 25 30 2.8 ' 0.1 O 12 h7 2.5 L1 O 32 h8 90 O 63.2 max. 3 1 2 200 O 25 -0.05 O 40 10 25 O 52 2 B Key 4 x 4 x 16 C 4 M5 x 0.86 h depth 7 on O 40 D 4 M5 x 10 L1 1 stage : 159 mm L1 2 stages : 173 mm L1 3 stages : 187 mm 80 899 5 -0 25 30 2.8 ' L1 O 12 h7 0.1 O 32 h8 90 O 63.2 max. 2.5 3 1 2 200 O 25 -0.05 O 40 10 25 O 52 4 2 B Key 4 x 4 x 16 C 4 M5 x 0.86 h depth 7 on O 40 D 4 M5 x 10 L1 1 stage : 184 mm L1 2 stages : 198 mm L1 3 stages : 212 mm Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/49 CrouzetMotors.book Page 50 Wednesday, July 7, 2004 2:51 PM Magnetic Encoder For motors: 82 800 0 - 82 810 0 - 82 800 5 - 82 810 5 - 82 860 For geared motors: 80 813 0 - 80 814 0 - 80 803 0 - 80 804 0 - 82 842 5 - 82 842 6 - 82 862 5 - 82 862 6 Magnetic encoders, resolution of 1 pulse per revolution Technology A magnetic wave is generated by a magnet integrated in the motor shaft. A Hall effect sensor reads this information and converts it into a square wave within the motor. General layout Vdc from .4 to 24 volts - current: 50 mA Output Signal 82 800 0 - 82 810 0 - 82 800 5 - 82 810 5 - 80 313 0 - 80 814 0 - 80 803 0 - 80 604 0 Applications Measuring systems for feed dispensing equipment Position settings for automatic access points Servomotors Magnetic encoder gives resolution of 5 pulses per revolution Made to order products, available on request Connections - Motor and encoder power supplies must be kept separate 12345- Motor Supply + Encoder supply + Encoder ground Encoder output ~ Motor ground 1- An integrated connector HE14 / 2.54 mm is used for motor and encoder power supplies and encoder output signals. 2 - Resistance R should be added (Value depends on Vdc) 3- Recommended customer connectors : STOCKO MKF 17-230/260/330/360 - LUMBERG 2.5 MBX 82 860 - 82 842 5 - 82 842 6 - 82 862 5 - 82 862 6 Applications Positioning dental radiology equipment Adjusting Venetian blinds Measuring systems for coffee machines Magnetic encoder with a resolution of 5 or 12 pulses per revolution Made to order products, available on request Connections - Motor and encoder power supplies must be kept separate 12345- + Motor supply output tag - Motor supply output tag Brown wire for + Vdc encoder supply Yellow wire for encoder signal Blue wire for encoder ground 1 - Encoder power supply and signal : lead length 135 mm 2 - Resistance R should be added (Value depends on Vdc) 3 - Standard motors 82 860 5 with magnetic encoders are equipped with interference suppression Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/50 CrouzetMotors.book Page 51 Wednesday, July 7, 2004 2:51 PM Friction clutch for 81 021 This device is situated inside the gearbox and is particularly recommended when gearbox protection is required if accidental overloading occurs. In this system, the final gear is connected to the gearbox output shaft by means of a friction assembly. In some cases, this device can be used for time adjustment or zero reset on timers. The standard torque setting is : 1.8 to 2.5 cm/kg for gearbox 81 021 Needle Bearings for 81 032 Where operating conditions are severe, e.g. where there are high radial or alternating loads, it is advisable for needle bearings to be substituted for the normal bearings. Please consult us. Note: applies to 81 032 gearboxes only. Cover 2 for 81 032 4 Products and specifications subject to change without notice. Order/Technical Support - Tel: (800) 677-5311 / FAX: (800) 677-3865 / www.crouzet-usa.com 4/51